| 1 | 1 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources). | BI01010001010000000000000515BI0100001113 | 1.8 | cum |
|---|
| 2 | 2 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Sal wood | BI01010001010000000000000515BI0100001114 | 0.3 | cum |
|---|
| 3 | 3 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class teak wood 30 mm thick | BI01010001010000000000000515BI0100001115 | 10.8 | sqm |
|---|
| 4 | 4 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws | BI01010001010000000000000515BI0100001116 | 2.52 | sqm |
|---|
| 5 | 5 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm | BI01010001010000000000000515BI0100001117 | 8 | each |
|---|
| 6 | 6 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :200x10 mm | BI01010001010000000000000515BI0100001118 | 8 | each |
|---|
| 7 | 7 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125 mm | BI01010001010000000000000515BI0100001119 | 8 | each |
|---|
| 8 | 8 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper | BI01010001010000000000000515BI0100001120 | 24 | each |
|---|
| 9 | 9 | Providing and fixing to existing door frames.30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. | BI01010001010000000000000515BI0100001121 | 3.99 | sqm |
|---|
| 10 | 10 | Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge. | BI01010001010000000000000515BI0100001122 | 2.1 | metre |
|---|
| 11 | 11 | Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws :30 mm thick shuttersWith ISI marked stainless steel butt hinges of required sizeSecond class teak wood | BI01010001010000000000000515BI0100001123 | 5.67 | sqm |
|---|
| 12 | 12 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all completeWith 2nd class teak wood beading 62X19 mm | BI01010001010000000000000515BI0100001124 | 37.44 | sqm |
|---|
| 13 | 13 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces | BI01010001010000000000000515BI0100001125 | 2.1 | sqm |
|---|
| 14 | 14 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) | BI01010001010000000000000515BI0100001126 | 18.2 | kg |
|---|
| 15 | 15 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25 mm thick | BI01010001010000000000000515BI0100001127 | 19.14 | sqm |
|---|
| 16 | 16 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.100 mm | BI01010001010000000000000515BI0100001128 | 3 | metre |
|---|
| 17 | 17 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification.Two or more coats on new work | BI01010001010000000000000515BI0100001129 | 324.52 | sqm |
|---|
| 18 | 18 | Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) | BI01010001010000000000000515BI0100001130 | 324.52 | sqm |
|---|
| 19 | 19 | Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel work (second coat) | BI01010001010000000000000515BI0100001131 | 164.74 | sqm |
|---|
| 20 | 20 | Painting (two or more coats) on rain water, soil waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture, over and including a priming of ready mixed zinc chromate yellow primer on new work:100 mm diameter pipes | BI01010001010000000000000515BI0100001132 | 90 | metre |
|---|
| 21 | 21 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work | BI01010001010000000000000515BI0100001133 | 2242.57 | sqm |
|---|
| 22 | 22 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. | BI01010001010000000000000515BI0100001134 | 31.92 | sqm |
|---|
| 23 | 23 | Renewing glass panes and refixing existing wooden fillets:Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) | BI01010001010000000000000515BI0100001135 | 6.4 | sqm |
|---|
| 24 | 24 | Supplying and fixing new wooden fillets wherever necessary:2nd class teak wood fillets | BI01010001010000000000000515BI0100001136 | 14.4 | metre |
|---|
| 25 | 25 | Repair to plaster of thickness 12mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge. | BI01010001010000000000000515BI0100001137 | 6 | sqm |
|---|
| 26 | 26 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. | BI01010001010000000000000515BI0100001138 | 24 | each |
|---|
| 27 | 27 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :Of area 3 sq. metres and below | BI01010001010000000000000515BI0100001139 | 2 | each |
|---|
| 28 | 28 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap | BI01010001010000000000000515BI0100001140 | 1 | each |
|---|
| 29 | 29 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe32 mm dia | BI01010001010000000000000515BI0100001141 | 80 | each |
|---|
| 30 | 30 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. | BI01010001010000000000000515BI0100001142 | 16 | each |
|---|
| 31 | 31 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. | BI01010001010000000000000515BI0100001143 | 8 | each |
|---|
| 32 | 32 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.Sand cast iron S&S as per IS - 3989 100 mm dia | BI01010001010000000000000515BI0100001144 | 1 | each |
|---|
| 33 | 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall15 mm nominal outer dia Pipes | BI01010001010000000000000515BI0100001145 | 10 | metre |
|---|
| 34 | 34 | Providing and fixing brass bib cock of approved quality :15 mm nominal bore | BI01010001010000000000000515BI0100001146 | 24 | each |
|---|
| 35 | 35 | Providing and fixing brass stop cock of approved quality :15 mm nominal bore | BI01010001010000000000000515BI0100001147 | 4 | each |
|---|
| 36 | 36 | Providing and fixing uplasticised PVC connection pipe with brass unions :30 cm length15 mm nominal bore | BI01010001010000000000000515BI0100001148 | 24 | each |
|---|
| 37 | 37 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :150 mm diameter | BI01010001010000000000000515BI0100001149 | 2 | each |
|---|
| 38 | 38 | Providing and fixing PTMT grating of approved quality and colour.Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating | BI01010001010000000000000515BI0100001150 | 80 | each |
|---|
| 39 | 39 | Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved qualityRectangular shape 600x450 mm internal dimensionsL D- 2.5 | BI01010001010000000000000515BI0100001151 | 8 | each |
|---|
| 40 | 40 | Providing and fixing PVC shuddle (clamps) at 1.00m spacing for existing 15 mm nominal outer dia pipes exposed on wall | BI01010001010000000000000515BI0100001152 | 560 | mtr |
|---|
