Tender For Slno-2 Renovation Of Community Centre Of Jaldhaka Hydel Project Located At Paren At Po-Jhp Dist- Kalimpong Pin-734503
Tender Value
20.64 Lakhs
Estimated cost
Bid Submission
26 Nov 2019
0 days left
EMD
41290
Bank guarantee accepted
Document Fee
2419
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jaldhaka Hydel Project → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
tender for Slno-2 Renovation Of Community Centre Of Jaldhaka Hydel Project Located At Paren At Po-Jhp Dist- Kalimpong Pin-734503
BOQ
| Name of Work: Renovation of community centre of Jaldhaka Hydel Project located at Paren at PO- JHP, Dist - Kalimpong, PIN 734 503 | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Taking out carefully G.C.I. or C.I. or asbestos sheets (including ridges etc.) from roof or wall after unscrewing bolts, nuts, screws etc. and stacking the material at site as directed. | BI01010001010000000000000515BI0100001113 | 300 | Sqm |
| 2 | 2 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)\n(i) In Roof:\nb) With 0.63 mm thick sheet | BI01010001010000000000000515BI0100001114 | 225 | Sqm |
| 3 | 3 | Galvanised corrugated iron sheet work (excluding the supporting frame work) fitted and fixed with 10 mm. dia J or L hook-bolts, limpet and bitumen washers and putty complete with 150 mm. end lap and one corrugation minimum side lap. (Payment to be made on area of finished work)(GCI sheet to be supplied by contractor)\n(ii) In wall:-\nb) With 0.63 mm thick sheet | BI01010001010000000000000515BI0100001115 | 125 | Sqm |
| 4 | 4 | Galvanised iron sheet ridging fitted with necessary bolts, screws, washers etc complete.(225mm end lapping)\n(A) 300 mm lapping each way\n(b) With 0.63 mm sheet | BI01010001010000000000000515BI0100001116 | 70 | M |
| 5 | 5 | Providing and fixing of false ceiling with powder coated exposed G.I. grid suspension system (E-Grid T 2430/1510 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200mm c/c ) consisting of Main Runner 3600 mm long, Cross Tee 1200 mm / 600 mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300mm c/c. The Main Runners to be placed @ 1200 mm. The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at regular interval of 600 mm to form a modular grid of 1200mm X 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600 mm X 600 mm. Grid of module size 600 mm X 600 mm shall be supported by 6 mm dia G.I. wire from purlins / soffit. 4 mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Standard Ceiling Board (Density > 1300 Kg/m3) of size 595 mm X 595 mm, conforming IS 14862 & Type B Category III of ISO 8336, tested as per AS-1530 part 3 & BS-476 Part 4,5,6,7 & 8, should be placed in the Grid module to form a False Ceiling. All complete as per the drawing & directions of Engineer-in-charge.\nIn ground floor\na) False Ceiling (with 4mm thick Fibre Cement Standard Ceiling Board and EGrid T-2430/1510). | BI01010001010000000000000515BI0100001117 | 130 | SQM |
| 6 | 6 | Rubble masonry in cement (1:6) with hard dressed stones from approved quarries and clean, coarse and washed sand including carriage of all materials to site.\n(b) In Fine dressed work in Building\n(i) In Ground Floor\n | BI01010001010000000000000515BI0100001118 | 15 | Cum |
| 7 | 7 | Plain and finished timber planks in partition, shelves etc. fitted and fixed complete as per design (butt joints) in ground floor.\n(i) 12mm thick planks\n(c) other Local wood | BI01010001010000000000000515BI0100001119 | 100 | Sqm |
| 8 | 8 | Plain and finished timber planks in partition, shelves etc. fitted and fixed complete as per design (butt joints) in ground floor.\n(iii) 25mm thick planks\n(c) other Local wood | BI01010001010000000000000515BI0100001120 | 400 | Sqm |
| 9 | 9 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.\n(A) Floor\nWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m.\n(a) Area of each tile upto 0.09 Sq.m \n (i) Coloured decorative | BI01010001010000000000000515BI0100001121 | 40 | Sqm |
| 10 | 10 | Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles including roughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc.\n(B) Wall\nWith Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m.\n(a) Area of each tile upto 0.09 Sq.m \n(i) Coloured decorative | BI01010001010000000000000515BI0100001122 | 50 | Sqm |
| 11 | 11 | (a)Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. | BI01010001010000000000000515BI0100001123 | 700 | Sq.m |
| 12 | 12 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. | BI01010001010000000000000515BI0100001125 | 1050 | Sq.m |
| 13 | 13 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : (b) On steel or other metal surface : \nWith super gloss (hi-gloss) - (iv) Two coats (with any shade except white) | BI01010001010000000000000515BI0100001126 | 700 | Sq.m |
| 14 | 14 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : \n(a) On timber or plaster surface : \nWith super gloss (hi-gloss) - \n(iv) Two coats (with any shade except white) | BI01010001010000000000000515BI0100001127 | 1050 | Sq.m |
| 15 | 15 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc.\nNOTE:Cement 0.152 cu.m per100 sq.m | BI01010001010000000000000515BI0100001128 | 250 | Sq.m |
| 16 | 16 | Stripping off worn out plaster and raking out\njoints of walls, celings etc. upto any height and in\nany floor including removing rubbish within a\nlead of 75m as directed. | BI01010001010000000000000515BI0100001129 | 250 | Sq.m |
| 17 | 17 | Stopping roof leakages in C.I. or G.C.I. or asbestos roofing. \n(iii) Closing holes in C.I. or G.C.I. or asbestos roofing with sheet bolt, limpet and bitumen washers, putty etc. | BI01010001010000000000000515BI0100001130 | 30 | Each |
| 18 | 18 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(b) For Concealed Work (Dia) 15 mm | BI01010001010000000000000515BI0100001131 | 35 | M |
| 19 | 19 | (a) For Exposed Work\n(Dia) 15 mm | BI01010001010000000000000515BI0100001132 | 10 | M |
| 20 | 20 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(b) For Concealed Work (Dia) 20 mm | BI01010001010000000000000515BI0100001133 | 20 | M |
| 21 | 21 | (a) For Exposed Work\n(Dia) 20 mm | BI01010001010000000000000515BI0100001134 | 10 | M |
| 22 | 22 | Supplying, fitting and fixing bib cock or stop cock.\n(a) (i) Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). | BI01010001010000000000000515BI0100001135 | 4 | Each |
| 23 | 23 | Supplying, fitting and fixing bib cock or stop cock. \n (b) (i) Chromium plated Stop Cock (Equivalent to Code No. 513(A) & 513(B) & Model - Tropical / Sumthing Special of ESSCO or similar | BI01010001010000000000000515BI0100001136 | 6 | Each |
| 24 | 24 | Labour for dismantling G.I. pipe with fittings.\n(i)15 mm & 20mm | BI01010001010000000000000515BI0100001137 | 50 | M |
| 25 | 25 | Dismantling all types of masonry excepting cement\nconcrete plain or reinforced, stacking serviceable\nmaterials at site and removing rubbish as directed\nwithin a lead of 75 m.\na) In ground floor including roof | BI01010001010000000000000515BI0100001138 | 5 | Cum |
| 26 | 26 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.\n(ii ) River Bazree | BI01010001010000000000000515BI0100001139 | 5 | Cum |
| 27 | 27 | (II) Cement concrete with 30 mm down graded shingles excluding shuttering. \nN.B. Variety\nIn ground floor\n(a) 1:3:6 proportion | BI01010001010000000000000515BI0100001140 | 12 | Cum |
| 28 | 28 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as per relevant IS codes.\n(b) River bazree | BI01010001010000000000000515BI0100001141 | 20 | Cum |
| 29 | 29 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface]\n(i) With 1:6 cement mortar\n(b) 20 mm thick plaster | BI01010001010000000000000515BI0100001142 | 250 | Sqm |
| 30 | 30 | Supplying, fitting and fixing shower of approved brand and make.\n(a) (i) Chromium plated round shower with revolving joint 100 mm dia with rubid cleaning system (Equivalent to Code No. 542(N) & Model Tropical / Sumthing Special of ESSCO or similar brand). | BI01010001010000000000000515BI0100001143 | 3 | Each |
| 31 | 31 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete,C.I. brackets including two coats of painting to bracket etc. | BI01010001010000000000000515BI0100001144 | 3 | Each |
| 32 | 32 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc\n(b) With 'S' trap | BI01010001010000000000000515BI0100001145 | 3 | Each |
| 33 | 33 | Providing & fixing factory made 30 mm thick factory made solid pvc door shutter made out of single piece extruded solid pvc profile . The style & rails shall be of size of 75 x 30 mm having wall thickness of 5 mm. The style and top bottom rail shall have one side a thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. 15 mm thickness shall be of single piece extruded solid pvc profile whereas it shall be not be made of sheet pasted profile) . The styles and rails shall be reinforced with MS tube of size 18 mm(±) 1mm x 18 mm (±) 1mm x 1mm painted with primer all four corners of reinforcement to be welded or sealed . solid pvc extruded bidding (push fit type) will be set inside the styles and rails with a cavity to receive single piece extruded 5 mm pvc sheet as panel. The styles and rails will be metered cut and join with the help of pvc solvent cement, self tapping screw and braket of size 200 x 75 mm / welded at each corner. Single piece extruded solid pvc lockrail of size 100 x 30 mm with a wall thickness 5 mm & 15 mm integrally extruded in the middle of lockrail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8mm complete as per manufacturers specifications and direction of Engineer-in-Charge. | BI01010001010000000000000515BI0100001146 | 7 | SQM |
| 34 | 34 | Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete:\n(a) With continuous plate base (Hexagonal/ Round rod)\n(vi) 150 mm grip x 10 mm dia rod. | BI01010001010000000000000515BI0100001147 | 50 | Each |
| 35 | 35 | i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with\n16mm dia rod with centre bolt and round fitting.\n(c) 300mm long | BI01010001010000000000000515BI0100001148 | 24 | Each |
| 36 | 36 | Anodised aluminium barrel / tower / socket bolt (full covered) of approved quality manufactured from extrended section conferming to I.S. 204/74 fitted and fixed with cadmium plated screws.\n (i) 200mm long x 10mm dia. | BI01010001010000000000000515BI0100001149 | 50 | Each |
| 37 | 37 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. \n (vii) 100mm x 58mm x 1.9mm | BI01010001010000000000000515BI0100001150 | 250 | Each |
| 38 | 38 | Dismantling all types of plain cement concrete\nworks, stacking serviceable materials at site and\nremoving rubbish as directed within a lead of 75m.\nIn ground floor including roof\n(a) upto 150 mm. thick | BI01010001010000000000000515BI0100001151 | 25 | Cum |
| 39 | 39 | Dismantling carefully wooden walling, flooring of\nceiling and stacking dismantled materials as\ndirected. | BI01010001010000000000000515BI0100001152 | 400 | SQM |
| 40 | 40 | Dismantling carefully wood work in posts,\npostplates, rafters, partition etc., sorting and\nstacking serviciable materials at site and removing\nrubbish as directed. | BI01010001010000000000000515BI0100001153 | 4 | Cum |
| 41 | 41 | Panel shutters of door and window, as per design (each panel consisting of single plank without joint), including fitting and fixing the same in position but excluding the cost of hinge and other fittings.\nIn ground floor.\n(In case of non-supply of single plank, penal rate of reduction of 20% will be made)\ni) 35 mm thick shutters with 19 mm th. panel \n a) Local wood | BI01010001010000000000000515BI0100001154 | 35 | Sqm |
| 42 | 42 | Shutter of 2/3 panel and 1/3 glazed of doors and window as per design (each panel consisting of a single plank with out joint and with ordinary glass of 7.4 kg per sqm/ 3 mm th) fitted with putty bed and teak wood beads and nails including fittiong and fixing shutters in position but excluding the cost of hinges and other fittings in ground floor.\n (iv) 25mm thick shutters with 12mm thick panel.\n(c) Other Local Wood. | BI01010001010000000000000515BI0100001155 | 25 | Sqm |
| 43 | 43 | Supplying, fitting and fixing pillar cock of approved make.\na) (i) CP Pillar Cock - 15 mm. (Equivalent to Code No. 507 & Model Tropical / Sumthing Special of ESSCO or similar brand) | BI01010001010000000000000515BI0100001156 | 2 | Each |
| 44 | 44 | Wash basin vitreous china of approved make (without fittings) supplied,fitted and fixed in position on 75mm X 75 mm X 75 mm wood blocks and C.I. brackets including two coats of painting of C.I. brackets.\n(i) 450 mm X 300 mm size | BI01010001010000000000000515BI0100001157 | 2 | Each |
| 45 | 45 | Wood work in upper rails of railing, hand rail of staircase, balcony etc. includig necessary bend, moulding fitted and fixed complete (for purpose of payment\nsection will be measured in the square).\n(d) Other Local Wood. | BI01010001010000000000000515BI0100001158 | 3 | Cum |
| 46 | 46 | (A) Wood work in posts, post plates, rafters, battens, truss members, purlins etc. fitted and fixed complete (excluding the cost of bolts, paints, but including the cost of nails, screws etc.) \n(The quantum should be corrected upto three decimals)\n(ii) Sal : Local. | BI01010001010000000000000515BI0100001159 | 1.5 | Cum |
| 47 | 47 | M.S. structural works with hollow sections (square or rectangular\nshape) conforming to IS: 806-1968 & IS:1161-1998) connected to\none another with bracket, gusset, cleat as per design, drawing &\ndirection of Engineer-in-Charge complete including cutting to\nrequisite shape & size, fabrication including metal arc welding\nconforming to IS: 816-1969 & IS: 9595 using electrodes of approved\nmake and brand conforming to IS:814- 2004, haulage, hoisting and\nerection all complete. The rate includes the cost of all M.S. Hollow section, all consumables such as electrodes, gas and hire charges of all tools\nand plants and labour reqired for execution and all incidental\nchages (such as electricity, labour insurance) etc. complete. \nPayment to be made on the basis of calculated weight of structural\nmemebrs of MS Holow Section as specified in relevent IS code in\nfinished work. Payment for gusset, bracket, cleat may be made by\nadding the actual weight of such items with weight of finished\nstructural members. The rates are considered for a hight of erection\n8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate\nfor each additional floor or 4m. beyond the initial 8 m. or part\nthereof.\ni) For roof truss works\na) Span up to 12 Mtr | BI01010001010000000000000515BI0100001160 | 0.7 | MT |
| 48 | 48 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS: 226, IS: 808 & SP (6)- 1964 connected to one another with bracket, gussets, cleats as per design, direction of Engineer-incharge complete including cutting to requisite shape and length,\nfabrication with necessary bolting, metal arc welding conforming to IS: 816- 1969 & IS: 1995 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section,\nconsumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. Payment\nfor gusset, bracket, cleat, rivets, bolts and nuts may be make by adding the actual weight of such items with the weight of finished structural members or 7% of weight for finished structural members weighing not less than 22.5 Kg. / m. or 15 % of weight for finished structal members weighing less than 22.5 Kg. / m. may be increased\nallow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for each additional floor or 4m. beyond initiial 8m. or part thereof.\nI) For structural members of specified sections weighing less than\n22.5 Kg./m | BI01010001010000000000000515BI0100001161 | 0.7 | MT |
| 49 | 49 | Earth work in excavation of foundation trenches or\ndrains, in all sorts of soil (including mixed soil but\nexcluding laterite or sandstone) including removing,\nspreading or stacking the spoils within a lead of 75 m.\nas directed. The item includes necessary trimming the\nsides of trenches, levelling, dressing and ramming the\nbottom, bailing out water as required complete. \n(a) Depth of excavation not exceeding 1,500 mm | BI01010001010000000000000515BI0100001162 | 10 | Cum |
| 50 | 50 | Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m.\na) In ground floor including roof. | BI01010001010000000000000515BI0100001163 | 50 | Sqm |
| 51 | 51 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinge.\n(i) 450 mm X 300 mm | BI01010001010000000000000515BI0100001164 | 2 | Each |
AI Tender Summary
Tender Timeline
Nov 11, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedNov 26, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedDec 02, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender