Providing Installation Testing Commissioning Of 5000 Gph X 150 M Head Hcps Including Their Other Allied Works At Ps Dharamkot In Billawar
Tender Value
Ref. Documents
Estimated cost
Bid Submission
18 Nov 2019
0 days left
EMD
19000
Bank guarantee accepted
Document Fee
200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dharamkot → Jammu And Kashmir
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Providing Installation Testing Commissioning Of 5000 Gph X 150 M Head Hcps Including Their Other Allied Works At Ps Dharamkot In Billawar
BOQ
| Name of Work: Providing, installation, testing & commissioning of 5000 GPH x 150 m head HCPs including their other allied works at P/S Dharamkot in Billawar. | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Providing, installation, testing and commissioning of multi stage side suction horizontal centrifugal pump sets with diffuser type casing of 5000 GPH x 150 m head . The pump shaft is supported in antifriction bearings. Enclosed impellers are of radial flow type provided with balancing holes. The pumps have standard lubrication of grease and are suitable for coupling with electric motors. The recommended make of pump:- Kirloskar, KSB, Mather Platt, Beacon weir and recommended make of motor:- Kirloskar, ABB, Alstom, Marathon. The specification of the motor: are 385±15%, 2900 RPM, 50Hz, 02 Pole and TEFC cooled at Dharamkot.\n1. Impeller-CI.\n2. Pump shaft-CS/ST.St.\n3. Wearing Ring-Ph.Br.\n4. Pump casing-Cast iron SG-200.\n5. Base frame-MS fabricated\nThe job includes the cost of pump set along with base frame, transportation charges up to Billawar.\n | item1 | 2 | C.Job |
| 2 | 2 | Laying of foundation block by way of shuttering of size 1.80 x 0.90 x 0.90m, providing & fixing of 15mm x 0.90 m 06 nos. foundation bolts, placing of 8mm tor steel bars in a mesh off 0.15 x 0.15 m horizontally as well as vertically by using suitable winding wires after proper leveling the base frame, keeping of base frame of the HCP horizontally on top of the shuttering , laying of cement concrete in 1:2:4 mix. by using vibrator so that mixing of cement concrete is done in a proper manner. The complete job includes skilled, semiskilled labourers, cost of material ,carriage of motor pump set from road site to pumping station, carriage of sand & bajri from nallah to site of work including carriage of other materials, cost of 8mm dia tor steel , Cement, shuttering material, hire charges of tools and tackles involved including curing of laid cement concrete block for 07 days.\nLeveling of base frame by placing the base frame of the pump and motor on top of the base frame manually with sprit level by way of adding shims etc. so that pump and motor can be coupled without any offset. Fitting the Pump set by using heavy duty nuts, bolts, washers with proper alignment. The job includes the cost of material and labour charges.\nFabrication of suction pipe line for 5000 GPH x 150 m head multi stage centrifugal booster pump by way of fabrication of M.S.flanges, fabrication of suction pipe line by using required 80 mm dia. M.S bends and flanges as per site requirement. P/F of 01 no. 80 mm dia. sluice valve. The welding work should be homogeneous and of good quality by using quality electrodes. The job includes cutting and welding of pipes with flanges, providing and fitting of nuts, bolts , rubber gaskets and other allied material. The job includes cost of all sort of material including skilled and semiskilled labour charges.\nFabrication of delivery pipe line for 5000 GPH x 150 m head multi stage centrifugal booster pump by way of fabrication of M.S.flanges, fabrication of delivery pipe line by using required 80 mm dia. M.S bends and flanges as per site requirement. Providing and Fitting of 80mm dia. sluice valve and 01 no. check valve of quality make on delivery pipe line of the HCP using MS flanges on its both ends. The welding work should be homogeneous and of good quality by using quality electrodes. The job includes cutting and welding of pipes with flanges, providing and fitting of nuts, bolts, rubber gaskets and other allied material. The job includes cost of all sort of material including skilled and semiskilled labour charges.\n | item2 | 2 | C.Job |
| 3 | 3 | Fabrication of suction pipe line manifold of HC pump sets , interconnection of both HCP suction line by fabrication of common suction manifold of 100mm dia. G.I pipe line as per site conditions. Manifold has to be connected with dug well through common 80 mm dia. pipe line by way of welding the pipe line from sump tank, the other side of manifold should have two branches to facilitate interconnections with both HC pump sets by way of welding two no out lets of 80 mm dia. The job also includes providing & fitting of one no new sluice valve in suction pipe line of existing HC pump sets by way of providing 80mm dia.MS flanges on its both ends. The job includes cost of all sort of material , labour charges ,hire charges of welding set, cost of nuts bolts, rubber gaskets , cost of skilled and semi skilled labour etc. \nFabrication of delivery pipe line manifold of HC pump sets , interconnection of both HCP delivery pipe line by fabrication of common delivery manifold of 100 mm dia. G.I pipe line as per site conditions. Manifold has to be connected with rising main through common 80 mm dia. pipe line by way of welding the pipe line from deliveries of both HC pump sets, the other side of manifold should have two branches to facilitate the interconnections with both delivery pipe lines of the HC pump sets by way of welding two no out lets of 80mm dia. P/F of 01 no. 80mm dia. sluice valve and 01 no. 80 mm dia. reflex valve .P/F of bends duly flanged in delivery pipe line of existing HC pump sets by way of providing 65 mm dia.MS flanges on its both ends. The job includes cost of all sort of material , labour charges ,hire charges of welding set, cost of nuts bolts, rubber gaskets , cost of skilled and semi skilled labour etc.\n | item3 | 1 | C.Job |
| 4 | 4 | Fabrication of the panel board made out of angle iron and having a size of 6'x 3'. The angle iron is to be welded at corners properly and flushed in all directions including its grinding or foiling to avoid body scratches. The panel board is to be surmounted with a ply board of 12mm thickness with bakelite or some other insulating material on top. The job includes cost of all sort of material and labour charges.\nProviding and fitting of 320 Amp, 415 Volt, HRC fuse type Main Switch & 320 ampere Bus bar of reputed make and allied works.\nProviding and fitting of 3 pole 160 Amp MCCB having breaking capacity of 36 kA of Havell’s/L&T/National/HPL make. The MCCB is to be enclosed in the SS enclosure and to be fitted on wooden panel board. The SS enclosure must have IK08 and IP 30 protection and it must be suitable to accommodate Al./copper cable. The job includes the cost of material, fixation, transport and labour charges.\nComplete painting of suction pipe line and delivery pipe lines at pumping station Dharamkot. The job includes clearing the surfaces of the pipe lines, bends, flanges with cloth to remove dust and dirt, rubbing the pipe lines with the help of emerre cloth. The job includes applying a primary coat of red oxide paint and subsequently applying two coats of black synthetic enamel paint of approved quality. The job includes cost of material as well as labour charges.\nEarthing of the electromechanical machinery. The job includes digging of a pit on the earth which should not be less than 3m (10ft) from the ground level. A plate made up of copper with dimensions 60cm x 60cm x 3.18mm or galvanized iron (GI) of dimensions 60cm x 60cm x 5 mm is buried vertical in the earth (earth pit) which should not be less than 3m (10ft) from the ground level. Put about 30 cm layer of powdered charcoal and lime mixture around the earth plate. Providing and fitting of 40 mm dia. GI pipe of 2.5 m length and GI strip of 32mm X 06 mm along with nuts and bolts inside the pit. Providing and fitting of 25 mm dia GI pipe for putting water inside the pit to maintain moisture. The strip is to be attached with electromechanical machinery. The job includes the cost of material, labour, transport charges and any other miscellaneous charges.\nElectrification of the pump room by way of providing and fitting of 02 no. lightening points inside the pump room and 02 nos. outside the pump room along with LED lights. The job also includes 02 nos. 06 amp. Sockets and 02 nos. 16 amp. Sockets inside the pump room. The job includes laying of cable and batten of appropriate size required to cover all the points.\n | item4 | 1 | C.Job |
| 5 | 5 | Providing, fitting, testing and commissioning of 16mm sq. 3 core multi strand copper wires from main switch to panel and panel to induction motor. The job includes proper thimbling at each end. The copper wires should be of IS specifications. The job includes cost of material and labour charges | item5 | 30 | meter |
AI Tender Summary
Tender Timeline
Nov 06, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedNov 18, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 19, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender