Tender For Addition/Alteration To Library At Hmi Darjeeling
Tender Value
35 Lakhs
Estimated cost
Bid Submission
12 Nov 2019
0 days left
EMD
70000
Bank guarantee accepted
Document Fee
1200
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
HMI DARJEELING → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition / Alteration To Library At Hmi Darjeeling
BOQ
| Name of Work: ADDITION/ALTERATION TO LIBRARY AT HMI DARJEELING | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Dismantling of boarding, any description, fixed in any position with screws complete all as specified and as directed. | 110 | Sqm | |
| 2 | 2 | Dismantling of wall and ceiling boards (Fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including over fillets all as directed. | 20 | Sqm | |
| 3 | 3 | Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles, all as specified . | 5 | Cum | |
| 4 | 4 | Demolition/cutting of reinforced cement concrete for lapping of reinfocement for roof slab of any description and an any position not otherwise specifically provided and disposed the materials in low lying area complete all as directed by Campus Supdt. | 1 | Cum | |
| 5 | 5 | Taking down chowkats or frame with shutters (without taking off shutters from the frames) n. exc 1.5 Sqm each complete all as specified. | 4 | Each | |
| 6 | 6 | All as per item No above but exc 1.5 Sqm but n.exc. 4 Sqm complete all as specified | 11 | Each | |
| 7 | 7 | Taking down reception counter complete all as specified and as directed. | 1 | Each | |
| 8 | 8 | Taking down cement plaster on brick/stone walls including raking out joints, hacking for key, scrubbing down with water all as directed. | 50 | Sqm | |
| 9 | 9 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness complete all as specified and as directed. | 50 | Sqm | |
| 10 | 10 | Dismantling of structural steel work of any description complete all as specified and as directed. | 0.25 | Qtl | |
| 11 | 11 | Dismantling of timber scantling in any section fixed in any positing with nails or screws complete. | 0.25 | Cum | |
| 12 | 12 | M&L for cutting openings of brick wall built in cement mortar or cement lime mortar, through brick wall for door, window and other openings or enlarging existing openings, converting window into door opening, etc or cutting out defective brick work for under pinning, including removing rubbish from site and making good dismantled portion in cement mortar 1:3 complete all as specified and directed. | 18 | Each | |
| 13 | 13 | Excavation in trenches in soil n.exc 1.5 m wide and n.exc 1.50m in depth for foundation, pier holes etc n exc 10 sqm on plan and getting out complete. | 25 | Cum | |
| 14 | 14 | M & L for broken stone or boulders hardcore of guage n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick , watered and rolled/rammed to a true surface | 11 | Cum | |
| 15 | 15 | Material and labour cement concrete 1:4:8 type D-2 using 40mm graded agg as in foundations filling and in mass concrete complete all as specified and as directed. | 11 | Cum | |
| 16 | 16 | Material and labour cement concrete 1:3:6 type C2 using 20mm graded stone aggregate as in floor complete all as specified and as directed. | 8.5 | Cum | |
| 17 | 17 | Material and labour 40 mm thick cement concrete 1:2:4 type B1 using 20mm graded stone aggregate as in floor complete all as specified and as directed. | 130 | Sqm | |
| 18 | 18 | M&L for 38 mm wide x 3 mm thick glass dividing strips as in floor etc | 80 | RM | |
| 19 | 19 | M & L for RCC M-25 (20 mm graded aggregate) for foundation including rafts footings foundation beams plinth beams etc | 9 | Cum | |
| 20 | 20 | M & L for RCC M-25 (20 mm graded aggregate) for columns, pillars, piers, posts and struts etc | 3.85 | Cum | |
| 21 | 21 | M & L for RCC M-25 (20 mm graded aggregate) for slabs supported on walls, beams and cloumns in floors, roofs, landings, shelves and the like | 15 | Cum | |
| 22 | 22 | M & L for formwork to sides of concrete foundations, footings, bases of cloumns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work; vertical or to batter. | 30 | Sqm | |
| 23 | 23 | M & L for formwork to sides of pillars, posts, struts, piers, columns etc | 50 | Sqm | |
| 24 | 24 | M & L for formwork to side and soffits of floor or roof beams, beam haunchings, girders, lintel shelves beams or similar work | 30 | Sqm | |
| 25 | 25 | M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) | 80 | Sqm | |
| 26 | 26 | S&F MS TMT bar 10 dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire not less than 0.90mm dia or securing with clips. | 2400 | Kg | |
| 27 | 27 | All as per items No above but TMT bar 8 mm dia as in stirrups etc | 3600 | Kg | |
| 28 | 28 | Removing excavated material exc. 50m but n exc 250m and depositing where directed at a level n.exc. 1.5 m above the starting point. | 24 | Cum | |
| 29 | 29 | Returning filling in including spreading levelling watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and directed by Engr-in-Charge. | 1 | Cum | |
| 30 | 30 | M & L rendering 10 mm thick on concrete surface of ceiling in cement mortar 1:3 finished fair and even with out using extra cement complete all as specified. | 80 | Sq.m | |
| 31 | 31 | M&L for two coats of OBD on surfaces of ceiling including one coat of primer and preparation of surfaces | 80 | Sqm | |
| 32 | 32 | M&L for screed bed or bedding layer of mortar 20 mm thick for laying floor finishes in CM 1:6 for laying of floor tiles as dierected. | 60 | Sqm | |
| 33 | 33 | M&L for 10 mm thick plaster in cement mortar 1 : 4 as a backing coat for fixing of wall tiles complete all as specified. | 68 | Sqm | |
| 34 | 34 | M&L for joint free double charged / ultra charged vitrified tiles 10-12 mm thick (square / rectangular) polished area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm in floors etc set & jointed in neat cement slurry and pointed with white or coloured cement to match complete. Make -Somany/Johnson/Kajaria | 60 | Sqm | |
| 35 | 35 | M&L for joint free glazed ceramic colour tiles in vertical surface of size 300x200x7 mm or 450 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in colour cement to match etc complete all as directed by Campus Supdt. | 68 | Sqm | |
| 36 | 36 | Supply and laying of Non-woven Felt Floor Carpet 4 mm thick with fixing materials on plain cement floor complete as per manufactuers instructions and complete all as directed. Make : Jindal/Jacquard Floor | 2800 | Sqft | |
| 37 | 37 | M & L for brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in cement mortar 1 : 6 | 2 | Cum | |
| 38 | 38 | M & L for Reinforced cement concrete nominal mix (using 20 mm graded stone aggregate) for beams, cantilevers, bressummers, lintels over 1.5m span | 1 | Cum | |
| 39 | 39 | M&L for half brick thick work built in cement mortar 1 : 4 by using sub class \"B\" brick. | 5 | Sqm | |
| 40 | 40 | M&L for RCC platform, shelves type BO 1:2:4 (12.5 mm graded aggregate) including necessary form work complete all as specified | 0.25 | Cum | |
| 41 | 41 | M & L rendering 15 mm thick on concrete surface in cement mortar 1:6 on internal wall surfaces. | 50 | Sqm | |
| 42 | 42 | Material and labour for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as directed. | 450 | KG | |
| 43 | 43 | Supply and fix pre-painted aluminium Zinc coating (Zinc coating not less than 150gm per sqm) corrugated steel sheet (galvalume base ) of thickness 0.50 mm in colour having tensile strength of 550mpa as in roof covering/cladding to wall and profile as approved by Principal and to be factory moulded and fixed with hot dipped galvanised with high durable protective triple coating self tapping screws/self drilling screws to suit the roofing in customized colour matching with the colour of roof covering/claadding to wall and screws are to be fixed using orque adjustable electronic gun screws driller of suitable capacity complete all as specified and directed by Principal HMI Darjeeling.`Make : TATA | 50 | Sqm | |
| 44 | 44 | All as per items No above but pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick as in ridge fixed with self tapping screws complete all as directed. | 3 | Sqm | |
| 45 | 45 | Supply fabricating and fixing of aluminium door powder coated of extrusion aluminium section including frame work complete, consisting of frame vertical and horizontal members, of size 104mmx44.45mmx1.8mm thick. Vertical style of door shutter of size 85mmx44.45mmx1.8mm thick. Top, middle and bottom rial of size 85mmx44.45x1.8mm thick and fixing 5 mm thick plain/tinted sheet glass of Modi guard/Atul or prelaminated particle board 9 to 10mm thick of make Kit Ply with aluminium bedding and rubber gasket/beading including frosted film as desired fixing of hydraulic floor spring one in single leaf or two nos in double leaf door of Make Kelvin/Evershine. One mortice lock for aluminium door (each) and two aluminium tower bolts for each door. Fixed with rawl plug including rectification of floor/wall to match the existing surfaces. All as specified and as directed by Engineer-in-Charge at site. (Cost of sheet glass/frosted film & sun control film shall be included in the unit of this item) | 14.5 | Sqm | |
| 46 | 46 | S&F for powder coated aluminium window three track sliding type with frames including 5mm thick tinted glass, stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm fixed with standard rubber gasket, aluminium beadings and joining cleat for fixing including locking devices complete all as specified. Make : Jindal aluminium sections Nos. 20671, 20672, 20690 & 20668 | 14 | Sqm | |
| 47 | 47 | S&F powder coated aluminium window and ventilator shutters including frame work, fixed type without sash bar including necessary joining cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws, 4 mm thick glass panes selected quality etc complete all as specified and as directed. | 17 | Sqm | |
| 48 | 48 | S&F aluminium anodised grill in one piece, 7.5mm thick having anodised thickness 15 micron fixed to grill and window frames with putty/rivets/screws 75mm clear spacing all as directed by Campus Supdt | 14 | Sqm | |
| 49 | 49 | Supply and fix mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted,or forged into spikes;framed guard bars, barred iron doors, ladders, railings / ormental design of railing and similar work con- forming to Fe.290.Gde-E-165 and fixing complete all as specified and as directed. Note : Grill and railing design whereever required will be finalised by principal HMI Darjeeling. | 80 | KG | |
| 50 | 50 | S&F stainless steel railing of grade 304 hand rail consisting of SS pipe 50 mm dia, up height studs of 40 x 40 mm square tube of height 1.20 m fixed on stair case complete all as per site requirement and directed by Campus Supdt. | 60 | RM | |
| 51 | 51 | Material and labour wall panelling /ceiling (Dhoopi only) 25 mm thick with 2nd class hardwood boarding planed one side and edges tongued and grooved or rebated and fixed with nails to timber framework including complete finishing /polishing all as specified and directed by Campus Supdt. | 20 | Sqm | |
| 52 | 52 | M&L preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer. | 20 | Sqm | |
| 53 | 53 | Material and labour for two coats 3mm thick wall care putty on wall/ceillig including on wooden surfacesincluding two coats of primer complete all as directed. Note : All scaffolding material are contractor responsibility. | 530 | Sqm | |
| 54 | 54 | Material and Labour for preparation of old decorated surfaces of any description and applying two coat of plastic emulion paint (1st quality) of desired shade with roller finish including cleaning complete all as specified and directed by principal HMI Darjeeling.\nNote : All Scaffolding material are contractor responsibility.\nMake : Asian/Berger/Nerolac | 350 | Sqm | |
| 55 | 55 | Preparation of previously untreated wood or wooden based surfaces of any description over 10cm width or girth and finishing coat with malamine spray over two coat of sealer under coating complete all as specified and directed. | 20 | Sqm | |
| 56 | 56 | Complete removal of existing treatment material and labour for two coats of cement base paint (Snowcem) 1st quality as per desired shade of principal. Note : Rate should be including of Scaffolding. Make : (Snowcem plus /TATA/Shalimar) | 150 | Sqm | |
| 57 | 57 | S&F PVC (SWR) pipes 180mm bore single socketed in any length with rubber ring joint fixed to wall with suitable PVC / GI clamp complete | 20 | RM | |
| 58 | 58 | S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joint fixed to wall with suitable PVC / GI clamp including bend, elbow , socket etc complete | 30 | RM | |
| 59 | 59 | Material and Labour for fixing of designer eaves board fixed with end of purlins with mild steel plate including necessary welding, scaffolding etc completein all as specified and as directed. | 10 | Sqm | |
| 60 | 60 | S & F designer venitian blinds vertical type 100mm wide slats made out of fabric cloth of approved shade fixed as per the instructions of manufacturers and all as specified by Campus Supdt. Make: Hanterdagluas/ Vista select/neha printed and exclusive shades. | 50 | Sqm | |
| 61 | 61 | M & L for granite of any type work (table rubbed and polished) in steps, jambs, pillars, window cills, plate forms in cement mortar (1:4) incldg pointing in white cement (1:2) using marble dust with admixture of pigment to match with sheds of granite 16-18 mm including double moulding complete all as directed. | 30 | Sqm | |
| 62 | 62 | M & L for granite of any type work (table rubbed and polished) for wall lining(veneerimg to wall) 12mm th incement mortar (1:3) incldg pointing in white cement (1:2) using marble dust with admixture of pigment to match with sheds of granite 16-18 mm thick. | 8 | Sqm | |
| 63 | 63 | M&L granite ( of any type) tiles 16-18 mm thick machine cut, polished laid over top of cupboard/slab/steps/platforms fixed with adhesive of approved make all as specified | 4 | Sqm | |
| 64 | 64 | M&L in repair 18-19 mm thick MDF Board exterior grade pre laminated one side with decorative choice and other side balancing white lamination fixed with screws as in cupboard and cupboard shutters including leaping/beading (polished) all as specified | 50 | Sqm | |
| 65 | 65 | M&L for plain fillets,square rectangular or triangular in section secured with nails or brads n,exc 3 Sq cm. | 30 | RM | |
| 66 | 66 | S&F 75mm barrel tower bolts,with cast or sheet and rolled or cast bolts. | 15 | Nos | |
| 67 | 67 | S&F hinges piano type MS Bright flush 30 mm width of flaps. | 15 | RM | |
| 68 | 68 | S&F 100mm door handle brass,cast type,polished bright | 15 | Nos | |
| 69 | 69 | S&F 4 lever brass cup board lock grade I, 65 mm | 15 | Nos | |
| 70 | 70 | S&F harrison rails,aluminium alloyanodised with fixing brackets, stops, rollers etc. | 10 | RM | |
| 71 | 71 | S&F cup board knobs fixed with nut, screw and washer of mild steel bright finished | 20 | Each | |
| 72 | 72 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) completete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, lights fitting etc remiving materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floor etc | 30 | PER POINT | |
| 73 | 73 | Material and labour for point wiring with 1.5 Sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 volts drawn through and including rigid non metallic surface conduit medium grade ISI marked minimum 20mm dia and its accessories complete alongwith 1.5 Sqmm cable but in green colour as continuous earthing wire and connnecting to common earth duy completely concealed. Surface in walls/ceiling roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations, fan regulators etc, as required with 3mm thick plastic laminated sheet top cover all as specified and directed for the following points.\n(a) One light point controlled by one modular switch | 28 | POINT | |
| 74 | 74 | Material and labour for point wiring with 1.5 Sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 volts drawn through and including rigid non metallic surface conduit medium grade ISI marked minimum 20mm dia and its accessories complete alongwith 1.5 Sqmm cable but in green colour as continuous earthing wire and connnecting to common earth duy completely concealed. Surface in walls/ceiling roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations, fan regulators etc, as required with 3mm thick plastic laminated sheet top cover all as specified and directed for the following points.\n(b) One ceiling /exhaust fan point controlled by one modular switch | 2 | POINT | |
| 75 | 75 | Material and labour for point wiring with 1.5 Sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 volts drawn through and including rigid non metallic surface conduit medium grade ISI marked minimum 20mm dia and its accessories complete alongwith 1.5 Sqmm cable but in green colour as continuous earthing wire and connnecting to common earth duy completely concealed. Surface in walls/ceiling roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for mounting switches, switch socket combinations, fan regulators etc, as required with 3mm thick plastic laminated sheet top cover all as specified and directed for the following points.\n(c) One three pin modular socket out let 5 Amp on independents board complete | 10 | POINT | |
| 76 | 76 | Material and labour for point wiring with 4.00 sqmm (Nominal Area) FRLS PVC insulated sheathed multi stranded copper conductor, 1100 volts drawn through and including rigid non metallic surface conduit medium grade ISI marked minimum 20mm size and its accessories complete alongwith 4.00 sqmm cable but in green colour as continuous earthing wire and connnecting to common earth duly completely concealed. surface in walls/ceiling roofs with and including 1.2mm thick MS sheet terminal boxes duly fabricated flush mounting in the wall for one 3 pin socket out let 15 Amps on independent board with 3mm thick plastic laminated sheet top cover all as specified and directed Note : Necessary PVC, rigid, concealed type junction boxes for identifying junction as required on site directed by Campus Supdt for point wiring with PVC dummy plates shall to be included in quoted. | 10 | Point | |
| 77 | 77 | Supply and fix modular switch 1 way 6 Amp, 240 Volt. Make : Anchor/Havells | 30 | Each | |
| 78 | 78 | Supply and fix modular switch 1 way 16 Amp, 240 Volt. Make : Anchor/Havells | 10 | Each | |
| 79 | 79 | Material and labour ceiling rose surface type bakelite 65x50mm with three terminals complete all as directed. | 30 | Each | |
| 80 | 80 | Supply and fix modular socket outlet 6A 2/3 Pin with switch complete all as directed. | 10 | Each | |
| 81 | 81 | Supply and fix modular socket outlet 16A 2/3 pin with switch complete all as directed. | 10 | Each | |
| 82 | 82 | Supply and fix modular white cover plate with frame 4 module or as per ground reqmt complete all as directed. | 24 | Each | |
| 83 | 83 | Supply and fix modular white cover plate with frame 6 module or as per ground reqmt complete all as directed. | 3 | Each | |
| 84 | 84 | Supply and fix LED holder for 12 watt complete all as directed. | 2 | Each | |
| 85 | 85 | Supply and fix LED tube light fittings 1x20w 230V energy efficient fittings decorative type complete including housing all pre wired with high efficiency electronic driver complete fixed to wall/ceiling including connection by flexible PVC cable with standred copper conductor from ceiling rose to connector of the fittings including LED tube complete all as specified and directed. Make : Havells / Bajaj / Syska | 30 | Each | |
| 86 | 86 | Supply and fix sheet factory made, powder coated MCB DB with bus bar 200 Amps Neutral link, earth bar, double door SPN 8 way 230 Volts all as directed. Make Havells/Legrand | 1 | Each | |
| 87 | 87 | Supply and fix miniature circuit breaker (MCBs) MCCB of following capacity \n(a) MCB Single pole 240 Volts 6-32 Amps. Make Havells/Legrand | 3 | EACH | |
| 88 | 88 | Supply and fix miniature circuit breaker (MCBs) MCCB of following capacity \n(b) MCB SPN 240 Volts 0-32 Amps. Make Havells/Legrand | 6 | EACH | |
| 89 | 89 | Supply and fix LED bulb for 18 watt complete all as directed. Make : Havells/Syska | 2 | Nos | |
| 90 | 90 | Supply and fix exhaust fan with for protection when not in use silent operation rust proof body and blades with fixing arrangements of size 300mm seeep 1400 rpm. Make : Havells/Bajaj | 2 | Nos | |
| 91 | 91 | Earthing with copper plate 610x610x3mm size having weight of 9.84kg and 1 No 25x5mm copper steel (3.2m long) and 1 No 6 sqmm PVC insulated stranded copper wire (054 Mtr long) including supplying and fixing 15mm dia GI pipe production to be filled with bitumen partly under the ground level and partly above the ground level to an average depth of 3.65mtr below the ground level and restoring the surface duly rammed incluidng providing 3 Mtr long 25mm dia GI pipe for periodic treatment including providing masonary enclusure on the top of earth electrode of overall size 86.36x86.36x46cm deep below ground level complete cement work with brick and cement mortar, inside CI hinged inspection cover size 36.56x36.56cm with locking arrangement, galvanised iron reducer and treatment of soil by using salt and charcoal. | 1 | Nos |
AI Tender Summary
Tender Timeline
Oct 30, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedNov 12, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedNov 15, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender