Military Engineer Services-MES has published Repair /Maintenance Of Street Lights , Garden Light , High Mast Light , Street Light Controller Etc At Irde And Deal Under Ge ( I ) Rnd Dehradun. Submission Date for this Tender is 09-11-2019. Tube Light Tenders in DEHRADUN Uttarakhand. Bidders can get complete Tender details and download the document.
| NAME OF WORK : REPAIR /MAINTENANCE OF STREET LIGHTS, GARDEN LIGHT , HIGH MAST LIGHT,STREET LIGHT CONTROLLER ETC AT IRDE AND DEAL UNDER GE (I) R&D DEHRADUN | |||||
|---|---|---|---|---|---|
| Sl. No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes etc. including removing cable protection covers/ bricks complete all as specified and directed. \nNotes : (i) Excavation shall be made carefully in order to avoid damage of existing cables and brick protection.\n(ii) The excavation work may be carried out in short lengths for locating fault in under ground cables at different locations | 100 | Cum | |
| 2 | 2 | M&L for Returning, filling in, including spreading leveling, watering and well ramming the excavated soil in layers not exceeding 25 cm thick complete all as specified and directed. | 90 | Cum | |
| 3 | 3 | M&L for Removal of surplus excavated soil to a distance not exceeding 50 Mtr distance and depositing as directed at a level not exceeding 1.5 mtr above starting point complete all as specified and directed. | 11 | Cum | |
| 4 | 4 | Material & labour for sand filling with clean dry fine sand unwashed including gently punning around cables in trenches/ducts for cable protection complete all as specified and directed . | 46 | Cum | |
| 5 | 5 | M&L for old size sub class `B` bricks, kiln burnt, as in cable protection laid flat with axis of brick perpendicular to the axis of the cable complete all as specified and directed . | 4461 | Each | |
| 6 | 6 | Fixing / laying only old bricks as in cable protection laid flat with axis of brick perpendicular to the axis of the cable complete all as specified and directed . Note :- Old Bricks retrived under item No.01 herein above shall be reused. | 496 | Each | |
| 7 | 7 | Disconnecting and taking out old unserviceable GI pipe and Supplying, laying & jointing GI water tubing, 50 mm bore, light grade as in sleeving etc laid in trenches / pole post etc. complete all as specified and directed . Make of pipe TATA / Jindal / Swastik / Prakash / BST or any other ISI marked make approved by GE. | 6 | Rm | |
| 8 | 8 | Disconnecting and taking out old existing unserviceable/ non- functional LT Cable of any size , description and in any position from trench/duct/pipe/ pole etc complete and Supplying, laying, jointing & testing XLPE insulated PVC sheathed (heavy duty) armoured cable with aluminium conductor for working voltage upto 1100 volts having cross sectional area 16 qmm 4 core of cables conforming to IS 7098 Part-I - 1988 laid in trenches/ fixed on pole/ passes through pipe complete all as specified and directed. (Note- earth work,sand cushioning,pipe, clamps and brick protection shall be measured and paid separetly). | 400 | Rm | |
| 9 | 9 | Supply and laying XLPE insulated PVC sheathed (heavy duty) armoured cable with aluminium conductor for working voltage upto 1100 volts having cross sectional area 6 qmm 2 core of cables conforming to IS complete all as specified and directed. | 200 | Rm | |
| 10 | 10 | Labour only for checking the serviceability of the different spares / components / parts of security light fittings/post top lantern light fittings (LED, HPSV, Metal Halide, flood light fittings etc, any wattage/capacity) of any description and fixed in any position, replacement of un-serviceable/damaged/ broken part(s) either in single or in combination, re-assembling the fittings and making the light fittings serviceable, fixing the fittings in position, connecting to electric supply and its testing on installation complete all as specified and directed (including mentioned in Srl No. 10.01 and 10.02 here in after) | 152 | Each Job | |
| 11 | 10.01 | NOTES FOR SCH `A’ ITEM NO 10.00:-\n(i) Replacement of parts i.e lamps, choke, Igniter, Condenser, Holder, covers etc for HPMV/HPSV/MH/Flood light fittings any wattage & capacity, if any required at site, (ii) Necessary T&P i.e. ladder, tools etc required for checking and making the light fittings in serviceable conditions, its fixing in position and testing shall be arranged by the contractor at his own cost for checking and fixing of street light fittings/security light fittings of any description on poles / on walls / on pillars etc i.e. in any position at site. | |||
| 12 | 10.02 | NOTES FOR SCH `A’ ITEM NO 10.00 contd :- (iii) Required screws, insulating tapes, internal wiring wire and other minor items excluding the required spares parts for repairing and making the street light fittings/security light fittings in serviceable condition, will be arranged & supplied by the contractor and cost of which is deemed to be included in the rates quoted by the contractor in above respective item. (iv) Contractor shall be paid only one time the labour charges quoted above in Schedule `A' items for a particular fitting repaired irrespective of the number of times labour and resources arranged by him to check the serviceability of the fittings and replacement of unserviceable / defective parts in order to maintain the fittings in serviceable/working condition. \n(v) Contractor’s quoted rates for this item is deemed to include for inspection/checking the serviceability of the fittings in position or by taking down as per site requirement, removing the damaged unserviceable / broken parts, fixing the new parts as required, fixing the fittings in same position or the other, connecting the fittings with electric source and testing of fittings as directed. | |||
| 13 | 11 | Supply only the following parts for LED light fittings, dismantled/fixed covered under Sch `A` item No 10.00 here in above complete all as specified and directed.\nNotes:- (i) Fixing element of these items deemed to be included in the rate quoted by contractor for sch item No 10.00. (ii) sphere parts/ items shall be of make-Crompton greaves/ philips/ havells/C&S and as approved by GE or suitable for existing fittings. | |||
| 14 | 11.01 | Driver suitable for 45/48 watt LED light fittings. | 10 | Each | |
| 15 | 11.02 | Driver suitable for 60 watt LED light fittings. | 10 | Each | |
| 16 | 11.03 | Driver suitable for 90 watt LED light fittings. | 10 | Each | |
| 17 | 11.04 | Driver suitable for 100/120/150 watt LED light fittings. | 5 | Each | |
| 18 | 11.05 | Safety protection devices (SPD) . | 5 | Each | |
| 19 | 12 | Taking down existing unserviceable bracket complete and S&F 40 mm dia GI light grade pipe bracket 1.50 m long bent to shape by cutting & welding as required & directed and fixed to pole/wall with two No,s of FI clamps 40x5 mm to be tightened with bolts, nut and washers and including painted with two coat of aluminium paint over a coat of red oxide primer complete all as specified and directed. | 4 | Each Job | |
| 20 | 13 | Disconnecting and taking out existing unserviceable light fitting of any description and in any position on poles and S&F 35 watts LED Post top of lantern complete accessories to be fixed on pole/ wall and accessories including connecting the fitting to control switch box at the bottom of the pole with using 2.5 Sqmm two single core PVC insulated and unsheathed copper conductor cable complete all as specified and directed . (Make-Havells cat part No- CORALPT25W LED 757 PSYMTOPC or equivalent model of Bajaj / Crompton Greaves/Philips/ C&S). | 14 | Each | |
| 21 | 14 | Disconnecting and taking out existing unserviceable light fitting of any description and in any position on poles and S&F 20 watts LED Post top of lantern complete accessories to be fixed on pole/ wall and accessories including connecting the fitting to control switch box at the bottom of the pole with using 2.5 Sqmm two single core PVC insulated and unsheathed copper conductor cable complete all as specified and directed . \n(Make-Crompton cat part No- LPTH-20-CDL or equivalent model of Bajaj / Havells/Philips/ C&S). | 21 | Each | |
| 22 | 15 | S&F galvanised iron tubing 50 mm bore medium grade of 2 metre each on vertical position fixed in PCC foundation including fixing of one number Post top Lantern on top heavy duty welded or screued tightly with GI pipe of 50 mm dia complete including two coat of powder coated paint of approved shade over one coat of red oxide primer including affix 50 mm dia sticker on GI pipe duly printed as "MES number" complete all as specified and directed. | 21 | Each Job | |
| 23 | 16 | Excavation in post holes (or similar holes) each n. exc. 0.5 cum in soft/loose soil and getting out returning filling in and ramming earth or broken rubble mixed with eareth around in layers not exc. 25 cm watering and removing surplus soil to a distance n. exc 50 m and making good surface complete all as specified and directed. | 21 | Each | |
| 24 | 17 | M & L for cement concrete ( 1:3:6 ) type C-2 (using 40 mm graded stone aggregate) as in foundation and mass filling etc including necessary form work complete all as specified and directed. | 12 | Cum | |
| 25 | 18 | Disconnecting and taking out existing unserviceable MS boxes of any description and in any position on poles or fixed in the plinth of poles and supplying and fixing in position new Pole box made of thermoplastic Polycarbonate having IP65/IP66 degree of protection (shock proof, dust proof, jet water proof and acid resistive). The gasket should be internally embedded, and made of Polyeutherene. The boxes shall be tested as per IEC 60670-2/ 60670-22. The boxes shall have self threaded holes & provision for mounting din rail. The lid should be hinged type with sealing screw. The screw should be of stainless steel so that there is no corrosion. The boxes should withstand temperature of -40c to +120c. The glow wire test should be conducted at 960 c or 750 c and material should be flame retardant & self extinguishing. UL subject 94, V-0. The boxes should be free from toxic substances like hal ogen and silicon. The boxes should have suitable pre-moulded knock out /or plan wall depending on requirement. Box dimension shall not be less than 200 X 160 X98 MM (LXBXH). Box shall be suitable for 16/25Sqmm cables including one no. MCB SP 230 volts 5 amps of make Havells/MDS and connecting the bus bars to cables with using suitable GI nut, bolts and washers and aluminum lugs etc fixed on pole using 30x5mm FI clamps,nuts,bolts & washers complete all as specified and directed. Make: Hensel/GE/Legrand. | 33 | Each | |
| 26 | 19 | M & L for cutting chases in hard standing road/path/drain etc for passing cables/pipes etc. size of cutting 100mm wide and 200mm deep and removing the excavated materials and disposal at 50 metre distance and making good the cutting after the pipe and cables are laid with PCC 1:3:6 type C-1 using 20mm graded stone aggregates complete all as specified and directed. | 6 | RM | |
| 27 | 20 | Taking down existing old rusted electric pole of any description and Supply, erecting and fixing in true vertical position, steel tubular swaged pole (410 SP – 31), 9 mtr long, complete conforming to IS : 2713 (Part-I & III) 1980 with cast iron base plate, pole cap / finial taper plug, bolts, nuts and washers, welded reduced section and longitudinal weld throughout entire length of pole with and including 2 coats of black bituminous paint externally upto planting depth and remaining exterior portion of pole finished with one coat of red oxide primer including earth work in excavation, removal, returning filling in, PCC 1:3:6 type C-2 using 40mm graded stone aggregates in foundation, PCC 1:2:4 type B-1 using 20mm graded stone aggregates in coping complete all as specified and directed. | 1 | Each Job | |
| 28 | 21 | M & L for making holes in electric / street light poles of any description, shape and height, by means of drilling machine and drawing of 1.5 sqmm x 3 core cable through the hole from junction box to the hole on top of pole near the street light fitting complete with all electric connection complete all as specified and directed. | 20 | Each Job | |
| 29 | 22 | Supply and fixing in repair Multifunctional digital time switch (Astrorex D21), cat no 4QTBW- 649914, supply voltage 220-240 volts AC 50 Hz AC. make : Legrand or equivalent make of L&T . | 1 | Each | |
| 30 | 23 | Supply and fixing in repair Power contractor 3 pole series, 415 volts, 50 Hz, 63 amps open with standard coil voltage 240/220 volts , of make : Cat No: 412550 of Legrand/ Seimens/ Sneider | 1 | Each | |
| 31 | 24 | Disconnecting and taking out existing Flood light fitting of any description and in any position on High mast 16.0/12.0 mtr hight poles and Supply, fixing & testing 120W LED flood light with pressure die-cast aluminium housing, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed.\n(Make- Havells Cat No. JETAPROPLUSFL120W LED 757 LTG or equivalent model of make/Philips/Crompton). \nNote : GI pipe bracket and clamps if required shall be measured and paid separately. | 32 | Each Job | |
| 32 | 25 | Disconnecting and taking out existing Street light fitting of any description and in any position on Street light poles and Supply, fixing & testing 45W LED street light IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed.\n(Make- Crompton Cat No. LSTP-45-CDL or equivalent model of make /Philips/ Havells). \nNote : GI pipe bracket and clamps if required shall be measured and paid separately. | 23 | Each Job | |
| 33 | 26 | Disconnecting and taking out existing Street light fitting of any description and in any position on Street light poles and Supply, fixing & testing 60W LED street light IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed.\n(Make- Havells cat no LHETBXU7PA6J060 or equivalent model of make crompton /Philips). \nNote : GI pipe bracket and clamps if required shall be measured and paid separately. | 26 | Each Job | |
| 34 | 27 | Disconnecting and taking out existing Street light fitting of any description and in any position on Street light poles and Supply, fixing & testing 90W LED street light IP66 Powder coated pressure die cast aluminium High power LED street light with heat resistant toughened glass with lens, complete with all accessories duly prewired and suitable fixing arragement for mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed.\n(Make- Havells cat no LHETBXU7PA6J090 or equivalent model of make crompton/Philips). \nNote : GI pipe bracket and clamps if required shall be measured and paid separately. | 10 | Each Job | |
| 35 | 28 | Disconnecting and taking out existing Roadway light fitting of any description and in any position on Walls/poles and Supply, fixing & testing 15W LED street light Robust PDC housing with poly carbonate cover with high impact resistance,15W-1500 lumens with efficacy of 100 lumens/watt at system level, ingress protection of IP65, pf-0.9 & with input resistanct i.e, IK 09 surge protectin upto 4KV, compiled with IS 10322 CCT is greater than 5000K, complete with all accessories duly prewired, supply and fixing the bracket of 20 mm dia 60 cm long GI pipe light grade bent to shape and including MS FI clamp of 20x3 mm nut and bolts and connected with flexible cable 3 core copper conductor 0.5sqmm up to ceiling rose Complete.mounting on existing MS frame bracket including connecting the fitting complete all as specified and directed.\n(Make- Havells cat pt No-LHEETBXU7IA6S015/, C&S cat pt No-LTESS15WLED or equivalent model of make crompton/GE). \nNote : GI pipe bracket and clamps if required shall be measured and paid separately. | 20 | Each Job | |
| 36 | 29 | Material and labour for point wiring using 1.5 Sqmm size multi stranded copper conductor,unsheathed,FR cable ( Phase-Red, Neutral- Black) , 1100 volts grade confirming to IS- 694 ,drawn in and including rigid concealed PVC conduit 20 mm dia (Medium grade) ISI marked ,ivory colour on walls/ floors/ ceiling and connecting to modular boxes not less than 1.12 mm cover with 3 mm thick phenolic laminated white sheet cover for mounting switches,sockets, fan regulators etc including 1.5 sqmm PVC insulated unsheathed copper cable green in colour as contineous earth continuity conductor and connecting to earth dolly, cutting chases to walls/ floors/ ceiling and repairing with match to existing surface after work , for one light/ fan point controlled by one switch, complete all as specified and as directed. | 20 | Each Point | |
| 37 | 30 | Taking out of old existing unserviceable switch board and box any description and in any position and Supply & fixing water tight & dust proof enclosers IP 55 ,surface mounting for 6 Amp switch complete all as specified and directed. Make- C&S cat part No-CG 26016 W (enclosure) and CS 20113 (switch) or equavalent in Havells/Legrand as approved by GE. | 20 | Each | |
| 38 | 31 | Material and labour for cleaning and preparation of all existing steel surfaces of straight Electric/ steel tubular poles 9/11 mtrs long for painting including mild steel cross arms, clamps and street light brackets,protection pipe, MS boxes etc and applying Two coat of aluminium paint all round the exposed steel surfaces of existing steel tubular poles of any description and in any position above the height of 1.50 mtr from the plinth of the pole and applying one coat of synthetic enameled paint of different colours in strips of 150mm width upto the height 1.5 mtr from the plinth of pole complete all as specified and directed. | 53 | Each Job | |
| 39 | 32 | M & L for re-Writing letters or figures (Black, roman, Indian) for electric/ street light pole Nos on existing poles with stencil out with black colour including fixing red colour radium of 80 mm hight arround the radius of pole complete all as specified and directed. | 65 | Each | |
| 40 | 33 | Prunning of tree branches or cutting of tree branches where required for proper clearence to street light poles/ lines complete all as specified and directed. | 230 | Each Span | |
| 41 | 34 | Taking down old existing unserviceable Highbay light fittings from poles etc and supply and fixing of new LED highbay light fittings 100 watts complete all as specified and directed. Make- C&S cat part No-LTEHB120WHPLED/LS or equivalent in Crompton/Havells as approved by GE. | 10 | Each | |
| 42 | 35 | Supply and fixed in repair Battery 12 v, 40 AH ,for solar street light system Complete all as specified and directed.Make-Jilco/Havells/ Exide. as approved by GE. | 1 | Each | |
| 43 | 36 | Supply and fixed in repair solar street light fitting 9 watt solar light system Complete all as specified and directed.Make-Jilco/Havells/ Exide. as approved by GE. | 1 | Each | |
| 44 | 37 | S&F integral LED Solar street light fight pressure die cast aluminium housing (LM6 Alloy) reliable & robust construction, minimum 2000 lumens with system efficacy of 175 lumens per watt SMD LEDs with PMMA Lens plat, external built proper heat sinks and toughen glass/PC ensuring IP65 & Life of LED luminaries engine should be 50000hrs along with built in high efficiency MPPT charge controller & driver along with Life PO4 battery chemistry and high effect reliable PV module suitable for even harsh conditions CCT >5000, CRI 70, The fixture should have designed for street light application and should have flexible angle of mounting from 0-15 degree for diverse geographical condition. Factory configured LED load and PIR sensor dimming for optimum of autonomy uses up to 24 hrs. System should have smart self-diagnostic feature for indicating battery charging, cut off and fault if any. Company logo shall be engraved to avoid any distrusts. Complete system should have minimum warrantee of 36 month complete all as specified and directed. | 3 | Each | |
| 45 | 38 | M&L for monkey cage frame work fabricated out of such as angle iron and iron strip etc with ends of iron strips welded / shouldred/ riveted and fixed to pole with nut bolt and washers etc for post top tantern light fitting complete all as specified and directed. | 300 | Kg |
Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
