Construction Of Boys Common Room In Shishu Ananta Mahavidyalaya , Balipatna Under Csr
Tender Value
18.19 Lakhs
Estimated cost
Bid Submission
30 Sep 2019
0 days left
EMD
22800
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Balipatna → Odisha
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Construction Of Boys Common Room In Shishu Ananta Mahavidyalaya , Balipatna Under Csr
BOQ
| Name of the Work | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m,disposed earth to be levelled and neatly dressed. \nAll kinds of soil | BI01010001010000000000000515BI0100001113 | 43.38 | Cum |
| 2 | 2 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. | 28.92 | cum | |
| 3 | 3 | Supplying and filling in plinth with local sand under floors, including watering, ramming, consolidating and dressing complete. | 44.23 | Cum | |
| 4 | 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : \n1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). | 13.17 | cum | |
| 5 | 5 | Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering complete as per the direction of Engineer-in-charge 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) | 14.1 | Cum | |
| 6 | 6 | Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement : Encasing rolled steel section in grillages with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 12.5mm nominal size)including centering and shuttering but excluding cost of expanded metal and hangers. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) | 4.5 | Cum | |
| 7 | 7 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size). | 23.86 | Cum | |
| 8 | 8 | Centering and shuttering including strutting, propping etc. and removal of form for : \nFoundations, footings, bases of columns, etc. for mass concrete. | 26.6 | Sqm | |
| 9 | 9 | Centering and shuttering including strutting, propping etc. and removal of form for : \nSuspended floors, roofs, landings, balconies and access platform. | 105.35 | Sqm | |
| 10 | 10 | Centering and shuttering including strutting, propping etc. and removal of form for : \nLintels, beams, plinth beams, girders, bressumers and cantilevers. | 76.46 | Sqm | |
| 11 | 11 | Centering and shuttering including strutting, propping etc. and removal of form for : \nColumns, Pillars, Piers, Abutments, Posts and Struts. | 29.25 | Sqm | |
| 12 | 12 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level. \nThermo-Mechanically Treated bars. | 1128 | Kg | |
| 13 | 13 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. \nThermo-Mechanically Treated bars. | 2722.4 | Kg | |
| 14 | 14 | Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:\nCement mortar 1:6 (1 cement : 6 coarse sand) | 4.65 | Cum | |
| 15 | 15 | Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size). | 11.63 | Sqm | |
| 16 | 16 | Brick work with non modular fly ash F.P.S. (non modular) brick of class designation 7.5 in superstructure above plinth level up to floor five level in : Cement mortar 1:6 (1 cement : 6 coarse sand) | 23.62 | Cum | |
| 17 | 17 | Half brick masonry with non modular fly ash bricks of class designation 10, conformingio IS :12894, in super structure above plinth and upto floor V level.\nCement mortar 1 : 4 (1 cement : 4 coarse sand) | 41.87 | Sqm | |
| 18 | 18 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. | 31.44 | Sqm | |
| 19 | 19 | Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. \nFixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) | 80 | kg | |
| 20 | 20 | Providing and fixing M.S. fan clamp type I or II of 16 mm dia M.S. bar, bent to shape with hooked ends in R.C.C. slabs or beams during laying, including painting the exposed portion of loop, all as per standard design complete. | 8 | Each | |
| 21 | 21 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1stclass hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters : \n35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. | 8 | Sqm | |
| 22 | 22 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). | 8 | Sqm | |
| 23 | 23 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :\nFor fixed portion\nPowder coated aluminium (minimum thickness of powder coating 50 micron) | 33.6 | Kg | |
| 24 | 24 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :\nFor shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)\nPowder coated aluminium (minimum thickness of powder coating 50 micron) | 40.32 | Kg | |
| 25 | 25 | Providing and fixing 12 mm thick prelaminated particle board flatpressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windowsshutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge.\nPre-laminated particle board with decorative lamination on one side and balancing lamination on other side | 13.44 | sqm | |
| 26 | 26 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :\n300x16 mm | 8 | each | |
| 27 | 27 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :\n200x10 mm | 8 | each | |
| 28 | 28 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. \nFixed to steel windows by welding. | 161 | Kg | |
| 29 | 29 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.\nSize of Tile 600x600 mm | 87.75 | Sqm | |
| 30 | 30 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.\nSize of Tile 600x600 mm | 7.2 | Sqm | |
| 31 | 31 | 12 mm cement plaster of mix : \n1:6(1 cement: 6 fine sand) | 343.09 | Sqm | |
| 32 | 32 | 6 mm cement plaster of mix:\n1:3 (1 cement : 3 fine sand) | 156.12 | Sqm | |
| 33 | 33 | White washing with lime to give an even shade: New work (three or more coats) | 101.71 | Sqm | |
| 34 | 34 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade \nNew work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). | 207.83 | Sqm | |
| 35 | 35 | Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade \nNew work (two or more coats) over and including water thinnable priming coat with cement primer. | 133.08 | Sqm | |
| 36 | 36 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. \n110 mm diameter | 17.75 | metre | |
| 37 | 37 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:\n1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size) | 4.84 | Cum | |
| 38 | 38 | Supply of 1x 18 W LED Tubelight complete with ceiling mounted fixture with all accessories | 12 | Each | |
| 39 | 39 | Installation, testing & commissioning of 1x18W LED tubelight fitting with all accessories and tube directly on wall/ceiling including connection with 1.5 sq mm FR PVC insulated copper conductor single core cable & earthing etc. as required | 12 | Each | |
| 40 | 40 | Supply of high speed ( min 350 rpm) 1200 mm sweep ceiling fan, including the down rods of standard length (upto 30 cm) including connections etc. as required | 8 | Each | |
| 41 | 41 | Installation, testing and commissioning of ceiling fan including wiring the down rods of standard length (upto 30 cm) with 1.5 sqmm FR PVC insulated, copper conductor, single core cable etc. as required. | 8 | Each | |
| 42 | 42 | Supplying and fixing stepped type electronic fan regulator on the existing switch box including connections etc. as required. | 8 | Each | |
| 43 | 43 | Supplying and fixing of 3pin, 5 Amps. Ceiling rose on the existing junction box/metal box including connection etc as required. | 20 | Each | |
| 44 | 44 | Supplying and fixing of metal box of 75mm X 75mm X 60mm deep size on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required | 20 | Each | |
| 45 | 45 | Point wiring of light/ceiling fan/call bell/5A socket/exhaust points with 1.5 sq. mm FR PVC insulated copper conductor single core cable in surface/recess through medium class PVC conduit with 5A piano type switch, phenolic laminated sheet, suitable size MS box of average run of 3 meters and earthing the point with 1.5 sq mm FR PVC insulated copper conductor single core cable etc. as required. | 22 | Each | |
| 46 | 46 | Supplying and fixing of 3 pin 5/6 amp socket outlet piano type on the existing junction box / metal box including connection etc. as required. | 2 | Each | |
| 47 | 47 | Supplying and fixing of metal box of 180 mmx100mmn x 60 mm deep (nominal size) on surface or in recess with suitable size of phenolic sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps.socket outlet and 15/16 amps. piano type switch connection, painting etc. as required. | 1 | Each | |
| 48 | 48 | Wiring for power plug with 2*4 sq. mm FR PVC insulated copper conductor single core cable in surface / recess through medium class PVC conduit along with 1 no. 4 sq. mm. FR PVC insulated copper conductor single core cable for loop earthing including connection etc as required. | 20 | Meter | |
| 49 | 49 | Wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required.\n2 X 2.5 sqmm. + 1 X 2.5 sqmm. Earth wire | BI01010001010000000000000515BI0100001126 | 20 | Meter |
| 50 | 50 | Total impact of GST for the purpose of CTC | BI01010001010000000000000515BI0100001129 | 1 | Nos |
AI Tender Summary
Tender Timeline
Sep 16, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 01, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender