| 1 | 1 | Dismantling of wall or ceiling boards any thickness , including cover fillets | | 250 | Sqm |
|---|
| 2 | 2 | Dismantling boarding any description fixed inn any position with nails | | 18 | Sqm |
|---|
| 3 | 3 | Dismantling plain or corrugated steel sheeting, any gauge, thickness including nainital or similar pattern roof coverings any thickness | | 90 | Sqm |
|---|
| 4 | 4 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) including removing rubbish off the premises complete all as specified and directed. | | 67.2 | Cum |
|---|
| 5 | 5 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but not exc 4 sqm each complete all as specified and directed. | | 6 | Each |
|---|
| 6 | 6 | Taking down chowkats or frames with shutters (without taking off shutters from the frames) area not exc 1.50 Sqm.(in lieu of steel windows) | | 9 | Each |
|---|
| 7 | 7 | M&L for 40 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in floorings, including finishing the surface even and smooth using extra cement. | | 475 | Sqm |
|---|
| 8 | 8 | M & L for 25 mm thick PCC (1:2:4), type B-1 (using 20 mm graded stone aggregate) as in sub base to receive floor tiles. | | 95 | Sqm |
|---|
| 9 | 9 | M & L for screed bed or bedding layers 15 mm thick in CM 1:4 for laying floor tiles. | | 95 | Sqm |
|---|
| 10 | 10 | M & L for non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular),area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in r coloured cement to match. | | 95 | Sqm |
|---|
| 11 | 11 | M & L for 50 mm thick II nd class Hard wood clean sawn boarding with butt joints fixed with nails in any situation. | | 18 | Sqm |
|---|
| 12 | 12 | M & L for preparation of wood or wood base materials of any description and girth not otherwise described and treated with two coats of creosote oil | | 18 | Sqm |
|---|
| 13 | 13 | M & L for 4 mm thick ply wood, grade BWR, type BB, fixed with nails to timber frame work on ceiling surfaces. | | 90 | Sqm |
|---|
| 14 | 14 | M & L for 2 nd class Hard wood plain fillets, square, rectangular or triangular in section,wrought, secured with nails or brads, sectional area exc 3 but n.exc 6 sq.cm. | | 160 | RM |
|---|
| 15 | 15 | M & L for 4 mm thick ply wood, grade BWR, type BB, fixed with nails to timber frame work on wall surfaces.\n\n | | 160 | Sqm |
|---|
| 16 | 16 | M&L for preparation of new wooden surfaces of any description, not other wise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. | | 258 | Sqm |
|---|
| 17 | 17 | M&L Second class clean sawn hard wood in scantlings in framed work. | | 0.36 | Cum |
|---|
| 18 | 18 | S&F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugation side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws and washers, in roofs, walls etc. with grade of zinc coating 120 gsm. | | 80 | Sqm |
|---|
| 19 | 19 | S&F 0.80 mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings ( length and girth as fixed) with grade of zinc coating 120 gsm. | | 10 | Sqm |
|---|
| 20 | 20 | M&L for two coat of synthetic enamel roof paint over new zinc (or galvanised ) surfaces to receive painting, by coating with mordant solution including washing and cleaning etc. of any description, not otherwise described, over 10 cm width or girth. | | 102 | Sqm |
|---|
| 21 | 21 | S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. | | 0.78 | Cum |
|---|
| 22 | 22 | S&F 35 mm thick 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed. | | 11 | Sqm |
|---|
| 23 | 23 | S&F 30 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc ; sizes of members of shutters as specified in SSR Part-I, section-8, clause 8.24(a). | | 16 | Sqm |
|---|
| 24 | 24 | S&F MS window guard bars, window frames etc articles confirming to Fe 410-0 or Fe 310-0. | | 60 | Kg |
|---|
| 25 | 25 | S&F fixed galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of apperture 1.18 mm and fixed with tinned tacks or galvanised wire staples. | | 5 | Sqm |
|---|
| 26 | 26 | S & F sheet glass 3mm thick ordinary quality and glazing with oil putty/wooden beads in squares n exc 0.50 Sqm in each pane. | | 4.5 | Sqm |
|---|
| 27 | 27 | S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed. | | 18 | Each |
|---|
| 28 | 28 | S&F 150mm long aluminium anodized, barrel tower bolts extruded section. | | 12 | Each |
|---|
| 29 | 29 | S & F 150mm size extruded aluminium alloy handles, fabricated type anodised | | 12 | Each |
|---|
| 30 | 30 | S&F 100mm size extruded aluminium alloy handles, fabricated type, anodised. handle fabricated type (Make :- Crown or equivalent) | | 36 | Each |
|---|
| 31 | 31 | S & F 75 mm size mild steel butt hinges medium weight cold rolled and fixed. | | 108 | Each |
|---|
| 32 | 32 | S&F 100mm long aluminium anodized, barrel tower bolt extruded section. (Make : Crown or equivalent) | | 72 | Each |
|---|
| 33 | 33 | S&F 300 mm long Brass sliding door bolt with sand or Die cast brass hasp, staple (bolt type) and fixing bolt, with rolled or drawn brass and fixed. | | 6 | Each |
|---|
| 34 | 34 | S&F pre coated mild steel floor door stopper ,tongue anodized 140mm length including vulcanised rubber piece | | 6 | Each |
|---|
| 35 | 35 | M & L PCC 1:3:6 type C1, (using 20mm graded stone aggregate) as in surface channels and drains . | | 123.5 | Cum |
|---|
| 36 | 36 | Extra for forming fair finishing drain or channels 30 cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc. | | 324 | RM |
|---|
| 37 | 37 | M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded stone aggregate as in plinth protection surface finished even and smooth using with extra cement | | 28 | Sqm |
|---|
| 38 | 38 | Excavation in trenches not exc 1.5m wide and not exc 1.5m deep and getting out in hard/dense soil. | | 40 | Cum |
|---|
| 39 | 39 | M&L for PCC (1:3:6) type C-1(20 mm graded aggregate) precast cement concrete block masonary with solid blocks exc 10 cm in width and setting in CM (1:4) etc complete. | | 3.8 | Cum |
|---|
| 40 | 40 | M&L for precast cement concrete 1:3:6 type C1 using 20 mm graded aggregate block solid building blocks or slabs in not exc 10cm thick (with plain or interlocking joints as directed ) complete set in CM 1:4 | | 345 | SQM |
|---|
| 41 | 41 | Taking down cement plaster on brick, concrete stone surfaces etc including raking out joints, hacking for key, scrubbing down with water etc. | | 230 | Sqm |
|---|
| 42 | 42 | M & L 10 mm thick rendering in cement mortar 1:6 on brick or concrete surfaces finished even & smooth without using extra cement | | 80 | Sqm |
|---|
| 43 | 43 | M & L for 5 mm thick plaster in cement mortar 1:4 on brick or concrete surfaces using WPC @ 3% by weight of cement over10 mm thick backing coat in cm 1:4 and finishing the surfaces even &smooth without using extra cement.(WPC will be measured and paid separately) | | 150 | Sqm |
|---|
| 44 | 44 | Supply only integral water proofing compound. | | 45 | Kg |
|---|
| 45 | 45 | M&L Preparing newly plastered wall surfaces and applying Two coats of cement base paint on wall surfaces over one coat of primer | | 150 | Sqm |
|---|
| 46 | 46 | M&L for three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified. | | 80 | Sqm |
|---|
| 47 | 47 | M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in path/pavings finished rough and laid in alternate bays to receive chequered tile all as specified and directed. | | 24 | Sqm |
|---|
| 48 | 48 | M&L for 15 mm thik screed bed or bedding layers of CM 1:6 incl roughning surfaces of old concrete floor by picking ,sweeping clean and washing down with water to remove dust etc. | | 26 | Sqm |
|---|
| 49 | 49 | M&L for chequrred cement concrete tile 20 cm x 20 cm x25 mm thick set jointed and pointed in neat cement slurry in floors, with grey cement and pigment. | | 26 | Sqm |
|---|
| 50 | 50 | Removal of soil of distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.5 meter above the starting point complete all as specified and directed. | | 30 | Cum |
|---|
| 51 | 51 | Material and labour for 75mm thick PCC 1:3:6 type C2 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even with out using with extra cement complete all as specified and directed. | | 800 | Sqm |
|---|
| 52 | 52 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for | | 120 | Cum |
|---|
| 53 | 53 | Extra for forming fair finishing drain or channels 80 cm inner girth in cement concrete using extra cement including forms, moulds stopped ends etc.complete all as specified and directed. | | 700 | RM |
|---|
| 54 | 54 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. | | 25 | Cum |
|---|
| 55 | 55 | Supply and fix TMT bars 10mm dia and over (confirming to Fe-410-S or Fe-410-0) cut to length, bent to shape as required including cranking & binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed. | | 1600 | Kg |
|---|
| 56 | 56 | Material and labour for providing pre-cast RCC (1:2:4) type 'B-1' using (20 mm graded crush stone aggregate) as in cover slabs of manholes and similar location including necessary form work and set in cement mortar (1:4) complete all as specified and directed. | | 25 | Cum |
|---|
| 57 | 57 | Demolition of pre-cast cement concrete block walling built in cement mortar complete all as specified and directed. | | 84.5 | Cum |
|---|
| 58 | 58 | Material and Labour for PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in bed complete all as specified and directed. | | 20 | Cum |
|---|
| 59 | 59 | Material and labour for providing precast cement concrete block masonry with PCC (1:3:6) type-C1 solid blocks, exceeding 10cm in width & set in cement mortar (1:6) complete all as specified and directed. | | 52 | Cum |
|---|
| 60 | 60 | Material and labour for rendering 15mm thick on concrete surface in cement mortar 1:4 , ffinished fair and even with out using extra cement complete all as specified and directed. | | 1640 | Sqm |
|---|
| 61 | 61 | Material and labour PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping/benching or similar etc complete incl necessary form work complete all as specified and directed. | | 11 | Cum |
|---|
