Civil Work For Repair And Renovation Of Officers Quarter For Making Barrack For The Crews At Taratala Depot .
Tender Value
21.69 Lakhs
Estimated cost
Bid Submission
30 Sep 2019
0 days left
EMD
43389
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Taratala Depot → West Bengal
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Civil Work For Repair And Renovation Of Officers Quarter For Making Barrack For The Crews At Taratala Depot .
BOQ
| Name of Work : Civil work for repair and renovation of officer’s quarter For making Barrack for the crews at Taratala Depot. | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Dismantling carefully terraced floor only\n(including floor finish if any) or lime terracing inground floor roof and removing rubbish asdirected within a lead of 75 m.\n(a) In Ground Floor including roof.\n\n | 1 | 66 | M3 |
| 2 | 2 | Labour for Chipping of concrete surface before taking upPlastering work.\n | 2 | 350 | M2 |
| 3 | 3 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in ground floor as perrelevant IS codes.\nPakur variety\n\n | 20 | M3 | |
| 4 | 4 | Supplying & laying 3mm thick pre-fabricated plastomericwater proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene(APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement@160 gms per sqm& both faces covered with thermo-fusiblepolyethylene film /MineraL on top face over a coat of primer@ 0.40 lit/sqm of manufacturer's specification on smooth,clean dry surface prepared wherever required.Lapjoint shall be provided of 75 mm in longitudinal & 100 mm intransverse direction and fused using LPG/ Propane torchemploying extra care ensuring full bondage, completeremoval of entrapped air and sealing edges into grooves inappropriate manner as per direction of Engineer -in-chargeall complete including materials,labour and applicabletaxes.\n | 350 | M2 | |
| 5 | 5 | Stripping off worn out plaster and raking outjoints of walls, celings etc. upto any height and inany floor including removing rubbish within alead of 75m as directed.\n | 300 | M2 | |
| 6 | 6 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortarincluding rounding off or chamfering corners as directed andraking out joints including throating, nosing and drip course,\nscaffolding/staging where necessary\n(ii) With 1:4 cement mortar\n(a) 20 mm thick plaster\n | 300 | M2 | |
| 7 | 7 | Supplying, fitting and fixing windows and ventilators with or withoutintegrated grills conforming to IS 1038-1975 and manufactured fromrolled steel sections conforming to IS 7452-1974 with non-frictionprojecting type, box type hinges, glazing clips, lugs locking bracket,\nhandle plate etc, including hoisting in position, straightening ifrequired, fixing lugs in cement concrete ( 1:2:4) with stone chips 20mm down cutting holes and mending good damages to match with\nexisting surface complete in all respect excluding glazing.\n(b) Openable steel windows as per IS sizes with side hung shuttersand horizotal glazing bars. \n | 30 | M2 | |
| 8 | 7.1 | (c ) Extra over item no. 33 (a) and (b) for, \n(ii) Top hung side hung ventilators as per I.S. sizes 580 mm. \n\n\n | 4 | M2 | |
| 9 | 7.2 | (iv) Two point nose steel handle including fitting and fixing. | 80 | EACH | |
| 10 | 7.3 | (vi) steel peg stay 300 mm long including fitting and fixing. \n | 80 | EACH | |
| 11 | 7.4 | (viii) M.S. integrated grill as per approved design integrated withsteel window or ventilator, joints continuously welded with M.S. flatsand bars. \n | 360 | KG | |
| 12 | 8 | Wood work in door and window frame fitted and fixed in position complete\nincluding a protective coat of painting at the contact surface of the frame\nexcluding cost of concrete, Iron Butt Hinges and M.S clamps.\n(e) Sal : Malayasian\n | 0.8 | M3 | |
| 13 | 9 | Supplying solid flush type doors of commercial quality, the timber frame\nconsisting of top and bottom rails and side styles of well seasoned timber 65mm\nwide each and the entire frame fitted with 37.5mm wide battens places both ways in order to make the door of solid core and internal lipping with Garjan orsimilar wood veneers using phenol formaldehyde as glue etc. complete, includingfitting, fixing shutters in position but excluding the cost of hinges and otherfittings in ground floor.\n(a) 35 mm thick shutters (single leaf)\n\n\n | 32 | M2 | |
| 14 | 10 | Supplying, fitting and fixing M.S. clamps for door and window frame made of flat\nbent bar, end bifurcated with necessary screws etc. by cement concrete(1:2:4) as\nper direction.\n(b) 40mm X 6mm, 200mm Length\n\n | 96 | Each | |
| 15 | 11 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI\nmark.\n(vii) 100mm. X 58mm. X 1.90mm.\n\n | 60 | Each | |
| 16 | 12 | i) Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with\n16mm dia rod with centre bolt and round fitting. \n(b) 250mm long\n\n | 16 | Each | |
| 17 | 13 | Iron socket bolt of approved quality fitted and fixed complete.\n(c) 150mm long x 10mm dia bolt.\n\n | 48 | Each | |
| 18 | 14 | Door stopper (Anodised aluminium)\n\n | 16 | Each | |
| 19 | 15 | Anodised aliminium D-type handle of approved quality manufactured from\nextruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed\ncomplete:\n(iii) 100 mm grip x 12 mm dia rod.\n | 32 | Each | |
| 20 | 16 | Supplying, fitting & fixing factory made foam PVC (density shall not be less than 600 kg/cum) door frame (finished weight of 2.73 kg/mtr.) of size 100mm X 45mm made off with 5mm thick extruded foam PVC sheet, mitre cut at junction of horizontal and vertical member and joined them by heat welding. Entire door frame profiles to be reinforced with steel primer coated 19 SWG 40mm X 20mmM.S. tube. An additional 5mm thick PVC sheet with desired colour/shade to be provided at the exposed surface and three nos 5mm thick PVC sheet to be provided as gap insert. The door frame to be fixed with wall by using 8mm dia. and 100mm long strainless steel screws and PVC fasteners. A minimum of 4 nos. screws to be provided for each vertical member & 2 nos. for horizontal member all complete as per direction of Engineer-in-Charge.\n(a) Plain Colour.\n\n | 20 | M | |
| 21 | 17 | Supplying, Fitting & Fixing 30 mm thick Factory made solid Panel PVC Door Shutter consisting of outer frame made out of M.S. tubes of 19 gauge thickness and size 19 mmx19 mm for styles, top and bottom rails, M.S. frame shall have cost\nof steel primers of approved make and manufacture, M.S. frame covered with 5 mmth. heat moulded PVC “C”channel of size 30 mm th, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on\neither sides forming styles; and 5 mm th. 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm tapered in 45 degree on the inner side to form top & bottom rail and 115 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel with 10 mm (5 mmx2) th.,20 mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 5 mm th. both side PVC sheet to be fitted in the M.S. frame welded/sealed to the styles &rails with 7 mm (5 mm+2 mm) th.x15 mm wide PVC sheet beading on inner side and joined together with solvent cement adhesive. An additional 5 mm th. PVC strip of 20 mm which is to be stuck on the interior side of the “C”channel using PVC solvent adhesive etc. complete excluding all necessary hardwares as per direction of Engineer-in-Charge.\nIn ground floor.\n | 8 | M2 | |
| 22 | 18 | (a) M.S.or W.I. Ornamental grill of approved design jointscontinuously welded with M.S, W.I. Flats and bars of windows,railing etc. fitted and fixed with necessary screws and lugs in ground floor.\n(i) Grill weighing above 10 Kg./sq.mtr and up to 16 Kg./sq. mtr.\n\n | 18 | Qntl. | |
| 23 | 19 | Supplying best Indian sheet glass panes set in putty and fitted and fixed\nwith nails and putty complete.\n(i) 3 mm thick\n\n | 30 | M2 | |
| 24 | 20 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive& grout materials etc.\n(A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thickcement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m& joint filling using white cement slurry 0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m\n(ii) Other than Coloured decorative including white.\n | 32 | M2 | |
| 25 | 20.1 | (B) Wall\nWith Sand Cement Mortar (1:3) 15 mm thick & 2 mm thickcement slurry at back side of tiles using cement @ 2.91\nKg/Sq.m& joint filling using white cement slurry @0.20kg/Sq.m.\n(a) Area of each tile upto 0.09 Sq.m\n(i) Coloured decorative\n | 90 | M2 | |
| 26 | 21 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in\nground floor.\n\n\n | 50 | M2 | |
| 27 | 22 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16\ngauge black annealed wire at every intersection, complete as per drawing and direction.\n(a) For works in foundation and upto roof of ground floor/upto 4 m\n(i) Tor steel/Mild Steel\n(ii)JSW/JSPC/SHYAM\n\n\n | 0.2 | MT | |
| 28 | 23 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.\n(i) Pakur Variety\n | 2 | M3 | |
| 29 | 24 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding 'P' or 'S' trap.\n(i) 580 mm X 440 mm\n | 4 | Each | |
| 30 | 25 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete.\n(ii) 470 mm X 280 mm X 340 mm\n | 2 | Each | |
| 31 | 26 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks,C.P. waste fittings of 32 mm dia., one pproved quality brass C.P. pillarcock of 15 mm dia., C.P. hain with rubber plug of 30 mm dia., approvedquality P.V.C. aste pipe with C.P. nut 32 mm dia., 900 mm long approvedquality P.V.C. connection pipe with heavy brass C.P. nut including ending good all damages and painting the brackets with two coats of approved paint.\n(ii) 550 mm X 400 mm size\n | 2 | Each | |
| 32 | 27 | Supplying, fitting and fixing bib cock or stop cock\n(a) (i) Chromium plated Bib Cock | 2 | Each | |
| 33 | 27.1 | (b) (i) Chromium plated Stop Cock | 2 | Each | |
| 34 | 27.2 | (d) (i) Chromium plated angular Stop Cock | 2 | Each | |
| 35 | 27.3 | (f) (i) Polythene Bib Cock / Stop Cock | 4 | Each | |
| 36 | 27.4 | (g) Supplying, fitting and fixing alloy iron with brass spindle bib cock / stop cock of approved brand and make, spray painted and tested to 21 kg\nper sq. cm.\n(i) 15 mm\n | 4 | Each | |
| 37 | 28 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories,specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew,reducing socket, reducing tee, short piece etc. fitted with holder batsclamps, including cutting pipes, making threads,fitting, fixing etc.\ncomplete in all respect including cost of all necessary fittings asrequired,jointing materials and two coats of painting with approved paintin any position above ground.\n(a) For Exposed Work \nPVC Pipes\n(Dia)\n15 mm\n\n | 20 | M | |
| 38 | 28.1 | (b) 20 mm | 20 | M | |
| 39 | 29 | Applying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes inwalls, floor etc. cutting trenches in any soil through masonry concretestructures etc if necessary and mending good damages including joining with jointing materials (Spun Yarn, Valamoid /Bitumen/M-Seal etc) complete.\nA) UPVC Pipes: \n(ii) 110 mm. Dia.\n | 20 | M | |
| 40 | 30 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992\n(A) (i) Single Socketed 3 Meter Length\n(b) 110 mm \n | 40 | M | |
| 41 | 30.1 | (B) Fittings \nix) Bend 45º \n(b) 110 mm \n | 8 | Each | |
| 42 | 30.2 | x) Bend 87.5º \n(b) 110 mm\n | 8 | Each | |
| 43 | 31 | Supplying, fitting and fixing G.I. pipes of TATA make with all ecessaryaccessories, specials viz. socket, bend, tee, union, cross, elbo, nipple,longscrew, reducing socket, reducing tee, short piece etc. fitted withholder bats clamps, including cutting pipes, making threads, fitting, fixing\netc. complete in all respect including cost of all necessary fittings asequired, jointing materials and two coats of painting with approved paintin any position above ground.\n(A) For Exposed Work \nc)(ii) 25 mm dia. medium quality\n | 50 | M | |
| 44 | 32 | Supplying, fitting and fixing stainless steel sink complete with wastefittings and two coats of painting of C.I. brackets.\n(a) Sink only \n(i) 530 mm X 430 mm x 180 mm\n | 2 | Each | |
| 45 | 33 | Scraping of moss, blisters etc. thoroughly from exterior surface of walls\nnecessitating the use of scraper, wire brush etc.\n | 450 | M2 | |
| 46 | 34 | Protective and Decorative Acrylic exterior emulsion paint of approvedquality, as per manufacturer's specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. Therate includes cost of material, labour, scaffolding and all incidentalcharges but excluding the cost of primer.\nIn Ground floor (Two Coat)\nb) Premium 100% Acrylic Emulsion\n | 450 | M2 | |
| 47 | 35 | Applying Exterior grade Acrylic primer of approved quality and brandon plastered or cencrete surface old or new surface to receivedecorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly,complete as per manufacturer's specification and as per direction of the EIC.\nIn Ground Floor:\n(a) One Coat\n | 450 | M2 | |
| 48 | 36 | Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering orcement mortar (1:2) (as necessary), to make the surface suitable forreceiving distemper.\n | 950 | M2 | |
| 49 | 37 | Applying Interior grade Acrylic Primer of approved quality and brandon plastered or cencrete surface old or new surface to receiveDistemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification andas per direction of the EIC. (In Ground Floor)\n(a) One Coat\nii) Solvent based interior grade Acrylic Primer.\n | 950 | M2 | |
| 50 | 38 | Acrylic Distemper to interior wall, ceiling with a coat of solvent basedinterior grade acrylic primer (as per manufacturer's specification)including cleaning and smoothning of surface.\nTwo Coats\n | 950 | M2 | |
| 51 | 39 | a) Priming one coat on steel or other metal surface with synthetic oilbound primer of approved quality including smoothening surfaces by sandpapering etc. | 90 | M2 | |
| 52 | 39.1 | (b) Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc\n | 80 | M2 | |
| 53 | 40 | (A) Painting with best quality synthetic enamel paint of approved makeand brand including smoothening surface by sand papering etc. includingusing of approved putty etc. on the surface, if necessary :\n(a) On timber or plastered surface :\nWith super gloss (hi-gloss) -\n(ii) Two coats \n | 80 | M2 | |
| 54 | 40.1 | (b) On steel or other metal surface :\nWith super gloss (hi-gloss) - \n(iv) Two coats\n | 90 | M2 | |
| 55 | 41 | Dismantling all types of masonry excepting cementconcrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directedwithin a lead of 75 m.\na) In ground floor including roof.\n | 50 | M3 | |
| 56 | 42 | Dismantling R.C. floor, roof, beams etc. includingcutting rods and removing rubbish as directedwithin a lead of 75 m. including stacking of steelbars.\n(a) In ground floor including roof.\n | 40 | M3 | |
| 57 | 43 | Single Brick Flat Soling of picked jhama bricks including ramming anddressing bed to proper level and filling joints with local sand. | 400 | M2 | |
| 58 | 44 | (I) Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor\n(A) [Pakur Variety]\n(a) 1:3:6 proportion\n | 40 | M3 | |
| 59 | 45 | Brick work with 1st class bricks in cement mortar (1:6) \n(b) In superstructure, ground floor\n | 5 | M3 | |
| 60 | 46 | M.S. structural works in columns, beams etc. with simple rolledstructural members (e.g. joists, angle, channel sections conformingto IS: 226, IS: 808 & SP (6)- 1964 connected to one another withbracket, gussets, cleats as per design, direction of Engineer-inchargecomplete including cutting to requisite shape and length,fabrication with necessary bolting, metal arc welding conforming to\nIS: 816- 1969 & IS: 1995 using electrodes of approved make andbrand conforming to IS:814- 2004, haulage, hoisting and erectionall complete. The rate includes the cost of rolled steel section,consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidentalchages such as electricity charges, labour insurance charges etc.\nI) For structural members of specified sections weighing less than\n22.5 Kg./m \n\n\n | 1.2 | MT | |
| 61 | 47 | Supplying 1.5mm thick M.S. sheet fitted and fixed on one or bothfaces of M.S./ W.I. gate etc. with point welding at not more than150mm apart complete in all respect as per design including cost of all labour and materials.\n | 20 | M2 | |
| 62 | 48 | Surface Dressing of the ground in any kind of soilincluding removing vegetation inequalities notexceeding 15 cm depth and disposal of the rubbishwithin a lead upto 75 m as directed. | 6000 | M2 | |
| 63 | 49 | ADD : GST - 12% (SGST = 6% & CGST = 6%) | 1 | no. | |
| 64 | 50 | ADD : WEST BENGAL LABOUR WELFARE CESS = 1% | 28 | 1 | no. |
| 65 | Total in Figures |
AI Tender Summary
Tender Timeline
Sep 09, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedSep 30, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 17, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender