Dry Docking / Repairs Of Pilot Launch Ml Biju Pattanaik , Survey Launch Ml Laxmi , Pollution Control Vessel Ml Kali , Mooring Launches Ml Chandi And Ml Charchika And Repairs Of Slipway Cradle Of Paradip Port Trust, Paradip-Odisha

TDR : 21452800

Tender Notice
BOQ

Expired

Paradip , Odisha

Tender Brief : Dry Docking / Repairs Of Pilot Launch Ml Biju Pattanaik , Survey Launch Ml Laxmi , Pollution Control Vessel Ml Kali , Mooring Launches Ml Chandi And Ml Charchika And Repairs Of Slipway Cradle Of Paradip Port Trust

Document Fees
₹ 10000 /-

EMD
₹ 203350.0 /-

Tender Value
₹ 1.01 Crore /-

Submission Date
12-09-2019

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !

NATURE OF WORK : Dry Docking / Repairs of Pilot Launch ML Biju Pattanaik, Survey Launch ML Laxmi, Pollution Control Vessel ML Kali, Mooring Launches ML Chandi & ML Charchika and Repairs of Slipway Cradle of Paradip Port Trust
1	1	ML Biju Pattnaik (Deck Side Defects)
2	1.01	To quote for docking , undocking & placing of the launch on the blocks on the cradle of the slipway	1	L/S
3	1.02	The entire under water portion and Hull portion above water line upto Main Deck and main deck area including Rudder, Bilge Keel ,and all the structures are to be thoroughly cleaned, scrapped to remove marine growth,rust etc and grit blasted to SA 2.5 grade surface finish. To quote including cost of materials.	380	Sq.Mtrs.
4	1.03	To quote for Painting of under water portion of the hull with 6coats of Epoxy Paint by airless spray (2Coats primmer+2coats sealer+2 coats Anti fouling/Finish). Paint PPT Supply.	380	Sq.Mtrs.
5	1.04	To quote for Scrapping, power cleaning of engine room bilges and floor plate, steering compartment, Chain Locker, Fore peak and void spaces including frames, angles, bulkheads and foundation of main engines, Generators and all other equipment including ceiling and side wallsl . To paint above area with 4coats of Epoxy Paint by airless spray (1Coat primmer+ 2coats sealer+1 coat Finish). Paint PPT Supply.	650	Sq.Mtrs.
6	1.05	The Anchors along with the chain to be lowered, cleaned, Grit blasted and painted with 2 coats of epoxy primer & 2 coats of finish paints. Joining shackles & ‘D Shackles to be opened, freed, marked and painted. Anchor chain to be changed as per PPT/IRS requirement. Bitter end connecting to be checked and if necessary strengthened. To quote including cost of materials, Paint PPT Supply	1	No
7	1.06	Packing for all the weather deck doors and hatch cover for E/R room and other spaces are to be changed including renewal of channels to make it water tight. Packing material shall be neoprene/epdm ,hollow type Width= 20 mm , 25 mm & 40 mm. To quote including cost of materials.	50	Mtrs.
8	1.07	To gauge the Hull of Pilot Launch Biju Pattnaik by IRS Certified firm.	300	Point
9	1.08	To quote for overhauling of the chain locker hand pump ( including spares and other materials)	1	No
10	1.09	To overhaull the emergency fire hand pump( Quote L.S. including spares and other materials)	1	No
11	1.1	Port & Starboard Wheel House FRP Doors (size 188 X 68 cm) and handle to be repaired with renewal of S.S. Hinges, the door to be made water tight with renewal of rubber packing hollow type (40 mm). Inner face of the door to be fitted with Marine grade 19mm ply & sunmica ( kitply,greenply make) To quote L.S including cost of materials.	2	L/S
12	1.11	New Kent(RO) to be fitted in wheel house wit nessary piping and fittings. Quote L. S. including installation.	1	No
13	1.12	All window sceen with heavy duty rod ,rod stands are to be changed with new screens, ( 01mx 1.5mtr ) size Screen material and design to be approved by EIC. To quote including cost of Materials	10	No
14	1.13	To quote for renewal of master seat in wheel house(including seat cover).	1	No
15	1.14	To quote for supply and installation of radar with a range of 200feet to 25nM, 12 inch LCD / led display with inbuilt charts,GPS ,compass ,AIS input ,9V to 31 volt power supply,Radar rpm 21-35 rpm, Transmitter type ,No magnetron,all solid state instant on type. To quote including Cost of Materials.	1	No
16	1.15	To quote for Motorola VHF base radio set with antenna and cable(Model- MOTOTRBO-XiR-M3688, output power 25W,operable between frequency 136-174 Mhz, along with standard assoceries- hand set unit, DC power cable, Antenna, Patch code, coaxial antenna cable of 15 meters with connector fitted at both ends and 16 nos specified channel to be tuned. Complete installation and comissioning. To quote including cost of materials.	1	No
17	1.16	To quote for Installation of EM-Trak AIS-Class-B, Combined GPS and VHF antenna, GPS and VHF antenna Cable (15 meter length), connectors etc., Power supply unit for AIS. Complete installation and commissioning of the AIS. To quote including cost of materials.	1	No
18	1.17	To quote for necessary replacement/renewal of ply in Pilot cabin/wheel house with water proof and fire retardant ply. (10mm) of Green Ply / Kit ply with sunmica. To quote including cost of materials.	50	Sq.Meter
19	1.18	To quote for repair of toilet & pantry (Cup boards, basin, mirror, LED lights renewal). All ply to be used of fire retardant& marine grade type. To quote including cost of materials.	10	Sq,Meter
20	1.19	The side glasses of the cabin to be removed & fitted back with new glass frames, proper rubber frames, rubber gaskets & automotive sealant. No leakage in Side glasses during waterspray test .( Quote Including cost of materials)	6	Nos
21	1.2	F.W tank base to be removed & same to be replaced fitted in same place (Renotuf Double Layer - 500 ltrs). To Quote Including cost of materials).	1	No
22	1.21	To quote for renewal of the pilot seat push back system,(including cost of materials and seat covers)	10	Nos
23	1.22	The Damaged wood from the Main Deck are to be removed then area to be grit blasted to SA 2.5 grade and painted with 02 coats of Primer and 02 coats of Finish paint. New seasoned teak wood, new St. Steel Nut and bolts ,washers, wooden plogs are to be used to fix the wood. The joints are to be sealed with new Packing, and marine glue to make it water tight. To quote Including cost of materials.( paint PPT supply ). the cross section of sal wood is 20 mm thick X 150 mm width. Quote Including cost of materials.	25	Sq.Mtrs.
24	1.23	To remove from mast base from monkey island & same base to be fitted in same place with Required St. Steel nut &bolts and to be covered with 5mm thick FRP cover ti make it watertight. Area to be fifred is 01 Sq.meter. Quote Including cost of materials).	1	No
25	1.24	To supply,install and comissioning new GPS, (Model- FURUNO GPS, Navigator (GP-33) along with 15 meter cable,antenna with connector fittings. Quote Including cost of materials)	1	No
26	1.25	To quote for Steel Renewal\nSteel Platings along with frames, beams, brackets and all the required fittings shall be renewed at following locations as per the normal practice of ship construction / IRS Construction Rules:\n(a) Hull Platings (Under Water & Above Water)\n(b) Main Deck Platings\n(c) Under Deck Bulk Heads\n(d) Sea Chest Platings\n(e) Skeg, Bilge Keel and Rudder\n(f) Fender Holding Plates\n(g) Any other steel structure as required by PPT\n(h) Engine room floor plates securing angles , stair case ,man hole covers.\nFirm to Quote above steel renewal including cost of Steel Plates per Ton Basis. M.S. Plates of 8 MM / 6 MM / 4 MM Thickness will be used for renewal of platings. The M.S. Plates are to be of approved type for Ship Construction ( No.IS 2062). IACS approved welding rod to be used. Before starting any plate renewal , certificate from manufacture to be submitted.\n	8	Tons
27	1.26	To remove the ‘D’ type Rubber Fenders from in and around the Ship side, crop the top & bottom holding plates including the stiffeners. To weld new plates of 8 mm thick X 100 mm width including the triangular stiffeners at a gap of 1 Mtr. and fit back new / old fenders in place with new nuts & bolts (20 mm dia X 200 mm). To quote the cost of removal & fixing of fenders including Nuts & Bolts excluding cost of Rubber Fenders & Steel Renewal.	50	Mtrs
28	1.27	Rubber Bidding for 4 Nos. Engine Room Vent head Fire Door (Size 20mm X 15 mm X 1m) to be renewed. 7 Nos. Bolts with Hinges and Butterfly nuts to be fitted to make the door air tight. Quote L. S.	4	Nos
29	1.28	Fiber coating on weather deck on monkey island to be repaired/renewed and make water tight. To quote per sq.mtr. for 3mm top coating including cost of materials.	40	Sq.Mtrs.
30	1.29	The rubber bidding ( 20mm size ,length 400 mm) , St.Steel wire mesh 1 mm thick wire & securing chain 1 inch,300 mm length of Air vent Cover to be renewed. To quote including the materials.	7	Nos
31	1.3	Pilot Cabin & wheel house floor mat to be renewed with new linoleum sheet (3mm) . Flooring to be made with Marine ply (Kit ply – 12 mm thick ness). Area – 20 Sq.mtr. To quote per sq.mtr. Quote Including cost of materials.	40	Sq.Mtrs.
32	1.31	New teapoy to be fixed in pilot cabin (Teak colour, floor securing arrangement with bottle screw). Quote L. S. including cost of materials	1	No
33	1.32	Fire hose box to be renewed with new box with locking arrangements. (Make of FRP) and supply of new fire hose (MMD approved). Quote Including cost of materials)	2	Nos
34	1.33	Supply of EPDM material D-Type fenders of 150mm x 150 mm x 2 meter. Test certificates (as per ISI standard) from the manufacturer to be furnished. Quote L. S.	55	Meter
35	1.34	Engine side Defects
36	1.35	To remove, clean & Paint the sea chest along with gratings . Sea chest area to be grit blasted & Painted with 6 coats of epoxy paint. .To quote including cost of materials. Paint PPT Supply.	2	Nos
37	1.36	To remove, dismantle, and Overhaul the following Overboard, Sea chest & intermediate valves of sea water pipeline:-After overhauling all the valves shall be pressure tested at 5 Kg/ sq.cm and fit back with new gasket, St. Steel nuts, bolts' joints., supporting clamps. \nTo quote Including cost of materials \n\n \n\n\n\n\n
38	1.37	1) Gate Valve – 125NB	2	Nos
39	1.38	2) SDNR Valve - 125NB	1	No
40	1.39	3) Gate valve - 65NB	2	No
41	1.4	4) SDNR Valve – 65NB	6	Nos
42	1.41	5) Globe Valve- 80NB	2	Nos
43	1.42	6) SDNR Valve – 65NB	8	Nos
44	1.43	7) Globe Valve – 50	6	Nos
45	1.44	8) Globe Valve – 25	2	Nos
46	1.45	Following pipe lines in engine room, deck, are to be reomoved, renewed with schedule 40 seamless pipes with old Flanges. All the pipe line are to be welded along with flanges from both sides. The pipelines are to be painted inside&outside and fitted back with new joints, Stainless steel nuts & bolts and supporting U- clamp whereever required. To quote Including cost of materials.
47	1.46	1)15mm bore	40	meters
48	1.47	2) 25mm bore	40	meters
49	1.48	3) 40mm bore	30	meters
50	1.49	4) 50MM bore	60	meters
51	1.5	5) 65MM bore	50	meters
52	1.51	6) 75 MM bore	12	meters
53	1.52	7) 100 mm bore	12	meters
54	1.53	Spindle of Isolated Valves for the emergency Fire Pump to be overhauled with renewal of wheels. Quote L. S.	1	No
55	1.54	Quote for supply & installation of a complete set of split Air conditioning unit including copper pipes and laggings.Make:HITACHI,Daikin/CARRIER). cap 1.5 Ton,Single phase.230V, invertor type. To quote Including cost of materials	2	Nos
56	1.55	To supply and fit the Navigational lights as per sample (Twin fittings ( AC and DC) with classification society approved certificate a) mast light (White) - 225 degree visibility, b) stabboard light (Green) - 112.5 degree visibility , c) port light (Red) -112.5 degree visibility , d) stern light (White) - 225 degree visibility, e) pilot on board (Red) - 360 degree visibility, f) pilot on board (white) -360 degree visibility. All lights are to be of LED light type.To qoute including cost of materials.	6	No
57	1.56	30 Watt Led ceiling lights in Pilot cabin and wheel house to be renewed (Philips/Havells). With necessary change in ceiling, Quote Including cost of materials.	6	No
58	1.57	To quote for supply of 24 inches wiper blades	12	Nos
59	1.58	To quote for supply and fitting of (100wt) led flood light in water tight casing ,IP 66 grade ( make - havells, bajaj , CG, philips,)	2	Nos
60	1.59	Following engine exhaust lines are to be insulated with HR lagging and GI sheet
61	1.6	i) Port ,STBD and Center mainengine exhaust pipe ( 06 inch size)to be insulated with HR lagging and GI sheet cover, including renewal of SS bellow . ( approximate length of pipe 02 meters ) Quote Including cost of materials.	6	nos
62	1.61	ii) Exhaust pipe(10 Inch dia) inside steering compartment to be insulated with HR lagging and GI sheet cover.(appx.length 5.5meters). To quote including cost of materials..	2	Nos
63	1.62	iii) Exhaust pipe(02 Inch dia) of DG exhaust to be insulated with HR lagging and GI sheet cover.(appx.length 2meters) in cluding renewal SS exhaust bellow . To quote including cost of materials.	2	Nos
64	1.63	Man hole covers for the Diesel tanks (E/R) to be opened, tanks to be cleaned properly. After inspection and survey all the man hole covers are to be fitted back with new gaskets of 4mm thick.Covers are to be watertight. Deisel tank size as follows:
65	1.64	i) 100mm X 1400mmX 900 mm	2	Nos
66	1.65	ii) 950mm X 950mm X 900mm	1	No
67	1.66	Diesel tank Gauge glass cocks are to be removed, Overhauled & fifed back with Proper sealant, new ‘O’ rings &gaskets/glands ,new glass if required. To quote including cost of materials.	5	Nos
68	1.67	Engine room blower trunking to be renewed,approximate size 30cmx40cm section,with 02mm GI sheet. To quote including cost of materials.	8	meter
69	1.68	Sea water line strainers are to be removed and fitted back with new stain less steel strainers of 316 grade, 3mm thick and of 300mm length & 220 mm dia ( approx.size) .To quote including cost of materials.	2	Nos
70	1.69	Old bilge line strainers are to be removed and fitted back with new stain less steel strainers 316 grade 200mm ( approx.size) length & 150 mm dia.To quote including cost of materials.	2	Nos
71	1.7	Centre engine Silencer Pipeline are to be provided with new lagging of HR Materials and GI Sheet Cover approximate length 03 meters. To quote including cost of materials.	1	No
72	1.71	Complete renewal of anchor chain howser pipe (size 10”) Sch 80 pipe ( appx length 02 meters). To quote including cost of materials.	1	No
73	1.72	To quote for supply of following items
74	1.73	i) oil cooler (Stbd Dg) as per sample	1	No
75	1.74	ii) transparent poly acrylic UV resistant sheet of size 1M x1M,06 mm thick	1	No
76	1.75	Engine room entrance shedding to be extended to the Pilot cabin and Pilot cabin roof to be extended at stern by 6 inches and of length 03 meters. To quote including cost of materials.	1	No
77	1.76	Engine room blower air intake manifold to be removed , fabricated new ,gritblasted and painted with 06 coats of Epoxy paint, (paint PPT supply). Fitted back with new SS hinges, sealing rubber packing,St.Steel. Wing nut and bolts.To quote including cost of materials.	2	Nos
78	1.77	To quote for dismantle ,clean,revarnish and overhaul the following electrical Motors with required consumables and bearings. Cooling fan covers to renew.
79	1.78	i) Blower Motor (2.3Kw), 440volt, 3ph.	2	Nos
80	1.79	ii) Anchor motor (7.5kw), 440volt, 3ph.	1	No
81	1.8	Alternator overhauling,revarnishing with bearing to be replaced 12.5kva,440v,60hz ( ), Insulation to be improved to 50Mohm. Quote L. S.	2	Nos
82	1.81	To quote for supply of following items
83	1.82	i) Self starter for Main.Engine Make-Delco Remy,series:42MT,type:400,volt-24V D/C	1	No
84	1.83	ii) Alternator 24V 55amps (TVS)SA28-55A-24V	2	Nos
85	1.84	iii) Alternator 12V 35amps( TVs)	1	Nos
86	1.85	iv) Rpm indicator digital meter 118 teeth, 24V, WITH SPEED Pickup unit ( make twintech)	2	Nos
87	1.86	To quote for supply and commissioning of electric horn/Siren with audibility range for 3 KNOT, 230V AC	1	No
88	1.87	To quote for supply and fitting of water tight deck light fittings with (9wt led bulb) ( Make Havells, Bajaj, Philips, CG )	6	Nos
89	1.88	To quote for supply and installation of 30 watt led flood light fitting IP66 in Engine room and steering room with necessary modification ( Make Havells, Bajaj, Philips, CG )	8	No
90	1.89	To quote for supply and replacement of 2.5 sq mm two core cable (Havells/Finolex) for all navigational light,deck light, flood light and search light.with proper sealing on wheel house.Approximate cable use 200meters	1	LS
91	1.9	To quote for supply and installation of following items
92	1.91	i) Heavy duty battery charger 72v, 10amps.Elak make	1	Nos
93	1.92	ii) 11 pin relay (Model MK3P-NS) Make Omron (As per sample)	10	Nos
94	1.93	To quote for supply and installation of Wall mounting 12 inches fan in wheel house and Pilot cabin. Make: Havells / bajaj,/ Cinni/ Usha	7	Nos
95	1.94	Insulation test by meggar of all dc line of Battery charger cum dc light supply and replace defective cables if found. Megering up to 01 Mohm. To quote including cost of materials.	1	LS
96	1.95	ML LAXMI (Deck Side Defects)
97	1.96	To quote for docking and undocking & placing of the launch on the blocks on the cradle of the slipway	1	L/S
98	1.97	The entire under water portion and Hull portion above water line upto Main Deck and main deck area including Rudder, Bilge Keel ,anchor chain,anchor, sea chest and all the structures are to be thoroughly cleaned, scrapped to remove marine growth,rust etc and grit blasted to SA 2.5 grade surface finish.	350	Sq.m
99	1.98	To quote for Painting of underwater portion of the hull with 6coats of Epoxy Paint by airless spray (2Coats primmer+2coats sealer+2 coats Anti fouling/Finish. Paint PPT Supply.	350	Sq.m
100	1.99	To quote for Scrapping, power cleaning of engine room bilges and floor plate, steering compartment , Fore peak, Chain Locker and void spaces including frames, angles, bulkheads and foundation of main engines, Generators and all other equipment including roof and side walls of all compartments. To paint above area with 4coats of Epoxy Paint by airless spray/brush (1Coats primmer+ 2coats sealer+1 coats Finish). Paint PPT Supply.	500	Sq.m
101	2	wheel house both side door to be repaired,fibering with renew of rubber bidding. (To quote including cost of materials)	2	Nos
102	2.01	survey cabin door to be repaired in the wheel house. Quote including cost of materials	1	No
103	2.02	Anchors along with the chain to be lowered, cleaned, Grit blasted and painted with 2+2 coats of epoxy paints.Anchor chain to be replace as per PPT requirement. Quote including cost of materials, Paint PPT Supply.	1	L/S
104	2.03	To quote for supply and installation of radar with a range of 200 feet to 25 nM, 12 inch LCD display with inbuilt chart,GPS ,compass ,AIS input ,9V to 31 volt power supply,Radar rpm 21-35 rpm, Transmitter type , No magnetron,all solid state instant on type. Quote including Cost of Materials	1	No
105	2.04	To quote for supply of EPDM material D type fender of size 150mm X 02 meter, Quality Test certificate ( as per ISI standard ) from manufacturer to be provided	30	meters
106	2.05	To supply and install of New windlass control boxwith renewal of nessary wiring. To quote including cost of materials.	1	No
107	2.06	Packing for all the weather deck doors and hatch cover for E/R room and other spaces are to be changed. To quote per Meter including cost of materials. (Rubber: Width=40mm, hollow tpye, material EPDM/Neoprene)	50	Mtrs
108	2.07	To qoute for Steel Renewal\nSteel Platings along with frames, beams, brackets and all the required fittings shall be renewed at following locations as per the normal practice of ship construction / IRS Construction Rules:\n(a) Hull Platings (Under Water & Above Water)\n(b) Main Deck Platings\n(c) Under Deck Bulk Heads\n(d) Sea Chest Platings\n(e) Skeg, Bilge Keel and Rudder\n(f) Fender Holding Plates\n(g) Any other steel structure as required by PPT\n(h) Engine room floor plates securing angles , stair case ,man hole covers.\nFirm to Quote above steel renewal including cost of Steel Plates per Ton Basis. M.S. Plates of 8 MM / 6 MM / 4 MM Thickness will be used for renewal of platings. The M.S. Plates are to be of approved type for Ship Construction ( No.IS 2062). IACS approved welding rod to be used. Before starting any plate renewal , certificate from manufacture to be submitted.\n	7	Tons
109	2.08	To remove the old “D” type rubber fenders from in and around of main deck, crop the top and bottom holding plates including the stiffeners. Fix new Fenders with new Nuts & Bolts. To quote per Meter renewal excluding cost of rubber fenders and steel renewal.	50	Mtrs
110	2.09	Wheel House/Survey Cabin floor mat to be removed. Flooring to be covered with new Linonium. To quote including cost of materials	30	Sq.Meter
111	2.1	To remove and replace toilet pipeline with new upvc pipe lines of toilet room with required gasket and nut bolts,paste etc. To quote including cost of materials.	1	LS
112	2.11	Engine side Defects
113	2.12	Sea chest / bilge & G.S. lines filters to be removed cleaned & to be boxed back with new nuts, bolts & gasket. To quote Including cost of materials	5	Nos
114	2.13	To remove, dismantle, and Overhaul the following Overboard, Sea chest & intermediate valves of sea water pipeline:-After overhauling all the valves shall be pressure tested at 5 Kg/ sq.cm and fit back with new gasket, St. Steel nuts, bolts' joints., supporting clamps. \nTo quote Including cost of materials \n\n \n\n\n\n\n
115	2.14	a) Glove Valve – 100 NB	8	Nos
116	2.15	b) SDNR Valve – 50 NB	5	Nos
117	2.16	c) SL Valve – 50 NB	10	Nos
118	2.17	d) Foot Valve – 50 NB	2	Nos
119	2.18	f) SD. RT Angle Valve – 50 NB	4	Nos
120	2.19	g) Air Vent Valve – 50 NB	4	Nos
121	2.2	h) fire hydrant Valve – 65 NB	2	Nos
122	2.21	i) Quick Closing Valves – 40 NB	2	Nos
123	2.22	j) Globe Valve –25 NB	4	Nos
124	2.23	Following pipe lines in engine room, deck, are to be reomved, renewed with schedule 40 seamless pipeswith old Flanges. All the pipe line are to be welded along with flanges from both sides. The pipelines are to be painted and fitted back with new joints, Stainless steel nuts & bolts and supporting U- clamp whereever required. To quote Including cost of materials.
125	2.24	1)15mm bore	20	meters
126	2.25	2) 25mm bore	15	meters
127	2.26	3) 40mm bore	20	meters
128	2.27	4) 50MM bore	30	meters
129	2.28	5) 65MM bore	15	meters
130	2.29	6) 75 MM bore	12	meters
131	2.3	7) 100 mm bore	5	meters
132	2.31	Fuel oil tanks ( inside) to be cleaned properly & the manhole door to be fitted with new gaskets( Champion -4mm) . To quote Including cost of materials.
133	2.32	(a) Storage tank – 2200 ltr.	1	No
134	2.33	(b) Service tank – 500 ltr.	1	No
135	2.34	To quote for Repairing of blower trunking by GI sheet and fibering the whole sheet	10	meters
136	2.35	To quote for ovehaualing of the 02 Nos fuel pumps and 12 nos injectors of NTA 743 main engine at authorised service center ,including spares from authorised dealer.	1	No
137	2.36	To quote for supply of following items for cummins main engine NTA743 model
138	2.37	a) main engine air filter casing	1	Nos
139	2.38	b) All flexible hoses of main engine set	2	Nos
140	2.39	c) Fresh water pumps for main engine.	1	Nos
141	2.4	d) Exhaust manifold for main engine	1	Nos
142	2.41	e) Idle pulley for seawater pump.	2	Nos
143	2.42	Sea water line strainers are to be removed and fitted back with new fabricated stain less steel strainers 316 grade of 3mm thick and of 300mm length & 200 mm dia .To quote including cost of materials.	2	Nos
144	2.43	To remove the cocks of diesel tank, overall and fit back with required O-ring & gaskets. Make those leakproof. To quote Including cost of materials.	2	Nos
145	2.44	Transformer to be cleaned & Varnished Properly and insulation to be improved up to 50 M.ohms. Detail of Transformer 415 V to 230V AC, 12KVA (4 X 3 KVA). To quote Including cost of materials	1	No
146	2.45	Quote for Rewinding of one transformer of capacity 04KVA, 415 Volts to 230 Volts. To quote Including cost of materials	1	No
147	2.46	To quote for dismantling ,revarnishing & overhauling of Alternators of 30KVA 415 V, 42 Amp, 1500RPM with renewal of bearings and other spares. To quote Including cost of materials	2	Nos
148	2.47	To quote for supply and fitting of (100wt) led flood light in water tight casing ,IP 66 grade ( make - havells, bajaj , CG, philips,). To quote Including cost of materials	1	No
149	2.48	To quote for supply and installation of 30 watt led light flood fitting IP66 in Engine room and steering room with necessary modification ( Make Havells, Bajaj, Philips, CG ). To quote Including cost of materials	8	Nos
150	2.49	To quote for supply & fitting of highspeed fan 12\" (crompton/havells) in the wheel house,survey room. To quote Including cost of materials	4	Nos
151	2.5	To quote for supply and installation of new wiper motor with arm and blade(TVS Lucas make or equivalent) ( spare wiper blade 03 nos).To quote Including cost of materials	1	No
152	2.51	KALI (Deck Side Defects)
153	2.52	To quote for docking and undocking & placing of the launch on the blocks on the cradle of the slipway	1	L/S
154	2.53	The entire under water portion and Hull portion above water line upto Main Deck and main deck area including Rudder, Bilge Keel ,anchor chain,anchor, sea chest and all the structures are to be thoroughly cleaned, scrapped to remove marine growth,rust etc and grit blasted to SA 2.5 grade surface finish.	350	Sq.Meter
155	2.54	To quote for Painting of above area of the hull with 6coats of Epoxy Paint by airless spray including Rudders & Skeg.(2Coats primmer+2coats sealer+2 coats Anti fouling/Finish. Paints PPT Supply.	350	Sq.Meter
156	2.55	To quote for Scrapping, power cleaning of engine room bilges and floor plate, steering compartment , Fore peak and void spaces including frames, angles and foundation of main engines, Generators and all other equipment. To paint ceiling & side walls of above with 4coats of Epoxy Paint by air (2 Coats primmer+ 01 coat sealer+1 coats Finish) with spray/brush. Paints PPT Supply.	500	Sq.Meter
157	2.56	Anchors along with the chain to be lowered, cleaned, Grit blasted and painted with (2+2) coats of epoxy paints. Anchor chain to be change as per PPT requirement. Paint PPT supply.To quote Including cost of materials.	1	Lumpsum
158	2.57	Windlass gear box including brakes to be dismantled completely, cleaned and overhauled with necessary spares ( bearing ,seals etc )and boxed back with new packing, new oil seal,brake linings,SS nuts and bolts.Panel board to be overhaouled with required spares. Satisfactory trial to be shown after fitting in place. To quote Including cost of materials.	1	No
159	2.58	Floor mats to be renewed. (Self adhesive & removable, PVC material, wood grain type). Quote including cost of materials.	20	Sq.Meter
160	2.59	St.Bd window of wheel house 2ftX 3 ft toughen glass to be replaced. New frame, rubber gaskets and automotive sealant to be used for fitting.To quote Including cost of materials.	1	No
161	2.6	To quote for removal of the ‘D’ type Rubber Fenders from in and around the Ship side, crop the top & bottom holding plates including the stiffeners. To weld new plates of 8 mm thick X 100 mm width including the triangular stiffeners at a gap of 1 Mtr. and fit back new / old fenders in place with new nuts & bolts (20 mm dia X 200 mm). To quote the cost of removal & fixing of fenders including Nuts & Bolts excluding cost of Rubber Fenders & Steel Renewal.	55	Mtrs
162	2.61	Garbage Tray Foundation Bracket with garbage collection basket support corroded. Necessary modification are to be carried out so that garbage basket can dip inside water and collected materials can be shifted to collection bin.new hydraulic cylinder and control valve with renewal of wiring and filters. To quote Including cost of materials.	1	No
163	2.62	Packing for all the weather deck doors and hatch cover for E/R room and other spaces are to be changed. Width=40mm ,Epdm materials, hollow type .Approx.length 40 meters To quote lumpsum including cost of materials.	1	LS
164	2.63	To qoute for Steel Renewal\nSteel Platings along with frames, beams, brackets and all the required fittings shall be renewed at following locations as per the normal practice of ship construction / IRS Construction Rules:\n(a) Hull Platings (Under Water & Above Water)\n(b) Main Deck Platings\n(c) Under Deck Bulk Heads\n(d) Sea Chest Platings\n(e) Skeg, Bilge Keel and Rudder\n(f) Fender Holding Plates\n(g) Any other steel structure as required by PPT\n(h) Engine room floor plates securing angles , stair case ,man hole covers.\nFirm to Quote above steel renewal including cost of Steel Plates per Ton Basis. M.S. Plates of 8 MM / 6 MM / 4 MM Thickness will be used for renewal of platings. The M.S. Plates are to be of approved type for Ship Construction ( No.IS 2062). IACS approved welding rod to be used. Before starting any plate renewal , certificate from manufacture to be submitted.\n	7	Tons
165	2.64	Navigation lights base are to be removed and new base fitted back in same place. To quote Including cost of materials.	5	No
166	2.65	To Quote for supply and installation of New fresh water tank Sintex Sintex CCWS 0050-02-TLW 500 L Triple Layered ( 500 liters Capacity ) Heavy duty type and its stand above wheel house.To quote Including cost of materials	1	No
167	2.66	Derrick at forward deck is to be repaired and derrick heights to be shortened and new wire for lifting to be fitted. To quote Including cost of materials.	1	No
168	2.67	Mast to be removed from mast base & same base to be fitted in same place with SS bolts and 5mm thick FRP to be applied over it. To quote Including cost of materials	1	No
169	2.68	To quote for removal and replacement of new tiles, Commodo of the toilet with required gasket and nut bolts.To quote Including cost of materials	1	L/S
170	2.69	Wash basin in the wheel house with basin, pipe and the same to be renewed with new jaquor tap. To quote Including cost of materials	1	L/S
171	2.7	To remove and replace new UPVC pipe lines of toilet room with required materials. To quote Including cost of materials	1	LS
172	2.71	Wheel house door to be repaired with 01 inch marine grade ply and other material (To quote including cost of materials).	2	No
173	2.72	To quote for Wheel House roof top fibring (FRP).To quote Including cost of materials	4	Sq.Meter
174	2.73	To quote for necessary replacement/renewal of ply in wheel house with water proof and fire retardant ply. (10mm) of Green Ply / Kit ply with sunmica.To quote Including cost of materials	22	Sq.meter
175	2.74	To quote for supply of EPDM material D type fender of size 150mm X 02 meter, Quality Test certificate ( as per ISI standard ) from manufacturer to be provided	40	Meter
176	2.75	Engine side Defects
177	2.76	Sea chest / bilge & G.S. lines filters to be removed cleaned & to be boxed back with new SS nuts, bolts & gasket. Quote including cost of materials.	4	No
178	2.77	Following pipe lines in engine room, deck, are to be reomved, renewed with schedule 40 seamless pipeswith old Flanges. All the pipe line are to be welded along with flanges from both sides. The pipelines are to be painted and fitted back with new joints, Stainless steel nuts & bolts and supporting U- clamp whereever required. To quote Including cost of materials.
179	2.78	i) 80 mm to 100 bore	30	meters
180	2.79	ii) 55 mm to 75 mm bore	30	meters
181	2.8	iii) 30 mm to 50 mm bore	40	meters
182	2.81	New siren sea wether resistant to be installed,(3 Knot),230 volt. To quote Including cost of materials	1	Nos
183	2.82	Vent pipes on deck to be repaired/renewed.(Febricate). To quote Including cost of materials	3	Nos
184	2.83	Port side& Stbd wiper motor,arms,blade to be renewed as per sample.(TVS Lucas make ) with necessary modification in wheelhouse. To quote Including cost of materials.	2	Nos
185	2.84	Bilge pump electric supply systems to be repaired to make it operational. To quote Including cost of materials.	1	No
186	2.85	To quote for renewal of engine room shed size(3.5mtrx3.5mtr),including renewal of GI pipes and other consumables.To quote Including cost of materials	1	LS
187	2.86	To quote for renewal of aft blige tank manhole cover .To quote Including cost of materials.	1	No
188	2.87	To quote for renewal of hydraulic pipes( approximate total length 20meter and 08 nos),tank cleaning,renewal of Hydraulic filter and overhauling,revarnishing of motor 5KWand insulation upto 50Mohm,cable conceling GI pipe 15meter 1/2 inch dia with renewal of bearing.	1	LS
189	2.88	To quote for Renewal of engine room vents. (FRP type ).To quote Including cost of materials	2	Nos
190	2.89	Fuel oil tanks ( inside) to be cleaned properly & the manhole door to be fitted with new gaskets( Champion -3.15mm) (a) Storage tank –2500 ltr. To quote Including cost of materials	2	Nos
191	2.9	Diesel tank Gauge glass cocks 1/2” NB are to be removed, Overhauled & fifed back with Proper sealant, new ‘O’ rings &gaskets/glands. To quote Including cost of materials	2	Nos
192	2.91	To remove, dismantle, and Overhaul the following Overboard, Sea chest & intermediate valves of sea water pipeline:-After overhauling all the valves shall be pressure tested at 5 Kg/ sq.cm and fit back with new gasket, St. Steel nuts, bolts' joints., supporting clamps. \nTo quote Including cost of materials \n\n \n\n\n\n\n
193	2.92	1) Globe valve 50 NB	10	Nos
194	2.93	2) Globe valve 100 NB	12	Nos
195	2.94	3) SDNR. RT Angle Valve – 25 NB	8	Nos
196	2.95	4) fire hydrant Valve – 65 NB	2	Nos
197	2.96	5) Quick Closing Valves – 40 NB	2	Nos
198	2.97	6)Flap Valve (100NB)	1	Nos
199	2.98	7) Flap Valve (50 NB)	2	Nos
200	2.99	Both the Propellers are to be cleaned, Polished and Varnished. To quote Including cost of materials	2	Nos
201	3	To quote for repair of wheel house Electrical panel board.To quote Including cost of materials.	1	Ls
202	3.01	To quote for removal, overhauling , revarnishing of blower motor 02hp and fit back with new gasket,SS nut and bolts.	2	Nos
203	3.02	To quote for removal of all the checker plates & to fit with SS screws properly.To quote Including cost of materials.	1	Nos
204	3.03	To quote for supply and installation of 50 watt led light flood fitting IP66 in Engine room and steering room with necessary modification ( Make Havells, Bajaj, Philips, CG )	4	No
205	3.04	To quote for removal, overhauling,revarnishing of Alternator of D.G (port&stbd) 15KVA ,415 volts,50Hz and fit back with new nut and bolts with renewal of AVR and bearing. Insulation to be improved to 50Mohm	2	Nos
206	3.05	Rudder Unit: -To remove both the rudder shafts along with bushes and to be cleaning Properly, Shaft dia at bushes areas are to be machined by 02 mm and again built up with SS to MS welding rod and machined as per Bush ID, any ovality on Bushes to be machined and shaft to be fitted with new thrust bearing( SKF/Fag/NSK), SS studs ,nuts and gland packing.To quote including cost of materials,	2	Nos
207	3.06	Steering system to be overhauled including cleaning of tank , new hydraulic cylinder unit (travel=200mm,shaft dia =50mm) to be replaced as per sample with renewal of all fexisible hoses, limit switches, feedback unit, steering angle indicator etc. Hydraulic Hoses and connectors-a)3/8\"- 3.5ft= 2nos b) 3/8\"7ft - 4000psi=2nos c) 3/8\"5ft-4000psi=2nos d) 3/8\"*4.5ft- 4800psi-330bar=2nos ,manual steering to be overhauled.Quote including cost of materials.	1	Nos
208	3.07	New LED ceiling light with necessary modification in ceiling to be fitted in wheel house (15 watts). To quote including cost of materials.	4	No
209	3.08	To supply and install Deck Lights around wheel house ( water proof, IP-50, 9 watts) Havells/philips/bajaj/CG. Quote L. S.	14	No
210	3.09	To quote for supply and fitting of (100wt) led flood light in water tight casing ,IP 66 grade ( make - havells, bajaj , CG, philips,) To quote including cost of materials.	4	no
211	3.1	Controllable pitch propeller system to be flushed and oil to be renewed.Oil PPT supply	1	No
212	3.11	Slipway cradle
213	3.12	To quote for Grit blasting of entire cradle all the side by lifting the cradle to a height of 01 meter ,and surface prepared upto a standard of SA 2.5.	350	Sq.Mtrs.
214	3.13	To quote for Painting of entire cradle with 6coats of Epoxy Paint by airless spray (2Coats primmer+2coats sealer+2 coats Anti fouling/Finish). Paints PPT Supply.	350	Sq.Mtrs.
215	3.14	M/L Chandi and M/L Charchika
216	3.15	To quote for ML Charchika grit blasting of entire hull and main deck ,void spaces, steering room,engine room etc .both inner and outer including angles,frames etc plating up to the standard of SA 2.5	300	Sq.Mtrs.
217	3.16	To quote for Painting of above areas of ML Charchika with 6coats of Epoxy Paint by airless spray (2Coats primmer+2coats sealer+2 coats Anti fouling/Finish). Paint PPT Supply	300	Sq.Mtrs.
218	3.17	To quote for ML Chandi grit blasting of entire hull and main deck, void spaces, steering room,engine room etc . both inner and outer including angles,frames etc plating up to the standard of SA 2.5	300	Sq.Mtrs.
219	3.18	To quote for 'Painting of above areas of ML Chandi with 6coats of Epoxy Paint by airless spray (2Coats primmer+2coats sealer+2 coats Anti fouling/Finish). Paint PPT Supply	300	Sq.Mtrs.
220	3.19	To quote for Vulcanisation of cutlass bushes of ML Chandi and ML Charchika (size length 300 mm and ID 80 mm approximately) .To quote Including cost of materials.	8	Nos
221	3.2	Supply Items
222	3.21	To quote for supply of following Paints from OEM or its Authorised Dealers of Akzonoble Paints (International Brand) or Jotun or Sigma marine or Hempel :-
223	3.22	Epoxy Primer Intergard 269 or its equivalent Jotun /Sigma marine/Hempel.( 100ltr for ER )	400	ltrs
224	3.23	Epoxy anticorrosive Intertuf 262 or its equivalent Jotun / Sigma marine/Hempel.	380	ltrs
225	3.24	Epoxy Sealer Intergard 263 or its equivalent Jotun / Sigma marine/Hempel.( 100ltr for ER	380	ltrs
226	3.25	Epoxy Anti Fouling Interspeed 6200 or its equivalent Jotun / Sigma marine/Hempel.	160	ltrs
227	3.26	Top coat- 740-(Deck Green/white/grey) or Equivalent paint from Jotun or Sigma marine/Hempel for Eng. room and Deck .	380	ltrs
228	3.27	Epoxy Thinner GTA 220 or its equivalent Jotun / Sigma marine/Hempel.(40 ltr for ER )	260	ltrs
229	3.28	Anti Fouling Thinner GTA 007 or its equivalent Jotun / Sigma marine/Hempel.	40	ltrs
230	3.29	To quote for supply of Zinc Anodes fitted with MS welding arm (10.6 Kg. each) approx. with quality test certificate, Make: Sargam	50	Nos
231	3.3	To quote for supply of Zinc Anodes fitted with MS welding arm (5.5 Kg. each) approx. with quality test certificate. Make: Sargam	60	Nos
232	3.31	Note:1) The firm shall quote the prices including all taxes, transportation and other expenses towards execution of above works except GST. The GST shall be paid at the prevailing rate. 2) The firm shall quote prices for supply items limited to MRP. The firm shall submit the bill for the supply items along with MRP price list from the OEM or its authorised dealers .

Also Visit

Tenders

Odisha Tenders

Services Tenders

Transportation and Mailing Service Tenders

Vessel docking service Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Dry Docking / Repairs Of Pilot Launch Ml Biju Pattanaik , Survey Launch Ml Laxmi , Pollution Control Vessel Ml Kali , Mooring Launches Ml Chandi And Ml Charchika And Repairs Of Slipway Cradle Of Paradip Port Trust, Paradip-Odisha

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Dry Docking / Repairs Of Pilot Launch Ml Biju Pattanaik , Survey Launch Ml Laxmi , Pollution Control Vessel Ml Kali , Mooring Launches Ml Chandi And Ml Charchika And Repairs Of Slipway Cradle Of Paradip Port Trust, Paradip-Odisha

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us