Tender For Special Repair To Bldg No Op/T/211 And Provn Of Dining Hall For Or Of 165 Mh At Rms
Tender Value
17.40 Lakhs
Estimated cost
Bid Submission
26 Aug 2019
0 days left
EMD
34800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Rangapahar → Nagaland
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No Op / T / 211 And Provn Of Dining Hall For Or Of 165 Mh At Rms
BOQ
| Name of Work: : SPL REP TO BLDG NO OP/T/211 AND PROVN OF DINING HALL FOR OR OF 165 MH AT RMS (JOB NO:- RP/SR(B)/020/2018-19 AND RP/LBW/018/2018-19 ) | |||||
|---|---|---|---|---|---|
| Sl.No. | Item Description | Item Code / Make | Quantity | Units | |
| 1 | 1 | Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified | 25 | Sqm | |
| 2 | 2 | Excavation in trenches n.exc 1.5 m wide and n.exc 1.50m in depth n. exc 10 sqm on plan and getting out in soft/ loose soil ,complete all as specified and as directed. | 100 | Cum | |
| 3 | 3 | Returning, filling soil in trenches including spreading levelling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed. | 78 | Cum | |
| 4 | 4 | Removing excavated soil not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point all as specified and as directed. | 75 | Cum | |
| 5 | 5 | M&L for hard core of broken boulder or stone of gauge not exc 63 mm deposited , spread and levelled in layers n.exc 15cm thick watered and rammed to true surfaces complete all as specified and as directed. | 4 | Cum | |
| 6 | 6 | M&L Earth filling under floors Spreading and levelling in layers n exc. 25 cm thick and well ramming including watering as required complete all as specified and directed. | 6 | CUM | |
| 7 | 7 | Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15 cm thickness (below or above GL) and removing rubbish of the premises complete all as specified and as directed. | 1.8 | Cum | |
| 8 | 8 | M&L for P.C.C 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundation,filling and mass concrete all as specified and directed | 10.5 | Cum | |
| 9 | 9 | M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in footings, foundation including rafts, foundation beam, plinth beames; base for column etc ,basement slabs, under-reamed piles and mass concrete, complete all as specified and directed | 12 | Cum | |
| 10 | 10 | M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in columns, pillars, piers etc. complete all as specified and as directed. | 4 | Cum | |
| 11 | 11 | M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in beams, cantilevers, bressummers, lintels over 1.5 m span, complete all as specified and as directed. | 3 | Cum | |
| 12 | 12 | M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in as in slab supported on walls , beames and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc.complete all as specified and as directed. | 1 | Cum | |
| 13 | 13 | M&L for Reinforced cement concrete, M-25 design mix (Using 20 mm graded stone aggregate ) as in Chajjas, complete all as specified and as directed. | 0.3 | Cum | |
| 14 | 14 | M&L for pre-cast RCC 1:2:4 type B-1(using 20mm graded aggregate) as in manhole cover slab, landing,chullah hood, chajjas and similar article and set in cement mortar 1:4 including necessary from work and mould complete all as specified and as directed. | 0.12 | Cum | |
| 15 | 15 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits for foundation and plinth beams and similar work for rough finished surfaces of concrete, complete all as specified and directed | 60 | Sqm | |
| 16 | 16 | M&L for form work to sides of pillars, posts, sturts, piers, columns and similar work etc for rough finished square, rectangular or polygonal surfaces of concrete complete as specified and directed. | 55 | Sqm | |
| 17 | 17 | Use and waste of formwork to soffits of suspended slab such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick , rough finished surfaces of concrete, flate, complete all as specified and directecd. | 8.5 | Sqm | |
| 18 | 18 | Use and waste of formwork to sides and soffits of floor or roof beam , lintels, cantilever, shelves ,flate, rough finished surfaces of concrete, complete all as directed. | 15 | Sqm | |
| 19 | 19 | Use and waste of form work to soffits of chullah hoods, chajjas, troughs and similar items flat, rough finished surfaces of concrete complete all as directed. | 3 | Sqm | |
| 20 | 20 | Demolition of brick work or stone/boulder masonry built in cement mortar ,complete all as specified and directed. | 1.03 | Cum | |
| 21 | 21 | M&L for brick work with sub class ‘B’ bricks , straight or curved on plan exc 6 metre mean radius as in full brick thick walls built in CM(1:6) using old size bricks complete all as specified and as directed.\n | 23 | Cum | |
| 22 | 22 | M&L for brick wrok with sub-class 'B' bricks, straight or curved on plan to any radius, built in CM (1:4) using old size bricks in half brick thick walls complete all as specified and as directed. | 18 | Sqm | |
| 23 | 23 | M&L for Damp proof course of 25 mm thick cement concrete 1:2:4 type B-0 to horizontal or vertical surfaces including necessary formwork complete all as specified and as directed. (Concrete shall be admixed with Integral water proofing compound which shall be measured and paid separately as 'supply only). | 7 | Sqm | |
| 24 | 24 | Taking down shutters of any description exc 1 Sqm and n.exc 2 Sqm eachcomplete all as directed | 2 | Per Leaf | |
| 25 | 25 | S & F 12 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work, complete all as specified and directed. | 2 | Sqm | |
| 26 | 26 | S&F Anodised Aluminium work in any position such as door frames, window frames, grills , guard bars etc with one or more rebates incl necessary joining cleats for fixing etc complete all as specified and directed | 50 | KG | |
| 27 | 27 | S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, hinges anodised aluminium snap beading screws etc, complete all as specified and directed. | 5 | Sqm | |
| 28 | 28 | S&F Anodised aluminium window and ventilator shutters, sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed | 15 | Sqm | |
| 29 | 29 | S&F sheet glass 4.80mm thick ordinary quality and glazing with oil putty in squares exc .5 sqm each pane complete all as specified and directed. | 2 | Sqm | |
| 30 | 30 | S&F sheet glass 4.00 mm thick ordinary quality and glazing with oil putty in squares exc 0 .5 sqm each pane complete all as specified and directed. | 6 | Sqm | |
| 31 | 31 | S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed | 4 | Each | |
| 32 | 32 | S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed | 8 | Each | |
| 33 | 33 | S&F Harrison rails, stainless steel, 20 mm dia with fixing brackets, stops, rollers etc.complete all as directed | 14 | RM | |
| 34 | 34 | S&F mild steel galvanised wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed. | 2 | Sqm | |
| 35 | 35 | S&F double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless cover, governing pivot made of brass, other parts made of mild steel heavy duty , complete all as specified and as directed. | 2 | Each | |
| 36 | 36 | S&F for stainless steel wire cloth, 0.63mm nominal dia and average width of aperture 1.40 mm fixed with stainless steel wire staple including all cuttings, wastage etc complete as specified and directed. | 6 | Sqm | |
| 37 | 37 | Dismantling wrought iron or mild steel work of any description not other wise provided for complete all as specified and directed. | 1.05 | KG | |
| 38 | 38 | M&L TMT steel bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed. | 1300 | KG | |
| 39 | 39 | M&L TMT steel bars, 6 to 8 mm dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete as in reinforcement to concrete all as specified and as directed. | 250 | KG | |
| 40 | 40 | All as per serial item No 39.00 here -in-before but 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders. | 550 | Kg | |
| 41 | 41 | S&F mild steel work (miscellaneous) as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts, wall ties, hooks for hanging fans, plain angle cleats for securing purlines to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles conforming to Fe-290-Gde-E-165 complete all as specified and directed. | 52 | Kg | |
| 42 | 42 | S&F structural steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St 240 complete including painting with one shap coat of zinc chromate primer paint including preparation before febrication all as specified and as directed. | 1150 | Kg | |
| 43 | 43 | S & F Rolled mild steelplates( plain, or chequered) channel, square cut or notched, forming holes, with riveted , bolted or welded attachment conforming to Fe-410-W , complete all as specified and directed. | 45 | Kg | |
| 44 | 44 | S & F steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed. | 2.5 | Sqm | |
| 45 | 45 | S&F of MS screw bolts (Machine Made) 11 to 15 mm dia of shank with hexagonal and square heads at one end and screwed the other end and each screwed end to be fitted with washer and one square or hexagonal nuts exc 10 cm but n-exc 5 cm long complete all as specified and as directed. | 20 | KG | |
| 46 | 46 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings,complete all as directed. | 63 | Sqm | |
| 47 | 47 | S&F 0.63mm thick galvanised corrugated mild steel sheeting, with two corrugation side lap fixed with GI 'L' type or 'J' type or cranked hook bolts in roof, walls etc with grade of zinc coating as per IS complete all as specified and as directed. \n\n\n \n | 58 | Sqm | |
| 48 | 48 | S&F Plain galvanised mild steel sheeting 0.80mm thick galvanised as in ridges, hips valley, gutters and straight flushing, fixed with GI 'L' type or 'J' type or cranked hook bolts in roof, with grade of zinc coating as per IS complete all as specified and as directed.\n \n | 5 | Sqm | |
| 49 | 49 | S&F 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of any colour as approved of 550 Mpa tensile strength as in roof covering/ cladding to wall etc. fixed with self tapping screws complete as specified and directed | 90 | Sqm | |
| 50 | 50 | S&F 0.50 mm thick Prepainted galvalume aluminium zinc coating GI based plain steel sheet any colour as approved of 550 Mpa tensile strength as in ridges etc fixed with self drilling and self tapping screws, complete all as specified and directed. | 12 | Sqm | |
| 51 | 51 | Dismantling of wall and ceiling board of any description and any thickness including cover fillets , complete all as specified and as directed. | 52 | Sqm | |
| 52 | 52 | S&F S & F for HSPC (high pressure Steam Cured) pre-primetered self embossed, textured designer board E-Board, 4 mm thick of size 600x600mm,classic to be fixed aluminium grid/section size 600mmx600mm with main runner 38x24x0.9mm thick ,cross tee 28.6x24x0.9 mm and wall angle 19x19xo.9 mm duly suspended with 2mm dia GI bar hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size and finally applying two coats of oil bound distemper complete all as specified and directed. | 98 | Sqm | |
| 53 | 53 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as directed. | 48 | Sqm | |
| 54 | 54 | M&L for 75 mm PCC 1:4:8 type D-2 (using 40mm graded atone aggregate aggregate) as in sub base of floor, complete all as specified and as directed. | 50 | Sqm | |
| 55 | 55 | M&L for 75mm thick PCC 1:3:6 type C2 (using 40mm graded aggregate) as in paving/plinth protection , laid in alternate bays, finished the surface even and smooth without using extra cement complete all as specified and as directed. | 32 | Sqm | |
| 56 | 56 | M&L for 40mm thick PCC 1:2:4 type B1 (using 20mm graded aggregate) as in flooring finished the surface even and smooth without using extra cement complete all as specified and as directed. | 13 | Sqm | |
| 57 | 57 | M&L for 25 mm thick plain cement concrete 1:2:4, type B1, (using 20mm graded stone aggregate) as in levelling course complete all as specified and as directed.\n\n | 48 | Sqm | |
| 58 | 58 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.06 Sqm but not exc 0.11 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed. | 48 | Sqm | |
| 59 | 59 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular), area of each tiles exc 0.18 Sqm but not exc 0.38 Sqm in floors etc set and jointed in neat cement slurry and piinted in white/coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed | 50 | Sqm | |
| 60 | 60 | All as per item No 59.00 here in before but on vertical surfaces including rendering 10mm thick in cement mortar 1:4 , | 2 | Sqm | |
| 61 | 61 | M&L for glazed ceramic coloured tiles of size 300mm x 200mm x 7mm thick on vertical surfaces set and jointed in neat cement slurry and pointed in coloured cement to match with the existing, ,including 10mm thick rendering in cement mortar 1:4 complete all as specified and as directed. | 40 | Sqm | |
| 62 | 62 | M&Lfor 18 to 20 mm thick granite tiles (of any type), machine cut as in steps jambs, pillars, window cills, cooking platform & like bedded and jointed with gray cement slurry and pointed with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite , cutting and polishing, including 20 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed. | 5 | Sqm | |
| 63 | 63 | Taking down cement plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as directed. | 10 | Sqm | |
| 64 | 64 | M&L for 15mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:6 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed | 85 | Sqm | |
| 65 | 65 | M&L for 10 mm thick rendering on fair faces of brick or concrete surfaces in cement mortar 1:4 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed. | 10 | Sqm | |
| 66 | 66 | M&L for 15mm thick rendering in two layers of 10mm thick and 5mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 finished fair and even, using water proofing compound in top layer , complete all as specified and as directed (NOTE: WPC will be measured and paid separately as \"Supply only \" here in after) | 90 | Sqm | |
| 67 | 67 | M&L for 5mm thick rendering on fair faces of concrete surfaces as in ceiling in cement mortar 1:4 finished surfaces even and smooth (without using extra cement) complete all as specified and as directed. | 4 | Sqm | |
| 68 | 68 | Supply only integral water proofing compound of approved quality complete all as specified.\n\n | 15 | Kg | |
| 69 | 69 | M&L for preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and as directed. | 10 | Sqm | |
| 70 | 70 | M&L for preparation of newly plastered surface of wall and applying two coats of distemper oil emulsion over priming with chalk whiting , complete all as specified and as directed. | 75 | Sqm | |
| 71 | 71 | M&L for preparation on newly plastered surfaces on wall and applying two coats of cement based paint over priming coat of alkali resistant priming paint ,complete all as specified and as directed. | 75 | Sqm | |
| 72 | 72 | Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as directed. | 1.5 | Sqm | |
| 73 | 73 | S&F 3mm thick sheet glass , ordinary quality and glazing with oil putty in square n.exc 0.50 sqm each panes complete all as specified and as directed. | 1.5 | Sqm | |
| 74 | 74 | M&L for preparation of new steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying two coats of synthetic enamel paint (1st quality) over a coat of primer, complete all as specified and as directed. | 35.7 | Sqm | |
| 75 | 75 | M&L for preparation of old decorated steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, and applying one coat of synthetic enamel paint (1st quality) , complete all as specified and as directed. | 110 | Sqm | |
| 76 | 76 | S&F PVC connections pipe ,15mm dia size with PTMT nuts of length 450mm complete all as specified and as directed. | 2 | Each | |
| 77 | 77 | S&F vitreous china wash hand basin, white, flat back, size 550x 400 mm including a pair of MS brackets and cutting for pinning in ends of brackets but including chain and plug and porcelain stopper, MS chromium plated grating, PVC waste pipe complete all as specified and as directed. | 2 | Each | |
| 78 | 78 | S&F towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastics cleats (Minimum weight 170 gms). complete all as specified and directed. | 2 | Each | |
| 79 | 79 | S&F grating doom of size 100 mm dia PTMT , (Minimum weight 25 gm)complete all as specified and directed. | 2 | Each | |
| 80 | 80 | S&F PVC (SWR) floor trap plain with grating including jointing with solvent cement of diameter 75mm complete all as specified and as directed. | 2 | Each | |
| 81 | 81 | S&F for 600mm x 450mm beveled edge mirror of selected quality, glass, fixed to wooden plugs with chromium plated brass screws and cup washers, fixed in repair, complete all as specified. (MAKE : Saint Gobain/ Atul/ Goldfish/ Modi Guard) | 2 | Each | |
| 82 | 82 | M & L for Cement concrete 1:3:6 Type C-2 ,(using 20mm graded stone aggregate), as in surface channels and drains, etc., including use and waste of necessary Form Work, complete all as specified and as directed. | 1.5 | Cum | |
| 83 | 83 | Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed. | 45 | RM | |
| 84 | 84 | M&L for concrete bed to 150 mm bore SGSW drain pipes with PCC (1:3:6) type C2 (using 40mm graded stone aggregate) including packing under & haunching against the sides of pipes after they are laid, jointed and tested etc complete all as specified and as directed | 14 | RM | |
| 85 | 85 | M&L for 150mm bore salt glazed stone ware drain pipe, grade ‘A’ laid in trenches and jointed in cement mortar, tested complete as specified and directed. | 14 | RM | |
| 86 | 86 | S&F 75 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed. | 8 | RM | |
| 87 | 87 | S&F 110 mm PVC (SWR) pipe single socketed in any length with rubber ring joints ,fixed on wall , complete all as specified and as directed. | 6 | RM | |
| 88 | 88 | S&F 110 mm PVC (SWR) bends any radius provided with acess door complete all as specified and as directed | 2 | Each | |
| 89 | 89 | S&F 75 mm PVC (SWR) bends any radius provided with acess door complete all as specified and as directed | 2 | Each | |
| 90 | 90 | S&F 75 mm bore PVC (SWR) vent cowl ,complete all as specified and as directed. | 1 | Each | |
| 91 | 91 | S&F Stack clamps for 75 mm bore pipe made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed. | 4 | Each | |
| 92 | 92 | S&F 15mm dia steel water tubing, galvanised, medium grade, with all fittings and fixed to wall and ceiling or laid in floor in old/new position ,complete all as specified and as directed. | 15 | RM | |
| 93 | 93 | All as per item No 92.00 here-in-before but for 20 mm bore –ditto-. | 8 | RM | |
| 94 | 94 | S&F Bib tap, 15 mm bore , screwed for iron pipe for brass ferrule ,fixed in repair complete all as specified and directed. (MAKE:- Prayag Cat No 7306 or equivalent of make Cera/Hindware/ Century) | 2 | Each | |
| 95 | 95 | S&F pillar tap 15 mm bore,chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot' or 'Cold' long screwed shanks and fly-nuts screwed for iron pipe, complete all as specified and directed. (MAKE:- Prayag Cat No 7302or equivalent of make Cera/Hindware/ Century) | 2 | Each | |
| 96 | 96 | S&F angle Stop valves, 15mm bore, ,chromium plated, serewed down high pressure, with crutch or butter fly handle, for iron pipe or for union a , complete all as specified and directed. (MAKE:- Prayag or equivalent of make Cera/Hindware/ Century) | 2 | Each | |
| 97 | 97 | S&F rotational moulded polyethylene water storage tank (multilayer quality) cylindrical vertical with closed top of capacity 1000 liters hoisted and fixed in position with connecting ports (inlet, outlet and over flows ) , complete all as specified and as directed. | 1 | Each | |
| 98 | 98 | S & F Ball brass valves, 20 mm bore, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule , complete all as specified and directed. | 1 | Each | |
| 99 | 99 | S&F Gun-metal globe or gate valves, 20 mm bore, with iron wheel head, screwed both ends for iron pipe and fixed , complete all as specified and as directed. | 1 | Each | |
| 100 | 100 | M&L point wiring with, two single core, 1.5 Sqmm (nominal area) size multistranded FRLSH copper conductor cable and one single core 1.5 Sqmm (nominal area) size solid copper conductor cable using colour code as phase , Neutral and as Earth continuity conductor connected to common earth dolly, 1100 volts grade ,PVC insulated, unsheathed cable drawn through and including PVC casing capping and PVC boards with all fittings and fixing materials for one Light /Fan point controlled by one no one way switch all as specified and directed. | 25 | Point | |
| 101 | 101 | All as per item No 100.00 here-in-before but for one 3 pin socket outlet 5 Amps independent board | 2 | Point | |
| 102 | 102 | All as per item No 100.00 here-in-before but for one 3 pin socket outlet 5 Amps on same board with other switch | 6 | Point | |
| 103 | 103 | All as per item No 100.00 here-in-before but but with cable size 2.5 Sqmm for one 5 pin 15 Amps socket outlet on independent board and multistranded insulated copper earth continuity conductor of size 1.5 Sqmm all as specified and directed by Engineer-in-Charge | 4 | Point | |
| 104 | 104 | S&F switch piano, flush type, 5Amp, single pole, one way white colour conforming to IS and/or as approved by GE,complete all as specified and as directed. | 31 | Each | |
| 105 | 105 | S&F flush type socket outlet , 2 in 1, 3 pin , 5 Amps, 230 volt, conforming to IS and/or as approved by GE, complete all as specified and directed. | 8 | Each | |
| 106 | 106 | S&F Switch socket combination , 2 in 1, 5 Amps/16 Amps flush type, 230 volt, conforming to IS and/or as approved by GE, complete all as specified and directed. | 4 | Each | |
| 107 | 107 | S&F fan regulator electronic step type, 230V 50Hz ,conforming to IS and/or as approved by GE, complete all as specified and as directed. | 7 | Each | |
| 108 | 108 | S&F L for ceiling rose, surface type, PVC/ polycarbonate body with ruond back plate, three terminals, conforming to IS and/or as approved by GE, complete all as specified and as directed. | 19 | Each | |
| 109 | 109 | S & F Ceiling fan, 1200 mm sweep , suitable for 230 volts, 50 Hz including provision of down and other accessories ( without regulator ) and connecting up Electrically with new Flexible Copper Cable, size as ordered, complete all as directed.\nMAKE :- ORIENT/ BAJAJ / USHA/ POLAR)\n | 7 | Each | |
| 110 | 110 | S&F Sub main wiring with 2 runs of single core, 4 Sqmm PVC insulated, unsheathed, 1100 volts grade multi-stranded, copper conductor cables FRLS , drawn through and including PVC casing caping, PVC board with all fitting including 2.5 sqmm copper conductor as earth continuity wire ,complete as specified and directed. (Note : Two runs of cable and one run of earth wire shall be measured as one run length)\n | 50 | RM | |
| 111 | 111 | S & F MCB SPN 6 to 32 Amps rating ,240 volts grade , \" C\" curve , conforming to IS and/or as approved by GE,including taking down the old one, complete all as specified and directed .(Make : Legrand/Schneider/L&T) | 1 | Each | |
| 112 | 112 | S & F MCB SPN 63 Amps rating ,240 volts grade , \" C\" curve , conforming to IS and/or as approved by GE,including taking down the old one, complete all as specified and directed .(Make : Legrand/Schneider/L&T) | 1 | Each | |
| 113 | 113 | S&F MCB, SP, 6 to 32 Amps rating ,240 volts grade , \" C\" curve , conforming to IS and/or as approved by GE, including taking down the old one,complete all as specified and directed .(Make : Legrand/Schneider/L&T) | 8 | Each | |
| 114 | 114 | S & F MCB DB Single pole and neutral 8 way sheet steel phospetised powder painted with 200 amps rated bus bar 240 V neutral link, earth bar and Din rail double door including taking down the old one, complete all as specified and directed\n(Make : Legrand/Schneider/L&T) | 1 | Each | |
| 115 | 115 | S & F MCB DB Single pole and neutral 4 way sheet steel phospetised powder painted with 200 amps rated bus bar 240V neutral link, earth bar and Din rail double door complete all as specified and directed\n(Make : Legrand/Schneider/L&T) | 1 | Each | |
| 116 | 116 | M&L for earthing with galvanized steel earth plate 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connected to galvanized iron earth wire 4 mm as earthing lead by means of bolts nuts check-nuts and washers of galvanized iron or steel besides welding at all joints as shown in drawings and including excavation and earth work GI pipe light grade 15mm bore for protection of GI wire from earth electrode to earth dolly including earth test point of galvanized iron or steel of size 75x75x25 mm supplying and laying char coal dust, common salt PCC 1:2:4 type B-1 chamber and MS angle frame 40 x 40 x 3 mm and RCC cover 40 mm thick (1;2:4) type B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia GI funnel and wire mesh 20 mm dia GI pipe light grade for watering all as shown in drawing and connected to earth test point including testing complete all as specified and directed. | 1 | Each | |
| 117 | 117 | S & F Wall mounted LED batten 20 watt extruded aluminium heat sink provided for efficient heat dissipation & integrated\nelectronic driver with all accessories, pre-wired connecting up with new flexible copper cable of size 0.75 Sqmm, 3 core , complete all as specified and directed.\n( Make- Havells Ordering Code No LHFXCEP1TN1W020 (Batten) , LHEXCEP7UN1W020 (LED bTube)or equivalent in Philips/Bajaj) | 10 | Each | |
| 118 | 118 | S & F Wall mounted LED batten 10 watt extruded aluminium heat sink provided for efficient heat dissipation & integrated\nelectronic driver with all accessories, pre-wired connecting up with new flexible copper cable of size 0.75 Sqmm, 3 core , incl taking down existing unserviceable one, complete all as specified and directed.\n( Make- Havells Ordering Code No LHEXBXPNIN1W010 or equivalent in Philips/Bajaj) | 2 | Each | |
| 119 | 119 | S & F Security light LED 20 watt made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 including suitable size of street light bracket made out of 25 mm bore GI pipe, light grade 1.2 metre in length, made to shape as required, fixed to pole with MS flat iron clamp of size 25x4mm duly welded, bent to shape and making holes etc including necessary nuts, bolts & washer etc fixed in repair complete all as specified and directed.\n( Make- Havells Ordering Code No LHETA XU7PA6S020 or equivalent in Philips/Bajaj) | 2 | Each | |
| 120 | 120 | Supply and laying well burnt brick, Sub class ‘B’, old size as in cable protection, laid across in trenches complete all as specified and directed. | 560 | Each | |
| 121 | 121 | M&L sand cushioning with approved fine grade sand for protection of under ground cable complete all as specified and as directed NOTE : Finished measurement after punning down shall be considered for payment. | 3 | Cum | |
| 122 | 122 | Supply, laying, connecting and testing XLPE insulated (Earthed) cable in trenches/or fixed on pole etc in screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) with stranded aluminium conductor, 1100 Volt grade, cross sectional area 25 Sqmm, 2 Core Conforming to IS-7098 (Part-II)-1985 including taking up/down unsv under ground cable, complete all as specified and directed.(Note: Excavation & earth work shall be measured and paid separately) | 50 | RM | |
| 123 | 123 | S&F galvanised iron tubing, 40 mm bore , light grade with all fittings for passing of under ground cable as in cable protection, complete all as specified and as directed. | 6 | RM | |
| 124 | 124 | S&F galvanised iron tubing, 25 mm bore , light grade with all fittings , fixed to wall ,ceiling or or laid in floor for passing of under ground cable as in cable protection, complete all as specified and as directed. | 25 | RM | |
| 125 | 125 | S&F floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete as specified and directed. | 4 | Each | |
| 126 | 126 | S&F 150 mm dia mild steel sheet eaves gutters of 1 mm thick, galvanized, class 3, half round ,complete all as specified and as directed. | 30 | RM |
AI Tender Summary
Tender Timeline
Aug 14, 2019
11:30 IST
Tender Published
Tender notice published.
CompletedAug 26, 2019
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedAug 28, 2019
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender