| 1 | 1 | A) M.V. SHUNYA | | | |
|---|
| 2 | 2 | Overhauling of hopper door hydaulic cylinder - 2 & 4 nos. | | 2 | Nos. |
|---|
| 3 | 3 | Renewal of Mild steel seamless pipe of hydraulic cylinder 2nd nos cylinder | | 1 | Nos. |
|---|
| 4 | 4 | Supply & fitment of exhaust fan in the toilet | | 1 | Nos. |
|---|
| 5 | 5 | Repairs to broken kitchen platform kadapa by fitting new kadapa as per original size. 4ft 2inch long x 2ft width x 20mm | | 1 | Job |
|---|
| 6 | 6 | Repairs to Blower on the top by removing pitted sheet and fitting new m.s.plate as perequired . | | 1 | Job |
|---|
| 7 | 7 | Providing and fitting new mast Light | | 1 | Nos. |
|---|
| 8 | 8 | Fabricating and fitiing new hatch cover of 2feet 9 ïnch & 2feet 2ïnch in size - for the ballast tank as per original size. | | 3 | Nos. |
|---|
| 9 | 9 | Carrying out repairs to bend Railing by cutting pipe and welding new 2\" dia.and 1mtr.long m.s. Pipe as per original shap. | | 1 | Job |
|---|
| 10 | 10 | Providing and fitting lock for door of wheelhouse cabin - 1no. and for Engine room cabine - 2nos. | | 1 | Job |
|---|
| 11 | 11 | Replacement of diesel pipe of port & stbd diesel tank | | 2 | Job |
|---|
| 12 | 12 | Replacemnet of RPM meter cable of Port engine | | 1 | Job |
|---|
| 13 | 13 | Supply of oil & diesel filter of Cummins engine of port and stbd engine- 2Set & Simpson generator - 2 Set | | 1 | Job |
|---|
| 14 | 14 | Servicing of Anchor Motor | | 1 | Job |
|---|
| 15 | 15 | Servicing of simpson generator port side | | 1 | Job |
|---|
| 16 | 16 | Supply and fitment of gauges, speedometer, presure & temperature gauge of simpson generator | | 1 | Job |
|---|
| 17 | 17 | Servicing of fire pump | | 2 | Nos. |
|---|
| 18 | 18 | Steering Normal & Emergency system corroded V/V s & pipes and etc. to be renewed. | | 2 | Nos. |
|---|
| 19 | 19 | B) M.V. BODDHE | | | |
|---|
| 20 | 20 | Machining of ‘T’ shape hydraulic cylinder locking pin of high tensile mild steel of size 42mm dia x 600mm height with 100 mm dia x 25mm thickness head on one end. MS round bar of 12mm dia x 150 mm to be welded on top of the pin head for holding the pin in vertical position during operation. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 4 | Nos. |
|---|
| 21 | 21 | Providing & fitting 220V new fan in place of old burnt fans in Master cabin, Engine Driver cabin & Crew cabin. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 5 | Job |
|---|
| 22 | 22 | Checking of GPS, Echo sounder & VHF including rectification of defects proper operation. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 23 | 23 | Port side bilge pipe to be removed, cracked portion to be renewed with schedule 40 pipe as per required shape & size and same to be re-fitted back in its original position with new joints and nut-bolts with washers. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 24 | 24 | Starboard side gear oil cooler inlet & outlet old deteriorated cracked rubber hoses to be replaced with new rubber hoses (APS) and SS jubilee clips. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 25 | 25 | Servicing/repair of Port M/E dynamo for overhauling (including renewal of bearings, checking of shaft trueness, checking continuity winding, insulation testing, etc.) greasing and re-varnishing with submission of report of all checks carried out and checking for proper functioning on load. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 26 | 26 | Engine Room Supply blower – Blower motor (5 HP) to be checked & overhauled (including renewal of bearings, checking of shaft trueness, checking continuity of winding, insulation testing including report, etc.) re-varnishing, greasing & to be made operational and satisfactory trials to be given. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 27 | 27 | Starboard Auxiliary Engine - Providing & fitting new RPM gauge (APS) in place of old defective RPM gauge. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 28 | 28 | Port Main Engine (Cummins NTA 855) - Providing & fitting new RPM gauge (APS) in place of old defective RPM gauge. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 29 | 29 | Port Main Engine (Cummins NTA 855) – Oil leakage from No.1 cylinder head. Suspect cylinder head gasket leakage, same to be replaced with new gasket, cylinder head to be pressure tested, tappet setting to be checked. All lub oil & fuel filters to be renewed. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 30 | 30 | Starboard Main Engine – Oil filter leakage. Filter ‘o’ ring & filter to be renewed. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 31 | 31 | Cleaning the storage batteries, refilling with new Acid solution and recharging to full capacity. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 8 | nos |
|---|
| 32 | 32 | Crew Cabin Carpentry Job : The following material required to be used for the jobs at Sr. 33 to 36 :-\nTotal Area – 20’ x 8’ x 7’ x 4 nos. \n• Decolite - 8’ x 4’ x 6mm x 21 nos.\n• Salwood frame patti – 2” x 1 ½” x 8’ x 130 nos.\n• Aluminium patti – 1” x 250 Rft\n• Marine plywood – 8’ x 3’ x 12mm x 3 nos.\n• Sal wood – 3” x 12 mm | | | |
|---|
| 33 | 33 | Crew cabin all side’s & ceiling’s dried & deteriorated plywood with wooden paneling to be removed and complete area to be cleaned thoroughly. New square shape wooden frames are to be made from teak wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 34 | 34 | 7 nos. crew beds are to be repaired as required and new 6’ x 3’ x 12 mm marine plywood with wooden baton patti to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 35 | 35 | 5 nos. window’s deteriorated wooden border patti to be renewed with new 3” sal wood wooden patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 36 | 36 | 2 nos. wooden cupboard’s damaged top to be repaired as required. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 37 | 37 | Master Cabin Carpentry Job : The following material required to be used for the hobs at Sr. 38 to 40 :- Decolite - 8’ x 4’ x 6mm x 9 nos. · Salwood frame patti – 2” x 1 ½” x 8’ x 50 nos. · Aluminium patti – 1” x 140 Rft· Marine plywood – 8’ x 3’ x 12mm x 1no. Sal wood – 3” x 12 mm | | | |
|---|
| 38 | 38 | Master cabin all side’s & ceiling’s dried & deteriorated plywood with wooden paneling to be removed and complete area to be cleaned thoroughly. New square shape wooden frames are to be made from teak wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads. ( Side Area – 7’ x 6 ½’ x 7’, ceiling area – 8’ x 7) | | 1 | Job |
|---|
| 39 | 39 | 1 no. bed box top deteriorated plywood to be renewed with new 6’ x 3’ x 12 mm marine ply & all side sal wood baton patti of 2” x 2 ½“ x 6 ‘ to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 40 | 40 | Window’s damaged wooden border patti to be renewed completely. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 41 | 41 | Passage Area Carpentry Job : Passage Area – Sides : 7’ x 7’ x 2nos. & 3’ x 7’ x 2 nos.,Ceiling : 7’ x 3’ All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Decolite - 8’ x 4’ x 6mm x 7 nos., Salwood frame patti – 2” x 1½” x 8’ x 20 nos., Aluminium patti – 1” x 60 Rft | | 1 | Job |
|---|
| 42 | 42 | 1 no. door frame to be renewed using salwood patti of 3” x 2” x 3 nos. & border salwood patti of 2” x 1½”& 1½” x ½” x 32’. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 43 | 43 | Kitchen Room Carpentry job : Kitchen Room – (Side area : 8’ x 7’ x 2nos, 6½’ x 7’ x 2 nos. Ceiling area : 8’ x 6½’) All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Becolite Ply - 8’ x 4’ x 6mm x 10 nos., Aluminium patti – 1” x 150 Rft | | 1 | Job |
|---|
| 44 | 44 | Dining table to be repaired as required. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 45 | 45 | Damaged broken window to be repaired completely. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 46 | 46 | Engine Driver Cabin Carpentry Job : Engine Driver Cabin – (Side area : 8’ x 7’ x 2nos., 6½’ x 7’ x 2 nos. Ceiling area : 8’ x 7’) Cabin’s all sides & ceiling dried & deteriorated plywood with wooden paneling to be removed &complete area to be cleaned thoroughly. New square shape wooden frames are to be made from sal wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Becolite Ply - 8’ x 4’ x 6mm x 10 nos., Salwood frame patti – 2” x 1½” x 8’ x 50nos, Aluminium patti – 1” x 130 Rft. | | 1 | Job |
|---|
| 47 | 47 | 1 no. bed box top deteriorated plywood to be renewed with new 6’ x 3’ x 12 mm marine ply & all side sal wood baton patti of 2” x 2 ½“ x 6 ‘ to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 48 | 48 | 01 no. cupboard damaged broken plywood to be renewed with marine ply of 6’x3’x19mm along with border wooden patti of 1”x 1½” and 1” x 1”. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 49 | 49 | Window’s damaged broken side border to be renewed with new wooden patti of 3” x 8’. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 50 | 50 | Bath Room & Toilet Passage Area Carpentry Job : Bath Room & Toilet Passage Area – All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Decolite - 8’ x 4’ x 6mm x 4 nos., Salwood frame patti – 2” x 1½” x 8’ x 20 nos., Aluminium patti – 1” x 30 Rft. | | 1 | Job |
|---|
| 51 | 51 | 02 nos. deteriorated & dried doors of bath room & toilet required to be renewed with new marine plywood of 6’ x 4’ x 30mm along with frames of 3” x 2” x 7’ x 5 nos. wooden patti, 50 Rft Salwood border patti of 2” x 1½” & 1 ½” x ½” and 6 nos. brass hinges with screws. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 52 | 52 | Defective drawer locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 10 | Nos. |
|---|
| 53 | 53 | Round type defective door locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 5 | Nos. |
|---|
| 54 | 54 | Handle type defective door locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 6 | Nos. |
|---|
| 55 | 55 | C) M.V. NIRVAN | | | |
|---|
| 56 | 56 | Anchor Winch Motor – Servicing of anchor winch motor for overhauling (including renewal of bearings, checking of shaft trueness & required repair, checking continuity of winding, insulation testing, overhauling of contactor, renewal of terminal box gasket, etc.), re-varnishing, greasing to be carried out. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 57 | 57 | Stanchions Repair – Main deck Stbd side stanchion’s 12 nos. vertical support flat bar’s corroded, worn out/damaged bottom portion to be renewed with new flat bar of 100mm x 100 mm x 8 m x 12 nos. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 58 | 58 | Complete Engine room lighting to be checked for proper operation. Defective light points to be made operational with necessary repairs using required material such as wire, holders, switches etc. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 59 | 59 | Stab side defective halogen light to be repaired including renewal of defective spares and to be made operational. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 60 | 60 | Diesel pump motor trips during running, same to be checked and defect to be rectified with necessary repairs (including renewal of bearings, checking of shaft trueness, checking continuity of winding, insulation testing, re-varnishing, greasing, etc.). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 61 | 61 | Port Main Engine – Fresh water cooler to be cleaned & damaged tubes, if any, to be plugged. Then cooler to be pressure tested & report to be submitted. Cooler to be fitted back with new gaskets & rubber hoses. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 62 | 62 | Port gear box out put shaft & propeller shaft coupling broken nut bolt to be replaced with new nut-bolt & washer (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 63 | 63 | Port & Stbd Main Engine sea water pumps are to be overhauled (including bearings renewal, shaft trueness checking & repairs if any, impeller repairs/renewal, belts renewal) & to be fitted back with new gaskets, nut-bolts. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 2 | Nos |
|---|
| 64 | 64 | Servicing of Starboard Main Engine alternator for overhauling, greasing and varnishing including renewal of items required to make the alternator operational and checking for proper functioning on load. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 65 | 65 | Port and Starboard auxiliary engine’s leaking flexible wire braided diesel hoses to be renewed with new hoses (APS). Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 66 | 66 | Port auxiliary engine sea water pump to be overhauled (including bearings renewal, shaft trueness checking /repairs, impeller renewal, belts renewal) & to be fitted back with new gaskets, nut-bolts. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 67 | 67 | Port & starboard auxiliary engine’s sea water pump’s cracked rubber hoses to be renewed with new hoses (APS) & jubilee clips. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 68 | 68 | Starboard Auxiliary Engine – Engine starting problem and vibrates while stopping. Defect to rectified after thorough investigation. Starter to be checked & serviced including renewal of necessary spares. Fuel pump to be checked & serviced including renewal of necessary spares. Solenoid valve to be checked for proper functioning & renewed. Fuel injectors to be pressure tested & serviced including renewal of necessary spares. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 69 | 69 | Port Auxiliary Engine – Engine vibrates while starting. Defect to rectified after thorough investigation. Starter to be checked & serviced including renewal of necessary spares. Fuel pump to be checked & serviced including renewal of necessary spares. Solenoid valve to be checked for proper functioning & renewed. Fuel injectors to be pressure tested & serviced including renewal of necessary spares. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 70 | 70 | Crew Cabin Carpentry Job : The following material required to be used for the jobs at Sr. 71 to 74 :- Total Area – 20’ x 8’ x 7’ x 4 nos Decolite - 8’ x 4’ x 6mm x 21 nos. Salwood frame patti – 2” x 1 ½” x 8’ x 130 nos. Aluminium patti – 1” x 250 Rft Marine plywood – 8’ x 3’ x 12mm x 3 nos. Sal wood – 3” x 12 mm | | | |
|---|
| 71 | 71 | Crew cabin all side’s & ceiling’s dried & deteriorated plywood with wooden paneling to be removed and complete area to be cleaned thoroughly. New square shape wooden frames are to be made from teak wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 72 | 72 | 7 nos. crew beds are to be repaired as required and new 6’ x 3’ x 12 mm marine plywood with wooden baton patti to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 73 | 73 | 5 nos. window’s deteriorated wooden border patti to be renewed with new 3” sal wood wooden patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 74 | 74 | 2 nos. wooden cupboard’s damaged top to be repaired as required. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 75 | 75 | Master Cabin Carpentry Job : The following material required to be used for the jobs at Sr.76 to 78 :- Decolite - 8’ x 4’ x 6mm x 9 nos, Salwood frame patti – 2” x 1 ½” x 8’ x 50 nos., Aluminium patti – 1” x 140 Rft, Marine plywood – 8’ x 3’ x 12mm x 1no., Sal wood – 3” x 12 mm | | | |
|---|
| 76 | 76 | Master cabin all side’s & ceiling’s dried & deteriorated plywood with wooden paneling to be removed and complete area to be cleaned thoroughly. New square shape wooden frames are to be made from teak wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads.(Side Area– 7’x6 ½’x7’, ceiling area – 8’x 7’) | | 1 | Job |
|---|
| 77 | 77 | 1 no. bed box top deteriorated plywood to be renewed with new 6’ x 3’ x 12 mm marine ply & all side sal wood baton patti of 2” x 2 ½“ x 6 ‘ to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 78 | 78 | Window’s damaged wooden border patti to be renewed completely. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 79 | 79 | Passage Area Carpentry Job : Passage Area – Sides : 7’ x 7’ x 2nos. & 3’ x 7’ x 2 nos., Ceiling : 7’ x 3’ All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Decolite - 8’ x 4’ x 6mm x 7 nos., Salwood frame patti – 2” x 1½” x 8’ x 20 nos., Aluminium patti – 1” x 60 Rft | | 1 | Job |
|---|
| 80 | 80 | 1 no. door frame to be renewed using salwood patti of 3” x 2” x 3 nos. & border salwood patti of 2” x 1½”& 1½” x ½” x 32’. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 81 | 81 | Kitchen Room Carpentry Job : Kitchen Room – (Side area : 8’ x 7’ x 2nos, 6½’ x 7’ x 2 nos.) Ceiling area : 8’ x 6½’) All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Becolite Ply - 8’ x 4’ x 6mm x 10 nos., Salwood frame patti – 2” x 1½” x 8’ x 45nos. Aluminium patti – 1” x 150 Rft | | 1 | Job |
|---|
| 82 | 82 | Dining table to be repaired as required. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 83 | 83 | Damaged broken window to be repaired completely. Charges includes cost of material, consumables, transportation & labour charges with lift-leads. | | 1 | Job |
|---|
| 84 | 84 | Engine Driver Cabin – (Side area : 8’ x 7’ x 2nos., 6½’ x 7’ x 2 nos. Ceiling area : 8’ x 7’) Cabin’s all sides & ceiling dried & deteriorated plywood with wooden paneling to be removed &complete area to be cleaned thoroughly. New square shape wooden frames are to be made from sal wood of 2” x 1 ½” and to be fitted on all sides & ceiling of the cabin. Decolite sheet of 8’ x 4’ x 6mm are to be fitted on frames with SS screws. 1” alluminium patti to be fitted between two adjacent sheets. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Becolite Ply - 8’ x 4’ x 6mm x 10 nos., Salwood frame patti – 2” x 1½” x 8’ x 50nos, Aluminium patti – 1” x 130 Rft. | | 1 | Job |
|---|
| 85 | 85 | 1 no. bed box top deteriorated plywood to be renewed with new 6’ x 3’ x 12 mm marine ply & all side sal wood baton patti of 2” x 2 ½“ x 6 ‘ to be fitted. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 86 | 86 | 01 no. cupboard damaged broken plywood to be renewed with marine ply of 6’x3’x19mm along with border wooden patti of 1”x 1½” and 1” x 1”. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 87 | 87 | Window’s damaged broken side border to be renewed with new wooden patti of 3” x 8’. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 88 | 88 | Bath Room & Toilet Passage Area – All sides & ceiling dried & deteriorated plywood with frames to be removed & area to be cleaned thoroughly. New frames to be made & fitted as per required size & shape. New decolite sheet to be fitted along with alluminium patti. Charges includes cost of material, consumables, transportation & labour charges with lift leads. The following material required to be used :- Decolite - 8’ x 4’ x 6mm x 4 nos., Salwood frame patti – 2” x 1½” x 8’ x 20 nos., Aluminium patti – 1” x 30 Rft. | | 1 | Job |
|---|
| 89 | 89 | 02 nos. deteriorated & dried doors of bath room & toilet required to be renewed with new marine plywood of 6’ x 4’ x 30mm along with frames of 3” x 2” x 7’ x 5 nos. wooden patti, 50 Rft Salwood border patti of 2” x 1½” & 1 ½” x ½” and 6 nos. brass hinges with screws. Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 1 | Job |
|---|
| 90 | 90 | Defective drawer locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 10 | Nos |
|---|
| 91 | 91 | Round type defective door locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 5 | Nos |
|---|
| 92 | 92 | Handle type defective door locks are to be replaced with new locks (APS). Charges includes cost of material, consumables, transportation & labour charges with lift leads. | | 6 | Nos |
|---|
| 93 | 93 | D) MV AAHARAK | | | |
|---|
| 94 | 94 | Overhauling of hopper door hydaulic cylinder - 2&3nos | | 2 | Nos |
|---|
| 95 | 95 | Repairs to hopper door puliey bracket | | 1 | Job |
|---|
| 96 | 96 | Servicing of Anchor Motor | | 1 | Job |
|---|
| 97 | 97 | Repairs to broken kitchen platform kadapa by fitting new kadapa as per original size and repairs to kitchen troly. | | 1 | Job |
|---|
| 98 | 98 | Carrying out repairs to bend Railing by cutting pipe and welding new 2\" dia.and 1mtr.long m.s. Pipe as per original shap. | | 1 | Job |
|---|
| 99 | 99 | Providing and fitting lock for door of wheelhouse cabin - 2no. and for Engine room cabine - 1nos. | | 3 | Nos |
|---|
| 100 | 100 | Providing new of sea water pump of port and stbd generator. | | 2 | Nos |
|---|
| 101 | 101 | Complete wiring checking of AC and DC electric wiring from main panel board to various user sources. Rectification of defect if any usng sunery materials. | | 1 | Job |
|---|
| 102 | 102 | Providing 480 kg. Anchor-1no. | | 1 | Nos |
|---|
| 103 | 103 | Providing new fans - 6 nos. In crew accumodation. | | 6 | Nos. |
|---|
| 104 | 104 | Replacemnet of RPM meter of Port engine -1no and in wheel house- 1no. | | 2 | Nos. |
|---|
| 105 | 105 | Supply and fitment of gauges, speedometer, presure & temperature gauge of simpson generator of port & stbd side. | | 1 | Job |
|---|
| 106 | 106 | Checking bilge pump line and rectifing any defect if any. | | 1 | Job |
|---|
| 107 | 107 | Supply and fitment of gauges, speedometer, presure & temperature gauge of port & stbd side engine. | | 1 | Job |
|---|
| 108 | 108 | Complete checking and serviving of fuel pump and injector of stbd generator. | | 1 | Job |
|---|
| 109 | 109 | Providing anad fitting oil seal for stbd generator. | | 1 | Job |
|---|
| 110 | 110 | Checking and servicing of alternator of port and stbd main engine. | | 1 | Job |
|---|
| 111 | 111 | Checking port generator for high voltage. | | 1 | Job |
|---|
| 112 | 112 | Supply of oil & diesel filter of Cummins engine of port and stbd engine- 2Set & Simpson generator - 2 Set | | 1 | Job |
|---|
| 113 | 113 | Removing broken glass in the crew room and providing and fitting new glass of size apprx. 18 inch x 15 inch. | | 1 | Job |
|---|
| 114 | 114 | checking leakage supply of hydraulic oil near hydraulic tank and rectifying defect. | | 1 | Job |
|---|
