BRR : 7585692 Tender For Replacing Defective Roof Sheets And Accessories Of Various Sheds Of Nfc Hyderabad.; 1 EARTH WORK: 2 Felling down carefully trees of girth (measured at a height of 1.0m above ground level) as mentioned below including necessary excavation, removal / destruction of roots, filling the excavated pockets thus formed with good earth, compacting the same, cutting the trunks and branches of trees into suitable pieces for transporting, transporting, stacking and disposing the same at the locations as directed by Engineer - in - Charge, etc., complete. 3 Beyond 60 cm girth upto and including 120 cm girth 4 Beyond 120 cm girth upto and including 240 cm girth 5 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared etc. complete as specified and directed. 6 ROOF SHEET AND CLADDING WORK: 7 Supplying and fixing new Fibre Reinforced Cement Corrugated sheets, 6mm thick of Charminar/ Visakha/ everest make conforming to IS 459 and laying as per IS 3007 at various elevations in areas as given below using necessary safety nets, Roof walk ladders and other standard safety devices including all overlaps, mitring, fixing the sheets with necessary 8mm dia polymer coated self tapping/ self drilling screws required length, including GI & EPDM washers as per manufactures code of Practice and cutting the sheets as required etc., removing and refixing of sorrounding sheets, complete all as directed by Engineer-in-Charge. NOTE : 1. Payment will be made for area of sheets replaced, NOT for quantity of sheets removed and refixed.2. Replacing roof sheets shall be done by following all safety procedures including requirement of working personnel having valid height pass, use of double lanyard safety belts hooked to lifelines and all as per guidelines of Engineer-in-charge. 8 Area of replaced sheets is upto 30 Sq.m. 9 Area of replaced sheets is beyond 30 Sq.m. 10 Polycarbonate sheets of 2.0mm thick, pressed to matching through corrugations of roofing of GE/TUFFLITE equivalent make (as approved by Engineer-in-charge) for Sky lights including sealing around sheetswith GE/TUFFLITE siliconates or any other sealant, treating for rainproof, fixing sheeting with SS or polymer coated self tapping screws, EPDM & GI washers etc., complete as directed by Engineer-in-charge 11 Providing and fixing in position approved quality weather tight accessories such as RIDGES (PAIR), in required shape and profile made of fibre reinforced cement including neessary cutting, profiling, sealants, flat iron buckets, EPDM/beadings etc all complete in accordance with approved manufactures standard practice using all appropriate safety devises and following safety procedures as directed by Engineer-in-Charge. 12 Providing and fixing in position approved quality weather tight accessories such as CORNER PIECE/ NORTH LIGHT CURVE, various types of flashing, gutters (including straps), trims in roofing, cladding in required shape and profile made offibre reinforced cement corrugated sheets including necessary cutting , profiling, sealant, flat iron buckets, EPDM/beading etc all complete in accordance with approved manufacturers standard practice and as directed by Engineer in charge. 13 Making groove not less than 50mm deep in brickwork at gable end of the buildings for removing the damaged roofing sheets, inserting the new/existing fiber reinforced cement corrugated sheet into the groove on cement mortar bed and filling the groove with cement mortar 1:4 admixed with approved water proofing compound at dose as recommended by manfacturer, finishing it smooth including all tools, required steel scaffolding etc., complete as directed by Engineer-in-charge. 14 Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge .The elevational area of the scaffolding shall be measured for payment purpose .The payment will be made once irrespective of duration of scaffolding. 15 Transportation of damaged roof sheets and debris etc., generated from above items by engaging tractor trolley including cost of fuel, wages of driver and required manpower for loading, transporting upto a lead of 2.0KM, unloading and stacking, material in the place shown by engineer-in-charge etc., complete as directed. (Note : The size of tractor trolly shall not be less than 3.0mX1.9mX0.45m) payment shall be made for each trip. 16 Transportation of dismantled/ removed damaged fiber reinforced cement corrugated sheets, FRP sheets, gutters, ridges etc. generated including loading, transportation out of NFC and to be disposed off through a Municipal Solid Waste management agency/ establishment, Ramkey or M/s HMEP or any approved licensec agency and disposed off in safe manner as per CPCB norms and providing a certificate to this extent. 17 Supplying and fixing Butyl rubber waterproof self adhesive UV resistant flashing tape of 100mm width, of approved make on cracked/damaged roof sheets. Note: Rate will include cost of surface preperation as per manufacturers specification. Overlapping will not be paid. Leak testing to be done post installaiton of flashing tape on roof sheeting 18 Supplying and installation of EPDM retrofit pipe flashing of make Dektite or other approved equivalent around pipe of size 235 to 425 mm.suggested model: Dektite RFS4Note: Rate to include cost of surface preperation and fixtures or fittings required forinstallation of pipe flashing.Leak testing to be done post installaiton. 19 PIPING AND ROOF GUTTER WORKS : 20 Providing and fixing110 mm n.b. un-plasticised PVC rain water pipes (single socketed pipes) with necessary PVC clamps and wooden gutties of approved make conforming to IS: 13592 type ‘A’ with injection moulded fittings, jointing with approved synthetic adhesive or seal rings conforming to IS: 5382 to make junctions leakproof, embedding the pipe into the slab/ gutter, fixing it to wall with proper fittings, testing complete in line, level and plumb all as directed. (used for rain water downcomer pipes) 21 Providing water proofing treatment to the roof gutters with cold applied, Acrylic Elastomeric liquid membrane coating over one coat of crystallization coating system Pidilite /Fosroc/Cica in the following sequence:a) Cleaning the surfaces from dirt, dust and other contaminationsb) Identifying the areas of leakage by approved means.c) Pressure grouting the area of leakage with cement slurry admixed with expansive grouting additive Conbex 100 of M/s Armstrong or its approved equivalent at a minimum one grout point per 2 Sqm slab area.d) Exposing, cleaning and filling cracks observed in RCC slab with polymer modified mortar compound/PU sealant.e) Cutting V grooves along concrete and masonry junctions and filling the same with single part Polyurethane sealant,.f) Pre wetting the surface of slab and application of one coat of crystallization coating system Xypex / Roofex@ 0.25 lt. /Sqm.g) Applying two coats of high soild, cold applied, Acrylic Elastomeric liquid membrane coating as primer coat at 1:1 dilution@ 250 ml/sqm/coat and 1st coat at 20% dilution @450ml/sqm/coat.h) Laying Fiber mesh on the surface.i) Over the Fiber mesh, Application of two coats of high solid, cold applied, Acrylic Elastomeric liquid membrane coating at 20% dilution @ 450 ml/sq.m/coat,all as per approved manufacturer’s specifications and as directed by Engineer in Charge. 22 Cleaning the RCC/MSrain water Gutters of various sizes at all elevations above plinth level including conveying , lifting water to the required elevation, pouring in to rainwater down take pipes, poking and clearing the choke if any, collecting dry leaves, waste etc. which were accumulated over the gutters and conveying all the debris upto a lead of 100 metres placing in heaps at the places shown and as directed by Engineer-in-charge. 23 CONCRETE WORKS : 24 Plain Cement Concrete 1:3:6 using Portland PozzolanaCement conforming to IS 1489 Part-1 (M/s. ACC, Ultra Tech, Ambuja, Birla make) with crushed stone sand and graded stone aggregates of 20mm maximum size at all depths/heights below/above plinth level including consolidation, finishing smooth/broom finish as applicable, curing, etc.,but excluding Formwork, complete as specified and directed. 25 WIND DRIVEN TURBO VENTILATORS 26 Supplying and fixing of 24 inch SS 304 wind driven turbo ventilators of size (410mm X 735mm) with 40 to 42 no of vanes of 0.5mm thick rolled formed SS steel having double permanently lubricated and sealed bearing of heavy quality, to be mounted on UV treated FRP Base plate (more than 60 % light transmission) fixing with fiber reinforced cement corrugated Roof Sheeting With Suitable self tapping screw or with FRP Coating to make leak proof complete as directed by engineer-in charge. 27 DEMOLISHING WORKS 28 Removing the existing broken/cracked fiber reinforced cement corrugatedroofing Sheets, ridges, hips, vallys, gutters, FRP roofing sheets etc., including G.I. Bolts, Nuts, washers and bitumen washers etc. carefully including required scaffolding and stacking the materials at a lead of 1.0 km as directed by Engineer-in- charge. 29 Removing the damaged rainwater downtake pipes of all diameters from all heights, including clamps and stacking the pipes at notified area within a lead of 100m 30 Dismantling/breaking the existing plain cement concrete surfaces carefully in flooring, ramp etc. to the required size, using pneumatic cutters or any approved means including disposing of debris within a distance of 50 m etc., complete as specified and directed. 31 Dismantling very carefully the existing reinforced cement concrete at all depths and heights below and above plinth level using pneumatic cutters or any approved means including cutting the reinforcement and transporting bars to departmental stores disposing the debris within the lead of 50 m complete as specified and directed 32 Dismantling very carefully the existing Brick masonry in cement mortar with plastering on both sides very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacking of useful materials and disposing the unserviceable debris within the lead of 50m, etc., complete as specified and directed.

BRR : 9836025 Tender For Structural Strengthening And Renovation Of Wtp-I Grww.- 1 Removing corroded worn out portion of reinforcement (when the area of baris damaged by more than 25%) by cutting and replacing the same by a newplain round bar of requisite diameter by binding with required lap / weldingwith old bar, including cost of reinforcement, complete in all respectincluding removing unserviceable materials from site as per direction of theEngineer - in - charge. Note : Payment on weight (Kg.) of newreinforcement. 2 BUILDING WORKS ( C ) Brickworks,Concrete Works etc?36...Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).(When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof).(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.Notes:- For shuttering in shell roof, grid roof with vertical faces folded plate, arched roof the rate in 36 (a), 36 (b) & 37 (c ) of subhead B above to be increased by100 % . For grid roof with splayed faces, rate is to be increased by 150 % 3 BUILDING WORKS ( C ) Brickworks,Concrete Works etc?33..Ordinary Cement concrete (mix 1:2:4) with graded stone chips (6mm nominal size) excluding shuttering and reinforcement,if any, in gound floor as perrelevant IS codes. Pakur variety? 4 BUILDING WORKS (E) ROOFING, SHEET WALLING &WATERPROOF TREATMENT . C. REPAIR & REHABILITATIONFOR WATERPROOFING 1. Taking out old damaged tarfelt from the roof, parapet etc. preparing the roof surfaces by removing all spoils, blisters,moss etc. from the working site and disposal of the same beyond the compound and cleaning the site in all respect as per direction of Engineer-in-Charge. All floor 5 SECTION 1BUILDING WORKS (I) PLASTERING,POINTING ETC.B. MISCELLANEOUS ITEMS 1 Labour for Chipping of concrete surface before taking up Plastering work. 6 Cleaning the concrete surface by removing dirt and debris,marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed,cutting the concrete to regular shape,wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. 7 Applying 2coats of Non-Toxic Acrylic Polymer modified Paint having adhesive & waterproofing properties by mixing in proportion (1 liquid: 4 cementitious material) or as per manufacturers specification for water proofing layer in water tank etc. (No Departmental Cement is required) 8 SECTION 1. ------------BUILDING WORKS (I) PLASTERING, POINTING ETC. A. ORIGINAL WORKS 1.Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] i) With 1:6 cement mortar (b) 20 mm thick plaster(3rd Corrigenda & addenda dated 04.06.2018) 9 Extra rate for using waterproofing and plasticising [email protected]% by weight of cement(or at manufacturers specified rate) for concrete of various grades. 10 Epoxy Bonding of new concrete to old concrete 11 Patching of damaged concrete surface with polymer concrete (25 mm nominal thick) and curing compounds, initiator and promoter, available inpresent formulations, to be applied as per instructionsof manufacturer and as approved by the Engineer - 12 Providing and inserting nipples with approved fixing compound after drilling holes for grouting as per Technical specifications including subsequentcutting/removal and sealing of the hole as necessary of nipples after completion of grouting withCement/Epoxy - 13 Sealing of cracks / porous concrete by injection process through nipples/Grouting complete as perTechnical specification.- Cement grouting - 14 Sealing of cracks / porous concrete by injection process through nipples/Grouting complete as perTechnical specification.Cement mortar (1:1) Grouting - 15 BUILDING WORKS (E) ROOFING, SHEET WALLING &WATERPROOF TREATMENT . C. REPAIR & REHABILITATIONFOR WATERPROOFING 2. Preparation of drainage spout on roof for bituminous waterproofing treatment after required grading and shaping of the under bed with Cement Concrete (1:2:4) or Cement Mortar (1:4) as directed, Chamfering and moulding the parapet wall to form a bell mouth entry, if required and providing full course treatment with bituminous felt to facilitate quick and smooth drainage of watwr into the down pipes complete including cost of all materials and labour according to satisfaction of the Engineer - in - Charge. (This item shall be done for reparing works only and shall not be used when original/renewal of tarfelting work is proposed to be undertaken) All floor 16 BUILDING WORKS (E) ROOFING, SHEET WALLING &WATERPROOF TREATMENT . D. REPAIR & REHABILITATION 1.Renewing rounding only (100 mm. radius) at the junction of roof and parapet etc. with beaten lime concrete (2:2:7) with slaked lime (2 lime putty / paste : 2 surki : 7 brick khoa ) 17 BUILDING WORKS (E) ROOFING, SHEET WALLING &WATERPROOF TREATMENT . C. REPAIR & REHABILITATIONFOR WATERPROOFING 3. Application of priming coat for standard bituminous waterproofing treatment over flat roof with Bitumen primer of approved brand fufilling the provision of I.S. 1346 - 1991 & 3384 - 1986 applied @ 0.27 Liters /Sq.m. over clean and prepared roof surface complete as per satisfaction of the Engineer - in - Charge. All Floor - (This item shall not be applied over C.I. or Asbestos roof) 18 BUILDING WORKS (E) ROOFING, SHEET WALLING &WATERPROOF TREATMENT . B. WATERPROOF TREATMENT4. Supplying & laying 3mm thick pre-fabricated plastomeric water proofing membrane conforming to EN 12311-1 & ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforced with non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusible polyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturers specification onsmooth,clean dry surface prepared wherever required.Lap joint shall be provided of 75 mm in longitudinal & 100 mm in transverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, complete removal of entrapped air and sealing edges into grooves in appropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicable taxes. (Payment shall be made on the basis of finished surface area.). Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) 19 SECTION 1BUILDING WORKS (J)WHITE WASH,COLOUR WASH, DISTEMPER B. MISCELLANEOUS ITEMS 4Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of theEngineer-in-charge). 20 SECTION 1BUILDING WORKS (J)WHITE WASH,COLOUR WASH, DISTEMPER A. ORIGINAL WORKS 8 ApplyingExterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. In Ground Floor:(a) One Coat [This item to be done under specific instruction of the Superintending Engineer]N.B.:-Extra for each additional floor in external walls refer item 1 of subhead C 21 Rendering the Surface of walls and ceiling with White Cement base WATER PROOF wall putty of approved make & brand.(1.5 mm thick) 22 SECTION 1BUILDING WORKS (J)WHITE WASH,COLOUR WASH, DISTEMPER A. ORIGINAL WORKS 7 ApplyingInterior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturers specification and as per direction of the EIC. (In Ground Floor) (a) One Coat ii) Solvent based interior grade Acrylic Primer.[This item to be done under specific instruction of the Superintending Engineer] 23 SECTION 1BUILDING WORKS (J)WHITE WASH,COLOUR WASH, DISTEMPER A. ORIGINAL WORKS 17 Protectiveand Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturers specification and as per direction ofEngineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. In Ground floor (Two Coat)a) Normal Acrylic Emulsion N.B. The items [17 (b) & 17(c)] of subhead A are to be selected only with written permission of Superintending Engineer for very resticted and small areas of a building. 24 CHAPTER - VII MISCELLANEOUS ITEMS Coating of Epoxy Resin of thickness not less than 160 micron with a lowviscosity,crystallization-resistant epoxy resin base with a reactive diluents combined with high build epoxy amine adducts as per BS 5493 standard and a polyamide or amido polyamine or any other suitable hardener. It shall react with epoxy resin at normal ambient temperature, suitable for solvent-free coatings as per recommended proportion for use on metal,concrete and wood surface to protect from corrosion as well as damagefrom chemical reaction after making the surface free from dust, oil and moisture etc. all complete as per instruction and to the satisfaction of ElC. [This item will be operatedon prior permission from the concerned SE/Dy Chief Engineer] 25 BUILDING WORKS (K) PAINTING, VERNISHING ETC?(A)ORIGINAL WORKS.(3)(B)Painting with superior quality aluminium paint of approved make and brand including smoothening surface by sand papering etc. on steel surface : (b) Two coats 26 BUILDING WORKS (K) PAINTING, VERNISHING ETC?(A)ORIGINAL WORKS.(4)Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats)ii) Luxury Quality 27 BUILDING WORKS (D) Flooring A. ORIGINAL WORKS 35.Supplying, fitting & fixing 1st quality Ceramic tiles in walls and floors to match with the existing work & 4 nos. of key stones (10mm) fixed with araldite at the back of each tile & finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by synthetic adhesive & grout materials etc. (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m. (a) Area of each tile upto 0.09 Sq.m (i) Coloured decorative Note: 2. Add extra for each addl, floor over the rate for item 35 & 36 of subhead A.(i) upto 4 th floor-Rs 5/ Sq.m (i) above 4 th floor-Rs 6.25/ Sq.m (3rd Corrigenda & addenda dated 04.06.2018) 28 BUILDING WORKS. (U) - Additional Items : 2)Supplying and laying true to line and level High Grip, Scratch resistant, Neutral to UV rays, Full Body Vitrified Tiles conforming to IS:15622-2006 & IS 4457-2007 and tested in accordance with IS:13630 [Non- modular sizes for tiles with Skid resistance: 0.6, Mohrs hardness > 7.0, Staining resistance: Class- 1, Water Absorption E < 0.5%] & MOR > 35N/sq.mm and Breaking strength > 1500 N for Outdoor area of building e. g.Gang-way, Corridor, Driveway, Parking lots, Courtyards, Slopingramps, Entrance lobbies, Patios, Portico etc. set over necessary underlay and 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg./Sqm, joints grouted with admixture of white cement and colouring pigment to match with colour of tiles and removal of wax coating of top surface of tiles with warm water and cleaning the tiles using soft and dry cloth complete including the cost of materials, labour and all other incidental charges complete including backside slurry but excluding the cost of underlay and true to the manufacturers specification and direction of Engineer-in- Charge. In Ground Floor: Sizes-300 mm x 300 mm x10 mm 29 BUILDING WORKS (D) Flooring B. REPAIR AND REHABILITATION6. Washing and cleaning with oxalic acid powder using 33 gms./sq.m. (b) Floor/ dado other than marble 30 Sub Total 31 GST 18% 32 CESS 1%

BRR : 11417770 Doing Civil Related Works In Akurdi Areas At Ward No.14 (For The Year 2025-26)-Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for thefoundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete. Removing and Transporting excavated / demolished material within PCMC limit including loading, unloading, stacking the material as directed by Engineer-in-charge etc. complete. (For Lead 10.0 Km). Providing and laying in situ cement concrete of 1:4:8 proportion with trap/ granite/ quartzite/ gneiss metal in foun dation including necessary form work, compacting and curing etc. complete. (with reversible drum type mixer with SCADA with fine agreegates of required specifications (VSI sand finely washed etc ) Providing and laying in situ cement concrete of 1:2:4 proportion with trap/ granite/ quartzite/ gneiss metal in foun dation including necessary form work, compacting and curing etc. complete. (with reversible drum type mixer with SCADA with fine agreegates of required specifications (VSI sand finely washed etc ) Providing and laying in situ Ready Mix cement concrete M-20 of trap / granite quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering formwork, laying/pumping cover blocks, compaction and curing roughening the surface special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate Crushed sand VSI Grade) Providing fly ash brick masonry with conventional / S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. Providing fly ash brick masonry with conventional/ S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete Lift 0.0 to 3.8 M Providing leak proof treatment by Injection grouting method to old floor without removing tiles of W.C., bath, with cement sand proportion of 1:1.5 and waterproofing compound at 2 Kilogram/bag of cement mixed in 35 liters of water including drilling holes in required position grouting with above mixed solution and ceiling etc. complete. Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete. Gound Floor Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete. Granular Sub Base Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material (Note- As per circular issued by Hon. city engineer PCMC , vide civil/CE/TS/23/16/2023.Date 21/04/2023 .Rate is reducedby 20% as material is brought from PCMCs C and waste processing plant.) Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material Removing the tar or coba and disposing of the material as directed etc. complete. Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Metre /Kilogram with two coat using approved chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete. Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. Ground Floor Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1Kilogramper cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Ground Floor Lift 0.0 to 3.8 M Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete. Ground floor Removing the existing cement plaster of any thickness without causing dust nuisance and stacking the debris upto a distance of 50 metres or spreading in the compound and cleaning the site etc. complete. Ground Floor Providing and laying ceramic tiles having size 30 cm. x 45 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. Providing and fixing 1.5 mm thick polyvenyl venyl chloride flooring including leveling the base with white cement including pasting with appropriate material cleaning the surface etc. complete Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in requiredposition laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Ground Floor Providing and laying vitrified mirror / glossy finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of to 10 mm thickness and confirming to IS. 15622-2006 group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete Ground Floor Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete. Ground Floor Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete. Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish , scaffolding if required etc. complete. Note:The work to be executed on prior approval Superintending Engineer will be necessary. Providing and laying in situ cement concrete M20 with tremix treatment for 100 mm thickness for flooring with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen etc. complete. Providing and laying chequered tiles of approved quality of size 30 cm x 30 cm, confirming to corresponding S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. Providing and applying two coats (exterior quality) of flat oil paint of approved colour and shade to the plastered surface in buildings and workshops including scaffolding if necessary, cleaning the surface and preparing surface etc. complete. (excluding primer coat) Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete. Ground Floor Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Ground Floor Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete. Ground Floor Providing and applying external raincoat painting with crack filling acrylic polymer based chemical compound coating to the external surface of walls to prevent water seepage in the masonry walls during monsoon added with required shade Steiner to give required shade to the surface in two coats. Including providing three coat of priming of polymer base primer including preparing surface scrapping the existing loose old paint, removing loose particles of sand on the surface opening and cleaning the cracksdeveloped in the external plaster, removing loose particles by chiseling, filling cracks by chemicals compound of approved make with proper penetration etc. Coating of Raincoat with the help of brush and as per instructions and specification given by manufacturer and with instruction from Engineer in- charge. Work shall be executed by certified applicator only and covering gurantee of 3 years on court stamp paper of Rs. 500/- and necessary testing etc. complete. Providing and applying washable oil-bound distemper of approved colour and shade to old and new surfaces in two coats including scaffolding, preparing the surfaces. (excluding the primer coat.) etc. complete. Lift 0.0 to 3.8 M Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not lessthan 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (With mechanical gear) Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossingswith hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983). Providing and fixing fiber glass reinforced polyster door shutter 30 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/ One Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. Providing and fixing steel window of various sizes as per detailed drawing without hot dip zinc coating, without ventilators, including fabricating / glazing with plain obscured glass panels of approved type and quality, iron oxidised fixtures and fastenings, oil painting two coats complete. Providing and fixing mild steel grill railing 20 Kilogram/sq.m with teak wood hand rail of size 75mm x 60 mm.and sill of 75mm.x 25 mm.and newel posts for staircases, including fabricating, fix-tures, erecting, painting the grill work with one coat of anti- corrosive paint and two coats of oil painting with approved colour and polishing the sill, hand rail and the newel post with french polish. Providing and fixing 40mm diameter and 1.5 mm thick Stainless steel hand railing in S.S.304 Grade including etc

BRR : 11109202 Tender For Yearly Civil Maintenance Work At Various Comm Complex And Etc For Pmpml-2 Excavation for foundation in earth, soil of all types, sand, gravel Cu.M and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m.) By Manual Means 3 Excavation for foundation in hard murum and boulders (Lift upto 1.5m.) Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5m.) 4 Excavation for foundation in Soft rock and old cement or lime Cu.M masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5m) By Mechanical Means 5 Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete 6 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to. 7 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.. 8 (Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats )Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats in main and cross beams, hip and jack rafters, purlins connecting to truss members and the like, as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/ bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete 9 ( Providing and fixing mild steel grill gate ) Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved colour and shade etc. complete.(weight 18 kg. to 20 kg. Per Sq.m.) Spec.No.: As directed by Engineer- in-charge. 10 ( PCC M20 for for bed blocks ) Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand 11 Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks,laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structuralsteel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) 12 ( Providing second class Burnt Brick masonry in plinth ) Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in plinth as backing in composite masonry including bailing out water manually, striking joints, raking out joints and watering etc Complete. 13 ( Providing second class Burnt Brick masonry in superstructure ) Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete 14 ( Providing second class Burnt Brick masonry half brick thick wall )Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete. 15 ( Providing fly ash brick masonry in foundation and plinth ) Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. 16 ( Providing fly ash brick masonry in superstructure ) Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete 17 Damp proof course 50 mm thick in M20 cement concrete : Providing and laying damp proof course 50 mm thick in M20 cement concrete layer and bitumen / using cement with waterproofing compound curing, formwork etc. complete 18 Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. 19 Providing waterproof plaster in W.C. and bath 12 mm thick for dado : Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) 20 Providing and applying water proofing treatment using acrylic polymer : Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sqm /kg with two coat using Dr. Fixit or alike of chemicals for masonry and concrete surface by brush covering 7 years guarantee on StampPapers etc. complete. 21 internal cement plaster 20mm thick : Providing internal cement plaster 20mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete. 22 Rough cast cement plaster externally in two coats : Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete. 23 Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete. 24 Polished Tandur Stone flooring 25mm to 30mm thick in plain/ diamond pattern: Providing and laying Polished Tandur Stone flooring 25mm to 30mm thick required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete. 25 polished Kadappa stone 25mm to 30mm thick ( sill ) , : Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of 1:4 cement mortar including cement float, filling joints with slurry, curing polishing and cleaning 26 ceramic tiles of having size 30 cm x 30 cm : Providing and laying ceramic tiles of having size 30 cm x 30 cm confirming to I.S.15622/2006 (group D II-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. 27 ceramic tiles of having size 30 cm. x 30 cm. : Providing and laying ceramic tiles of having size 30 cm. x 30 cm.and confirming to corresponding I.S. for dado and skirting inrequired position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete. 28 vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness a) Flooring : Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 ( group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Flooring 29 Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. 30 two coats of flat oil paint of approved colour to the old structural steel work : Providing and applying two coats of flat oil paint of approved colour to the old structural steel work and iron work previously painted in building including scaffolding, if necessary, cleaning and preparing the surface (excluding primer coat) etc. 31 Providing and applying two coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete. 32 Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. (on already painted surface) 33 two coats of exterior weather shield paint : Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat ,scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item No. 15 to 18 prior approval of Superintending 34 White-wash in two coats on old / new plastered : Providing and applying white-wash in two coats on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete. 35 Plastic emulsion paint to old surfaces in three coat : Providing and applying plastic emulsion paint of approved quality, colour and shade to old surface in three coats including scaffolding,preparing the surface. (excluding primer coat). 36 Providing and applying water bound distemper along with primer coats. Recommended companies: Asian, neroleck, Dulex 37 Corrugated galvanised iron sheets of 0.63mm thick (24 B.W.G.) : Providing and fixing corrugated galvanised iron sheets of 0.63mmthick (24 B.W.G.) for roofing without wind tiles including fastening with galvanised iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 kg/sq.m.). 38 6.00 mm thick ISI mark Asbestos Cement Corrugated sheet roofing : Providing and fixing 6.00 mm thick ISI mark Asbestos Cement Corrugated sheet roofing including galvanisediron J or L hook bolts galvanised iron band bituminous G.I. washers, galvanised iron clamps, bolts, nuts and scaffolding etc. 39 valley gutter of 22 B.W.G. (0.8 mm) plain galvanised iron sheets 120 cm wide : Providing and fixing valley gutter of 22 B.W.G. (0.8 mm) plain galvanised iron sheets 120 cm wide with teak wood planking 20 mm thick including two coats of coal-tarring the upper surface of plank etc. complete. (excluding painting to underside of plank). 40 Removing G.I. or A.C. sheet roofing : Removing G.I. or A.C. sheet roofing including purlins, principal rafters etc. including sorting serviceable and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etc. complete. 41 colour coated Zincalume profiled sheets for roofing : Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective 42 Solid core flush door shutter commercial in single leaf 32 mm : Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete. 43 Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S.62481979) (Without mechanical gear) 44 Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983). 45 Alluminium sliding windows two tracks d) with powder coating without box : Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension ?63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With powder coating without box 46 Acrylic plastic sheet panels to doors/windows (a) 2.00 mm thick : Providing and fixing acrylic plastic sheet panels of approved quality in required thickness plain clear or any colour or obscured linings in lieu of glass pans to doors/windows including providing and fixing clips, putty etc. complete. (a) 2.00 mm thick. 47 Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. 48 Partition of CCTW frame and commercial ply : Providing and fixing partitions made up of CCTW frame of size 75 mm x 50 mm at 60 cm c/c with 9 mm thick commercial ply and 4mm thick veneer on both sides with French polish etc. complete. 49 Aluminium partition partly glazed and partly laminated : Providng and fixing in position anodised extruded aluminum partitions, partly glazed and partly laminated having frame made out of extruded tubular section of size 40 mm x 60 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 128231990,laminated on both sides,Novateakor equivalent and 5 mm thick selected quality plain/ float glass panels fixed with aluminum glass clips 12 mm x 12 mm and rubber cushioning beading to glass partitions as per approved drawing etc. 50 push cock (Self closing tap) symet type of 15 mm dia. : Providing and fixing push cock (Self closing tap) symet type of 15 mm dia. including necessary socket, testing etc. complete 51 White Glazed Earthenware full stall type Urinal with P.V.C. flushing : Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall 52 white glazed earthenware Wash Hand Basin of 55cm. x 40 cm.size : Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete. 53 Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. 54 15cm x 10cm salt glazed stoneware gully trap : Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. 55 concrete pipes of I.S.NP. class of 300mm diameter : Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. 56 Brick Masonry Inspection Chamber 90cm x 45cm x 90cm : Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete. 57 Orissa type white glazed earthenware 575 mm water closet pan : Providing and fixing Orissa type white glazed earthenware 575 mm water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete. 58 H.D.P container Syntex or alike one piece moulded water tank : Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters 59 H.D.P container Syntex or alike one piece moulded water tank : Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres. 60 P.V.C. Rain water pipes of 110mm outer diameter : Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes,inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment) 61 Providing and laying in walls/ceilings/floors 15 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 1.25 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 62 Providing and laying in walls/ceilings/floors 25 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 63 Providing and laying in walls/ ceilings/floors 40 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 3.68 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 64 Providing and laying in walls/ceilings/floors 50 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 5.17 kg/metre necessary fitting remaking good the demolished portionwith filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. 65 Dismantling brick masonry in lime or cement mortar and stacking the materils as directed with all leads, lifts etc. 66 Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete. 67 Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete 68 Removing cement or lime plaster including disposing of the spoils as directed with all leads, lifts etc, complete. 69 Providing 1.5 mm thick pvc carpet of approved design n color &fixing at site as per site in charge instructions etc. completed. Note:- Dimensions would be considered as per actual carpet size fixed at site. 70 Transportation of material obtained from xcavation including soil, Cu.M rubble, bricks, RCC concrete, kerb stones, steel railing, iron pipes,channels etc. Obtained from dismantling, loading in a truck of minm.5 Cum.capacity or designed capacity and transporting within the municipal limits or anydesignatedplaceof corporation,unloading, stacking or spreading of material etc. complete.

BRR : 8169123 Yearly Civil Maintenance Work At Various Comm.Comlex And Etc For Pmpml - Excavation for foundation in earth, soil of all types, sand, gravel Cu.M and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m.) By Manual Means3 Excavation for foundation in hard murum and boulders (Lift upto 1.5m.) Excavation for foundation in hard murum and boulders including removing the excavated material up to a distance 50 meters, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5m.)4 Excavation for foundation in Soft rock and old cement or lime Cu.M masonry foundations including removing the excavated material upto a distance of 50 meters beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5m) By Mechanical Means5 Filling in plinth and floors with approved excavated material in 15cm. to 20cm. layers including watering and compacting etc. complete6 Filling in plinth and floors with contractors material/brought from outside and approved by Engineer in charge in layers of 15 cm to.7 Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete..8 (Providing and fabricating structural steel work in rolled sections, fixed with connecting plates or angle cleats) connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete9 ( Providing and fixing mild steel grill gate ) Providing and fixing mild steel grill gate as per the detailed drawing including hinges, locking arrangements and painting in three coats of oil paint of approved color and shade etc. complete.(Weight 18 kg. to 20 kg. Per Sq.m.) Spec.No.: As directed by Engineer-in-charge.10 ( PCC M20 for bed blocks ) Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. Quality Artificial Sand11 Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/granite/quartzite/gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows molded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks,laying/pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)12 ( Providing second class Burnt Brick masonry in plinth ) Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in plinth as backing in composite masonry including bailing out water manually, striking joints, raking out joints and watering etc Complete.13 ( Providing second class Burnt Brick masonry in superstructure ) Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete14 ( Providing second class Burnt Brick masonry half brick thick wall ) Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placed at every third course, proper ly bent and bonded at ends scaffolding, racking out joints and watering etc. complete.15 ( Providing fly ash brick masonry in foundation and plinth ) Providing fly ash brick masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete.16 ( Providing fly ash brick masonry in superstructure ) Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete17 Damp proof course 50 mm thick in M20 cement concrete : Providing and laying damp proof course 50 mm thick in M20 cement concrete layer and bitumen / using cement with waterproofing compound curing, formwork etc. complete18 Providing cement based water proofing treatment to terraces (Indian water proofing or similar) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mold at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc.19 Providing waterproof plaster in W.C. and bath 12 mm thick for dado : Providing waterproof plaster in W.C. and bath 12 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles)20 Providing and applying water proofing treatment using acrylic polymer : Providing and applying water proofing treatment using acrylic polymer modified cement based water proofing coating with fiber glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 sqm /kg with two coat using Dr. Fixit or similar of chemicals for masonry and concrete surface by brush covering 7 years guarantee on Stamp Papers etc. complete.21 internal cement plaster 20mm thick : Providing internal cement plaster 20mm thick in two coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.22 Rough cast cement plaster externally in two coats : Providing rough cast cement plaster externally in two coats to concrete, brick or stone masonry surfaces in all positions with base coat of 12 to 15 mm thick in C.M. 1:4 and rough cast treatment 12mm thick in proportion 1:1 1/2:3 including scaffolding and fourteen days curing complete.23 Providing neeru finish to plastered surfaces in all positions including scaffolding and curing etc. complete.24 Polished Tandur Stone flooring 25mm to 30mm thick in plain/ diamond pattern: Providing and laying Polished Tandur Stone flooring 25mm to 30mm thick required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.25 polished Kadappa stone 25mm to 30mm thick ( sill ), : Providing sills of polished Kadappa stone 25mm to 30mm thick, on a bed of 1:4 cement mortar including cement float, filling joints with slurry, curing polishing and cleaning26 ceramic tiles of having size 30 cm x 30 cm : Providing and laying ceramic tiles of having size 30 cm x 30 cm confirming to I.S.15622/2006 (group D II-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/color cement slurry cleaning curing etc.27 ceramic tiles of having size 30 cm. x 30 cm. : Providing and laying ceramic tiles of having size 30 cm. x 30 cm.and confirming to corresponding I.S. for dado and skirting unrequired position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ color cement slurry cleaning curing etc. complete.28 vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness a) Flooring : Providing and laying vitrified mirror / glossy finish tiles decorative type having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10 mm thickness and confirming to IS. 15622-2006 (group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and clearing etc. complete. Flooring29 Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm Providing and laying Antiskid Ceramic tiles of approved quality of size 30 cm x 30 cm and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.30 Two coats of flat oil paint of approved color to the old structural steel work : Providing and applying two coats of flat oil paint of approved color to the old structural steel work and iron work previously painted in building including scaffolding, if necessary, cleaning and preparing the surface (excluding primer coat) etc.31 Providing and applying two coats of flat oil paint of approved color and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.32 Providing and applying pearl/ luster finish paint of approved color and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. (on already painted surface)33 Two coats of exterior weather shield paint: Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved color to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete. NOTE: For Item No. 15 to 18 prior approval of Superintending34 White-wash in two coats on old / new plastered : Providing and applying white-wash in two coats on old / new plastered or masonry surfaces and asbestos cement sheets including scaffolding and preparing the surface by brushing and brooming down etc. complete.35 Plastic emulsion paint to old surfaces in three coats: Providing and applying plastic emulsion paint of approved quality, color and shade to old surfaces in three coats including scaffolding, preparing the surface. (excluding primer coat).36 Providing and applying water bound distemper along with primer coats. Recommended companies: Asian, Neroleck, Dulex37 Corrugated galvanized iron sheets of 0.63mm thick (24 B.W.G.) : Providing and fixing corrugated galvanized iron sheets of 0.63mmthick (24 B.W.G.) for roofing without wind tiles including fastening with galvanized iron screws and bolts, lead and bitumen washers as per drawing etc. complete.(Weight of 5.5 kg/sq.m.).38 6.00 mm thick ISI mark Asbestos Cement Corrugated sheet roofing : Providing and fixing 6.00 mm thick ISI mark Asbestos Cement Corrugated sheet roofing including galvanizediron J or L hook bolts galvanized iron band bituminous G.I. washers, galvanized iron clamps, bolts, nuts and scaffolding etc.39 valley gutter of 22 B.W.G. (0.8 mm) plain galvanized iron sheets 120 cm wide : Providing and fixing valley gutter of 22 B.W.G. (0.8 mm) plain galvanized iron sheets 120 cm wide with teak wood planking 20 mm thick including two coats of coal-tarring the upper surface of plank etc. complete. (excluding painting to underside of plank).40 Removing G.I. or A.C. sheet roofing : Removing G.I. or A.C. sheet roofing including purlins, principal rafters etc. including sorting serviceable and unserviceable materials, stacking the same as and where directed in the compound including scaffolding etc. complete.41 Color coated Zincalume profiled sheets for roofing : Providing and fixing color coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.5 mm TCT), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% aluminum 43.4% zinc 1.6% silicon) with COLORBOND (R) steel quality super durable polyester paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective42 Solid core flush door shutter commercial in single leaf 32 mm : Providing and fixing solid core flush door shutter commercial in single leaf 32 mm thick without ventilator commercial type of exterior grade as per detailed drawings with wrought iron hold fast, stainless steel fixtures and fastenings and handles on both sides and finishing with oil painting 3 coats complete.43 Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding boltts and handles for both sides, deep M.S. Channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S.62481979) (Without mechanical gear)44 Providing and fixing collapsible steel gate in one / two leaves with hot rolled vertical channels of 18 x 9 x 3 mm minimum size, crossings of M.S. flats of size 18 x 5 mm T or E section for runner of minimum 40 x 6 mm size for flange, M.S. flat for top runner of minimum size 40 x 12 mm with roller wheels confirming to grade F.G. 150 fitted with snap headed rivets of minimum size 6 mm max. spacing of vertical channels be 100 mm enclosed gate position and clear space of 150 mm between two sets of crossings with hold fasts, stoppers, spaces, handles, locking arrangement and one coat of red lead primer and oil painting etc. complete. (I.S. 105211983).45 Aluminum sliding windows two tracks d) with powder coating without box : Providing and fixing in position. (as per I.S.1868 / 1982) Aluminum sliding window of two tracks with rectangular pipe having overall dimension ?63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary aluminum sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With powder coating without box46 Acrylic plastic sheet panels to doors/windows (a) 2.00 mm thick : Providing and fixing acrylic plastic sheet panels of approved quality in required thickness plain clear or any color or obscured linings in lieu of glass pans to doors/windows including providing and fixing clips, putty etc. complete. (a) 2.00 mm thick.47 Providing and fixing in position powder coated aluminum louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminum frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.48 Partition of CCTW frame and commercial ply : Providing and fixing partitions made up of CCTW frame of size 75 mm x 50 mm at 60 cm c/c with 9 mm thick commercial ply and 4 mm thick veneer on both sides with French polish etc. complete.49 Aluminum partition partly glazed and partly laminated : Providing and fixing in position anodised extruded aluminum partitions, partly glazed and partly laminated having frame made out of extruded tubular section of size 40 mm x 60 mm with 12 mm thick three layered flat pressed teak wood particle board bonded with BWP type exterior grade phenol formaldehyde synthetic resin conforming to IS 128231990, laminated on both sides, Novateakor equivalent and 5 mm thick selected quality plain/ float glass panels fixed with aluminum glass clips 12 mm x 12 mm and rubber cushioning beading to glass partitions as per approved drawing etc.50 push cock (Self closing tap) symmetrical type of 15 mm dia. : Providing and fixing push cock (Self closing tap) symmetrical type of 15 mm dia. including necessary socket, testing etc. complete51 White Glazed Earthenware full stall type Urinal with P.V.C. flushing : Providing and fixing White Glazed Earthenware full stall type Urinal with P.V.C. Flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 mm dia. P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connection up to the outside face of the wall52 white glazed earthenware Wash Hand Basin of 55cm. x 40 cm.size : Providing and fixing white glazed earthenware Wash Hand Basin of 55cm. x 40 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connections including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.53 Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.54 15cm x 10cm salt glazed stonewareGully trap : Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.55 concrete pipes of I.S.NP. class of 300mm diameter : Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete.56 Brick Masonry Inspection Chamber 90cm x 45cm x 90cm : Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete with R.C.C. Cover medium duty 140 kg with frame etc complete.57 Orissa type white glazed earthenware 575 mm water closet pan : Providing and fixing Orissa type white glazed earthenware 575 mm water closet pan including S trap with earthenware foot rests, cast iron soil and vent pipe upto outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc. complete.58 H.D.P container Syntex or alike one piece molded water tank : Providing and fixing H.D.P container Syntex or alike one piece molded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters59 H.D.P container Syntex or alike one piece molded water tank : Providing and fixing H.D.P container Syntex or alike one piece molded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres.60 P.V.C. Rain water pipes of 110mm outer diameter : Providing and fixing P.V.C. Rain water pipes of 110mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, including fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 years for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment)61 Providing and laying in walls/ceilings/floors 15 mm dia. Medium grade having embossed as ISI Mark galvanized iron pipes of 1.25 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.62 Providing and laying in walls/ceilings/floors 25 mm dia. Medium grade having embossed as ISI Mark galvanized iron pipes of 2.49 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.63 Providing and laying in walls/ ceilings/ floors 40 mm dia. Medium grade having embossed as ISI Mark galvanized iron pipes of 3.68 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.64 Providing and laying in walls/ceilings/floors 50 mm dia. Medium grade having embossed as ISI Mark galvanized iron pipes of 5.17 kg/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.65 Dismantling brick masonry in lime or cement mortar and stacking the materials as directed with all leads, lifts etc.66 Removing rich mix cement concrete including stacking the spoils as directed with all leads, lifts etc, complete.67 Removing cement tiles, or marble or polished shahabad floor or dado without bed concrete including stacking the materials as directed with all leads, lifts etc. complete68 Removing cement or lime plaster including disposing of the spoils as directed with all leads, lifts etc, complete.69 Providing 1.5 mm thick pvc carpet of approved design n color & fixing at site as per site in charge instructions etc. completed. Note:- Dimensions would be considered as per actual carpet size fixed at site.70 Transportation of material obtained from excavation including soil, Cu.M rubble, bricks, RCC concrete, kerb stones, steel railing, iron pipes, channels etc. Obtained from dismantling, loading in a truck of min.5 Cum.capacity or designed capacity and transporting within the municipal limits or any designated place of corporation, unloading, stacking or spreading of material etc. complete.71 Cleaning of drainage line / rain line with manhole by Champion Mission - The following mentioned drainage line / rain gutter shall be cleaned completely up to the bottom of the manhole, channel and inlet with the manhole above: Cleaning by Champion Mission. This includes opening the manhole, closing it again, taking out the gravel, pumping water and sludge with a water pump as required, blocking it to one side as required, opening it, transporting the extracted material as per the instructions - arranging it etc. Pre-cleaning the area, taking stock of the area cleaned, controlling traffic, installing notice boards, lanterns, lamps etc., maintaining safety, taking all measures and precautions for the safety of workers, lighting etc. All materials - including labor, lead, light) (10% mirror test of the complete work after cleaning the drainage line / rain line is mandatory) 300 mm. Up to 600 mm. diameter line72 ft. manhole cleaning - cleaning and flushing of clogged manhole of any diameter and depth, cleaning of drainage line / rain line up to 2.00 meters on both sides of the manhole, transportation of goods - arranging transportation. This includes opening and closing the manhole, taking out the sand, pumping water and sludge with a pump, gluing, taking out the cleaned material, controlling traffic, installing notice boards, red lanterns, lamps etc., maintaining security, including lead lights and labor etc. All (10% mirror test is mandatory for cleaning of sanitary line / rain line cleaning) Cleaning of manholes on sanitary line73 Providing and Fixing in position, fabric based two part water proofing of kemperol/ Maris or equivalent make. Item to include, cleaning of surfcae, applying base coat, laying fleece with overlap and finishing coat and sprinkling sand over the coat while tacky. Item to include necessary scaffolding, cleaning, finishing etc complete