BRR : 9440734 Construction Of Phase-B Work At Jnv Balodabazar ( C.G ) - 1 EARTH WORK 2 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 3 All kinds of soil 4 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 5 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 6 Supplying chemical emulsion in sealed containers including delivery as specified. 7 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 8 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 9 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 10 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 11 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 12 CONCRETE WORK 13 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 14 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 15 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 16 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 17 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 18 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 19 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 20 REINFORCEDCEMENTCONCRETE 21 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 22 Foundations, footings, bases of columns, etc. for mass concrete 23 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 24 Columns, Pillars, Piers, Abutments, Posts and Struts 25 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 26 Edges of slabs and breaks in floors and walls 27 Under 20 cms wide 28 Suspended floors, roofs, landings, balconies and access platform. 29 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 30 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 31 50 mm thick 32 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 33 Thermo-Mechanically Treated bars of grade Fe-500D or more. 34 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 35 Thermo-Mechanically Treated bars of grade Fe-500 D or more. 36 Providing and fixing sheet covering over expansion joints with iron screws as per design. 37 Aluminium fluted strips 3.15 mm thick. 38 200 mm wide 39 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 40 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 41 All works upto plinth level 42 All works above plinth level upto floor V level 43 Add for using extra cement in the items of design mix over and above the specified cement content therein. 44 BRICK WORK 45 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 46 Cement mortar 1:6 (1 cement : 6 coarse sand) 47 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).: 48 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 49 Cement mortar 1:4 (1 cement :4 coarse sand) 50 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 51 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 52 MARBLE WORK 53 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 54 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble 55 Area of slab over 0.50 sqm 56 Granite of any colour and shade 57 Area of slab over 0.50 sqm 58 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 59 Marble work 60 Granite work 61 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 62 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 63 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. 64 Granite Stone of approved shade 65 WOOD WORK & PVC WORK 66 Float Glass Panes 67 4mm thick glass pane (weight not less than 10 kg/sqm 68 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 69 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 70 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws 71 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 72 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 73 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 74 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 75 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 76 35 mm thick shutters 77 Kiln seasoned and chemically treated hollock wood 78 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 79 Fixed to steel windows by welding 80 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 81 With 12 mm mild steel U beading 82 Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete : 83 150 mm 84 Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 85 90 mm 86 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 87 250 mm weighing not less than 150 gms 88 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 89 75 mm 90 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 91 250x16 mm 92 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 93 200x10 mm 94 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 95 Twin rubber stopper 96 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 97 50x50 mm (base and height) 98 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 99 1.5 mm thick 100 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 101 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 102 STEEL WORK 103 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 104 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 105 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 106 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 107 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 108 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 109 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 110 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 111 M.S. tube 112 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 113 4.0 mm thick glass panes 114 FLOORING 115 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). 116 (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 117 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 118 18 mm thick 119 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 120 40 mm wide and 4 mm thick 121 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 122 25 mm thick. 123 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 124 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 125 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. 126 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 127 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 128 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 129 Size of Tile 600x600 mm 130 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. 131 Size of Tile 600x600 mm 132 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 133 ROOFING 134 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 12.19.1 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 135 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 136 FINISHING 137 12 mm cement plaster of mix 138 1:6 (1 cement: 6 coarse sand) 139 15 mm cement plaster on rough side of single or half brick wall of mix: 140 1:6 (1 cement: 6 coarse sand) 141 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 142 20 mm Cement Plaster 143 6mm cement plaster of mix 144 1:3 (1 cement : 3 fine sand) 145 White washing with lime to give an even shade : 146 New work (three or more coats) 147 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 148 New work (two or more coats) over and including water thinnable priming coat with cement primer 149 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 150 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 151 Applying priming coat: 152 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 153 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 154 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 155 Two or more coats on new work 156 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 157 Two or more coats on new work 158 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 159 WATER PROOFING 160 Providing and laying water proofing treatment to vertical andhorizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 161 Ist course of applying cement slurry @ 4.4 kg/sqm mixedwith water proofing compound conforming to IS 2645 inrecommended proportions including rounding off junction ofvertical and horizontal surface. 162 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 163 IIIrd course of applying blown or residual bitumen applied hotat 1.7 kg. per sqm of area. 164 IVth course of 400 micron thick PVC sheet. (Overlaps at jointsof PVC sheet should be 100 mm wide and pasted to eachother with bitumen @ 1.7 kg/sqm). 165 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 166 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 167 Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. 168 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 169 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 170 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). 171 NON SHEDULE ITEMS 172 Providing and laying cinder filling in sunken floors and other locationswith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawings and as directed by the Engineer in Charge. 173 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 174 150 mm 175 Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in-Charge : 176 Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc complete in all respects as per specifications/drawings and to the entire satisfaction to the Architect. 177 (SANITARY WORKS) GIRLS DORMITORY WITH 3 NO WARDEN RESIDENCE 178 EARTH WORK 179 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 180 All kinds of soil. 181 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 182 All kinds of soil 183 Pipes, cables etc, not exceeding 80 mm dia. 184 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 185 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 186 ROOFING 187 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 188 110 mm diameter 189 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 190 Coupler 191 110 mm 192 Bend 87.5° 193 110 mm bend 194 Shoe (Plain) 195 110 mm Shoe 196 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 197 110 mm 198 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 199 SANITARY INSTALLATIONS 200 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 201 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 202 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 203 W.C. pan with ISI marked black solid plastic seat and lid 204 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively. 205 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 206 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 207 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 208 Kitchen sink with drain board 209 510x1040 mm bowl depth 250 mm 210 Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. 211 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 212 Providing and fixing toilet paper holder : 213 Vitreous china 214 Providing and fixing soil, waste and vent pipes : 215 100 mm dia. 216 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 217 75mm diameter 218 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 219 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 220 For 100 mm dia. pipe 221 For 75 mm dia. pipe 222 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 223 100 mm 224 Sand cast iron S&S as per IS - 3989 225 75 mm 226 Sand cast iron S&S as per IS- 3989 227 Providing and fixing plain bend of required degree. 228 100 mm 229 Sand cast iron S&S as per IS : 3989 230 75 mm 231 Sand cast iron S&S as per IS - 3989 232 Providing and fixing heel rest sanitary bend 233 100 mmdia 234 Sand cast iron S&S as per IS - 3989 235 75 mm dia 236 Sand cast iron S&S as per IS - 3989 237 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick,bolts and nuts complete. 238 100x100x100mm 239 Sand cast iron S&S as per IS - 3989 240 75x75x75mm 241 Sand cast iron S&S as per IS - 3989 242 Providing and fixing single equal plain junction of required degree 243 100x100x100mm 244 Sand cast iron S&S as per IS - 3989 245 75x75x75mm 246 Sand cast iron S&S as per IS - 3989 247 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 248 100 mm 249 Sand cast iron S&S as per IS - 3989 250 75 mm 251 Sand cast iron S&S as per IS - 3989 252 Providing and fixing terminal guard : 253 100 mm 254 Sand cast iron S&S as per IS - 3989 255 75 mm 256 Sand cast iron S&S as per IS - 3989 257 Providing and fixing collar : 258 100 mm 259 Sand cast iron S&S as per IS - 3989 260 75 mm 261 Sand cast iron S&S as per IS - 3989 262 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 263 100 mm 264 75 mm 265 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 266 100 mm 267 75 mm 268 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 269 100 mm inlet and 100 mm outlet 270 Sand Cast Iron S&S as per IS: 1729 271 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 272 100 mm dia 273 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 274 100 mm diameter pipe 275 75 mm diameter pipe 276 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 277 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 278 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 279 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 280 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 281 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 282 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 283 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 284 Kitchen sink with drain board 285 510x1040 mm bowl depth 250 mm 286 Providing and fixing 8mm dia C.P / S.S Jet with flexible tube upto1 metre long with S.S triangular plate to Eureopean type W.C of quality and make as approved by engineer-in-charge. 287 Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling. 288 External work 289 32mmdia nominal bore 290 40mmdia nominal bore 291 50mmdia nominal bore 292 WATER SUPPLY 293 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 294 Internal work - Exposed on wall 295 20 mm nominal outer dia Pipes 296 25 mm nominal outer dia Pipes 297 32 mm nominal outer dia Pipes 298 40 mm nominal outer dia Pipes 299 50 mm nominal outer dia Pipes 300 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 301 Concealed work, including cutting chases and making good the walls etc. 302 15 mm nominal outer dia Pipes 303 20 mm nominal outer dia Pipes 304 25 mm nominal outer dia Pipes 305 32 mm nominal outer dia Pipes 306 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 307 25 to 40 mm nominal bore 308 Providing and fixing brass stop cock of approved quality : 309 15 mm nominal bore 310 20 mm nominal bore 311 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 312 25mm nominal bore 313 32mm nominal bore 314 40mm nominal bore 315 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 316 25 mm nominal bore 317 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 318 25 mm nominal bore 319 Providing and fixing uplasticised PVC connection pipe with brass unions : 320 45 cm length 321 15 mm nominal bore 322 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 323 100 mm diameter 324 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 325 Rectangular tank 326 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 327 15 mm nominal bore 328 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 329 15 mm nominal bore 330 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 331 15 mm nominal bore. 332 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 333 15 mm nominal bore 334 Providing and fixing PTMT grating of approved quality and colour. 335 Circular type. 336 100 mm nominal dia. 337 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 338 SEWARAGE & DRAINAGE 339 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 340 100 mm diameter 341 150 mm diameter 342 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 343 100 mm diameter S.W. pipe 344 150 mm diameter S.W. pipe 345 250 mm diameter S.W. pipe 346 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 347 180 x 150 mm size P type 348 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 349 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 350 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 351 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 352 Extra for depth for manholes : 353 Size 90x80 cm 354 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 355 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 356 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 357 For pipes 100 to 250 mm diameter 358 Providing, laying and jointing non pressure NP2 class (light duty)RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 359 150 mm dia RCC pipe 360 250 mm dia RCC pipe 361 NON SHEDULE ITEMS 362 Providing and fixing C.P. brass floor clean out plug of approved make complete in all respect. 100 mm dia. 363 Providing and fixing floor drain points of 75 x 50mmreducer bend with 100 mm dia CP grating with frame, embedded in floor including making joints with waste pipe etc. complete in all respects as per drawing and as directed by theEngineer in Charge. 364 Providing and fixing concealed single leverbath & overhead shower mixer of hindware make and model No.(F360019CP) respectively or equivalent approved make as approved byEngineer in charge. 365 Supplying, fixing, testing and commissioning of storage type water heater (Geyser) etc. with Stainless steel body , copper container , automatic thermostatic control electric element, pressure release valve, M.S. nuts and bolts etc. conforming to IS: 2082 366 25 Litre Capacity 367 Providing & fixing Sink Mixer with Swinging Casted Spout (Wall Mounted Jaquar model CON-309 KN)/approved equal with 450mm long copper pipes & brass nuts. 368 Providing and fixing C.P. brass grab bar(600mm long) fixed with C.P. brass screwsincluding all fittings complete.Jaquar model no. AHS-1507/approve equal. 369 Providing and fixing C.P. brass push type pillar cock for wash basinof approved quality.Jaquar model no. PRS-031/approved equal make. 370 Providing and fixing C.P. brass push type auto closing urinal valve with built in control cock & wall flangeof approved quality.Jaquar model no. PRS-031/approved equal make. 371 Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipesfor rain water Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),reducers, couplers, cowls, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. 372 The Pipes will be supported with threaded G I rods & clamps on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 373 160 mm outer dia 374 GIRLS DORMITORY WITH 3 NO WARDEN RESIDENCE (ELECTRICAL WORKS) 375 SUBHEAD - I - WIRING 376 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 377 Group C 378 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 379 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 380 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 381 4 Module (125 mmX75 mm) 382 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 383 15/16 A switch 384 3 pin 5/6 A socket outlet 385 Telephone socket outlet 386 TV antenna socket outlet 387 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 388 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 389 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 390 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 391 4 X 4 sq. mm + 2 X 4 sq. mm earth wire 392 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 393 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 394 25 mm 395 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 396 1 or 2 Module (75 mmX75 mm) 397 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 398 2 Pair 399 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 400 20 mm 401 25 mm 402 Providing and fixing in position 2mm thick M.S. Telephone junction box of size suitable for fixing of following Krone Tag Block with key lock arrangement. Also provide clamps for fixing tag blocks. 403 10 pair Telephone Tag Blockwith box 404 Supplying, laying of 10 pair unarmoured PVC insulated copper conductor (ATC) telephone cable in ground/existing pipes/on wall and making connection with telephone main junction box (MDF) including supports and all accessories as required 405 10 Pair Cable unarmoured 406 SUBHEAD - II - SUPPLY & INSTALLATION OF FITTINGS 407 Supplying of following box type Fl. fitting made out of CRCA sheet finished in antirust treated non-yellowing super white stove enamelled paint duly wired with copper wound heavy duty choke starter holder, starter but without lamp complete etc. as reqd. 408 Mounting rail for TLED lamps 1600 Lumens (TMC 501 P 1xT-LED with Essential LED 18W Tube) 409 Sereno 42 watt 2950 lumens philips SP824 P LED 30S-5000 GR OA 410 Supplying of wall mounted suitable for 1300 Lumens complete with ballast & accessories such as wire guard etc. complete as required. 411 15W Astra Surface & wall mounted 1300 Lumens ( Philips BN150W LED13S-6500 PSE OD GR ) 412 Supplying of wall bracket light fittings suitable for 11 / 13 W CFL lamp. The fitting shall be made up of M.S. powder coated provided with integral ballast, frosted glass and 1 no. 11 / 13 Wlamp duly wired upto the connector block complete as required. (Decon Cat. No.05AAM) 413 Supplying of ceiling light fittings suitable for 1 x 15/20 W LED lamp. The fitting shall be made up of M.S. powder coated provided with electronic ballast, 1 no. 15/20 W LED lamp duly wired upto the connector block etc. complete as required. 414 Cirrus Mini Pro 15 / 20 watt & 1100 /1600 Lumens (Philips SM200C LED11S 6500 PSU OD WH) 415 Supplying of bulk head fittings suitable for 10 W LED lamp complete with ballast & accessories such as glass, wire guard, 60 W CFL lamp etc. complete as required. 416 Endural LED-Bulkhead, 10 W, 600 lumen Such as (Philips WT202W LED6S CW PSU S2 PC) 417 Supplying of exhaustfan, all complete with mounting ring frame i/c bracket,but without regulator with shutters in the following sizes. (G.E. ALSTHOM, KHAITAN & HAVELLS COMPANY) 418 300 mm 4 Pole 419 Supplying of 1400 mm sweep A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply. (CROMPTON, KHAITAN & HAVELLS COMPANY) 420 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 421 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 422 Installation, testing and commissioning of pre-wired, Light Fixture / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 423 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 424 Upto 450 mm sweep 425 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 426 Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. 427 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. 428 SUBHEAD - III - DISTRIBUTION BOARD 429 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 430 6 way (4 + 18), Double door 431 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 432 100 A 433 Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 434 63 A 435 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 436 40 amps 437 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 438 12 way , Double door 439 16 way , Double door 440 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 441 25 A 442 40 A 443 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 444 Single pole 445 SUBHEAD - IV - EARTHING 446 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 447 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. 448 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 449 SUBHEAD - V - STREET LIGHTING ON BUILDING 450 Supplying, installing, testing and commissioning of 2 x 36W general purpose flourescent street light fittings with sheet aluminium housing and UV stabilized acrylic cover complete with chokes, starter holders, condensers, reflector cover etc. as reqd. (Philips Cat No. TRC 33 / 236 HPF) (To be fixed directly on wall of building) 451 Supplying and fixing of 32 mm dia X 2.00 meter long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 Nos. 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required. 452 Supply of following sizes of FRLS 1.1 KV stranded compact circular aluminium conductor screened with extruded semi conducting compound, XLPE insulated,Al round wire armoured & overall PVC sheathed cableconforming to IS to IS 7098 (Part-I) with latest amendments 453 2 x 4 sq.mm 454 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 455 Upto 35 sq. mm 456 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 457 Upto 35 sq. mm 458 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. 459 Upto 35 sq. mm (clamped with 1mm thick saddle) 460 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 461 2 X 6 sq. mm (19mm) 462 Supply & fixing of 150x200 mm 60mm deep MS junction box recess or surface on wall with 3mm bakalite cover15 overlapping 15 all sides of junction Box & housing 4way 32amps bakelie connector to terminate incoming & outgoing armoured cable & & wiring the light fixture with 3x1.5 sq mm PVC insulated coppwer wire including interconnection ets as reqired .( Cost of termination of armoured cable with gland is not to be included as the same is payable under separate item no 5.07 of this SUBHEAD) 463 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing withcement mortar1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required. 464 100 mm dia 465 SUBHEAD - VI - LIGHTNING CONDUCTOR 466 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 467 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 468 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 469 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 470 Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chucknuts and spring washers etc. complete as required. 471 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrodedirectly in ground as required 472 (CIVIL WORK )BOYS DORMITORY WITH 3 NO WARDEN RESIDENCE 473 EARTH WORK 474 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 475 All kinds of soil 476 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 477 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 478 Supplying chemical emulsion in sealed containers including delivery as specified. 479 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 480 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 481 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 482 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 483 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 484 CONCRETE WORK 485 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 486 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 487 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 488 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 489 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 490 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 491 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 492 REINFORCEDCEMENTCONCRETE 493 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 494 Foundations, footings, bases of columns, etc. for mass concrete 495 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 496 Columns, Pillars, Piers, Abutments, Posts and Struts 497 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 498 Edges of slabs and breaks in floors and walls 499 Under 20 cms wide 500 Suspended floors, roofs, landings, balconies and access platform. 501 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 502 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 503 50 mm thick 504 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 505 Thermo-Mechanically Treated bars of grade Fe-500D or more. 506 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 507 Thermo-Mechanically Treated bars of grade Fe-500 D or more. 508 Providing and fixing sheet covering over expansion joints with iron screws as per design. 509 Aluminium fluted strips 3.15 mm thick. 510 200 mm wide 511 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 512 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 513 All works upto plinth level 514 All works above plinth level upto floor V level 515 Add for using extra cement in the items of design mix over and above the specified cement content therein. 516 BRICK WORK 517 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 518 Cement mortar 1:6 (1 cement : 6 coarse sand) 519 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).: 520 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 521 Cement mortar 1:4 (1 cement :4 coarse sand) 522 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 523 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 524 MARBLE WORK 525 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 526 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble 527 Area of slab over 0.50 sqm 528 Granite of any colour and shade 529 Area of slab over 0.50 sqm 530 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 531 Marble work 532 Granite work 533 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 534 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 535 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. 536 Granite Stone of approved shade 537 WOOD WORK & PVC WORK 538 Float Glass Panes 539 4mm thick glass pane (weight not less than 10 kg/sqm 540 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 541 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 542 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws 543 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 544 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 545 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 546 Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured). 547 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 548 35 mm thick shutters 549 Kiln seasoned and chemically treated hollock wood 550 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 551 Fixed to steel windows by welding 552 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 553 With 12 mm mild steel U beading 554 Providing and fixing ISI marked oxidised M.S. single acting spring hinges with necessary screws etc. complete : 555 150 mm 556 Providing and fixing oxidised M.S. hasp and staple (safety type) conforming to IS : 363 with necessary screws etc. complete : 557 90 mm 558 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 559 250 mm weighing not less than 150 gms 560 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 561 75 mm 562 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 563 250x16 mm 564 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 565 200x10 mm 566 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 567 Twin rubber stopper 568 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 569 50x50 mm (base and height) 570 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 571 1.5 mm thick 572 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 573 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 574 STEEL WORK 575 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 576 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 577 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 578 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 579 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 580 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 581 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 582 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 583 M.S. tube 584 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 585 4.0 mm thick glass panes 586 FLOORING 587 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). 588 (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 589 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 590 18 mm thick 591 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 592 40 mm wide and 4 mm thick 593 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 594 25 mm thick. 595 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 596 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 597 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. 598 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 599 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 600 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 601 Size of Tile 600x600 mm 602 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. 603 Size of Tile 600x600 mm 604 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 605 ROOFING 606 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 12.19.1 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 607 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 608 FINISHING 609 12 mm cement plaster of mix 610 1:6 (1 cement: 6 coarse sand) 611 15 mm cement plaster on rough side of single or half brick wall of mix: 612 1:6 (1 cement: 6 coarse sand) 613 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 614 20 mm Cement Plaster 615 6mm cement plaster of mix 616 1:3 (1 cement : 3 fine sand) 617 White washing with lime to give an even shade : 618 New work (three or more coats) 619 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 620 New work (two or more coats) over and including water thinnable priming coat with cement primer 621 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: 622 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 623 Applying priming coat: 624 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 625 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 626 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 627 Two or more coats on new work 628 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 629 Two or more coats on new work 630 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 631 WATER PROOFING 632 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 633 Ist course of applying cement slurry @ 4.4 kg/sqm mixedwith water proofing compound conforming to IS 2645 inrecommended proportions including rounding off junction of vertical and horizontal surface. 634 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 635 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 636 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm). 637 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 638 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 639 Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. 640 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 641 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 642 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). 643 NON SHEDULE ITEMS 644 Providing and laying cinder filling in sunken floors and other locationswith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawings and as directed by the Engineer in Charge. 645 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 646 150 mm 647 Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in-Charge : 648 Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc complete in all respects as per specifications/drawings and to the entire satisfaction to the Architect. 649 (SANITARY WORKS) BOYS DORMITORY WITH 3 NO WARDEN RESIDENCE 650 EARTH WORK 651 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 652 All kinds of soil. 653 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 654 All kinds of soil 655 Pipes, cables etc, not exceeding 80 mm dia. 656 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 657 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 658 ROOFING 659 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 660 110 mm diameter 661 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 662 Coupler 663 110 mm 664 Bend 87.5° 665 110 mm bend 666 Shoe (Plain) 667 110 mm Shoe 668 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 669 110 mm 670 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 671 SANITARY INSTALLATIONS 672 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 673 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 674 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : 675 W.C. pan with ISI marked black solid plastic seat and lid 676 Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively. 677 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 678 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 679 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 680 Kitchen sink with drain board 681 510x1040 mm bowl depth 250 mm 682 Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. 683 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 684 Providing and fixing toilet paper holder : 685 Vitreous china 686 Providing and fixing soil, waste and vent pipes : 687 100 mm dia. 688 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 689 75mm diameter 690 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 691 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 692 For 100 mm dia. pipe 693 For 75 mm dia. pipe 694 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 695 100 mm 696 Sand cast iron S&S as per IS - 3989 697 75 mm 698 Sand cast iron S&S as per IS- 3989 699 Providing and fixing plain bend of required degree. 700 100 mm 701 Sand cast iron S&S as per IS : 3989 702 75 mm 703 Sand cast iron S&S as per IS - 3989 704 Providing and fixing heel rest sanitary bend 705 100 mmdia 706 Sand cast iron S&S as per IS - 3989 707 75 mm dia 708 Sand cast iron S&S as per IS - 3989 709 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick,bolts and nuts complete. 710 100x100x100mm 711 Sand cast iron S&S as per IS - 3989 712 75x75x75mm 713 Sand cast iron S&S as per IS - 3989 714 Providing and fixing single equal plain junction of required degree 715 100x100x100mm 716 Sand cast iron S&S as per IS - 3989 717 75x75x75mm 718 Sand cast iron S&S as per IS - 3989 719 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 720 100 mm 721 Sand cast iron S&S as per IS - 3989 722 75 mm 723 Sand cast iron S&S as per IS - 3989 724 Providing and fixing terminal guard : 725 100 mm 726 Sand cast iron S&S as per IS - 3989 727 75 mm 728 Sand cast iron S&S as per IS - 3989 729 Providing and fixing collar : 730 100 mm 731 Sand cast iron S&S as per IS - 3989 732 75 mm 733 Sand cast iron S&S as per IS - 3989 734 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 735 100 mm 736 75 mm 737 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 738 100 mm 739 75 mm 740 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 741 100 mm inlet and 100 mm outlet 742 Sand Cast Iron S&S as per IS: 1729 743 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 744 100 mm dia 745 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 746 100 mm diameter pipe 747 75 mm diameter pipe 748 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 749 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 750 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 751 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 752 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 753 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 754 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 755 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 756 Kitchen sink with drain board 757 510x1040 mm bowl depth 250 mm 758 Providing and fixing 8mm dia C.P / S.S Jet with flexible tube upto1 metre long with S.S triangular plate to Eureopean type W.C of quality and make as approved by engineer-in-charge. 759 Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling. 760 External work 761 32mmdia nominal bore 762 40mmdia nominal bore 763 50mmdia nominal bore 764 WATER SUPPLY 765 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 766 Internal work - Exposed on wall 767 20 mm nominal outer dia Pipes 768 25 mm nominal outer dia Pipes 769 32 mm nominal outer dia Pipes 770 40 mm nominal outer dia Pipes 771 50 mm nominal outer dia Pipes 772 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 773 Concealed work, including cutting chases and making good the walls etc. 774 15 mm nominal outer dia Pipes 775 20 mm nominal outer dia Pipes 776 25 mm nominal outer dia Pipes 777 32 mm nominal outer dia Pipes 778 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 779 25 to 40 mm nominal bore 780 Providing and fixing brass stop cock of approved quality : 781 15 mm nominal bore 782 20 mm nominal bore 783 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 784 25mm nominal bore 785 32mm nominal bore 786 40mm nominal bore 787 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 788 25 mm nominal bore 789 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 790 25 mm nominal bore 791 Providing and fixing uplasticised PVC connection pipe with brass unions : 792 45 cm length 793 15 mm nominal bore 794 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 795 100 mm diameter 796 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 797 Rectangular tank 798 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 799 15 mm nominal bore 800 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 801 15 mm nominal bore 802 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 803 15 mm nominal bore. 804 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 805 15 mm nominal bore 806 Providing and fixing PTMT grating of approved quality and colour. 807 Circular type. 808 100 mm nominal dia. 809 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 810 SEWARAGE & DRAINAGE 811 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 812 100 mm diameter 813 150 mm diameter 814 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 815 100 mm diameter S.W. pipe 816 150 mm diameter S.W. pipe 817 250 mm diameter S.W. pipe 818 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 819 180 x 150 mm size P type 820 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 821 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 822 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 823 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 824 Extra for depth for manholes : 825 Size 90x80 cm 826 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 827 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 828 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 829 For pipes 100 to 250 mm diameter 830 Providing, laying and jointing non pressure NP2 class (light duty)RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 831 150 mm dia RCC pipe 832 250 mm dia RCC pipe 833 NON SHEDULE ITEMS 834 Providing and fixing C.P. brass floor clean out plug of approved make complete in all respect. 100 mm dia. 835 Providing and fixing floor drain points of 75 x 50mmreducer bend with 100 mm dia CP grating with frame, embedded in floor including making joints with waste pipe etc. complete in all respects as per drawing and as directed by theEngineer in Charge. 836 Providing and fixing concealed single leverbath & overhead shower mixer of hindware make and model No.(F360019CP) respectively or equivalent approved make as approved byEngineer in charge. 837 Supplying, fixing, testing and commissioning of storage type water heater (Geyser) etc. with Stainless steel body , copper container , automatic thermostatic control electric element, pressure release valve, M.S. nuts and bolts etc. conforming to IS: 2082 838 25 Litre Capacity 839 Providing & fixing Sink Mixer with Swinging Casted Spout (Wall Mounted Jaquar model CON-309 KN)/approved equal with 450mm long copper pipes & brass nuts. 840 Providing and fixing C.P. brass grab bar(600mm long) fixed with C.P. brass screwsincluding all fittings complete.Jaquar model no. AHS-1507/approve equal. 841 Providing and fixing C.P. brass push type pillar cock for wash basinof approved quality.Jaquar model no. PRS-031/approved equal make. 842 Providing and fixing C.P. brass push type auto closing urinal valve with built in control cock & wall flangeof approved quality.Jaquar model no. PRS-031/approved equal make. 843 Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipesfor rain water Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),reducers, couplers, cowls, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. 844 The Pipes will be supported with threaded G I rods & clamps on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 845 160 mm outer dia 846 (ELECTRICAL WORKS) BOYS DORMITORY WITH 3 NO WARDEN RESIDENCE 847 SUBHEAD - I - WIRING 848 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 849 Group C 850 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 851 Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 852 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 853 4 Module (125 mmX75 mm) 854 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 855 15/16 A switch 856 3 pin 5/6 A socket outlet 857 Telephone socket outlet 858 TV antenna socket outlet 859 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 860 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 861 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 862 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 863 4 X 4 sq. mm + 2 X 4 sq. mm earth wire 864 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 865 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 866 25 mm 867 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 868 1 or 2 Module (75 mmX75 mm) 869 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 870 2 Pair 871 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 872 20 mm 873 25 mm 874 Providing and fixing in position 2mm thick M.S. Telephone junction box of size suitable for fixing of following Krone Tag Block with key lock arrangement. Also provide clamps for fixing tag blocks. 875 10 pair Telephone Tag Blockwith box 876 Supplying, laying of 10 pair unarmoured PVC insulated copper conductor (ATC) telephone cable in ground/existing pipes/on wall and making connection with telephone main junction box (MDF) including supports and all accessories as required 877 10 Pair Cable unarmoured 878 SUBHEAD - II - SUPPLY & INSTALLATION OF FITTINGS 879 Supplying of following box type Fl. fitting made out of CRCA sheet finished in antirust treated non-yellowing super white stove enamelled paint duly wired with copper wound heavy duty choke starter holder, starter but without lamp complete etc. as reqd. 880 Mounting rail for TLED lamps 1600 Lumens (TMC 501 P 1xT-LED with Essential LED 18W Tube) 881 Sereno 42 watt 2950 lumens philips SP824 P LED 30S-5000 GR OA 882 Supplying of wall mounted suitable for 1300 Lumens complete with ballast & accessories such as wire guard etc. complete as required. 883 15W Astra Surface & wall mounted 1300 Lumens ( Philips BN150W LED13S-6500 PSE OD GR ) 884 Supplying of wall bracket light fittings suitable for 11 / 13 W CFL lamp. The fitting shall be made up of M.S. powder coated provided with integral ballast, frosted glass and 1 no. 11 / 13 Wlamp duly wired upto the connector block complete as required. (Decon Cat. No.05AAM) 885 Supplying of ceiling light fittings suitable for 1 x 15/20 W LED lamp. The fitting shall be made up of M.S. powder coated provided with electronic ballast, 1 no. 15/20 W LED lamp duly wired upto the connector block etc. complete as required. 886 Cirrus Mini Pro 15 / 20 watt & 1100 /1600 Lumens (Philips SM200C LED11S 6500 PSU OD WH) 887 Supplying of bulk head fittings suitable for 10 W LED lamp complete with ballast & accessories such as glass, wire guard, 60 W CFL lamp etc. complete as required. 888 Endural LED-Bulkhead, 10 W, 600 lumen Such as (Philips WT202W LED6S CW PSU S2 PC) 889 Supplying of exhaustfan, all complete with mounting ring frame i/c bracket,but without regulator with shutters in the following sizes. (G.E. ALSTHOM, KHAITAN & HAVELLS COMPANY) 890 300 mm 4 Pole 891 Supplying of 1400 mm sweep A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply. (CROMPTON, KHAITAN & HAVELLS COMPANY) 892 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 893 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 894 Installation, testing and commissioning of pre-wired, Light Fixture / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 895 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 896 Upto 450 mm sweep 897 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 898 Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. 899 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. 900 SUBHEAD - III - DISTRIBUTION BOARD 901 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 902 6 way (4 + 18), Double door 903 Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 904 100 A 905 Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 906 63 A 907 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 908 40 amps 909 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 910 12 way , Double door 911 16 way , Double door 912 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 913 25 A 914 40 A 915 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 916 Single pole 917 SUBHEAD - IV - EARTHING 918 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 919 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. 920 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 921 SUBHEAD - V - STREET LIGHTING ON BUILDING 922 Supplying, installing, testing and commissioning of 2 x 36W general purpose flourescent street light fittings with sheet aluminium housing and UV stabilized acrylic cover complete with chokes, starter holders, condensers, reflector cover etc. as reqd. (Philips Cat No. TRC 33 / 236 HPF) (To be fixed directly on wall of building) 923 Supplying and fixing of 32 mm dia X 2.00 meter long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 Nos. 40 mm X 3 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required. 924 Supply of following sizes of FRLS 1.1 KV stranded compact circular aluminium conductor screened with extruded semi conducting compound, XLPE insulated,Al round wire armoured & overall PVC sheathed cableconforming to IS to IS 7098 (Part-I) with latest amendments 925 2 x 4 sq.mm 926 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. 927 Upto 35 sq. mm 928 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 929 Upto 35 sq. mm 930 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size on wall surface as required. 931 Upto 35 sq. mm (clamped with 1mm thick saddle) 932 Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. 933 2 X 6 sq. mm (19mm) 934 Supply & fixing of 150x200 mm 60mm deep MS junction box recess or surface on wall with 3mm bakalite cover15 overlapping 15 all sides of junction Box & housing 4way 32amps bakelie connector to terminate incoming & outgoing armoured cable & & wiring the light fixture with 3x1.5 sq mm PVC insulated coppwer wire including interconnection ets as reqired .( Cost of termination of armoured cable with gland is not to be included as the same is payable under separate item no 5.07 of this SUBHEAD) 935 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing withcement mortar1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required. 936 100 mm dia 937 SUBHEAD - VI - LIGHTNING CONDUCTOR 938 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 939 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 940 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 941 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 942 Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chucknuts and spring washers etc. complete as required. 943 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrodedirectly in ground as required 944 [ VICE PRINCIPAL RESIDENCE ] 945 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 946 all kinds of soil 947 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 948 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 949 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 950 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 951 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 952 Upto plinth level 953 (i) R.C.C. work in Footing 954 (ii) R.C.C. work in Beam 955 (iii) R.C.C. work in Columns 956 (iv) R.C.C. work in Grade Slab 957 Above plinth to floor-V lvl 958 Same as above but R.C.C. work abive plinth Lvl. 959 (i) R.C.C. work in Lintel 960 (ii) R.C.C. work in Beam 961 (iii) R.C.C. work in Columns 962 (iv) R.C.C. work in Slab 963 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 964 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500 D or more. 965 Add for plaster drip course/ groove in plastered surface or moulding toR.C.C. projections. 966 Centering and shuttering including strutting, propping etc. and removal of form for all heights : 967 Foundations, footings, bases of columns, etc. for mass concrete. 968 Suspended floors, roofs, landings, balconies and access platform. 969 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 970 Columns,Pillars, Piers, Abutments, Posts and Struts. 971 Edges of slabs and breaks in floors and walls 972 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 973 Cement mortar 1:6 (1 cement : 6 coarse sand) 974 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 975 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 976 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 977 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 978 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 979 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 980 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 12.19.1 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 981 Providing and fixing 35 mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15:2001 (Part B), including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, all complete as per directions of Engineerin- charge and panelling with panels of : 12 mm thick one side Pre-laminated particle board (decorative lamination on one side and other sides balancing lamination) grade -1, medium density flat pressed, three layer particle board FPT - I or graded wood particle board FPT-1 conforming to IS : 3087 bonded with BWP type synthetic resin adhesive as per IS : 848 and pre-laminated conforming to IS : 12823, Grade -1, Type II marked : 982 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick 983 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 984 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer 985 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size 986 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. 987 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube 988 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 989 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 990 Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), ,uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 991 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. 992 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes. 993 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 994 30 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood 995 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 996 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 997 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and1.4 mm aperture on both sides 998 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 999 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand) 1000 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand) 1001 6 mm cement plaster on celling (a) 1:3(1 cement:3 fine sand) 1002 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floatingcoat of neat cement. 1003 20 mm cement plaster 1004 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 1005 Brick edging in full brick width and half brick depth including excavation refilling and disposal of surplus earth lead upto 50 metres. With common burnt clayF.P.S.(non modulur)bricks of class designation 75 1006 Providing and fixing glass strips in joints of terrazo/ cement concretefloors. 1007 40 mm wide and 4 mm thick 1008 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm. 1009 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm 1010 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick 1011 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1012 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Area of slab upto 0.50 sqm 1013 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 1014 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1015 P/F curtain rods of 1.25mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs etc. wherever necessary complete (a) 25 mm dia. 1016 Providing edge moulding to 18mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1017 Granite work 1018 Extra for fixing marble /granite stone over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive including cleaning etc. complete. 1019 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/Granite/stone work including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1020 Steel Painting: 1021 (a) With ready mixed red oxide zink chromate primer of approved brand and manufacture on steel galvanised iron/steel works. 1022 (b) Painting withsynthetic enamel paint of approvedbrandand manufactureto give an even shade:Two or more coats on new work. 1023 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer. 1024 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade. New work (Two or more coats applied @ 1.43 ltr/ 10 sqm. over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm). 1025 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 1026 Two or more coats on new work 1027 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1028 Providing and fixing ISI marked oxidised M.S. single acting spring hingeswith necessary screws etc. complete : 1029 150 mm 1030 Providing and fixing oxidised M.S. hasp and staple (safety type)conforming to IS : 363 with necessary screws etc. complete : 1031 90 mm 1032 Providing and fixing special quality bright finished brass cupboard orward robe locks with four levers of approved quality including necessaryscrews etc. complete. 1033 75 mm 1034 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 1035 50x50 mm (base and height) 1036 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 1037 250x16 mm 1038 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1039 200x10 mm 1040 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1041 125 mm 1042 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. Twin rubber stopper 1043 Providing and fixing bright finished brass casement stays(straight peg type) with necessary screws etc. complete.300 mm weighing not less than 330gms. 1044 300 mm weighing not less than 330 gms 1045 250 mm weighing not less than 280 gms 1046 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1047 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws 1048 Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). 1049 Float glass panes 4.0 mm thick glass panes (weight not less than 10 kg/sqm). 1050 Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, Parryware/Hindware/Seabird/Orient (Coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required. 1051 White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests 1052 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 1053 W.C. pan with ISI marked white solid plastic seat and lid 1054 Providingandfixing P.V.C. waste pipe forsink or wash basin including PVC waste fittings complete. 1055 Flexible Pipe 1056 32 mm dia (for wash basin) 1057 40 mm dia(for sink and urinal) 1058 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 1059 Kitchen sink with drain board 1060 510x1040 mm bowl depth 250 mm 1061 Kitchen sink without drain board 1062 610x510 mm bowl depth 200 mm 1063 Providing and fixing wash basin with C.I.brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,includingpainting of fittings and brackets, cutting and making good the walls wherever required 1064 White Vitreous china wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap 1065 Providing and fixing CP Brass 32mm size Bottle Trap of bapproved quality & make and as per the direction of Engineerin- charge. 1066 Providing & fixing C.P. Brass health faucet for ablution with 1 meter long PVC tube, hand shower, couplings, wall hook and other accessories. 1067 Providing & fixing CP brass Overhead shower with shower arm, Hand Shower 95mm dia Single Lever Concealed Deusch Mixer with Provision for Connection to Overhead Shower and Easy flex Tube with accessories complete I allrespect 1068 Providing & fixing C.P. Brass Waste Coupling for PVC waste Pipe. 1069 Providing & Fixing 600 X 450 mm bevelled edge mirror of superiorglass (of approved quality) complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1070 Providing & fixing toilet paper holder. 1071 viterous china 1072 Providing and fixing of C. P. brass towel rail 600 x 20 mm size complete with C.P. brass brackets 1073 Providing and fixing of C. P. brass towel ring complete with C.P. brass brackets 1074 Providing and fixing CP Brasssoap dish 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket and all fittings of the same material of approved quality and colour. 1075 Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipesfor soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors),reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor & basement ceiling / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. 1076 The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 1077 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) 1078 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) 1079 Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger, socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp & hangers etc. cutting holes in wall/ floors/ slabs and making good the same with cement concrete 1:2:4 complete as required. 1080 32 mm dia. 1081 40 mm dia. 1082 Providing & fixing UPVC Floor trap of self cleansing designwith stainless steel grating complete in all respects. 1083 Multi Floor Trap (5 Ht) with height raiser and branch saddle strip of 50/75 mm outlet 1084 Plain Floor Trap (4 Ht) with 50 / 75 outlet and with height raiser 1085 P-Trap type Floor Trap 110 x 75 mm 1086 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. 1087 Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover with screws and other required fitting complete as required. 1088 Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipesfor rain water disposal, Type-B as perIS : 13592 suitable for rubber ring joints, including all neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or without doors), reducers, couplers, expansion joints / bellows, cowels, clamps, rubber rings, MS gratings over pipes of bell mouth construction with epoxy painting etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc. in concealed / inside duct / under floor / external work etc. including chase cutting as required, excavation and back filling in all kind of soils, suspended from floor under false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including cost of shuttering for proper completion of the work, breaking and making good the walls and floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382. 1089 The Pipes will be supported with threaded G I rods & clamps on 50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-charge at site. 1090 110 mm dia 1091 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1092 Providing&fixing15 mm nominal bore45 cm long unplasticised PVC connection pipewith brass unions. 1093 45 cm length 1094 15 mm nominal bore 1095 Providing and fixing C.P brass bib cock of approved qualityconforming to IS standards IS: 8931. 1096 15 mm nominal bore 1097 Providing and fixing C.P brass long nose bib cock of approved qualityconforming to IS standardsandweighing notlessthan 810 gms. 1098 15 mm nominal bore 1099 Providing & fixing 15 mm nominal bore C.P brass Angle valve for basin mixer and geyser points of approved quality conformingto IS8931. 1100 15 mm nominal bore 1101 Constructing brick masonry chamber 300 x 300x500mm, insidewithF.P.S. brick work in cement mortar 1: 4 (1 cement : 4 coarse sand) for StopCock, withC. I. surface box 100 x 100 x 75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4mix (1cement : 2 coarse sand:4 grade stone aggregate 20mm nominal size); necessary excavation, foundationconcrete 1:5:10 (1 cement :5 fine sand: 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar1 : 3 (1 cement : 3 coarse sand )12mmthick finished with a floatingcoatof neat cementcomplete as per standard design 1102 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 1103 Providing & Fixing G.I. Unoun in G.I. pipe including cutting and threading the pipe & making long screws etc. complete. 1104 15mm dia nominal bore 1105 20mm dia nominal bore 1106 25mm dia nominal bore 1107 32mm dia nominal bore 1108 40mm dia nominal bore 1109 50mm dia nominal bore 1110 65mm dia nominal bore 1111 Cutting holes up to 30 X 30 cm in walls including making good the same: 1112 With common burnt clay F.P.S. (non modular) bricks 1113 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipesCTS-SDR 11, class-1 CPVC Pipes (pressure rating 28 kg/cm2 at 23oC and 7 kg/cm2 at 82oC) confirming to IS : 15778-2007, ASTM D-2846, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in charge. 1114 Internal work exposed on wall 1115 20mm nominal outer dia pipes 1116 25mm nominal outer dia pipes 1117 32mm nominal outer dia pipes 1118 40mm nominal outer dia pipes 1119 50mm nominal outer dia pipes 1120 Providing, fixing chlorinated polyvinyl Chloride (CPVC) pipesCTS-SDR 11, class-1 CPVC Pipes (pressure rating 28 kg/cm2 at 23oC and 7 kg/cm2 at 82oC) confirming to IS : 15778-2007, ASTM D-2846, havingthermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge. 1121 Concealed work including cutting chase and making good the wall etc. 1122 15mm nominal outer dia pipes 1123 20mm nominal outer dia pipes 1124 25mm nominal outer dia pipes 1125 32mm nominal outer dia pipes 1126 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1127 Circular tank 1128 Providing & fixing of hand lever operated forged brass body full way ball valve type isolating valve having forged brass hard chrome plated mirror finish ball, steel handle with PVC grip, teflon seat, screwed ends tested to a pressure of 15 kg/sqcm complete. 1129 15 mm nominal bore 1130 20 mm nominal bore 1131 25 mm nominal dia 1132 32 mm nominal bore 1133 40 mm nominal bore 1134 50 mm nominal dia 1135 Providing & fixing brass ball float valvewith bronzefloats of approved quality complete. 1136 20 mm nominal dia 1137 25 mm nominal dia 1138 Providing & fixing of medium class G.I.spout up to 300 mm. length including cutting and making good the walls and floors etc. as required. 1139 a) 25 mm dia 1140 Point wiring in PVC conduit, with modular type switch :- 1141 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1142 Group C 1143 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. 1144 Group C 1145 Twin Control Point wiring in PVC conduit, with modular type switch :- 1146 Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class pvc conduit, 2 way modular switch, modular switch, suitable M.S. box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1147 Power plug wiring in PVC conduit (2 x 4 Sq.Mm.) :- 1148 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class pvc conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 1149 Circuit / Sub main wiring in PVC conduit :- 1150 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class pvc conduit as required. 1151 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire. 1152 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire. 1153 2 x 6 sq.mm. + 1 x 6 sq.mm. Earth wire 1154 2 x 10 sq.mm. + 1 x 6 sq.mm. Earth wire 1155 4 x 10 sq.mm. + 2 x 6 sq.mm. Earth wire 1156 S/F light plug point Modular type accessories :- 1157 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required 1158 S/F power plug point modular type accessories :- 1159 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 1160 Supplying and fixing 20 amps, 240 volts, SPN, industrial type socket outlet, with 2 poles and earth metal enclosedplug top alongwith 20amps. C curve, SP MCB in sheet steel enclosure, on surface or in recess, with chainedmetal cover for the socket outlet, and complete with connections, testingandcommissioning etc. as required. 1161 S/F modular type electronic fan regulator :- 1162 Supply and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 1163 S/F modular type blanking plate :- 1164 Supply and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. 1165 SUB HEAD (II) :- DISTRIBUTION BOARDS & MCBs 1166 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 1167 8 way , Double door 1168 Supplying and fixing followingway, horizontal type TP&N, sheet steelMCB distribution board,415 V on surface /recess,completewithtinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required (But without MCB / RCCB / Isolators). 1169 8 way (4 + 24), Double door 1170 Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,residual current circuit breaker (RCCB), having a sensitivity current upto 30 mA in the existingMCBDBcomplete with connections, testing andcommissioning etc. as required. 1171 63 amps. 1172 Supplying and fixing 5 amps. to 32 amps. rating, 240 volts `C series,miniature circuit breaker (MCB)suitable for inductive load offollowingpolesin the existingMCBDBcomplete with connections, testing andcommissioning etc. as required. 1173 single pole 1174 Supplying & fixing single pole, blanking plate in the existing MCBDBcomplete etc. as required. 1175 Supplying and fixing following rating, Single/ double/ three pole, 230/ 415 volts, MCB C curve in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1176 63 amps FP MCB 1177 40 amps DP MCB 1178 SUB HEAD (III) :- TELEPHONE, TELEVISION & DATA SYSTEM 1179 S/F MODULAR BOXES, BASE & COVER PLATE :- 1180 Supplying and fixing following size / modules, GI box along with modular base & cover plate for modular switches inrecessetc as required 1181 1 or 2 Module (75 mm x 75 mm) 1182 S/F MODULAR TYPE SWITCH / SOCKET :- 1183 Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc as required 1184 Telephone Socket outlet 1185 TV Antenna socket outlet 1186 Supply and fixing offollowingsizes of medium class PVC conduit along with accessories in surface/recess including cuttingthe wall and making good the same in case of recessed conduit as required : 1187 20 mm. 1188 25 mm. 1189 Supply and drawing followingpair, 0.5 sq.mm. FRLS PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface / recessed steel/ PVC conduit as required. 1190 2 Pair 1191 Supply and drawing co-axial TV cable RG-6 grade, 0.7 mm. Solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed steel/ PVC conduit as required. 1192 SUB HEAD (IV) :- MISCELLANEOUS 1193 Providing and fixing M.V. dangernotice plate of 200mmx150mm made of mild steel, atleast 2mm thick and vitreous enamelled white on both sides and with inscription singleredcolouronFRLSontsideas required. 1194 Supplying and fixing call bell/buzzer suitablefor single phase, 230 volts, complete as required. 1195 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box forceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding,top lid shall be screwed into the cast iron/ M.S. sheet box by means of3.3 mm dia round headed screws, one lock at the corners. Clamp shallbe made of 12 mm dia M.S. bar bent to shape as per standard drawing. 1196 SUB HEAD(V):-INTERNAL LIGHTING FIXTURES & FANS 1197 SUPPLY OF LIGHTING FIXTURES 1198 Supply of 15W SURFACE MOUNTED LED with all accessories as per standard item..(Such as Panasonic ADL04R156 or Equivalent). 1199 Supply of 15W WALL BRACKET LED BULB with all accessories as per standard item..(Such as Panasonic PBUM01157 or Equivalent). 1200 Supply of 20W SURFACE MOUNTED LED with all accessories as per standard item..(Such as Panasonic ADL04R206 or Equivalent). 1201 Supply of 20W SURFACE MOUNTED LED TUBE with all accessories as per standard item..(Such as Panasonic PBTM01207 or Equivalent). 1202 SUPPLY OF CEILING & EXHAUST FANS 1203 Supply of AC230/250 volts, 50 HZceiling fanwith standarddownrod, blades, 2 nos. caps & regulator etc. ISI with 5 star marked & energy efficient complete as required. (Such as Havells Velocity/Velocity HS or Equivalent). 1204 1200 mm sweep 1205 Supply of AC230/250 volts, 50 HZ exhaust fansincluding providingnuts, bolts, mounting FRLSame and other accessories etc. Complete as required (Such as Ventil Air - DX White or Equivalent). 1206 300 mm sweep 900 rpm 1207 ERECTIONOFLIGHTINGFIXTURESANDFANS 1208 Installation, testing and commissioning of pre-wired, flourescent fitting / compact fluorescent fitting of all types, complete with all accessories and tubes etc. directly on ceiling / wall, including connection with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 1209 Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq. mm. FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 1210 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required 1211 Upto 450 mm sweep 1212 SUB HEAD(VI):-LIGHTNING CONDUCTOR 1213 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 1214 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 1215 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 1216 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 1217 Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chucknuts and spring washers etc. complete as required. 1218 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrodedirectly in ground as required 1219 EARTH WORK 1220 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1221 All kinds of soil 1222 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 1223 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 1224 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 1225 CONCRETE WORK 1226 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1227 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 1228 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1229 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 1230 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 1231 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 1232 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 1233 REINFORCEDCEMENTCONCRETE 1234 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 1235 Foundations, footings, bases of columns, etc. for mass concrete 1236 Columns, Pillars, Piers, Abutments, Posts and Struts 1237 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 1238 Edges of slabs and breaks in floors and walls 1239 Under 20 cms wide 1240 Suspended floors, roofs, landings, balconies and access platform. 1241 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 1242 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 1243 Thermo-Mechanically Treated bars of grade Fe-500D or more. 1244 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 1245 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 1246 All works upto plinth level 1247 All works above plinth level upto floor V level 1248 BRICK WORK 1249 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 1250 Cement mortar 1:6 (1 cement : 6 coarse sand) 1251 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 1252 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 1253 Cement mortar 1:4 (1 cement :4 coarse sand) 1254 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 1255 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 1256 MARBLE WORK 1257 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 1258 Granite of any colour and shade 1259 Area of slab over 0.50 sqm 1260 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1261 Granite work 1262 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 1263 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1264 WOOD WORK & PVC WORK 1265 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 1266 Second class teak wood 1267 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 1268 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 1269 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws 1270 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1271 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 1272 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 1273 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 1274 35 mm thick shutters 1275 Kiln seasoned and chemically treated hollock wood 1276 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 1277 Fixed to steel windows by welding 1278 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 1279 With 12 mm mild steel U beading 1280 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 1281 250 mm weighing not less than 150 gms 1282 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 1283 250x16 mm 1284 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1285 200x10 mm 1286 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1287 125 mm 1288 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 1289 Twin rubber stopper 1290 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1291 1.5 mm thick 1292 Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. 1293 With decorative veneering on one side and commercial veneering on other side 1294 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 1295 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 1296 Providing and fixing ISI marked oxidised M.S. single acting spring hingeswith necessary screws etc. complete : 1297 150 mm 1298 Providing and fixing oxidised M.S. hasp and staple (safety type)conforming to IS : 363 with necessary screws etc. complete : 1299 90 mm 1300 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 1301 75 mm 1302 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 1303 50x50 mm (base and height) 1304 Float glass panes 1305 4.0 mm thick glass panes (weight not less than 10 kg/sqm). 1306 STEEL WORK 1307 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 1308 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1309 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 1310 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1311 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 1312 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 1313 4.0 mm thick glass panes 1314 FLOORING 1315 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 1316 25 mm thick. 1317 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 1318 40 mm wide and 4 mm thick 1319 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1320 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 1321 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. 1322 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1323 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 1324 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 1325 Size of Tile 600x600 mm 1326 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. 1327 Size of Tile 600x600 mm 1328 ROOFING 1329 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat. 1330 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 1331 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1332 FINISHING 1333 12 mm cement plaster of mix 1334 1:6 (1 cement: 6 coarse sand) 1335 15 mm cement plaster on rough side of single or half brick wall of mix: 1336 1:6 (1 cement: 6 coarse sand) 1337 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. 1338 20 mm cement plaster 1339 6mm cement plaster of mix 1340 1:3 (1 cement : 3 fine sand) 1341 White washing with lime to give an even shade : 1342 New work (three or more coats) 1343 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1344 New work (two or more coats) over and including water thinnable priming coat with cement primer 1345 Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade: 1346 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 1347 Applying priming coat: 1348 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 1349 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 1350 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 1351 Two or more coats on new work 1352 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 1353 Two or more coats on new work 1354 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1355 WATER PROOFING 1356 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 1357 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 12.19.1 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 1358 GUEST HOUSE(SANITARY WORKS) 1359 EARTH WORK 1360 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1361 All kinds of soil. 1362 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1363 All kinds of soil 1364 Pipes, cables etc, not exceeding 80 mm dia. 1365 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 1366 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 1367 ROOFING 1368 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 1369 110 mm diameter 1370 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 1371 Coupler 1372 110 mm 1373 Bend 87.5° 1374 110 mm bend 1375 Shoe (Plain) 1376 110 mm Shoe 1377 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1378 110 mm 1379 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 1380 SANITARY INSTALLATIONS 1381 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1382 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 1383 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 1384 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 1385 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 1386 Kitchen sink with drain board 1387 510x1040 mm bowl depth 250 mm 1388 Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. 1389 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1390 Providing and fixing toilet paper holder : 1391 Vitreous china 1392 Providing and fixing soil, waste and vent pipes : 1393 100 mm dia. 1394 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 1395 75mm diameter 1396 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 1397 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 1398 For 100 mm dia. pipe 1399 For 75 mm dia. pipe 1400 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1401 100 mm 1402 Sand cast iron S&S as per IS - 3989 1403 75 mm 1404 Sand cast iron S&S as per IS- 3989 1405 Providing and fixing plain bend of required degree. 1406 100 mm 1407 Sand cast iron S&S as per IS : 3989 1408 75 mm 1409 Sand cast iron S&S as per IS - 3989 1410 Providing and fixing heel rest sanitary bend 1411 100 mmdia 1412 Sand cast iron S&S as per IS - 3989 1413 75 mm dia 1414 Sand cast iron S&S as per IS - 3989 1415 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick,bolts and nuts complete. 1416 100x100x100mm 1417 Sand cast iron S&S as per IS - 3989 1418 75x75x75mm 1419 Sand cast iron S&S as per IS - 3989 1420 Providing and fixing single equal plain junction of required degree 1421 100x100x100mm 1422 Sand cast iron S&S as per IS - 3989 1423 75x75x75mm 1424 Sand cast iron S&S as per IS - 3989 1425 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 1426 100 mm 1427 Sand cast iron S&S as per IS - 3989 1428 75 mm 1429 Sand cast iron S&S as per IS - 3989 1430 Providing and fixing terminal guard : 1431 100 mm 1432 Sand cast iron S&S as per IS - 3989 1433 75 mm 1434 Sand cast iron S&S as per IS - 3989 1435 Providing and fixing collar : 1436 100 mm 1437 Sand cast iron S&S as per IS - 3989 1438 75 mm 1439 Sand cast iron S&S as per IS - 3989 1440 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 1441 100 mm 1442 75 mm 1443 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 1444 100 mm 1445 75 mm 1446 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 1447 100 mm inlet and 100 mm outlet 1448 Sand Cast Iron S&S as per IS: 1729 1449 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 1450 100 mm dia 1451 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 1452 100 mm diameter pipe 1453 75 mm diameter pipe 1454 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 1455 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 1456 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 1457 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 1458 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 1459 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 1460 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1461 Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling. 1462 External work 1463 32mmdia nominal bore 1464 40mmdia nominal bore 1465 50mmdia nominal bore 1466 WATER SUPPLY 1467 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 1468 Internal work - Exposed on wall 1469 25 mm nominal outer dia Pipes metre 1470 32 mm nominal outer dia Pipes metre 1471 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1472 Concealed work, including cutting chases and making good the walls etc. 1473 15 mm nominal outer dia Pipes 1474 20 mm nominal outer dia Pipes 1475 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 1476 25 to 40 mm nominal bore 1477 Providing and fixing brass stop cock of approved quality : 1478 15 mm nominal bore 1479 20 mm nominal bore 1480 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1481 25mm nominal bore 1482 32mm nominal bore 1483 40mm nominal bore 1484 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1485 25 mm nominal bore 1486 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 1487 25 mm nominal bore 1488 Providing and fixing uplasticised PVC connection pipe with brass unions : 1489 45 cm length 1490 15 mm nominal bore 1491 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 1492 100 mm diameter 1493 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1494 Rectangular tank 1495 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 1496 15 mm nominal bore 1497 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 1498 15 mm nominal bore 1499 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1500 15 mm nominal bore. 1501 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1502 15 mm nominal bore 1503 Providing and fixing PTMT grating of approved quality and colour. 1504 Circular type. 1505 100 mm nominal dia. 1506 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 1507 SEWARAGE & DRAINAGE 1508 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 1509 100 mm diameter 1510 150 mm diameter 1511 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 1512 100 mm diameter S.W. pipe 1513 150 mm diameter S.W. pipe 1514 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 1515 150 x 100 mm size P type 1516 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1517 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 1518 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 1519 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1520 Extra for depth for manholes : 1521 Size 90x80 cm 1522 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1523 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 1524 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 1525 For pipes 100 to 250 mm diameter 1526 Providing, laying and jointing non pressure NP2 class (light duty)RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 1527 150 mm dia RCC pipe 1528 GUEST HOUSE (ELECTRICAL WORKS) 1529 SUBHEAD - I - WIRING 1530 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1531 Group C 1532 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 1533 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1534 4 Module (125 mmX75 mm) 1535 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1536 15/16 A switch 1537 3 pin 5/6 A socket outlet 1538 Telephone socket outlet 1539 TV antenna socket outlet 1540 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 1541 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire 1542 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 1543 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 1544 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 1545 25 mm 1546 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1547 1 or 2 Module (75 mmX75 mm) 1548 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1549 2 Pair 1550 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1551 20 mm 1552 25 mm 1553 Providing and fixing in position 2mm thick M.S. Telephone junction box of size suitable for fixing of following Krone Tag Block with key lock arrangement. Also provide clamps for fixing tag blocks. 1554 10 pair Telephone Tag Blockwith box 1555 Supplying, laying of 10 pair unarmoured PVC insulated copper conductor (ATC) telephone cable in ground/existing pipes/on wall and making connection with telephone main junction box (MDF) including supports and all accessories as required 1556 10 Pair Cable unarmoured 1557 SUBHEAD - II - SUPPLY & INSTALLATION OF FITTINGS 1558 Supplying of following box type Fl. fitting made out of CRCA sheet finished in antirust treated non-yellowing super white stove enamelled paint duly wired with copper wound heavy duty choke starter holder, starter but without lamp complete etc. as reqd. 1559 Mounting rail for TLED lamps 1600 Lumens (TMC 501 P 1xT-LED with Essential LED 18W Tube) 1560 Supplying of wall bracket light fittings suitable for 11 / 13 W CFL lamp. The fitting shall be made up of M.S. powder coated provided with integral ballast, frosted glass and 1 no. 11 / 13 Wlamp duly wired upto the connector block complete as required. (Decon Cat. No.05AAM) 1561 Supplying of ceiling light fittings suitable for 1 x 15/20 W LED lamp. The fitting shall be made up of M.S. powder coated provided with electronic ballast, 1 no. 15/20 W LED lamp duly wired upto the connector block etc. complete as required. 1562 Cirrus Mini Pro 15 / 20 watt & 1100 /1600 Lumens (Philips SM200C LED11S 6500 PSU OD WH) 1563 Supplying of bulk head fittings suitable for 10 W LED lamp complete with ballast & accessories such as glass, wire guard, 60 W CFL lamp etc. complete as required. 1564 Endural LED-Bulkhead, 10 W, 600 lumen Such as (Philips WT202W LED6S CW PSU S2 PC) 1565 Supplying of exhaustfan, all complete with mounting ring frame i/c bracket,but without regulator with shutters in the following sizes. (G.E. ALSTHOM, KHAITAN & HAVELLS COMPANY) 1566 300 mm 4 Pole 1567 Supplying of 1400 mm sweep A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply. (CROMPTON, KHAITAN & HAVELLS COMPANY) 1568 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 1569 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 1570 Installation, testing and commissioning of pre-wired, light fixture / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 1571 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 1572 Upto 450 mm sweep 1573 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 1574 Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. 1575 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. 1576 SUBHEAD - III - DISTRIBUTION BOARD 1577 Supplying, installing, testing and commissioning of compartmentalised cubical type meter board for installation of single phase meter. The cubical board shall be made of 2mm thick C.R.C.A sheet, duly phosphatised powder coated complete with connection bus bar and following accessories mounted in it. 1578 METER BOARD 1579 INCOMING : 1580 40A TP MCCB having breaking capacity - 25 KA - 1 No. 1581 OUTGOING : 1582 Space for Single phase energy meter - 4 Nos. 1583 25 Amp DP MCB - 4 Nos. 1584 Supplying, installing, testing & commissioning of Single Phase Electronic Energy Meter, tested as per Electricity Boards requirement. 1585 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 1586 12 way, SPN 1587 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1588 40 amps 1589 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired. 1590 25 amps 1591 Supplying of XLPE insulated, PVC sheathed 1.1 KV grade Aluminium conductor heavy duty armoured cable as per IS : 7098 of size : 1592 4 x 16 sq.mm. 1593 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required for crossing road/walls 1594 100 mm dia 1595 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 1596 Single pole 1597 SUBHEAD - IV - EARTHING 1598 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 1599 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. 1600 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 1601 STAFF QUARTERS TYPE III 10 Nos CIVIL WORK 1602 EARTH WORK 1603 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1604 All kinds of soil 1605 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 1606 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 1607 Supplying chemical emulsion in sealed containers including delivery as specified. 1608 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 1609 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 1610 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 1611 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 1612 Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5km also includingramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete. 1613 CONCRETE WORK 1614 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1615 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 1616 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 1617 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 1618 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 1619 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 1620 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 1621 REINFORCEDCEMENTCONCRETE 1622 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 1623 Foundations, footings, bases of columns, etc. for mass concrete 1624 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 1625 Columns, Pillars, Piers, Abutments, Posts and Struts 1626 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 1627 Edges of slabs and breaks in floors and walls 1628 Under 20 cms wide 1629 Suspended floors, roofs, landings, balconies and access platform. 1630 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 1631 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 1632 50 mm thick 1633 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 1634 Thermo-Mechanically Treated bars of grade Fe-500D or more. 1635 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 1636 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 1637 All works upto plinth level 1638 All works above plinth level upto floor V level 1639 Add for using extra cement in the items of design mix over and above the specified cement content therein. 1640 BRICK WORK 1641 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 1642 Cement mortar 1:6 (1 cement : 6 coarse sand) 1643 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 1644 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 1645 Cement mortar 1:4 (1 cement :4 coarse sand) 1646 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 1647 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 1648 MARBLE WORK 1649 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 1650 Granite of any colour and shade 1651 Area of slab over 0.50 sqm 1652 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 1653 Granite work 1654 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 1655 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 1656 WOOD WORK & PVC WORK 1657 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 1658 Second class teak wood 1659 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 1660 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 1661 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws 1662 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1663 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 1664 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 1665 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 1666 35 mm thick shutters 1667 Kiln seasoned and chemically treated hollock wood 1668 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 1669 Fixed to steel windows by welding 1670 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 1671 With 12 mm mild steel U beading 1672 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 1673 250 mm weighing not less than 150 gms 1674 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 1675 250x16 mm 1676 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1677 200x10 mm 1678 Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyedto required colour or shade, with necessary screws etc. complete : 1679 125 mm 1680 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 1681 Twin rubber stopper 1682 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1683 1.5 mm thick 1684 Providing and fixing Pre-laminated flat pressed 3 layer (medium density)particle board or graded wood particle board IS : 3087 marked, with oneside decorative and other side balancing lamination Grade I, Type IIexterior grade IS : 12823 marked, in shelves with screws and fittingswherever required, edges to be painted with polyurethane primer (fittingsto be paid separately). 1685 18 mm thick 1686 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 1687 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 1688 Providing and fixing ISI marked oxidised M.S. single acting spring hingeswith necessary screws etc. complete : 1689 150 mm 1690 Providing and fixing oxidised M.S. hasp and staple (safety type)conforming to IS : 363 with necessary screws etc. complete : 1691 90 mm 1692 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 1693 75 mm 1694 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 1695 50x50 mm (base and height) 1696 Float glass panes 1697 4 mm thick glass pane (weight not less than 10kg/sqm). 1698 STEEL WORK 1699 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 1700 Using M.S. angles 40x40x6 mm for diagonal braces 1701 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 1702 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1703 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 1704 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 1705 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 1706 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 1707 M.S. tube 1708 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 1709 4.0 mm thick glass panes 1710 FLOORING 1711 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 1712 40 mm wide and 4 mm thick 1713 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 1714 25 mm thick. 1715 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 1716 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 1717 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. 1718 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 1719 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 1720 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 1721 Size of Tile 600x600 mm 1722 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. 1723 Size of Tile 400x400 mm 1724 ROOFING 1725 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat. 1726 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 1727 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 1728 FINISHING 1729 12 mm cement plaster of mix 1730 1:6 (1 cement: 6 coarse sand) 1731 15 mm cement plaster on rough side of single or half brick wall of mix: 1732 1:6 (1 cement: 6 coarse sand) 1733 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floatingcoat of neat cement. 1734 20 mm cement plaster 1735 6mm cement plaster of mix 1736 1:3 (1 cement : 3 fine sand) 1737 White washing with lime to give an even shade : 1738 New work (three or more coats) 1739 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 1740 New work (two or more coats) over and including water thinnable priming coat with cement primer 1741 Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade: 1742 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 1743 Applying priming coat: 1744 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 1745 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 1746 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 1747 Two or more coats on new work 1748 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 1749 Two or more coats on new work 1750 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1751 WATER PROOFING 1752 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 1753 Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. 1754 Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. 1755 After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. 1756 Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. 1757 The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 1758 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 1759 Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. 1760 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 1761 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 1762 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). 1763 NON SHEDULE ITEMS 1764 Providing and laying cinder filling in sunken floors and other locationswith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawings and as directed by the Engineer in Charge. 1765 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1766 150 mm 1767 Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in-Charge : 1768 Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc complete in all respects as per specifications/drawings and to the entire satisfaction to the Architect. 1769 STAFF QUARTER-III (G+1) 10 NOSPLUMBING WORK 1770 EARTH WORK 1771 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1772 All kinds of soil. 1773 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 1774 All kinds of soil 1775 Pipes, cables etc, not exceeding 80 mm dia. 1776 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 1777 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 1778 ROOFING 1779 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 1780 110 mm diameter 1781 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 1782 Coupler 1783 110 mm 1784 Bend 87.5° 1785 110 mm bend 1786 Shoe (Plain) 1787 110 mm Shoe 1788 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 1789 110 mm 1790 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 1791 SANITARY INSTALLATIONS 1792 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1793 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 1794 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 1795 W.C. pan with ISI marked white solid plastic seat and lid 1796 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 1797 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 1798 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 1799 Kitchen sink with drain board 1800 510x1040 mm bowl depth 250 mm 1801 Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. 1802 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 1803 Providing and fixing toilet paper holder : 1804 Vitreous china 1805 Providing and fixing soil, waste and vent pipes : 1806 100 mm dia. 1807 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 1808 75mm diameter 1809 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 1810 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 1811 For 100 mm dia. pipe 1812 For 75 mm dia. pipe 1813 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 1814 100 mm 1815 Sand cast iron S&S as per IS - 3989 1816 75 mm 1817 Sand cast iron S&S as per IS- 3989 1818 Providing and fixing plain bend of required degree. 1819 100 mm 1820 Sand cast iron S&S as per IS : 3989 1821 75 mm 1822 Sand cast iron S&S as per IS - 3989 1823 Providing and fixing heel rest sanitary bend 1824 100 mmdia 1825 Sand cast iron S&S as per IS - 3989 1826 75 mm dia 1827 Sand cast iron S&S as per IS - 3989 1828 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick,bolts and nuts complete. 1829 100x100x100mm 1830 Sand cast iron S&S as per IS - 3989 1831 75x75x75mm 1832 Sand cast iron S&S as per IS - 3989 1833 Providing and fixing single equal plain junction of required degree 1834 100x100x100mm 1835 Sand cast iron S&S as per IS - 3989 1836 75x75x75mm 1837 Sand cast iron S&S as per IS - 3989 1838 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 1839 100 mm 1840 Sand cast iron S&S as per IS - 3989 1841 75 mm 1842 Sand cast iron S&S as per IS - 3989 1843 Providing and fixing terminal guard : 1844 100 mm 1845 Sand cast iron S&S as per IS - 3989 1846 75 mm 1847 Sand cast iron S&S as per IS - 3989 1848 Providing and fixing collar : 1849 100 mm 1850 Sand cast iron S&S as per IS - 3989 1851 75 mm 1852 Sand cast iron S&S as per IS - 3989 1853 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 1854 100 mm 1855 75 mm 1856 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 1857 100 mm 1858 75 mm 1859 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 1860 100 mm inlet and 100 mm outlet 1861 Sand Cast Iron S&S as per IS: 1729 1862 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 1863 100 mm dia 1864 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 1865 100 mm diameter pipe 1866 75 mm diameter pipe 1867 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 1868 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 1869 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 1870 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 1871 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 1872 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 1873 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 1874 Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling. 1875 External work 1876 32mmdia nominal bore 1877 40mmdia nominal bore 1878 50mmdia nominal bore 1879 WATER SUPPLY 1880 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 1881 Internal work - Exposed on wall 1882 25 mm nominal outer dia Pipes metre 1883 32 mm nominal outer dia Pipes metre 1884 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 1885 Concealed work, including cutting chases and making good the walls etc. 1886 15 mm nominal outer dia Pipes 1887 20 mm nominal outer dia Pipes 1888 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 1889 25 to 40 mm nominal bore 1890 Providing and fixing brass stop cock of approved quality : 1891 15 mm nominal bore 1892 20 mm nominal bore 1893 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 1894 25mm nominal bore 1895 32mm nominal bore 1896 40mm nominal bore 1897 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 1898 25 mm nominal bore 1899 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 1900 25 mm nominal bore 1901 Providing and fixing uplasticised PVC connection pipe with brass unions : 1902 45 cm length 1903 15 mm nominal bore 1904 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 1905 100 mm diameter 1906 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 1907 Rectangular tank 1908 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 1909 15 mm nominal bore 1910 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 1911 15 mm nominal bore 1912 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 1913 15 mm nominal bore. 1914 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 1915 15 mm nominal bore 1916 Providing and fixing PTMT grating of approved quality and colour. 1917 Circular type. 1918 100 mm nominal dia. 1919 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 1920 SEWARAGE & DRAINAGE 1921 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 1922 100 mm diameter 1923 150 mm diameter 1924 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 1925 100 mm diameter S.W. pipe 1926 150 mm diameter S.W. pipe 1927 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 1928 150 x 100 mm size P type 1929 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1930 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 1931 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 1932 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1933 Extra for depth for manholes : 1934 Size 90x80 cm 1935 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 1936 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 1937 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 1938 For pipes 100 to 250 mm diameter 1939 Providing, laying and jointing non pressure NP2 class (light duty)RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 1940 150 mm dia RCC pipe 1941 250 mm dia RCC pipe 1942 NON SHEDULE ITEMS 1943 Providing and fixing floor drain points of 75 x 50mmreducer bend with 100 mm dia CP grating with frame, embedded in floor including making joints with waste pipe etc. complete in all respects as per drawing and as directed by theEngineer in Charge. 1944 Providing & fixing Sink Mixer with Swinging Casted Spout (Wall Mounted Jaquar model CON-309 KN)/approved equal with 450mm long copper pipes & brass nuts. 1945 Providing and fixing concealed single leverbath & overhead shower mixer of hindware make and model No.(F360019CP) respectively or equivalent approved make as approved byEngineer in charge. 1946 Supplying, fixing, testing and commissioning of storage type water heater (Geyser) etc. with Stainless steel body , copper container , automatic thermostatic control electric element, pressure release valve, M.S. nuts and bolts etc. conforming to IS: 2082 1947 25 Litre Capacity 1948 STAFF QTRS TYPE III (G+1) 10 NOSELECTRICAL WORK 1949 SUBHEAD - I - WIRING 1950 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 1951 Group C 1952 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 1953 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1954 4 Module (125 mmX75 mm) 1955 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 1956 15/16 A switch 1957 3 pin 5/6 A socket outlet 1958 Telephone socket outlet 1959 TV antenna socket outlet 1960 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 1961 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire 1962 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 1963 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 1964 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 1965 25 mm 1966 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1967 1 or 2 Module (75 mmX75 mm) 1968 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 1969 2 Pair 1970 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 1971 20 mm 1972 25 mm 1973 Providing and fixing in position 2mm thick M.S. Telephone junction box of size suitable for fixing of following Krone Tag Block with key lock arrangement. Also provide clamps for fixing tag blocks. 1974 10 pair Telephone Tag Blockwith box 1975 Supplying, laying of 10 pair unarmoured PVC insulated copper conductor (ATC) telephone cable in ground/existing pipes/on wall and making connection with telephone main junction box (MDF) including supports and all accessories as required 1976 10 Pair Cable unarmoured 1977 SUBHEAD - II - SUPPLY & INSTALLATION OF FITTINGS 1978 Supplying of following box type Fl. fitting made out of CRCA sheet finished in antirust treated non-yellowing super white stove enamelled paint duly wired with copper wound heavy duty choke starter holder, starter but without lamp complete etc. as reqd. 1979 Mounting rail for TLED lamps 1600 Lumens (TMC 501 P 1xT-LED with Essential LED 18W Tube) 1980 Supplying of wall bracket light fittings suitable for 11 / 13 W CFL lamp. The fitting shall be made up of M.S. powder coated provided with integral ballast, frosted glass and 1 no. 11 / 13 Wlamp duly wired upto the connector block complete as required. (Decon Cat. No.05AAM) 1981 Supplying of ceiling light fittings suitable for 1 x 15/20 W LED lamp. The fitting shall be made up of M.S. powder coated provided with electronic ballast, 1 no. 15/20 W LED lamp duly wired upto the connector block etc. complete as required. 1982 Cirrus Mini Pro 15 / 20 watt & 1100 /1600 Lumens (Philips SM200C LED11S 6500 PSU OD WH) 1983 Supplying of bulk head fittings suitable for 10 W LED lamp complete with ballast & accessories such as glass, wire guard, 60 W CFL lamp etc. complete as required. 1984 Endural LED-Bulkhead, 10 W, 600 lumen Such as (Philips WT202W LED6S CW PSU S2 PC) 1985 Supplying of exhaustfan, all complete with mounting ring frame i/c bracket,but without regulator with shutters in the following sizes. (G.E. ALSTHOM, KHAITAN & HAVELLS COMPANY) 1986 300 mm 4 Pole 1987 Supplying of 1400 mm sweep A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply. (CROMPTON, KHAITAN & HAVELLS COMPANY) 1988 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 1989 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 1990 Installation, testing and commissioning of pre-wired, light fixture / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 1991 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 1992 Upto 450 mm sweep 1993 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 1994 Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. 1995 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. 1996 SUBHEAD - III - DISTRIBUTION BOARD 1997 Supplying, installing, testing and commissioning of compartmentalised cubical type meter board for installation of single phase meter. The cubical board shall be made of 2mm thick C.R.C.A sheet, duly phosphatised powder coated complete with connection bus bar and following accessories mounted in it. 1998 METER BOARD 1999 INCOMING : 2000 40A TP MCCB having breaking capacity - 25 KA - 1 No. 2001 OUTGOING : 2002 Space for Single phase energy meter - 4 Nos. 2003 25 Amp DP MCB - 4 Nos. 2004 Supplying, installing, testing & commissioning of Single Phase Electronic Energy Meter, tested as per Electricity Boards requirement. 2005 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2006 12 way, SPN 2007 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2008 40 amps 2009 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired. 2010 25 amps 2011 Supplying of XLPE insulated, PVC sheathed 1.1 KV grade Aluminium conductor heavy duty armoured cable as per IS : 7098 of size : 2012 4 x 16 sq.mm. 2013 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required for crossing road/walls 2014 100 mm dia 2015 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2016 Single pole 2017 SUBHEAD - IV - EARTHING 2018 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 2019 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. 2020 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 2021 SUBHEAD - V- LIGHTNING CONDUCTOR 2022 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 2023 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 2024 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 2025 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2026 Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chucknuts and spring washers etc. complete as required. 2027 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrodedirectly in ground as required 2028 STAFF QUARTERS TYPE II5 NosCivil Work 2029 EARTH WORK 2030 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2031 All kinds of soil 2032 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2033 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. 2034 Supplying chemical emulsion in sealed containers including delivery as specified. 2035 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 2036 Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : 2037 Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: 2038 With Chlorpyriphos/Lindane E.C. 20% with 1% concentration 2039 Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5km also includingramming and watering of the earth in layers not exceeding 20cm in trenches, plinth, sides of foundation etc. complete. 2040 CONCRETE WORK 2041 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2042 1:5:10 (1 Cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size) 2043 Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : 2044 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). 2045 Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size) 2046 Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil. 2047 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 2048 REINFORCEDCEMENTCONCRETE 2049 Centering and shuttering including strutting, propping etc. and removal of form for all heights: 2050 Foundations, footings, bases of columns, etc. for mass concrete 2051 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc 2052 Columns, Pillars, Piers, Abutments, Posts and Struts 2053 Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 2054 Edges of slabs and breaks in floors and walls 2055 Under 20 cms wide 2056 Suspended floors, roofs, landings, balconies and access platform. 2057 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 2058 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 2059 50 mm thick 2060 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2061 Thermo-Mechanically Treated bars of grade Fe-500D or more. 2062 Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. 2063 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). 2064 All works upto plinth level 2065 All works above plinth level upto floor V level 2066 Add for using extra cement in the items of design mix over and above the specified cement content therein. 2067 BRICK WORK 2068 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2069 Cement mortar 1:6 (1 cement : 6 coarse sand) 2070 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately). 2071 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. 2072 Cement mortar 1:4 (1 cement :4 coarse sand) 2073 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. 2074 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). 2075 MARBLE WORK 2076 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 2077 Granite of any colour and shade 2078 Area of slab over 0.50 sqm 2079 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. 2080 Granite work 2081 Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete. 2082 Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. 2083 WOOD WORK & PVC WORK 2084 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). 2085 Second class teak wood 2086 Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). 2087 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 2088 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws 2089 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 2090 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 2091 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). 2092 Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws : 2093 35 mm thick shutters 2094 Kiln seasoned and chemically treated hollock wood 2095 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. 2096 Fixed to steel windows by welding 2097 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. 2098 With 12 mm mild steel U beading 2099 Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete. 2100 250 mm weighing not less than 150 gms 2101 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 2102 250x16 mm 2103 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 2104 200x10 mm 2105 Providing and fixing aluminium handles, ISI marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868) transparent or dyedto required colour or shade, with necessary screws etc. complete : 2106 125 mm 2107 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 2108 Twin rubber stopper 2109 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 2110 1.5 mm thick 2111 Providing and fixing Pre-laminated flat pressed 3 layer (medium density)particle board or graded wood particle board IS : 3087 marked, with oneside decorative and other side balancing lamination Grade I, Type IIexterior grade IS : 12823 marked, in shelves with screws and fittingswherever required, edges to be painted with polyurethane primer (fittingsto be paid separately). 2112 18 mm thick 2113 Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 2114 Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm). 2115 Providing and fixing ISI marked oxidised M.S. single acting spring hingeswith necessary screws etc. complete : 2116 150 mm 2117 Providing and fixing oxidised M.S. hasp and staple (safety type)conforming to IS : 363 with necessary screws etc. complete : 2118 90 mm 2119 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 2120 75 mm 2121 Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood. 2122 50x50 mm (base and height) 2123 Float glass panes 2124 4 mm thick glass pane (weight not less than 10kg/sqm). 2125 STEEL WORK 2126 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 2127 Using M.S. angles 40x40x6 mm for diagonal braces 2128 Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment). 2129 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 2130 Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. 2131 Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 2132 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing. 2133 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. 2134 M.S. tube 2135 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 2136 4.0 mm thick glass panes 2137 FLOORING 2138 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 2139 40 mm wide and 4 mm thick 2140 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 2141 25 mm thick. 2142 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. 2143 Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab. 2144 Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre. 2145 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 2146 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigment etc., complete. 2147 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand),jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. 2148 Size of Tile 600x600 mm 2149 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. 2150 Size of Tile 400x400 mm 2151 ROOFING 2152 Providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat. 2153 With common burnt clay F.P.S. (non modular) brick tilesof class designation 10 2154 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. 2155 FINISHING 2156 12 mm cement plaster of mix 2157 1:6 (1 cement: 6 coarse sand) 2158 15 mm cement plaster on rough side of single or half brick wall of mix: 2159 1:6 (1 cement: 6 coarse sand) 2160 Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floatingcoat of neat cement. 2161 20 mm cement plaster 2162 6mm cement plaster of mix 2163 1:3 (1 cement : 3 fine sand) 2164 White washing with lime to give an even shade : 2165 New work (three or more coats) 2166 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : 2167 New work (two or more coats) over and including water thinnable priming coat with cement primer 2168 Finishing walls with Premium Acrylic Smooth exterior paint withSilicone additives of required shade: 2169 New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 2170 Applying priming coat: 2171 With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) 2172 With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works 2173 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 2174 Two or more coats on new work 2175 Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : 2176 Two or more coats on new work 2177 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2178 WATER PROOFING 2179 Providing and laying in situ seven course water proofing treatment with APP (Atactic poly-propylene) modified Polymeric memberane over roof consisting of first coat of bitumen primer @ 0.40 litre per sqm, 2nd, 4th & 6th courses of bonding material @ 1.20 Kg/sqm, which shall consist of blown type bitumen of grade 85/25 conforming to IS : 702, 3rd and 5th layers of roofing membrane APP modified Polymeric membrane 1.5 mm thick of 2.25 Kg/sqm weight consisting of five layers prefabricated with centre core as 20 micron HMHDPE film sandwiched on both sides with polymeric mix and the polymeric mix is protected on both side with 20 micron HMHDPE film. 7th, the top most layer shall be finished with brick tiles of class designation 10 grouted with cement mortar 1:3 (1cement : 3 fine sand) mixed with 2% integral water proofing compound by weight of cement over a 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat (item of laying brick tiles shall be paid for separately). 2180 Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. 2181 Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. 2182 After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. 2183 Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. 2184 The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : 2185 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: 2186 Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. 2187 IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. 2188 IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. 2189 IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/ sqm). 2190 NON SHEDULE ITEMS 2191 Providing and laying cinder filling in sunken floors and other locationswith approved quality cinder including watering and light ramming etc.required for proper compaction/completion of the work complete in all respects as per drawings and as directed by the Engineer in Charge. 2192 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 2193 150 mm 2194 Providing and fixing aluminium door buffer of approved make, design and colour with necessary screws etc all complete as directed and specified by the Engineer-in-Charge : 2195 Providing and laying 1st quality ceramic glazed Anti skid floortiles of size 300x300 mm (thickness to be specified by the manufacturer) conforming to IS:15622 in all colours, shades, sizes as approved over 20 mm thick bed of Cement Mortar 1: 4 (1 cement : 4 Coarse Sand) including pointing the joints with white cement and matching pigment etc complete in all respects as per specifications/drawings and to the entire satisfaction to the Architect. 2196 STAFF QUARTER-II (G+1)5 NosPlumbing work 2197 EARTH WORK 2198 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2199 All kinds of soil. 2200 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2201 All kinds of soil 2202 Pipes, cables etc, not exceeding 80 mm dia. 2203 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia 2204 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2205 ROOFING 2206 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2207 110 mm diameter 2208 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 2209 Coupler 2210 110 mm 2211 Bend 87.5° 2212 110 mm bend 2213 Shoe (Plain) 2214 110 mm Shoe 2215 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 2216 110 mm 2217 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams. 2218 SANITARY INSTALLATIONS 2219 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 2220 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 2221 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. 2222 W.C. pan with ISI marked white solid plastic seat and lid 2223 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: 2224 White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap 2225 Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 2226 Kitchen sink with drain board 2227 510x1040 mm bowl depth 250 mm 2228 Extra for using coloured pedestal type W.C pan (European type) with low level cistern of same colour instead of white vitreous china W.C pan and cistern. 2229 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 2230 Providing and fixing toilet paper holder : 2231 Vitreous china 2232 Providing and fixing soil, waste and vent pipes : 2233 100 mm dia. 2234 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 2235 75mm diameter 2236 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 2237 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : 2238 For 100 mm dia. pipe 2239 For 75 mm dia. pipe 2240 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 2241 100 mm 2242 Sand cast iron S&S as per IS - 3989 2243 75 mm 2244 Sand cast iron S&S as per IS- 3989 2245 Providing and fixing plain bend of required degree. 2246 100 mm 2247 Sand cast iron S&S as per IS : 3989 2248 75 mm 2249 Sand cast iron S&S as per IS - 3989 2250 Providing and fixing heel rest sanitary bend 2251 100 mmdia 2252 Sand cast iron S&S as per IS - 3989 2253 75 mm dia 2254 Sand cast iron S&S as per IS - 3989 2255 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3mm thick,bolts and nuts complete. 2256 100x100x100mm 2257 Sand cast iron S&S as per IS - 3989 2258 75x75x75mm 2259 Sand cast iron S&S as per IS - 3989 2260 Providing and fixing single equal plain junction of required degree 2261 100x100x100mm 2262 Sand cast iron S&S as per IS - 3989 2263 75x75x75mm 2264 Sand cast iron S&S as per IS - 3989 2265 Providing and fixing door piece, insertion rubber washer 3mm thick, bolts & nuts complete : 2266 100 mm 2267 Sand cast iron S&S as per IS - 3989 2268 75 mm 2269 Sand cast iron S&S as per IS - 3989 2270 Providing and fixing terminal guard : 2271 100 mm 2272 Sand cast iron S&S as per IS - 3989 2273 75 mm 2274 Sand cast iron S&S as per IS - 3989 2275 Providing and fixing collar : 2276 100 mm 2277 Sand cast iron S&S as per IS - 3989 2278 75 mm 2279 Sand cast iron S&S as per IS - 3989 2280 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 2281 100 mm 2282 75 mm 2283 Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter : 2284 100 mm 2285 75 mm 2286 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 2287 100 mm inlet and 100 mm outlet 2288 Sand Cast Iron S&S as per IS: 1729 2289 Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 2290 100 mm dia 2291 Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work : 2292 100 mm diameter pipe 2293 75 mm diameter pipe 2294 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 2295 Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms 2296 Providing and fixing PTMT Bottle Trap for Wash basin and sink. 2297 Bottle trap 31mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms 2298 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. 2299 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 2300 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. 2301 Providing and fixing G.I. pipes complete with G.I. fittings including trenching & refilling. 2302 External work 2303 32mmdia nominal bore 2304 40mmdia nominal bore 2305 50mmdia nominal bore 2306 WATER SUPPLY 2307 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 2308 Internal work - Exposed on wall 2309 25 mm nominal outer dia Pipes metre 2310 32 mm nominal outer dia Pipes metre 2311 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 2312 Concealed work, including cutting chases and making good the walls etc. 2313 15 mm nominal outer dia Pipes 2314 20 mm nominal outer dia Pipes 2315 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 2316 25 to 40 mm nominal bore 2317 Providing and fixing brass stop cock of approved quality : 2318 15 mm nominal bore 2319 20 mm nominal bore 2320 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 2321 25mm nominal bore 2322 32mm nominal bore 2323 40mm nominal bore 2324 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 2325 25 mm nominal bore 2326 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 2327 25 mm nominal bore 2328 Providing and fixing uplasticised PVC connection pipe with brass unions : 2329 45 cm length 2330 15 mm nominal bore 2331 Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 2332 100 mm diameter 2333 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 2334 Rectangular tank 2335 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 2336 15 mm nominal bore 2337 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 2338 15 mm nominal bore 2339 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 2340 15 mm nominal bore. 2341 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 2342 15 mm nominal bore 2343 Providing and fixing PTMT grating of approved quality and colour. 2344 Circular type. 2345 100 mm nominal dia. 2346 Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof. 2347 SEWARAGE & DRAINAGE 2348 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 2349 100 mm diameter 2350 150 mm diameter 2351 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 2352 100 mm diameter S.W. pipe 2353 150 mm diameter S.W. pipe 2354 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70kg as per standard design: 2355 150 x 100 mm size P type 2356 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2357 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : 2358 Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : 2359 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2360 Extra for depth for manholes : 2361 Size 90x80 cm 2362 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2363 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 2364 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 2365 For pipes 100 to 250 mm diameter 2366 Providing, laying and jointing non pressure NP2 class (light duty)RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 2367 150 mm dia RCC pipe 2368 STAFF QUARTER-II (G+1)5 NosElectrical Work 2369 SUBHEAD - I - WIRING 2370 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. 2371 Group C 2372 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. 2373 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2374 4 Module (125 mmX75 mm) 2375 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2376 15/16 A switch 2377 3 pin 5/6 A socket outlet 2378 Telephone socket outlet 2379 TV antenna socket outlet 2380 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2381 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earth wire 2382 2 X 10 sq. mm + 1 X 6 sq. mm earth wire 2383 Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. 2384 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required. 2385 25 mm 2386 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 2387 1 or 2 Module (75 mmX75 mm) 2388 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2389 2 Pair 2390 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 2391 20 mm 2392 25 mm 2393 Providing and fixing in position 2mm thick M.S. Telephone junction box of size suitable for fixing of following Krone Tag Block with key lock arrangement. Also provide clamps for fixing tag blocks. 2394 10 pair Telephone Tag Blockwith box 2395 Supplying, laying of 10 pair unarmoured PVC insulated copper conductor (ATC) telephone cable in ground/existing pipes/on wall and making connection with telephone main junction box (MDF) including supports and all accessories as required 2396 10 Pair Cable unarmoured 2397 SUBHEAD - II - SUPPLY & INSTALLATION OF FITTINGS 2398 Supplying of following box type Fl. fitting made out of CRCA sheet finished in antirust treated non-yellowing super white stove enamelled paint duly wired with copper wound heavy duty choke starter holder, starter but without lamp complete etc. as reqd. 2399 Mounting rail for TLED lamps 1600 Lumens (TMC 501 P 1xT-LED with Essential LED 18W Tube) 2400 Supplying of wall bracket light fittings suitable for 11 / 13 W CFL lamp. The fitting shall be made up of M.S. powder coated provided with integral ballast, frosted glass and 1 no. 11 / 13 Wlamp duly wired upto the connector block complete as required. (Decon Cat. No.05AAM) 2401 Supplying of ceiling light fittings suitable for 1 x 15/20 W LED lamp. The fitting shall be made up of M.S. powder coated provided with electronic ballast, 1 no. 15/20 W LED lamp duly wired upto the connector block etc. complete as required. 2402 Cirrus Mini Pro 15 / 20 watt & 1100 /1600 Lumens (Philips SM200C LED11S 6500 PSU OD WH) 2403 Supplying of bulk head fittings suitable for 10 W LED lamp complete with ballast & accessories such as glass, wire guard, 60 W CFL lamp etc. complete as required. 2404 Endural LED-Bulkhead, 10 W, 600 lumen Such as (Philips WT202W LED6S CW PSU S2 PC) 2405 Supplying of exhaustfan, all complete with mounting ring frame i/c bracket,but without regulator with shutters in the following sizes. (G.E. ALSTHOM, KHAITAN & HAVELLS COMPANY) 2406 300 mm 4 Pole 2407 Supplying of 1400 mm sweep A.C. electric Ceiling fans, capacitor type with double ball bearing complete with 300 mm down rod, canopies, shackles, blades, but without regulator suitable for operation on 230 / 240 Volts, 50 Hz, single phase, A.C. supply. (CROMPTON, KHAITAN & HAVELLS COMPANY) 2408 Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. 2409 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. 2410 Installation, testing and commissioning of pre-wired, light fixture / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. 2411 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. 2412 Upto 450 mm sweep 2413 Extra for fixing the louvers/ shutters complete with frame for a exhaust fan of all sizes. 2414 Installation, testing and commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/ LED lamps per fitting, complete with all accessories including connections etc. as required. 2415 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. 2416 SUBHEAD - III - DISTRIBUTION BOARD 2417 Supplying, installing, testing and commissioning of compartmentalised cubical type meter board for installation of single phase meter. The cubical board shall be made of 2mm thick C.R.C.A sheet, duly phosphatised powder coated complete with connection bus bar and following accessories mounted in it. 2418 METER BOARD 2419 INCOMING : 2420 40A TP MCCB having breaking capacity - 25 KA - 1 No. 2421 OUTGOING : 2422 Space for Single phase energy meter - 4 Nos. 2423 25 Amp DP MCB - 4 Nos. 2424 Supplying, installing, testing & commissioning of Single Phase Electronic Energy Meter, tested as per Electricity Boards requirement. 2425 Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 2426 12 way, SPN 2427 Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2428 40 amps 2429 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. asrequired. 2430 25 amps 2431 Supplying of XLPE insulated, PVC sheathed 1.1 KV grade Aluminium conductor heavy duty armoured cable as per IS : 7098 of size : 2432 4 x 16 sq.mm. 2433 Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required for crossing road/walls 2434 100 mm dia 2435 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. 2436 Single pole 2437 SUBHEAD - IV - EARTHING 2438 Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. 2439 Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. 2440 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. 2441 SUBHEAD - V- LIGHTNING CONDUCTOR 2442 Providing and fixing of lightning conductor finial, made of 25mm dia 300 mm long, G.I. tube, having single prong at top, with85 mm dia 6 mm thick G.I. base plate including holes etc.complete as required. 2443 Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required. 2444 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run) 2445 Fixing of copper/ G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run) 2446 Providing and fixing testing joint, made of 20 mm X 3 mm thickG.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chucknuts and spring washers etc. complete as required. 2447 Laying copper/ G.I. tape 32 mm X 6 mm from earth electrodedirectly in ground as required 2448 EARTH CUTTING AND FILLING 2449 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m,disposed earth to be levelled and neatly dressed. 2450 All kinds of soil. 2451 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth,sides of foundation etc. complete. 2452 Cartage earth filling 2453 Bitumin Road 3.5 MTR WIDE 2454 Supplying and stacking at site 2455 Good earth 2456 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. 2457 Supplying and stacking at site. 2458 90 mm to 45 mm size stone aggregate 2459 63 mm to 45 mm size stone aggregate 2460 Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density . 2461 Qty same as 63-45 mm size Stone Aggregate 2462 Qty same as 90-45 mm size Stone Aggregate 2463 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately).(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). 2464 Providing and filling in position rubberized bitumen hot sealing compound for sealing of expansion joints in roads / pavements all complete as per direction of the Engineer-in-Charge. 2465 Using grade A sealing compound conforming to IS: 1834. 2466 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2467 Qty same as Good Earth 2468 2.00 mtr. width. Pathway 2469 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 2470 All kinds of soil 2471 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. 2472 Total Excavation 2473 Qty. of PCC 1.5.10 2474 Qty of Brickwork Upto NGL 2475 Same as good Earth 2476 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level. 2477 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size). 2478 C/s for Mass Concrete 2479 Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved s;ze, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. 2480 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 2481 Excavating trenches upto 1.5 meter depth in all kind ofsoil of required width for pipes. including excavation for sockets and dressing of sides ramming of bottoms including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m or as directed at site by engg-in-charge. 2482 All kinds of soil 2483 Pipes, cables etc, not exceeding 80 mm dia. 2484 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 2485 External work 2486 32mm dia nominal bore 2487 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 2488 25 to 40 mm nominal bore 2489 making G.I connection 2490 Type-2(G) (3+5) = 8 meter 2491 Type-IV (3+5) = 8 meter 2492 Guest House (3+5) = 8 meter 2493 Boys Dormitory(G+2)= (3x3x2+5x2) = 28 meter 2494 Girls Dormitory(G+2)= (3x3x2+5x2) = 28 meter 2495 Type-3(G+1)= (3x2+5) = 11 meter 2496 Type-3(G+2)= (3x3+5) = 14 meter 2497 Type-2(G+1)= (3x2+5) = 11 meter 2498 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. 2499 40 mm dia nominal bore 2500 65mm dia nominal bore 2501 Providing and fixing gun metal non- return valve of approved quality (screwed end) : 2502 40 mm nominal bore 2503 Horizontal 2504 Construction of Masonary Chamber60x60x75 inside in Brickwork Cement Mortar 1.6 2505 With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 2506 Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 2507 50 mm dia 2508 50 mm dia 2509 100 mm dia 2510 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 2511 32 mm nominal bore 2512 32 mm nominal bore 2513 40 mm nominal bore 2514 Providing and laying in position cement concreteof specified grade excluding the cost of centering and shuttering (for thrust blocks at bends and junctions of water lines )by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size) 2515 Providing and fixing G.I. Union in GI pipe including cutting and threading the pipe and making long screws etc. complete(New work) 2516 25 mm nominal bore 2517 32 mm nominal bore 2518 40 mm nominal bore 2519 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2520 LD- 2.5 2521 Rectangular shape 600*450 mm internal dimensions 2522 EXTERNAL SEWER LINE 2523 Excavating trenches of required width for pipes, cable, etcincluding excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.50m including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m. 2524 All kinds of soil 2525 Pipes cables etc. exceeding 80 mm dia. But not exceeding 300mm dia. 2526 Pipes, cables etc. exceeding 300 mm dia but not exceeding 600 mm 2527 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 2528 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) 2529 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 2530 150 mm dia. R.C.C. pipe 2531 250 mm dia. R.C.C. pipe 2532 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2533 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size). 2534 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 2535 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1cement : 2 fine sand) including testing of joints etc. complete : 2536 300 mm dia. R.C.C. pipe 2537 450 mm dia. R.C.C. pipe 2538 Centering and shuttering including strutting, propping etc. and removal of form for : 2539 Foundations, footings, bases of columns, etc. for mass concrete. 2540 Constructing brick masonry manholein cement mortar 1 : 4 (1 cement : 4 coarse sand) with RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4gradestone aggregate 20mm nominal size); foundation concrete 1:4:8 mix(1 cement : 4 coarse sand : 8 gradedstoneaggregate40 mm nominalsize) insideplastering 12 mm thickwith cementmortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and makingchannels incementconcrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat ofneatcement completeasper standard design 2541 Inside size 90 x 80 cm & 45 cmdeep including CI cover with frame (light duty) 455 x 610mm internal dimensions, total weight of cover & frame to be not lessthan 38 kg (weight of cover 23 kg and weight of frame 15 kg) 2542 With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 2543 Inside size 120 x 90 cm & 90 cmdeep including CI cover with frame (Medium duty) 560mm internal diameter, total wt. of cover & frame to be not lessthan 208 kg (wt. of cover 108 kg and wt. of frame 100 kg) 2544 With common burnt clay F.P.S.(non modular) bricks of classic designation 7.5 2545 Extra for depth for manholes: 2546 size 90 X 80 cm 2547 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2548 size 120 X 90 cm 2549 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2550 Providing and fixing square mouthS. W. Gully trapclass SP-1 complete with C.I. gratingbrickmasonry chamber with water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 2551 180 x 150 mm. size P type 2552 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2553 Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2554 Circular Manhole Internal dia 0.91mtr. 2555 Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2556 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : 2557 With Sewer bricks conforming IS : 4885 2558 Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m : 2559 12 mm cement plaster of mix: 2560 1:4 (1 cement: 4 fine sand) 2561 Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2562 2.30 m deep with SFRC Cover and frame (heavy duty HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : 2563 With Sewer bricks conforming IS : 4885 2564 Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : 2565 With Sewer bricks conforming IS : 4885 2566 12 mmcement plaster of mix 2567 1:4 (1 cement : 4 coarse sand). 2568 Providing M.S. foot restsOrange colour Safety footrest 2569 With 20x20 mm square bar 2570 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 2571 Drain (230mm x 300mm) 2572 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2573 All kinds of soil. 2574 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (40% of Item No. 1) 2575 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2576 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 2577 Total 2578 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). 2579 Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: 2580 Cement mortar 1:6 (1 cement : 6 coarse sand) 2581 12 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 2582 1:4 (1 cement: 4 fine sand) 2583 Drain (300mm x 450mm) 2584 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2585 All kinds of soil. 2586 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (40% of Item No. 1) 2587 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2588 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) 2589 Total 2590 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). 2591 Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: 2592 Cement mortar 1:6 (1 cement : 6 coarse sand) 2593 12 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 2594 1:4 (1 cement: 4 fine sand) 2595 H.T./L.T. PANEL & FEEDER PILLARS 2596 SUB FEEDER PANEL 2597 Incoming 2598 MCCB 200A 35KA TPN 2599 INDICATION LIGHT 2600 BUS-BAR FEEDERS 2601 200AMP ALU.BUS-BAR TPN 2602 Out going 2603 G/D Phase-B MCCB 125A 35KA TPN 2604 B/D Phase-B MCCB 125A 35KA TPN 2605 Type 3 (G+1) MCCB 63A 35KA TPN 2606 Type 5 MCCB 32A 35KA TPN 2607 Guest House MCCB 32A 35KA TPN 2608 Type 3 (G+2) MCCB 63A 35KA TPN 2609 Type 2 (G+2) MCCB 63A 35KA TPN 2610 Spare 2611 Emergency Section 2612 Incoming 2613 MCB 125A 63KA TPN 2614 Out going 2615 B/D Phase-B MCB 63A 35KA DP 2616 G/D Phase-B MCB 63A 35KA DP 2617 Type 3 (G+1) MCB 32A 35KA DP 2618 Type 5 MCB 32A 35KA DP 2619 Guest House MCB 32A 35KA DP 2620 Type 3 (G+2) MCCB 32A 35KA DP 2621 Type 2 (G+1) MCCB 32A 35KA DP 2622 Type 2 (G) MCCB 32A 35KA DP 2623 Spare 2624 ENCLOSURE 2625 PANEL BODY FABRICATED IN 14/16 SWG CRCA SHEET , POWDER COA- TED IN SIEMENCE GREY COLOUR COMPLETE IN ALL RESPECTS UNIVERSAL GLAND PLATES. 2626 BOYS/GIRLS DORMITORY PANEL 2627 Incoming 2628 100Amp MCCB TP 35 KA 2629 Indication light R,Y,B 2630 BUS-BAR FEEDERS 2631 150Amp Aluminum bus-bar TPN 2632 Out going 2633 63Amp MCB TPN 10KA 2634 63Amp MCB TPN 10KA (SPARE) 2635 Emergency Section 2636 Incoming 2637 63Amp MCB DP 10KA 2638 Out going 2639 25Amp MCB DP 10KA 2640 32Amp MCB DP 10KA 2641 ENCLOSURE 2642 1050*1450*150 (17 SFT) 2643 PANEL BODY FABRICATED IN 14/16 SWG CRCA SHEET , POWDER COA- TED IN SIEMENCE GREY COLOUR COMPLETE IN ALL RESPECTS UNIVERSAL GLAND PLATES. 2644 VICE PRINCIPAL HOUSE PANEL 2645 Incoming 2646 63Amp MCB TPN 10KA 2647 Indication light R,Y,B 2648 BUS-BAR FEEDERS 2649 100Amp Aluminum bus-bar TPN 2650 Out going 2651 16-32Amp MCB 12SP 10KA 2652 32Amp MCB DP 10KA 2653 space for 3 PHASE METER 2654 Emergency Section 2655 Incoming 2656 32Amp MCB DP 10KA 2657 16Amp MCB DP 10KA 2658 16AMP MCB SP 2659 ENCLOSURE 2660 650*500*150 (4SFT) 2661 PANEL BODY FABRICATED IN 14/16 SWG CRCA SHEET , POWDER COA- TED IN SIEMENCE GREY COLOUR COMPLETE IN ALL RESPECTS UNIVERSAL GLAND PLATES. 2662 METER PANEL (TYPE 2 /Type3 /GUEST HOUSE) 2663 Incoming 2664 MCB 32A 10 KA TPN 2665 Indication light R,Y,B 2666 BUS-BAR FEEDERS 2667 100AMP ALU.BUS-BAR TPN 2668 Out going 2669 Single Phase Energy Meter 2670 MCB 25A DP 2671 Emergency Section 2672 Incoming 2673 MCCB 32A DP 2674 Out going 2675 16A DP 2676 ENCLOSURE 2677 PANEL BODY FABRICATED IN 14/16 SWG CRCA SHEET , POWDER COA- TED IN SIEMENCE GREY COLOUR COMPLETE IN ALL RESPECTS UNIVERSAL GLAND PLATES. 2678 Supply installation, testing and commissioning of external post top lantern with following and complete as required. 2679 6m high (5.0m above ground) 65mm dia GI pole as approved, adopting socket at top for fixture mentioned below, base plate 300x300x6mm and provision for mounting junction box etc.- 1 set 2680 Erection of Pole in cement concrete 400x400x1000mm deep 1:3:6 ratio cement concrete foundation including excavation , refilling, secured with holding clamps, bolts, nuts, alighnment of poles casting etc. including 100 mm thick lean concrete shall be provided at the bottom. 2681 LED type 50 Watt (Street Light) light fittings of all types with allaccessories. 2682 Suitable size Control box with 1 no. incoming and 2 nos. outgoing terminals and 2 nos. tap-out terminal with 1 no.5A HRC fuses complet 1 set 2683 Suitable number (S) 40mm dia Class-B GI Pipes(s) from above control box to upto 0.5 meter below ground level for power cable entry. 2684 LT CABLES 2685 Supply of following size of 1.1 KV grade multicore aluminium cunductor PVC sheathed armoured cable as per IS 1554. 2686 4 Core 25 Sqmm 2687 4 Core 16 Sqmm 2688 3.5 Core 240 Sqmm 2689 3.5 Core 95 Sqmm 2690 2 Core 120 Sqmm 2691 2 Core 50 Sqmm 2692 2 Core 16 Sqmm 2693 2 Core 10 Sqmm 2694 G.I. Earth pipe electrode with salt/charcoal: 2695 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 2696 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. 2697 EarthingwithGI earth pipe 4.50 meter long 40mm dia including accessories, and providing masonry enclosure with cover plate having lockingarrangement and watering pipe etc.with charcoal or coke and salt complete as required. 2698 EarthingwithGI earth plate 600 x 600 x 3mmthickincluding accessories, and providing masonry enclosure with cover plate having lockingarrangement and watering pipe etc.ith watering pipeof 2.7 meter long etc. with charcoal or coke and salt complete as required. (for MLTP & DG body) 2699 Providing and fixing 25 mm x 5 mm copper strips in 40 mm dia G.I.pipe from earth electrode, including connection with brass nut bolts , spring washer, excavation and refilling etc, as required ( copper plate earthing) 2700 Providing and fixing 25 mm x 5 mm GI strip in 40 mm dia G.I.pipe from earth electrode, including connection with brass nut bolts , spring washer, excavation and refilling etc, as required ( copper GI plate earthing) 2701 Providing& layingearth connection from earth electrode with 6 SWG dia GIwire in 15 mm Gi pipe from earth electrode including connection with GI thimbleexcavation and refilling etc as required. ( for GI pipe earthing ofpoles) 2702 Supply & Laying of 25 x 5 mm copper earth strip in surface /recess 2703 Providing and fixing 25mm x 5 mm G.I. strips on surface or in recess for connections etc. as required 2704 Providing andfixing MVdanger noticeplate of200 mm x 150 mm madeofmild steelatleast 2 mm thickandvitreousenameled white on both sides & with inscription in signalred colour on front side as required.( on 7mts poles & panels) 2705 LT CABLES LAYING 2706 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. 2707 Upto 35 sq. mm 2708 Above 35 sq. mm and upto 95 sq. mm 2709 Above 95 sq. mm and upto 185 sq. mm 2710 Above 185 sq. mm and upto 400 sq. mm 2711 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 2712 63 mm dia (OD-63 mm & ID-51 mm nominal) 2713 120 mm dia (OD-120 mm & ID-103 mm nominal) 2714 160 mm dia (OD-160 mm & ID-135 mm nominal)Sqmm 2715 200 mm dia (OD-200 mm & ID-175 mm nominal) 2716 Supplying and making end termination with brass comperession gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium conductor cable of 1.1 KV grade as required 2717 4 Core 25 Sqmm 2718 4 Core 16 Sqmm 2719 3.5 Core 240 Sqmm 2720 3.5 Core 95 Sqmm 2721 2 Core 50 Sqmm 2722 2 Core 16 Sqmm 2723 2 Core 10 Sqmm 2724 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 2725 Ordinary rock 2726 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. 2727 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 2728 150 mm dia. R.C.C. pipe 2729 RCC SEPTIC TANK 20 USERS 2730 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2731 All kinds of soil.0.00-1.50m 2732 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2733 All kinds of soil.1.50-3.00m 2734 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2735 All kinds of soil.3.00-4.50m 2736 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 2737 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2738 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). 2739 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing andreinforcement - All work up to plinth level : 2740 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) 2741 Centering and shuttering including strutting, propping etc. and removal of form for: 2742 Foundations, footings, bases of columns, etc. for mass concrete. 2743 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 2744 Suspended floors, roofs, landings, balconies and access platform. 2745 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 2746 Edges of slabs and breaks in floors and walls. 2747 Under 20 cm wide 2748 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. 2749 Thermo-Mechanically Treated bars. 2750 Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: 2751 Cement mortar 1:6 (1 cement :6 coarse sand) 2752 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete 2753 40 mm thick with 20 mm nominal size stone aggregate 2754 6 mm cement plaster of mix : 2755 1:3 (1 cement : 3 fine sand) 2756 6 mm cement plaster 1:3 (1 cement: 3 fine sand) finished with a floating coat of neat cement and thick coat of Lime wash on top of walls when dry for bearing of R.C.C. slabs and beams. 2757 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2758 M D - 10 2759 Square shape 450 mm internal dimension 2760 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 2761 Providing and fixing soil, waste and vent pipes 2762 100 mm dia. 2763 Centrifugally cast (spun) iron socketed pipe as per IS: 3989. 2764 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 2765 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2766 SEPTIC TANK 100 USERS 2767 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2768 All kinds of soil.0.00-1.50m 2769 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2770 All kinds of soil.1.50-3.00m 2771 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 2772 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2773 1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm nominal size). 2774 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 2775 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 2776 Centering and shuttering including strutting, propping etc. and removal of form for: 2777 Foundations, footings, bases of columns, etc. for mass concrete. 2778 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 2779 Suspended floors, roofs, landings, balconies and access platform. 2780 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 2781 Edges of slabs and breaks in floors and walls. 2782 Under 20 cm wide 2783 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. 2784 Thermo-Mechanically Treated bars. 2785 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete. 2786 40 mm thick with 20 mm nominal size stone aggregate 2787 6 mm cement plaster of mix : 2788 1:3 (1 cement : 3 fine sand) 2789 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2790 HD-20 2791 Circular shape 560 mm internal diameter 2792 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 2793 Providing and fixing soil, waste and vent pipes 2794 100 mm dia. 2795 Centrifugally cast (spun) iron socketed pipe as per IS: 3989. 2796 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 2797 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2798 RCC SEPTIC TANK 150 USERS 2799 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2800 All kinds of soil.0.00-1.50m 2801 Earth work in excavation by mechanical means (Hydraulic excavator) I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2802 All kinds of soil.1.50-3.00m 2803 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. 2804 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2805 1:5:10 (1 Cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size). 2806 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 2807 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) 2808 Centering and shuttering including strutting, propping etc. and removal of form for: 2809 Foundations, footings, bases of columns, etc. for mass concrete. 2810 Suspended floors, roofs, landings, balconies and access platform. with water proof ply 12mm thick. 2811 Lintels, beams, plinth beams, girders, bressumers and cantilevers. with water proof ply 12 mm thick 2812 Edges of slabs and breaks in floors and walls. 2813 Under 20 cm wide 2814 Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. 2815 Thermo-Mechanically Treated bars. 2816 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, includingcement slurry, but excluding the cost of nosing of steps etc. complete. 2817 40 mm thick with 20 mm nominal size stone aggregate 2818 6 mm cement plaster of mix : 2819 1:3 (1 cement : 3 fine sand) 2820 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2821 HD-20 2822 Circular shape 560 mm internal diameter 2823 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design. 2824 Providing and fixing soil, waste and vent pipes 2825 100 mm dia. 2826 Centrifugally cast (spun) iron socketed pipe as per IS: 3989. 2827 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 2828 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 2829 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2830 All kinds of soil 2831 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. 2832 All kinds of soil. 2833 1.50 mtr to 3.00mtr 2834 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. 2835 All kinds of soil. 2836 3.00mtr to 4.50mtr 2837 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. 2838 All kinds of soil. 2839 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2840 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 2841 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2842 Cement mortar 1:6 (1 cement : 6 coarse sand) 2843 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 2844 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2845 Thermo-Mechanically Treated bars of grade Fe-500D or more. 2846 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform 2847 Edges of slabs and breaks in floors and walls 2848 Under 20 cm wide 2849 12 mm cement plaster of mix : 2850 1:6 (1 cement: 6 coarse sand) 2851 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2852 H D - 20 2853 Circular shape 560 mm internal diameter 2854 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 2855 All types of soil 2856 300 mm dia 2857 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 2858 150 mm nominal size dia 2859 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2860 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 2861 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -incharge. 2862 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. 2863 DESILTING CHAMBER 2864 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2865 All kinds of soil 2866 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. 2867 All kinds of soil. 2868 1.50 mtr to 3.00mtr 2869 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. 2870 All kinds of soil. 2871 3.00mtr to 4.50mtr 2872 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 2873 1:5:10 (1 cement : 5 coarse sand(zone-III) : 10 graded stone aggregate 40 mm nominal size) 2874 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: 2875 Cement mortar 1:6 (1 cement : 6 coarse sand) 2876 Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). 2877 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 2878 Thermo-Mechanically Treated bars of grade Fe-500D or more. 2879 Centering and shuttering including strutting, propping etc. and removal of form for all heights : Suspended floors, roofs, landings, balconies and access platform 2880 Edges of slabs and breaks in floors and walls 2881 Under 20 cm wide 2882 12 mm cement plaster of mix : 2883 1:6 (1 cement: 6 coarse sand) 2884 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) as per standard design : 2885 With 20x20 mm square bar 2886 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality 2887 LD- 2.5 2888 Rectangular shape 600x450mm internal dimensions 2889 Construction brick masonry inspection chamber 60x60x60cm with bricks of class designation 75 in cement mortar 1:6 (1 cement : 6 coarse sand) including C.I Cover with frame Light weight complete as per design with FPS bricks.