BRR : 7653986 Online Notice Inviting Tender For Renovation And Beautification Work Of Bhabanipur Gramin Outlet Of Wbkvib Civil And Electrical Work During The Year 2025 26- 1 Spot application for insecticides using Aqua basespray for pest (for bugs, cockroaches, silverfish,spider, termites, mosquitoes) to walls and ceiling etc. with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying the emulsified chemical @ 0.5 litres per sq.m. by a hand operated pressure pump on wall surfaces, ceiling, electrical fixture,electrical lines including drilling holes inplaces where source of termite is detected squirting chemical solution into the holes and sealing the holes with cement grout. (Rate is per sq.m. of the floor area while actual work will be all walls ceiling, rack, partition and furniture). 2 Anti-termite treatment to the junction of wood work and masonry walls with chemical emulsion by admixing chloropyrofos emulsifiable concentrates (1% concentration) with water by weight including spraying at the points of contact with the adjoining masonry by drilling 6m. dia holes at a downward angle of about 45 degree at the junction of woodwork and masonry and squirting chemical emulsion into these holes at the rate of half litre per hole. The entire work is to be carried out as per specification of Code I.S.-6313 (Part-III)-1981. The shutters are to be sprayed with emulsion. on both sides. All wooden fixtures like almirahs, racks etc. are also to be throughly sprayed with chemical emulsion.(Payment will be made on the basis of outside measurements of doors and windows) 3 Supplying, fitting & fixing granite tiles 10mm to 12mm. thick in columns, wall, facia etc. with 15 thick [avg] cement mortar (1:2) including making suitable arrangements to hold the stones properly by brass / copper hooks including pointing in cement mortar (1:2) (1 white cement : 2 marble dust) with admixture of pigment matching the stone shades all complete as per direction of the Engineer-in-charge including cost of allmaterials, labours, scaffolding, staging ,curing and roughening of concrete surface complete.[Using cement slurry at back side of tiles@ 4.4 kg/sq.m & white cement slurry for joint filling @ 1.8 kg/sq.m] 4 Supplying,fitting & fixing in position suspended false ceiling with frame work of aluminium hollow section of size 50mm X 25mm (2.0mm thickness) combined with aluminium corners of size 38mm X 25mm, suspended by aluminium hollow tube section of size 38mm X 25mm having size of 600mm X 600mm ceiling with aluminium composit panels (ACP) - Interior grade of thickness 3.0mm comprising of proctective film, polyester coating, primer, aluminium coil, adhesive film, polyethylene core again with one layer adhesive film, aluminium bottom coating and finally service coating as per manufacturers specification finished with aluminium screw and silicon sealent complete in all respect including allincidental charges etc. as per direction of Engineer-in-charge 5 Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping] Ground Floor(vi) 19mm 6 (iv) 12mm 7 (ii) 6mm 8 Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge. The rate includes the cost of labour, adhesive and all incidental charges thereof.Glossy/Matt/Suede excluding surface texture or metallic lustre.(i) Thickness of laminate 1.5mmGround Floor 9 Supplying & laying of approved brand of scratch proof, semi flexible P.V.C. blended homogeneous marble Vinyle flooring in tiles conforming to IS:3461, fixing with syntheticacrylic adhesive after preparing the floor, levelling & smothaning when necessary with suitable putty, as per the design & instruction of the Engineer-in-charge.2 mm thick 10 Scantling upto 50mm wide and 12mm thick (chamfering or rounding) for ceiling/partion battens including fitting, fixing in position with washers, coach screws etc. complete.: (a) Ordinary teakGround Floor 11 French polishing to wood work including preparing surface (ordinary gloss)(a) On new wood work 12 Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.i) 4mm thick clear glass. 13 Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. (iv) 75mm. X 47mm. X 1.70mm. 14 Anodised aluminium barrel/ tower/ socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws:(iii) 100mm long x 10mm dia. bolt. 15 Anodised aliminium D-type handle of approved quality manufactured from extruded section conforming to I.S. specification (I.S. 230/72) fitted and fixed complete: (a) With continuous plate base (Hexagonal/ Round rod) (ii) 100 mm grip x 10 mm dia rod. 16 Supplying, fitting and fixing Godrej Multi Lock or equivallent 17 Labour for taking out rolling shutter (only shutter portion) dismantling by parts for repair or (replacement of damaged parts only), rehanging and refitting the same in position after necessary repairs (excluding the cost of supply of new parts). 18 Renewing seam pipe for rolling shutter as per existing size and shape fitting, fixing complete. 19 Oiling and greasing of rolling shutter and repair to in side lock. 20 Renewing profile of rolling shutter including fitting fixing complete as per existing size and shape. 21 Acrylic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturers specification) including cleaning and smoothning of surface.Two Coats 22 Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) :(Two coats) ii) Luxury Quality 23 Painting with ready mixed red lead paint of approved make and brand : (b) Two coats . 24 Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (a) On timber or plastered surface : With other than hi- gloss -(iv) Two coats (with any shade except white) 25 Providing and fixing exterior quality Aluminium Composite Panel (ACP) wall cladding on existing Al. /MS frame work with GI brackets, ACP fixed on the existing frame work by folding the edges of ACP panel (Engraving the rear surface of ACP sheet) with CP angles, cleats and strainless Steel screws forming groves at the periphery of ACP panel. Such grooves filled with foam and silicon sealant etc. complete with all materials (but including the cost of silicon sealant), labour, scaffolding and all other incidental charges complete in all respect as per specification and direction of Engineer-in-charge. (Mode of payment is on finished surface area of ACP) (a) 3mm thick (0.25mm Al.+2.5mm LDPE +0.25mm Al. PVDF coating) 26 Removal of rubbish,earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge 27 Supplying and fixing 240/415V MCB Isolatoro ndin rail of existing DBs and necessary connection. Havells - 63A-DP 28 Supplying and fixing 240/415V MCB of Breakingcapacity 10kA & characteristics on din rail ofexisting DBs and necessary connectionHavells - 6-32A - SP 29 Havells - 6-32A - DP 30 Supplying and fixing MCBSS enclosure with IP-20/30protection, powder coated provision for two/four poleMCB, concealed in wall after cutting the wall & mendinggood the damages to original finish incl. painting,connection& provision for earthing attachment 4 Way 31 Supplying and fixing double-door SPN MCB DistributionBoard with IP-42/43 protection, concealed inwall aftercutting the wall & mending good the damages tooriginal finishincl. Interconnection with suitable size ofcopper wire and neutral link & provision for earthing attachment Havells - 2+16 way -Enclosure (DHDPSNODRW16) 32 Supply & Fixing EI danger board on wall(a) 15 cm x 10 cm (6x4) 33 Distribution wiring in 1.1KV grade 2x22/0.3 (1.5sqmm)singlecore stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) insuitable size PVC casing-capping (Precision make) with 1x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unshea the copper wire for ECC, incl. necy. fittings etc. to light/fan/call bell point with Modular type switch (Brand approved by EIC) fixed on Modular GI /PVC switch board with top cover plate on wall incl.mending good damage stoorig in all finish. [PVC casing capping and Switch board both on surface]Average run 8 mtr 34 Distribution Wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire (Brand approved by EIC) in suitable size PVC casing-capping (Precision make) with 1x22/0.3 (1.5 sqmm) single core stranded FR PVC insulated & unsheathed copper wire for ECC, incl. necy. fittings etc. with S & F 6A 5 pin Modular type plug socket and switch (Brand approved by EIC) fixed on 4 Module GI / PVC switch board with 3/4 Module top cover plate on wall incl. necy. connection making earthing attachment, painting and mending good damages to building works [PVC casing-capping and plug box both on surface]Average run 7.5 mtr 35 Supply of LED Tube Light 1200 mm, Havells-LED Pride Plus NXT Batten 40 W 6500 K -LHEXAPP7IN1W040or Similar Make 36 Fixing only bulk head ceiling fitting on wall /ceiling by screws etc. 37 Supply of LED Track Light Havells -LED Streek Track Light 7 W 3000 K BLK -LHEEANPBPH1K007or Similar Make 38 Fixing only bulk head ceiling fitting on wall /ceiling by screws etc. 39 Supply of LED Pannel Celing LightHavells -TRIM PLUS LED PANEL SQUARE -12 W LED 4000 K -LHEBGAP6IZ1W012or Similar Make 40 Fixing only bulk head ceiling fitting on wall /ceiling by screws etc. 41 Supply of Wall Mount Swing FanHavells -Swing HS Off-White - FHWSWHSOWH12or Similar Make 42 Fixing only cabin fan on wall/ceiling by S&F rag bolts, nuts & washers (6 mm dia x 62 mm long) or as reqd. incl. S&F 24/0.20 PVC insulated flexible copper wire 0.5 mt. length 43 Scissors (For Fabric Cutting) 44 Scale 45 Wooden Scale (For Fabric Measurement) 46 PVC Hanger 47 Browser Stand (For Product Display) 48 PVC Chair 49 Compact Desktop CPU with i3 12GEN DDR4 8GB 512-SSD with 20 moniter (HP Model -S01-pF2567in) 50 Barcode Scanner (TVS Model - L100 plus) 51 Scanner with printer (HP Model -126a) 52 UPS (Zebronics Model-ZEB-U750) 53 Keyboard + Mouse (Dell) 54 64 GB Pen drive - (Sandisk) 55 CCTV Bullet Camera Dahua make 2MP DH-HAC-HFW1220 RP 56 8 CH Dahua make DVR Machine with Networking system Model-DH-XVR4A08 57 2 TB Sata HDD AV-DRIVE WD make 58 Power supply (SMPS) 10A 12V Dahua make DH-PFM3215-120-IN 59 Monitor 18 Dahua Make DHI-LM18-B200 60 D-Link Copper 3+1 CCTV Cable with Laying P/Mtr 61 Supply & Fixing special type of imported solid acrylic letter (Thickness 3mm raised, 1.5 inch above ACP sheet. All side each letter glows or emits light uniformly. Calculation based on aa dimension at over Store entrnce gate of different Khadi Gramin Store at different place

BRR : 8668933 Tender For Additional / Alternator To Open Shed At Gt Ground Gandhinagar Under Ge (Af) Chiloda; 1 M&L Brickwork with subclass ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed. 2 M&L for formwork to sides and soffits of floor or roof beam, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves inluding supports, overhangs etc also splays between floor and beams etc,flat & rough finished surface of concrete complete all as specified and directed. 3 S&F Reinforcement steel (TMT Bar)10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 4 S&F Reinforcement steel (TMT Bar) 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. 5 M&L Reinforced Cement concrete (nominal mix) Type B1 1:2:4 (using 20 mm graded aggregate) for Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specfied and directed. 6 Taking down cement plaster on brick or PCC block masonry wall in any description complete all as specified and directed. 7 M&L for rendering 10mm thick on fair faces of brick/concrete surface in CM (1:6) finished even and smooth without using extra cement complete all as specified and directed.. 8 M&L for rendering to ceiling in 5mm thick on fair faces concrete surface in CM (1:3) finished even and smooth without using extra cement complete all as specified and directed. 9 M&L for rendering 15mm thick plaster in CM 1:4 on fair faces of brick work or concrete surfaces of walls finished even & smooth with out using extra cement complete all as specified and directed. 10 M&L for oil bound distempering two coats over a coat of alkali resistant priming paint including preparation of newplastered surfaces of wall complete all as specified and directed by Engineer - in -Charge.Note : All work to be operated by mechanically (i.e Grinder Machine and Air less painting machine) not by blade / brush / roller / normal spray machine) 11 All as per Item No 10 here in before but on ceiling complete all as specified and directed. Note : All work to be operated by mechanically (i.e Grinder Machine and Air less painting machine) not by blade / brush / roller / normal spray machine) 12 Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfacescomplete all as specified and directed.Note : All work to be operated by mechanically (i.e Grinder Machine and Air less painting machine) not by blade / brush / roller / normal spray machine) 13 Providing and fixing factory made uPVC white colour casement (Openable) Door made of extruded profile wilh wall thickness of 2.3mm ( + -0.2mm). Window profile with hollow section with mitlti chamber, frame (60mm x 58mm), sash (60mm x 78mm). T profile (One vertical length in between two shutters) (60mm x 74mm). Glazing bead (35mm x 20mm) will be mitered cut and fusion welded at all corners, including drilling ol holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket 1.2 + -0.2mm thick galvanized steel Frame (28mm x 21.5mm), sash (31mm x 27mm), T profile (27mm x 17mm) to be inserted in required profile, frame will be fixed to the wall wilh 8mm x 100mm long fasteners. Hardware: [casement door handle made of zinc alloyed (white powder coated). Corner striker. Secondary Strikers. Cylinder. Door transmission gear made of mild sleel with multi point locking system with strikes. 3D Hinges of zinc alloyed (white powder coated) [and 5mm thick glazing with selected quality glass complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and will be measured and paid separately and includes all other connected accessories like Lock etc. Net opening will be measured for payment purpose.) 14 Supply & Fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed. 15 Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 16 Supply only6 mm thick sheet figured glassand glazing with rubber packing around the glass, in squaresn exceeding 0.50 sqm in each pane complete all as specified and directed. 17 Demolition Cement concrete(unreinforced) Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. 18 M&L 50mm average thickness PCC 1:2:4 type B0 using 12.5mm graded aggregate as in padding and (roof levelling course) on roof surfaces complete all as specified. Note- Water proofing compound to be used @ 3% by weight of cement content for concrete padding work and will be measured and paid separately. 19 M&L for rendering in CM (1:3) 10mm thick over RCC roof, chajja/ brick wallmixed with water proofing compound @ 3% by weight of cement finished even and fair without using extra cement complete all as specified and directed. Note - WPC shall be measured and paid separately. 20 M & Lin repairsfor roof treatmentwith following specification completely, complete all as specified and as directed by Engineer-in-Charge :-(i)Applying a coat of hot bitumen 85x25 @ 1.2kg per sqm.(ii)Laying 3mm thickness APP modified membrane weighting not less than 3 to 4 kg/sqm in 100 mm over laps both longitudinally and transversally and overlaps to be sealed by torch, membrane shall be taken upto the thickness of slab/front fascia. 21 M&L for 75mm thick Cement concrete Type D21:2:4 (40 mm graded gradedaggregate) as in floor finishes and pavings as base complete all as specified and directed. 22 M & L for Virified Dark Shade / Double Charged / Ultracharged tiles Tiles 10mm thick, polished, of size exceeding 0.42 Sq.m and not exceeding 1 Sq.m, [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed. 23 All as per item No 22 here in before, but on vertical surfaces incl 10mm thick CM 1:3 as in baking coat of dado/skirting complete all as specified and directed. 24 M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. 25 M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection and finished even and smooth with using extra cementcomplete all as specified and directed. 26 Supply & fixing in repair with semi perforated 12mm thick micro tegular edged GRG false tiles at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module of s1ze 600x 600mm , suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1 OOOmm length and L shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in Charge. 27 Demolition Cement concrete(unreinforced) Concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.. 28 M&L for 75mm thick Cement concrete Type D21:4:8 (40 mm graded gradedaggregate) as in floor finishes and pavings complete all as specified and directed. 29 Dismantlingof stone slabs and paver block tiles of any description or thickness in floorslaid bedded and pointed in any mortar complete all as specified and directed. 30 M&L Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. 31 M&L for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS-15658-2006 of 60mm thickness M-35 gradecomplete all as specified and directed. 32 All as per item No 31 here in before but except tiles. 33 M& L factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever complete all as specified and as directed. 34 M&L for preparation of old painted surfaces of wall / concrete surfacesover 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed. 35 Taking down carefully copper/ aluminum point wiring (Light, fan, socket, power and Bell) including fixture and fittings such as switches, sockets, ceiling roses, lamp, holder , regulators, socketslight fittings etc , removing material to store for keeping in safe custody or for taking credit , and making good disturbed surface of walls, floors, etc. complete all as specified and as directed. 36 M&L forpoint wiring with 1.5 Sqmm single core PVC insulated unsheathed multi stranded copper conductor FRLSH cable 1100V grade drawn through and incl PVC concelled conduit with accessories like bends tees, junction boxes etc fixed recessed in wall or ceiling etc including 1.5 Sqmm single core PVC insulated but unsheathed multistrandard copper conductor FRLSH cable 1100V grade as earth continuity wire incl modular sunken type pressed steel terminal boxes of size with 3mm thick bakelite steel white/coloured top cover for the following:- 37 (a) One light pointcontrolled by one switch complete all as specified and as directed. 38 (b) One fan point controlled by one switchcomplete all as specified and as directed. 39 All as per item No 36 here in before but with cable of size 2.5 Sq mm PVC insulated on independent boardfor power plug 15 Amps complete all as specified and as directed. 40 Supply and fixing Modular switch one way 6A,1 Module, complete all as specified and directed. 41 Supply and fixing Modular switch one way 16A,1 Module, complete all as specified and directed. 42 Supply and fixing Modular socket 16/15A-2/3 pin combined2 Module complete all as specified and directed. 43 Supply and fixingModular Fan Regulator, 120W, 2 module complete all as specified and directed. 44 Supply & fix ceiling rose 3 terminal/ poly carbonate, isolated body complete all as specified and directed. 45 M&L for concealed sub main wiring complete with PVC insulated FRLSH cable of single core 4 Sqmm 1100 volts grade with multi standard copper conductor for drawn through and including conduiting PVCConduit with accessories incl 4 Sqmm unsheathed multi standard FRLSH copper conductor as earth wire. Note: Two runs of cable and one run of conduit & earth wire shall be measured as one run length complete all as specified and as directed. 46 Supply and fixing Supply and fixing LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed type with highefficiency PMMA diffuser soft glare free light completewith driver, holders & LED lamp suitable for roofceiling including connecting up with driver threecore flexible copper conductor cases of suitable size complete all as specified and as directed. 47 Supply and fixing LED bldg securitylight fitting 60 Watt230 V AC outdoor type with high pressure diecast aluminum hosing and heat resistantcomplete with driver, lamp bracket with impactand corrosion resistant including thermalmanagement in multiple optics complete withIP 65/66 protection, service bracket, nuts, bolts to fix the security light on wall, required length and capacity of FRLSH PVC multistranded copper conductor for electrical connection from ceiling rose to coneector of security lightcomplete all as specified and directed. 48 Taking down ceiling fan 1200mm/1400mm sweep forcomplete servicing, repair of fan motor and replacement of worn out parts such as bearing,including paintingof ceilingfan with synthetic enamel paint by spraying with filling the cavities with filler, one coat after cleaning all dust and writing the MES No and hanging of ceiling fan with new down rod of 90 cm heightin situ , complete all as specified and directed by Engr-in-Charge. 49 Supply and fix exhaust fan, steel bodyAC single Phase. 230V of size 300msweep with, blades, and frame and louvers complete all as specified and directed by Engr-in-Charge. Note :- (a)Making hole in existing brick/PCC wall of required size to accommodate exhaust fan and fixing louvers on outer surface shall be deemed to be inclusive of quoted rate by the contractor. 50 Supplying and fixing of sheet metal enclosure, single phase, double door SPN DB 8 way, flush to wall mounting for MCB fitted with 200 Amp ratedbus barsand neutral links ( without MCBs) SPN/ TPN complete all as specified and directed by Engr-in-Charge. 51 Supply and fixing240V, 10KA C curveminiature circuit breaker (MCB) of SPN 40 AMPand current carrying capacity in the MCBDB complete with connection testing and commissioning complete all as specified and directed. 52 Supply & fix MCB SP 6 to 32 Amps 10 KA 240 V, 10 KA Ç Curvecomplete all as specified and directed. 53 M & L for plastic bodyJumbo air cooler having 150 ltr water tank capacity, 5 blades, single phase 230 volts AC Supplyand mounted on wheel for easy movement complete all as specified and directed. 54 M & L for earthing complete with galvanised steel earth plate electrode of size 60 cm x 60 cm x 6mm thick burried directly in ground not less that 2.25 m deep below normal ground level and top edge of the plate not less than 1.5 mtrs below normal ground level connected to GI strip of size 25 x 4 mm by means of bolts, nuts, check nuts and washers of GI or steel all as shown in electrical palte No 3 connected to earthing test point incl excavation, earth work in any type of soil strata, PCC chamber, 40 mm dia GI med grade pipe as protection of strip and 15 mm dia GI Med grade watering pipe, funnel, wire mesh etcincluding testing on complete all as specified and directed.

BRR : 7710239 SPECIAL REPAIRS TO BLDG NOP-545AT CDM SECUNDERABAD UNDER GE (NORTH) SECUNDERABAD.; 1 Demolition of cement concrete in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work otherwise specifically provided for roof treatment complete all as specifiedand directed. 2 M & L for 25 mm thick PCC (1:2:4) Type B0 by using 12.50mm graded stone aggregate as in roof where require over slabs and finishing the exposed surfaces fair even without using extra cement complete all as specified and directed 3 M & L for water proof plastering 10mm thick on fair faces of brick work or concrete or roof terrace surfacesin CM 1:3 with WPC @3% by weight of cement including finishing the surfaces all as specified and directed. 4 Supply only Integral waterproofing compound for waterproof plastering complete all as specifiedand directed. 5 M & L for priming the plastered roof surfaces with bituminous primer @ 0.3 Kg/Sqm and laying the APPmodified water proofing membrane as perIS 16540-2017/ IS 16532-2017mineral finish, 3 mm thick and weighing not less than 3.8 kg/sqmreinforced with non woven polyester /HMHDPE matt black finished over compatible primer/bonding bitumen with 100 mm overlap after necessarypreparation of surface complete as per manufacturer’s instructions with bituminous aluminium paint on top @ 0.1ltr/Sqm.complete all as specified. 6 M & L for water proof plastering 15mm thick on fair faces of brick work or concrete surfaces in wall/chajja or sunken floor in CM 1:3 with WPC @3% by weight of cement including finishing the surfaces even and smooth without using extra cementall as specified and directed. 7 M & L for Rendering 5mm thick on brick work or concrete ceiling surfaces in cement mortar 1:3 including finishing the surfaces all as specified and directed. 8 M & L for Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:6 all as specified and directed. 9 Demolotion of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed 10 M & L for brick work with fly ash bricks straight or curved on plan exceeding 6 metre mean radius with old size bricks built in CM 1:6 complete all as specified and as directed. 11 Dismantling of floor, hearth or wall tilesincluding cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, all as specified and directed. 12 S & F Glazed ceramic coloured wall tiles in vertical surface 300mmx600mmx 7 to 8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 13 M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) coloured area of Each tile size 400mmx400mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 14 M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile 600mmx600mm, in floors etc. set and jointed in neat cement slurry and pointed incoloured cement to match the tiles over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 15 S & F Vitrified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) polished, area of Each tiles sizes exceeding 0.42 Sqm but not exceeding 1.00 Sqm, in skirting/daddo etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 16 S & F Vitrified Ceramic tiles Dark shade double charged 10 mm thick (square/ rectangular) matt finished, area of Each tilessize not exceeding 0.36Sqmin floors/landings/tread etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 15 mmthick screed bed in CM 1:4 all as specified and directed. 17 S & F Vitrified Ceramic tiles Dark shade 10 mm thick (square/ rectangular) matt finished, area of Each tiles size not exceeding 0.36Sqm, in skirting/daddo/riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the tiles over and including 10 mmthick rendering in CM 1:3 all as specified and directed. 18 M & L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including 15 mmthick screed bed in CM 1:4 complete all as specified and directed. 19 M & L for Kota stone slab 20-25mm thick in skirting/dadoand including 10 mmthick rendering in CM 1:3 complete all as specified and as directed 20 Demolition Stone slabs and tiles/granite tiles laid in cement mortar of any description or thickness in floors, aprons etc. 21 M & L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platfoRms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite laid over cement screed 15mm thick incm 1;4 over complete all as specified and directed. 22 Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) n exc 1.5 SqmEach etc including making good of hold fast holes with PCC Type C 1:3:6 complete all as directed. 23 Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n.exc 4Sqm Each etcmaking good of hold fast holes with PCC Type C 1:3:6 complete all as directed. 24 Taking down chowkats or frames with shutters of any description area exc1 Sqm but not exc 2 Sqm and refixing in same opening including easying adjusting and refixing builders hardware as required including renewal of unserviceable screws, welding etc., complete all as specified and directed. 25 S & F 12mm thickness toughened glass factory made frosted with CDM logo embedded as in door /wall partitionincluding providingand fixing oftop & bottom pivot & spring typefixing arrangements& necessary holes & making good & required hinges,SS 304 grade handles,door/floor spring etc and including all necesaary fittings complete all as specified. 26 S & F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed. 27 S & F 450mm long stainless steel handle as in glass doors complete all as specified and directed. 28 S & F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions.Note: Unit price quoted would be inclusive M&L for necessary scaffolding, ladders etc. inorder to work at higher heights. 29 S & F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 Sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll foRming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardwares and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 30 S & F 4 mm thick tinted sheet glass frosted, ordinary quality and glazing with oil putty in square Nexc 0.5 sq. m in Each pane complete all as specified and directed. 31 S & F 5.5 mm thick tinted sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sq. m in Each pane complete all as specified and directed. 32 S & FStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplescomplete all as specified and directed. 33 S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/Cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being teRmite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately)Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable.Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified. 34 S & FProviding and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/Cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being teRmite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately). 35 S & F of 35mm thick IInd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauze etc. divided in to square with plain chamfered or rounded mitred and rebated sash bars, any numbers, edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc, size of members of shutters as per ISI and all as specified in SSR Pt –I and as directed. 36 M & L preparation of surfaces of wood and wood based material description over 10cm in width or girth applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified. 37 S & F 125 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-22 complete all as specified and as directed 38 S & F 200 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed 39 S & F 150mm Extruded aluminium alloy handles, fabricated type, anodised all as specified. 40 M & L for 140 mm long floor doorstopper brass body and tonguewith hard drawn steel spring fixed complete all as directed 41 S & F 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed as specified and directed 42 S & F in repair Aluminium Door closerhydraulically regulated designation No.3,universal type ,suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg. complete all as specified and directed 43 S & F in repair 12 mm thick Ply wood BWR, type BB fixed with screws to walls by inserting rawl plugs in the wall/ column surfaces. 44 M & L for 0.9 mm thick colour/ white laminated sheet fixed to wooden surface with glue complete all as specified and directed. 45 S & F 100mm size hasp and staple, safety type, aluminum anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws, 46 S & F40mm dia cupboard knobs fixed with nut screw & washer or brass polished. 47 S & F ball catch spring 8mm dia steel ball and brass body and striking plate including letting in complete 48 S & F in repairs drapery curtain rod of stainless steel 25mm dia complete with stainless steel brackets and side caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screw complete all as specified and directed. 49 S & Fin repairShelves made of HDHMR (high density high moisture resistance) board manufactured with hard wood, prelaminated both sides white in colour 18 mm thick water resistant, teRmite resistant, duly edge banded with PVC taping 0.8 mm thick, cut to shape & size of shelves including dismantling board complete all as specified and directed. 50 S & F for 300 mm MS ordinary rat tail rod pattern springs and including roller and roller plate complete 51 M & L for M.S Hold fasts of FI 25 x 3 mm complete all as specified and directed. 52 S & F in repair vitreous china counter top WHB white of size 565x415x190mm or required size as approved and complete all as specified and as directed.Make:cat no: FLS-WHT-5601 of Jaquar or equivalent in ROCA/KOHLER 53 S & F in repair vitreous china wash hand basin white of bowl size 550mm x 440mm including waste coupling and PVC waste pipe 32mm dia,pillar tap cast copper alloy with capstan heads chromium plated fancy type for 15 mm bore pipe, including M S brackets complete all as specified and directed. 54 Taking out existing water closet, pedestal pattern and replacing with new EWC (Pedestal Pattern) cascade type withflush tank, seat cover etc white including fixing bolts complete including making good to floor to match with adjoining surfaces.Make:cat no: SLS-WHT-6851S220PP Jaquar or equivalent in ROCA/KOHLERas approved. 55 Taking out existing water closet, pedestal pattern and replacing with new EWC (Pedestal Pattern) cascade type withflush tank, seat cover etc white including fixing bolts complete including making good to floor to match with adjoining surfaces. 56 S & F in repair Vitreous china Urinal, Half stall type, white withwaste pipe and CP brass spreader complete including providing andfixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. Make: Cat Part No: URS-WHT-13253N of Jaquar or equivalent in ROCA/KOHLER 57 S&F Urinal partitions with touhhened frosted glass slabs terminating about 40cm above floor line, fixed in repairs complete all as specified and directed. 58 S&F in repair Vitreous china Urinal, Half stall type, white withwaste pipe and CP brass spreader complete including providing andfixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plug with and including 60mm long brass screws, pointing around urinal back in cement;flush pipe, grating and union for discharge pipe including CP Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed. 59 S & F in repair vitreous china urinal partition white of size 310x700 mm. terminating about 40cm above floor line complete all as specified and as directed 60 S & F in repairwall hung fancy type bevelledframeless looking mirror of 5mm thick size1.50mx1.20m/1.8mx1.0m or of suitablesize with quality glass with SS Studsfixed to wallwith chromium plated screws and cup washer all as specified & directed 61 M & L in repair600 X 450 mm bevelled edge mirror of selected quality glass , mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 62 S & F in repairs Stop/angle valves fancy type 15mm dia, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed. Make : Cat No: FUS-CHR-29053 of Jaquar or equivalent in ROCA/KOHLER . 63 S & F in repairs angle cock quarter turnwith flange chromium plated cast copper alloy screwed down complete all as specified and directed.Make: Johnson Eco Cat part No: T3910C or equivalent in Cera/Parryware/Hindware as approved by GE. 64 S & F in repair CP health faucet with 01 Mtr tube and hook complete all as specified .Make : Cat No: ALD-CHR-573 of Jaquar or equivalent in ROCA/KOHLER . 65 S & F in repairs 15mm size two way bib tap fancy type chromium plated, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all asspecified and directed .Make: cat no: FUS CHR 29041of Jaquar or equivalent in ROCA/KOHLERas approved. 66 S&F in repairs Two Way (2 in 1) bib taps with wall flange quarter turn suitable for 15mm bore pipe fancy type brass CP, screwed for iron pipe or brass ferrule complete all as specified and directed.Make: JohnsonVIVA series Cat part No: T4808C or equivalent in Cera/Parryware/Hindware as approved by GE 67 S & F in repairs Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed 68 S & F in repairs 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all asspecified and directed Make: Cat No. FUS-CHR-29021 of Jaquar or equivalent in ROCA/KOHLER as approved. 69 S & F in repairs Pillartap quarter turn suitable for 15mm bore pipe fancy type brass CP screwed for iron pipe or brass ferrulecomplete all as specified and directed.Make: JohnsonVIVA series Cat part No: T4801C or equivalent in Cera/Parryware/Hindware as approved by GE 70 S & F in repairs, wall mixer with provision of over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges complete all as specified and directed.Make :- Cat No FLR-CHR-5273UPR of Jaquar or equivalent in ROCA/KOHLER. 71 S & F in repairs brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges 72 S & F in repairs Soap dish, vitreous China white, approximate size 160x 160x90mm embedded in the wall 73 S & F in repairs bib tap fancy type chromium plated, crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all asspecified and directed Make : Cat No. FUS-CHR-29037 of Jaquar or equivalent in ROCA/KOHLER make as approved 74 S & F in repairs Bib cock long nose quarter turn suitable for 15mm bore pipe with flange fancy type brass CP with screwed for iron pipe or brass ferrulecomplete all as specified and directed. Make: JohnsonVIVA series Cat part No. T4806Cor equivalent in Cera/Parryware/Hindware as approved . 75 S & F sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing fixed in repairs complete all as specified and directed 76 S & F in repairs Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms)complete all asspecified and directed 77 S & F PVC (SWR) floor trap 75mm dia, plain withSS grating including jointing with solvent cement complete all as specified. 78 S & F in repairs Grating doom 100mm dia of PTMT/ SS. (Minimum weight 85gms) complete all as specified. 79 S & F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all asspecified and directed 80 S & F in repairsPVC LDPE waste pipe 32mm dia 1m lengthcomplete all asspecified and directed 81 S & F in repairs Rotational moulded polyethylenewater storage tank 3 layer white colour water tank , non- toxic effect, algae foRmation protection (made from Virgin grade of polyethylene material which is duly stabilized with anti-oxident Plastic) of capacity 500 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI/CPVC fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, 20 mm diaball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball (Minimum weight 210gms) and high pressure with crutch or butterfly handle etc complete including dismantling existing water tank complete all as specified and directed. 82 S & F in repairs Rotational moulded polyethylenewater storage tank 3 layer white colour water tank , non- toxic effect, algae foRmation protection (made from Virgin grade of polyethylene material which is duly stabilized with anti-oxident Plastic) of capacity 1000 litres, (cylindrical vertical one piece moulded with closed top), the internal and external surfaces of tanks are smooth, clean and free from any hidden internal defects, hoisted and fixed in position including S & F necessary GI/CPVC fittings, inlet/outlet washout, overflow pieces long nipples, check nuts & washer, 20 mm diaball valves high pressure of PTMT with epoxy coated Aluminum rod & high-density plastic ball (Minimum weight 210gms) and high pressure with crutch or butterfly handle etc complete including dismantling existing water tank complete all as specified and directed. 83 S & F 16 mm CPVC pipes SDR 11& Plain CPVC SDR 11fittings in trenches complete all as specified. 84 S & F 20 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 85 S & F 25 mm CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches complete all as specified. 86 Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store 87 Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store 88 Taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing or removal to store 89 S & F in repairs PVC (SWR) P trap 110mm dia complete all as specified. 90 S & F in repairs PVC (SWR) door Bend 150mm dia complete all as specified 91 S & F in repairs PVC (SWR) door Bend 110mm dia complete all as specified 92 S & F in repairs PVC (SWR) door Bend 75mm dia complete all as specified 93 S & F in repairs PVC (SWR) single T 75mm dia complete all as specified. 94 S & F in repairs PVC (SWR) single T 110 mm dia complete all as specified 95 S & F in repairs PVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 96 S & FPVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, fixedon walls complete all as specified and directed 97 S & F in repairs PVC (SWR) pipes 110mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 98 Cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, in cement mortor 1:3 cutting not exceeding 10cm girth complete all as specified and directed. 99 S & F in repairs PVC (SWR) pipes 75mm bore double socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed 100 S & FPVC (SWR) pipes 75mm bore double socketed, in any length with rubber ring joints, fixedon walls complete all as specified and directed 101 Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixingor removal to Store (measured overall as fixed along the centre line over fittings and accessories) 102 M & L for preparartion of new wall surfaces & applyingtwo coat of Plastic emulsion over a coat of a primer over 3mm thick wall care putty in two layer complete all as directed. 103 M & L for preparartion of new ceiling surfaces & applying two coats of Plastic emulsion over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed. 104 M & L for preparation of newly plastered external wall & concrete surfaces &applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ XSqm over Two coat of putty 3mm and including priming coat of exterior primer applied @ 0.90 litre/ XSqm over wall/concrete surfaces of any height complete all as directed. 105 M & L for Complete removal of existing treatment of external wall surfaces &applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ XSqm over Two coat of putty 3mm and including priming coat of exterior primer applied @ 0.90 litre/ XSqm over wall/concrete surfaces of any height complete all as directed. 106 M & L Complete removal of existing treatmentof old plastered internal surfaces of wall and applying two coats of Platic emulsion paint over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed.. 107 M & L Complete removal of existing treatmentof old plastered ceiling surfaces and applying two coats of Plastic emulsion paint over a coat of primer including 3mm thick wall care putty in two layers complete all as specified and directed.. 108 M & L for Preparing old steel surfaces of any description exc 10cm width or grith and applying one coat of synthetic enamel paintcomplete all as specified and directed. 109 M & L for Preparing old wooden surfaces of any description exc 10cm width or grith and applying one coat of synthetic enamel paintcomplete all as specified and directed. 110 M & L for 3mm thick wallcrack putty on old wall /concrete surfacesall as specified and directed. 111 M & L Precast reinforced cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings for WHB , cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces . 112 S & F for Mild steel TMT bars8mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality. 113 Dismantling of Asbestos cement (corrugated, semi-corrugated, etc. ) sheets in roof coverings . 114 S&F Pre-painted galvatume aluminium zince coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified 115 Dismantling of fillets, rails, posts, rafters, purlins, etc. under 40 sq.cm in section. 116 S & F rolled section as in main and cross beams, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connected plates confirming to Fe-410-W.Gde E-250 ,Quality A 117 M & L preparation ofnew steel surfaces of any description, over 10 cm in width or girth, not otherwise described, applying two cots of eynthetic enamel paint over red oxide, zinc chrome primer complete all as specified and as directed. 118 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets all as completed. 119 S & F GI frame work Size of gnd 605 x 605mm for seamless celling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centrelintermediate channel 0 9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including coiling section (not exc 12 m length) of 0.55 mm thickness having kurfed web of 50 mm and fiange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and Hangers 6 mm dia G. (upto 1200mm length) adjusting level fixed to root stabs by means of ceiling cleats made out of G1 flat 40 x 3 mm size 60mm long and expansion hold fasteners 12 5mm dia, 40mm long complete all as specified.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 120 M & L for Providing and fixing 12mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with G1 wire mesh (Fillets, metal frame work and GI wire mesh paid separately) with specified shape and architectural elevation complete all as specified an directed by Engineer in Charge.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 121 M & L for preparation of new gypsum board ceiling surfaces & applying two coat of Plastic emulsion paint over a coat of alkali resistant primer over plaster of pans putty of 2 mm thickness on ceiling surface complete all as specified.Note: Unit rate quoted shall include for necessary scaffolding, trestlers, ladders & cradlers required for execution of work 122 M & L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed 123 S & F in repairs standard wall mount stainless steel hand sink features a countertop edge with an offset to guard against drips and overflow, 1.00mm thick for kitchen or laboratory, with plug, wastepipe, washers, including cantilever castiron brackets, connecting union etc., overall size 2.3m X 0.45m with bowl size 2.0m X 0.35m X 0.4m complete all as specified and as directed.Note: Effective/clear dimensions of sink can be varried by ±5% with prior approval. 124 Taking down existing unserviceable point wiring of any description/type/ size of light/ fan/tube/power/two way/bell point etc on TW batten/conduit includingremovalof batten / conduit / gutties / wooden boards / switches / sockets / regulators/ light fittings etc and removal of unserviceable material out of site and making good the disturbed surfaces of wall/ceiling so as to match with the existing finishes all as specified. 125 Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as per existing at site including making good the disturbed surfaces to match with the existing finishes all as specified. 126 Taking down carefully by unscrewing from boards/ outlet boxes, fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, brackets, ceiling fittings, bulk head fittings, tube light fittings and regulators, etc. for reuse at site complete all as specified and directed. 127 M & L for Point wiring on concealed conduit with 1.5 Sq mm FRLS copper conductor single core PVC insulated sheathed 1100 V multistranded drawn through including rigid PVC conduit and conduit of dia medium grade and modular accessories including fixing/grouting sunken/ surface along with modular flush box of sutiable thickness covered with suitable modular cover plate including running up of 1.5 Sq mm FRLS copper conductor PVC insulated cable as earth continuity conductor along with wiring and connecting to the common earth dolly for fixing the switches/ sockets/ regulators etc all as specified for : NOTE: Rate of Modular Flush box and Cover plate are inclusive of rate quoted by the contractor 128 (a) One light/fan/Bell point controlled by one, one way switch 10 A, SP 129 All as per SL No 127 above but One 2/3 pin 5 Amps switch socket outlet point controlled by one switch on the same board. 130 All as per SL No 127 above but One 3 Pin 5 Amps switch socket Independt board. 131 Description all as per item No 127 here-in-before but using 2.5 Sq mm FRLS single core copper conductor cable of multistranded PVC insulated unsheathed 1100 Volts grade for 5/15 Amps switch socket combination point including running of 2.5 Sq mm FRLS copper conductor PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly. 132 S & F Modular switch 1 way 10 A, 1 Module capacity 230 volts. 133 S & F Modular switch 1 way 16 A, 1 Module capacity 230 volts. 134 S&F Modular Bell Push 6A, 1 Module. 135 Supply and fix socket outlet modular type multipurpose 2/3 Pin, 10 amps, 230 volts combined 2 Module complete all as specified & directed. 136 Supply and fix socket outlet modular type multipurpose 2/3 Pin, 6/16 amps, 230 volts combined 2 Module complete all as specified & directed. 137 S & F Modular ceiling fan regulator stepped type heavy duty suitable to work on 230 volts, 2 Module complete all as specified & directed. 138 S & F calling Bell, AC, 230 volts, single polecomplete all as specified & directed 139 S & F ceiling rose three terminal surface bakelite type AC 50 Hz 230 Volts of size 65 x 50 mm complete all as specified. 140 S & F in replacement of Single pole and Neutral enclosure with a three pin and earth plug and socket metal clad complete with one singlepole MCB 20 Amps (AC Box) all as specified and directed. 141 S & F in replacement of Triple pole and Neutral enclosure with a two pin and earth plug and socket metal clad complete with one singlepole MCB 32 Amps (AC Box) all as specified and directed. 142 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 volts with ncluding 200 Amps MCCB 25 KA as incomer and 01 Nos outgoing TP MCBs of 63 Amps and 15 Nos outgoing SP MCBs withincluding provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified.Note : MCB SP/TPs shall be measured and paid seperately. 143 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 voltsincluding 200 Amps MCCB 25 KA as incomer and 06 Nos outgoing TP MCBs of 63 Amps with suitable rated copper bus bar with neutral link including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. Note : MCB SP/TPs shall be measured and paid seperately. 144 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 4 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link with suitable rated bus bar 415 voltsincluding including 100 Amps MCCB 25 KA as incomer and 02 Nos outgoing TP MCBs of 63 Amps and 06 Nos outgoing SP MCBs including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. Note : MCB SP/TPs shall be measured and paid seperately. 145 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 4 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link with suitable rated bus bar 415 voltsincluding including 100 Amps MCCB 25 KA as incomer and 01 Nos outgoing TP MCBs of 63 Amps and 09 Nos outgoing SP MCBs including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified.Note : MCB SP/TPs shall be measured and paid seperately. 146 Supply, fix, connecting in replacement and testing factory made, distribution board, (MCB DB) TPN, 4 Way, having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral link including provision for MCB TPN as incomer and SP MCBs as outgoing and total number of modules equal to MCB TPN + 12 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, complete all ass specified and as directed. Note: MCB TPN and MCB SP will be measured and paid seperately. 147 S&F in replacement sheet metal enclosure vertical type MCCB DB TPN 6 way double door having degree of protection IP 43-IK 09 with metal double door, 415 Volts, flush type made out of 1.2 mm thick thick CRCA sheet, metal duly powder coated and confirming to IS 8623 with suitable rated copper bus bar with neutral linkwith suitable rated bus bar 415 voltsincluding 250 Amps MCCB 25 KA as incomer and 03 Nos outgoing TP MCBs of 63 Amps and 09 Nos outgoing SP MCBs with suitable rated copper bus bar with neutral link including provision for MCCB TPN as incomer and SP/TP MCBs as outgoing and total number of modules equal to MCCB TPN + 18 with blanking plates and fixed flush to wall and making good the disturbed surfaces etc, with magnetic locking system complete all as specified. 148 Supply, fix, connecting in replacementand testing MCB, Triple Pole Neutral (TPN) 40 to 100 Amps, 415 Volts of rupturing capactiy 10 KA, C Seriescomplete all as specified and as directed. 149 Supply, fix, connecting in replacementand testing MCB, Triple Pole TP 25 to 63 Amps, 415 Volts of rupturing capactiy 10 KA, C Seriescomplete all as specified and as directed. 150 S and F in replacment of sheet metal enclosure MCBDB SPN 12 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 151 S and F in replacment of sheet metal enclosure MCBDB SPN 8 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 152 S and F in replacement of sheet metal enclosure MCBDB SPN 6 way with suitable rated bus bar 240 Volts double door with magnetic locking system complete all as specified. 153 Supply, fix, connecting in replacement and testing MCB, Single Pole Neutral (SPN) 40/63 Amps, 415 Volts of rupturing capactiy 10 KA, C Series complete all as specified and as directed. 154 Supply, fix, connecting in replacement and testing MCB, Single Pole (SP), 6-32 Amps, 240 volts of rupturing capacity 10 KA, C series complete all as specified and as directed. 155 S & F in replacement Surface Modular Box of 6 way along with 6 way Modular plate and2 Nos of 16 Amps Switches and 6/16Amps multipurpose Sockets with connected internal wiring complete all as specified and directed by Engg in Charge. Note: Modular Plate, Switches & Sockets are inclusive of the rate quoted. Make: Indo Asian cat No. 800186,800166, 800103,800122 or equivalent make in Anchor Roma 156 M & L for Submain wiring with two single core 2.5 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of2.5 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length.NOTE: SUBMAIN WIRING SHALL BE REPLACED IN MAIN LOBBY OF OFFICER MESS WHICH IS AT HEIGHT IN THE RANGE UPTO 15 MTRS, COST OF SCAFFOLDING FOR RE-WIRING IF REQUIRED SHALL BE BORNE BY THE CONTRACTOR. 157 M & L for Submain wiring with two single core 4 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of4 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 158 M & L for Submain wiring with two single core 6 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of6 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 159 M & L for Submain wiring with four single core 6 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of6 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-four runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 160 M & L for Submain wiring with four single core 10 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of10 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-four runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 161 M & L for Submain wiring with two single core 10 Sq mm FRLS PVC insulated copper conductor multistranded 1100 Volts grade drawn through andincluding rigidPVC conduit and concealed conduit accessories of suitable dia medium grade including running up of one runs of10 Sq mm FRLS copper conductor multistranded PVC insulated cable as earth continuity conductor along the wiring and connected to the common earth dolly completeincludingremovingtheexistingunserviceablesubmain wiringandmakinggood thedisturbed surfaceto match with the existing all as specified.Note:-two runs of cable, one run of earth contuinity conductor and one run of conduit shall bemeasured and paid as one unit length. 162 Taking down ceiling fan/ exhaust fan, sealing cable end,dismantling blades, removing fan and shifting the all unserviceable ceiling fans/exhaust fans to MES store complete all as specified and directed. 163 Supply, fix, test and commissioning of Energy efficient ceiling fan with three blades, down rods andaccessories, 230V,1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE , Five star rated with brushless direct current motor (BLDC) fixed to roof/ceiling with suitable clamp including provisioning of flexbile copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan etc., complete all as specified and as directed. 164 Supply, fix, test and commissioning of Exhaust fan, metal body, AC single phase, 230 V of size 450 mm sweep heavy duty, 4 blades, copper winding with louvers shutters connecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. 165 Supply, fix, test and commissioning of Exhaust fan, metal body, AC single phase, 230 V of size 300mm sweep heavy duty, 4 blades, copper winding with louvers shutters connecting up onnecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. complete all as specified and as directed. 166 Supply and Fixing Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, Voltage 230 V, 50 HZ, RPM 1200, Copper winding of 250mm sweepconnecting up with and including provision of PVC insulated copper flexible cord from ceiling rose to connection of exhaust fan complete all as specified. 167 Taking down the geysers of capacity 25/35 from its mounting position by removing all water and electric connections and de-assembling the geyser after carrying out the following works, (a)Descaling, cleaning the inner tank thoroughly and there should not be any bad taste of water.(b)Examining the water tightness of storage tank after cleaning.(c)Examining the physical condition of thermostat, base assembly fusible plug and outer tank for its serviceability.(d)Inspection of pilot lamps.(e)Reassembling the geyser parts and testing including checking all electrical system (ensuring there is no current leakage) and also conducting hydraulic testing.(f)Re-fixing the Geyser and making electric connections,inlet and outlet water connections and testing and checking of all water inlet, outlet valves connected with geysers.Note : Defective /worn outpartsif required shall be measured and paid separetely under relevant items in this schedule. 168 Supply and fix rubber PVC connection of 2/3 feet complete, all as specified and as directed. 169 Supply & fix MS base plate cup any type with screws of suitable size as per requirement complete, all as specified and as directed. 170 Supply & fix heating element of the 1/1.5 KW rating as required at site including rubber washers of any make and type complete as per sample, all as specified and as directed. 171 Supply & fix Steel inner tank of 25 litre capacity geyser tank by made out of steel sheets appropriate thickness complete, all as specified and as directed . 172 Supply & fix thermostat suitable for the geysers of 25 Liters capacities complete, all as specified and as directed. 173 Supply & fix auto cut suitable for the geysers of 25 Liters capacities complete, all as specified and as directed. 174 Supply & Replace Air Release Valve suitable for geyser 25/50 ltrs all as specified and directed. 175 Supply and Fix Rigid non-metallic PVC conduit 25mm inclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and directed. 176 Supply and Fix Rigid non-metallic PVC conduit 20 mm inclusive of boxes (junction/terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc.complete all as specified and directed 177 Supply and Fix Rigid PVC Casing & Capping of 25 mm wide including all accessories required for drawing of 1.5/2.5 sqmm wire complete all as specified and directed 178 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed. 179 S & F in replacement of wall mounted batten type LED light of 12 watts with aluminium extruded batten and system lumens of 1200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver completeand connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling roseall as directed.Make: Philips Model BN021 LED12S PSU GR or equivalent make in Havells/Wipro/GE. 180 S & F in replacement of wall mounted batten type LED light of 20/22 watts with aluminium extruded batten and system lumens of 2200 lm minimum with IP & surge protection alongwith driver efficiency >85% and power factor >0.95 , colour rendering index CRI>80 along with integrated driver completeand connecting to the point wiring with necessary flexible copper conductor of multistrand three core of suitable length from fitting to the ceiling roseall as directed.Make: Philips Model BN021C LED22Sor equivalent make in Havells/Wipro/GE. 181 S & F in replacement of Security Lights of 25 watt LED light with high power LED and unique peanut lens to ensure uniform distribution with suitable pipe bracket 32 mm dia 0.60 Mtr length fixed on wall with suitable flat iron clamps and nut bolts including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed.Make: Havells Model ENDURASUNDOWNSL25WLED765PASYBOPCIHDor equivalent make in Wipro 182 Supply and fixing LED flood light 100 watt 230 V AC outdoor type with thermal management inmultiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp fixed on wall with suitable flat iron clamps and nut bolts including connecting to multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 183 S & F of LED Luminarie 600mmx600mm 35/36 watts, 220 volts AC recessed mounting light fixture type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof ceiling including connecting up with driver 3 core flexible copper conductor cases of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed by Engg-in-Charge . Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. 184 S & F in replacement of round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamps suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed by Engg-in-Charge . Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. . 185 S & F in replacement of round shape spot light of 06 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders LED lamps suitable for roof ceiling including connecting up with 3 core flexible copper conductor cable of suitable size complete with lumianrie system efficacy >100 lm/wwith IP & surge protection of 10 kV, power factor >0.95 complete with all accessories all as specified and directed. Note: Cutting of False ceiling and re-arranging the False ceiling with existing size, Gypsum board/POP false ceiling is to be done if required. Cost of False ceiling work is inclusive of rate quoted. 186 Supply, fix, test and commissioning of Decorative wall mounting fixture of 09 Watts in durable plastic body and designer mesh in gold finish suitable for 9 W LED lamp complete with all accessories all as per Cat No LHFOECE1TZ1B014 of Havells or techno- commercially equivalent of other specified makes connecting up with and including twin/ three core twisted flexible copper conductor cable of suitable size etc. complete all as specified and as directed. 187 Supply and Fix in replacement of 2 module Modular white cover plate with frame complete all as specified and directed 188 All as per Ser item No 184 but 3 module Modular white cover plate with frame. 189 All as per Ser item No 184 but 4 module Modular white cover plate with frame. 190 Supply and fix in replacement ofPVC Round blocks ofsize 4for proper mouting LED tube lights alongwith connected items for fixing complete all as specified and directed. 191 Refixing of Serviceable items obtained from ser item No 3 such as LED security light/ flood light fittiingswith suitable pipe bracket 32 mm dia 0.60 Mtr length fixed on wall with suitable flat iron clamps and nut bolts including provision of 1.5/2.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 192 All as per ser item No 188 but items such LED tube light/Ceiling light fittings alongwith connected switch & sockets including provision of 1.5 sqmm 3 core multistranded copper conductor cable from light fitting to junction box complete all as specified and directed. 193 Earthing complete with galvanised steel earth plate electrode 60cm x60cm x6mm thick buried directly in ground earth pit not less than 2.25 mtr deep below normal ground level ) with top edge of plate not less than 1.5m below ground level, connecting to the Galvanised iron earth earth lead 4 mm dia, by means of nuts, bolts,check nuts and washer etc of galvanised iron and earth lead protected by provision of GI pipe light grade 15mm bore from earth elelctrode to test pointincl provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded stone agagregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 25 x 25x6mm with lugs 2 Nos and with 6mm dia MS bar handle made to shape, GI pipelight grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling test point made out of Bronze/Gun metalwith fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning in and removal of surplus soil to a distance not exceeding 50mtr, all as per electrical plate No 5 of SSR Part-I and connection to earth test point all as specified incl testing on completion. Note :- Item of Earthing includes cost of 7.5m long galvanised iron earth lead 4 mm size and protection pipe of 15 mm bore GI light grade.

BRR : 8132810 Tender For Special Repair To Building No Np-03 (Unit Mandir) At 189 Fd Wksp Coy And Bldg No T-21/23 (Ch And Dh) Ors Mess At 68 Engr Regt At Naa Under Ge (N) Tezpur.; 1 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 sqm each complete all as specified and as directed 2 Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 sqm but not exceeding 4.00 sqm each complete all as specified and as directed 3 Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water etc, complete all as specified and as directed. 4 Material and labour for brick work with sub-class B old size bricks of class designation 75, straight or curved on plan exceeding 6m mean radiusbuilt in cement mortar (1:6) including dismantling of existing brick work built in cement mortar complete in all respect as specified and directed. 5 M&L for half brick work with subclass ‘B’ old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantalling of brick work built in cement mortar in any position, complete in all respect as specified and directed. 6 M&L for cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks, filling of pressed steel door frame, fixing of hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks including dismantling of existing surface complete all as specified and directed. 7 S&F in repairs framed work such as grills, gratings,etc with ends of bars shouldered and /or riveted, or forged into spikes framed guard bars barred iron doors , laddersand similar work conforming to Fe 410-0 or FE310-0 complete all as specified and directed. 8 S&F in repairs Rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality A) including necessary welding complete complete allas specified and directed. 9 M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor including taking down existing sheet complete all as specified and directed. (Crimp curve profile sheet shall be provided at end of Roof Sheet (Galvalume). 10 S&F coloured 0.50 mm thick pre-painted galvalume aluminium zinc coating GI based trapezoid profile steel sheet having tensile strenght of 550 Mpa as in ridge, valley gutter or of similar type, fixed with self tapping screws with bitumen washer to truss members of any material, including taking down existing sheet complete all as specified and directed. (The measurement shall be carried out as in a plain sheet). (Crimp curve profile sheet shall be provided at end of Roof Sheet (Galvalume).Note : The work shall be done at the height upto 15 meters from ground. 11 M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor including taking down existing sheet complete all as specified and directed. (Crimp curve profile sheet shall be provided at end of Roof Sheet (Galvalume). 12 S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping, of grid size 600 x 600 mm comprising of wall/ cleat angle of size 25x25x0.35 mm and corss tee of size 24x38x0.70 mm with 4 mm dia GI wire as suspender and including 4 mm thick decorative pre-painted non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/ wooden truss of any type including dismantling of existing false ceiling boards, complete in all respect as specified and directed. (Make:- Eternit, Everest or equivalent) 13 M&L for skid/non skid ceramic (coloured) tiles of 7-8 mm (square or rectangular) area of each tile exceeding 0.18 sqm but n.exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 15mm thick screedbed in CM 1:6including dismantling of existing surface complete all as specified and directed. 14 Providing and laying coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.08 sqm but not exceeding 0.15 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, including dismantling of existing surface complete all as specified and directed. 15 Material and labour for any colour of granite stone without white spots Granitestone slab 17-19mm thick, as in floor, dado, steps, laid over and including screed bed 15mm thick in cement mortar (1:6), jointed and pointed with white cement mixed with pigment to match the shade of stone including cutting, rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe holeetc., to the entire satisfaction of the Engineer-in-Charge complete in all respect as specified and directed. 16 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of wall in cement mortar (1:4), finished even & smooth without using extra cement, including taking down existing surface complete all as specified and directed. 17 M&L 15 mm thick plastering on brick/ stone/ concrete surfaces of of wall in cement mortar (1:6), finished even and smooth without using extra cement, including taking down existing surface complete all as specified and directed. 18 Supply only integral water proofing compound complete all as specified and as directed. 19 S&F in repair 15 mm bore GI tubesmedium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed. 20 S&Fin repair 20 mm bore GI tubesmedium grade, galvanished with all fittings fixed complete to walls and ceiling or laid in floors complete in all respect as specified and directed. 21 S&F in repairs 20 mm gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed to pipe complete all as specified and directed. 22 S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of size and shape including fixing with aluminium U shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) 23 M&L for anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and as directed. 24 S&F mortice lock, vertical type, mild steel, 2 levers, vertical type, 100 mm size including protective coating of painting fixed in position complete all as specified and directed. 25 S&F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mmincluding necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) complete in all respect as specified and directed. 26 S&F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of appd make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) 27 S&F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note:all external members to be joined at 45 degree angle at corner) 28 S&F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed. 29 S&F 4 mm thick figured glass, pin head type and glazing with oil putty or fixed with beads in square not exceeding 0.5 sqm in each pane complete all as specified and as directed. 30 Supply & fix sheet glass, ordinary quality, 4 mm thick and glazed with oil putty or fixed with beads in square not exceeding 0.5 Sqm in each pane complete all as specified and directed. 31 S&F in repairs stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed. 32 S&F in repairs PVC coloured insulated over MS pipe 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed. 33 S&F 1800 mm X 600 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and as directed. 34 Supply and fixed in position two layered ISI marked rotational moulded polyethylene water storage tanks of 1000 litres capacity (cylindrical vertical with closed top) including cover, using new GI tank/PPR or other type of material tank nipples and unions for inlet and outlet pipe connection of same internal bore dia. and one for cleaning with dead plug , including dismantling and taking down of old unserviceable water storage tank complete in all respect as specified and directed. 35 S&F in repairs PTMT ball valve high pressure 20mm bore with epoxy coated aluminium rod & high density plastic ball screwedfor iron/CPVC pipe/fittings complete all as specified and directed. 36 M&L for PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed. 37 S&F in repairs 15 mm nominal size, nonrising spindle type fancy angle stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed. 38 S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed. 39 S&F brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed. 40 S&F in repair Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with brass chromium plated bracket guard and railing 60 cm long complete in all respect as specified and directed. 41 S&F in repair counter top wash hand basins, vitreous china of size 500mmx400mmx800mm (flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, including bottle trap and 15mm bore dia fancy type CP finish long neck pillar tap, cast copper alloy with capstan heads, screwed down high presure, with or without letterd hot or cold with long screwed shanks and fly nuts, screwed for iron pipes including dismantling of existing surface complete all as specified and directed. 42 M&L for hardcore (broken stone or boulders) of gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed. 43 S&F 75 mm dia of outlet, PVC (SWR) nahani trap, plain with SS grating of size 150mmX150mm, 0.75mm thick openable at center including jointing with solvent cement, complete in all respect as specified and directed. 44 S&F PVC (SWR), type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 75 mm dia, laid in trenches complete all as specified and directed. 45 S&FPVC (SWR) Tee(87.5⁰) single, 75 mm dia with inspection door conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge. 46 S&FPVC (SWR) bends without inspection door (any angle), 75 mm dia conforming to IS 14735: 1999 complete all as specified and directed. 47 Supply and fixed unplasticised PVC (SWR) Gully trap125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed. 48 M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete complete all as specified and as directed. 49 M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed. 50 M&L 75 mm thick PCC (1:3:6) type C-2 using 40 mm nominal size crushed and graded stone aggregate laid in floor, path etc. or of similar type finished the surface even and fair without using extra cement complete in all respect as specified and directed. 51 Providing & laying heavy duty non skid coloured digital printed floor tiles of size 300mmX300mm ,8 to 10mm thick set and jointed in neat cement slurry and pointed with white cement with pigment to match the tiles colour over and including 15mm thick screed bedding in cm 1:6 and dismentling of existing tiles/blocks of any discription complete in all respect as specified and directed. 52 M&L for cement concrete in foundation, filling and mass concrete in M7.5(Nominal Mix) using 40 mm nominal size graded crushed stone aggregate complete all as specified and as directed. 53 M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed. 54 Material and labour for complete removal of existing treatment on wall and applying two coats of oil bound distemper and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2mm thick (in two layers), wall care putty complete in all respect as specified and directed. 55 M&L for preparation of old decorated plastered surface of ceiling and applying two coats of oil bound distemper including filling of voids with wall care putty on plastered surface including complete removal of existig treatment, complete in all respect as specified and directed. 56 M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed.L̥ 57 M&L for preparation of newly undecorated plastered surface of wall and applying two coats of oil bound distemper (OBD) and finished another one coat with spunge roller over one coat of alkali resistant priming paint over 2 mm thick (in two layers), wall care putty, complete in all respect as specified and directed. 58 M&L for preparation of new or previously untreated wood or wooden surfaces, of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. 59 Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge 60 M&L for preparing of old decorated wooden surface, of any description, not otherwise described, over 10 cm width or girth, and applying two coats of synthetic enamel paint, complete in all respect as specified and directed. 61 M&L for preparation of old decorated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint, complete in all respect as specified and directed. 62 S&F in repairs second class hardwood plain,solid ,straight,chowkats and frames,wrought, framed rebated on the solid ,rounded or chamfered,put together with glue pinned at joints, complete in all respect as specified and directed. 63 M&L for 18-20 mm thick machine cut kota stone slab flooring of size not less than 500 x 500 mm over 15 mm thick cement mortar (CM) 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed. 64 M&L for 20-25 mm thick machine cut kota stone slab of size not less than 500 x 500 mm in riser of steps, skirting, dado and pillar over 15 mm thick rendering in cement mortar (CM) 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed. 65 M&L for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate, 25 mm thick in sub base for laying tiles, pavings, floorings etc. including dismantling of existing surface complete all as specified and directed. 66 S&F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 250 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed. 67 S&F cast aluminium alloy handle, cast type, 125 mm size, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. 68 S&F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed. 69 S&F flush door shutters, 30 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed. 70 S&F 100mm size mild steel butt hinges complete allas specified and directed. 71 S&F in repairs GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete in all respect as specifified and directed. 72 M&L second class hardwood 35 mm thick, timber species of super group and durability class II as per IS 12896: 1990 and first grade as per IS 1003 (Part-1): 2003, factory made, glazed and skeleton shutters, open rebated and prepared to receive glass, wire gauze, etc. (without sash bar), edges of framing plain, cham104fered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part-I section 8 Clause 8.24 (a) complete all as specified and as directed by the Engineer-in-Charge. 73 S&F for coloured rubber moulded, glazed pre coated chequered cement concrete tiles of any shape and size 20-25mm thick with grey cement with pigment,; set jointed and pointed in neat cement slurry with pigment in floors including over 15mm thick screed bed in CM 1:4 including dismantling of existing surface complete all as specified and directed. 74 M&L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed 75 S&F in replacement of point wiring with 1.5 sqmmFRLSH, PVC insulated stranded copper conductor single core including non metalic PVC conduit(MMS ISI) of size not less than 20 mm on wall/over ceiling,modular metal boxes of required size and with modular plates incl of all accessories and all as specified including 1.5 sqmm FRLSH PVC insulated sheathed multistranded copper earth conductor to common earth and connected to earth dollyfor light / fan/ bell point controlled by one switch.Note:- (i) Cost of PVC conduit, modular plates,frames, cover plates etc and cement mortar after wall chasis to make good disturbed surfaces; are deemed to be included in the quoted rate. 76 All as per item 75 here-in-before for 3 pin 5 amps switch socket combination on indpendent board with 1.5 sqmm capper cable complete all as specified and as directed. 77 All as per item No. 75here-in- before but for 3 pin 16 Amps switch socket combination on independent board with 2.50 sq mm copper cable complete in all respect as specified and directed. 78 All as per item 75 above but for One 3 pin socket outlet 5 Amps on same board complete all as specified and as directed. 79 S&F in replacement of modular switch10A,1 module single pole, one waycomplete all as specified and directed. 80 S&F in replacement of modular socket outlet 5 pin ,6 Amps,2 module, 240 Volts complete all as specified and directed. 81 S&F in replacement of modular socket outlet 5 pin ,16 Amps,2 module, 240 Volts complete all as specified and directed. 82 S&F in replacement of modular switch16A, 1 module single pole, one waycomplete all as specified and directed. 83 S&F in replacement ofceiling rose polycarbonate typethree terminals complete all as specified and directed. 84 S&F in replacement of modular step type electronic fan regulator ,two module 120 watt single pole 240 Volts complete all as specified 85 S&F in replacementLED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 86 S&F in replacement new generation energy saving and environmental friendly long life 35/40W LED wall street light made up of pressure die cast aluminium housing with high efficient LED as lighting source and PC cover having top Opening seperate driver compartment with IP66 protection and impact resistance of IK07including necessary brackets (made out of suitable bore GI pipe light grade appx 0.6 meter long bend to shape) nuts, bolts, etc fixed on walls with MS clamp complete all as specified and directed. 87 S&F in replacement of LED luminaire 600 mm x 600 mm, 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and directed. 88 S&F in replacement of submain wiring with two single core 6 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduitincluding 6 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete.Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted. 89 Taking down ceiling fan any type/ size from hook and dismantling cable and blades and bring in to contractor store for repair and hanging ceiling fan in position after repair, greasing etc. with existing flexible copper cable complete all as directed. (rewinding of fan, painting and spare parts required shall be deemed to be included in the quoted rate) 90 Supply, Laying, testing & commissioning replacement of UG LT cable XLPE insulated screened PVC bedded, galvanized steel strip armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 25 Sqmm x 4 core including connecting the cables at both ends by providing suitable size aluminium lugs at the termination ends and necessary saddle clamp all as specified and directed by Engg-In-charge. 91 Excavating in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. or for cable laying or water supply pipes lines etc or not exceeding 10 sqm on plan and getting out in soft/ loose soil complete all as specified and as directed. 92 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in soft/ loose/ hard/ dense soil complete all as specified and as directed. 93 Removing excavated material (soils) not exceeding 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed. 94 Supply & spreading in trenches sand cushioning to underground cable in trenches including spreading, levelling hand punning down complete all as specified and directed Note:- Depth of sand cushioning will be measured after punning down and levelling the sand properly. 95 M&L laying well burnt old size bricks, sub calss B bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all complete all as specified and directed. 96 Supply and fixing in replacement single pole and neutral enclouser with two pin and earth plug and socket complete with one single pole MCB 20 Amps ,240 volts complete all as specified and directed. 97 S&F in replacement of sheet metal enclosure MCB DBs SPN , 12 way 240 V, with 100 A rated bus bar , double door, IP 43 as per IEC 61439-3 , suitable for flush mounting and surface mounting complete all as specified and as directed. 98 S&F in replacement ofMCB single pole (SP) 6 to 32 Amps,240 volts , C curve , AC complete all as specified and directed. 99 S&F in replacement of MCB Single pole & neutral (SPN)63 Amps, 240 volts , C Curve, AC , 10 kA complete all as specified and directed. 100 M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Metre below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 15 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as shown on electrical plate No. 3 of SSR part - I , including taking out old U/s complete alll as specified and directed . 101 M&L fortaking down and rewinding of Exhaustfan upto 380/480/450 mm sweep after dismantling and taking out the burnt winding coils and rewinding with super enamelled copper winding wire of suitable size and gauge including insulation, Varnishing, drying etc complete and refixing the same after rewinding and testing complete all as specified and directed. 102 S&F in replacement of submain wiring with two single core 4 sq mm FRLSH PVC insulated copper cable 1100 volts grade multi stranded, sheathed conductor in concealed PVC conduitincluding 4 sq mm multi-strand FRLSHPVC insulated copper wire for earth continuity conductor connected to common earth dolly complete and making good disturbed surface complete.Note:- Cost of PVC conduit, cutting chases on walls and making good disturbed wall surfaces including finishing with cement mortar (1:4) matching with the existing shade / tint are deemed to be included in the rates quoted.

BRR : 6883826 SPECIAL REPAIR TO BLDG NO. P-47 (IIT BRANCH) HQ 2C UNDER GE (NORTH) AMBALA CANTT-- 1 SCHEDULE A PART I (B/R WORKS)M & L for taking down cement of cement lime plaster of any description on brick or stone walls etc including ranking out joints hacking for key scrubbing down with water etc including removal of debries to distance n exc 250 mtr complete all as specified and directed. 2 M&L15 mm thick cement plaster on fair faces of bricks or concrete wallsin CM 1:4 finished even and smooth with out using extra cement on brick work or concrete surfaces complete all as specified and directed. 3 M&L15 mm thick cement plaster on other then fair faces of brick works in CM 1:6 finished even and smooth with out using extra cement on brick work or concrete surfaces complete all as specified and directed. 4 Supply and fixing in replacement of GI OREO Metal Suspended ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using Gi slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of Gl sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece complete all as specified and directed. 5 S&F in replacement 5-8mm thick solid/ hollow profile designer PVC panelling with panel of width 250mm to 300mm fixed to wall/ceiling with screw and rawl plug including PVC fillets& beading (U.L section) wherever required as per manufacturer instruction complete all as specified and directed. 6 Demolition of cement concrete (Unreinforced) of any description in any position not otherwise specifically provided forincluding removal of debries to distance n exc 250 mtr complete all as specified and directed. 7 Material and labour for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry over and including 15 mm thick screed bed in CM 1:4, jointed and pointed in white or coloured cement to match the tiles complete all as specified and directed. 8 M&L for providing 75 mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub floor, sub bases complete all as specified and directed. 9 Material and labour for preparation of newly plastered or unplastered of wall surfaces, cornices etc. and applyingtwo coats of distemper oil emulsion over a coat of chalk whiting complete all as specified and directed. 10 Complete removing of existing of old decorated brick/concrete, plastered / un- plastered surfaces of walls by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of oil bound distemper over 1 mm thick putty prepared surfaces of the walls pillars, cornices etc. complete all as specified and directed. 11 Complete removing of existing old decorated brick/concrete, plastered / un plastered surfaces of walls, pillars cornices etc by brooming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying two coat of cement base paint on the walls pillars, cornices etc. complete all as specified and directed. 12 Material and labour for preparation of newly plastered of wall surfaces and applyingtwo coats of cement base paintover a coat of alkali resistant primer complete all as specified and directed. 13 Demolition of mud in roof any thickness whether full thickness removed or part thereof including plaster & leaping including removal of debries to distance n exc 250 mtr complete all as specified and directed. 14 M&L for brushing neat cement slurry with 3 kg of cement per sq. metre complete, all as specified and directed. 15 M & L for providing cement concrete 1:2:4 type B-0, using 12.5 mm graded crushed stone aggregate as in roof kerbs, mud stops, padding or filling roof depressions etc. complete all as specified and directed. 16 M&L for roof treatment on roof for providing and laying 3mm thick APP (atactic polypropylene polymer) modified prefabricated five layer weight not less than 3.60 kg/Sqm water proofing membrane black finish reinforced with non woven polyster matt and consisting of a coat bitumious primer @ 0.40 ltr /Sqm by the same membrane manufactures of density 0.87 to 0.89 kg/ltr at 25°C temprature and viscosity 70-160 cps over the primer coat with overlap of 75mm at the at the side and 100mm at the end, the layer membrane shall be laid using butane gas torch and sealing all joints etc after preparing the surface complete as per standred practice as per manufactures instructions. The vital physical and chemical parameters of the membrane shell be under :-(i) Joint strength in longitudinal and transverse direction at 23°C at 650/450 N/5 cms.(ii) Tear strength in longitudinal and transverse direction at 300/250N/5 cms. Softing point of membrane not less then 150°C when tested in accordance with ASTM (d- 5147). (iii) The laying of membrane shell be got down through the authorised applicator of manufactures of membrane only.Note: The contractor will carry out ponding test after application of APP treatment before claiming payment. 17 Material and labour for cement concrete tiles 20cm x 20cm x 20mm thick, machine pressed, set jointed and pointed in neat cement slurry in roofs, and cut and polished with grey cement no pigment over and including 15mm thick screed bed CM 1:4, complete all as specified and directed. 18 Taking down shutters of any description exc 1 sq. m and not exc 2 sq. m each and making good the disturbed surfaces as per existing complete all as specified and as directed. 19 Supply and fixing for aluminium alloy anodized (powder-coated) door frame and shutters with hollow aluminium anodized sections as specified including aluminium alloy anodized snap type beads, dish type door handles, glazed clip joint cleats, rubber gasket, dead lock 4 levers, two numbers of aluminium alloy anodized tower bolts to each leaf etc. including fixing frame to wall/RCC members with rawl plugs complete. Sections of doors shall be aluminium hollow sections as follows - (a) Door Frame single groove 101.6mmx44.45mmx2 15mm thick(b) Shutter top 47.62mmx44 45mmx1.95mm thick(c) Shutter bottom 114.30mmx44 45mmx2 15mm thick(d) Shutter vertical 85mmx44 45mmx1.80mm thick(e) Shutter middle 83.5mmx44.45mmx2.40mm thick (f) Gauging clip weighing not less than 0.097kg/metreNote:Glass pane shall be measured and paid separately. 20 Supply and fixing 12mm thick prelaminated particle board , interior grade prelaminated both side with decorative choice laminations &fixed with aluminium frame work or screws to timber frame work complete all as specified and directed. 21 S&Fof 4mm thick sheet glass ordinary quality, frosted on one side, in square n.exc 0.5 Sqm in each pane, fixed with aluminium beading complete all as specified and directed. 22 S & F double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed. 23 Supply and fixing in replacement of 110mm dia uPVC soil, waste, drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement, fixed to walls complete all as specified and directed. Note- Rubber rings for pipes and fittings shall conform to IS 5382-1985. 24 S & F 110mm bore PVC (SWR) bends of any radius, complete all as specified and directed 25 SCHEDULE A PART II (E/M WORKS)Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, lamp holders, bell push bell with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed. 26 Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS-H, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 20mm dia and its fittings, including cutting chasing on wall/ceiling, including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked, including 1.5 sqmm single core PVC insulated and unsheathedFRLS-H cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dollywith and including MS flush boxes of 2 to 18 modules with inner and outer cover plates, confirming to IS 5139 of 1969 and IS 14772 of 2000 for fixing modular switch sockets for one light point (light point//fan point/bell point controlled by one one way switch complete all as specified and as directed.Notes :- (i) Switch, socket, ceiling rose, lamp holder, bell, bell push and fan regulators to be measured and paid for separately. The quoted rates are deemed to be included for providing cover plates and MS flush boxes as required at site.(ii) PVC Conduit conforming to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only and surfaces shall be make good as per existing surfaces. (iv) The concealed conduits and MS boxes as fixed against new point wiring, shall be verified by JE/Engineer-in-Charge before making good the surfaces by plastering and other finishes. 27 Description all as per Srl item No.26.00 here in before but for one 3 pin socket outletpoint 6 Amp on Independent board. 28 Description all as per Srl item No. 26.00 here in before but for one 3 pin socket outlet point 6 Amp on same board. 29 M & L for concealed point wiring complete with 2.5 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathedcable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 2.50 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :-Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted.2. Only switch, socket and fan regulators to be measured and paid seperately. 30 M & L for concealed point wiring complete with 4.0 Sqmm single core multistranded copper conductor FRLS PVC insulated and unsheathedcable 1100 volts grade drawn through and including medium grade, ISI marked, PVC conduit,medium grade ISI marked not less than 20 mm dia with accessories fixed concealed/surface type on wall/ roof/ ceiling and including provision of 4.0 sqmm single core PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor green colour as earth conitnuity conductor and connected to common earth dolly with suitable size lugs, including mild steels sunken box or pressed steel terminal box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-1) of 1969 and IS:14772:2000 with earth dolly and coated with two coat of anti corrosive paint over a coat of red oxide primer both internally and externally with and including (provision of new) modular covered plate over sunken box for housing the modular switches, socket outlets., fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for :- Note:-1 Modular metal flush / sunken box, and for modular switch/ socket cover plate & sheet are inclusive in the item rate quoted. 2. Only switch, socket and fan regulators to be measured and paid seperately. 31 Supply and fixing of Modular Socket 6Amps 2/3 Pin2 Module 230 Volts complete all as specified and directed. 32 Supply and fixing of Modular Socket 20Amps 3/5 Pin2 Module 230 Volts complete all as specified and directed. 33 Supply and fixing ofModular Switch one way 6Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. 34 Supply and fixing of Modular Switch one way 20Ampsone module ISI Marked complete all as specified and directed by Engg in Charge. 35 Supply and fixing ofCeiling rose surface backlite 65 x 20mm size three terminal ISI marked complete all as specified and directed. 36 Taking down ceiling fan /exhaust fan any capacity during execution of work and refixing the same after completion of work including necessary connection complete all as specified anddirected. 37 Supply and fixing ofModular fan Regulator electronic type100 watt 2 module complete all as specified and directed. 38 Taking down ceiling light of 35/36 watt ceiling / surface type and refixing the same after completion of work including necessary connection from ceiling rose to light complete all as specified anddirected. 39 Material and labour in replacementfor sub main wiring with two single core, 4 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulatedunsheathed copper conductor cable, drawn in and including rigid non metallic PVC conduit, medium grade, not less than 25 mm dia, ISI marked for housing cables, concealed in wall or ceiling including cutting chasing and making good, with accessories with and including one additional 4 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dolly complete all as specified and as directed. Notes- (i) Three runs of 4.0 sqmm cable and one run of concealed conduct shall be measured as one unit. (ii) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 40 Material and labour in replacement for sub main wiring with two single core, 6 sqmm, FRLS-H, 1100 volts grade, ISI marked, with multistranded, PVC insulatedunsheathed copper conductor cable, drawn in and including rigid non metallic PVC conduit, medium grade, not less than 25 mm dia, ISI marked for housing cables, concealed in wall or ceiling including cutting chasing and making good, with accessories with and including one additional 6 sqmm, PVC insulated, stranded copper conductor, FRLS-H, green colour for earth continuity conductor connected to common earth dollycomplete all as specified and as directed. Notes- (i) Three runs of 6.0 sqmm cable and one run of concealed conduct shall be measured as one unit. (ii) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. 41 Supply and fixing in replacement ofaluminium housing tube light fitting ,1x18/20 W LED 230 V, in commercial channel with powder coated CRCA sheet housing with opal diffuser for LED with LED tubelight with high efficient LED in aluminium housing with clear & milky diffuser and including connecting up with twin core twisted flexible cable copper conductor including 18/20 watt LED tube rod complete all as specified anddirected. 42 Supply and fixingin replacement LED flat panel 2 x 2 size fully difused surface/ recess mounted fitting (grid/ gypsum type)36-40 watt , 5700K,warm/cool whitewith powder coating and CRCA front cover including framewith provision ofPVC flexible copper conductor cable from ceiling rose to light fitting as in repair complete all as specified and as directed by the Engr-in-charge.Cat part No.VENUSNEO2X2PLR36WLED857G2 of make Havells or equivalentin make given in Appx B. 43 Supply and fixing in repair,LED Bldg Security Light Fittings of capacity 35 watt made up of die castaluminiumhousing with 0.9 mtr light grade GI pipe including bracket, hole and fastner for fixing the GI pipe in the wall with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection, complete all as specified and as directed by the Engineer-in-Charge.Cat part No.ENDURASUNDOWNSL25WLED765PASYBOTGIHD of make Havells or equivalentin make given in Appx B. 44 Supply and fix sheet metal MCB DB SPN8 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811825 of make Indo Asian or equivalentin make given in Appx B. 45 Supply and fix sheet metal MCB DB SPN12 way with 200 Amps rated bus bar single pole and neutral withdouble door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811828 of make Indo Asian or equivalentin make given in Appx B. 46 Supply and fixing in replacement MCB SPN 40 Amps rating ,240 volts, 50 Hz, breaking capacity 10 KAB curve, finger proof terminal bi-connect termination, label holder, 35mm^2 terminal capacity, insulated sliding shutter, large two postion dolly, ISI marked completeall as specified and directed. 47 Supply and fixing in replacement MCB SP 5-32 Amps rating ,240 volts, 50 Hz, breaking capacity 10 KAB curve, finger proof terminal bi-connect termination, label holder, 35mm^2 terminal capacity, insulated sliding shutter, large two postion dolly, ISI marked completeall as specified and directed. 48 Supply and fixing of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amps 10 KAB curve including removing old unseviceable enclouser complete all as specified and as directed. 49 Supply and fix sheet metal enclosureVertical triple pole & neutral(VTPN) IP-54 with MCCB 100 Amp, 16 KA, 415 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door duly grouted in solid block wall or on wooden board in and includinglugs/thimbles duly crimped for connectionincluding making smooth the disturbed surface including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811882 of make Indo Asian or equivalentin make given in Appx B. 50 Material and labour in replacement for earthing material and provision of new earthing complete copper plate electrode 600mm x 600mmx 3.15mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m belowground level with top edge of the earthplate not less than 1.5m belownormal groundlevel, connected to 20x3 mm copper strip earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 32mm dia (medium grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering and 32mm GIprotection pipe, funnel, wire mesh,cast iron cover andframe etc, complete, all as specified or indicated and as directed including testing on completion.Notes : (i) The quoted rate shall include the cost of earth work, GI pipe for watering, GI protection pipe, funnel, wire wesh, RCC cover, etc. complete. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.(ii) The quoted rate shall include the cost of earth pit covers to be conspicuously marked of plate with stand grouted in PCC. (iii) On testing after completion if the desired earth resistance is more than 2 ohm the earthing will be redone at no extra cost. 51 Supply and laying of LT underground cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 35 Sqmm 3.5 core and laying in trenches including disconnecting andtaking down of old unserviceable existing cable and removal complete all as specified and as directed.Note: Excavation and earth work shall be measured and paid separately. 52 Supply and laying of LT underground cable, XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 16 Sqmm 2 core and laying in trenches including disconnecting andtaking down of old unserviceable existing cable and removal complete all as specified and as directed.Note: Excavation and earth work shall be measured and paid separately. 53 Excavation in trenches in Soft/loose soil not exceeding 1.50 meter wide and not exceeding 1.5 meter in depth for foundation etc. or for laying of cables/pipes, erecting poles etc. and not exceeding 10Sqm on plan and getting out complete, all as specified and directed by Engineer-in-Charge. 54 Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick each,excavated soil in trenchescomplete as in soft/loose soil, complete, all as specified and directed by Engineer-in-Charge. 55 Removingsurplussoil/ excavated material to a distance n exc 50 m and depositing where directed at a level not exceeding 1.5m above the starting point complete, all as specified and directed by Engineer-in-Charge. 56 Supply and lay bricks, common burnt clay, sub class B, old size, laid in vertical direction to cable as cable protection complete all as specified and as directed. 57 Material and labourfor Sand cushioning to cable with a layer of sand 8 cm deep before laying the cable and 15 cmsdeep after laying the cable (punned down to 18 cms depth after laying and stretching of cable ) complete all as specified and as directed. Note:- Punned thickness 18cm shall be measured for payment purposes. 58 Supply and fixing of light grade, GI tubing, of size32mm bore, for cable protection and fixed with clamp to pole and wall with nuts and bolts complete all as specified and as directed. 59 Supply and fixing in replacement of4 inch 8mm thick PVC electrical casing caping for enclosing communication cable on wall complete all as specified and directed. 60 Note:-Amount of credit ofRs. 9318.00 for retrieved materials is mentioned in Schedule of Credit Page No. 17 of tender documents in pdf form which will be deducted offline while acceptance of tender.