BRR : 11552940 Reallocation Of Existing Pto From Petlaburz To Suitable Police Land Situated At Ptc, Amberpet, Hyderabad.-EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308). EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL MECHANICALMEANS UP TO 3M DEPTH - FOUNDATION OF BUILDING (APSS 308). CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOUNDATIONS & UNDER STONE SLAB FLOORING .(APSS NO: 402). RE-FILLING WITH USEFUL AVAILABLE EXCAVATED EARTH OTHER THAN EXPANSIVE SOILS LIKE RED EARTH AND ORDINARY GRAVEL ETC., (EXCLUDING ROCK) IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES , HIRE CHARGES OF T & P ETC., BUT EXCLUDING GST - COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310) FILLING WITH CARTED GRAVEL IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES, HIRE CHARGES OF T & P ETC., COMPLETE FOR FINISHED ITEM OF WORK. (APSS NO. 309 & 310) VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR FOOTINGS (APSS NO.403) VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND)(0.40 Cum) , COARSE AGGREGATE(0.80 Cum), WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR PEDESTALS (APSS NO.403) VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND)(0.40 Cum) , COARSE AGGREGATE(0.80 Cum), WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR PLINTH BEAMS (APSS NO.403) VRCC M-25 DESIGN MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING WEIGH BATCHER/MIXER 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT NOT LESS THAN 380 KGS/ CUM, FINE AGGREGATE (SAND)(0.40 Cum) , COARSE AGGREGATE(0.80 Cum), WATER ETC., TO SITE, ON ALL MATERIALS, ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING MACHINE MIXING, LIFTING (MANUAL),LAYING CONCRETE, VIBRATING, CURING ETC., COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., PROVIDING , FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. EXCLUDING GST AND SEIGNIORAGE CHARGES. FOR GRADE WALL (APSS NO.403) PROVIDING HYSD/TMT STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM Reinforcement Steel (HYSD/TMT) from steel Manufactureres within Telangana with min integrated installed Production Capacity of 2 Lakh MT per annum like AF Star TMT/MS Life TMT, Radha TMT, Sugna TMT FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED. RCC M - 20 NOMINAL MIX (Cement:fine aggregate: coarse aggregate) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING ( MANNUAL), LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK (APSS NO.403) FOR GROUND FLOOR LINTELS RCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING (MANUAL), LAYING CONCRETE, VIBRATING, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR SUNSHADES OF 50MM AVERAGE THICK INCLUDING DRIP COURSE OF SIZE 40MM WIDE X 20MM HEIGHT IN CEMENT MORTAR (1:4)PROP FOR GROUND FLOOR (APSS NO. 403) MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR WALLS OF 225MM THICK GROUND FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PROVIDING MASONRY WORK IN CM (1:4) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 100 X 140 MM(CLASS 5) CONFIRMING TO IS : 12894 : 2002 (FIRST REVISION) FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SEINIORAGE CHARGES, SCAFFOLDING, LIFTING (MANNUAL), CURING ETC., COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR SUPERSTRUCTURE WALLS OF 100MM THICK - GROUNDD FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE.FOR FINISHED ITEM OF WORK FOR GROUND FLOOR. (APSS NO: 901&904) FLOORING WITH Double charged / multi charged stain free full body porcelain vitrified tiles with double layer pigment of size 600 x 600 mm and thickness between 8-10 mm 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, , ETC., FOR GROUND FLOOR COMPLETE FOR FINISHED ITEM OF WORK PAINTING WITH EXTERIOR EMULSION PAINT OF APPROVED MAKE AND COLOUR TO THE EXTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 Ml OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION Etc., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,COMPLETE FOR FINISHED ITEM OF WORK IN ALL FLOORS (APSS NO:908). PAINTING TO NEW WALLS WITH THREE (3) COATS OF Synthetic Polymer luxury Plastic emulsion /solvent based lustre paint of superior grade having (VOC < 50 Gms./Lit) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR INTERIOR WALLS PROVIDING AND APPLYING SYNTHETIC PLASTER PUTTY OR EQUIVALENT PUTTY SUCH AS BIRLA WALL CARE PUTTY OR TEXTURE PAINT OR EQUIVALENT SUCH AS NCL/ SAICOAT TEXTURE PAINT OF AVERAGE 2 TO 3 MM THICKNESS OVER PLASTERED SURFACE TO PREPARE THE SURFACE EVEN AND SMOOTH AFTER THOROUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, APPLYING EMERY PAPER, SAND THE SURFACE, CLEAN & WIPE OFF LOOSE DUST, APPLYING PUTTY/ TEXTURE PAINT FILLER BY PUTTY KNIFE / MUSLIN PAD, AIR DRY FOR 2 - 3 HRS FOR THE SURFACE PREPARATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK FOR EXTERNAL WALLS - EXCLUDING COST OF ACCESS SCAFFOLDING PROVIDING DODOOING TO INTERNAL WALLS WITH GLAZED FULL BODY PORCELAIN WALL TILES OF SIZE 300 X 600 MM WITH ANY TYPE OF DESIGN TEXTURE SUCH AS MARBLE FINISH, WOODEN, BAMBOO, STONE FINISHES ETC., SCRATCH LESS, STAIN FREE AND THICKNESS BETWEEN 6-8 MM 1ST QUALITY CONFORMING TO IS:15622 - 2017, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS I ST QUALITY, SET OVER BASE COAT OF CM (1:3) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., COMPLETE , ETC., FOR GROUND FLOOR COMPLETE FOR FINISHED ITEM OF WORK, FLOORING WITH NON-SKID RED OR WHITE FULL BODY CERAMIC FLOOR TILES OF SIZE 300 X 300 MM AND THICKNESS BETWEEN 7-8 MMSET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, , ETC., FOR GROUND FLOOR COMPLETE FOR FINISHED ITEM OF WORK, . FLOORING WITH HIGH POLISHED GRANITE 16 TO 18 MM THICK UP TO 8-00 (2.43 M) OTHER THAN BLACK/ PREMIUM COLOURS OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILESETC., COMPLETE, , LABOUR CHARGES FOR DRESSING OF TILES ETC., COMPLETE FOR FINISHED ITEM OF WORK, GROUND FLOOR FULL ROUNDING THE EDGES OF GRANITE/MARBLE STONE OF ALL THICKNESS INCLUDING POLISHING INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. IN GROUND FLOOR FLOORING WITH M - 20 NOMINAL MIX (CEMENT:FINE AGGREGATE: COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, BUT EXCLUDING CENTERING, SHUTTERING. FOR DECK SLAB 100 MM THICK PROVIDING DISH FINISHED FLOORING VDF ( VACCUM DEWATERING FLOORING) TO THE CC SURFACE FOR HAVING GOOD COMPACTION OF CC SURFACE AND TO HAVE SMOOTH SURFACE OF THE ROAD INCLUDING COST AND CONVETANCE OF ALL MATERIALS, HIRE CHARGES OF DISH AND FAN, ALL INCIDENTAL AND LABOUR CHARGES ETC., COMPLETE PROVIDING SAW CUTTING JOINTS FOR FRESHLY LAID CONCRETE PAVEMENT INCLUDING ALL MATERIALS AND LABOUR CHARGES ETC COMPLETE SUPPLY OF 25MM THICK HIGH PERFORMANCE PREMOULDED EXPANSION JOINT FILLER BOARD (SILFLEX CAPACELL HD-100 OR EQUIVALENT MAKE ) PLACING THE SAME 25MM BELOW TOP OF PAVMENTS SLAB, SEALING WITH BITUMINIUS HOT SEALING COMPOUND ( GRADE A ISI)/POLYSULPHADE AT 50M INTERNAL IN CC PAVEMENT INCLUDING COST AND CONVEYANCE OF ALL MATERIALS FOR EXPANSION JOINTS CONFORMING TO MORTH SPECIFICATION NO.602- 1 RMT OF JOINT LENGTH FOR 150MM THICK SLAB MAKING PLINTH PROTECTION WITH 50MM THICK CC(1:3:6) PROP. USING 20MM HBG METAL OVER A BED OF 75MM THICK CC(1:5:10) USING 40MM HBG METAL AND THE OUTER EDGE SHALL BE LINED WITH SECOND CLASS BRICKS LAID ON EDGE AND JOINTS LAID IN CM(1:40 PROP.INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES ETC., COMPLETE FOR THE FINISHED ITEM OF WORK. PLINTH PROTECTION SHALL BE LAID WITH MINIMUM SLOPE OF 1IN 50 TOWARDS OUTER EDGE. M - 25 NOMINAL MIX (CEMENT:FINE AGGREGATE: COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) COARSE AGGREGATE, WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LAYING CONCRETE, CURING ETC.,COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK, BUT EXCLUDING CENTERING, SHUTTERING. FOR DECK SLAB.FOR FIRST FLOOR.100 MM THICK RCC M - 20 NOMINAL MIX (Cement:fine aggregate: coarse aggregate) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND), COARSE AGGREGATE, WATER ETC., TO SITE AND INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING ( MANNUAL), LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK (APSS NO.403) FOR FIRST FLOOR LINTELS RCC M-20 NOMINAL MIX (CEMENT : FINE AGGREGATE : COARSE AGGREGATE) CORRESPONDING TO TABLE 9 OF IS 456 USING 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND) , COARSE AGGREGATE, WATER ETC., ALL INCIDENTAL, OPERATIONAL AND LABOUR CHARGES SUCH AS MACHINE MIXING, LIFTING (MANUAL), LAYING CONCRETE, VIBRATING, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE AND PROVIDING CENTERING USING CASURINA BALLIES, BAMBOOS, WOODEN REAPERS, RUNNERS, WOOD POSTS, WALL PLATES, STEEL CENTERING PLATES ETC., FOR UNSUPPORTED HIEGHT OF 3.66M BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR SUNSHADES OF 50MM AVERAGE THICK INCLUDING DRIP COURSE OF SIZE 40MM WIDE X 20MM HEIGHT IN CEMENT MORTAR (1:4)PROP FOR FIRST FLOOR (APSS NO. 403) PROVIDING HYSD/TMT STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER Fe 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM Reinforcement Steel (HYSD/TMT) from steel Manufactureres within Telangana with min integrated installed Production Capacity of 2 Lakh MT per annum like AF Star TMT/MS Life TMT, Radha TMT, Sugna TMT FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING ETC., EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED. MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR WALLS OF 225MM THICK FIRST FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PROVIDING MASONRY WORK IN CM (1:4) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 100 X 140 MM(CLASS 5) CONFIRMING TO IS : 12894 : 2002 (FIRST REVISION) FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SEINIORAGE CHARGES, SCAFFOLDING, LIFTING (MANNUAL), CURING ETC., COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR SUPERSTRUCTURE WALLS OF 100MM THICK - FIRST FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE.FOR FINISHED ITEM OF WORK. (APSS NO: 901&904) PAINTING WITH EXTERIOR EMULSION PAINT OF APPROVED MAKE AND COLOUR TO THE EXTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 Ml OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION Etc., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,COMPLETE FOR FINISHED ITEM OF WORK IN ALL FLOORS (APSS NO:908). PROVIDING AND APPLYING SYNTHETIC PLASTER PUTTY OR EQUIVALENT PUTTY SUCH AS BIRLA WALL CARE PUTTY OR TEXTURE PAINT OR EQUIVALENT SUCH AS NCL/ SAICOAT TEXTURE PAINT OF AVERAGE 2 TO 3 MM THICKNESS OVER PLASTERED SURFACE TO PREPARE THE SURFACE EVEN AND SMOOTH AFTER THOROUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, APPLYING EMERY PAPER, SAND THE SURFACE, CLEAN & WIPE OFF LOOSE DUST, APPLYING PUTTY/ TEXTURE PAINT FILLER BY PUTTY KNIFE / MUSLIN PAD, AIR DRY FOR 2 - 3 HRS FOR THE SURFACE PREPARATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK FOR EXTERNAL WALLS - EXCLUDING COST OF ACCESS SCAFFOLDING PAINTING TO NEW WALLS WITH THREE (3) COATS OF Synthetic Polymer luxury Plastic emulsion /solvent based lustre paint of superior grade having (VOC < 50 Gms./Lit) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK FLOORING WITH DOUBLE CHARGED / MULTI CHARGED STAIN FREE FULL BODY PORCELAIN VITRIFIED TILES WITH DOUBLE LAYER PIGMENT OF SIZE 600 X 600 MM AND THICKNESS BETWEEN 8-10 MM 1ST QUALITY CONFORMING TO IS:13711, IS:13712, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS, SET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, , ETC., COMPLETE FOR FINISHED ITEM OF WORK PROVIDING DODOOING TO INTERNAL WALLS WITH GLAZED FULL BODY PORCELAIN WALL TILES OF SIZE 300 X 600 MM WITH ANY TYPE OF DESIGN TEXTURE SUCH AS MARBLE FINISH, WOODEN, BAMBOO, STONE FINISHES ETC., SCRATCH LESS, STAIN FREE AND THICKNESS BETWEEN 6-8 MM 1ST QUALITY CONFORMING TO IS:15622 - 2017, IS:13630 (PARTS 1 TO 15) OF ANY COLOUR AND FINISH IN ALL SHADES AND DESIGNS I ST QUALITY, SET OVER BASE COAT OF CM (1:3) 12 MM THICK WITH CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD AT THE RATE OF 3.30 KGS PER SQM AND JOINTED WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE TILES, CEMENT, SAND AND WATER ETC., COMPLETE , ETC., COMPLETE FOR FINISHED ITEM OF WORK, FLOORING WITH NON-SKID RED OR WHITE FULL BODY CERAMIC FLOOR TILES OF SIZE 300 X 300 MM AND THICKNESS BETWEEN 7-8 MMSET OVER BASE COAT OF CEMENT MORTAR (1:8), 12 MM THICK OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE TO FULL DEPTH MIXED WITH PIGMENT OF MATCHING SHADE, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILES ETC., COMPLETE, , ETC., COMPLETE FOR FINISHED ITEM OF WORK, . Providing skirting to internal walls to 15 cm height / risers of steps glazed red or white full body ceramic wall tiles of size 300 x 600 mm and thickness between 6-8 mm length equal to flooring stones, set over base coat of CM (1:3) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete , etc., complete for finished item of work FLOORING WITH HIGH POLISHED GRANITE 16 TO 18 MM THICK UP TO 8-00 (2.43 M) OTHER THAN BLACK/ PREMIUM COLOURS OVER CC BED ALREADY LAID OR RCC ROOF SLAB, INCLUDING NEAT CEMENT SLURRY OF HONEY LIKE CONSISTENCY SPREAD @ 3.3.KGS PER SQM & JOINTED NEATLY WITH WHITE CEMENT PASTE MIXED WITH PIGMENT OF MATCHING SHADE TO FULL DEPTH, INCLUDING COST OF ALL MATERIALS LIKE CEMENT, SAND WATER AND TILESETC., COMPLETE, , LABOUR CHARGES FOR DRESSING OF TILES ETC., COMPLETE FOR FINISHED ITEM OF WORK, FIRST FLOOR FULL ROUNDING THE EDGES OF GRANITE/MARBLE STONE OF ALL THICKNESS INCLUDING POLISHING INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. IN FIRST FLOOR PROVIDING IMPERVIOUS COAT TO EXPOSED RCC ROOF SLAB SURFACE WITH CM(1:3), 20MM THICK WITH 1KG OF WATER PROOF COMPOUND PER BAG OF CEMENT LAID OVER ROOF WHEN IT IS GREEN INCLUDING COST OF ALL MATERIALS, INCLUDING CONVEYANCE CHARGES OF MATERIALS AND INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES FOR MIXING MORTAR, LAYING, RENDERING SMOOTH AND THREAD LINING, CURING, ROUNDING OFF JUNCTIONS OF WALL AND SLAB ETC,, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR FIRST FLOOR MASONRY WORK IN CM (1:6) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 225 X 140 MM FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SCAFFOLDING AND CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR WALLS OF 225MM THICK SECOND FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PROVIDING MASONRY WORK IN CM (1:4) PROP WITH FLYASH CEMENT SOLID BLOCKS OF SIZE 290 X 100 X 140 MM(CLASS 5) CONFIRMING TO IS : 12894 : 2002 (SECOND REVISION) FOR MANUFACTURING OF FLYASH SOLID BLOCKS USING FLYASH OF 80 KGS, CEMENT OF 15 KGS. GYPSUM OF 5 KGS. AND STONE DUST INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, LABOUR CHARGES, SEINIORAGE CHARGES, SCAFFOLDING, LIFTING (MANNUAL), CURING ETC., COMPLETE WITH A COMPRESIVE STRENGTH NOT LESSTHAN 50 KG/SQM FOR SUPERSTRUCTURE WALLS OF 100MM THICK - THIRD FLOOR FOR FINISHED ITEM OF WORK(APSS NO. 501&504) PLASTERING TO SUPERSTRUCTURE 12 MM THICK IN TWO COATS, WITH A BASE COAT OF 8 MM THICK IN CM (1:6) PROP. AND TOP COAT OF 4 MM THICK IN CM (1:4) PROP. with sponze finishing, INCLUDING MAKING GROOVES, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING ( MANUAL) CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE.FOR FINISHED ITEM OF WORK. (APSS NO: 901&904) PAINTING WITH EXTERIOR EMULSION PAINT OF APPROVED MAKE AND COLOUR TO THE EXTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750 Ml OF WATER WITHIN AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS OVER 1COAT OF ASIAN EXTERIOR WALL PRIMER BY DILUTING 1LIT. OF PRIMER WITH 1LIT. OF WATER (TOTAL 3 COATS) WITH SURFACE PREPARATION Etc., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,COMPLETE FOR FINISHED ITEM OF WORK IN ALL FLOORS (APSS NO:908). PAINTING TO NEW WALLS WITH THREE (3) COATS OF Synthetic Polymer luxury Plastic emulsion /solvent based lustre paint of superior grade having (VOC < 50 Gms./Lit) OF APPROVED BRAND AND SHADE (ASIAN /BERGER /NEROLAC /SAICOAT /INDOCEM OR EUIVALENT) OVER ONE COAT OF PRIMER OF APP BRAND AFTER THOUROULY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDER MATERIALS INCLUDING COST OF ALL MATERIALS TO THE INTERIOR FACES OF WALLS AS DIECTED 2COATS BY DILUTING 1LIT OF EMULSION PAINT WITH A MAXIMUM 750ML OF WATER WITH AN INTERVAL OF NOT LESS THAN 6 HOURS BETWEEN TWO COATS (TOTAL3 COATS) WITH SURFACE PREPARATION ETC., AS PER STANDARD SPECIFICATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, BRUSHES, LABOUR CHARGES, CURING, SCAFFOLDING LIFTING(MANUAL) AND ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK PROVIDING AND APPLYING SYNTHETIC PLASTER PUTTY OR EQUIVALENT PUTTY SUCH AS BIRLA WALL CARE PUTTY OR TEXTURE PAINT OR EQUIVALENT SUCH AS NCL/ SAICOAT TEXTURE PAINT OF AVERAGE 2 TO 3 MM THICKNESS OVER PLASTERED SURFACE TO PREPARE THE SURFACE EVEN AND SMOOTH AFTER THOROUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, APPLYING EMERY PAPER, SAND THE SURFACE, CLEAN & WIPE OFF LOOSE DUST, APPLYING PUTTY/ TEXTURE PAINT FILLER BY PUTTY KNIFE / MUSLIN PAD, AIR DRY FOR 2 - 3 HRS FOR THE SURFACE PREPARATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO WORK SITE AND ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC. COMPLETE FOR FINISHED ITEM OF WORK FOR EXTERNAL WALLS - EXCLUDING COST OF ACCESS SCAFFOLDING SUPPLY AND FIXING GYP BOARD SUSPENDED REGULAR SINGLE LAYER FALSE CEILING (GS-MFSC-4.1 AS PER INDIA GYPSUM) USING 12.50 MM THICK GYP BOARD CONFORMING TO IS 2095-1982 FIXING TO GYP STEEL GI PERIMETER CHANNELS OF SIZE 20 X 27 X 30 MM (WEB) OF 0.55 MM THICK ALONG THE PERIMETER OF CEILING SCREW FIXED TO BRICK WORK / PARTITION AT 610 MM C/C AND SUSPENDING THE FRAME WORK USING INTERMEDIATE CHANNELS (45 X 15 X 15 X 0.90 MM) FROM SOFFIT AT 1220 MM C/C WITH CEILING ANGLE (25 X 10 X 0.55 MM) FIXED WITH GI CLEAT AND STEEL EXPANSION FASTENERS & CONNECTING CLIP TO THE CEILING CHANNELS (WITH KNURLED WEB OF 51.50 X 26 X 10.50 X 0.55 MM) FIXED IN DIECTION PERPENDICULAR TO THE INTERMEDIATE CHANNEL AT 457 MM C/C AND FIXING THE 12.50 MM DRYWALL SCEWS AT 230 MM C/C & JOINTING, FIXING USING JOINT COMPOUND AND PAPER TAPE TO HAVE A FLUSH LOOK INCLUDING FILLING THE TAPPERED & SQUARE EDGES WITH JOINTING COMPOUND, TWO COATS OF DRYWALL TOPCOAT, BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK AS PER INDIA GYPSUM LTD., SPECIFICATION. PROVIDING, SUPPLYING & FIXING OF TOP HUNG VENTILATOR WITH EXHAUST FAN PROVISION MADE OUT OF MULTI CHAMBERED UPVC SECTIONS WITH TPV GASKET FOR SASH & GLAZING BEAD SHALL BE COEXTRUDED WITH GREY COLOUR SOFT PVC AND REINFORCED WITH GALVANIZED IRON PROFILES THROUGHOUT THE WINDOW. THE OUTER FRAME HAVING A OVERALL SIZE OF 60MM X 55 MM X 2.40 MM WITH REINFORCEMENT OF 1 MM THICKNESS, MULLION WITH OVERALL SIZE OF 74 MM X 60 MM X 2.40 MM WITH REINFORCEMENT OF 1 MM THICKNESS AND SASH WITH OVERALL SIZE OF 75 MM X 60 MM X 2.40 MM WITH REINFORCEMENT OF 1.0/1.2 MM THICKNESS. (COMPOSITION OF PROFILE SHALL CONSISTS A MINIMUM OF 5.5 PHR OF TIO2 AND NOT MORE THAN 12 PHR OF CACO3 FOR EVERY 100 PARTS OF PVC RESIN).GLAZING BEAD FOR FIXING OF GLASS SHALL BE OF SIZE 34 X 20 MM COEXTRUDED WITH SOFT PVC GASKET. VENTILATOR SHALL BE PROVIDED WITH 4.5 MM PIN HEAD GLASS, STANDARD HARDWARE, SINGLE POINT LOCKING USING COCKSPUR HANDLE AND FRICTION STAYS. WALL THICKNESS OF FRAME, MULLION AND SASH SHALL BE 2.4 MM., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, ACCESSORIES, LABOUR CHARGES FOR TRANSPORTATION, ERECTION AT SITE COMPLETE FOR FINISHED ITEM OF WORK, BUT EXCLUDING GST SUPPLYING AND FIXING OF UNPLASTICISED POLY VINYL CHLORIDE (UPVC) 3 TRACK SLIDING WINDOWS WITH MESH SHUTTER – (2-GLASS SHUTTERS AND 1-MESH SHUTTER) DULY MANUFACTURED USING UPVC REINFORCED PROFILES (COMPOSITION OF PROFILE SHALL CONSISTS A MINIMUM OF 5.5 PHR OF TIO2 AND NOT MORE THAN 12PHR OF CACO3 FOR EVERY 100 PARTS OF PVC RESIN) OF (94MMX45MM)/(80MMX52MM) X 2.20 MM FOR OUTER FRAMES, (58 MM X 39 MM)/(54 MM X 38 MM) X 2.20 MM FOR SLIDING SHUTTER FRAMES CAPABLE OF MOUNTING SINGLE GLAZING SYSTEM STRUCTURALLY REINFORCED WITH HOT DIP GALVANIZED UP TO 50 MICRONS OF MINIMUM THICKNESS OF 1.0/1.2MM PREFABRICATED & WELDED THROUGH FUSION WELDING. THE WINDOW SASH SHALL BE FITTED WITH 5 MM THICK CLEAR FLOAT GLASS OF REPUTED MAKE AND MESH SHUTTER FRAME SHALL BE (42MMX25MM) / (52MMX21.5MM)X2.0MM FITTED WITH VINYL COATED FIBRE MESH-ON ROLLERS/PULLEY DULY FIXED WITH GREY COLOUR TPV GASKET FOR SASH & GLAZING BEAD SHALL BE CO-EXTRUDED WITH GREY COLOUR SOFT PVC. SYSTEM SHALL HAVE SINGLE POINT LOCKING WITH TOUCH LOCK AND THE SYSTEM IS TO BE INSTALLED AT THE SITE USING ANCHOR FASTENERS, SILICON RUBBER SEALANT, EASY GLAZING/DEGLAZING AT SITE ETC., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS, ACCESSORIES, LABOUR CHARGES FOR TRANSPORTATION, ERECTION AT SITE COMPLETE FOR FINISHED ITEM OFWORK. BUT EXCLUDING GST INTERNAL DOOR (SINGLE SHUTTER): 0.9 X2.10M: SUPPLYING, POSITIONING AND FIXING OF ISI MARK, STANDARD MAKE, FLUSH DOOR SHUTTER OF 35 MM THICK WITH TEAK VENEER ONE SIDE AND COMMERCIAL PLY ON ANOTHER FACE INCLUDING DOOR FRAME MADE WITH MEDIUM TEAK WOOD SCANTLING OF SIZE 125 MM X 75 MM, 6 NOS. OF MS Z HOLD FASTS OF SIZE 230 X 40 X 3 MM, 3 NOS. OF 125 MM BUTT HINGES, 2NOS. 150 MM LONG DOOR HANDLES, 1 NO. ALDROP OF SIZE 250 MM LONG, 1 NO. 200 MM LONG TOWER BOLTS, 1 NO. DOOR STOPPER WITH BOLTS, NUTS, NF SCREWS, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR MAKING THE FRAME AND FIXING FRAME AND SHUTTER, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK. (ALL FITTINGS AND FIXTURES SHOULD BE OF STAINLESS STEEL, ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE). (APSS NO: 1001&1002). MAIN DOOR (DOUBLE SHUTTER): 1.20 X2.10M: SUPPLYING, POSITIONING AND FIXING OF ISI MARK, STANDARD MAKE, FLUSH DOOR SHUTTER OF 35 MM THICK WITH TEAK VENEER ONE SIDE AND COMMERCIAL PLY ON ANOTHER FACE INCLUDING DOOR FRAME MADE WITH MEDIUM TEAK WOOD SCANTLING OF SIZE 125 MM X 75 MM, 6 NOS. OF MS Z HOLD FASTS OF SIZE 230 X 40 X 3 MM, 6 NOS. OF 125 MM BUTT HINGES, 4NOS. 150 MM LONG DOOR HANDLES, 2 NO. ALDROP OF SIZE 250 MM LONG, 2 NO. 200 MM LONG TOWER BOLTS, 2 NO. DOOR STOPPER WITH BOLTS, NUTS, NF SCREWS, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES FOR MAKING THE FRAME AND FIXING FRAME AND SHUTTER, MINOR EXTRA FIXTURES REQUIRED IF ANY AS DIRECTED BY THE ENGINEER-IN-CHRGE OF THE WORK COMPLETE FOR FINISHED ITEM OF WORK. (ALL FITTINGS AND FIXTURES SHOULD BE OF STAINLESS STEEL ISI MARK, GOT APPROVED BY THE ENGINEER-IN-CHARGE). (APSS NO: 1001&1002). SUPPLY & FIXING OF ROLLING SHUTTER MADE OF 80 X 1.25 MM MACHINE ROLLED CRCA LATHS, INTERLOCKED TOGETHER THROUGH THEIR ENTIRE LENGTH AND JOINTED TOGETHER AT THE ENDS BY END-LOCKS, MOUNTED ON SPECIALLY DESIGNED PIPE SHAFT OF 50MM DIAMETER NOMINAL BORE MS B CLASS PIPE WITH BRACKETS, PLATES, GUIDE CHANNELS, STOPPERS, BOTTOM LOCKING PLATES AND ARRANGEMENTS FOR INSIDE & OUTSIDE LOCKING WITH PUSH-PULL OPERATIONS INCLUDING COST OF HOOD COVER AND SPRINGS COMPLETE, PAINTED WITH ONE COAT OF APPROVED STEEL PRIMER, LOCKS, BALL BEARINGS, ALL ACCESSORIES ETC COMPLETE FOR FINISHED ITEM OF WORK AS PER SPECIAL SPEC: 1108 ( TBSC-E.I-01 ) SUPPLYING MS STRUCTURAL STEEL WORKS LIKE HEAVY STEEL WORKS LIKE TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS INCLUDING COST OF WELDING RODS, POWER CHARGES, FOR ERECTING & FIXING ALL STRUCTURAL STEEL WORKS LIKE HEAVY IRON GRILLS, TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS ERECTING IN POSITION AND FIXING BY USING CHAIN PULLEY BLOCKS, DEREK POLE ARRANGEMENTS AND CRANES ETC., COMPLETE IN POSITION ETC COMPLETE FOR ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.STUBES OF ALL SIZES SUPPLYING AND FIXING MS GRILLS FOR WINDOWS/VENTILATORS OF ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK M.S. SQUARE BARS OF ALL SIZES PAINTING TO NEW IRON WORK TWO COATS WITH SYNTHETIC ENAMEL PAINT OVER ONE COAT OF PRIMER OF APPROVED BRAND AND SHADE TOTAL 3 COATS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, ALL INCIDENTAL, OPERATIONAL & LABOUR CHARGES FOR PREPARING AND CLEANING THE SURFACE OF DIRT WITH SOAP AND BRUSHES, INCLUDING PUTTY, ETC., COMPLETE FOR FINISHED ITEM OF WORK EXCLUDING GST. (APSS NO.1201, 1207, 1212). ROOFING: - ROOFING WILL BE PROVIDED WITH 0.5MM THICK GALVANIZED / PRE PAINTED G.I. PROFILED SHEETS FIXED TO THE PURLINS WITH 14 SIZE SELF DRILLING SCREWS WITH NEOPRENE WASHER. SIDE LAPS ARE STITCHED WITH SELF TAPPING / DRILLING SCREWS. END LAPS ARE TO BE SEALED WITH 25X3 MM BUTYL TAPE. THE SHEETS ARE PROVIDED WITH ANTI CAPILLARY GROVE. PROVIDING AND APPLYING SYNTHETIC PLASTER PUTTY OR EQUIVALENT PUTTY SUCH AS BIRLA WALL CARE PUTTY OF AVERAGE 1 TO 2 MM THICK OVER PLASTERED SURFACE TO PREPARE THE SURFACE EVEN AND SMOOTH AFTER THOROUGHLY BRUSHING THE SURFACE TO REMOVE ALL DIRT AND REMAINS OF LOOSE POWDERED MATERIALS, APPLYING EMERY PAPER, SAND THE SURFACE, CLEAN & WIPE OFF LOOSE DUST, APPLYING, KNIFING PASTE FILLER BY PUTTY KNIFE / MUSLIN PAD, AIR DRY FOR 2-3 HRS., SAND WITH 180 AND 320 NO. EMERY PAPER FOR THE SURFACE PREPARATION INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, ALL OPERATIONAL, INCIDENTAL, LABOUR CHARGES ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR INTERNAL WALLS. SUPPLYING STRUCTURAL STEEL HOLLOW SQUARE &RECTANGULAR SECTIONS OF 355 MPA GRADE CONFORMING TO IS 4923-1997 INCLUDING LOADING, TRANSPORTATION AND UNLOADING CHARGES INCLUDING COST OF WELDING RODS, POWER CHARGES, FOR ERECTING & FIXING ALL STRUCTURAL STEEL WORKS LIKE HEAVY IRON GRILLS, TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS ERECTING IN POSITION AND FIXING BY USING CHAIN PULLEY BLOCKS, DEREK POLE ARRANGEMENTS AND CRANES ETC., COMPLETE IN POSITION ETC COMPLETE FOR ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK. SUPPLYING OF GALVANIZED STEEL OF ALL SIZES INCLUDING LOADING, TRANSPORTATION AND UNLOADING CHARGES INCLUDING COST OF WELDING RODS, POWER CHARGES, FOR ERECTING & FIXING ALL STRUCTURAL STEEL WORKS LIKE HEAVY IRON GRILLS, TRUSSES, STANCHIONS, HEAVY BEAMS AND GIRDERS ERECTING IN POSITION AND FIXING BY USING CHAIN PULLEY BLOCKS, DEREK POLE ARRANGEMENTS AND CRANES ETC., COMPLETE IN POSITION ETC COMPLETE FOR ALL SIZES AS DIRECTED BY THE ENGINEER-IN- CHARGE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES FOR FABRICATION, FIXING ETC., COMPLETE FOR THE FINISHED ITEM OF WORK. FOR PURLINS SUPPLY AND FIXING OF TURBO VENTILATORS MADE OF STAINLESS STEEL OF 600MM DIA AND THE BASE IS MADE OF GRP SHEET AND FIXED TO THE ROOFING INCLUDING COST AND CONVENYANCE OF ALL NECESSARY MATERIALS, LABOUR, LIFTING, TRANSPORTATION ETC EXCL GST COMPLETE FOR FINISHED ITEM OF WORK SUPPLY OF ROOF ACCESSORIES MEDIUM SIZE: RIDGE, BARGE CAP, CORNER TRIM, L-FLASHING, DOWN PIPES, GUTTER ETC., WITH 0.50MM THICK, WIDTH: 0.585, LENGTH: MAXIMUM 2½ METERS Supply and Fixing of Sky Lights -made of 1.5mm thick FRP including fixing in roofing etc., complete Supply and Fixing of Galvanized Roofing Deck sheets with 0.80mm -2mm thickness, Coating: Zinc coating Z125 / Z275/ Z 500 GSM. Yield Strength: E250. crest to crest width 130 mm length 12 metres : profile width 982mm and profile depth 44mm CR steel as per IS-513 HR steel as per IS 1079 and Galvanised Steel as per IS 277 Roofing: - Roofing will be provided with 0.5mm thick galvanized / pre painted G.I. profiled sheets fixed to the purlins with 14 size self drilling screws with neoprene washer. The bottom of the sheets are insulated with Rock Wool material including cost and conveyance all materials to site etc., complete. Color : Silver PROVIDING SAND BLAST PAINTING TO THE M.S & G.I STRUCTURAL ITEMS INCLUDING COST OF ALL MATERIALS, LABOUR ETC., COMPLETE FOR FINISHED ITEM OF WORK. COLOR : AS DESIRED BY THE USER SUPPLY AND FIXING OF 22.20MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2 TO 2) ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLY AND FIXING OF 28.60MM OD PIPE - SDR 11 ASHIRVAD / ASTRAL FLOW GUARD OR EQUIVALENT CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2 TO 2) ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLYING AND FIXING 15mm brass Bib Tap cp finish - Indian make heavy duty full turn 300gms AS DIRECTED BY THE ENGINEER-IN-CHARGE, INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLYING AND FIXING GM GATE (PEET) VALVES - 25 MM NB SIZEINDIAN MAKE HEAVY DUTY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK SUPPLYING AND FIXING GM GATE (PEET) VALVES - 20 MM NB SIZEINDIAN MAKE HEAVY DUTY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE AND LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK SUPPLYING AND FIXING 76.2MM (3) DIA UV RESISTANT UPVC SWR NAHANI TRAP WITH JALI OF APPROVED ISI BRAND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLYING AND LAYING 75 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5 INTERVALS AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS, PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK.FOR GROUND FLOOR SUPPLY AND FIXING IN POSITION EUROPEAN TYPE WATER CLOSET OF BEST INDIAN MAKE WHITE GLAZED WITH 100 MM P TRAP, PLASTIC SEAT AND LID FOR EUROPEAN WATER CLOSET AND BUFFERS AS PER IS 2548-1963 AND PROVIDING PVC LOW LEVEL FLUSHING SYSTEM OF 8 LITRES CAPACITYOF PARRYWARE SLIMLINE (WHITE) WITH INTERNAL COMPONENTS AND SHORT BEND, 12.70 MM PVC CONNECTION WITH BRASS UNION NUTS C.P COATED, INCLUDING CUTTING THE WALLS AND FLOORS AND MAKING GOOD THE SAME, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., COMPLETE. SUPPLYING AND FIXING INDIAN MAKE FLAT BACK WHITE GLAZED WASH HAND BASIN (HSW/PARRYWARE/NEYCER) IST QUALITY CONFIRMING TO IS: 2556-PART-4 :1972 OF SIZE 550 X 400MM SINGLE C.P. PILLAR COCK AS APPROVED BY EXECUTIVE ENGINEER WITH WASTE FITTINGS LIKE RUBBER PLUG, CHAIN, 32MM NOMINAL SIZE C.P. FITTING WITH PARALLEL PIPE THREAD CONFIRMING TO IS : 2963-1979 AND FITTED WITH 15MM NOMINAL BORE CHROMIUM PLATED PILLAR TAP OF 1ST QUALITY INDIAN MAKE 300GRAMS SEICO/ESSO OR EQUIVALENT COMPLETE WITH STANDARD CI BRACKETS INCLUDING WOODEN BLOCK AND PAINTING TO ALL IRON FITTINGS WITH 2 COATS OF SYNTHETIC ENAMEL PAINT OF APPROVED COLOUR AND MAKE INCLUDING CUTTING THE WALLS WHEREVER NECESSARY AND MAKING THE SAME GOOD FOR FINISHED ITEM OF WORK. SUPPLYING & FIXING WHITE GLAZED FLAT BACK HALF STALL URINALS 1ST QUALITY CONFORMING TO IS:2556-1995 WITH STANDARD C.P. SPREADER FIXED WITH SCREWS COMPLETE INDIAN MAKE : 590 X375 X 390 MM FIXED WITH SCREWS COMPLETE INDIAN MAKE FIXED WITH SCREWS COMPLETRE INDIAN MAKE INCLUDING 12.70 MM PVC CONNECTION WITH BRASS UNION NUTS C.P COATED, 38.10 MM C.P WASTE COUPLING, 38.10 MM PVC SOLID WASTE PIPE OUTLET, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE.(TBSP-E.VII-03) SUPPLYING AND FIXING BEST INDIAN MAKE 609.6X457.2mm T.V SHAPE MIRROR WITH PLASTIC FRAME MIRROR INCLUDING WOODEN BLOCKS, SCREWS ETC., INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK SUPPLYING AND LAYING 110 MM DIA SINGLE SOCKET PVC / SWR PIPES OF APPROVED MAKE OF 4 Kg/cm2 CONFIRMING TO IS:13592-1992, WITH NECESSARY UPVC PIPE CLIPS @ 5 INTERVALS AND JOINTED WITH SOLVENT CEMENT INCLUDING CUTTING OF WALLS AND FLOORS AND MAKING THE SAME GOOD, AND LABOUR CHARGES FOR LAYING, FIXING, AND COMMISSIONING THE PVC PIPES INCLUDING COUPLERS/ BENDS/TEES ETC., INCLUDING FIXING NECCESSARY FITTINGS LIKE BENDS PLUGS, COUPLERS, JUNCTIONS, TEES ETC., WITH SOLVENT JOINTING AS PER STANDARDS,INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLYING AND FIXING NP SOAP DISH HEAVY TYPE WITH NP SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC.,BUT EXCLUDING GST,COMPLETE FOR FINISHED ITEM OF WORK. SUPPLYING AND FIXING 19.04 MM DIA, 609.60 MM LONG ALUMINUM ANODISED TOWEL ROD WITH BRACKETS AND SCREWS INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK . SUPPLYING AND FIXING OF 150MMX100MM SWG GULLY TRAP CONFIRMING TO ISI 651 & 4127 WITH CI GRATING AND CONSTRUCTION OF BRICK MASONRY INTERMEDIATE CHAMBER OF SIZE 20X14X12 IN CM (1:6) OVER CC (1:5:10) PROP. BED OF SIZE 20X14X4 AND PLASTERING WITH 12MM THICK IN CM (1:4) PROP. BOTH INSIDE AND OUTSIDE SURFACES AND FITTED WITH 9X12 (230X305MM) RCC (1:11/2:3) 1 1/2 THICK COVER INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK COMPLETE. CONSTRUCTING 1-6 X 1-6 BRICK MASONARY INSPECTION CHAMBER WITH CM (1:6) PROP. USING FLY ASH BRICKS OF 225MM THICK , AND FITTED WITH 457.2 X 457.2 MM (1-6 X 1-6) RCC COVER UP TO A DEPTH OF 914.4 MM (3-0) AND LAYING CEMENT CONCRETE (1:4:8) 150 MM THICK USING 40 MM HBG METAL AND PCC (1:2:4) BENCHING AND CHANNEL 100 MM THICK INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, SAND, BRICKS, WATER ETC.,TO SITE ,COST OF LABOUR CHARGES LIKE MIXING CEMENT MORTAR, CONSTUCTING MASONARY, LIFT CHARGES, CURING ETC., COMPLETE INCLUDING COST OF STEEL AND ITS FABRICATION, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, FOR FINISHED ITEM OF WORK AS PER STANDARD SPECIFICATION PROVIDING AND PLACING ON TERRACE POLYTHELENE WATER STORAGE TANKS (AT ALL FLOOR LEVELS) DOUBLE LAYER APPROVED BRAND AND MNUFACTURE WITH COVER AND SUITABLE LOCKING ARRANGEMENTS MAKING NECESSARY HOLES FOR INLET & OUTLETS AND OVERFLOW PIPES BUT WITHOUT FITTINGS & BASE SUPPORT FOR TANKS, MAKING GOOD THE SAME TO ENSURE LEAK PROOF WITH AN APPROPRIATE MASONARY PLATFORM INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR ETC.,BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK AS DIRECTED BY THE ENGINEER -IN- CHARGE SUPPLY AND FIXING OF 28.60 MM OD PIPE - SDR 13.5ASHIRVAD / ASTRAL OR EQUIVALENT PREMIUM CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2 TO 2) ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLY AND FIXING OF 22.20MM OD PIPE - SDR 13.5ASHIRVAD / ASTRAL OR EQUIVALENT PREMIUM CPVC PIPES AND FITTINGS TO MEET THE REQUIREMENTS OF ASTM-D 2846 AND ARE PRODUCED IN CTS (COPPER TUBE SIZES 1/2 TO 2) ASHIRVAD FLOWGUARDS SDR 11 MADE FROM IDETICAL CPVC COMPOUNDS HAVING THE SAME PHYSICAL PROPERTIES FOR HOT AND COLD WATER (IS 15778-2007) INCLUDING COST AND CONVEYANCE OF PIPE & ITS FITTINGS AND ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST, COMPLETE FOR FINISHED ITEM OF WORK. DRILLING OF BORE WELL BY DOWN THE HOLE HAMMER (DTH) DRILLING TO A FINISHED DIA OF 165MM (61/2”) IN ALL FORMATIONS SUITABLE FOR DOWN THE HOLE HAMMER DRILLING SUCH AS MEDIUM ROCKS TO HARD ROCKS FORMATION ETC., AND REMAINING BORE TO SUIT INSERTION O CASING PIPE, CAPS AND OTHER RELEVANT MATERIALS REQUIRED UPTO THE DEPTH AS DIRECTED BY THE DEPARTMENT (BUT EXCLUDING COST OF CASING PIPE, COUPLINGS, CAPS) AND TRANSPORTATION OF DRILLING MACHINE INCLUDING OF SUPPORTING VEHICLES FROM PLACE TO PLACE AND INCLUDING BORE DEVELOPMENT (FLUShING THE BORE WELL AT AN AVERAGE PRESSURE OF 100 PSI) COST OF YEILD CHARGES Crew CHARGES COST OF CONSUMABLES, TRANSPORATION CHARGES OR OTHER CHARGES REQUIRED IN FIXING OF PIPES ASSEMBLING OF DEPTH AS STIPULATED IN THE TECHINCAL CoNDITIONS OF PR DEPARTMENT AND THE ENTIRE WORK SHOULD BE CARRIED OUT AS PER IS 2800 PARTS I & III 1979 - BUT EXCLUDING GST SUPPLY AND FIXING OF 7 DIA UPVC CASING PIPES(PRESSURE OF 6KG/CM2) CONFORMING TO IS 4985/1988 AS DIRECTED BY THE DEPARTMENT INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE LABOUR CHARGES AND TRANSPORATION CHARGES ETC., BUT EXCLUDING GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLY AND FIXING OF PVC CAP SUITABLE FOR 7DIA PVC CASING INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE LABOUR CHARGES AND TRANSPORATION CHARGES ETC., BUT EXCLUDING GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. SUPPLY OF 3 CORE 4.0 SQMM FLAT COPPER CABLE OF ISI FOR SUBMERSIBLE MOTORS. MAKES : FINOLEX / RR KABEL / HAVELLS / KEI / LK (L&T) / PAWANCAB. COMPLETE FOR FINISHED ITEM OF WORK - EXCLUDING GST SUPPLY AND TRANSPORTATION OF STAR RATED 5.00 HP 12-16 STAGE THREE PHASE ISI SUBMERSIBLE MOTOR PUMPSET SUITABLE FOR 6 BORE WELL. COMPLETE FOR FINISHED ITEM OF WORK - EXCLUDING GST MAKES: TEXMO / CRI / KSB / ARYENVARSHA / LUBI / FALCON MANUFACTURE, SUPPLY, & DELIVERY OF HIGH DENSITY POLYETHYLENE PIPES (PE-100 GRADE) OF - OD 32 mm - SDR 11 - 12.5 kg/sqcm (SDR 11)FOR WATER SUPPLY CONFORMING TO IS 4984-2016 INCLUDING TRANSPORTATION TO ANY WHERE IN T.G, BUT EXCLUDING GST AND SPECIALS ETC., COMPLETE. (SUPPLY UPTO 90 MM DIA IN COIL & ABOVE 90 MM DIA STRIGHT LENGTH IN 6 M.) LOWERING, LAYING, JOINTING OF PVC/HDPE/MDPE PIPES AS PER BIS NO.7634 PART-III/75 FOR PVC AND BIS NO.7634 PART-II/75 FOR HDPE PIPES INCLUDING EARTH WORK EXCAVATION, TESTING TO HYDRAULIC TEST PRESSURE INCLUDING COST OF WATER WITH A WATER LEAD OF 500M ETC., COMPLETE, BUT EXCLUDING ROAD CUTTING (BT/CC) CHARGES., COMPLETE FOR FINISHED ITEM OF WORK - EXCLUDING GST SUPPLYING & FIXING BRONZE HORIZONTAL CHECK (NON RETURN) VALVE AS PER IS-778 I-CLASS HEAVY DUTY - 25 MM NB SIZE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK . SUPPLY AND TRANSPORTATION OF CONTROL PANEL FOR THREE PHASE SUBMERSIBLE MOTORS UP TO 5 HP @ 415V 50HZ OPERATING FITTED WITH SUPPLY AND FIXING OF DIRECT - ON - LINE LTLK (L&T) /BCH/ SIEMENS / CROMPTON MAKE, 0-500V VOLT METER AND 0-30A AMMETER, INDICATION LAMPS, SELECTOR SWITCHES, CTS, 32A TP MCB, SINGLE PHASE PREVENTOR,SUITABLE CONTACTOR TO WITH STAND LOW VOLTAGE PICK UP AND HIGH VOLTAGE RESISTANT, WITH ISI MARKED CAPACITORS ASSEMBLED WITH ISI MARK CONTACTORS AND FITTED WITH LEGRAND MAKE ISI MARK MCB ETC., COMPLETE FOR FINISHED ITEM OF WORK - EXCLUDING GST SUPPLY OF CLAMPS AND BORE COVER BUT EXCLUDING GST INSTALLATION CHARGES FOR LOWERING PUMPSET INTO THE BOREWELL ALONG WITH CABLE, BUT EXCLUDING GST EARTH WORK EXCAVATION FOR FOUNDATIONS AND DEPOSITING ON BANK, FOR ALL LIFTS AND WITH AN INITIAL LEAD OF 10M INCLUDING ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES SUCH AS SHORING, SHEETING, PLANKING, STRUTTING, DEWATERING SITE CLEARANCE, CLEARING SHURBS, BRUSHWOOD, UNDER GROWTH AND SMALL TREES NOT EXCEEDING 300 MM GIRTH, MEASURED AT ONE METRE ABOVE GROUND ETC., COMPLETE FOR FINISHED ITEM OF WORK INCLUDING DEWATERING CHARGES ETC AS PER SS - 20 B FOR STIFF BLOCK COTTON SOIL , HARD RED EARTH, MURRAM, ORDINARY GRAVEL - MANUAL MEANS UP TO 3M DEPTH - FOUNDATIONS FOR SUMP & DRAIN (APSS 308). CEMENT CONCRETE (1:4:8) PROP. USING 40MM HARD GRANITE MACHINE CRUSHED METAL WITH MACHINE MIXING UP TO PLINTH LEVEL INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LAYING, CURING, FINISHING, ALL OTHER INCIDENTAL, OPERATIONAL, LABOUR ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK SUMP & DRAIN FOUNDATION BED (APSS NO: 402). ORNAMENTAL PLASTERING 12MM THICK WITH A BASE COAT OF 8 MM THICK IN CM (1:5) PROP. AND FINISH COAT OF 4MM THICK IN CM (1:3) PROP. WITH DUBARA SPONGE FINISHING COMPLETE INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES, SCAFFOLDING, LIFTING (MANNUAL), CURING, ALL OTHER INCIDENTAL AND OPERATIONAL CHARGES ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS COMPLETE FOR FINISHED ITEM OF WORK FOR SUMP (APSS NO: 901 & 904) RE-FILLING WITH USEFUL AVAILABLE EXCAVATED EARTH OTHER THAN EXPANSIVE SOILS LIKE RED EARTH AND ORDINARY GRAVEL ETC., (EXCLUDING ROCK) IN TRENCHES, SIDES OF FOUNDATIONS AND BASEMENT WITH INITIAL LEAD IN LAYERS NOT EXCEEDING 15 CM THICK, CONSOLIDATING EACH DEPOSITED LAYER BY WATERING AND RAMMING INCLUDING COST AND CONVEYANCE OF WATER TO WORK SITE AND ALL INCIDENTAL, OPERATIONAL, LABOUR CHARGES , HIRE CHARGES OF T & P ETC., COMPLETE FOR FINISHED ITEM OF WORK. SUMP & DRAIN (APSS NO. 309 & 310) PROVIDING IMPERVIOUS COAT TO EXPOSED RCC ROOF SLAB SURFACE IN CM(1:3), 20MM THICK WITH 1KG OF WATER PROOF COMPOUND PER BAG OF CEMENT LAID OVER ROOF WHEN IT IS GREEN, INCLUDING COST OF ALL MATERIALS, COST & CONVEYANCE OF ALL MATERIALS, INCIDENTAL, OERATIONAL AND LABOUR CHARGES LIFTING (MANUAL) FOR MIXING MORTAR, LAYING, RENDERING SMOOTH AND THREAD LINING, , CURING, ROUNDING OFF JUNCTIONS OF WALL AND SLAB ETC,, BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK. FOR SUMP & DRAIN (APSS.NO: 901&903) PROVIDING HYSD/TMT STEEL BARS OF DIFFERENT DIAMETERS BELOW 36MM DIAMETER FE 500 GRADE (AS PER IS 1786 - 2008 AND ALL ITS LATEST AMMENDMENTS) FROM CATEGORY - B STEEL MANUFACTURES WIH MINIMUM INSTALLED PRODUCTION CAPACITY OF 2 LAKH MT PER ANNUM TO 10 LKAHS MT PER ANNUM LIKE GOEL, SHYAM, JAI BALAJI, AF STAR / MS LIFE TMT, RADHA TMT, SUGUNA MT, SHREE TMT) FOR REINFORCEMENT INCLUDING CUTTING, BENDING TO REQUIRED SIZES AND SHAPES, PLACING THEM IN POSITION WITH COVER BLOCKS OF APPROVED SHAPE AND SIZE, TYING FIRMLY WITH M.S BINDING WIRE OF SWG, FORMING GRILLS FOR REINFORCEMENT WORKS AS PER APPROVED DESIGNS AND DRAWINGS TO BE SUPPLIED AT THE TIME OF EXECUTION OF WORK INCLUDING COST AND CONVEYANCE OF DEFORMED BARS, BINDING WIRE, COVER BLOCKS AND ALL WASTAGES SUCH AS OVER LAPS, COUPLINGS, WELDED JOINTS, CHAIRS, SPACE BARS ETC., AS DIRECTED BY THE ENGINEER-IN-CHARGE AND ALL OPERATIONAL, INCIDENTAL LABOUR CHARGES SUCH AS CUTTING, BENDING, PLACING IN POSITION, TYING, EXCLUDING GST ETC., COMPLETE FOR FINISHED ITEM OF WORK FOR ALL LENGTHS AS PER DRAWINGS AND TECHNICAL SPECIFICATIONS FOR BARS BELOW 36MM DIA WHERE THEY ARE NOT WELDED. SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING CENTERING USING STEEL SCAFFOLDING PIPES, JACK PROPS, STEEL CENTERING PLATES, ETC., UPTO UNSUPPORTED HEIGHT 3.66 M ,CURING , (LIFTING MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR SUMP SIDE WALLS OF 230MM THICK (APSS NO.403) SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING CENTERING USING STEEL SCAFFOLDING PIPES, JACK PROPS, STEEL CENTERING PLATES, ETC., UPTO UNSUPPORTED HEIGHT 3.66 M , VIBRATING, CURING , (LIFTING MANUAL) ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK. FOR SUMP TOP SLABS 125MM THICK (APSS NO.403) SUPPLY AND PLACING OF THE DESIGN MIX CONCRETE OF M25 CORRESPONDING TO IS 456 USING WEIGH BATCHER WITH 20MM SIZE GRADED MACHINE CRUSHED HARD GRANITE METAL (COARSE AGGREGATE) FROM APPROVED QUARRY INCLUDING COST AND CONVEYANCE OF ALL MATERIALS LIKE CEMENT, FINE AGGREGATE (SAND - 0.40 CUM) COARSE AGGREGATE (0.80 CUM), WATER ETC., TO SITE INCLUDING ALL OPERATIONAL, INCIDENTAL AND LABOUR CHARGES SUCH AS WEIGH BATCHING, MACHINE MIXING, LAYING CONCRETE, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS. COMPLETE WITH MINIMUM CEMENT CONTENT OF 380 KGS PER CUM OF CONCRETE, INCLUDING CENTERING, CURING , ETC COMPLETE BUT EXCLUDING COST OF STEEL AND ITS FABRICATION CHARGES FOR FINISHED ITEM OF WORK FOR SUMP BOTTOM SLAB (APSS NO.403) SUPPLY, TRANSPORTATION AND INSTALLATION OF 5.00 HP THREE PHASE OPEN WELL ISI SUBMERSIBLE MOTOR PUMPSET, EXCLUDING GSTMAKES: TEXMO / CRI / KSB / ARYENVARSHA / LUBI / FALCON CONSTRUCTING 914.0 MM ( 3-0) DIA BRICK MASONARY MAN HOLE AS PER IS-4111:PART-1:1986 WITH CM (1:6) PROP. USING 2ND CLASS BRICKS OF 225MM THICK FROM APPROVED SOURCE HAVING A MINIMUM CRUSHING STRENGTH OF 5N/SQ.MM INCLUDING PLASTERING WIH CM(1:3) PROP. 12 MM THICK BOTH INSIDE AND OUTSIDE, FITTED WITH 20 DIA RCC COVERS AND FRAMES, INCLUDING EXCAVATING PITS UP TO A DEPTH OF 914.4 MM (3-0) IN ALL SORTS OF SOILS (EXCLUDING ROCK) AND LAYING CEMENT CONCRETE (1:4:8) 150 MM THICK USING 40 MM HBG METAL AND PCC (1:2:4) BENCHING AND CHANNEL 100 MM THICK AS PER STANDARD SPECIFICATION AND INCLUDING COST AND CONVEYANCE OF ALL MATERIALS TO SITE, COST OF ALL INCIDENTAL AND OPERATIONAL, LABOUR CHARGES LIKE MIXING CEMENT MORTAR, CONSTRUCTING MASONRY, CURING ETC., BUT EXCLUDING SEIGNIORAGE CHARGES & GST ON ALL MATERIALS, COMPLETE FOR FINISHED ITEM OF WORK AS PER STANDARD SPECIFICATION. SUPPLYING, LAYING, JOINTING AND TESTING OF 152.40 MM DIA SWG SP-1 PIPES OF ISI MAKE CONFIRMING TO ISI:651&4127, WITH AIRTIGHT CEMENT JOINTS IN CM(1.5:1) PROP. INCLUDING EXCAVATION OF TRENCHES AND SOCKET PITS IN ANY SOIL (EXCEPT ROCK REQUIRING BLASTING) UP TO 1.52M (5-0) DEPTH AND REFILLING WITH EXCAVATED SOILS, WATERING, TAMPING, COST AND CONVEYANCE OF ALL MATERIALS TO SITE, LABOUR CHARGES ETC., BUT EXCLUDING GST , COMPLETE FOR FINISHED ITEM OF WORK. Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in wall with all required accessories [like U nails, Junction box, PVC Bends and Cement] including masonary work for light, fan, common, separate plug point and switch/power boards etc., including all labour charges etc., complete but excluding GST. Makes: Sudhakar / Modi / VIP/Precission. Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe on surface on wall with all accessories fixing on chromium plated metallic base saddles including all labour charges etc., complete but excluding GST. Makes: Sudhakar / Modi / VIP/Precission. Supply and fixing of ISI 25mm outer dia heavy grade with IS:9537 part 3 rigid PVC pipe concealed in underneeth the floor with all required accessories including masonary work and labour charges etc., complete but excluding GST. Makes: Sudhakar / Modi / VIP/Precision. Supply and fixing of 25mm SWR reinforced flexible conduit pipe including all labour charges etc., complete but excluding GST. Make: Precision or its equivalet. Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non-Residential Buildings but excluding GST. Copper cable Make:Sudhakar (HFFR) /Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry. Wiring with 3 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for Ceiling and exhaust fan points in Non-Residential Buildings but excluding GST. Copper cable Make:Sudhakar (HFFR) /Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/ Gold Medal Curve. Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.. Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, without 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non-Residential Buildings but excluding GST. Copper cable Make:Sudhakar (HFFR) /Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Wiring with 3 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, without 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for Ceiling and exhaust fan points in Non-Residential Buildings but excluding GST. Copper cable Make:Sudhakar (HFFR) /Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/ Gold Medal Curve. Wiring with 2 runs of 1.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694/2010, IS 17048 specification for Copper cable in existing pipe with 6A / 10A 1 Way 1 Module Modular Switch control with suitable Module Hot Dip Galvanized modular type Metal Box covered with suitable Modular Cover Frame, with 3 Plate Jumbo Ceiling Rose including all labour charges etc., complete for light and bell points in Non-Residential Buildings for stair case points but excluding GST. Copper cable Make:Sudhakar (HFFR) /Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Ceiling Rose Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry.. Supply and fixing of 6 / 10A 3/2 Pin 2 Module Modular Socket with shutter. with 6 / 10A 1 Way 1 Module Modular Switch control on a Common switch board with suitable Module Hot Dip Galvanized Modular Metal Box covered with suitable Modular Cover Frame with earth continuity including wire leads, earth connections along with all labour charges etc., complete but excluding GST. Modular Switch, Socket, Metal box & Cover frame Make: Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Supply and fixing of 20A 2 Module Modular Socket with shutter and 16A / 20A 1 Way 1 Module Modular Switch duly recessed in wall with 3 Module Hot Dip Galvanized Modular Metal Box size covered with 3 Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [Power plug] Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Supply and fixing of 10A 3/2 Pin 2 Module Modular Socket with shutter-2 Nos and 6A / 10A 1 Way 1 Module Modular Switch control-2Nos duly recessed in wall with suitable Module Hot Dip Galvanized Modular Metal Box size covered with suitable Modular Cover Frame including earth connections and all labour charges etc., complete but excluding GST. [2 Socket board - for Raw power] Modular Switch, Socket, Metal box & Cover frame Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Supply and fixing Distribution board with 20A SP Plug and Socket with SS enclosure with 10/16/20A 10KA SP MCB, C/D Curve ISI Mark including internal connection and labour charges for surface / flush mounting etc., complete but excluding GST.20A, SP Plug Make: Havells / HPL/Indo Asian (Gold Plus), MCB Make: ABB / Havells/C&S. Supply and run of 3 of 2.5 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel(HFFR), Polycab(HFFR). Supply and run of 3 of 4.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 2 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Supply and run of 5 of 6.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 4 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make:Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR). Supply and run of 5 of 10.0 Sqmm HFFR PVC insulated 1100V grade as per IS:694 / 2010, IS 17048 specification for Copper cable in existing pipe for 4 runs of mains & 1 run of earth continuity inlcuding all labour charges etc., complete but excluding GST. Make: Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel, Polycab. Supply and fixing of batten holder / slanting holder in lieu of ceiling rose of light point complete with all connections and all labour charges without bulb (for new installation) but excluding GST. BH Make: Gold Medal Olive / Million Zoom / Anchor Penta Cherry. Supply and transportation of 20W +/- 10%, >/ 2000 lumens, 1200mm length LED retro tube light, housing made with alluminium anodised body, wide operating voltage with double side connection, PF≥0.9, Surge protection: > 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 6500K as desired by the department and as per IS specifications, minimum CRI≥80 etc., complete with 5 years warranty with BIS Certification.but excluding GST. LUMINAIRE MAKE: Crompton /Havells / OSRAM/Wipro. LED Make: : CREE / NICHIA / OSRAM. Fixing of 20W LED tube light luminaire on wall / Ceiling with all accessories including giving connections and all labour charges etc., complete but excluding GST. Supply and transportation of 18 W +/-10% (>= 1800 Lumens) back lit LED Down Light Recessed / Surface mounting round / square with housing made of Powder coated Pressure die cast aluminium housing with extended heat sink, with Protruded high efficiency diffuser, IP20, with wide operating voltage range, Power factor > 0.9, Surge protection: > 2KV, System efficacy of >100 lumens/watt, CCT: 3000K - 6500K as desired by the department and as per IS, CRI >80, and THD is less than 15% etc., complete with 5 years warranty with BIS Certification but excluding GST. LUMINAIRE MAKE : Crompton /Havells / OSRAM/Wipro LED MAKE : CREE / NICHIA / OSRAM. Fixing of LED luminaire 18W Down lights with all necessary accessories in false ceiling / on wall including giving connections and all labour charges etc., complete but excluding GST. Supply and Transportation of 36 W +/-10% (>=3600 Lumens)Back lit, 2 x2 grid false ceiling / zip board (595 mm x 595 mm) Recessed / Surface mounted LED luminaire made of CRCA sheet housing with powder coated with high efficiency acrylic wide diffuser, with wide operating voltage range, Power factor > 0.9, Surge protection >2KV, System efficacy of >100 lumens/watt, CCT: 3000K - 6500K as desired by the department, CRI >80, and THD is less than 15% etc., complete with 5 years warranty with BIS Certificationbut excluding GST. LUMINAIRE MAKE: Crompton /Havells / OSRAM/Wipro.LED MAKE : CREE /NICHIA / OSRAM. Fixing of 36W LED luminaire in false ceiling / pop with necessary arrangment including giving connections and all labour charges etc., complete but excluding GST. Supply, Transportation of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 W, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) motor, class of insulation: B, 3 nos blades, 30 cm long down rod, 2 nos canopies, shacklekit, copper winding, Power Factor greater than 0.90, Service Value (CMMAV) greater than 8.0, Air delivery minimum 235 CMM, 350 RPM (tolerance as per IS:374-2019), THD less than 10%. with remote or compatible to electronic step type regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75°C(max), insulation resistance more than 2 mega ohm, suitable for 230V, 50 HZ, single phase AC supply, earthing etc., including all standard accessories etc., complete but excluding GST. Makes: Cromton / Havells / Orient. Supply of 2 Module Modular type Electronic Fan Regulator with 2 Module Hot Dip Galvanized Modular Metal Box covered with 2 modular cover frame etc., complete but excluding GST. Make: Legrand Lyncus / GM Four Five / Anchor Roma Plus/Gold Medal Curve. Labour charges for fixing of Ceiling fan and regulator including transportation and giving connections with twin core wire etc., complete but excluding GST. Supply and erecting 19/20mm steel tube down rod of length with bolts & nuts duly painted with matching colour of fan etc., complete but excluding GST. Supply of 9 (225mm +/ - 5%) Light duty exhaust fan with metal blades etc., complete but excluding GST.Makes: Crompton / Havells Ventilair-DB / Orient hill air. Supply of 18 (450mm) 900 RPM Heavy duty exhaust fan with metallic blades.but excluding GST.Makes: Crompton / Almonard / Havells TurboForce SP. Labour charges for fixing of Exhaust fan in wall with necessary connections etc., complete but excluding GST. (for hole already made available) Supply of 16 (400mm) BLDC 30 W Wall mounted Fan with service value 2.7 CMM / Watt with all accessories etc.,but excluding GST.Makes : Atomberg / Crompton / Orient / Havells / Halonix . Supply and fixing of Cat 6 RJ-45 information outlets including single face plate on 2 moduler hot dip galvanized metal box including giving connections, cost of all accessories and labour charges etc., complete but excluding GST. I/O & duel face plate Makes: D Link / AMP / Molex / Legrand / Krone. Metal box make: Legrand Havells /GM /Anchor. Supply and run of LAN Cable cat - 6 UTP cable in existing PVC conduit including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Makes: D Link / AMP / Molex / Legrand / Krone. Supply and fixing of Modular socket type Telephone jack with Connector on 2 moduler hot dip galvanized metal box and 2 modular cover frame including giving connections, cost of all accessories and labour charges etc., complete but excluding GST. Telephone jack with Connector, cover frame & metal box Makes: Legrand Lyncus / Havells Fabio/GM Four Five/Anchor Roma Plus. Supply and run of 2 Pair, 0.5mm telephone copper wire in existing PVC conduit including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Makes: Finolex / Delton / Surabi / Polycab Supply and fixing of Modular co-Axial socket type TV Antenna outlet on 2 moduler hot dip galvanized metal box and 2 modular cover frame including giving connections, cost of all accessories and labour charges etc., complete but excluding GST. Co-Axial socket type TV Antenna outlet, cover frame &metal box makes: Legrand Lyncus / GM Four Five / Million / Goldmedal Curve / Anchor Roma Plus Supply and fixing of 4 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 12 Nos S.P. outgoings and for 1 No 4 pole Incomer (FP Isolator / MCB) with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc., complete with inter connections but excluding GST.Incommer: 40A FP Isolator - 1No. Outgoing: 6-32A SP MCB, 10kA ISI mark - 12 Nos.DB Makes: ABB / C&S /LK (L&T) Isolator Make: ABB / Havells/C&SMCB Make: ABB / Havells/C&S. Supply and fixing of 8 Way TPN DB Horizontal with IP 43 Protection as per IS:13032 and suitable for 24 Nos S.P. outgoings and for 1 No 4 pole Incomer (FP Isolator / MCB) with 100 A tinned copper busbar, neutral bar, earth bar and cable ties for cable management, fully shrouded neutral bar, profile blanking modules for unused MCB ways, din bars and detachable gland plate etc., complete with inter connections but excluding GST.Incommer: 63A FP Isolator - 1No. Outgoing: 6-32A SP MCB, 10kA ISI mark - 24 Nos.DB Makes: ABB / C&S /LK (L&T) Isolator Make: ABB / Havells/C&SMCB Make: ABB / Havells/C&S.. Supply and fixing of 8 Way VTPN DB with IP 43 Protection as per IS:13032 and suitable for accommodating 63A 10kA TP C/D Curve MCBs - 8 Nos as out goings and 125A 4 pole MCCB as Incommerincluding internal connection and labour charges for surface / flush mounting etc., complete. Incommer: 125A, 4P, MCCB - 1No. Outgoing: 63A, 10KA, TP MCBs - 8 NosDB Makes Legrand / Schneider / Siemens / LK(L&T)MCCB Make:LK (L&T) - D sine / Schneider-NSNSX/Legrand -DP X3/ Siemens-3V /C&S -WinbreakMCB Make:ABB / Havells/C&S. Supply of 4 Core 10.00 Sqmm XLPE insulated, 1100Vgrade armoured alluminium cable with ISI markas per specification confirming to IS:7098 (Part- I) but excluding GST. Makes: Universal / Torrent / Polycab / Gloster. Earth work excavation of Trench in hard ground soil, laying of U.G cables upto 50 Sqmm on sand cushion covering the cable with bricks and back filling of Trench duly providing route indicator embedded in C.C including cost and conveyance of materials and labour charges etc., complete but excluding GST. Labour charges for run of U.G cable on wall / existing pipe with necessary fixing arrangments such as saddles, clamps,wooden separators etc., (as directed by departmental official) etc., complete but excluding GST. Providing independent earthing for Important equipment with 40mm dia B class 2.5m long G.I pipe and 19mm dia B class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II,) but excluding GST. Supply and Run of No.8 SWG G.I wire including cost of all accessories and labour charges etc., complete, but excluding GST. Supply, Installation, Testing and Commissioning of IP Based digtal Telephone (EPABX) system complied with following specifications:> IP @ Core, PCM/TDM, Non blocking,> Must Support PRI, E1, Analog Junctions> Must Support PC Console,> Must support Mobile SIP (Android and I O.S)> Must support Voice Mail> Must support Card based GSM> Inbuilt Call Details Software with searchengine software> 4 Analog Trunks> 6 Digital Extensions> 64 Analog Extensions> 1 Digital Key Phone with minimum 16 Keys(Must work only on 2 wires)> Expandable to 64 Analog Extensions or moreApproved Brands: NEC/ Alcatel/ Karel/Unify Supply, Installation, Testing and Commissioning of Digital Key Telephone with 2 line display, 16programmable keys, fully handsfree talk back. etc., compleate but Excluding GST. Supply and Transportation of of INVERTER Model Cool type split AC unit 2.0 TR 5 Star capable of delivering 21600 BTU/hr and above with operating on refrigerant R-32 / R-410with high wall mounted Single Split 100% copper indoor and outdoor condencing unit Hermetically sealed compressor suitable for operation on 230V, 50Hz, 1Phase AC supply capable ofperforming Heat cool dehumidifying air circulating and filtering with cooling and condensing units with 3.0 mts of copper piping, insulation kit and 4 mts of 4 core copper flexible chord (Voltage range 160- 264 volts) and cordless remote control with with warranty of compressor for 5 years iand comprehensive maintenance for 2 years etc., complete as directed by the Engineer-in-charge but excluding GST. Make: Daikin / Toshiba / Blue Star / Hitachi. Supply and Transportation of 2.5 TR capable of delivering 30000 BTU/hr and above with operating on refrigerant R-32 / R-410 Inverter Cassette type AC unit with ceiling mounted indoor unit and outdoor condencing unit Hermetically sealed compressor suitable for operation on AC supply capable of performing cooling dehumidifying air circulating and filtering with cooling and condensing units etc complete with Wireless remote controller, but without refrigerent piping and cable.with 2 years warranty and annual maintenance contract. but excluding GST. Make: Daikin / Toshiba / Blue Star / Hitachi. Providing 2 runs of Copper tubes for suction and liquid between indoor and outdoor unit for split/Casseete Air-Conditioner including foaming etc., complete but excluding GST.1. 3/4 x 3/82. 5/8 x 1/43. 1/2 x 1/4 or equivalent sizes. Installation of INVERTER Model Cool type split Air Conditioners (Indoor and Outdoor units) including all accessories etc., complete as directed by the Engineer-in-charge but excluding GST. Installation of Installation of Cassette type Split Air Conditioners. (Indoor and Outdoor units) including all accessories etc., complete as directed by the Engineer-in-charge but excluding GST. Supply, Fabrication of 1set MS bracket suitable for fixing out door unit of Split AC unit including all accessories etc., complete but excluding GST. Supply, Fabrication of 1set MS bracket suitable for fixing out door unit of Casette AC unit including all accessories etc., complete but excluding GST. Supply of 4 core 2.5 Sqmm PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc., complete but excluding GST.Make: RR kabel / Havells / Polycab/KEI/Nakoda/Sudhakar. Supply, Transportation, Installation, Testing and Commissioning of 10KVA on line double conversion UPS with External Battery system, SNMP controls, LCD display, Pure sine wave output, USB Compatible, Harmonic distortion less than 3%, Built in maintenance bypass, Output overload operation : 10 minutes at 125% and 60 seconds at 150%, Maximum short-circuit current 10kA, Crest factor 3:1, IP20 degree of protection, Dust filter and conformance coated boards for harsh environment with auto static switch three phase input / Three phase output and modular structure for better thermal technology / cooling facility, including 65AH-12V External SMF Batteries - 16 Nos, suitable Rack for mounting external batteries, suitable copper links with warranty upto two years with CE, EAC, RCM certifications etc., complete but excluding GST. UPS Makes: APC / Numeric / Emerson. Battery Makes: Exide / Amaron Quanta. UPS Model No. E3SUPS10KH or its equivalent. Supply of 10.0 Sqmm 4 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc., complete but excluding GST. Makes: Finolex / RR kabel / Havells / Polycab. (From Panel board to UPS) Labour charges for run of above XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor on wall / existing pipe with necessary fixing arrangements such as saddles, clamps, wooden separators etc., (as directed by departmental official) etc., complete but excluding GST. Supply and fixing of 12 Way SPN DB with IP 43 Protection as per IS:13032 and suitable for 40A DP MCBs - 4 Nos as outgoings and for 63A FP Isolator - 1No as Incommer including internal connection and labour charges for flush mounting etc., complete but excluding GST.Incommer: 63A FP Isolator - 1No. Outgoing: 40A, 10KA, C/D Curve DP MCBs - 4 Nos.DB Make: ABB / C&S /LK (L&T) Isolator Make: ABB / Havells/C&SMCB Make: ABB / Havells/C&S. Supply, Installation, testing and commissioning of EN54-2 Listed and UL approved based analog addressable 4 loop micro processor fire control panel expandable by minimum 2 additional loops with minimum 640 character LCD display. Each loop of panel shall have maximum capacity 250 analogue addressable devices, and shall have 20% of spare capacity, 240 volts A C Power supply, automatic battery charger, 24V SLA batteries suitablefor operating the entire system including talk back units and the hooters/strobes for a minimum of 4 hours in battery condition the panel shall have suitable power amplifiers for hooter / strobes the panelshall be capable beeing integrated with the BMS system and shall include cost of supply, installation of any additional modules or interfaces required for the same.But excluding GST.Make: Notifier / Edwards / Honeywell / Morley IAS Supply and fixing of addressable wall mounting strobes cum hooters including the cost of mounting accessories complete as per specifications and as required including testing and commissioning. But excluding GST. Make: Notifier / Edwards / Honeywell / Morley IAS / Bosch / Honeywell / Morley IAS Supply and installation of addressable analogue manual call point with resetable flexible element to initiate alaram including the cost of mounting accessories etc. complete. But excluding GST. Make: Notifier / Edwards / Honeywell / Morley IAS Supply and instllation of intallegent analogue addressable photo electric smoke detector including cost of base plate etc., complete as per specification with required fittings and accessories. But excluding GST. Make: Notifier / Edwards / Honeywell / Morley IAS (Above False Ceiling) Supply and instllation of intallegent analogue addressable photo electric smoke detector including cost of base plate etc., complete as per specification with required fittings and accessories. But excluding GST. Make: Notifier / Edwards / Honeywell / Morley IAS (below False Ceiling) Supply and installation of UL approved intellegent analogue addressable rate of rise cum fixed temparature heat detectors including the cost of base plate. 75mm dia MS outlet box for fixing of the detector base, mounting accessories etc., complete as per specifications and as required. But excluding GST.Make: Notifier / Edwards / Honeywell / Morley IAS Supply and Installation of UL approved intellegent analogue addressable fault isolator modules including the cost of mounting accessories complete as per specifications and complete as required. But excluding GST. Make: Notifier / Edwards / Honeywell / Morley IAS Supply and installation of response indicators for above false ceiling detectors. But excluding GST.Make: System Censor / Ravel / Vertex /Seaara Supply of 1.5 Sqmm, 2 core PVC / XLPE Insulated, Flexible Armouring Flexible Copper cable as per IS 7098 / Part-I / 1988 including all transportation charges etc complete.But excluding GST. Make: RR kabel / Havells / Polycab /RPG / KEI Supply and fixing of ABC Powder type fire extinguisher of 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure gas cartridge, discharge hose, wall mounting bracket / stand etc. complete, confirming to IS:15683 But excluding GST.Make: FIREX /MINIMAX/ ARMOUR/SAFEX/CEASEFIRE Supply and fixing of Co2 4.5 Kg capacity type extinguisher with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure, discharge hose, wall mounting bracket / stand etc. complete, confirming to IS:15683. But excluding GST. Make: FIREX /MINIMAX/ ARMOUR/SAFEX/CEASEFIRE Supply and transportation of 120 W +/-10% (>12000 Lumens) LED HIgh Bay Luminaire with high power COB LED made of pressure diecast alluminium housing with powder coated,Supply Input voltage 120 -270 V AC, P.F > 0.90, high power LEDs, System efficacy >100 lm / W and junction temprature < 70°C, with Ingrees protection IP65, IK05, Driver surge protection 4KV, external Surge protection ≥ 5KV with wide/ Narrow beam optics, THD<10% at 110 Volts AC, driver efficiency >90%, CCT: 3000K - 5700K, minimum CRI>70, etc., complete with BIS certification with warranty 5 years warranty. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates. But excluding GST. LUMINAIRE MAKE: CROMPTON/ OSRAM / Wipro/ HavellsLED Make: CREE/NICHIA/OSRAM Supply and Transportation Central Control Unit Stsyem with recording Controller for Conference Model CCSD-CURD. But excluding GST. Make: Bosch Supply and Transportation of Chairman Unit with Chairmen Priority. But excluding GST. Model CCSD-DL(CM) . Make: Bosch Supply, Transportation of Conference Delegent Units. Model CCSD-DL. But excluding GST. Make: Bosch Supply, Transportation of 30w premium Loud Speakers. But excluding GST. Model: LB2-UC30 . Make: Bosch Supply, Transportation of 120W Mixing Amplifier. But excluding GST. Model :-PLE-1ME-240-3IN . Make: Bosch Supply of Handheld ULM Wireless Microphone. But excluding GST. Make: EV. model No:-R300-HD Supply and fixing of 5000 Lumens WXGA Laser Light Source Projector. But excluding GST. Make: Sony. Model No:- VPL-CWZ10 Supply and installation of UV 430 Series 4K Conference PTZ Camera, 4K @60Fps, 1/2.5 Sony CMOS Sensor. Model :- UV430E2 . But excluding GST. Make:MINRAY Supply and Fixing of 10 Channel Audio Mixer . But excluding GST. Make: reputed Supply and transporatation of 137 Motorized Screen. But excluding GST. Make: Liberty/reputed Installation,Testing and Commissioning and Programming charegs for entiore system. But excluding GST. Supplay and transportation of Projector mounting kit. But excluding GST. Supplay and run of 15m HDMI cable. But excluding GST. Supplay and run of 10m HDMI cable model no:- LBB4116/10. But excluding GST. Make: Bosch Supply and installation of 18 U Rack including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Make: Netgear/D-link supply and run of 2 core 1Sq.mm Loud Speaker cable But excluding GST. make: Finolex Supply,Installation,Testing & Commissioining of IP IR Dome Camera (4 MP Series), 4MP Network IR Dome Camera Max. 4megapixel (1920 x 1080) resolution,0.095Lux (Color), 0Lux (B/W, IR LED on), 2.8 ~ 12mm (3.1x) varifocal lens,Max. 30fps@2M all resolutions (H.265/H.264)H.265, H.264, MJPEG codec supported, Multiple streaming,Motion detection, Tampering, Defocus detection,Hallway view (90˚/270˚), LDC support,Micro SD/SDHC/SDXC memory slot (Max. 128GB),IR viewable length 20m,PoE/12VDC UL Certified Dome Camera. But excluding GST.Make: Sumsung Model:QND-6072D or its equivalent Specification of Makes CPPLUS/ Honeywell / Sony /Panasonic. Supply,Installation,Testing & Commissioining of IP IR Bullet Camera (4 MP Series), 4MP Network IR Dome Camera Max. 4megapixel (1920 x 1080) resolution,0.095Lux (Color), 0Lux (B/W, IR LED on), 2.8 ~ 12mm (3.1x) varifocal lens,Max. 30fps@2M all resolutions (H.265/H.264)H.265, H.264, MJPEG codec supported, Multiple streaming,Motion detection, Tampering, Defocus detection,Hallway view (90˚/270˚), LDC support,Micro SD/SDHC/SDXC memory slot (Max. 128GB),IR viewable length 20m,PoE/12VDC UL Certified Dome Camera. But excluding GST. Make: Sumsung Model:QND-6072D or its equivalent Specification of Makes CPPLUS/ Honeywell / Sony /Panasonic. Supply,Installation,Testing & Commissioining of IP65 IR PTZ Camera- 12M 32x Network PTZ Dome Camera Max. 2megapixel (1920 x 1080) resolution,4.44 ~ 142.6mm (Optical 32x) lens,Max. IR viewable length : 200m (656ft),Day & Night (ICR), WDR (150dB), DIS (Built-in gyro sensor),Intelligent Video / Audio Analytics, Shock detection,Azimuth display (Cardinal & intermediate directions),Multiple streaming, WiseStream II support H.265, H.264, MJPEG codec support MicroSD / SDHC / SDXC memory 2 slots (Up to 512 GB) IP66, IK10 UL Certifed PTZ Camera along with pole/wallmount bracket. But excluding GST. Make: Samsung Model:XNP6320H orits equivalent Specification of makes Honeywell / Sony /Panasonic. Supply, installation,Testing and Comissioning of 32 channel NVR (Network Video Recorder) Max. 12MP Camera supported,256Mbps network camera recording,Support 4K video out on HDMI monitor,Support Dual monitor video out,Support H.265, H.264, MJPEG compression, Wise Stream support, Max. 8 internal HDDs (48TB), e-SATA / iSCSI storage support, Support RAID 5 Easy installation with front swap hard disks ARB & Failover (N+1) support, UL Cerfified NVR. But excluding GST. Make: Honeywell / Sony /Panasonic. Supply and fixing of Surveillance HDD-10 TB. But excluding GST.Make: Seagate/Hitachi/TOSHIBA Supply and installation of 4K UHD , 55” LED Display complete Make- Samsung QB55R with following Specifications :a) Diagonal Size 55b)Type Edge LED BLU.c) Resolution 3840*2160 (4K UHD) d) Pixel Pitch(mm)0.105 x 0.315.e) Active Display Area(mm)1209.6(H) x 680.4(V)f) Brightness(Typ.) 350 nit.g) Contrast Ratio 4000:1. But excluding GST.Makes: Samsung QB55R or its equivalent make in Dell / LG / Samsung / Lenovo / HP Supply and fixing of 8 PoE 1GB ports + 4 Gigabit SFP ports Web Smart Switch. But excluding GST.Make: D-Link Model No.DGS1210-8P or its Equivalent make in Cisco/Netgear/HP Supply and run of LAN Cable cat - 6 UTP cable in existing PVC conduit including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Makes: D Link / AMP / Molex / Legrand / Krone. Supply and installation of 18 U Rack including cost and conveyance of all materials and labour charges etc., complete but excluding GST. Make: Netgear/D-link Supply, transportation, installation, testing and commissioning of 6 passenger Machine Room less elevator with following specifications with connected minor civil works required for installation of Lift including all accessories, scoffolding, requried channels, loading and unloading of materials etc, including comprehensive maintenance of lifts during the defect liability period.Specifications:a)Type : Machine room lessb)Pit Depth :1600 mm or as per NBCc) Minimum Floor to Floor Height (Required) :As per Standardd)Travel height : 3.9mtrse)Head room Height : 4.0mtrsf)Lintel Height (Required) : 2240mm fromfinished floor level +/- 10%g)Number of persons : 6 Ph)Rated Load : 408 Kgsi)Number of Stops : 2j)Number of Access sides : 1k)Floor Designations : G+1l)Drive Sytem : Alternating current, VoltageFrequency Drive (ACVF).m)Type of Controller : Fully collective control -Simplex .n)Speed of Travel : .1 m/so)Car size : 1100mm wideX1000MM deepX2200mm highp)Door width : 800mm q)Door Height : 2000 mm r)Rated output motor : as per standards)Car Design : Car walls finish in Stainless stell hairline finish LED spot in ceiling.t)Car Doors : stainless steel hairline finish.Granite Flooring finish in Black sea.Deco ceiling finish in stainless steel Hairline.Full Height mirror on rear car panel.u)Car Operating Panel : full hoeght stainless steel Mechanical pushbutton.Door open/close and alarm buttons /Touch panel or equivalent, Visual callconfirmation, Car position Indicator,announcing arrows for collective controls,Segment displayautomatic landing doors with stainless steelhairline finish.Center Opening or Side Opening as per the site conditionv)Special Features :Closed loop control systemSelf Diagnostic controlOverload detectionAutomatic evacuation to nearest floor(ARD)Light curtain on car entranceAlarm HornFire SwitchHandrail in stainless steel finish on rear wallAuto Fan offAuto light offIntercom-3way Supply, transportation, installation, testing and commissioning of 2 Ton Goods Machine Room less elevator with following specifications with connected minor civil works required for installation of Lift including all accessories, scoffolding, requried channels, loading and unloading of materials etc, including comprehensive maintenance of lifts during the defect liability period.Makes: Schindler / Kone / OTIS /JohnsonSpecifications:a)Type : Machine room lessb)Pit Depth :1800 mm or as per NBCc) Minimum Floor to Floor Height (Required) :As per Standardd)Travel height : 3.9mtrse)Head room Height : 4.2mtrsf)Lintel Height (Required) : 2240mm fromfinished floor level +/- 10%g)elevator type : Goods elevatorh)Rated Load : 2000 Kgsi)Number of Stops : 2j)Number of Access sides : 1k)Floor Designations : G+1l)Drive Sytem : Alternating current, VoltageFrequency Drive (ACVF).m)Type of Controller : Fully collective control -Simplex .n)Speed of Travel : .1 m/so)Car size : 1600mm wideX2600MM deepX2200mm highp)Door width : 1200mm q)Door Height : 2000 mm r)Rated output motor : as per standards)Car Design : Car walls finish in Stainless stell hairline finish LED spot in ceiling.t)Car Doors : stainless steel hairline finish.Granite Flooring finish in Black sea.Deco ceiling finish in stainless steel Hairline.Full Height mirror on rear car panel.u)Car Operating Panel : full height stainless steel Mechanical pushbutton.Door open/close and alarm buttons /Touch panel or equivalent, Visual callconfirmation, Car position Indicator,announcing arrows for collective controls,Segment displayautomatic landing doors with stainless steelhairline finish.Center Opening or Side Opening as per the site conditionv)Special Features :Closed loop control systemSelf Diagnostic controlOverload detectionAutomatic evacuation to nearest floor(ARD)Light curtain on car entranceAlarm HornFire SwitchHandrail in stainless steel finish on rear wallAuto Fan offAuto light offIntercom-3way Fabrication ,Transportation , Supply, Installation, Testing and Commissioning of suitable size , plinth mounting indoor type LT Distribution panel of 14 guage CRCA sheet ,the following incorporated in the panel for Distributing the power supply .Main incoming: 1) 250A FP 35 KA, MCCB (Thermal Magnetic release) -1No. Make: L&T- D sine / Legrand -DP X3/ Siemens-3V. 500A Alluminium Bus bar (60mmx10mmxSuitable length) - 12nos -Main 20x6mm for links - Required length Insulators for busbar fixing (panel type) - 12 Nos Phase indicator LED lamps - 1set SALZER L&T make ,Extended earth terminals - 1 no with 40X6 mm G.I Strip Current Transformer-250/5A - 3 Nos KAPPA make Voltmeter(0-500V) - Digital type with selector switch - 2 No ( conzerv Make) Ammeter (0-250A) - Digital type with selector switch - 2No ( conzerv Make) with Wiring ( Copper cable should be HFFR ISI Mark i.e 2.5 sq mm for control cable and 10sq mm for links) Make :Sudhakar (HFFR) / Nakoda (HFFR), KEI (HFFR), RR kabel (HFFR), Polycab (HFFR).Outgoing :125A Fp 35 KA MCCB -4 No, Make: L&T- D sine / Legrand -DP X3/ Siemens-3V.63A,FP 25 KA, MCCBs -2Nos, Make: L&T- D sine / Legrand -DP X3/ Siemens-3V. 63A,FP , MCBs - 8No, Make: ABB/Havells/C&S (Thermal Magnetic release) The panel Size approx:1.55M X1.50M X0.4M the connections of all MCBs and MCCBs should be done with Bus bar strips with bottom entry cables. the above Panel shall be cleaned with 7 tank process and painting with one coat of red oxide and two coats of powder coated light grey as per IS 631 of (5) etc complete and provided suitable base channel of 75x40x6mm size etc., complete and internal wiring of Bus bar to indicator lamps , Digital ammeter, Digital voltmeter with selector switches with SP MCB Protection as directed by the Engineer- in - Charge. r)Rated output motor : as per standard s)Car Design : Car walls finish in Stainless stell hairline finish LED spot in ceiling. t)Car Doors : stainless steel hairline finish. Granite Flooring finish in Black sea. Deco ceiling finish in stainless steel Hairline. Full Height mirror on rear car panel.u)Car Operating Panel : full hoeght stainless steel Mechanical push button.Door open/close and alarm buttons / Touch panel or equivalent, Visual call confirmation, Car position Indicator, announcing arrows for collective controls, Segment display automatic landing doors with stainless steel hairline finish. Center Opening or Side Opening as per the site conditionv)Special Features : Closed loop control system Self Diagnostic control Overload detection Automatic evacuation to nearest floor(ARD) Light curtain on car entrance Alarm Horn Fire Switch Handrail in stainless steel finish on rear wall Auto Fan off Auto light off Intercom-3way Providing CTPT plinth 600mm x 600mm x 2.1 mtr in size with necessary excavation in ground at the bottom with 150mm thick 1:2:4 cement concrete raft at the bottom and top duly plastered 20mm thick outsides including watering etc., complete.but excluding GST. Providing independent earthing by exacavating a pit to a depth of 2.25Mtr in all soils as per size specified in the data for Sophisticated Electronic equipment with 600mm x 600mm x 3.15mm thick copper plate rigidly fixed to 19mm dia B Class G.I Pipe of 2.5Mtr lengthwith funnel as per National Electric Code and earth connection from electrode GI strip of 40mm x 5mm x 200mm length to be bolted with nut bolts to G.I.pipe including 25mm x 3mm copper strip of 6Mtrs length connected from plate to GI strip including filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe and providing CC / Brick massonry chamber 450mmX450mmX400mm and covered with R.C.C. Slab including all accessories and labour charges etc complete as per IS specification 732/1982 (Part II). but excluding GST. Providing independent earthing for Important equipment with 40mm dia B class 2.5m long G.I pipe and 19mm dia B class G.I pipe of 0.3mtr. long connected with reducer providing G.I funnel with mesh enclosed in C.C/ brick massonry chamber of 450m x 450m x 400mm with R.C.C. Slab cover duly providing staggered holes filling with 20Kg Salt and 40Kg Charcoal or 40Kg bentonite powder from the bottom of the pipe giving earth connection from electrode through G.I strip of 40 x 6mm x 200mm length with all accessories and labour charges complete, as per IS specifications 732/1982 (Part II) but excluding GST. Supply and Run of 32mm x 6mm copper strip including cost of all accessories and labour charges etc., complete.but excluding GST. Supply and Run of 40mm x 6mm G.I Strip including cost of all accessories and labour charges etc., complete.but excluding GST. Supply of round bottom G.I sheet bucket of 9 Ltrs. Capacity as per IS:2546 made out of 24 gauge GI sheet with extra handle at bottom duly painted inside and red out side with printed with FIRE Mark for stand and hook and filled with sand and arranged to existing stand or hook includiing all accessories etc., complete but excluding GST. Providing floor mounting stand for keeping 4No of fire bucket 1500mm length, 900mm height made out of 40x40x6mm angle iron welded with 4 hooks and duly painted with one coat of red lead and two coats of enamel paint includiing all accessories etc., complete but excluding GST. Supply and fixing of ABC Powder type fire extinguisher of 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure gas cartridge, discharge hose, wall mounting bracket / stand etc. complete, confirming to IS:15683 complete but excluding GST. Make:FIREX /SAFEX / CEASEFIRE Supply of First Aid Box 18X12X8 but excluding GST. Providing of Danger Notice Plates of size 250x200mm, shall comply with IS:2551-1982 but excluding GST. Providing of Shock instrution chart in English / Hindi / Telugu duly framed with front glass but excluding GST. Supplying of Pair of rubber hand gloves suitable for working on 11/22KV but excluding GST. DG SET: Supply, Transportation, erection and commissioning (Excluding Foundation) of 3 Phase, Phase, 415, 50Hz, water cooled multi cylinder diesel generator set with alternator of 160 KVA continuous rating directly coupled Engine, Alternator and radiator with guard and mounted on a common base frame of Robust construction and complete with standard control panel having IP-52 protection, anti vibration mounts of reputed make, Acoustic Enclosure as per CPCB norms IV, sound absorbing material to restrict sound level up to 75 dB up to 1 mtr distance and etc as per the following specifications mentioned but excluding GST.A. Alternator : Kirloskar / Stamford / CromptonGreaves / Leroy Somer make. The alternator ofthe output rating shall be 3 Phase, 415V, 50Hz,Ac , 0.8 P.F. lagging at 1500 RPM. Thealternator is self excited, self regulated, andshall confirm to IS: 13364 of 1992 withregulation of +5% from no load to full load.degree of protections shall be IP21.B.Diesel Engine : Kirloskar / Cummins /Mahindra & Mahindra / Greaves Cotton /Eicher / Ashok Leyland Diesel Engine start,developing suitable -------------- BHP output at1500 RPM with mechanical / electronicgoverning so as to enable the alternator to give- - - - -KVA continuous output at 0.8 P.F.lagging at NTP conditions. The diesel engineshall be capable of providing 10% O/L for 1 Hrfor every 11 Hrs of continuous running at fullload. The engine with 1st filling of oil andDiesel etc.with standard control panel.01. Exhaust pipe of required size as per thestandards.02. Diesel tank suitable for 8 to 12 Hoursrunning capacity.03. Residential Silencer.04. SMF Batteries with leads as per theManufacturer standards Supply of 2.5 Sqmm 8 Core PVC/XLPE Insulated, Flexible Armouring Flexible Copper cable as per IS 7098 / Part-I / 1988 including all transportation charges etc complete but excluding GST.Makes : RR kabel / Havells / Polycab/KEI/Nakoda/Sudhakar. Fabrication, Transportation and supply of hot-dip galvanized Octogonal Pole with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate with door opening arrangement, including chain for anti theft mechanism, supply of suitable boards with bakelite sheet, din channel for MCBs as per IS specification suitable to withstand the wind speed of 180 KMPH for 7.50 Mtrs height Pole having dimensions Bottom 130mm, Top 70mm with 3mm thick, base plate 220 x 220 x 12mm and 4 Nos of M20 x 700mm long J bolts along with template or equivalent including all accessories etc., complete but excluding GST. Makes: BAJAJ / TRANSRAIL. Fabrication, Transportation and supply of 1.5 Mtr sword type or any decorative Single arm bracket with dooms made with MS galvanized 50mm dia Pipe etc., complete but excluding GST. Makes: BAJAJ / TRANSRAIL. Foundation and erection charges with special T&P, for 7.50 Mtrs long Octagonal / Conical pole duly erecting on base plate duly provided 4 Nos foundation bolts with nuts with providing of 0.45Mtrx0.45Mtrsx1.20 Mtr size M20 cc work vibrated concreting mixing with necessary steel (10kgs) reinforcement as directed by the field engineers during execution including centering, decentering, water curing as required, soil exacavation, back filling, muffing removal and coil earthing including all labour charges and cost and conveyance of materials etc., complete but excluding GST. Erection charges for 7.50 Mts long Octagonal pole on bridge kerb portion (R.C.C). duly provided 4 Nos 8 Anchor bolts/ M20xsuitable J type bolts etc duly drilling holes to RCC slab and with V.C.C. M.15 concrete for base concreting up to a height of 8 with necessary Reinforcement work etc. including cost and conveyance of all material and all labour charges etc. complete as directed by the department officers. but excluding GST. Supply and fixing of 1 No.10A 10KA, C/D Curve ISI Mark SP MCB in existing M.S. box with Din channel, 4way 63A connector including cost & conveyance of all materials and labour charges etc., complete but excluding GST. Make: ABB / Havells/C&S Supply and transportation of 90W +/-10% (>=9000 Lumens) LED Street light Body made of high grade pressure die – cast Aluminium alloy with corrosion resistant powder coat, having protective toughened glass cover, Suitable lens on LEDs, Less Glare, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66) protected, wide operating voltage range, P.F > 0.90, System having efficacy >110 lumens/watt, with Ingress protection IP66, Potted driver, Driver surge protection >10KV, THD<15%, CCT: 3000 - 6500K as desired by the department and as per IS, CRI>70, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc., complete with BIS certification with 5 years warranty. The contractor has to furnish themanufacturer warranty letter, LM 79 and LM 80 certificates etc., complete but excluding GST.LUMINAIRE MAKE : CROMPTON / HAVELLS / WIPRO /OSRAM. LED MAKE : CREE / NICHIA / OSRAM. Supply and fixing of 2.5 Sqmm 3 Core PVC / XLPE Insulated Sheathed Multi Core Bright Annealed Bare Copper Conductor Heavy Duty Industrial Cables for Voltage Grade upto 1100 Volts as per IS: 694:1990 including all transportation charges etc., complete but excluding GST. Makes : RR kabel / Havells / Polycab / RPG / KEI/Sudhakar Supply of 16 Sqmm 4 Core XLPE insulated, 1100V grade armoured alluminium cable with ISI mark as per specification confirming to IS:7098 (Part - I) but excluding GST. Makes : Torrent / Universal / Polycab /Gloster. Supply and fixing of Automatic Street Light Control System with Optical Sensor, Low volatage / High voltage trip and reset, operating voltage 380 - 450 V AC, 50 HZ with suitable SMC enclousure of IP 54 protection, MCBs of Legrand / Schneider / L&T / Siemens of 10KA C/D curve and Contactor suitable to control the load of 8KW Three phase load with necessary clamping arrangements including all accessories etc., complete but excluding GST. Makes : Nature switch / Light Mate / Havells Fabrication, transportation, and supply of 16 Mtrs Polygon High Mast with two sections of Bottom 4mm thick and Top section with 3mm thick with GLS type aviation lamp of Bottom 360mm and Top 150mm dia with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate, having a base plate of size 560mm dia 25mm thick with its accessories. Mast shall be in 2 sections and should be hot dip galvanized and suitable for wind velocity of 180 KMPH as per IS 875 part 3 including head frame, 2 point suspension system with steel rope 6mm dia (7/19) construction double drum winch / power tool, and necessary cable trailer connections and single speed motor with M 24 x 800 mm foundation bolts of required quantity, suitable for 6 Flood lights, with GLS type aviation twin lamp 130mm, Top 70mm with 3mm thick, base plate 220 x 220 x 12mm and 4 Nos of M20 x 700mm long J bolts along with template or equivalent including all accessories etc., complete but excluding GST. Makes: BAJAJ / TRANSRAIL. Earth work excavation with an approximate quantity of 6.0 Cum for erecting of 16 Mtrs high mast and refilling with a quantity of 0.65 Cum of PCC 1:4:8, 2.60 Cum M 20 grade concrete and (110 Kgs) reinforced steel of 12mm / 10mm / 8mm, Soil bearing capacity of 10 T/Sqm, Anchor plate with cost and conveyance of all above materials including labour charges for erecting of High Mast and Carriage etc complete including soil testing. but excluding GST. Supply and fixing of suitable out door feeder pillar box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board, suitable angle iron stand for mounting the feeder pillar with cement concrete, including Supply and fixing of Legrand / Schneider make 40A-63A, 4 Pole MCB as incomer,6 Nos 6-32A SP MCBsas out goings indication lamps, din channel, 6 Sq.mm 3 core copper cable for individual light control, connectors, bus bars, shroudings, gland plates and provision for 3 phase energy meter etc., complete for finished item of work and suitable wiring provision for connecting the nature switch. but excluding GST. Supply and transportation of 150 W +/-10% (>=25000 Lumens) LED Flood light Luminaire made of pressure die cast aluminum housing with powder coated, having toughened glass cover, Suitable lens on LEDs, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66 ) protected, wide operating voltage range , P.F > 0.90, System having efficacy >110 lumens/watt, with Ingress protection IP66, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>70, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with 5 years warranty. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates.but excluding GST. LUMINAIRE MAKE : CROMPTON / HAVELLS/ OSRAM LED MAKE : CREE / NICHIA / OSRAM. SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORK, TWO POST CLEAR FLOOR LIFT ( 4 TON CAPACITY) FEATURES : • Bilateral manual safety unlocking system. • The cable and oil pipe Should be fully concealed with decent and elegant appearance. • Double hydraulic cylinder and high strength chain drive shall ensure stable and smooth lifting and lowering. • Wire rope equalization system forces synchronous movement of two carriages and effectively prevents vehicle from tilting. • 24 V low voltage control box (IP54 level) ensures operators safety • 24V cylinder travel limit switch effectively protects cylinder and extends its lifespan • Door rubber pad protects car door from being damaged in collision • More lifting pads with different height meets the requirements for light lorries and SUVs. • Passed 115% dynamic loading test and 150% static loading test • CE certificated • Symmetric installation required.Configuration : PART : SPECIFICATION : Swing arm : 2 stage (800-1200)*4, Unlocking system : Billateral manual pull, Power unit : Domestic (Underneath) 2.2KW 10L, Control Box : Electric control box, Lifting pad : Double screws lifting pad, Safety Device : Cylinder travel limit module, button box, Anti-explosion valve, guardrail, Colour : Launch red, Launch grey, Volkswagen blue, Hyundai blue, GM blue (Buick blue), Warranty : 2 YearTECHNICAL PARAMETERS : Capacity(kg) : 4000, Lifting height(mm) : 1850, Initial height(mm) : 110, Lifting time(s) : <=50, Lowering time(s) - >=20,<=40, Passing width for symmetric installation(mm) : 2436, passing width for asymmetric installation(mm) : 2390-, Overall width for symmetric installation(mm) : 3400, Overall width for asymmetric installation(mm) : 3551-, Overall height(mm) : 3840, Motor power(kw) : 2.2, Motor Voltage : 3 phase/380V or Single phase/220V, Working noise(dB(A) : <=75dB, Working oil pressure (MPa) : 16 Fabrication, transportation, and supply of 16 Mtrs Polygon High Mast with two sections of Bottom 4mm thick and Top section with 3mm thick with GLS type aviation lamp of Bottom 360mm and Top 150mm dia with BSEN - 10025 grade S 355 JO steel plate for shaft, IS 2062 for base plate, having a base plate of size 560mm dia 25mm thick with its accessories. Mast shall be in 2 sections and should be hot dip galvanized and suitable for wind velocity of 180 KMPH as per IS 875 part 3 including head frame, 2 point suspension system with steel rope 6mm dia (7/19) construction double drum winch / power tool, and necessary cable trailer connections and single speed motor with M 24 x 800 mm foundation bolts of required quantity, suitable for 6 Flood lights, with GLS type aviation twin lamp 130mm, Top 70mm with 3mm thick, base plate 220 x 220 x 12mm and 4 Nos of M20 x 700mm long J bolts along with template or equivalent including all accessories etc., complete but excluding GST. Makes: BAJAJ / TRANSRAIL. Earth work excavation with an approximate quantity of 6.0 Cum for erecting of 16 Mtrs high mast and refilling with a quantity of 0.65 Cum of PCC 1:4:8, 2.60 Cum M 20 grade concrete and (110 Kgs) reinforced steel of 12mm / 10mm / 8mm, Soil bearing capacity of 10 T/Sqm, Anchor plate with cost and conveyance of all above materials including labour charges for erecting of High Mast and Carriage etc complete including soil testing. but excluding GST. Supply and fixing of suitable out door feeder pillar box of size made with 14 SWG CRCA sheet with double door arrangement, making powder coating after processing of 7 Tank process, lock and key, hinges, rubber gasket, danger board, suitable angle iron stand for mounting the feeder pillar with cement concrete, including Supply and fixing of Legrand / Schneider make 40A-63A, 4 Pole MCB as incomer,6 Nos 6-32A SP MCBsas out goings indication lamps, din channel, 6 Sq.mm 3 core copper cable for individual light control, connectors, bus bars, shroudings, gland plates and provision for 3 phase energy meter etc., complete for finished item of work and suitable wiring provision for connecting the nature switch. but excluding GST. Supply and transportation of 150 W +/-10% (>=25000 Lumens) LED Flood light Luminaire made of pressure die cast aluminum housing with powder coated, having toughened glass cover, Suitable lens on LEDs, IP 66 (Silicon gasket ensures Optical & Electrical compartments are IP 66 ) protected, wide operating voltage range , P.F > 0.90, System having efficacy >110 lumens/watt, with Ingress protection IP66, Driver surge protection >10KV, THD<15%, CCT: 3000- 6500K as desired by the department and as per IS, CRI>70, Inbuilt Electrical protections like Over voltage, short circuit, Over load, Open Circuit, Miswiring, etc complete with BIS certification with 5 years warranty. The contractor has to furnish the manufacturer warranty letter, LM 79 and LM 80 certificates.but excluding GST. LUMINAIRE MAKE : CROMPTON / HAVELLS/ OSRAM LED MAKE : CREE / NICHIA / OSRAM. MULTIFUNCTIONAL MIG/MAG WELDING MACHINE :Specifications / Requirements:1. Technology: Shall use inverter-based welding technology to provide high welding power with reduced electrical consumption, 2. Design: Compact and lightweight design enabled by inverter technology, reducing the size of internal components compared to traditional transformer-based welders, 3. Warranty: Minimum 2-year on-site warranty.SCOPE OF SUPPLY : Installation, testing, and commissioning of a Microprocessor-Controlled Inverter Wire Welding Machine suitable for MIG, MAG, Flux-Cored, Brazing, and MMA welding applications, equipped with Automatic Thermal Safety (ATS) and advanced control features. The equipment shall be suitable for industrial use and capable of continuous duty under Indian climatic and voltage conditions.2. TECHNICAL SPECIFICATIONS : Parameter : Specification : Type : Inverter-based, Microprocessor-Controlled, Welding Processes Supported : MIG, MAG, Flux-Cored, Brazing, MMA, Input Voltage : 230 V AC ±15%, Single Phase, Frequency : 50/60 Hz, Output Current Range : 20 – 220 Amperes, Welding Wire Diameter (MIG/MAG) : 0.6 mm to 1.0 mm, Flux-Cored Wire Diameter : 0.8 mm to 1.0 mm, Electrode Diameter (MMA) : 1.6 mm to 3.2 mm, Torch Connection Type : Euro Connector, Maximum Spool Size Supported : Up to 300 mm (15 kg spool), Control System : Synergic Control with Pre-set Parameters, Arc-Force Adjustment : Available (for MMA Welding), Protection Features : Thermostatic, Over-voltage, Under-voltage, Generator-Compatible (±15%), Cooling System : Fan-cooled, Duty Cycle : To be specified by the OEM as per IS/IEC 60974, Standards Compliance : IS 1851 / IS 1821 / IEC 60974-1 / IEC 60974-103. FEATURES REQUIRED 07-10-2025 : Microprocessor-based synergic control for welding parameters, Compatibility with multiple materials (Steel, SS, Aluminum, etc.), Protection against voltage fluctuations and overheating, Compact, lightweight, and portable design, Suitable for long-pass welding, Easy operability for semi-skilled personnel, Compatible with generator supply up to ±15% voltage variation.4. SCOPE OF SUPPLY : The following accessories must be included with each machine: Item : Description : MIG Torch : MT15 MIG Torch, 3 Metres, Red, Work Clamp : TOLEDO 250A. Welding Cable : Cable TWO5V-A, 1 x 25 mm², 1.8 Metres, with Plug, Electrode Holder : Suitable for MMA welding, Consumable Kit : Standard spares for initial operation, Aluminum Welding Kit : Suitable for aluminum wire, Operating Manual : In English and Hindi, Warranty Card : With serial number and warranty details5. WARRANTY & AFTER-SALES SUPPORT : Minimum Warranty: 2 years from the date of commissioning, Service Support: OEM or authorized service partner must have service centers in Hyderabad, Spares Availability: OEM must guarantee spares availability for a minimum of 5 years post-warranty.6. COMPLIANCE & DOCUMENTATION REQUIRED WITH BID : OEM Authorization Certificate (if applicable), Technical Data Sheet / Product Brochure, BIS Certificate / Test Certificate conforming to IS/IEC 60974, Declaration of compliance with tender specifications, Self-declaration of non-blacklistingSpecifications : MIG : Power Specifications : 230 V, 50 Hz, Min & Max Current : 20 to 220 A, Max Absorbed Power : 4.8 kW, Load at 60% : 2.7 kW, Wire thickness : 0.6 to 1 mm (steel), 0.8 to 1 mm (Aluminum), Protection degree : IP23, Dimensions : 825 x 360 x 670 mm, Weight : 21 Kg MULTIFUNCTIONAL SPOT WELDINGSpecifications / Requirements: 1. Type & Cooling: Lightweight, water-cooled, single-sided spot welding unit. 2. Portability & Operation: Portable unit designed for ease of operation and quick spot welding. 3. Material Compatibility: Capable of welding mild steel, galvanized steel, and stainless steel materials. 4. Application: Suitable for jobs with throat depth limitations or larger components that cannot be accommodated by conventional spot welding machines, including but not limited to: Stiffener welding on steel structures, Almira doors and shelves, Passenger lift doors and flooring, Welding on square or round pipes, Welding sheets on hollow structures, Cladding of stainless steel sheets or structures.Input Power : 10 KVA, Service Life : 2 Years, Usage/Application : Almira door, Almira shelves, passenger lift doors, flooring of passenger lift etc., Material : Steel, Cooling Water : Yes, Voltage(V) : 415, Automation Grade : Semi-Automatic, Frequency (Hz) : 50, Phase : 2, Rated Input Current(A) : 52, Rated Duty Cycle (%) : 60, Color : Grey, Protection Degree : IP23S, Cooling Transformer Type : Air Cooled, Is It Portable : Portable, Cable Length (mm) : 3000, Rated Input Power (KVA) : 15, Type : Water Cooled, Condition : New, No Load Loss : 48, Country of Origin : Made in India PREPERATION BOOTHSpecifications / Requirements: 1. Purpose: Booth shall be designed for all preparatory work prior to painting, including minor paint jobs. 2. Airflow & Filtration – Sanding/Putty Mode: Extracted air shall pass through a three-stage filtration system and be exhausted to the atmosphere.Type  : Downdraft – 6.3 m, Side wall : Polyurethane Sandwich panel, Panel thickness : 50, Door: PVC Curtain, Blower type : Centrifugal Blower, Blower Capacity : 18000, Motor Power : 5.5/ 7.5, Input Supply : 3Ф, 415V +10%/ – 15%  , 50Hz ±5%, Ceiling filter media size : 5, Pocket filter media size : 10, Maximum capacity of metal base : 3000, Maximum capacity of Grids : 900, No. of Tube lights : 24 (6 Frames with 4 Nos. Tube light each), Tube light power  : 36/ Tube light, Air velocity : 0.2, Required air pressure : 5 – 6, Working temperature : 0 to +70, Overall dimensions (L X W X H) : 6523 x 5190 x 3330, Inner dimensions (L X W X H) : 6300 x 3675 x 2680 WELDING WORK BENCHPlate Material : STEEL-IS2062, Frame Material : STEEL-IS2062, Table Flatness : 0.3/1000mm, Hole Diameter : Φ16mm, Hole pitch : 50±0.038mm, Plate Thickness : 16mm, Niriding case depth : 0.01-0.02mm, Length : 1150 mm, Width : 1200 mm, Height : 750/900 mm 2 WHEELER TIRE CHANGER WITH TUBELESS INFLATION WITH ADAPTER -220VSpecifications : Outside clamping range : 6- 24inch, Inside clamping range : 3- 12inch, Max wheel diameter : 960mm, Working pressure : 8-10 bar, Bead breaking force : 2500 Kg, Power supply : 110V/220V/380V, Motor Power : 0.75kW/1.1.kW, Rotation per Minute : 6.5/13 rpm, Noise : <70dB. WHEEL BALANCER AUTOMATIC WITH ADAPTERSpecifications : Rim diameter : 1 – 28 inch, Max. Wheel weight : 70Kg, Max. Wheel diameter : 1118mm, Rim width : 1.5 – 20, Precision : ± 1g, Motor Power : 90W, Power requirements : 100/230V 1Ph, Rotation per minute : 140rpm, Balancing time : 7s, Second time mounting test : ≤5g. MOTORCYCLE LIFTSpecifications / Requirements : 1. Design: Sturdy lift with a wide platform to accommodate larger and wider motorcycles. 2. Functionality: Shall facilitate efficient servicing of motorcycles while ensuring operator comfort and reducing fatigue.Specifications : Lifting Capacity (Kgs) : 400, Lifting Time (Secs) : 20, Max. Lifting Height (mm) : 900, Min. Lifting Height (mm) : 200, Platform size (LxW)(mm) : 2250 x 750, Safety Mechanism : Mechanical lock, Operation : Electro – Hydraulic, Oil tank capacity (Litres) : 15, Power Pack : Motor Details -0.75 HP, 1PH and Power Supply -230 V / 50 Hz BIKE DIAGNOSTIC TOOLSpecifications / Requirements:1. User Interface: Simple and intuitive menu system allowing easy operation and quick learning., 2. Diagnostic Functions: Shall provide complete diagnostic capabilities, including code reading, code clearing, data flow monitoring, action testing, settings adjustment, and coding., 3. Menu Navigation: Arbitrary menu selection for convenient and quick access to functions., 4. Data Handling: Shall record and play back real-time data flow to assist in accurate identification of sensor and component faults., 5. Connectivity: Wi-Fi connectivity for software updates and remote diagnostics., 6. Remote Assistance: Capability for one-click remote support by technical staff., 7. Vehicle Coverage: Shall support the majority of Asian and European vehicle models.Functions : Operation system : Android 5.1.1, CPU : RK3128 quad-core ARM cortex A7, Battery : 2600mA, rechargeable polymer lithium battery, Extension memory card : 32G micro SD (TF) card supported, LCD : 5.0 inch, LCD resolution : 800*480, Touch screen : Capacitive touch screen, Wifi : Supported, Working temperature : -20℃—55℃ (14℉—131), Storage temperature : -20℃—70℃ (-4℉—158), Weight : About 700g, Dimension : 198mm*115mm*31mm INJECTOR CLEANER MACHINESpecification: •Power supply: AC220V± 10%, 50/60Hz; ·• Ultrasonic cleaner power: 100W, •RPM range: 10--9990rpm; Step: 10rpm, •Time range: 1--9999s, •Pulse width: 0.5--25ms; Step 0.1 ms; •Fuel tank capacity: 4000ml, •Dimensions: 400mm* 410mm*580mm; •Net Weight: 27kg, •Working Temperature: -10~+50°C; • Intensity of outer magnetic field: < 400A/m; MANUAL HEAD LIGHT TESTERSpecifications / Requirements: 1. Operation: Equipment shall be simple and quick to operate. 2. Power: Shall operate without external power supply. 3. Mobility: Optional extra-long rails shall be provided to allow the unit to be moved in drive-through applications. 4. Space Requirement: Shall require minimal space, approximately 50 mm between vehicle headlamp and lens. 5. Documentation: Shall be supplied with installation and operation manuals. 6. Display: Clear and simple aiming screen for alignment.7. Options: Shall be available with or without a Lux Meter; the Lux Meter (if provided) shall operate on pencil cells. 8. Vehicle Compatibility: Suitable for all types of automobiles, including heavy commercial vehicles (optional).Specification : Value : Column Height (Boom) : 1665mm (From T-Base), Lens Diameter : 160mm, Dimension (Cabinet) : 280mm (H) × 243mm (W) × 535mm (L), Measuring Range (From Ground Level) : Max. Height : 1500mm, Min. Height : 240mm, Lux Meter (Optional) : Digital, Indication Available : Lux Values, Lux Meter Range : 10 Lux to 50,000 Lux, Power Supply (Lux Meter) : 9V (6F22) Battery Digital Type, Accuracy : ±10 LuxOptional Accessories: Digital Lux Meter, Large Boom (For HCVs), Set of Rail (4 Pcs.) BRAKE TESTER - PORTABLE Specifications / Requirements: : 1. Application: Shall be suitable for use in automobile manufacturing quality assurance, engineering research, final testing, customer care service centers, as well as transport and logistics companies to ensure braking safety. 2. Test Duration: Each test shall take less than seven minutes; a series of tests shall be completed in approximately 20 minutes. 3. Vehicle Downtime: Vehicle “off-duty” time shall be minimal during testing. 4. Display & Output: Brake efficiency shall be viewable instantly on an LCD display; system shall support printing via IR portable printer and downloading data to a PC for further analysis. 5. Data Storage: Shall store a minimum of 99 test readings for service and hand brakes. 6. Optional Reference: Equipment shall be comparable to widely used systems in India such as those utilized by Linde (BOC), Praxair, Total Oil, ARAI, Tata Motors, Maruti, Brakes India, and others. 3D WHEEL ALIGNMENT MACHINE WITH DUAL DISPLAY, 3G SOFTWARE, HIGH ACCURACY AND SWIFT PERFORMANCESpecifications / Requirements: 1. Camera System: Shall include four high-resolution cameras arranged in a single beam, installed in front of the vehicle. 2. Wheel Targets: Targets shall be attached to vehicle wheels using appropriate wheel adapters. 3. Measurement Principle: System shall use cameras to observe targets and determine the precise position of each wheel in 3D space. 4. Imaging Technology: Digital high-resolution cameras with embedded IR backlight shall enable the software to track the exact spatial positions of all targets. 5. Should be able to perform single flat turnout.FEATURES : Specifications / Requirements: : 1. Target Boards: Durable, impact-resistant, and high-precision target boards. 2. Real-Time Display: 3D model of the vehicle chassis shall display wheel positions and alignment angles in real-time. 3. User Interface: User-friendly interface with help and support system to allow quick learning and operation by new users. 4. Lift Compatibility: Shall support a wide range of working heights, allowing measurements and adjustments from lift height (up to 1700 mm) to floor level without additional camera displacement mechanisms, stairs, or stands. 5. Camera Positioning: Minimum distance from cameras to lift or pit approximately 1200 mm; camera-to-turntable distance from 1200 mm to 2500 mm. 6. Operation: Bluetooth remote control for easy operation. 7. Calibration: Equipment shall not require calibration after installation and shall be ready for use immediately. 8. Auxiliary Display: Shall include an auxiliary target display (VODI) for target setting. Specifications : Camber : ±8° ±3’, Toe : ±5° ±3’, Caster : ±19° ±8’, SAI/KPI 07-10-2025 ±19°±8’, Thrust Angle : ±2.5°±3’, Geometrical Driving Axis : ±2.5°±3’ 18. 3D WHEEL ALIGNMENT MACHINE FOR HEAVY VEHICLESSpecifications / Requirements: 1. Measurement Capability: Shall measure trucks with wheelbases up to 16 meters and PCVs/LCVs with wheelbases greater than 2 meters. 2. Target Recognition: Machine vision system shall automatically recognize targets installed on vehicle wheels. 3. Alignment Modes: Shall support frame reference, axle reference, and baseline reference modes. 4. Compensation: Shall provide four compensation modes, including forward rolling compensation. 5. Target Handling: Targets shall be compact, easy to handle, and not require calibration. Self-centering wheel adapters shall fit wheel sizes from 12” to 24”. 6. Operation: Bluetooth remote control for convenient operation; one-step alignment shall support up to six axles. 7. Camera System: High-resolution wide-scope cameras for precise 3D measurements. 8. Auxiliary Display: Shall include an auxiliary target display (VODI) for target setting. 9. Roll-Out Options: Shall support both jack-up run-out and roll-back run-out measurements. 10. Maintenance: Designed for reduced maintenance compared to older electronic sensor-based 2D alignment machines.Specifications : No. of cameras : 4 measurement digital HD cameras. Power requirements : Voltage 220 ± 10%, 50/60 Hz. Measures : Camber, Caster, Kingpin Inclination, Toe-in, Toe-out, Set back, and Thrust Angle. Camera covering distance : 19m from camera. Run out compensations : Rolling run out, Jack up run out and extended rolling run out. AUTOMATIC TIRE CHANGER 26: WITH ARM ASSISTSpecifications / Requirements: 1.     Functionality: Equipment shall be suitable for servicing a wide range of wheels, including run-flat tyres. 2.     Features: Shall include essential features for efficient tyre changing, ensuring versatility and quick operation. 3.     Usability: Designed for simple and convenient operation. Model: RFT-automatic Tyre changer.Specifications : Motor Power : 0.75/1.1kW, Air Requirement : 8 – 10 bar, Internal Rim Clamping : 12”- 23”, External Rim Clamping : 10”- 20”, Bead Breaker Tire Width : 3”- 15”, Maximum Tire Diameter : 41”, Power Supply : Single Phase WHEEL BALANCER WITH LAZER POINTINGSpecifications / Requirements: 1. Balancing Programs: Shall support DYN/STA and various ALU balancing programs. 2. Motorcycle Compatibility: Shall allow motorcycle wheel balancing using a motorized method with the appropriate adaptor. 3. Customization: Shall enable user-defined settings for balancing operations. 4. Input Parameters: Shall allow input of wheel distance, diameter, and width through clockwise or anti-clockwise rotation. 5. Display: IMD display panel shall be resistant to scratches and erosion.Rim diameter : 1 – 24 inch. Max. Wheel weight : 65Kg. Max. Wheel diameter : 1188mm. Rim width : 1.5 – 20. Precision : ± 1g. Motor Power : 0.25kW. Power requirements : 100/230V 1Ph. Rotation per minute : 200rpm. Balancing time : 10s. Second time mounting test : ≤5g. 4T FOUR POST LIFT FOR WHEEL ALIGNMENTSpecifications / Requirements: 1. Purpose: Shall be suitable for underbody repairs and wheel alignment operations. 2. Safety & Stability: Shall ensure high levels of operational safety and stability. 3. Lifting Capacity: Shall raise vehicles to heights of up to 6 feet, adjustable based on operational requirements.Lifting capacity : 4000 kg, Lifting time : 40 sec, Max. lifting height : 1750 mm, Min. lifting height : 190 mm, Dimension (LxWxH) : 5205 x 3210 x 2235 mm, Oil grade : 68, Oil tank capacity : 8 Litres, Motor power : 2.2 kW, 3 hp, 3 Ph, Power supply : 415 V / 50 Hz, Safety mechanism : Pneumatic Lock, Air requirement : 7 Bar, Adjustment between roller shaft : 900 / 1130 mm, Operation method : Electro - Hydraulic, Lifting capacity : 2000 kg, , Max. lifting height : 495 mm, Min. lifting height : 225 mm NITROGEN GENERATOR FOR SINGLE TYRE APPLICATIONSpecifications / Requirements: Scope of Supply: 1. N2 Nitrogen Inflator unit (NITROFILL). 2. Hose: 10 m hose with clip-on connector.Installation and Operating Requirements: 1. Space: Overall space allocation for the equipment shall be approximately 450 × 523 × 1311 mm. 2. Floor Level: Equipment shall be installed on a firm, level surface within ±20 mm tolerance to ensure stability and prevent vibration. 3. Compressed Air: Air supply pressure shall be maintained between 7.5 and 10 bar.4. Power Supply: Single-phase 230V AC with proper earthing shall be provided.Specifications : Recommended input pressure (kg/cm²) : 12, Pecentage of Nitrogen (%) : >95, Storage tank size (Ltrs) : 60, N2 Generating capacity (lph) : 3,500, Pre set inflation : YesDisplay : 2 LED, Seven Segment, 1LED, Hose system (10 m) : Single Hose, Foot connector : Clip on, On time purity : NA, Inflation mode : N2/Air, Tyre pressure setting range (psi) : 170, Over all dimension (LxWxH) (mm) : 450x523x1311 NITROGEN GENERATOR FOR SINGLE TYRE APPLICATION - HDSpecifications / Requirements: 1. Construction: Equipment body shall be made of mild steel for durability and robustness under varying operational conditions. 2. Vibration & Noise: Shall include anti-vibration coating to minimize operational noise. 3. Operation: Shall have an automatic shutoff function to stop inflow when the desired pressure is reached. 4. Electrical Supply: Working voltage shall be 240V AC; equipment shall support conversion between single-phase and three-phase power as required.Specification : Value : Recommended input pressure (kg/cm²) : 16, Percentage of Nitrogen (%) : > 95, Storage tank size (Ltrs) : 250 (External), N₂ Generating capacity (lph) : 8000, Output pressure (kg/cm²) : 14, Pre set inflation : Yes, Display : Dual LED, Hose system (10 m) : Single hose, Foot connector : Double end connector, On time purity : Yes, Inflation mode : N2, Inflation system : In-Built, Tyre pressure setting range (psi) : 174, Over all dimension (LxWxH) (mm) : 530x400x1350 LOW RISE LIFTSpecifications / Requirements: 1. Function: Shall provide a stable platform that rises vertically to a low or moderate height using a hydraulic scissor mechanism. 2. Minimum Height: Equipment shall have a low minimum height (approximately 6 inches) for easy access. 3. Maximum Lifting Capacity: Shall be capable of lifting heavy loads, including vehicles or industrial equipment, to a maximum height typically between 1-5 FEET. 4. Hydraulic System: Shall use pressurized hydraulic fluid to power cylinders for smooth lifting and lowering of the platform. 5. Applications: Suitable for automotive workshops, factories, warehouses, and material handling operations where low-height lifting is required for maintenance, loading, or assembly work.Specifications: Maximum Load : 4 Ton, Power Source : Electric, Lift Type : Scissor Lift, Material : Mild Steel, Operating Height : 0-5 feet, Color : Red, Surface Finishing : POWDER COATING Truck Tyre ChangerSpecifications / Requirements: 1.     Compatibility: Shall be capable of servicing passenger vehicles, trucks, agricultural vehicles, and industrial vehicle tyres. 2.     Operation: Shall include a portable console for convenient and accurate operation. 3.     Electrical Supply: Three-phase 415V, 50 Hz, 6 HP with proper earthing. 4.     Power Cable: 2.5 sq.mm, 4-core with earth. 5.     Earthing: Resistance below 3 ohms. 6.     MCB: 32 A, 4-pole with earth. 7.     Socket: 32 A, 4-pin with earth. 8.     Compressed Air Supply: 8–10 bar pressure required. 9.     Air Hose: Supplied as required. 10.  Dimensions: Approximately 1570 × 2010 × 1000 mm (L × W × H). 11.  Installation: Fixed type. 12.  Hydraulic Oil: 15 L. 13.  Tyre Wax: 3 kg.Specifications : Max. Wheel Diameter : 59″, Machine weight : 561KG, Wheel Width : 30″, Power : 1.8 KW, Internal Clamp : 14″-26″, Working Pressure : 150bar, Power Supply : Three Phase Compressor -15HP + Drier + Line filterSpecifications / Requirements: 1.     Compressor Model: Screw 2.     Capacity: Free air delivery approximately 52 CFM. 3.     Maximum Working Pressure: 9.5 kg/cm² 4.     Normal Working Pressure: 9.5 kg/cm² 5.     Stages: Single-stage compressor. 6.     Cooling System: Air-cooled. 7.     Main Motor: 11 kW squirrel cage induction motor, TEFC type, suitable for 400V, 3-phase, 50 Hz AC supply; F-class insulation with IP55 protection; service factor 1.15 continuous. 8.     Starter: Star Delta starter. 9.     Dimensions: Approximately 875 × 800 × 1008 mm (Length × Breadth × Height). 10.  Weight: Approximately 280 kg.SCOPE OF SUPPLY : Ø Base & Enclosure: o Quiet enclosure, o Rigid frame , o Powder-coated panels. Ø Drive System: o Main motor – 400V 50Hz IE1 TEFC Sq. cage induction motor, o Belt drive with tensioning adjustment Ø Encapsulated System: o Encapsulated airend with major systems integrated, a. Air inlet system, i. Closed type air filter , ii. Intake valve with capacity control iii. Solenoid valve iv. Blow down valve b. Compression system i. Highly efficient airend with -v profile rotors c. Air/oil separation system i. Air/oil separator tank incorporating OSBID principle ii. Spin-on type separator element (EN2 – EN30) iii. Minimum pressure valve iv. Pressure relief valve v. Oil sight glass vi. Thermal valve vii. Oil drain valve d. Lubrication system i. Spin-on type oil filter Ø Cooling System: o Air/oil cooler o Cooling fan with integrated motor Ø Control System: o Neuron micro controller o Emergency shut down o IP 54 control panel o Pressure transmitter o Temperature sensor AIR DRYER : Automation Grade : Automatic, Voltage : 220V Capacity : 50 CFM, Dryer Type : Refrigeration Dryer, Air Flow Rate : 50 CFM, Maximum Pressure : 16 BAR, Maximum Air Inlet Temperature : 45 DEG C, Control : AUTOMATIC, Working Pressure : 7 BAR VERTICAL TANK - 2000L WITH AUTO DRAIN VALVE - 11BAR PRESSURE Specification : Details : Capacity : 2000 Liters, Orientation : Vertical, Material : Mild Steel (MS), Stainless Steel (Optional), Design Pressure : 8-12 Bar (Customizable), Tank Coating : Anti-Corrosion Coating, Testing : Hydrostatic and Pneumatic Tested, Accessories : Safety Valve, Pressure Gauge, Drain Valve, Finish : Powder Coated/Primer Painted, Compliance : ASME/IS 2825 Standards, Usage : Compressed Air Storage in Industrial and Commercial Applications 500L PISTON COMPRESSORSpecifications / Requirements: 1. Drive System: Integrated drive with compact top block design. 2. Cooling System: Larger aluminum inter- and after-coolers providing approximately 32% more heat transfer area .3. Duplex Model Feature: Top block shall be operable independently for demand-based utilization. 4. Noise & Efficiency: Low noise level; reduced oil consumption by approximately 57% compared to belt drive models. 5. Space Efficiency: Approximately 12% space saving compared to belt drive models.Horse Power : 5 HP, Air Tank Capacity : 220L, Power: 3 phase Maximum Flow Rate(CFM) : 17.7, Compressor Technology : Reciprocating Compressor, Number Of Cylinders : 2, Motor Speed : 925 RPM, Spares Available : Yes, Country of Origin : Made in India ELECTRIC BRAKE OIL BLEADERSpecifications / Requirements: 1. Tanks: Shall include two tanks—one for waste oil and one for fresh oil. 2. Operation: Shall be capable of suctioning waste oil from the brake oil filling cap. 3. Bleeding Pressure: Shall operate at a maximum pressure of up to 2 bar. 4. Components: Shall include a heavy-duty regulator and pump for reliable operation. 5. Mobility & Construction: Shall have a robust body with heavy-duty wheels for ease of movement.Device Specifications : Fluid Capacity: 10 liters, Pressure Hose Length: 3.5 meters, Power Cable Length: 5 meters, Power Requirement: 230 V / 50-60 Hz / 230 W, Regulated Pressure Gauge: 0 to 3.5 bars (Adjustable), Automatic Low Fluid Shut Off: Activates at 1 liter, Weight: 16 kgs AUTO COOLANT CHANGERSpecifications / Requirements: 1. Function: Equipment shall be capable of flushing and replacing engine coolant in a systematic and environmentally friendly manner. 2. Connection: Shall connect through the upper radiator hose for servicing vehicle cooling systems. 3. Operation: Shall remove old coolant completely from the radiator, engine block, and heater core and replace it with new coolant mixture in a few simple steps. 4. Safety & Efficiency: Shall provide a safer, faster, and cleaner fluid exchange process compared to manual draining. 5. Vacuum System: Shall include a vacuum feature for radiator depressurization and reservoir fluid evacuation.Capacity : 20 Litres, Voltage : 230V 50Hz, Automation Grade : Automatic, Material : Mild Steel, Power : 200W, Weight : 60 Kg, Working Pressure : Can be varied, Warranty : 12 Months, Country of Origin : Made in India, Pipe Length : 3 M, Feature : Utility Box TRUCK LIFT 16 TONSSpecifications / Requirements: 1. Lifting Capacity: Shall be suitable for lifting and washing commercial vehicles up to 16 tons. 2. Design: In-ground hydraulic hoist, versatile for multiple applications. 3. Functionality: Shall be capable of hoisting, washing, and lubricating all types of heavy commercial vehicles.Specifications : Lifting Capacity : 16000 Kgs, No.of Plunger : 2 No, Plunger Diameter : 320 mm, Max.Lifting Height : 1525 mm, Operating pressure : 12 to 16 Kg/cm2, Parameter : Value, Capacity (tons) : 16, No. of posts : 2, Plunger diameter (mm) : 320, Operating pressure (Kg/cm²) : 12 to 16, Lifting height (mm) : 1525, Ramp length - Front (mm) : 7620, Ramp length - Rear (mm) : 5800, Ramp width (mm) : 1500, Oil fill capacity (liters) : 520, (Other values) : 820 AUTOMATIC CARWASH WITH DRIER AND COLOR FOAM SPRAY (WITHOUT BRUSH)Specifications / Requirements: 1. Function: Equipment shall be suitable for washing passenger vehicles. 2.Operation Time: Shall enable a complete wash in less than 3 minutes. 3.Safety & Durability: Shall include ultrasonic sensors, torque limiter, corrosion-resistant design, and foam stoppers. 4.Features: Shall include an integrated under-chassis washer for comprehensive vehicle cleaning. 5.Automatic Vehicle Sensing: Shall include automatic vehicle length detection. 6.Wash Duration: Shall provide quick wash cycle times. 7. Safety Features: Shall include a torque limiter and soft PE foam stoppers for operator and vehicle safety. 8. Resource Efficiency: Shall have low water and power consumption per vehicle.Machine Type : Overhead carriage Dual swing arm type, Required space, mm (LxWxH) : 7000 x 3800 x 3100, Overall dimension, mm (LxWxH) : 6560 x 3710 x 3010, Maximum washable dimension of car, mm (LxWxH) : 4900 x 2300 x 1900, Operating system (water) pressure, bar : 16, Water consumption per car, litres : 80 – 105, Shampoo consumption per car, ml : 40 – 60 and (Recommended dilution: 1:135 ), Cycle time per car, min (Excluding manual wiping) : 2 – 2.7, Input supply : 30, 355V – 415V, 50Hz, Total connected load, kW : 5.1, Total operational load, kW : 4.34, Power consumption per car, kWh : 0.08 – 0.1 MANUAL CAR WASH SYSTEM WITH CAR WASH LIFT 6 TONS (LMV) (COMPRESSOR NOT INCLUDED)Specifications / Requirements: 1. Function: Equipment shall be suitable for lifting, washing, and lubricating all types of passenger and commercial vehicles. 2.Models: Shall be available in the following configurations: o   Fully hydraulic model, o   Independent model with a separate intermediate oil reservoir, o   Semi-hydraulic modelSpecifications : Lifting Capacity, No. of Plunger, Plunger Diameter Max. Lifting Height, Operating Pressure, Parameter, Capacity (tons), No. of posts, Plunger diameter (mm), Operating pressure (Kg/cm²), Lifting height (mm), Ramp length - Front (mm), Ramp length - Rear (mm), Ramp width (mm), Oil fill capacity (ltrs), CAR WASHER - WASHING MACHINE - HIGH PRESSURE - MADE IN INDIASpecifications / Requirements: 1. Application: Equipment shall be suitable for daily use in automotive garages, construction sites, industrial facilities, mining, and agricultural applications. 2. Functionality: Shall be designed for high-pressure washing applications, including commercial vehicles, construction equipment, and dumpers.Specifications : Models (P 36/40**) : Displacement (lpm) : 50, Delivery per gun (lpm) : 22, No. Of Guns : 2, No. Of Plungers : 3, Operating Pressure (Bar) : 40, Motor Power (Hp) : 10, Pump Speed (rpm) : 400, Type of mounting : Base, Suction Type : Positive ELECTRICAL TESTING BENCH BIG ALONG WITH BENCH WISE AND GRINDERSpecifications / Requirements: 1. Input Power: 3-phase, 415V AC, 32A, 50 Hz. 2. Alternator Test Capacity: 200 MPS/12V, 200 AMPS/24V. 3. Starter Test Capacity: 200 MPS/12V, 24V. 4. Motor: 10 HP, 3-phase, 415V. 5. Meters: All-digital display for monitoring electrical parameters. 6. Alternator Testing: 7. Variable speed test for alternator. 8. Excitation from source or battery. 9. 0–6000 RPM alternator testing range. 10. RRM (Regulated RMS) reading. 11. W-terminal reading. 12. Battery Testing: 13. Battery charging current measurement. 14. Variable voltage for battery charging. 15. Series Lamp Test: Facility for series lamp testing. 16. Solenoid Test: Shall include solenoid testing facility. 17. Construction: Heavy-duty rugged frame and mounting for durability and stability. Electrical testing Bench SmallSpecifications / Requirements: 1. Input Power: 3-phase, 415V AC, 15A, 50 Hz. 2. Alternator Test Capacity: 140 MPS/12V, 100 AMPS/24V. 3. Starter Test Capacity: 150 MPS/12V, 24V. 4. Motor: 5 HP, 3-phase, 415V. 5. Meters: All-digital display for monitoring electrical parameters. 6. Alternator Testing: 7. Two-speed alternator test. 8. Excitation from source or battery. 9. W-terminal reading. 10. Vacuum pump testing for alternators. 11. Battery Testing: 12. Battery charging facility from test bench. 13. Battery charging current measurement. 14. Series Lamp Test: Facility for series lamp testing. Alternator & Self StarterTesting BenchSpecifications / Requirements: 1. Input Power: Single-phase, 230V AC, 15A, 50 Hz. 2. Alternator Test Capacity: 80 AMPS/12V, 50 AMPS/24V. 3. Starter Test Capacity: 100 MPS/12V, 24V. 4. Motor: 2 HP, single-phase. 5. Meters: All-digital display for monitoring electrical parameters. 6. Alternator Testing: Two-speed alternator test. Excitation from source or battery. 7. Battery Testing: Battery charging facility from the test bench. Relay testing UnitSpecifications / Requirements: 1.    Function: Equipment shall be suitable for testing various relays for their time-current characteristics. 2.    Input Power: 230V AC, single-phase, 50 Hz. 3. Output: o   Voltage Source: AC voltage 0–230V, 2A and/or DC voltage 0–230V, 2A. o   Current Source: 0–5–25–50A with multiple taps for selection. o   Time Measurement: Shall include a time interval meter for accurate measurement of relay operation. 4.    Testing Capability: Shall be suitable for testing the above electrical parameters of relays. BENCH DRILL MACHINE Specifications / Requirements: 1. Brand & Origin: Generic, made in India. 2. Motor Power: 1.5 HP, 220–240 V, 50 Hz, 1.49 kW input. 3. Drill Capacity: Up to 40 mm (1.6 inches). 4. No-Load Speed: 1500 rpm. 5. Drill Chuck: 40 mm. 6. Working Surface: Table size approximately 355 mm. 7. Dimensions: Approximately 914 × 1524 mm (B × H). Weight: Approximately 84.5 kg. ADVANCED LATHE MACHINE ALONG WITH REQUIRED TOOLS (THREADING TOOLS ETC)Parameter : Value : Swing over bed : 180 mm, Distance between centers : 200/300/350 mm, Hole through spindle :20 mm, Cross slide travel : 65mm, Compound travel : 55 mm, Spindle taper : MT3, Tailstock taper : M12, Spindle speed low range : 100–1100 ±10% rpm, Spindle speed high range : 100–2500 ±10% rpm, Motor output power : 250 W, Range of thread metric version : 0.4–2.0 mm (10 thread pitches), Imperial version : 12–52 TPI (18 thread pitches), Overall dimension (LxWxH) : 700x300x300 mm, Weight (Net/Gross) : 40/42 kg, Packing Size : 790x360x390 mm ON Car brake lathe (Disk Skimming)Specifications / Requirements: 1. Operation: Equipment shall attach directly to the vehicle hub for on-vehicle disc machining. 2. Accuracy: Shall include an electronically controlled gyroscope system to measure and correct hub run-out up to 0.05 mm. 3. Machining Time: Automatic surface machining of a disc shall be completed in approximately 4 minutes, with the total process taking less than 9 minutes per disc. Parameter : Value : Maximum Rotor Thickness : 1.75, Minimum Rotor Thickness : 0.2, Maximum Rotor Diameter : 16.2, Minimum Rotor Diameter : 4, Maximum Depth of Cut : 0.020/ Side, Spindle Speed : 123 RPM, Carriage Speed : 0.005/ rev. Motor : 1.00 HP, Weight : 76 lbs., Electrical Supply : 120V / 1ph / 60Hz, Shipping Weight : 175 lbs. LINEAR REVETING MACHINEMaterial : Metal plate, Painting : High quality paint, Color : Blue&black, Max rivet force : 60KN(6T), Working air pressure : 0.8-1Mpa(Adjsutable), Suitable rivet diameter : 3-10mm, Stroke of the riveter : 40mm, Accessories: Riveters: 6pcs, used for working on Φ3, Φ4,Φ5,Φ6,Φ8,Φ10 rivets, Puncher: 2pcs, used to remove old rivets 3mm-10mm HYDRAULIC SHOP PRESS HEAVY DUTY 50 TONSMax Force Or Load : 60 ton, Model Name/Number : 50 Ton hydraulic press, Automation Grade : manual, Material : Mild Steel, Voltage (V) : 220, Return Force (kN) : 100, Usage/Application : Manual, Control Type : Non CNC, Color : Orange & Greys, Cnc Or Not : Not, Frame Type : H type, Overall Height : 77, Packaging Type : Not, Weight Kilogram : 500 kg, Type Of Press : H type, Hydraulic Presses Force : 50 Ton capacity, Piston Head Diameter : 80mm, Country of Origin : Made in India HYDRAULIC SHOP PRESS - 10 TONSCapacity : 10 Ton, Type of Product : Hydraulic Shop Press, Model No : PS158, Product Sub Type : With Gauge, Working Range : 135 mm, Max. Displacement : 358 mm, Net Weight : 51 Kg, Country of Origin : IINDIA, Type of Product : Hydraulic Shop Press with Guage, Material : Steel, Model No :KCSP10T-G, Working Range : 0-330 mm, Dimension : 760x530x160 mm, Weight : 51 Kg, Name of Manufacturer/ Packer/ Importer : Ga, Lifting Capacity (Kg) : 10000 Kg High end Diagnostic tool for cars HCVSpecifications / Requirements: Functionality: 1. Equipment shall provide full-function intelligent vehicle diagnostics for heavy-duty trucks, buses, and commercial vehicles. 2. Shall support comprehensive system diagnostics, calibration, and special functions including, but not limited to: idle speed adjustment, speed limit, cruise control, PTO, exhaust brake valve, EGR valve tests, DPF regeneration, SCR system tests, cylinder cut-out, injector testing, air pressure module calibration, and other engine and vehicle system parameters. 3. Shall support X-431 ADAS calibration for advanced driver-assistance systems. 4. Shall allow remote diagnostics enabling operation without being physically on-site. 5. Shall include integrated vehicle service and repair database, with lookup for vehicle coverage across US, Asian, and European makes and models. 6. Shall support one-click software upgrade and silent installation.Vehicle Coverage: Shall support a wide range of heavy-duty vehicle manufacturers including Ashok Leyland, Bharat Benz, Tata Motors, Eicher Motors, Delphi, Scania, Isuzu, Wabco ABS, Caterpillar, Cummins, Denso Diesel, MAN, Bosch, Hino, Volvo, Maxxforce, Benz (India), Siemens, John Deere, Miller, Iveco, Iris Bus, Kobelco, Kenworth, and others. Hardware & Operating System: 1. CPU: 1.8 GHz, 8-core processor. 2. Operating System: Android 9.0. 3. Memory: 32 GB (expandable to 128 GB). 4. Display: 10.1-inch screen. 5. Connectivity: USB, Bluetooth, and Wi-Fi. 6. Heavy Duty VCI Module (X-431 HD III) for 12V–24V vehicle support. High end car Diagnostic Scanner with 10 years UpdatesSpecifications / Requirements: 1. Functionality: shall provide comprehensive oe-level vehicle diagnosis. 2. Vehicle compatibility: shall support electric vehicles, passenger cars, and heavy-duty vehicles. 3. Communication protocols: shall support can, can fd, doip, and j2534 protocols. 4. Remote diagnostics: shall include smartlink remote diagnostic capability. 5. Service functions: shall provide at least 41 advanced service functions. 6. Programming: shall support advanced programming options, including key programming. 7. Database access: shall provide access to x-431 fix* database. 8. Module mapping: shall support topology module mapping. 9. Durability: equipment shall have ip65-rated protection against dust and water. 10.  Ports & Connectivity: Shall include Type C, Type A, DC IN, Micro SD, and Mini HDMI ports for device connectivity and charging. 11.  Diagnostic Interface: Shall include a DB15 interface for professional vehicle or engine diagnostics. 12.  Network & Data: Shall include LAN/WAN port, Data I/O port, and DC-IN power jack for network connectivity and power supply. 13.  Operation Controls: Shall include a power/screen lock key for screen operation and power management. 14.  Stand: Shall include a 0°–180° adjustable kick-stand for convenient positioning. 15.  Thermal Management: Shall include visible heat sink for effective device cooling.Specification : Details : Operating System: Android 13, CPU : 2.0 GHz, Octa-Core, Memory : 12G, Storage : 512G, Display : 13.6 inch, 2560x1600, Battery : 9,360 mAh @ 7.6V / 71.1 Wh, Camera : Rear 20MP, Front 8MP, VCI Connection : 2.4GHz & 5GHz Dual Wi-Fi, Interface : Type C, Type A, DC IN, Micro SD, Mini HDMI, Size : 37724635 mm INDUSTRIAL WASHING MACHINE (15KG SPINNER AND WASHER)Capacity : 15kg, Loading Type : FRONT Loading, Usage/Application : Related to laundry, Motor Power : 1 hp, Size/Dimension : 22/26 inch, Cycle Timing : 15 min, Max Temperature : NA, Washing Type : 15 min, Water Consumption : 50 lit., Weight : 150kg, Voltage : 220v, Phase : 1, Working Capacity Kg Per Hour : 50kg, Efficiency : 50-60Hz, Convenience : to do laundry together, Display : NA, Automation Grade : Semi Automatic Warranty : 1 YEAR, I Deal In : New Only, Country of Origin : Made in India STEAM WASHERSpecifications / Requirements: 1. Function: Equipment shall clean vehicles using high-temperature steam for both exterior and interior surfaces. 2. Water Efficiency: Shall use minimal water (approximately 1–2 gallons per vehicle) compared to traditional washing methods. 3. Environmental Impact: Shall require minimal chemical usage for eco-friendly operation. 4. Cleaning Performance: Shall effectively remove grease, dirt, and stains, including hard-to-reach areas, without abrasive scrubbing. 5. Surface Safety: Shall be gentle on vehicle paint and surfaces. 6. Drying: Steam shall evaporate quickly to reduce drying time. 7. Interior Cleaning: Shall be capable of cleaning and disinfecting upholstery, seats, and carpets. 8. Waste Management: Shall leave no standing water, suitable for areas with limited drainage. 9. Operational Requirements: Requires electricity for steam generation.Pressure Capacity : 10 bar, Preheating Time : 4mins, Model Name/Number : 10.2, Steam Capacity : 0.5 ltr / minute, Motor Power : 300 WATTS, Body Material : Stainless Steel, Hose Length : 10 MTR, Operating Temperature : 10 BAR, Diesel Fuel Tank Capacity : 20 LTR, Fuel : DIESEL, Steam Generator : Diesel fired Ride on Battery Operated Scrubber DryerTechnical Specification : Ride on Scrubber Dryer, Machine Type : Battery Operated, Battery Make : AMARON QUANTA, Total Power : 1500 watts, Battery Voltage : 2 X 12 V, 100 AH, Charging Time : 6–8 Hours, Running Time : 3 Hours, Drive Motor : 500 watts, Max Water Consumption : 3.5 Litres / Minute, Cleaning Width : 560 mm, Working Capacity : 3200 Square Meter / Hour, Suction Squeeze Width : 780 mm, Clean Water Tank Capacity : 70 Litres, Dirty Tank Water Capacity : 75 Litres, Noise Level : 67 dBA, Overall Dimension : 1235 x 670 x 1050 mm MACHINE - FULLY AUTOMATIC, WITH UV DYE TEST - R1234YF GAS - WITH LCD DISPLAY AND PRINTER(FOUR WHEELER)Specifications / Requirements: 1. Alarms: Shall include high-pressure alarm, full bottle alarm, and empty bottle alarm. 2. Service Alerts: Shall provide acoustic and visual indications for maintenance and filter replacement. 3. Bottle Filling: Shall include automatic onboard bottle filling. 4. Leak Detection: Shall perform automatic leak checks following the vacuum phase and trigger an alarm upon leak detection. 5. Gas Management: Shall automatically discharge non-condensable gases from the bottle. 6. Vehicle Database: Shall include an integrated database with the ability to add new vehicle models. 7. Oil Management: Shall include an electronic weighing scale for used and new oil. 8. Software: Shall include a port for software updates. 9. Refrigerant Management: Shall have a simplified refrigerant management system. 10. Output: Shall provide printout functionality. 11. Security: Shall include password protection.Refrigerent Type : R134a, Service Procedure : Fully-Automatic, Display : Graphic, Scale Resolution : 10g, Vacuum Pump : 84 l/min, Recovery Speed : 300 g/min, Refrigerent bottle capacity : 12 liters (Refillable), Hoses : 3m, Working Temperature : 10/500, Power supply : 230 V AC – 50 Hz GAS RECYCLING SYSTEM HD(FOUR WHEELER)Weight : 80 kg, Power Source : 220 V,50 Hz/ 700 W, Dimensions : 560*640*1190 mm, Scale Resolution : 10 g, Vacuum Speed : 5.4 m3/hrCharge Speed : 800 g/min, Cylinder capacity : 10 kg, Filter ability : 150 kg, Optimal operating range : 11 to 49 degree C, Recovery Speed : 250 g/min WATER RECYCLING SYSTEM- EXCLUDING LOCAL CIVIL WORKS & ARRANGEMENTS (EPT)Specifications / Requirements: Functionality: 1. Equipment shall produce pure, sterile, pyrogen-free distilled water suitable for laboratory, pharmaceutical, and industrial applications. 2. Shall use a multicolumn distillation system with multiple-effect distillation columns made of SS 316L material. 3. Shall operate fully automatically, without rotating parts, with rapid warm-up and high operational reliability. 4. Shall include automatic dumping of sub-standard distillate. Scope of Supply: 1. Four distillation columns with condensers. 2. One multistage feed water pump (SS 316). 3. Suitable stainless steel frame for mounting the columns. 4. Two flow meters for monitoring water flow. 5. Validation data for distilled water quality. 6. SS 316 cooling water pump (for higher capacity models). 7. SS surge tank with float valve and low-level indicator. 8. Tri-clover sanitary fittings on all pipelines. 9. Conductivity meters on feed water and distilled water lines.Operational Requirements: 1. Water: Deionized feed water with maximum conductivity of 5 μS/cm. 2. Cooling Water: Hardness not exceeding 90 ppm as CaCO₃.Salient Features: Compact and space-saving design. Meets GMP and FDA standards. Silent and easy operation. Energy efficient. High degree of finish. Easy to maintain and operate. Distilled water plantSpecifications / Requirements: Functionality: 1. Equipment shall produce pure, sterile, pyrogen-free distilled water suitable for laboratory, pharmaceutical, and industrial applications. 2. Shall use a multicolumn distillation system with multiple-effect distillation columns made of SS 316L material. 3. Shall operate fully automatically, without rotating parts, with rapid warm-up and high operational reliability. 4. Shall include automatic dumping of sub-standard distillate.Scope of Supply: 1. Four distillation columns with condensers. 2. One multistage feed water pump (SS 316). 3. Suitable stainless steel frame for mounting the columns. 4. Two flow meters for monitoring water flow. 5. Validation data for distilled water quality. 6. SS 316 cooling water pump (for higher capacity models). 7. SS surge tank with float valve and low-level indicator. 8. Tri-clover sanitary fittings on all pipelines. 9. Conductivity meters on feed water and distilled water lines.Operational Requirements: 1. Water: Deionized feed water with maximum conductivity of 5 μS/cm.2. Cooling Water: Hardness not exceeding 90 ppm as CaCO₃.Salient Features: Compact and space-saving design. Meets GMP and FDA standards. Silent and easy operation. Energy efficient. High degree of finish. Easy to maintain and operate. Radial DrillingSpecification : Details : Drilling Diameter : 25 - 60 mm, Reverse Rotation : Yes, Item Weight : 200 kg, Variable Speed : Yes, Warranty : 1 Year, Automatic Grade : Semi-Automatic, Overall Height : 2250 mm, Power Consumption : 3728 W, Drilling Capacity : 25 mm, Pillar Diameter : 130 mm, Spindle Nose to Table Distance : 675 mm, Spindle Nose to Base Distance : 875 mm, Spindle Center to Pillar Surface Dist. : 635 mm (Max), Taper in Spindle : MT-3, Number of Speeds : 8 Speed, Speed Range : 130 - 2600 RPM, Table Size : 200 x 200 x 255 mm, Base Size (Machined Area) : 585 x 915 mm, Overall Base Size : 610 x 940 mm, Spindle Travel : 185 mm, Pillar Length : 1265 mm, Overall Height with Pulley Guard : 1700 mm, V-Belt Section : B - 43, A - 23, Weight : 475 KGS, Motor Power : 1 HP & 0.5 HP Vinyl PRINTERSpecification : Details : Printhead configuration : PrecisionCore MicroTFP printhead, 9,600 nozzles, Maximum print speed : 119.4 m簡/h, Minimum ink droplet volume : 4.3 pl, Maximum print resolution : 1200 x 1200 dpi, Media width : 300 to 1,625.6 mm (64), Maximum media thickness : Less than 1 mm, Roll outer diameter : Up to 250 mm, Reel outer diameter : Up to 250 mm, Roll weight : Up to 45 kg, Ink : Ultra Chrome GS3 ink, Number of inks : 11 colours (C, M, Y, K, Lc, Lm, Lk, Or, R, Gr, Wh/Cl), Ink capacity : 1500 ml, Print speed (default) : PVC: 14.0 m簡/hr (10 pass), Film: 7.2 m簡/hr (17 pass) and Banner: 20.1 m簡/hr (6 pass)Connectivity : SuperSpeed USB, 100BASE-TX/1000BASE-T (Recommended), Control panel : 10.9 cm (4.3) Optical Touch Colour LCD, Dimensions : W: 2,620 mm, Weight (without ink cartridge) : H: 1,021 mm, D: 925 mm (max. 1,004 mm for operation) andd 342 kg, Voltage : AC 100-120 V or 200-240 V 50/60 Hz, Warranty : 2 years onsite, Auto media setup : Yes CUTTING PLOTTERMax Cutting Width : 54 inch, Max Cutting Speed : upto 400 mm/sec, Max Cutting Force : 600 gf, Imaging technology : vector file and read and cut, Product description : 130 Cutting plotter High Cutting Pressure:The machine boasts a cutting pressure of 500g, enabling it to handle a wider variety of materials.Fast Curve Cutting:Users praise the speed and efficiency of the plotters curve cutting capabilities, leading to increased productivity LAMINATIONAutomation Grade : Automatic, Laminating Speed : 10m/min, Warranty : 12 Month, Voltage : 220V, Weight : 230/180 kg, Type : Laminating Machine, Roller diameter : 130 mm, Driven Type: Electric, Dimension(L*W*H) : 215 x 80 x 74 CM, Max laminating width: 1620 mm, Max laminating thickness: 35 mmProduct Application:- Professional equipment in the printing and post-processing, cater to your varying needs, widely used in the advertising, exhibition organizers, picture production, studio and many other fields, become the most ideal corollary equipment of digital printing products.Main Features:- 1. Hot cold lamination , max 60C, 2. Sillicone rolls , Dia is 130mm, silicone thickness : 6mm which can bear the high temp and long time use at high temp , and anti-sticker, 3. Roller lifting by the air cylinder , which can ensure the same gap between the two rolls, 4. Tension system for the printing peper and the lamination paper, avoid the wrinkle, 5. Two lamination mode, auto and footpadle, 6. Film can go forwards and backwords, 7. Speed : 0-6m per mins, 8. Finger protection system, 9. One year warranty PASTING TABLEMaterial : Metal, Shape : Rectangle, Design : Standard, Dimensions : 3000mm*1500mm, Load capacity : 400kg, Height : 3.5 feet COMPUTEROperating System: Windows 11, Processor Brand: Intel CPU, Number of Cores: Dual-core, Graphics Processor: Intel GPU, Monitor Resolution: 1920 x 1080, Colour: Black, Hard Drive Type: Solid State Drive, Processor Speed: 1.2 GHz processor, Installed Memory: 8 GB RAM, Drive Capacity:512 GB Storage, Monitor Size: 23.8 inch screen, With mouse and keyboard SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKIMPACT WRENCH HOLDERColour : ‎Silver, Material : ‎Stainless Steel, Item Weight : ‎181 g, Head Style : ‎Hex, Finish Type : ‎Unpolished, Operation Mode : ‎MANUAL, Country of Origin : ‎USA, Package Dimensions : ‎17.4 x 11.1 x 10.4 cm; 181.44 g, SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKLED LIGHTColour : Yellow, Material : Stainless Steel, Style : Modern, Light fixture form 08-10-2025 : Floodlight, Room Type : Outdoor, Product Dimensions : 15L x 12W x 12H Centimeters, Specific Uses For Product : Outdoor work projects , Camping , Emergency lighting , Outdoor events ,Hiking and backpacking, Indoor/Outdoor Usage : Outdoor·       Power: 30W, ·       Battery Capacity: 3900mAh, ·       Luminous Flux: 1600 Lumens, ·       Charging Method: USB, ·       Waterproof: Yes, ·       Anti-Fall: Yes, Usage: Outdoor, Work, Camping SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKPTSGP- SPRAY GUN - FINAL FINISHING SPRAYSPECIFICATIONS : AIR INLET PRESSURES P1 = Max. Static Air Input Pressure : 12 bar [175 psi], Vibration Level : <2.5 m/s², ENVIRONMENTAL : Max. Ambient Operating Temperature : 40°C Nominal [104°F]MATERIALS OF CONSTRUCTION : Gun Body Material : Anodised Aluminium, Fluid Tip, Fluid Needle and Trigger Stud : Stainless Steel, Air Cap Material : Electroless Nickel Plated Brass, Retaining Ring, Sprayhead, Adjusting Knobs, Air Valve, Cage, Sleeve : Anodised Aluminium, Springs, Clips, Screws : Stainless Steel, Seals and O-Rings : Solvent Resistant, Trigger : Chrome Plated Steel, Valve Bodies, Rear Housing, Packing Nut, Sleeve Nut : Chrome Plated Brass, Air Valve Stem : Electroless Nickel Plated BrassCONNECTIONS : P1 = Air Inlet Size : 1/4 Universal, P2 = Fluid Inlet Size : 3/8 BSPWEIGHT : GUN ONLY : 470g [16.6 oz]DIMENSIONS : L x H x W mm [inches] : 161 x 177 x 44 [6.3 x 7.0 x 1.7 in] SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKSPRAY GUN FOR PRIMER WITH NOZZLE ADJUSTER - 1.6 to 1.8mmColour : ‎Colorless, Recommended Uses For Product : ‎Painting, Material : ‎aluminium forged, Item Weight : ‎500 Grams, Product Dimensions : ‎16W x 21H Centimeters, Style : ‎1.6 mm, Power Source : ‎Hand Powered, Included Components : ‎Spray Gun, Country of Origin : ‎India SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKAIR FILTER REGULATOR : Material : ‎Aluminium Oxide, Grit Material : ‎Aluminium Oxide, Item dimensions L x W x H : ‎18.5 x 11 x 28.5 Centimeters, Item Weight : ‎1820 Grams, Country of Origin : ‎India, Item Weight : ‎1 kg 820 g, Product Dimensions : ‎18.5 x 11 x 28.5 cm; 1.82 kg, Item Height : ‎28.5 Centimeters, Item Width : ‎11 Centimeters SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKAIR HOSE REEL12MM DIAMETER -Pneumatic pipe for air impact wrench near all the two post lifts(26), four post lift(1). assembled along with trench support. 8mm -10mm pneumatic pipe with 10Meter length supplied and connected to air inlet for dusting air gun. Quantity 28 SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKCONSUMABLESITEMS : QUANTITY : WELDING COILS SS AND MS 1.MM 10KG EACH : 4 EACH, WELDING GLOVES : 10 PAIRS, WELDING GLASS ( BLACK AND WHITE) : 10 PAIRS, , WELDING ROADS : 5 BOXS, FRL OIL : 5 LITERS, PUNCHER KIT MALTI PARPASS : 5 NOS, GREECE : 10 kgs, MICRO FAIBER CLOTH : 10 NOS, 4 INCH CUTTING MACHINE : 25 NOS, HSS DRILL BIT SET : 1NOS, DRILL MACHINE CHECK KEY : 2 NOS, HAND GRANDER CHECK KEY : 2 NOS, TESTER : 2 NOS, OIL PANEL MEDIUM SIZE : 2NOS, CHINNI MEDIUM SIZE : 2NOS SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKSELF VACCUM PNEUMATIC SANDER & HOSEGrit Type : Medium, Power Source : Corded Electric, AC Adapter Current : 4 Amps, Grit Number : 80, Maximum Rotational Speed : 12000 RPM, Item Weight : 1.38 Kilograms, Disc Diameter : 6 Inches SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKGAS WELDING AND CUTTING TORCH KITScope of Supply : 1.  Cutting Attachment (CA79A): o   For use with Acetylene.o   Precision-forged brass head and body. o   Injector mixer design. o   Cutting capacity: up to 1 inch with supplied tip. 2.      Regulators (MR Series) : o   Suitable for gas control. o   Large, single-scale 2-inch gauges for clear visibility. 3.      Welding Handle (WH79): o   With integrated mixer. o   Compatible with Acetylene and alternative fuel gases such as MAP//Pro™, Propane, Propylene, and Natural Gas.Applications / Intended Use: ·       Cutting of steel materials. ·       Automotive, truck, and trailer maintenance. ·       Plumbing works and general repair. ·       Light fabrication, including metal stands and fixtures. ·       Artistic and workshop metal cutting tasks. ·       Heating and bending of metal bars and pipes. ·       Loosening of corroded or rusted fasteners. ·       Repair and maintenance of farm and garden tools.Welding Handle : WH79 w/UM79 Mixer, Cutting Attachment : CA79A, Cutting Tip : 6290A-1, Weld/Braze Tip : TYPE 79E-2, Oxygen Reg. 5-80 PSIG  : MR8210 CGA540, Acetylene Reg. 2-15 PSIG : MR8211 CGA510, Toolbox with Tray : Black Plastic SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKTHERMAL ALUMINIUM DENT REPAIR SYTEM WITH PROJECTED LIGHTSFeatures: Suitable for removal of dents, door dings, and other minor soft dents on vehicle panels. Operates through magnetic induction with flameless heating, eliminating the need for additional consumables. Equipped with a digital screen with adjustable time and power control settings. Enables stress relief on dented panels by localized thermal expansion, allowing effective dent lifting without paint damage. Effective in hard-to-reach areas where conventional tools cannot be applied. Designed for professional automotive body repair workshops to ensure quick, clean, and efficient operation. Reduces repair time and improves cost efficiency for vehicle body shops.Specifications : Input Voltage: 220 V, Input Frequency: 50 Hz, Output Power: 1380 W, Output Frequency: 150 kHz, Power Output Cable Length: 160 cm, Dimensions: 25 × 14 × 8 cm, Net Weight: 3 kg, , Insulation Class: F, Certification: CE, UL, CCC, RoHS, FCC, PSE, Scope of Supply: 1 × Induction Heater, 1 × Accessories Set, 2 × Power Cables, 5 × Candles, SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKTIG WELDING MACHINE SUITABLE FOR ALLUMINIUM WELDINGGeneral Specifications: Phase: Three Phase, Input Voltage: 230 V, Input Voltage Range: 10.1 – 16.8 V Frequency: 50–60 Hz, Automation Grade: Automatic, Weight: 9.1 kg, Degree of Protection: IP23, Availability: In StockTechnical Features: TAC Function: Enables efficient tacking by pulsed arc control, combining two weld pools into one. Particularly effective for welding light-gauge sheets without filler metal. HF Ignition: Provides touchless, high-frequency ignition for arc initiation, ensuring reduced wear and ease of operation.Performance Data (at 40°C, 10 min duty cycle): 170 A / 35%, 135 A / 60%, 120 A / 100%Technical Data: Open-Circuit Voltage: 93 V, Mains Fuse: 16 ADimensions:Width (b): 180 mm, Length (l): 430 mm SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKPORTABLE WEDLING MACHINEGeneral Specifications: 1. Welding Modes: TIG (5–200 A), MMA (20–160 A), 2. Input Voltage: 220 V ±15%, 3. Insulation Class: F, 4. Degree of Protection: IP21, 5. Technology: IGBT Inverter, 6. Cooling System: Fan-basedTechnical Features:1. Dual Welding Capability: Supports both TIG and MMA operations. 2. Advanced Inverter Control: Ensures stable output, high efficiency, and reduced energy consumption. 3. HF Arcing: High-frequency arc initiation for clean and reliable TIG starts. 4. Safety Features: Equipped with Hot Start, Anti-Stick, ARC Force, VRD, and thermal overload protection. 5. High Duty Cycle: Capable of continuous operation at 60% duty cycle for extended welding sessions. 6. Electrode Compatibility: Suitable for electrodes from 1.0 mm to 5.0 mm. 7. Durable Construction: Built with industrial-grade materials for heavy-duty applications. SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKPNUEMATIC RECIPROCATING SAWType of Product : Reciprocating High Speed Saw, Length : 235 mm, Speed : 11000 RPM, Material : Metal, Country of Origin : India, Air Consumption : 28 I/min, Air Inlet : 1/4 (6.35 mm), Hose Size : 3/8 inch, Thread Size: 18 NPT, Hose Size (mm) : 9.525 mm SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKHAND GRINDING MACHINESpecification : Value : Power Input : 800 W, No-Load Speed : 11,000 rpm, Disc Diameter : 100 mm, Spindle Diameter 08-10-2025 : M10, Weight : 1.7 Kg SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKGRINDING TOOLS KITSNo Load Speed : 3800 RPM, Voltage : 220V, Type of Product : Rotary Tool Kit Box, Weight : 0.7 Kg, Dimension : ‎35.5x9.4x29.2 cm, Rated Input Power : 180 W, Chuck Size : 1.6, 2.4 & 3.2, Power : 180 W, Package Contains : 1 x Rotary Tool With 114-pieces Accessories, Wattage : 180W, Country of Origin : India, Suitable For : Carving, engraving, routing, cutting, sanding, grinding, sharpening, drilling, polishing and cleaning, No. of Pcs : 114, Disc Diameter : 4.2 mm, Motor Speed : 0-35000 RPM, Collet Size : 1/6 inch, Weight (g) : 700 g, Chuck (mm) : 40.64,60.96,81.28 mm SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKAIR IMPACT WRENCH (1/2)Specification : Value : Bolt Capacity : M19, Working Torque : 610 Nm, Max. Torque : 680 Nm, Free Speed : 8,000 RPM, Air Consumption : 4.5 cfm, Weight : 2.66 kg SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKHEAVY DUTY AIR RATCHET WRENCH 3/8Specification : Detail : Drive Size :3/8 inch, Usage/Application : Industrial, Country of Origin : Made in India, Torque : 1700 Nm, Type of Product : Impact Wrench, Speed : 4600 RPM, Weight : 7 kg, Air Inlet : 9.525 mm SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORK1/2 AIR RATCHET WRENCH Air Inlet : 1/4 inch (6.35 mm), Type of Product : Air Ratchet Wrench, Net Weight : 1.28 Kg, Drive Size : 1/2 inch (12.7 mm), Air Pressure : 90 PSI, Features : Pin Clutch Impact Mechanism Which Eliminates Torque Reaction, Saving Your Knuckles Three Times Faster than Standard Ratchets Maximum Torque 90 ft.lbs (122 Nm), Length : 280 mm, Hose Size : 3/8 inch (9.5 mm), Torque : 122 Nm, Noise Level : 90 Dba, Country of Origin : Taiwan, Duty Type : Heavy Duty SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKTORQUE WRENCHDrive Size : 1/2 Inch, Usage/Application :Industrial, , Standard : 5_ 23, Kgf.Mtrs : 5_ 23, Nu.Mtrs : 50-220, Ft. Lbs: 40-160 SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKBENCHVICE BigType of Product : Heavy Duty Bench Vice, Color : Black, Material : Cast Iron, Country of Origin : India, Clamping Size : 6 inch SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKBENCHVICE SmallJaw Width : 6 Inch, Type Of Vice : Bench Vice, Material : Cast Iron, Base Type : Swivel, Usage/Application : Industrial, Country of Origin : Made in India SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKENGINE MOUNTING BENCHA general purpose tools that can be used to hold the engine mountings of a vehicle. Material: Iron with rubber grip. Capacity: 50 kg SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKSPARK PLUG CleanerIgnition Coil : 12 KV, Usage/Application : 2 WHEELERS, Weight : 7 KG, Color : RED SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKBIKE SPECIFIC SPECIAL TOOLSThe following tools shall be supplied for use in bicycle servicing and repair: 1. Chain Tool/Chain Splitter – For breaking and reconnecting bicycle chains. 2. Pedal Wrench – Specialized wrench for installation and removal of bicycle pedals. 3. Bottom Bracket Tools – Suitable for installation and removal of bottom bracket assemblies. 4. Crank Extractor – For removal of crank arms from the bottom bracket spindle. 5. Tire Levers – For removal and installation of tires on wheel rims. 6. Cassette Tool and Chain Whip – For installation and removal of rear wheel cassettes. 7. Valve Core Tool – For removal and installation of valve cores in tubes or tubeless stems. 8. Derailleur Alignment Gauge 9. Shock Pump – High-pressure pump suitable for inflating and adjusting air suspension shocks. SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKSANDING VACCUM MACHINEDisc Diameter : 9 inch, 7 inch, Power : 800 W, Warranty : 1 Year, Country of Origin : Made in India, Rated Voltage : 220 - 240 V, No Load Speed : 800-1700 rotations/min, Body Material : Stainless Steel SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKDIGITAL TYRE INFLATOR - WALL MOUNTED DESIGN – LMVGeneral Details : Color : Red Inflation / deflation, Accuracy : +/ - 0.5%, Max Input Pressure ut Pressure : 145 Psi, Max Over Pressure : 185 psi, Pressure Setting Range : 3 - 150 psi, Sensor : Ceramic-based solid-state sensor SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKDIGITAL TYRE INFLATOR - WALL MOUNTED DESIGN - HDInflation / deflation accuracy : +/ - 0.5%, Max Input Pressure : 145 Psi, Sensor Range : 1450 psi, Max Over Pressure : 185 psi, Pressure Setting Range : 3 - 150 psi, Sensor : Ceramic-based solid-state sensor SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKPORTABLE TRUCK TYRE TROLLEYColor : Red, Weight : 120-130 Kilograms (kg), Usage : Loading & unloading, Size : Vary, Equipment Type : Material Handling, Condition : New, Lifting Capacity : 2500 Kilograms (kg), Max. Lifting Height : 110 Millimeter (mm), Feature : Portable, Attributes : Rust Proof, Strong, Durable, Easy To Operate SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKCORDLESS IMPACT 1/2 –Drive Size : 1/2 Inch, Warranty : 1 Year, No Load Speed : : 0-2600 rpm1, Weight : 1.770KG WITH BATTARY, Torque Range : 380Nm, Battery Voltage : : 21V, Motor : Brushless, Voltage : 21V, Battery : 4000mAh/6000Ah Li-ion SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKOIL DRIANER WITH SUCTION AND DRAINER- 90L WITH EXTENSION FUNNELType of Product : Oil Drainer, Color : Blue, Material : Metal, Capacity : 90 L, Package Contains : Plastic tray for holding tools, Finish Type : Gloss, Indicator : Display Oil Level and Air Tank Pressure, Trolly Wheels : 4 No. SUPPLYING, FIXING AND INSTALLATION OF FOLLOWING MECHANICAL EQUIPEMENT WITH DETAILED FEATURES AS MENTIONED BELOW INCLUDING LABOR FOR FIXING, TRANSPORATATION, TESTING ETC., EXCL GST COMPLETE FOR FINISHED ITEM OF WORKCOIL HOSE REEL 15m FOR OIL - HAVE 2 TYPES OF OILParameter : Value : Length : 15 meters, Inner Diameter : 9.50 mm / 3/8 inch, Hose Outer Diameter : 18.1 mm / 23/32 inch, Thread Type : BSPT, Max. Pressure : 2000 PSI, Display : Digital DIGITAL OIL DISPENSING NOZZLEFlow Rate : 0-80 L/Min, Working Pressure : 3 Bar, Motor Power : 550W, Material : Metal, Display : Digital, Features : Easy Operation, Accurate Metering, Auto Shut-Off, Cost Effective, Pilferage Control, Diesel Management, Durable Design PNEUMATIC OIL PUMP HDProduct Specifications : Usage : Industrial, Size : Standard, Product Type : Air Operated Oil Pump, Color : Silver, Material : MS, Structure : Other, Oil Pump DRAWER WORK BENCHMaterial : Mild Steel, Usage/Application : Industrial, Color : Blue, Surface Finish : Powder Coated, No of Drawer : 10, Shape : Rectangular, Country of Origin : Made in IndiaFeatures: ·       Tough steel section framework. ·       Load capacity of each workbench is 1000kgs unified load distribution (UDL). ·       Fully braced for high stability. ·       Tool cabinet with high quality push-button central locking. ·       powder coated  Vehicle Air Filter cleaning machineMaterial : Mild Steel, Power Source : Electric, Voltage : 220V, Color : Red,Orange,Blue,etc VACUUM MACHINE 2 BLOWER MOTORS - WET & DRYMaterial : Stainless Steel, Container Capacity : 30 Litre, Input Power : 1000 Watt, Suction Power : 240 mBar, Surface Recommendation : Surface Cleaning, Hard Floor Cleaning, Air Flow : 100 L/s, Noise Level : 60 dB, Included Components : Suction Blower, Sweeping Brush, Nozzle & Hose Pipe, Weight : 20 kg, Product Type : Vacuum Cleaner, Function : Wet & Dry WASHING GUN (Medium & Big)Weight : 0.2 kg, Dimensions : 20 × 15 × 3 cm·       Multiple Flow Pipe in Gun for Your Different Need. ·       100% Braas Valve And Adapters For Longer Life. ·       ave Time For Washing Car, Bikes And Air Conditioner and many Other Uses. ·       Application:Suitable for Road Cleaning,Car Cleaning, Solar Plant etc. and many more POLISHING & BUFFING MACHINE PNEUMATICType Of Grinder : Pneumatic Angle Grinder, Disc Diameter (Inch) : 6 inch, 5 inch, 7 inch, No Load Speed : 2500 rpm, Spindle Size : 5/8 Inch, Air Consumption : 8 cfm, Air Inlet : 1/4 I, Sound Power : 97.3 / 110.3 dBA FOAM MAKING MACHINEMaterial : Stainless Steel, Type of Product : Pressure Washer, Output Power : 1000W, Thickness : 1.2 mm, Pipe Size : 5 mtr, Tank Capacity : 80 Ltr, Pressure : 1-2 Bar, Warranty Duration : 1 YEAR SHORT BED TROLLEY JACK 3TType of Product : Low Floor Jack, Weight : 31.5-33.5 Kg, Maximum Lifting Height : 485 mm, Suitable For : Lifting Vehicles, Lifting Capacity : 3 Ton, Country of Origin : India, Lifting Height : 485 mm, Minimum Lifting Height : 85 mm, Pump : Dual Pump, Lifting Capacity (Kg) : 3000 Kg LONG BED TROLLEY JACK 3 TONMaterial : Steel, Size/Dimension : T510L: 1010 x 365 x 135mm, Load Capacity : 3 Ton, Color : Red, Quantity Per Pack : 1, Rising Height Mm : 140mm, Weight Kg : 50kgDimensions : T510L: 1010 x 365 x 135mm, T525L: 1150 x 350 x 180mm LONG BED TROLLEY JACK 5T For TrucksCapacity : 5 Ton, Usage/Application : Heavy Duty Vehicle Lifting, Material : Iron, Vehicle Type : Heavy Vehicle, Operating Mode : Manual, Weight Kg : 100 kg, Minimum Height : 155 mm, Maximum Height : 585 mm·       Safety bypass system prevents from damage, ·       Automatic Overload Protection System, ·       Heavy steel frame, ·       Swivel rear castors provide easy maneuverability, ·       Long T Handle for easy positioning JACK STAND 3 TON (Height Adjustable)Color : Red, Product Type : Jack Stand, Material : Mild Steel, Lifting Capacity : 3 Tonne, Application : vehicle lifting, Weight : 6.6 Kilograms (kg) JACK STAND 5 TON (Height Adjustable)Color : Red, Product Type : Jack Stand, Material : Mild Steel, Lifting Capacity : 5 Tonne, Application : vehicle lifting, Weight : 10.8 Kilograms (kg), Min/Max Height : 1.6 ft/4.5 ft 3T FOLDABLE ENGINE CRANE WITH ADJUSTABLE BED HYDRAULICProduct Type : Engine hoist, Dominant Color : Red, Lifting Range : 1-93, Capacity : 3 ton, Boom Length : 40-63, Base Length : 69, Material : Steel, Usage : Engine removal and installation in automotive repair shops and maintenance facilities. Wheels : 6, Features : Heavy-duty, Foldable design, Easy storage, High capacity, Durable steel, Mobile base TRANMISSION JACK FOR HMV (HORIZONTALBreadth : 200 mm, Weight : 98 kg, Maximum Height : 560 mm, Minimum Height : 140 mm, Capacity : 10 Ton, Type of Product : Hydraulic Trolley Jack, Model No : TJ-10, Length : 1450 mm, Country of Origin : India, Name of Manufacturer/Packer/Importer : Everest industrial corporatioI, Capacity (kg) : 50000 Kg TRANMISSION JACK SINGLE PISTONUsage/Application : Automobile, Color : Red, Capacity : 0.5 Ton, Min. Height : 1100 mm, Max. Height : 1900 mm, Net Weight : 30 kgGross Weight : 33 kg, Packaging Size : 1120x220x280 mm, Packaging Type : Plywood Box, Country of Origin : Made in India TRANSMISSION JACK DOUBLE PISTONCapacity : 1 Ton, Material : SS, Color : Red, Weight : 30 kg, Pump : Double 1-TON ENGINE STAND-POWER WRENCHThe engine stand shall meet the following minimum requirements: Load Capacity: Minimum 1-ton, suitable for supporting big block and inline 6-cylinder engines. Mounting Plate: Thick, reinforced mounting plate to ensure secure holding of the engine. Rotation Locking: Provision for minimum 8 locking positions to hold the engine at required working angles. Design: Folding type for convenient storage in limited workshop or garage space. ENGINE SUPPORT 0.5 TONSpecifications : Capacity : 0.5T, Length : 1800MM, G.W / N.W : 16.5 Kg / 15.5 Kg, Package Size : 1850*210*100 mm, 20’ Container : 420 Pcs, Categories AUTOMOTIVE MECHANIC SCETHOSCOPE DIAGNOSTICColour : Black, Exterior Finish : Stainless Steel, Material : Stainless Steel, Item Weight : 0.14 Kilograms JUMP STARTER 12V & 24V AdjustableVoltage : 12/24V, Capacity : 136500mAh, Peak Current : 7000A, Cycle Life : 2000+, Low Temp Start : -40°C, Color : Black, Usage : Jump starts vehicles, 12V and 24V, Features : Safe starting, Strong power, long lifespan, High capacity, Quick charge BATTERY HYDROMETERThe Battery Hydrometer shall meet the following minimum specifications: 1. Specific Gravity Range: 1.100 to 1.300 with a clear, easy-to-read scale (numerical or color-coded). 2. Nominal Voltage Compatibility: Suitable for use with 6V, 12V, and 24V batteries. 3. Construction: Strong, acid-resistant plastic or glass body to ensure durability and resistance to battery acid. 4. Operation: Manual operation with built-in squeeze bulb or suction mechanism for drawing electrolyte samples. 5. Indicator: Internal floating indicator to display specific gravity readings for battery health assessment. 6. Temperature Compensation: Optional provision for automatic temperature compensation for improved accuracy. 7. Accuracy: Capable of fast and reliable testing of battery electrolyte specific gravity. 8. Design: Compact and portable, suitable for both workshop and field use. 9. Maintenance: Maintenance-free design; no regular calibration required. BATTERY HOLDER HANDLEParameter : Dimension : Overall Length (Mounting Plate) : 139.2 mm, Mounting Hole Centers (Horizontal) : 57.5 mm, Mounting Hole Diameter : Ø5.2 mm, Mounting Plate Height : 40 mm, Handle Width (Grip Length) 91 mm, Handle Center Distance (Inner Width) : 104.6 mm, Handle Outer Width : 122 mm AC & DC MULTIMETERCAT Rating : CAT III 600 V, V AC Range : 600.0 V, V DC Range : 600.0 V, Ohms Range : 40.00 MΩ, Auto Shutoff : Y, Continuity : Y, Capacitor : 100.0 μF, Frequency : 100.0 kHz, Hold : No, Duty Cycle : Yes, Size : 130 mm x 65 mm x 27mm , Weight : 160 g, Battery : Two AAA, Warranty : 1 Year BATTERY CHARGING SET (Advanced)The Battery Charger shall meet the following minimum specifications: Charging Type: Constant current charging. Control: Independent current controls provided for all charging circuits. Charging Mode: Automatic reduction of charging current to trickle mode once the battery is fully charged. Indications: LED indication to display fully charged status.Protection Features: Reverse polarity protection, Short circuit protection, Overload protection, Capacity: Capable of charging up to six (6) batteries simultaneously (3 VRLA and 3 Lead Acid batteries).Parameter : Valuee : Number of Batteries : 6, Charging Current : 0.25, 0.5, 0.7, 0.9 A, Constant Charging Current : Yes, Automatic Cut Off : Yes, Dimensions : 39 x 29 x 22 cm, Nett Weight : 11.5 kg Drilling Machine with bitsPower Source : Corded Electric, Maximum Rotational Speed : 2600 RPM, Voltage : 220 Volts, Amperage : 6 Amps, Colour : Multicolour, Included Components : Electric Drill Machine 10mm with Masonry Drill Bit Set, Special Feature : Compact, Material : Plastic, Speed : 2300 RPMAbout this item : ·       Powerful Electric Drill Machine 10mm with Masonry Drill Bit Set ·       220V - 50 Hz - 300W - 2300 RMP - 10 MM ·       rpm: 2300rpm, voltage-220, motor: copper, outer body: pvc and metal ·       Has 5 pieces masonry drill bit set size diameter: 4mm, 5mm, 6mm, 8mm and 10mm material: HSS with brazed carbide tip type: double flute conical tip UV DYE DETECTION KIT - TRACERLINEModel : ‎Complete A/C & Fluid Dye UV Leak Detection Kit, Item Weight : ‎5.4 pounds, Product Dimensions : ‎1 x 1 x 1 inches AC THERMOMETER DIGITALMaximum Resolution : Function: Measurement Range : 0.1µA, Leakage detection 600µA / 6000µA; 0.1mV, DC voltage 600mV; 0.001V, DC voltage 6V / 60V / 600V; 0.1mV, AC voltage 600mV; 0.001V, AC voltage 6V / 60V / 600V; 0.01µA, DC current 600µA / 6000µA; 0.01mA, DC current 60mA / 600mA; 0.001A, DC current 10A; 0.01µA, AC current 600µA / 6000µA; 0.01mA, AC current 60mA / 600mA; 0.001A, AC current 10A; 0.1Ω, Resistance 600Ω / 6kΩ / 60kΩ / 600kΩ / 6MΩ / 60MΩ Sound production below 50Ω; 0.1Ω, On/off detection; On/off detection Display OL above 610Ω; 0.01nF, Capacitance, 6nF / 60nF / 600nF / 6µF; 0.001µF, Capacitance, 60µF / 600µF / 6000µF; 0.001Hz, Frequency : 9.999Hz / 99.9Hz / 999.9Hz / 9.999kHz / 99.99kHz / 999.9kHz/ 9.999MHz; 0.01%, Duty cycle, 0% ~ 100%; 0.001V, Diode, 0V ~ 3.3V; Diode, Display OL above 3.3V MANIFOLD GUAGEType : Analog : Compatible Refrigerant : R-134a, Use : Gas, Display Type : Analog, Pressure Type : Gauge Pressure, Connection Type : NPT, Connection Size : 1/4 inch, Dial Type : Dry, Pressure Range : 0 to 25 bar(0 to 400 psi)Value 4 inch / 100 mm Dulouboe Gauge Manifold AC GAS PURITY ANALYZERPower Supply : 230V AC, Features : Complete Automatics Operation, Usage/Application : Oxygen Gas Purity for various industries, Analysis Time : 1-2 sec, Color : Light Silver, Automation Grade : Automatic, Country of Origin : Made in IndiaFeature : : 1- Cpmplite Automatic Operation. 2-Self Diagnostic check. 3-Proven Sensor Technology. 4- LED Display.Specifications : 1- Range : 0-99.99% with Resolution 0.01%, 2-Display : LED AC Components testing Kit (Universal)The Radiator Pressure Tester and Cooling System Kit shall meet the following minimum specifications: Type & Capacity: 28-piece universal radiator pressure tester and vacuum-type cooling system kit. Functions: Enables testing for leakage in radiator and cooling systems. Allows quick and efficient coolant change.Package Contents: 1 × Hand pressure pump, 2 × Universal radiator adapters, 1 × Adapter spanner, 2 × Vacuum purge & refill kit, 2 × Radiator cap test adapters, 3 × Chromed steel radiator adapters, 17 × Radiator adaptersIdentification: Different color-coded radiator test caps for easy selection and avoidance of confusion. Test Range: 0 – 35 psi, suitable for most types of radiator openings. TOOLS TROLLEY WITH TOOLS & 6 DRAWER TROLLEYUsage/Application : Industrial, Color : Blue, Material : Iron, Type : Cabinet, Usage : Garage Store Tools·           Ergonomic rounded tool box handle.·       Seven Drawers. ·           Three-piece bottom tool box panel. ·           U-channels welded to bottom panel for weight-bearing strength. ·           Three-piece tool box frame construction. ·           Folded side panels for strength. ·           20-gauge tool storage drawers. ·           Ball bearing slides on all tool storage drawers. ·           Rolled edges on all drawers, keeps tool storage drawers rigid. ·           1200 lbs. load capacity casters.Qty : Tray for FOAM Layout : Description : 1 Qty, Tray Foam - 1, Size: 8 mm; 1 Qty, Tray Foam - 1, Size: 10 mm; 1 Qty, Tray Foam - 1, Size: 12mm; 1 Qty, Tray Foam - 1, Size: 14mm; 1 Qty, Tray Foam - 1, Size: 17mm; 12 Qty, Tray Foam - 1, Size 6 x 7 to 30x32 set of 12 pcs; 12 Qty, Tray Foam - 2, Size 6 x 7 to 30x32 set of 12 pcs; 25 Qty, Tray - 5 (In Box - No Foam), Sockets set 1/2 25 pcs; 46 Qty, Tray - 5 (In Box - No Foam), Socket set 1/4 46 pcs; 1 Qty, Tray Foam - 3, Adjustable Wrench AOL: 305 mm; 1 Qty, Tray Foam - 4, Combination Plier 180 mm; 1 Qty, Tray Foam - 4, Water Pump Plier 150 mm; 1 Qty, Tray Foam - 4, Side cutting plier 160 mm; 1 Qty, Tray Foam - 4, Snipe Nose Plier 160 mm; 1 Qty, Tray Foam - 4, Internal - Straight Tip; 1 Qty, Tray Foam - 4, Bent Tip; 1 Qty, Tray Foam - 4, External - Straight Tip; 1 Qty, Tray Foam - 4, Bent Tip; 1 Qty, Tray Foam - 3, Phillips® screwdriver 100 mm Length; 1 Qty, Tray Foam - 3, Phillips® screwdriver 125 mm Length; 1 Qty, Tray Foam - 3, 75 mm Length x 5mm; 1 Qty, Tray Foam - 3, 150 mm Length x 5mm; 1 Qty, Tray Foam - 3, Phillips® screwdriver 25 mm Length; 1 Qty, Tray Foam - 3, Flat screwdriver 25 mm Length; 1 Qty, Tray Foam - 3, Center Punch 125 mm; 1 Qty, Tray Foam - 3, Speed Handle 1/2 Sq. Drive; 1 Qty, Tray Foam - 1, Allen Key Set Contains Sizes 1.5 to 10 mm; 1 Qty, Tray Foam - 3, Drain Plug Remover Square (9.5mm); 1 Qty, Tray Foam - 3, Oil Filter Opening Wrench; 1 Qty, No Foam (Big in Size), Wheel Nut Spanner; 1 Qty, Tools Trolley, Tools Trolley (6 Drawers), Grey Colour; 1 each, Local, Cold Chisel, Scraper, Professional Feeler Gauge Set, Ball Pein Hammer, Rubber Mallet, Plastic Hammer, Tire Lever (600 mm Length) Oil Filter Wrench SetSize/Dimension : 38 x 32 x 101 cm (W x L x H), Usage/Application : Automobile Industry, Socket Type : Hexagonal, Material : Mild Steel, Product Type : Oil Filter Wrench, Drive Size : 1/4 Inch, Type Of Spanner : Cup Filter SpannerProduct Description : full set oil filter wrench for removing oil filters of different vehicles INTELLIGENT - Automotive Circuit TesterType of Product : Automotive Circuit Tester, Color : Greeen, Dimension : 17x15x10 cm, Display Type : TFT True Color Display, Voltage : 12 V, Used For : Wire Check, Resolution : 320x240 DPI, Working Temperature : 0-60°C, Display Size : 6.096 cm, Detect : 9-30 V DIGITAL MULTIMETERModel Name/Number : 106, Warranty : 1 Year, Usage/Application : Digital Multimeter, AC Voltage : 600V, Operating Temperature : +40 Degree celsius, DC Voltage Accuracy : 600V, True RMS/AVG responding : AVG, Display Type : Digital, Weight : 200g, Data Hold : YesMeasures voltage, resistance , continuity , capacitance, Data hold, 6000 count Display (LCD), updates 3/sec, Input terminal for ac and dc current measurements to 10 A and current, IEC 61010-1: 600 V CAT III, Pollution Degree 2, Dimensions: 142 x 69 x 28 mm TORQUE WRENCH 200Nm - 1/2 – DIGITALDrive Size : 1/2 Inch, Warranty : 3 months, Torque Range : 10-200Nm, Overall Length : 300mm, Model Name/Number : WDH200Digital torque wrench 0.3 to 6nm TORQUE WRENCH 40Nm - 3/8 DIGITALDrive Size : 3/8 Inch, Surface Finish : Stainless steel, Torque Range : 1000 - NM, Usage/Application : Industrial, Country of Origin : Made in India Vaccum Cleaners for FloorMaterial : Stainless Steel, Installation Type : Floor stand, Voltage : 220-240 Volt (v), Function : Dry and Wet, Warranty : 1 Year, Number of Motors : 2, Stage : Double, Volt(V) : 220-240, Frequency (Hz) : 50/60, P max (W) : 2600, P (W) : 2300, Water Lift (mm H20) : 2400, Air Flow (m3/h) : 430, Noise Level (dB) : 67, Tank Capacity (Lt) : 76, Weight (Kg) : 24 Windshield glass installermust supply suction cup holders(quantity 2) for windshield holding.Scope of Supply : Supply of Windshield Removal Tool Kit suitable for automotive applications, complete with all standard accessories. 2. Features & Requirements : Designed for easy and flexible insertion of cutting wire through polyurethane adhesive, enabling speedy removal of bonded windshields. Tool construction shall permit placement under the edge of door upholstery panels, with capability to insert into fasteners fully and allow for prying action without damage to panel. Suitable for safe and effective removal of windshield moldings. Capable of cutting through butyl adhesive compounds around windshield periphery. 3.Accessories to be Supplied (Mandatory) : The kit shall include the following tools/accessories: Rubber gasket knife, Cutting wire, Two (02) wire handles, Wire feeder tool, Trim pad remover, Molding release tool 4. Quality & Compliance : Tools shall be manufactured from durable, high-strength material suitable for repeated workshop use. All components must be corrosion resistant and ergonomically designed. Supplier shall confirm compliance with relevant international/Indian standards for hand tools 5.Warranty : Minimum 12 months standard warranty against manufacturing defects. 6. Delivery & Documentation : Complete set to be supplied in suitable carrying/storage case. Operating instructions/manual to be provided along with the kit. Surface TableThe Surface Plate shall meet the following minimum specifications: Material: Made from grey iron casting, conforming to Grade FG-220 as per IS 210. Castings shall be stress-relieved. Top Surface: Precision hand-scraped finish on the working surface. Standards: Manufactured generally in accordance with IS-2285:2003. Calibration: Supplied with a calibration certificate traceable to national standards, compliant with ISO 17025. Protection: Rexine cover provided for the top working surface.Lifting Provisions: Plates up to 630 × 630 mm shall have mild steel handles for lifting. Larger plates shall include cored holes at the periphery for lifting. Optional Features: Upon request, the plate may include grid lines for location, tapped holes, or T-slots.Specification : Details : Size : 630 x 630 x 100 mm, Material : Cast Iron, Flatness : 5 Micron Magnetic V BlockSize : 4 inch, Weight : Depending on the size, weight can vary from 1 kg to 5 kg, providing stability during machining opera, Material : Typically made from hardened steel or cast iron for durability and stability. V-Groove Angle : The angle of the V groove is typically 90 degrees, allowing for stable support of cylindrical object, Country of Origin : Made in Indiasizes : 4.6.8 . Features: ·       Precise design Sturdy construction Low maintenance Hand Drilling MachineType of Product : Impact Drill, No Load Speed : 3250 RPM, Rated Torque : 2.1 Nm, Concrete Drilling Diameter : 16 mm, Drilling Dia. In Masonry : 18 mm, Steel Drilling Diameter : 12 mm, Drill Spindle Connecting Thread : 1/2-20 UNF, Frequency : 50 Hz, Voltage : 220-240 V, Weight : 1.8 Kg, Wood Drilling Diameter : 25 mm, Chuck Capacity : 1.5 - 13 mm, Chuck Size : 16 mm, Power : 750 W, Impact Rate : 48500 bpm, Output Power : 351 W, Size : 13 MM, Package Contains : 1 x GSB 16 RE, 1 x Auxiliary handle, 1 x Chuck key, 1 x Depth gauge, Dimension (LXWXH) cm : ‎30L x 26W x 9H cm, Country of Origin : India, Power Range : 501 - 800 W Valve GRINDING MachineDisc Diameter : 4 inch, No Load Speed : 11000 RPM, Voltage : 230V, Is It Spindle Lock : Spindle Lock, Warranty : 6 months, Item Weight (Kgs) : 1.8 kg, Power : 670 Watt Bench vice HeavyType of Product : Bench Vice, Size : 150 mm, Weight :13.5 kg, Color : Assorted, Material : Cast Iron, Product Sub Type : Heavy Duty, Country of Origin : India Bench Grinding Machine1.     The Bench Grinder shall meet the following minimum requirements: 2. Motor Power: 350 W induction motor suitable for heavy-duty grinding operations. 3. Weight: Approximately 10 kg. 4. Housing: Die-cast aluminium construction with ball bearings to protect the motor from dust and debris and ensure smooth operation. 5. Stability: Sturdy and stable base to maintain firm placement during operation. 6. Grinding Wheels:Diameter: 150 mm, Width: 20 mm, Bore: 20 mm, No-load speed: 3,000 rpm, 7. Scope of Supply: Adjustable workpiece supports, Steel protective guards, Spark protective covers, Grinding wheels (normal grit 24 and 60), 8. Applications: Suitable for grinding, sharpening, and smoothing tough materials in workshop or industrial settings.Specification : Details : Material : Metal, Plastic, Product Dimensions : 19.5L x 15W x 21.5H cm, Style : Modern, Power Source : Corded Electric, Colour : Blue, Item Weight : 4.2 kg, Voltage : 240 V, Wattage : 350 W, Maximum Rotational Speed : 3000 RPM, Horsepower : 0.46 HP Height GuageMeasuring Range : 600 mm, Type : Double Column, Accuracy : 0.01 mm, Usage/Application : Height MeasurementsThe Height Measuring Gauge is an advanced standing digital co-coordinate measuring machine that integrates precision machinery, modern sensor technology, and electronic innovation. This versatile tool is essential across various industries, including precision machinery, hardware, and plastics. Digital VernierBattery : SR44 (1 pc), 938882, Resolution : 0.01mm or .0005 / 0.01mm, Display : LCD, Scale type : Absolute Electromagnetic Linear Encoder, Max response speed : Unlimited, Battery life : Approx. 5,000 Hours in Continuous Use, Dust Water protection level : IP66, Standard accessory : Jaw Clamps (2 pcs), 05GZA033Functions:·       Origin-set, Zero-setting, Presetting, Offsetting, Data hold, ·       Automatic power on/off, ·       Data output, inch/mm conversion (inch/mm models), ·       Alarm: Low voltage, counting value composition error Dies and Taps set (Inches & MM)Material : Stainleess Steeel, Color : Silver, Material : Stainleess Steeel, Finishing : Polished, Shape : Round TWO BEARING SEPERATOR SETBearing Separator : 9000 & 9005, H-Type Beam : Included, Bolts : Included, Carrying Case : Included, Material : Steel, Product Type : Hand Tool Kit, Color : Red, Features : Bearing Removal, H-Type Beam, Bolts Included, Durable Kit, Versatile Use BENCH WISE - 8Type of Product : Bench Vice, Size : 150 mm, Weight : 13.5 kg, Color : Assorted BENCH GRINDER - 6No Load Speed : 2950 RPM, Wheel Diameter : 200 mm, Type of Product : Bench Grinder, Application : Grinding, Voltage : 220-240 V, Frequency : 50 Hz, Power : 350 W, Color : Yellow, Material : Alloy Steel, Rated Input Power : 350W, Wheel Size : 200×20×16 mm, Package Contains : 1 x Bench Grinder, 1set eye shields, 1pcs tool storage box, 1pcs work light, Power Range : 201-400 W, Base Material : Aluminum, Warranty Duration : 12 Months HD COIL SPRING COMPRESSORHook Jaw Externsion : 11 Inches, Safegaurd Extension : 12 Inches, Material : Mild Steel, Country of Origin : Made in India, Mode of Operation : Hydraulic foot operated TROLLY 200KGSUsage/Application : Warehouse, Material : Mild Steel, Structure : Platform, Load Capacity : 200 kg, Size/Dimension : 600 x 300 mm, No Of Wheels : 4, Finish : High Gloss, Shape : Rectangular, Surface Treatment : Galvanized VIDEO SCOPEWeight : 2 kg, Resolution : Video Recording Resolution: 1920x1080, 1280x720 (MOV), Color : Black & Orange, Screen : Screen: 5 inch IPS HD Display, Battery Backup : no, Operating Temperature: 32 Degree to 113 DegreeF (0 Degree to 45 DegreeC), Power : Power Source: 2600mAh lithium battery, Video Boroscope 3Mtr x 3.9mm Dia Masking Paper Stand SAR173Material : Steel, Color : Red, Weight : 10kg, Dimensions : 100x50x75cm, Roll Capacity : 3 Rolls, Wheel Type : Caster, Usage : Supports and dispenses masking paper rolls for painting or industrial applications. Features : Easy Roll, Stable Base, Convenient Use, Efficient Storage, Space Saving, Durable Design Auto Panel StandPower Source : Electric, Generator, Material : Mild Steel, Power : 3HP- 50HP, Phase : Three Phase, Supply Voltage : 440 V Masking Film Stand Film Width : 450 mm, Capacity : 10 piece/min, Type : Semi Automatic, Usage : pouch making application, Application : pouch making, Weight : 800 g, Country of Origin : Made in India Masking Paper Stand SARTS Scope of Supply : Supply of Paper Tape Dispenser Stand Tool suitable for masking operations in automobile body repair workshops, complete with all required accessories.2. Features & Requirements : Specially designed dispenser stand for cutting masking paper, ensuring quick and easy masking during auto body repair work. Suitable for use with masking paper rolls up to 23 inches width. Overall size of stand: 19 × 26 × 28 inches (48 × 68 × 72 cm). Construction material: Iron (high strength and durable). Both ends provided with fixing screws to allow easy adjustment of paper loading position. Integrated cutters with spring mechanism at both ends for holding and cutting the masking paper efficiently. Equipped with tape mounting wheel (red wheel) for installation of masking tape rolls. The tape can be dispensed along with masking paper, with adjustable screw positions for precise tape alignment. Provided with a large bottom storage tray for holding tools/materials. Fitted with wheels at the bottom for easy mobility; smooth steering and flexible movement ensured. Cutting blades must be user-friendly, durable, and safe in operation. 3. Quality & Compliance : Frame must be made of powder-coated/corrosion-resistant iron for durability. All moving parts shall be smooth in operation and free from burrs or sharp edges. Supplier must confirm compliance with applicable Indian/International standards for workshop equipment.4. Warranty : Minimum 12 months warranty against manufacturing defects.5. Delivery & Documentation : Equipment to be supplied as a complete assembly, ready for use. MASKING PAPER (40 GSM) WHITE 450MM×200M should supply in the form of roll. 5 meter long minimum MASKING FILM 4M*300M 8 MICRON HDPE should supply in the form of roll. 5 meter long minimum White Masking Paper (40gsm) 900mm X 200mm should supply in the form of roll. 5 meter long minimum MASKING TAPE AUTOMOTIVE GRADE YELLOW 80°C 24MM×50MType of Product : Masking Tape, Length : 50 m, Thickness : 0.17 mm, Color : White or yellow PRE-TAPED KRAFT PAPER 100MM×20M Tape Width : 100 mm, Tape Length : 20 Meter, Roll length :25 m, Overall Thickness (Imperial) : 150mm, sizes : 6inch in width and 20mtr in length. AOFEI - RESPIRATOR Type of Product : Half Facepiece Reusable Respirator, Color : Grey, Size : medium, Material : Thermoplastic Elastomer (TPE), Application : Construction, Food & Beverage Manufacturing, General Manufacturing, Heavy Industrial, Manufacturing, Marine, Mining, Oil & Gas, Pharmaceutical, Transportation, Country of Origin : India, Harness Type : 4 Point, Mask Type : Reeusablee, Design : Half Facee, Connection Type : Bayoneet, Features : Dual Airline Supplied Air Compatible, Pack of : 1 Pcs MACHANICAL WEAR SUITModel : Boiler Suit for Men, Workwear Uniform, Multiple Pockets, Size : As per required, Color : Blue, Fabric : 55% Modacrylic, 43% Cotton, 2% AS, ClosureType : Zippeer, Number of Pockets : 8, Hood Attached : No, Boots Attached : No,Ideal For : Men, Reusable : Yes, Key Features : Flame-Resistant (IFR) Fabric Blend – 55% Modacrylic, 43% Cotton & 2% AS for certified fire protection and anti-static properties. Other Features : Reflective Tape for 360° Visibility – Strategically placed for high visibility in low-light and hazardous work conditions.Dimensions : Inside Leg Length ·       165.1 cm, Waist : ·       106.68 cm, Chest : ·       127 cm, Length : ·       165.1 cm SAEFTY SHOESSole : PU, Size : As required, Style : High Ankle, Toe Cap : Steel Toe, Upper : Leatheerr, Oil Resistant : Yes, Chemical Resistant : Yes, Color : Black, Type of Product : Safety Shoes, Model : Excavator, Upper Material : Full Grain Leather, Ankle Type : High Ankle, Suitable For : Engineering,Petrochemical & Construction, Toe Type :Steel Toe, Anti Skid : Yes, Country of Origin : India Balancer WeightsSL. .No : Description of Goods : 05GM : 100 NO, 10GM : 100 NO, 15GM : 100 NO, 20GM : 100 NO, 25GM : 100 NO : 100 NO, 30GM : 100 NO : 100 NO, 35GM : 100 NO : 100 NO, 40GM : 50, 45GM : 50 NNO, 50GM : 50 NNO, Sticker Weights: 100 NO, 414 Steels Valves : 100 NO, Sarv Kit : 1 NO, Kwik Repair Seals : 2 BOX, Green Caps : 1 PKT, Ventifix: 2NO, Valve Dies : 2NO AIR COMPRESSOR PIPING 800 METER INCLUDING ALL FIXTURESAir pipe line material along with installation over the walls from the point of Air compressor to various machines such as impact wrench,air filler,nitrogen generator,dusting guns,washing bays,Tyre changer, automatic car washer, etc along with all the necessary fittings suitable for the tools and machines that are supplied by the vendor( I.e mentioned in the tender) The following must include in the same:Easy coupllers for impact wrench Easy coupllers for Dusting guns Ball walls for air compressors out put and input line.HDPE 1 inch pipe must be usedAll the fitting like :tea joint, coupling,end cap,flange adopters,elbows,stop valve etc must be used as per ISI/ISO standard. As per the layout of the work place and positioning of the machines air pipe line must be completed. Pneumatic tubes 10mm, 8mm,12mm each of 10 meters ( used for connecting impact wrench, Dusting guns, air jacks) must be supplied as per the quantity of the machines. Wall mounting materials,nails, clamps,solvents, jointing guns,glue guns, loading, unloading,labour force, any additional material or service that are required for the installation of pipe line are to be taken care by the vendor. A minimum warranty of 2 years must be provided. 2 air input access points with 1 inch ball valve each must be provided for every two post lift,Four post lift,nitro truck,Nitrogen generator,Tyre changers,washing lifts,automatic car washer. OIL PIPING 400 METER INCLUDES *FOR 24Lift * 2 oil LineOil piping line is used to collect the waste oil from various vehicles at the working bays ( 26 bays). 1 input access point must be provided at every servicing bay. (26) 2 central collection center along with 500ltr iron drum ( to collect all the waste oil in a drum) should be provided, Must use cold and HOT temperature resistive pipes for pipe line. ISI/ISO standards only, 1 Ball valve along with 2 ltr funnel and 3 meters extended flexible temperature resistive pipe/tube to be provided at every access point. All the fittings,joints,valves must be ISI standard. Wall mounting materials,nails, clamps,solvents, jointing guns,glue guns, loading, unloading,labour force, any additional material or service that are required for the installation of pipe line are to be taken care by the vendor. Pipes that are usde fpr oil pipe line must be 1.5 inch in diameter