BRR : 6213074 Bids Are Invited For Monthly Basis Cab & Taxi Hiring Services - Suv; 2000 Km X 320 Hours; Local , Monthly Basis Cab & Taxi Hiring Services - Suv; 2500 Km X 320 Hours; Localvehicles To Any Centralstate Govt. Organizationpsu Against One Contra Ct. The Bidder Should Have Satisfactory Performance. The Period, Number Of Veh Icles & Performance Should Be Clearly Mentioned In The Experience Certicate Fa Iling Which His Experience Shall Be Treated As Nil And The Bid Shall Be Liable To B E Rejected. The Existing Vendors Providing Vehicles On Hiring Basis To B Snl Need Not Required To Submit Experience Certicate, However Bidde R Has To Submit A Self Declaration In This Regard. 4. Average Annual Nancial Turnover During The Last Three Years, Ending 31St Ma Rch Of The Previous Nancial Year I.E. 31-03-2023 ( I.E. Nancial Year 2020-21, F Y 2021-22, Fy 2022-23 ) , Should Be At Least 30% Of The Cost. Audited Balance Sheets For The Last Three Years Shall Be Submitted As A Supporting Docu Ment. If Certified Copy By Ca For 2022-23 Is Not Available Then Certified Documen Ts For 2019-20 Will Be Considered. 5. Solvency Certificate From The Banker Of Tenderer : - For The Work Costing Up To Rs 20 Lacs-Rs 2 Lacs ; For The Work Costing More Than 20 Lacs But Below 5 0 Lacs- Rs 5 Lacs & For The Work Costing More Than 50 Lacs- Rs 10 Lacs. The Date Of Issue Of Solvency Certicate Shall Not Be Older Than Six Months From The Date Of Issue Of Nit. ( Format As Per Annexure-Ii ) 6. Near Relationship Certificate: A ) The Bidder Should Give A Certicate That None Of His Her Near Relative, As Dened Below, Is Working In The Units Where He Is Going To Apply For The Tender. In Case Of Proprietorship Firm Certificate Will Be Given By The Proprietor. For Partnership Rm Certicate Will Be Given By All The Partn Ers And In Case Of Limited Company By All The Directors Of The Company Excluding Government Of India Financial Institution Nominees And Inde Pendent Non-Ocial Part Time Directors Appointed By Govt. Of India Or The Governor Of The State And Full Time Directors Of Psus Both State And Central. Due To Any Breach Of These Conditions By The Company Or Rm Or Any Other Person The Tender Will Be Cancelled And Bid Security Will B E Forfeited At Any Stage Whenever It Is Noticed And Bsnl Will Not Pay An Y Damage To The Company Or Firm Or The Concerned Person. B ) The Near Relatives For This Purpose Are Defined As:- 7 18 ( A ) Members Of A Hindu Undivided Family. ( B ) They Are Husband And Wife. ( C ) The One Is Related To The Other In The Manner As Father, Mother, Son ( S ) & Sons Wife ( Daughter In Law ) , Daughter ( S ) And Daughters Hu Sband ( Son In Law ) , Brother ( S ) And Brothers Wife, Sister ( S ) And Sisters Husband ( Brother In Law ) . C ) The Bidder Should Submit Near Relationship Certicate In The Specified Format ( Annexure-Iii ) . 7. The Bidder Should Submit Bid Security Declaration In The Specied Format ( An Nexure-Iv ) . 8. No Revision Of Price Will Be Permissible On Account Of Revision Of Prices For Any Inputs, Cost Of Repair Or Maintenance Charges Or Drivers Salary Etc. However Pric E Variation Is Admissible For Fuel As Per Clause 14 Price Variation. 9. Rate Of Monthly Hire Charges For Normal Run Of 2000 2500 Km In A Month ( 32 0 Hrs Per Month ) On All Days Of Month ( Expect Sunday ) For Each Car. The Normal Run Will Include Distance Covered Even On Over Time. The Normal Run Will Include Distance Covered Even On Over Time. Pl. See Clause 4 Of Service Providers Obligations. 10. The Unused Kms If Any During A Particular Month Will Be Carried Over To The Su Bsequent Two Month And Extra Kms If Any Travelled During These Two Months Wil L Be Adjusted Against These Unused Kms For Individual Vehicle. Payment Will Be Made Of Balance Remaining Extra Km After Adjustment Of Extra Km In Two Month S For Individual Vehicle. 11. Right To Vary Quantities Bsnl Reserves The Right At The Time Of Award Of Contract To Increase Or Dec Rease Upto 25% Of The Tendered Quantity Of Services Without Any Change I N Hiring Charges Of The Oered Quantity Or Other Terms And Conditions. Ho Wever Bsnl Shall Place Order As Per The Actual Requirement Only. 12. Terms Of Payment: The Payment Shall Be Made On Submission Of Monthly Bills I.R.O Vehicles Hired To Authority Nominat Ed By Pgmtd, Bsnl Submitted Along With Following Documents:- A ) Duly Receipted Billinvoice In Duplicate B ) Copy Of Hire Order ( By Vehicle In-Charge ) C ) Photo Copy Of Duty Sliplog Book Duly Signed By Driver And Vehicle User. ( By Vehicle In-Charge ) D ) Copy Of Challan As A Proof Of Paying Gst As Per Standing Instruction ( By Contractor ) . E ) Due Certicates On Bills By Vehicle User Concerned. In Case, The Bills Are Not Submitted To Vehi 8 18Cle In-Charge Along With Above Documents Latest By 10Th Of Month End, Bsnl Will Not Be Respo Nsible For Delay In Payment. F ) The Bills Should Be Sent To Bsnl For Payment Vehicle-Wise. It Should Be Ensured That There Is No Overwriting In The Duty Slipslog Book. In No Case, Duty Sliplog Book Without Signature Will Be Accepted For Payment And If It Is Found So, The Amount Will Be Disallowed. G ) In Case The Vehicle Engaged On Monthly Basis Is To Be Discontinued During The Month, The Bill I S Paid On Actual Basis, As Per Terms & Conditions. H ) The Bills Will Be Paid After Deducting Tds As Per Standing Instructions Of Income Tax Authorities From Paymentbill And It Can Be Timely Changed According To Concerned Department Guidelines. I ) Contractor Will Make Due Payment To All The Vehicle Owner His Employees Engaged For Execu Tion Of Work Specified In The Tender, As Per Laws Every Month Insulating It From Payments From B Snl. Delay In Bill Payment Will Not Be A Excuse For Not Providing A Vehicle. J ) Bill Process & Payment Will Be Done By The Concerned Ao Of Jaipur Ba. K ) If Applicable Then Copy Of Epfesi Challan As Per Standing Instructions Of Epfesi Authority ( By Contractor ) Or Certificate That Vehicle Is Driven By The Owner Himself. 13. Gst Invoice And Compliances ( If Applicable ) A. All The Details Of The Vendor ( Name, Address, Gstninunregistered V Endor ) , Sachsn Code Etc., ) And Other Mandatory Details Shall Be Me Ntioned On The Invoice. B. Invoicesupplementary Invoice Supplementary Invoicedebit Not Ecredit Notereceipt Voucher Need To Be Issued In Compliant Format And Timely Within The Time Prescribed Under Gst Law. C. It Would Be The Responsibility Of The Vendor To Declare Correct Infor Mation On Invoice And Gstn Viz. The Amount, Rate Of Tax Etc. In Case, The Eligibility Of Input Tax Credit Is Questioned Or Denied To Bsnl On Ac Count Of Default By The Vendor, The Same Would Be Recovered By Bsn L From The Supplier. D. A Self-Declaration Along With Evidence That The Bidder Is Not Blacklist Ed By Gst Authorities. In Case Vendor Gets Black Listed During The Ten Ure Of Bsnl Contract, Then Vendor Must Indemnify Bsnl To Ensure Th At No Loss Of Input Tax Credit Is Borne By Bsnl Due To Default Of Vendor . E. If Vendor Concerned Does Not Deposit The Gst As Per Rules On Timely Basis, Then As Per Corporate Guidelines, Sap System Will Automatically Retain The Gst Amount Which Will Be 2 Times Of T He Gst Amount Charged In The Invoice. 14. Price Variation A. Hire Charges Due To Change In Fuel Price Will Be Reviewed Qu Arterly. B. The Review For Change In Hire Charges Due To Change In Fuel Rates Sha Ll Be Aected At The End Of Quarter, Irrespective Of Start Of Contract I.E. On 31St March, 30Th June, 30 Sept, And 31St December. The Change In Hire Charges, If Any, Shall Be Applicable From The Ist Day Of Next Quarte R. Base Rate Of Fuel Would Be Fuel Prices As On Date Of Award Of Contrac T. However, Decision Of Bsnl Whether To Enhance Fuel Price Or 9 18Not Is Final. Revised Fuel Rate Would Be The Fuel Prices On First Day Of The Quarter. Increase Or Decrease In The Hire Charges Due To These Variations Shall Be Worked Out From The Base Rate On The Following Formula: - Monthly Km Hire Slab ( I.E 20002500 Kms ) X ( Revised Rate Per Litre - Base Rate Per Litre ) Averag E Km Per Litre Of Diesel Petrol Consumption ( Kmpl ) ( Note:- The Base Rate Of Petroldiesel Is The Prevailing Rate On The Date Of Commencement Of Work Contract. The Average Kmpl Is To Be Assumed As 18 Km Per Liter In Case Of Type I V Ehicle ( Sedan ) And 12 Km Per Liter In Case Of Type Ii ( Suv ) . If There Is Decrease In Fuel Price, Formula Will Indicate Negative Gure Which Means The Deduction Shall Be Done From The Bill ) C. The Service Provider Shall Submit Supplementary Bill For Reimbursem Ent Towards Increase In Fuel Price On Monthly Basis Without Accumulat Ion. This Supplementary Bill Is To Be Supported With Proof Of Fuel Price St Prevailing On 1 Of The Month. 15. Termination Of Contract L ) In Case Of Any Default By The Service Provider And In Any Of The Terms & Conditions ( Whether General Or Special ) , Bsnl May Without Prejudic E To Any Other Rightremedy Which Shall Have Accrued Or Shall Accrue T Hereafter, Terminate The Contract, In Whole Or In Part, By Giving 2 Clear Working Days Notice In Writing To The Service Provider. M ) All Instructions, Notices And Communications Etc. Under The Contract Given In Writing And If Sent To The Last Known Place Of Business, Shall B E Deemed To Be Served On The Date, Even In Ordinary Course Of Post, T Hese Would Have Been Delivered To The Service Provider. N ) Notwithstanding Anything Contained Herein, Bsnl Also Reserves The Ri Ght To Terminate The Contract At Any Time Or Stage During The Period Of Contract, By Giving Two Days Notice In Writing Without Assigning Any Re Ason And Without Incurring Any Nancial Liability Whatsoever To The Ser Vice Provider. 16. Termination For Insolvency: Bsnl May Also By Giving Written Notice And Without Compensation To The Service Provider Terminate The Contract If The Service Provider Bec Omes Unwilling, Bankrupt Or Otherwise Insolvent Without Aecting Its Ri Ght Of Action Or Remedy As Hirer. 17. Insurance : The Insurance Cover Protecting The Agency Against All Claims Applicabl E Under The Workmens Compensation Act, 1948 Or As Per Any Act In In Dia From Time To Time Shall Be Taken By The Service Provider. The Servi Ce Provider Shall Arrange Necessary Insurance Cover For Any Persons D Eployed By Him Even For Short Duration. Bsnl Shall Not Entertain Any Cl Aim Arising Out Of Mishap, If Any, That May Take Place. In The Event Of 10 18Any Liabilityclaim Falling On Bsnl, The Same Shall Be Reimbursed Inde Mnified By The Service Provider. 18. Prices: O ) The Rates Should Be On Monthly Basis. The Rate Extra Per Km Running And Extra Duty Hrs Are To Be Indicated. P ) Rates Charged By The Service Provider For The Services Given Under Th E Contract Shall Not Be Higher Than The Rates Quoted By The Service Pr Ovider In His Bid. Q ) In Case Of Any Reduction Of Taxes And Statutory Levies ( If Any ) During T He Contractual Period, Bsnl Shall Take The Benet Of Decrease In Such Taxes Duties For The Services To Be Availed From The Date Of Enact Ment Of Revised Duties Taxes. R ) In Case Of Increase In Taxes Duties During The Contractual Period, Bs Nl Shall Be Liable To Revise The Rates As Per New Taxes Duties For The S Ervices To Be Availed For The Remaining Period Of The Contract. 19. Contractor Is Required To Get Signed The Duty Slips In Prescribed Format At Ann Exure-V By The User For Need Basis Vehicles. Contractor Is Required To Get Signe D Daily On Summary Sheet By The User And At The End Of The Month Nally Get Ve Rify The Summary Sheet By The User In Prescribed Format At Annexure-Vi. 20. Bid- Evaluation:- During The Evaluation Process, The Documents May Be Classified In Two Categories :- A ) Essential Documents: - Experience Certificate, Solvency Certificate, Emdbid Security Or Mse Bodies Udyam Certificate In Case Of Exemption From Emd Which Makes The Bid Valid. B ) Other Documents: - All Other Document Like Epf, Esi, Pan Card Etc Except Ess Ential Documents. Copy Of Rc Has To Be Submitted To Identify The Model Of The Vehicle. Tec Reserve Right To Collect Documents Other Then Essential Documents Directly From The Bidder Within Time Frame And Submit Conclusive Repor T To Tendering Authority. In Absence Of Essential Documents Bid Sh All Be Treated As Invalid 21. Calculation Formula For The Service $Total = $Quantity*$Cost*$Duration_In_Months $Quantity = Number Of Vehicle ( S ) $Cost = Monthly Base Fare ( Per Package ) Inclusive Of Gst $Duration_In_Months = Duration In Months 11 18 22. The Format Of The Performance Security Bond Is Attached As Per Anne Xure-Vii. 23. Estimate Value ( Tender Cost ) Calculation As Under:- S.N Vehicle Ty Monthly Package No Of Estimate Annual Es Extra Km Extra Ho O Pe As Per Gem Vehicl D Monthl Timated C Charges Ur Charg Es Y Charge Harges In In Rs. ( E Es In Rs. S In Rs ( E Rs ( Exclu Xcluding ( Excludin Xcluding Ding Gst ) Gst ) G Gst ) Gst ) Type-Ii ( Su 1 V ) 2000 Km X 320Hrs. 11 37100 4897200 12 30 Type-Ii ( Su 2 V ) 2500 Km X 320Hrs. 2 43100 1034400 12 30 13 5931600 Scope Of Work The Bidder Is Required To Provide Commercial Vehicles Fully Conforming To Rtar To Regulation Along With Fuel, Driver Etc And Carryout Periodical Maintenance An D Execute The Work Through Their Supervisor. The Work Consists Of One Part On Monthly Slab Rate. Period Of Contract: Under Normal Circumstances The Contract Shall Be Valid For A Period Of One Yea R From The Date Of Agreement. However Contract May Be Extended On The Sam E Rate, Terms & Conditions Unilaterally By Bsnl For A Further Period Of Six Months At A Time And Upto A Maximum Of One Year, As May Be Decided By Th E Competent Authority, After Review Of Performance. Scheduled Works Monthly Km Hire Slab: As Per Monthly Requirement The Vehicles Will Be Requisitioned. The Monthly Km Hire Slab On Which Vehicles Are Required And The Number Of Such Hiring Per Month Are Tentatively Indicated Below. 12 18 Area Of Operation Monthly Hire Slab Quantity Of Hired V Ehicle ( Suv Type ) - ( Petrol Diesel Cng ) - Type-Ii # 2000 Kms And 320 Hrs Per Mo 11 Jaipur Ba Nth # 2500 Kms And 320 Hrs Per Mo 02 Jaipur Ba Nth 13 # Jaipur Ba: Jaipur Oa ( Includes Revenue District Dausa & Jaipur ) , Sawai Madhopur Oa ( Includes Revenue District Karauli & Sawai Madhopur ) And Tonk Oa Including T Onk Revenue District. # Note: The Tables Shown In Schedule Of Work Above Are Only Indicative And For Re Gular Work. The Actual Deployment May Vary From Time To Time Depending On Work Schedule, Companys Policy, Intensity Of Maintenance And Interruption Duties And D Evelopmental Activities Etc. However, The Area Of Operation Of Vehicles Is Jai Pur Ba Only But Depending On The Requirements Of Emergent Nature The S Ame Can Be Taken As Rajasthan Circle. Annexure-I Statement Of Vehicles Owned On Lease By The Bidder Bidders Name: Companys Name: Details Of Ownedon Lease Vehicles As Mentioned In Nit As On Date: 320 Hours; Local , Monthly Basis Cab & Taxi Hiring Services - Suv; 2500 Km X 320 Hours; Local Total Quantity :

BRR : 6249097 Bids Are Invited For Fmonthly Basis Cab & Taxi Hiring Services - Sedan; 1500 Km X 320 Hours; Localto Submit Experience Certificate, However Bidd Er Has To Submit A Self Declaration In This Regard. 4. Average Annual Nancial Turnover During The Last Three Years, Ending 31St Ma Rch Of The Previous Nancial Year I.E. 31-03-2023 ( I.E. Nancial Year 2020-21, F Y 2021-22, Fy 2022-23 ) , Should Be At Least 30% Of The Cost. Audited Balance Sheets For The Last Three Years Shall Be Submitted As A Supporting Docu Ment. If Certified Copy By Ca For 2022-23 Is Not Available Then Certified Documen Ts For 2019-20 Will Be Considered. 5. Solvency Certificate From The Banker Of Tenderer : - For The Work Costing Up To Rs 20 Lacs-Rs 2 Lacs ; For The Work Costing More Than 20 Lacs But Below 5 0 Lacs- Rs 5 Lacs & For The Work Costing More Than 50 Lacs- Rs 10 Lacs. The Date Of Issue Of Solvency Certicate Shall Not Be Older Than Six Months From The Date Of Issue Of Nit. ( Format As Per Annexure-Ii ) 6. Near Relationship Certificate: A ) The Bidder Should Give A Certificate That None Of His Her Near Relative, As Dened Below, Is Working In The Units Where He Is Going To Apply For The Tender. In Case Of Proprietorship Firm Certificate Will Be Given By The Proprietor. For Partnership Rm Certicate Will Be Given By All The Partn Ers And In Case Of Limited Company By All The Directors Of The Company Excluding Government Of India Financial Institution Nominees And Inde Pendent Non-Ocial Part Time Directors Appointed By Govt. Of India Or The Governor Of The State And Full Time Directors Of Psus Both State An D Central. Due To Any Breach Of These Conditions By The Company Or R M Or Any Other Person The Tender Will Be Cancelled And Bid Security Will Be Forfeited At Any Stage Whenever It Is Noticed And Bsnl Will Not Pay 6 17Any Damage To The Company Or Firm Or The Concerned Person. B ) The Near Relatives For This Purpose Are Defined As:- ( A ) Members Of A Hindu Undivided Family. ( B ) They Are Husband And Wife. ( C ) The One Is Related To The Other In The Manner As Father, Mother, Son ( S ) & Sons Wife ( Daughter In Law ) , Daughter ( S ) And Daughters Hu Sband ( Son In Law ) , Brother ( S ) And Brothers Wife, Sister ( S ) And Sister S Husband ( Brother In Law ) . C ) The Bidder Should Submit Near Relationship Certicate In The Specie D Format ( Annexure-Iii ) . 7. The Bidder Should Submit Bid Security Declaration In The Specied Format ( An Nexure-Iv ) . 8. No Revision Of Price Will Be Permissible On Account Of Revision Of Prices For Any Inputs, Cost Of Repair Or Maintenance Charges Or Drivers Salary Etc. However Pric E Variation Is Admissible For Fuel As Per Clause 14 Price Variation. 9. Rate Of Monthly Hire Charges For Normal Run Of 1500 Km In A Month ( 320 Hrs Per Month ) On All Days Of Month ( Expect Sunday ) For Each Car. The Normal Run Will Include Distance Covered Even On Over Time. The Normal Run Will Include Dist Ance Covered Even On Over Time. Pl. See Clause 4 Of Service Providers O Bligations. 10. The Unused Kms If Any During A Particular Month Will Be Carried Over To The Su Bsequent Two Month And Extra Kms If Any Travelled During These Two Months Wil L Be Adjusted Against These Unused Kms For Individual Vehicle. Payment Will Be Made Of Balance Remaining Extra Km After Adjustment Of Extra Km In Two Month S For Individual Vehicle. 11. Right To Vary Quantities Bsnl Reserves The Right At The Time Of Award Of Contract To Increase Or De Crease Upto 25% Of The Tendered Quantity Of Services Without Any Change In Hiring Charges Of The Oered Quantity Or Other Terms And Conditions. Ho Wever Bsnl Shall Place Order As Per The Actual Requirement Only. 12. Terms Of Payment: The Payment Shall Be Made On Submission Of Monthly Bills I.R.O Vehicles Hired To Authority Nominat Ed By Pgmtd, Bsnl Submitted Along With Following Documents:- A ) Duly Receipted Billinvoice In Duplicate B ) Copy Of Hire Order ( By Vehicle In-Charge ) 7 17C ) Photo Copy Of Duty Sliplog Book Duly Signed By Driver And Vehicle User. ( By Vehicle In-Charge ) D ) Copy Of Challan As A Proof Of Paying Gst As Per Standing Instruction ( By Contractor ) . E ) Due Certicates On Bills By Vehicle User Concerned. In Case, The Bills Are Not Submitted To Vehi Cle In-Charge Along With Above Documents Latest By 10Th Of Month End, Bsnl Will Not Be Respo Nsible For Delay In Payment. F ) The Bills Should Be Sent To Bsnl For Payment Vehicle-Wise. It Should Be Ensured That There Is No Overwriting In The Duty Slipslog Book. In No Case, Duty Sliplog Book Without Signature Will Be Accepted For Payment And If It Is Found So, The Amount Will Be Disallowed. G ) In Case The Vehicle Engaged On Monthly Basis Is To Be Discontinued During The Month, The Bill I S Paid On Actual Basis, As Per Terms & Conditions. H ) The Bills Will Be Paid After Deducting Tds As Per Standing Instructions Of Income Tax Authoritie S From Paymentbill And It Can Be Timely Changed According To Concerned Department Guideline S. I ) Contractor Will Make Due Payment To All The Vehicle Owner His Employees Engaged For Execu Tion Of Work Specied In The Tender, As Per Laws Every Month Insulating It From Payments From Bsnl. Delay In Bill Payment Will Not Be A Excuse For Not Providing A Vehicle. J ) Bill Process & Payment Will Be Done By The Concerned Ao Of Jaipur Ba. K ) If Applicable Then Copy Of Epfesi Challan As Per Standing Instructions Of Epfesi Authority ( By Contractor ) Or Certificate That Vehicle Is Driven By The Owner Himself. 13. Gst Invoice And Compliances ( If Applicable ) A. All The Details Of The Vendor ( Name, Address, Gstninunregistered Vendor ) , Sachsn Code Etc., ) And Other Mandatory Details Shall Be M Entioned On The Invoice. B. Invoicesupplementary Invoice Supplementary Invoicedebit Not Ecredit Notereceipt Voucher Need To Be Issued In Compliant Format And Timely Within The Time Prescribed Under Gst Law. C. It Would Be The Responsibility Of The Vendor To Declare Correct Infor Mation On Invoice And Gstn Viz. The Amount, Rate Of Tax Etc. In Case, The Eligibility Of Input Tax Credit Is Questioned Or Denied To Bsnl On A Ccount Of Default By The Vendor, The Same Would Be Recovered By Bs Nl From The Supplier. D. A Self-Declaration Along With Evidence That The Bidder Is Not Blacklist Ed By Gst Authorities. In Case Vendor Gets Black Listed During The Ten Ure Of Bsnl Contract, Then Vendor Must Indemnify Bsnl To Ensure Th At No Loss Of Input Tax Credit Is Borne By Bsnl Due To Default Of Vendo R. E. If Vendor Concerned Does Not Deposit The Gst As Per Rules On Timely Basis, Then As Per Corporate Guidelines, Sap System Will Automatically Retain The Gst Amount Which Will Be 2 Times Of T He Gst Amount Charged In The Invoice. 14. Price Variation A. Hire Charges Due To Change In Fuel Price Will Be Reviewed Qu Arterly. B. The Review For Change In Hire Charges Due To Change In Fuel Rates Sha Ll Be Affected At The End Of Quarter, Irrespective Of Start Of Contract I.E. 8 17On 31St March, 30Th June, 30 Sept, And 31St December. The Change In Hire Charges, If Any, Shall Be Applicable From The Ist Day Of Next Quarte R. Base Rate Of Fuel Would Be Fuel Prices As On Date Of Award Of Contrac T. However, Decision Of Bsnl Whether To Enhance Fuel Price Or Not Is Final. Revised Fuel Rate Would Be The Fuel Prices On First Day Of The Quarter. Increase Or Decrease In The Hire Charges Due To These Variations Shall Be Worked Out From The Base Rate On The Following Formula: - Monthly Km Hire Slab ( I.E 1500 Kms ) X ( Revised Rate Per Litre - Base Rate Per Litre ) Average Km Per Litre Of Diesel Petrol Consumption ( Kmpl ) ( Note:- The Base Rate Of Petroldiesel Is The Prevailing Rate On The Date Of Commencement Of Work Contract. The Average Kmpl Is To Be Assumed As 18 Km Per Liter In Case Of Type I V Ehicle ( Sedan ) And 12 Km Per Liter In Case Of Type Ii ( Suv ) . If There Is Decrease In Fuel Price, Formula Will Indicate Negative Gure Which Means The Deduction Shall Be Done From The Bill ) C. The Service Provider Shall Submit Supplementary Bill For Reimbursem Ent Towards Increase In Fuel Price On Monthly Basis Without Accumula Tion. This Supplementary Bill Is To Be Supported With Proof Of Fuel Price St Prevailing On 1 Of The Month. 15. Termination Of Contract L ) In Case Of Any Default By The Service Provider And In Any Of The Terms & Conditions ( Whether General Or Special ) , Bsnl May Without Prejudic E To Any Other Rightremedy Which Shall Have Accrued Or Shall Accrue T Hereafter, Terminate The Contract, In Whole Or In Part, By Giving 2 Clear Working Days Notice In Writing To The Service Provider. M ) All Instructions, Notices And Communications Etc. Under The Contract Given In Writing And If Sent To The Last Known Place Of Business, Shall B E Deemed To Be Served On The Date, Even In Ordinary Course Of Post, T Hese Would Have Been Delivered To The Service Provider. N ) Notwithstanding Anything Contained Herein, Bsnl Also Reserves The Ri Ght To Terminate The Contract At Any Time Or Stage During The Period Of Contract, By Giving Two Days Notice In Writing Without Assigning Any Re Ason And Without Incurring Any Financial Liability Whatsoever To The Ser Vice Provider. 16. Termination For Insolvency: Bsnl May Also By Giving Written Notice And Without Compensation T O The Service Provider Terminate The Contract If The Service Provider B Ecomes Unwilling, Bankrupt Or Otherwise Insolvent Without Aecting Its Right Of Action Or Remedy As Hirer. 17. Insurance : The Insurance Cover Protecting The Agency Against All Claims Applicabl E Under The Workmens Compensation Act, 1948 Or As Per Any Act In I 9 17Ndia From Time To Time Shall Be Taken By The Service Provider. The Ser Vice Provider Shall Arrange Necessary Insurance Cover For Any Persons Deployed By Him Even For Short Duration. Bsnl Shall Not Entertain Any Claim Arising Out Of Mishap, If Any, That May Take Place. In The Event Of Any Liabilityclaim Falling On Bsnl, The Same Shall Be Reimbursed Inde Mnified By The Service Provider. 18. Prices: O ) The Rates Should Be On Monthly Basis. The Rate Extra Per Km Running And Extra Duty Hrs Are To Be Indicated. P ) Rates Charged By The Service Provider For The Services Given Under T He Contract Shall Not Be Higher Than The Rates Quoted By The Service Provider In His Bid. Q ) In Case Of Any Reduction Of Taxes And Statutory Levies ( If Any ) During T He Contractual Period, Bsnl Shall Take The Benet Of Decrease In Such Taxes Duties For The Services To Be Availed From The Date Of Enac Tment Of Revised Duties Taxes. R ) In Case Of Increase In Taxes Duties During The Contractual Period, Bs Nl Shall Be Liable To Revise The Rates As Per New Taxes Duties For The S Ervices To Be Availed For The Remaining Period Of The Contract. 19. Contractor Is Required To Get Signed The Duty Slips In Prescribed Format At Ann Exure-V By The User For Need Basis Vehicles. Contractor Is Required To Get Signe D Daily On Summary Sheet By The User And At The End Of The Month Finally Get Ve Rify The Summary Sheet By The User In Prescribed Format At Annexure-Vi. 20. Bid- Evaluation:- During The Evaluation Process, The Documents May Be Clas Sified In Two Categories :- A ) Essential Documents: - Experience Certificate, Solvency Certificate, Emdbid Security Or Mse Bodies Udyam Certificate In Case Of Exemption From Emd Which Makes The Bid Valid. B ) Other Documents: - All Other Document Like Epf, Esi, Pan Card Etc Except Ess Ential Documents. Copy Of Rc Has To Be Submitted To Identify The Model Of The Vehicle. Tec Reserve Right To Collect Documents Other Then Essential Documents Directly From The Bidder Within Time Frame And Submit Conclusive Repor T To Tendering Authority. In Absence Of Essential Documents Bid Sh All Be Treated As Invalid 21. Calculation Formula For The Service $Total = $Quantity*$Cost*$Duration_In_Months $Quantity = Number Of Vehicle ( S ) 10 17 $Cost = Monthly Base Fare ( Per Package ) Inclusive Of Gst $Duration_In_Months = Duration In Months 22. The Format Of The Performance Security Bond Is Attached As Per Anne Xure-Vii. 23. Estimate Value ( Tender Cost ) Calculation As Under:- S. Vehicle Ty Monthly No Of Veh Monthly Ch Annual Esti Extra K Extra Ho No Pe Package Icles Arges In Rs Mated Char M Char Ur Charg As Per G ( Excluding Ges In Rs Ges In R Es In Rs. Em Gst ) ( Excluding S. ( Excl ( Excludi Gst ) Uding G Ng Gst ) St ) Type-I ( Sed 1500 Km 1 An ) X 320Hrs. 7 30470 2559480 12 30 7 2559480 Scope Of Work The Bidder Is Required To Provide Commercial Vehicles Fully Conforming To Rtar To Regulation Along With Fuel, Driver Etc And Carryout Periodical Maintenance An D Execute The Work Through Their Supervisor. The Work Consists Of One Part On Monthly Slab Rate. Period Of Contract: Under Normal Circumstances The Contract Shall Be Valid For A Period Of One Yea 11 17R From The Date Of Agreement. However Contract May Be Extended On The Sam E Rate, Terms & Conditions Unilaterally By Bsnl For A Further Period Of Six Months At A Time And Upto A Maximum Of One Year, As May Be Decided By Th E Competent Authority, After Review Of Performance. Scheduled Works Monthly Km Hire Slab: As Per Monthly Requirement The Vehicles Will Be Requisitioned. The Monthly Km Hire Slab On Which Vehicles Are Required And The Number Of Such Hiring Per Month Are Tentatively Indicated Below. Area Of Operation Monthly Hire Slab Quantity Of Hired V Ehicle ( Sedan Typ E ) - ( Petroldiesel Cng ) -Type-I # 1500 Kms And 320 Hrs Per Mo 07 Jaipur Ba Nth 07 # Jaipur Ba: Jaipur Oa ( Includes Revenue District Dausa & Jaipur ) , Sawai Madhopu R Oa ( Includes Revenue District Karauli & Sawai Madhopur ) And Tonk Oa Including Tonk Revenue District. # Note: The Tables Shown In Schedule Of Work Above Are Only Indicative And For Re Gular Work. The Actual Deployment May Vary From Time To Time Depending On Work Schedule, Companys Policy, Intensity Of Maintenance And Interruption Duties And D Evelopmental Activities Etc. However, The Area Of Operation Of Vehicles Is Jai Pur Ba Only But Depending On The Requirements Of Emergent Nature The S Ame Can Be Taken As Rajasthan Circle. Annexure-I Statement Of Vehicles Owned On Lease By The Bidder Bidders Name: Companys Name: Details Of Ownedon Lease Vehicles As Mentioned In Nit As On Date: 12 17Vehicle Owner S Na Vehicle Ty Validity Details Registratio Mode Date Of S. Me Pe N Numbe L ( Ye Registratio Permit Fitnes Insuranc R Ar ) N Road N. S E Tax 1 2 3 4 5 6 7 8 9 10 11 Note: Use Additional Sheets If Required. Declaration: The Details As Above Furnished Are Correct And True. I Undertake To Produce O Riginal Documents Of The Above Said Vehicles For Verification As And When Call Ed For. Date Bidderss Signature Office Seal 13 17Annexure-Ii Specimen Form Of Solvency Certificate From The Schedule Bank This Is To Certify That To The Best Of Our Knowledge And Information That 1 ( Name Of The Individual Or The Firm ) 2. .. ( Name Of The Proprietor In Case Of A Sole Proprietorship Concern Or Name Of Partners In Case Of Partnership Concern As Per Banks Record. 3. . ( Address Of The Customer As Per Bank Record ) Is Aare Customer ( S ) Of Our Bank, Isare Respectable And Can Be Treated As Good For Any Engagement Up To A Limit Of Rs. ( Rs.......................................................................................... Only ) This Certificate Is Issued Without Any Guarantee Or Responsibility On The Bank Or Any The Officers. Manager Bank Annexure-Iii Near Relationship Certificate: ( Format Of The Certificate To Be Given By The Bidder In Respect Of Status Of Employment Of Hi 14 17S Her Near Relation In Bsnl ) The Format Of The Certificate To Be Given Is I..So.Ro..Hereby Certify That None Of My Relative ( S ) As Den Ed In The Tender Document Isare Employed In Bsnl Unit As Per Details Given In Tende R Document. In Case At Any Stage, It Is Found That The Information Given By Me Is False Incorrect, B Snl Shall Have The Absolute Right To Take Any Action As Deemed Twithout Any Prior Intim Ation To Me. Signature Of Authorized Signatory ( Name ) Designation In Company Seal Stamp Of Company With Date And Seal Annexure-Iv Form For Bid Security Declaration ( On Companys Letter Head ) References: 1. Bsnl Tender Enquiry No. Tender No. .........................Issued On ----2022 2. Department Of Expenditure Office Memorandum No. Dpe 7 ( 4 ) 2017- Fin. ( Part -I ) Dated 19.11.2020 Issued By The Ministry Of Heavy Industries & Public Enterpr 15 17Ises. Iwe, In Capacity Of Authorized Signatory Of Ms ..................................................Having Registered Oce At ............................................................................... Being A Participant Bidder In Bsnl Tender Enquiry Cited At Reference 1 Above, Hereby Declare That I Have Und Erstood The Bid Security Provisions And Agree That Iwe ( Bidder ) Will Be Suspend Ed Debarred Banned For The Period Of One Year On Account Of Withdraw Or Mod Ify Their Bids During Period Of Validity Etc., As Per Instruction Issued Vide Om Cite D At Reference 2 Above. Signature Of Authorized Signatory ( Name ) Designation In Company Seal Stamp Of Company With Date And Seal . 8. Buyer Added Bid Specific Atc Buyer Uploaded Atc Document Click Here To View The File. Disclaimer The Additional Terms And Conditions Have Been Incorporated By The Buyer After Approval Of The Competent Authority In Buyer Organization, Whereby Buyer Organization Is Solely Responsible For The Impact Of These Clauses On The Bidding Process, Its Outcome, And Consequences Thereof Including Any Eccentricity Restriction Arising In The Bidding Process Due To These Atcs And Due To Modification Of Technical Specifications And Or Terms And Conditions Governing The Bid. Any Clause ( S ) Incorporated By The Buyer Regarding Following Shall Be Treated As Null And Void And Would Not Be Considered As Part Of Bid:- 1. Definition Of Class I And Class Ii Suppliers In The Bid Not In Line With The Extant Order Office Memorandum Issued By Dpiit In This Regard. 2. Seeking Emd Submission From Bidder ( S ) , Including Via Additional Terms & Conditions, In Contravention To Exemption Provided To Such Sellers Under Gem Gtc. 3. Publishing Custom Boq Bids For Items For Which Regular Gem Categories Are Available Without Any Category Item Bunched With It. 4. Creating Boq Bid For Single Item. 5. Mentioning Specific Brand Or Make Or Model Or Manufacturer Or Dealer Name. 6. Mandating Submission Of Documents In Physical Form As A Pre-Requisite To Qualify Bidders. 7. Floating Creation Of Work Contracts As Custom Bids In Services. 8. Seeking Sample With Bid Or Approval Of Samples During Bid Evaluation Process. 16 179. Mandating Foreign International Certifications Even In Case Of Existence Of Indian Standards Without Specifying Equivalent Indian Certification Standards. 10. Seeking Experience From Specific Organization Department Institute Only Or From Foreign Export Experience. 11. Creating Bid For Items From Irrelevant Categories. 12. Incorporating Any Clause Against The Msme Policy And Preference To Make In India Policy. 13. Reference Of Conditions Published On Any External Site Or Reference To External Documentsclauses. 14. Asking For Any Tender Fee Bid Participation Fee Auction Fee In Case Of Bids Forward Auction, As The Case May Be. Further, If Any Seller Has Any Objectiongrievance Against These Additional Clauses Or Otherwise On Any Aspect Of This Bid, They Can Raise Their Representation Against The Same By Using The Representation Window Provided In The Bid Details Field In Seller Dashboard After Logging In As A Seller Within 4 Days Of Bid Publication On Gem. Buyer Is Duty Bound To Reply To All Such Representations And Would Not Be Allowed To Open Bids If He Fails To Reply To Such Representations. This Bid Is Governed By The General Terms And Conditions , Conditons Stipulated In Bid And Service Level Agreement Specific To This Service As Provided In The Marketplace. However In Case If Any Condition Specified In General Terms And Conditions Is Contradicted By The Conditions Stipulated In Service Level Agreement, Then It Will Over Ride The Conditions In The General Terms And Conditions. In Terms Of Gem Gtc Clause 26 Regarding Restrictions On Procurement From A Bidder Of A Country Which Shares A Land Border With India, Any Bidder From A Country Which Shares A Land Border With India Will Be Eligible To Bid In This Tender Only If The Bidder Is Registered With The Competent Authority. While Participating In Bid, Bidder Has To Undertake Compliance Of This And Any False Declaration And Non-Compliance Of This Would Be A Ground For Immediate Termination Of The Contract And Further Legal Action In Accordance With The Laws. 26 ---Thank You --- 17 17 X 320 Hours; Local Total Quantity :

BRR : 9545191 Tender For Provision Of Solar Power Plant At Sevoke Mil Station Under Ge Sevoke Road.; 2 Design, procurement, erection, installation, testing and commisioning including connecting to local utility grid; Grid connected solar photovoltaic plant 0.8 MW output peak capacity with net billing arrangement including Solar Photovoltaic Modules,DC Cabling, Module Mounting Structures (suitable for ground mountingwith and including Soil Investigation as per OEM recommendation, RCC foundation framed structure and other connected civil work duly vetted by IIT / NIT), Array Combining Boxes, ACDB, DCDB, Lightining Protection of SPV modules and other accessories, String Inverter as Power Conditioning Unit, Weather Station and Data Monitoring system (SCADA) all as per detailed specifications given in tender documents, latest MNRE/SECI/NISE/IREDA guidelines and directions, meeting the Make in India (DCR), consisting of all requisite accessories (BOS-Balance of system) and including the following main components (NOTE : The work shall be executed directly by OEM only through contractor.) Item Continued as 1.01 to 1.45 3 (A) Photo Voltaic Module: Mono-crystalline Silicon Bifacial Solar Photovoltaic Modules of minimum 550 Wp(module power and number of modules to be selected according to available area), having cell efficiency more than 20% under standard conditions, form fill factor more than 0.76, plant performance ratio > 75%, made of high transmitivity glass front surface and it shall give high encapsulation gain (transmittance above 90% and bending less than 0.3%). The modules shall have the following features :(a) The electrical parameters of SPV modules under standard test condition of irradiance 1000W/sqm, AM 1.5 Spectrum and temp 25 degree Celsius shall be as under : (i) Max Peak Power Pmax : 550 Wp or more (ii) Voltage at Max Power : > 40 V (iii) Current at Pmax :> 10A 4 (iv) Short Circuit Current :> 12A (v) Open Circuit Voltage :> 47 V (vi) Module Efficiency : > 20%(b) Rated output of the modules shall have positive tolerance of 3-5% and no negative tolerance is allowed.(c) It shall perform satisfactorily in RH 85% with temperature up to +85 degree C and should withstand wind of 200 kmph on the surface of panel.(d) PV modules shall be warranted for their output peak watt capacity, and it shall not fall of its initialvalue below 90% in first 10 year end and 80% after the end of 25 years.(e) Each module shall have RFID tag encapsulated with solar cell bearing following details (i) Name of Manufacturer of SPV Module (ii) Name of Manufacturer of Solar Cell 5 (iii) Month and year of Manufacturing (separately for cell and module) (iv) Country of Origin (both cell and module) (v) Peak wattage, Im, Vm and fill factor of the module (vi) Date of year of obtaining IEC PV module qualification certificate including the test lab issuing IEC certificate. (vii) Unique serial no of model no of module (viii) IV curve of module(ix) Other relevant information on traceability of solar cells & modules(f) The temperature coefficient of power for the module shall not be more than 0.50% per degree Celsius.(g) The module must have bypass diode of suitable capacity.(h) PV module must confirm to latest edition of IEC 61215/ IS 14286. In addition the modules must confirm to IEC 61730 Part I and II for construction and testing & safety qualifications and confirming to IEC 62804 PID.(j) It shall also be in conformity to latest minimum technical specification issued by MNRE/IREDA/SECI/NISE/ALMM from time to time. Modules should be of MNRE/IREDA/SECI/NISE/ALMM approved companies and as per latest IEC/IS standards. 6 (k) RFID reader is to be provided by contractor(l) Both PV cells and SPV modules shall be made in India (DCR).(m) Each structure should have angle of inclination as per the site conditions to generate maximum power. However, to accommodate more capacity the angle inclination may be reduced to 10 - 13 Degree until the plant meets the specified performance ratio requirements.(n) Fire Points with Fire extinguisher liquefied CO2 gas of capacity 10 kg and adequate qty confirming to relevant IS or ISI mark complete as recommended by manufacturer deemed to be included in the unit rate quoted.(o) Danger Board and Rubber mat as recommended by manufacturer deemed to be included in the unit rate quoted.(p) S&F Pressure Booster pump electrically operated with minimum 3 HP 02 Nos (Running+ standby) three Phase AC Supply motor and having head not less than 20 mtr, including PCC foundation civil wokrs and necessary cable required for connection in drawn in PVC conduit heavy duty/ DWC/Electrode pipe from existing nearest point to the motor starter panel including motor starter suitable capacity,PP-R IS-15801 (Polypropylene random co-polymer) pipe 3-layer 63 mm/50 mm/32 mm/25 mm inner dia (outer green coloured UV stablilized, middle black coloured UV stabilized and innermost layer white coloured with anti-microbial property) fusion welded grade PN-10 SDR-11 ( Pressure nominal 10KGS/cm2 ) having thermal stability for hot & cold water supply including all types of plain and brass threaded PPR fittings of any size such as elbow, tees, FTA and MTA etc laid in trenches with necessary exavation, removing and returning filling work and including all accessories from the new PVC tank cap 10000 Ltrs install at proposed site for cleaning of entire solar power plant system.(q) SPV Panel is to be fixed in such a way that lower portion of the Panel remains atleast above 1.5 mtr of finished reflecting surface and cost deemed to be included in the quoted rates. 7 (B) Junction Boxes: Junction boxes of suitable Nos (as per design)/OEM recommendations inputs and suitably rated out put having separate DCfuses for both (+)&(-) on input and isolator on output terminal for each string.Each junction box must have as pare input terminal.The junction boxes shall be dust and vermin proof and water proof made of FRP/ Thermo Plast with IP 65 protection in compliance with IEC 62208 and shall be UV resistant, fire retardant. It shall have surge protection and maintenance free earthing as per relevant standard. The junction box shall have suitable arrangement of the following: (a) The strings are required to be connected to the copper bus bar through individual fuses. (b) Provide arrangement for disconnection (DC dis-connection switch) for each SJB/ SCB. (c) To provide a test point for each sub group for quick fault location and to provide group array isolation. (d) Each array box shall be of relevant IEC standard. (e) Each array junction box shall have suitable bypass & reverse blocking diodes for minimum DC blocking voltage of 1000V with suitable arrangement of its connection. Reverse blocking and bypass diodes shall work for extreme temperatures and shall have efficiency of 99.98% confirmed by appropriate IEC standard. 8 (C) DC Cables: Suitable size of XLPE insulated tinned Copper cable (min 10 sqmm) of solar grade, 1100 Volts and UV resistant for outdoor installations confirming to IEC : 60227/15694 & 60502/ IS : 1554 (Pt I&II)) and shall be as under : (a) All cables and connectors must be as per IS/IEC standards and shall be able to withstand harsh environmental conditions including high temperature, UV radiations, rain, dirt, burial and attack by moss and microbes for 25 years and voltage as per latest IEC/IS. (b) All the cables / wires shall be provided with UV resistant printed ferrules for DC wires. (c) The size of the cable shall be such that average voltage drop at full power from PV module to inverter shall be less than 1.5%. (d) Cable batch No., Drum No, IS code and size and make shall be mentioned on every one meter or as per OEM practice. (e) The wiring of the module interconnection shall be in UPVC/HDPE pipe of suitable size. (f) The cost of interconnecting DC Copper cable, MS cable trays, MS cable trays suitable to accommodate Solar grade cables from SPV module to inverter are included in the item. 9 (g) Boring of holes under road, pavement, hard standing by trenchless technology (HDD) GI protection pipe up to 100 mm bore (dia), maximum 2.5 metre below of apron areain ant type of soilcomplete.Note : (i) All the precaution to be taken by the contractor before drilling the bore. The contractor has to take plan of existing cables any type and pipe line in existing area before drilling the bore. (ii) Any damage to existing cables any type and pipe line in the way of drilling the bore will be repaired and make good by the contractor within 24 hours. No extra cost will be paid in this account. (iii) Contractor has to get the survey of route, length and depth for boring before quoting the rate. (iv) Connected items like HDPE/PPR/DWCPE pipes, exavation, removing, return filing, channel, any type of metal work is not measured and paid separately under relevant items.(D) Module Mounting Structure (MMS) (Suitable for ground mounting on any type of soil condition) :Design, procure, fixing, support structure made of hot dipped galvanised steel with min 85 micron thickness including necessary PCC / RCC foundation and associated work (cutting, grounding, PCC filling, disposing waste material,etc., complete) and fixing mounting arrangement suitable for SPV modules so as it can with stand wind speed of 170 km per hour & minimum yield strength off 250 MPa. The mounting structure is to be installed on ground. Mounting structures to be so designed that maximum load is directly on ground. It shall also observe minimum space without sacrificing the out put of SPV panels & adequate spacing between the arrays shall be available for easy cleaning and maintenance. Nuts, bolts, protected from the atmosphere and weather mounting structure shall have to be adequately of Stainless Steel of grade SS316. 10 NOTES :- (a) Two numbers of anti theft fasteners of Stainless Steel on two diagonally opposite corners of each module shall be provided. (b) Module mounting structure shall be fitted to provide maximum generation. (c) MMS design shall be supported with Staddpro Report vetted by Third Party (Gov Institute) and submitted for the approval of the Accepting Officer. (d) The height of approved design MMS for solar power plant shall be as per latest MNRE/IREDA/SECI/ NISE guidelines. (e)Minimum grade of RCC M-25, design mix (using 20mm graded crushed stone aggregate includingTMT bar as per design, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and other connected works as per design and OEM recommendation. Civil work shall be designed through approved consultant of MES as per latest MNRE/IREDA/SECI/ NISE guidelines and vetted by IIT / NIT.(E) Lightning Protection forentire Solar Power Plant (i.e PV Array, Inverter etc) : Design, procure and fix lighting arrestor system confirming toIS/ IEC-62305(Part1-4)on the ground. The air terminal shall be fixed at the top of MS pole with base so as to beat least two meter above the pole to be protected. Its height above 9 mtr level shall be depend upon the level of protection and protection radii required. 11 NOTES :-(i) The cost of all equipments, MS Pole, Copper strip upto earth test point,LA, etc., shall be deemed to be included in this item. (ii) The cost of sufficient earthing for lightning protection is also included in this item to be provided by Engr-in-charge. and no extra payment will be made to the contractor on this account (iii) The complete system shall include chemical earthing (as per OEM recommendations) and earth strip/cable etc for earth of SPV module, array, inverter,DC & AC boxes and for LA etc as per latest IS/MNRE/IREDA/NISE/SECI/ALMM specifications and guidelines.No separate cost of the same is included in the schedule and amount will be paid to the contractor on this account. In case of any dispute, decision of Engr in charge will be final, conclusive and binding to contractor. (The earthing shall be of copper earth plate and having specification as per SSR Item Sr 19474). Earth resistance shall not be more than 3 Ohms. (iv)Separate LA arrangement & the design document of the same shall also be submitted. (v) The protection against induced high voltage shall be provided by the use of metal oxide varistors and suitable earthing such that induced transient find and alternate route to earth. (vI) SPV Power Plant shall be provided with lightening and over voltage protection. (vii) Internal surge protection shall consist of three MOV type surge-arrestors connected from +ve abd +ve terminals to earth (via Y arrangement) 12 (F)Power Conditioning Unit: Procure, fixing, testing and commissioning of minimum 4 (Four) unitswith overall not less than 800 KW output on 11 KV AC supply, Solar-power inverter suitable for without DC power of Solar PV module/ array with AC output further feeding to grid confirming to IEC:61683 for efficiency, IEC:62109-1 or equivalent for safety and IEC:62093 for reliability. The input DC & output AC technical specification of Inverter are as under :Input (DC) (a) Max Absolute DC input Voltage : 1000 V (b) Start-up DC input voltage : 200 - 500 V (Default 420V) (c) Operating input DC voltage range : 200 - 1000 V (d) No of independent MPPT : One (e) MPPT input DC voltage range at Pacr : 180 - 1000 V DC (f) Max input DC Current : As per design. (g) AC grid connection type : 3Phase (4W + PE) (h) AC output power : As per design. (j) Max AC output Apperant power : As per design. (k) Max AC output Current : As per design. (l) Max AC fault current : As per design. 13 (m) Nominal Output Voltage : 800 Volts AC 3phase or as per the design of Solar Stepup Transformer (n) Output voltage range :± 10% (o) Output Frequency : 50 Hz ± 3Hz (p) Power factor : > 0.99 (q) Harmonic Distortion Current : < 3% (r) Efficiency : > 98% (s) Standby operation consumption : < 1.5 W(t) Operating temperature upto 85 degree centigrade (u) The Copper based inverter shall have minimum IP-67 protection, ground fault monitoring, reverse polarity protection, anti-islanding, DC reverse polarity, AC and DC short circuit current and over current, AC and DC over voltage and over temperature. 14 (v) The inverter shall adjust voltage and frequency levels to suit the grid. (w) The inverter shall be self commulated with Pulse Width Modulation (PWM) technology and shall be capable of synchronise maximum with in one min. (x) Maximum Power Point Tracker (MPPT) confirming to IEC 62093 shall be integrated in the inverter to maximise the energy drawn from the PV array (y) Monolithic design of inverter is not permitted. (z) Shall have anti-Islanding features. (aa) The inverter shall have suitble nos of protected inputs (asper design) and outgoing shall be protected by ACB/MCCB. (ab) The inverter should have MODBUS, PROFIBUS, ETHERNET common ports. (ac)The inverte rshall include appropriate self protection and self diagnostic features to protect itself and the PV array fromthedamageintheeventof invertercomponent failureor fromparametersbeyondtheinverterssafeoperatingduetointernaland/orexternalcauses. Invertershallhaveprotectionarrangementagainst ground leakage faults, over voltage, (SPD) & over current. Inverter shall have arrangement for adjustment for adjusting DC input current and shall trip against sustainable fault down stream and shall not restart till fault is rectified. (ad) The inverter should have provisions of Galvanic isolation, anti-islanding protection (IEEE 1547/UL 1741) equivalent IS and lightening. (ae) PCU must have the feature to work in tandem with other similar PCUs and be able to be successively switched ON and OFF automatically based on solar radiation variations during the day. (af) Minimum Warranty of Inverter- 12(Twelve) Years and defect liability period deemed to amended accordingly for the said item. 15 (G)ACDB : Outdoor type powder coated weather proof,vermin proof made out of CRCA sheet front open able door, lockingarrangement, including suitable working space in DCDB busbar chamber, cable box chamber including Copper busbar of designed capacity /bus raisers suitable capacities with PVC sleeves/tape RYB colour for phases identification, including all bus raiser shall be extend upto cable box chamber fixed on fibre insulation for RYB & neutral to all out going cable, confirming to IP-65 and fixed on wall / floor with control wiring with comprising cable gland brass, copper lugs etc. and comprising the following as per design :- (i) MCCB 4Pmicroprocessor based for outgoing (ii) MCCB 4Pmicroprocessor based for incoming (iii) AC type 2 Surge Protection Device (iv) Spreader Terminals as per requirement (v) Multifunction meter (vi) CT of suitable ratio(vii) Copper busbar chamber (ix) The earthing shall be of copper earth plate and having specification as per SSR Item Sr 19474).Earth resistance shall not be more than 3 Ohms. 16 (H) DCDB:- Outdoor type powder coated, weather proof, dust proof,vermin proof made out in CRCA sheet front open able door, looking arrangement, including suitable working space in DCDB busbar chamber,cable box chamber including copper bus raisers with PVC sleeves/ tape RYB coloursfor phase identification, including all bus raiser shall be extend upto cable box chamber, confirming to IP-65 and fixed on wall /floor with contral wiring with comprising cable gland brass, copper lugs etc. (i) MCCB as per requirement (ii) Fuse as per requirement (iii) Copper busbar chamber. (I) Weather Monitoring System Pyranometer : The pyranometer (ISO 9060 classification ) alongwith necessary assessories for measuring incidental solar radiation at horizontal and inclined plane of array. Specifications of the pyranometer shall be as follows :- (i) Spectral response : 031 to 2.8 micron,(ii) Time response (95%). Max 15 second 17 (iii)Nonlinearity + 0.5% (iv) Temperature response : - 2%(v) Tilt error <+/- 0.5% (vi)Zero offset themal radiation +7W/Sqm (vii) Zero offset temperature change + 2 W/Sqm(viii) Operating temperature range - O °C to 80°C(ix) Non stabillity Maximum - 0.8%,(x) Resolution minimum +/-1 W/Sqm (xi)Output Analog 4.50mA (xii) Digital RS 485(xiii) The earthing shall be of copper earth plate and having specification as per SSR Item Sr 19474).Earth resistance shall not be more than 3 Ohms. 18 (J)Balance of System(BOS) Items/ Components:TheBOSitems/componentsof theSPVpowerplants/systems deployed under this project shall conform to the latest edition with certificate of IEC or equivalent BIS Standards/MNRE specifications/ as specified in Para 1.01 of Minimal Technical Requirements/ Standards for SPV System/Plants to be deployed during this financial year under the programmes of MNRE available on MNRE website as on last date of quoting of tender. Notes:(i) The contractor must visit the site before quoting the rates for this item to assess the site condition so as to decide up on location and layout of SPV, placement of inverter, length of DC cables, lightning arresters, etc., complete. (ii) The contractor shall submit complete scheme including electrical diagram of the work, schematic diagram, SPV module layout, placement of LAs, Civil work, etc., complete as per IREDA/ SECI/NISE/MNRE/ALMM latest guidelines as applicable, Relevant IEC/IS norms to the GE for approval with in one month of date of commencement of the work. (iii) The rate quoted is deemed to be inclusive of the all protection system including surge, lightning arresters and necessary earthing all as specified and directed. 19 (K) Remote monitoring system (SCADA) for solar power plant complete with all electronic andelectricial partswith andincluding all necessary software and hardware etc to make fully functional connected to LED monitor (55 inches) with complete plant parameters as required and operate the system from remote and Other Accessories includingandThe system will be controlled from the main control room where all the data from different parts of the plant shallbe received, analyzed and action taken either manually or on auto as per the system design by OEM . The SCADA shallhave remote monitoring capability comprising with the following Items and with and including all connectedaccessories as per OEM recommendation complete:(a) Main SCADA control wall mounting panel complete with fixing arragnment like nut bolt, washers suitable size and connected items. (b) LED Moniter (55. inches) with mouse, key board, CPU (Minimum 1 TB storage alongwith 12 GB RAM, i7 processor), key pad and single phaseUPS 10 KVA with 12 Volt battery, 14400 Ah battery bank with rack and required battery backup should not be less than 4 Hrs inside control room.(c)“SCADA System shall be audited for Cyber Security by CERT certified firms at the time of commissioning. Subsequent cyber security audit shall be carried out after every 03 years and cost of audit and rectification shall be born by the contractor” 20 The Contractor shall provide following defined user access levels, unless otherwise instructed by the Engineer-in-Charge: -• Normal viewing only (default level) The default level shallpermit users to view al displays except those specifically assigned to a higher level of access.• Dally Access The daily access level shall allow viewing (ie default an printing at trend displays.• Operator Level (Remote Control) The operator level shall permit authorised users to access lower levels a and to carry out the following actions:- Perform control actions Acknowledge alarmsEnter or modify manually-entered data for inclusion in thereports.• Monthly and Yearly Data Archiving The level shall permit authorised users to access lower levels and shall provide the facility to download specific data to long ten data storage for archive purposes(d)The SCADA software shall be of a proven design and reliable, and conforming to industrial standards and shall: -• Support multiple makes of RTU/ Microprocessor controller/ transmitters and models and provide required software features needed to easily adapt a device whichshall not be supported as standard to the SCADA system. 21 • RTU/ PLC/ Microprocessor base controllers and transmitters shall have an expandable architecture and scalability to provide future capacity increases in SCADA system as well as meet present needs of the administration, provide multi-level security and password mechanisms to prevent use of the system by unauthorised persons. The access privilege of authorised users shall be defined separately and permission shall be provided to the users only to access areas concerning them, provide an on-line operatingenvironment.• Adding a new RTUI Microprocessor based Controller to the SCADA system or changing configuration of the existing RTUs/ Microprocessor based controller shall not result in stopping or hinder working order of SCADA system.• The Contractor shall specify maximum number of data which shall be achieved by the system without any performance loss. The Contractor shall conduct necessary tests to prove maximum number of data points achieved. The Contractor shall also be responsible to create additional data points necessary for conducting such tests. Any AutoCAD graphics shall be able to be converted to process diagrams and shall be re-loaded and operated after completion of all works and during tests.(e)The Contractor shall hand over to MES the SCADA and application software (as CDs or DVDs) necessary for re-loading software to the system in case of failures The CDs or DVDs shall be provided after making the necessary tests. The operating system ofrouters and work stations shall be of an architecture that provides a multi-tasking operating environment, and SCADA software shall also be multi-tasking. Therefore multiple tasks such as receiving measurement results from devices, displaying these results on computer screen. storing on a computer disk, sensing alarm conditions that may occur based on measurement results, and displaying them to users, generating reports from collected data, and printing them cut, transferring issued commands to Microprocessor controllers/ RTUs/ PLC, that SCADA software is supposed to execute shall be handled simultaneously without one task waiting for another. 22 To configureSCADA software or to change the system configuration, definitions shall be either defined directly by using a keyboard or another interactive tool or mechanisms that allow importing of configuration definitions from a text file created with a text editor. The database configuration shall be provided by means of an interactive program that contains menus or similar approaches and shall be easy to use The database configuration definition program, when required, shall be capable of extracting definitions related to the configuration from information created in text format to use as definitions for configuration The following shall be possible online without interruption or hindering of usual operations: -•Adding an RTU to the SCADA system.•Deleting an RTU from the SCADA system•Changing configuration information related to an existing RTU definition.•Modifying definitions in database containing information about measurement and control points.•Creating screen pictures which offer operators to monitor and control the SCADA system.•Similar configuration changes. 23 (f)SCADA software shall be upgradeable to new versions with an automatic mechanism to be provided by the Contractor. The old version of software shall be overwritten by new version without resulting in a change in any of the definitions created in previous version, nor disturbing the operational logic defined in previous version. Al! text being available on the screen shall be in English language The database shall be configured on-line when the SCADA system shall be in operation. The changes on existing definitions or new definitions related to database shall be made when the data collection n and control functions are being performed. The SCADA Software shall be operated using the database that shall be resident in the memory(g)Data Exchange The control system shall provide a method of real-time data exchange with different application programs like Geo Information System (GIS). relational database, third party spreadsheet packages, report generation and graphical simulation packages.(h) Historical Data Management An historical data management (HDM) system shall be provided for archive, storage and retrieval of operational data comprising field input data, manually-entered data and calculated points Archived historical data shall minimally include averages, minima and maxima for each analogue value compiled over hourly. daily and monthly time periods, with a minimum capacity of 1o00 points. The HDM system shall be capable of selectively increasing the rate of data capture based on events, such as process variable status, discrete inputs, or operator command. Minimum and-maximum data shall include the time and date of occurrence. Gaps in collected data caused by faulty instruments or control system equipment shall not be included in average). minimum and maximum compilations. 24 (j) Report GenerationThe system shall be provided with a report generator utility which shall enable authorised users to create, delete or modify report definitions The report definitions shall allow for retrieval of data from on-line database and farm historical data files and for formatting data for output to printer. The format of each report shall be definable by user to include the definition of static or background data, placement of data base values, number of significant digits of a value, date and time of report and calculated values(k)Graphic Display GenerationThe system shall be provided with an interactive on-screen graphic generation utility which shall allow an authorised user to create new graphic displays and modify or delete existing displays at any work station including those associated with the LCP/ outstations. The generation utility shall include an interactive linkage process allowing user to link symbolic, numeric and bar graph representations and data entry locations to dynamic data base variables. The graphic display system shall be capable of making full use of the VDU resolution in the composition and display of graphic information. Graphic symbols shall be definable by the user for display of static and dynamic data. The user shall be able to as5emble a library of symbols which shall be retrievable into any graphic display. Text and symbols shall be able to be enlarged, shrunk, moved, mirrored or related with reference to a given display. The system shall be able to represent dynamic analogue data on a graphic display as a variable-length, sizeable bar graph, as well as numeric text. 25 (l)DisplaysGeneral all displays, excepting those containing data derived from historical files, shall be completely displayed within two seconds of the operators request. Dynamic data shall be continuously updated while being displayed. All screen displays shall provide following displays which shall be fixed in their locations to normal operations:• Alarm banner window at bottom of the screen display showing last three highestpriority unaccepted alarms. Where the system allows contents of banner to be limited (eg by user name or group) then the selection criteria applied shall be displayed with the banner.• Main display area for user selected displays e.g. mimics, alarm lists, etc.• System dialogue banner window at bottom of the screen shall display relevant system information such as error message and user prompts 26 •A day, date and time indicator shall be able to show local time an alarm bannerarea shall be included on all displays which provide information regarding most resentalarm events. The system shall allow operator to obtain details of most recent alarm event from any operational screen display through direct operation using a maximum oftwo keystrokes or selections. The system shall allow the operator to obtain a print of any display, including graphics through use of a standard system command. Screen displays shall appear identical incorporated form Dynamic data contained on a display shall not change during screen print Such that a snapshot of conditions is portrayed. Each display shall include time of day in hoursminutes and seconds and date in day, month and year format.•A facility shall be provided which allows paging to related displays through the use of ‘page forward or backward keys, or through the use of pick points(m) Suitable size of HT & LT XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 11000 Volts and 1100 Volts grade with stranded aluminium / copper conductor of size as per OEM recommendation and approved design ISI markedincluding cable glands, lugs, jointing kit etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc.with all fixing & connecting accessories and necessary earthwork, civil work deemed to be included in quoted rates of the above items.(n)Generic Displays.The system shall produce various generic displays automatically 27 Metering arrangements: (A)Suitable bi-directional metering arrangements with recording facility shall be provided as per the norms of WBSEDCL. The metering arrangements must have feature to measure and record, (i)Parameters of KW, KWh, KVAR, voltage, current, PF and any other metering required to determine efficiency and efficacy of the system. (B) LT 3 Phase 4 Wire Electronic Tri vector Meter with CT ratioshould be as per capacity of SPV plant. (i) Standard: IS 13779:1999 / CBIP 88 (ii) Accuracy: Class 0.5 (ii) The metering arrangement shall have inbuilt Solar PV Plant synchronisation features. (iii) Reference Voltage - 3x240 V (iv) Basic Current (Ib)- 5 A (v) Maximum continuous current (Imax) - 10 A (vi) Rated Frequency (variation) - 50Hz (±5%) 28 (vii) Power consumption:- Voltage circuit: Less than 1.5 W and 10 VA per Phase at reference voltage, reference temperature and reference frequency Current circuit: Less than 1 VA per phase at basic current, reference frequency and reference temperature (viii) Display type: 8 digit 7 segment backlit LCD display, not less than10 mm character height (ix) Display in the event of Power Failure: Internal battery back-up for LCD display (x)Communication port: Galvanically isolated Optical Communication port for data transfer through either CMRI or remote device or both is providedwith RS 485 for DLMS protocol (C) CT/PT operatedenergy meter with following features (i) True four quadrant metering (iii) Time and day metering with maximum demand registration and automatic billing (iv) LCD display with announciators for various critical events (v) Scroll lock feature for continuous display of a desired parameter on display (vi) High resolution energy display mode for dial test (vii) DLMS protocol for meter reading, with option to remote reading port. 29 (viii) Advanced event detection features for voltage, current and magnetic influence (ix) Meter reading in absence of mains, using internal battery. (x)Power Manager Device Nano type with 4 inverter support with energy monitoring, zero export control, Load Management having RS-485 communication port, ethernet including RS 485 cable core size 0.5-1.5 Sqmm to establish communication between inverters, SCADA and sensor as per OEM recommendation with and including all connectedaccessoriesdeemed to be included quoted rates.(xi) Digital WIND SPEED SENSOR withminimum 3 cup Anemometer range 0 to 70 Mtr/ Sec distance constant 2.5 Mtrs output TTL Pulses output proportional to wind speed and diameter of cup 50mm with brass housing and stainless stell shaft(xii) WIND DIRECTIONSENSOR with wind vane and sensing vain coupledto linear endlsess potentio meter IP 67, range 0-357degrees, operating temperature -40 to +60 degrees celsiuswith brass housing and stainless stell shaft and aluminium vane complete 30 (xiii) AIR TEMPERATURE SENSOR withRTD sensing element PT100 mounted inside a weather shield duly coated with weather proof reflective white paint , range -40 degree to +60 degree celsius with nylon body housingwith weather shield and brass stem to mount the sensor, includingpower requirment 5 Volt DC complete. (xiv) MODULE TEMPERATURE SENSOR Model PT 1000 measuring range -40 Degreeto + 80 Degree Celcius with suitable ouput as required and directed on site and mounting on RTD encapsulated in suitable housing including connecting cables as required complete.(xv)Tipping Bucket Rain Gauge with Magnet and Red Switch type Sensing, rim diameter 203 mm and collecting are 335 MM SQ, Rain gauge shell made up of FRP bucket and mounting made up of stainless steel SS316 and unlimted capacity,including connecting cables as required complete.(xvi)SOLAR Radition Sensor ARN 8101 with 72 element thermo pile sensor and spectral range 0.3 to 3 Micro Mtrs and sensitivity 20 Micro Volt/ W/M², range 0 to 1500W/SQM & output 0 to 25 milli Volt and operating temp -10 to 70 Degree Celsiusincluding connecting cables as required complete with all fixing arrangment and necessary civil work complete with including all connectedaccessories as per OEM recommendation/Designcomplete: 31 (L)Step up solar transformer (800 volt/11 KV)” - Design,procure,erection, installation, testing and commisioning including connecting to local utility grid :Oil filled Type 3 phase, 50 Hz, ONAN cooling type, vector group of appropriatetype, number of load voltage Ratio: number of Phases / Freq.: 3 Phase / 50 Hz., Sealed type Copper wound Transformer with Off Load Tap Changing Arrangement on HV side in steps of 2.5% , +5% to -10% having cable end boxes on HV side suitable for 3 Crore X 300 Sq. mm. XLPE cable of 11 kV grade on HT side and LV side complete with all accessories like buchholz relay, Oil temperature indication, winding temperature indication and alarm etc preferbly DMCR Protection Relay i/c first filling of filtered dehydrated K Class natural Ester Oil bioTransol (as per IS 16659) and confirming to IS 1180 and losses shall be as energyefficiency Level 3 only & 100% load phase, with an impedence of 6.25% i/c as per specification below complete in all respects as required at site. Design ambient to be considered as 50 Deg C.All the balance parameter like temp rise, Basic insulation level, flux density etc shall be strictly in accordance with IS 1180 Part - 1 only including necessary earth work, PCC plinth foundation etc.Heat Run Test is the mandotary test for each Transformer.Standard: The equipment shall conform to the latest edition of applicable standards as follows. In case of conflict between applicable standards and this specification, this specification shall govern.• IS 2026 Standard for Oil filled Transformer• IS:3639 for Fittings and Accessories• IS:2099 for Bushings > 1000 V• IS:7421 for Bushings < 1000 V• IS:1271 for Electrical Insulation classified by Thermal stability• IEC 62770 Natural Ester Oil• CBIP Guidelines 32 (xvii) CORE : Transformer shall be double wound, core type with low loss, non-ageing, high permeability PRIMEGRADE, CRGO with M4 Grade or Better, perfectly insulated and clamped to minimize noise and vibrations. Followings should be Mandatory for any manufacturer: -(a) Transformer shall be of BOLTLESS core design.(b) Core shall be purchased Directly from Manufacturer or from their accreditedMarketingorganization of Repute & not through any agent. Bidder has to submit manufacturer’s name during bidding having sufficient credential & Core has to be purchased from the approved manufacturer.(c) Stage inspection of the core shall be done at manufacturer’s premises & inspection call shall be given with following Documents: (i) Invoice of the supplier (ii) Mill’s test certificate (iii) Packing list (iv) Bill of landing & Bill of Entry certificate by customs(d) Transformer manufacturer should have in-house core cutting facilities for proper control & monitoring of quality & to avoid mixing of Prime core with Second grade /defective core materials. Transformer Manufacturer should have in-house slitting Machine so that core is cut to width & stacked with minimum air gap thus ensuring Burr level less than 10Microns.(e) Core shall be procured from one of these reputed Manufacturers : Posco / Nippon/ Novex/ Ak Steels.(f) The insulation structure for the core to bolts and core to clamp plates shall be such as to withstand a voltage of 2000V for one minute. 33 (xviii)Tank:Tank should be of corrugated wall construction type. The exterior of tank and other steel surfaces exposed to the weather shall be thoroughly cleaned and have a priming coat of zinc chromate applied. The second coat shall be of an oil and weather-resistant nature, preferably of distinct colour from the prime and finish coats. The final coat shall be of a flossy, oil and weather resisting non-fading paint of specified shade. The interior of the tank shall be cleaned by shot blasting and painting with two coats of heat resistant and oil insoluble paint.Winding:(a) Winding shall be made with 99.9% pure electrolytic grade copper, insulated with thermally upgraded paper (Insulation Class A / Conductor Turn Insulation-Class E).The HV & LV winding should be able withstand thermal and mechanical stress in the event of short circuit.(b)Winding shall be carried in dust free area(c) The completed core and coil assembly shall be dried in vacuum and shall be immediately impregnated with oil after the drying process to ensure elimination of air and moisture within the insulation.Oil type: TransformerTransformer oil shall be as per IS-335:1993. It shall be natural/synthetic ester oil. The material safety Data Sheets (MSDS) for the Transformer oil shall be submitted by the bidder along with the offer Temperature Indicator:One set of winding temperature indicators with necessary current transformer, heating coil and a detector element and one set of oil temperature indicator with maximum reading pointer shall be mounted locally so as to be readable at a standing height from ground level. Each of the above indicators shall be provided with necessary contacts for alarm and trip: (a) Oil Insulation class : K class. It should also exhibit safety against fire hazards 34 (b) Cooling : ONAN(c) Vector Group: to be decided during design.(d) Percentage Impedance (Z%) 6.25 %.(e) Transformer Losses:as per IS 1180 - Level 1(2021)(f) Taps on HV for HV variation : +5 to -10 % in steps of 2.5% each (g) Termination (HV): Cable End box for11 KV cableof suitable size(h) Termination (LV): Cable connection(j) The transformer shall be supplied with following fittings:(k) Lifting lugs and Jack lifting pad support(l) Earthing terminals - to be decided during design. 35 (M)Earthing :The complete system shall include chemical earthing of required quantity for step-up Transformer (as per OEM recommendations) and earth strip/cable etc for earth of SPV module, array, inverter,DC & AC boxes and for LA etc as per latest IS/MNRE/IREDA/NISE/SECI/ALMM specifications and guidelines.No separate cost of the same is included in the schedule and amount will be paid to the contractor on this account in case of any dispute decision of Engr in charge will be final and binding to contractor. (The earthing shall be of copper earth plate and having specification as per SSR Item Sr 19474).Earth resistance shall not be more than 3 Ohms. 36 IMPORTANT NOTE FOR SOLAR POWER PLANT CONTRACT (COST DEEMED TO BE INCLUDED IN QUOTED RATES :-(1) The item specification and details given are for guidance purposes only and are likely to vary with modified / higher specification than that specified in the BoQ based on detailed site survey, solar potential assessment, design approval etc keeping the quantity of Solar inverter (PCU) and Solar Transformer same as in the BoQ. The items as per the finalized and approved design and specification, including make, shall be provided by the contractor without any extra cost to the department. All makes should be as per the latest MNRE approved list of makes and models.2.Cost of preparation of DPR design vetting from NISE/MNRE approved Institute and net billing arrangement (as per WBSEDCL) is deemed to be included in the quoted rate.3.The contractor shall submit complete design of Solar power plant, Schemetic/line drawings, detailed mounting structure array layout drawings alongwith SBC report based on the soil investigation as per OEM recommendation, Single line diagram with and including project reportand connected document shall be submitted by OEM through contractor prior to commencement of the work for approval of Accepting officer and subject to the drawing and designduly vetted by IIT/NIT (for mounting structure only) and vetted by NISE/ SECIfor entire scheme of Solar Power GenerationProject including evacuation and Net Metering arrangement complete before recommendation by GE for approval of the accepting Officer. 37 (i) The scope of works involves engineering, procurement & construction (EPC) of entire Solar Power Plant of capacity 0.8 MWp.4. The entire work shall be executed directly by OEMonly through contractor and contractor has to submit the MoU with OEM (agreement period for 25 years of entire Solar Power Plant Project) prior to commencement of work and same shall be approved byGE. 5. Boring of holes under road, pavement, hard standing by trenchless technology (HDD) GI protection pipe up to 100 mm bore (dia), maximum 2.5 metre below of apron areain any type of soilcomplete.Note : (i) All the precaution to be taken by the contractor before drilling the bore. The contractor has to take plan of existing cables any type and pipe line in existing area before drilling the bore. (ii) Any damage to existing cables any type and pipe line in the way of drilling the bore have to berepaired and made good by the contractor within 24 hours. No extra cost will be paid in this account. (iii) Contractor has to get the survey of route, length and depth for boring before quoting the rate. (iv) Connected items like HDPE/PPR/DWCPE pipes for entire Solar Power Plant Project, exavation, removing, return filing, channel, any type of metal work is deemed to be included in the quoted rate. 38 6.Cost of comprehensive maintenance as per OEM recommendation alongwith cost of spare parts required during 5 years of defect liabilty period after completion of Ph-I is deemed to be included in the quoted rate.7. Bidders attention is drawn to pre-bid conferance with department and also visit the site prior to bidding and other factor required as per OEM recommendation deemed to be included in quoted rates.8. The contractor has to carryout Pre-commissioning test of solar power plant including stepup transformer by CEI/SEI. The necessary tools and plants required for inspection of the plant shall be arranged by the contractor.and costsare inclusive in quoted rates.9. Contractor needs to know the irradiance of the location at the project before quoting. The contractor will design DCR (Make in India) for entire Solar Power Plant according to irradiance of the project location and efficiency of the components to produce the desired peak value as mentioned in the schedule i.e. 800 KW output on 11 KV AC supply and inject to the proposed RMU 11 KV. 10. During the execution of work any type of damage by elephant or monkey manance, contractor is fully responsible for protection of all solar power plant equipments including connected items i.e. PV Module, Inverter etc. No claim will be sought from the department. 39 11. All SCADA related activities viz. cables till SMBS and inverter and the requisite software and hardwarefor control room shall be included in the quoted rate.12. Vegetation Growth should be controlled by use of Deweeding Chemicals deemed to be included in Quoted Rates.13. Adequate Water Storage Facility of capacity 10000 Ltrs PVC Tank 5 Layer (with guarantee of 10 years after physical completion of work) on PCC Platform including suitable foundation for cleaning of PV Modules and suitable water drainage facilitiesfor both (Rain Water and Cleaning Water) from proposed site to existing drainage chamber is deemed to be included in the quoted rate.14. Solar Transformer fed from the Inverter should not be having odd harmonics (certificate needs to be required before physical completion of work).15.The Shutdown duration of Inverter should be monitored and recorded and analyzed. 40 16. The SPV Power Plant will be capable of generating 800 kW AC Output atleast once in a year and the AC Output of the plant will be not less than 90% of initial output by the end of 10 yearsand not less than 80% of the initial output by the end of 25 years.17. The Contractor shall operate and maintain Fire Protection System and safety equipments for the entire Solar Power Plant for 10 Years and cost of the spare is deemed to be included in the quoted rates.18.The firefighting system for the proposed power plant for fire protection shall be consisting of:a) Portable fire extinguishers in the control room for fire caused by electrical short circuitsb) Sand buckets in the control roomc) The installation of Fire Extinguishers should conform to TAC regulations and BIS standards. The fire extinguishers shall be provided for control room housing, PV array installation.19.Solar Components shall not be connected to LAN, WAN, or any Internal Data/OPS nw. 41 20.Sys with Bluetooth, GSM, Wi-Fi, or any Telemetry features should be avoided, unless explicitly cleared monitored.21. Finalization Of Feasibility Report, Design, Engineering, Transportation, Storage, Insurance, Civil Works, Erection, Testing & Commissioning etc., ensuring net-billing as per state net billing policy, quality control of grid connected.22.The Comprehensive Maintenance of SPV Plant would include wear, tear, overhauling, machine breakdown, insurance and replacement of defective modules, Inverters/PCU, spares, consumables & other partsas pe OEM reocmmendation and specification for 5 (Five) years under DLP of Phase-I..23.The Contractor shall arrange technical vetting of the plant during execution by the Cyber/INT officer and training by Unit Technical Pers till defect liability stage of Phase-I. 42 24.a) An energy meter (for net-billing) shall be installed between the solar Grid-tied inverter and the building distribution board to measure gross solar AC energy production (the Solar Generation Meter). The Solar Generation Meter shall be of the same accuracy class as the DISCOM service connection meter or as specified by local regulatory requirements. Separate for two different buildings.b) The bidder must take approval/NOC from the Concerned DISCOM for the connectivity, technical feasibility, and synchronization of SPV plant (if required).c) Contractor shall be provided system software (Cloud) for data hosting of Solar Power Plant with the Government approved agency and also audited by CERT-In (Computer Emergency respose team-India) is deemed to be included in the quoted rates. 25.a) Two sets of Engineering, electrical drawings, and Installation and O&M manuals are to be supplied. Bidders shall provide complete technical datasheets for each equipment giving details of the specifications along with make/makes in their bid along with the basic design of the power plant and power evacuation, synchronization, along with protection equipment is deemed to be included in the quoted rates. 43 b) All test and calibration certificates, wherever applicable.26. The bidder shall take entire responsibility for the electrical safety of the installation(s) and personnel, including connectivity with the grid and follow all the safety rules & regulations applicable as per local guidelines and regulations, etc. Insurance of the installers (of the vendor) working abroad is mandatory.27. (a) The bidder shall take entire responsibility for the electrical safety of the installation(s) and personnel, including connectivity with the grid and follow all the safety rules & regulations applicable as per local guidelines and regulations, etc. Insurance of the installers (of the vendor) working abroad is mandatory.(b) The contractor will carry out fortnightly, monthly, quarterly and annual maintenance as per Proforma of Appendix here-in-after respectively. In case the contractor fails to carry out the above maintenance following penalty per Solar will be imposed. 44 (i) Not carrying out maintenance fortnightly- Rs 2500.00(ii) Not carrying out maintenance Monthly- Rs 5000.00(iii) Not carrying out maintenance quarterly- Rs 7000.00(iv) Not carrying out maintenance annually - Rs 10000.00(c) The Contractor shall be responsible for ensuring production of 800 kW AC output of electricity at the injection point of RMU atleast once in a year from the SPV plant. In case the output is less than 800 kW AC unit, it will be deemed as under-designed plant. The contractor will be responsible for making good the shortfall by repair / replacement of the SPV Plant free of cost. Delay in this regard will attract monetary penalty to be amounted for the period wef very next day of the completion of Phase-I to the date of completion of rectification / replacement by multiplying the maximum value of units less generated than 800 kW AC for every day with the prevailing rate of electricity tariff of WBSEDCL Rate of electricity in West Bengal is Rs 6.52 per unit as in Sep 2025.(d) Maintenance and supervision shall be done by trained men for the safe operation of Solar’s contractor shall carry out fortnightly servicing including adjustment lubrication, repair of replacement fo parts if necessary. In addition to fortnightly servicing contractor’s senior mechanic of foreman shall carryout the inspection as per maintenance schedule and make necessary entries in the proforma attached here-in-after duly signed by Contractor & Engg-in-Charge as applicable kept in the switch room for this purpose. It will be the responsibility of the contractor to see that the maintenance schedule book is maintained properly by their senior mechanic or foreman. They shall promptly attend and call back & shall not be kept pending for more than 4 hours unless it has the prior approval of the Garrison Engineer. 45 (e) For any repairs/ replacement of Solar the contractor shall always be aware of time factor following are the fixed time (including Sunday/Holiday) for repair/replacement of parts/components/ accessories which shall be adhered to :- (i) Minor repair/ replacement- 4 hours (ii) Major repair/ replacement - 1day(f) The decision of the GE regarding Minor/Major repair shall be final conclusive and binding. In case of failure on the part of the contractor to keep the solar’s in running condition within the stipulated period mentioned in above the contractor is to pay penalty charges as mentioned below subject maximum of 10% of the total contract value and after that measurement will not be considered for the same defective Solar till it is in satisfactory working condition :-(i)Upto 12 hours @ 2000/-(ii) Above 12 Hours and up to 24 hours @ 5000/-.28. RFID Tag scanner of reputed make shall be provided by the contractor is deemed to be included in the quoted rates.29. Existing Room at 33 KV Switch Yard shall be used for SCADA/ Solar equipment/Control Room. 46 30. Surface preparation and laying of light yellow/white coloured interlocking tiles of appropriate thickness under the whole area of PV module array to make a reflecting surface for bifacial Solar PV module alongwith periodical water sprinkling arrangement for cooling of interlocking tiles is deemed to be included in the quoted rates. 31.The complete system shall include chemical earthing (as per OEM recommendations) and earth strip/cable etc for earth of SPV module, array, inverter,DC & AC boxes /LA etc as per latest IS/MNRE/IREDA/NISE/SECI/ALMM specifications and guidelines is deemed to be included in the quoted rates. Earth resistance shall not be more than 3 Ohms .32. The mounting steel structure shall be as per IS 2061-1992 and galvanizing as per IS 4759 and should withstand WIND Load as per relevant IS Code/NBC.33.Soil Stabliztion testing certificate needs to be required before completion of physical completion of work (Phase-I) so that the performance of the PV Plant is not affected in Highly Soiled areas for minimum 25 years. 47 34. M&O (Phase-II) should be finalize at the planning stage itself. The important point are as under:- (a) The thermal imaging of pv panel should be taken once a year for checking its health including hot spots.(b) The cleaning cycle of panel should be fixed as per the ratio of short circuit current falling below 0.9. The cleaning provision shoul be made available before evacuating the power.(c) The shutdown duration of inverter should be monitored and recorded and analyzed 48 Supplying, Installation, Testing & Commissioning including design, manufacture and testing at works of indoor type , IP 4X ,floor mounted metal clad, 11 KV VCB panel board totally enclosed & fully interlocked, Horizontal drawout, Horizontal isolation type breaker as per IEC-62271-100/200, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, motor charged and manually/electrically closing breaker suitable for use on 11 KV,3 Phase, 50Hz A.C. supply with STC 25 KA for 3 Sec.Internal Arc for AFLR 25kA at rated voltage for 0.1s at individual compartments i.e. Busbar, VCB and cable compartment.complete with self contained, fully interlocked, rack in and rack out mechanism, air insulated and encapsulated copper bus bars of 800 Amps capacity, breaker featured with mechanical ON/OFF indicator with hand trip device, spring release coil, shunt trip coil and auxiliary switch of 8 NO + 8 NC andequipped with following switch gears and accessories.The panel shall be complete with following switchgear and accessories. The structure of the switchgear must be fabricated using steel sheets coatedwith Alu-Zinc (Aluminium Zinc alloy)/PRINTED CRCA All major sub-components (switchgear, relays, meter & vacuum interrupters) shall be of same make. VCB and vacuum interrupters shall be designed for 100 short circuit operations at full short circuit of 25KA. Breaker shall be roll on floor type/ CASSET TYPE. Separate earthing truck shall be required for each bus earthing & cable earthing. Earthing truck shall be so designed that it is impossible to earth a live. It shall be provided with capacitive voltage divider and complete with audio visual annunciation, one for each panel. Item Continued as 2.01 to 2.04 49 INCOMINGS & Outgoing VCBs :Type : Air insulated VCB, autoreclosing, system voltage :- 11kV + 5%, 50 Hz+ 5%, 3 phase, rated voltage : 12kV, rated current : 800A in 40 ° C ambient, Short time rating for 3 sec : 26.3 kA, Short Circuit Making Current : 65 kA, insulation level (PF rms/ impulse peak) : 35 kA/75kA, System Ground : Solidly Earthed,Duty Cycle : 0 - 0.3 sec - CO - 3 min - CO, Break/ Make time :- Not more than 5 Cycle, Range for Auxiliary voltage for Closing / Tripping / Spring Charging : 85-110%/ 70-110%/85-110%. of rated voltage. The VCB must withstand 10000 mechanical, & 100 at rated short circuit current. The breakers should have auxiliary contact 6 No+ 6 NC, in minimum. The used Breakers will comply with IEC 62271/ IS 13118. Qty. - 3 Nos (1 no Incomer & 1 outgoings)Busbar: Rated Current : 800A @ 40°C ambient, Material : Silver Plated /Tined , High conductivity elecrolytic Copper Bus Bar sleeve :Heat Shrinkable PVC Sleeve with joints having full voltage soft PVC shroude Short time rating for 1sec :26.3kA -1 setCurrent Transformer:Voltage class: As specified in Circuit breaker ; Type: cast resin type, Dual core, Dual Ratio , Barden :10VA; Class insulation : Class E or better . Protection core: 5P10, Metering : 1.0 , Short time rating for 1 sec :26.3kA Ratio :300-150/1-1, 7 setsBus Potential Transformer: Rated Voltage : Primary - 11000 / ✓3 , Sec -110✓3; Type : Cast resin , draw out type, 3- phase , 3-limb complete with HV fuses . Barden : 100VA per phase ; Class of insulation : Class F or Better , Accuracy Class: 1.0;Rated Voltage factor : 1.2 continuous, 1.5 for 30 Secs. PT shouldbe drawnout type and serivce continuously shall be indepandent of Breaker trolly position...1set 50 Relay for Control & Protection: Numerical Type IDMT Relay (50/51, 50N/5IN) with two elements for overcurrent and earth fault having settings 50% to 200% for overcurrent and 20% to 80% for earth fault in equal steps with time and current settings and high set instantaneous unit. Additionally, condition monitoring CB wear, condition monitoring CT supervision, disturbance recorder, undervoltage & over voltage protection, trip circuit supervisioncan be measured through the relay. The device shall support webserver/web HMI through which we can monitor and control the relays over a ethernet Lan network. Licenses for theprogramming software shall be provided free of cost.The numerical relay shall have large mimic-based LCD screen display . .The relay shall have 8 Digital inputs and 8 Digital Outputs and one additional watchdog ouput.The device has to aloe controlling of min. six objects (circuit breakers, disconnectors and grounding switches). Controlling has to be done by “select-execute” or “direct control” principle. Controlling has to be possible by: through local HMI, remote communication, via digital input or via function key. Events has to be readable to SCADA systems, front panel or by setting software.The sample rate of the recording has to settable to 32samples/cycle.The devices shall provide storage up to events 2000 based on the resolution.The device shall support following communication protocols: Native IEC 61850 ed1 & ed2, Modbus TCP. The IEC 61850 communication has to support peer to peer communication (GOOSE) if requiredThe IEC 61850 interface must be able to configure through setting software. Also the same setting software has to be able to generate ICD filesThe device shall have KEMA IEC61850 edition 2 certificates - 3 sets. High Speed Master Trip relay VAX31- 3 Set, Ttrip circuit supervision relay-VAJH13-3 set6 Window Annunciation Facia . with ACCEPT, RESET & TEST Push Button - 3 set . Auxillary relay for Transmission faults (VAA33)- - 3 Set 51 Metering: Meters: 1-NosUL&CE Multifunction Digital meter displaying Voltage, Amps, kWh, kW, P.F., Active, reactive, apparent energy , disturbance direction detection, Individual harmonic up to the 63rd harmonic. at least 256 samples/cyclewith ethernet Port with inbuilt webserver and complying to IEC 61557-12, IEC 62053-22 certified by third party laboratory.Temperature Monitoring Sensor for the Three Phases of Incomer VCB Panel :Supply, installation, testing & commissioning ofthermal monitoring system to be provided to detect abnormal temperatures due to faulty connections and to prevent equipment B19damage. The switchgear shall have wireless temperature measurement sensors at all critical points:(a) 3 nos. foreach phase at incoming side cable joints The wireless temperature sensors installed on conductors shall be :(i) Installed with direct contact to hot point, to achieve accuracy of +/- 2°C(ii) Self-power (no auxiliary supply, no battery)(a) communicate wirelessly(c) Operate from -25°C to 125 °CThe system shall allow 2 configurable thresholds (pre-alarm and alarm). This system shall have integrated algorithms enabling to anticipate as early as possible an abnormal temperature, before damage occur (strong predictive capacity) and generate alarm through SCADA/monitoring software. Thermal sensor shall beself powered by the network current. Temperature data is sent via Zigbee wireless communication to provide high performance and accurate thermal monitoring. The sensor is secured to the connection point and is in direct contact with the measured point. Smartphones or tablets (with a Zigbee communication dongle) can be used with our Thermal Connect mobile application to scan data locally and can replace the need of periodic infrared scanning. Thermal sensors should comply to following standards:1 EN/IEC 61010,2010 2. UL 61010-12, 20123. ETSI EN 300238, 2012 V1.0.1 4. IEEE 802.15.4, 2013 52 Power Pack shall be with 220Volt AC Input & 24 volt DC continuous output suitable for closing /tripping indication of HT panel boards with 2nos 12Volt 100AH maintenance free batteries, chatging unit for trip system complete with suitable capacity dogital MFM connections with 2.5sq mm FRLS inaulated copper conductor cable etc as required.-4 set.The 11 KV HT Switchboard of 1 panel,shall bewith all accessories, interconnections,internal wiring, labels, space heaters etc. complete as required.3 panels shall be mechanically interlocked in such a way that only one operates at a time and multifunctional digital meters shall be interconnected and programmed in such a way that total consumption will come in one meter summating both of them.Note: 1. Quotated rates shall be inclusive of construction of foundation for the installation of VCB as per OEM drawing.2. The equipment shall be tested by SEI post sucessful installtion and report shall be submitted to this office. 53 Design, Manufacturing, Supply, Installation, Testing and Commissioning of 3 way 12 kV rated Ring Main Unit ofwith Fault Level 21KA 3 sec internal ARC 1 sec for tank and cable box , consisiting of 630A12 kV rated , 2 nos motorized type VCB as incomers & 1 load break switch as outgoings with metering modules along with necessary Earth Switches,battery and battery charger for shunt trip arrangement andMotor and other auxiliary circuit operation, HT CopperBus bar with current density not more than 1.6A/sq. mm as per detailed description as follows: RMU Construction: The switchgear and busbar shall all be contained in a stainless steel enclosure filled with SF6 at 0.3 bar (300 hPa) relative pressure to ensure the insulation and breaking functions. Sealed for life, the enclosure shall meet the sealed pressure system criterion in accordance with the IEC 62271-1 standard (§ 3.6.5.4): a volume for which no further gas processing is required during its entire expected life”. In addition, manufacturer shall confirm that maximum leakage rate is lower than 0,1 % / year. It shall provide full insulation, making the switchgear insensitive to the environment (temporary flooding, high humidity...), IP67 degrees of protection in accordance with recommendation IEC 60529 § 14.2.7. No SF6 gas handling required at site. Thus assembled, the active parts of the switchgear shall be maintenance-free and the switchboard shall be low-maintenance. The switchgear operating mechanism shall have an IP2X protection and cable chamber shall be IP55, Over all IP protection shall be IP55 . The tank shall be made of at least 2mm unpainted stainless steel. Item Continued as 3.01 to 3.05 54 VCB is the preferred dielectric medium for MV RMUs. Oil filled switchgear will not be considered. RMU shall be in accordance with IEC 60376.Any accidental overpressure inside the sealed chamber will be limited by the opening of a pressure limiting device in the lower part of the enclosure. Gas will be released to the rear or the bottom of the switchboard away from the operator and internal arc tested for both cable and tank for 21KA 1sec AFLR with test conducted with minimum 3 functions TankNumber of mechanical operations of Circuit breaker 2000 O/C , Number of electrical operations at full loop current for LBS: 100 O/C , Number of electrical operations at full loop current for CB: 2000 O/C,. Manufacturer shall provide type test report to prove compliance with IEC 62271-200 Annex A, Internal arc classification class AFL with 21kA 1s for the enclosure. Make of the RMU, vaccum intrtupter , relay & meter shall be of same OEM. All the test certificate shall be in the name of the OEM only . If there is any name change / acquisition by other OEM happened for the RMU then test cerificates shall contain the new OEM name only.HT System : 3 phase -3 wire , HT Fault level21 kA, Power System earthing - solindly earthed at up stream source, HT Copper Bus with Short Time Curent rating 21 kA for 1 Sec ( 3Sec), Continuous current rating at least 630 A. tank and cable chamberof RMU must be IAC rated for 21 kA for 1 Sec AFLR. Design ambient to be considered as 40 Deg C.HT Circuit Breaker :(i) There shall be 1nos.load break switches as incomings and 2 nos 12 kV rated VCBas outgoing ( total 3 nos.) . The circuit breakers shall be fixed type. All of the switchgear shall be capable of withstanding this current without any damage being caused, in accordance with the recommendations IEC 62271-1 and IEC 62271-200.Loss of service continuity class: LSC2(ii) The Circuit Breaker must be rated for 12 kV ( nominal Voltage), 28 kV/75 kVp ,3 Phase, 50 Hz, Short Circuit Fault Level of 21 kA for 3 sec. 55 (iii) No. Of Close Coils - 01 no. operable at 24 V DC (85% - 110%)/ Spring Assited Closing, No. of Trip Coils - 01 nos. ,operabale at 24 V DC ( 70% - 110%) for shunt trip.(iv) Provision for supervision of the shunt Trip Circuits for the Trip Coils to be provided. (v)Switchgear classification: PM class(vi) Loss of service continuity class: LSC2(vii) Duty Cycle : O – 3min – CO – 3min – CO, Vacuum Circuit breaker shall be of M1, E2, C1 duty and capable for minimum 50 short circuit breaking operation at full short circuit level.(viii) STC rating 21 kA for 3 Sec (for Vacuum Interrupter).(ix)Vacuum Interruptor must be hermetically sealed and must comply IEC 60056 ( along with latest amendments). Vaccum interrupter shall be of same make as RMU(x)Circuit Breaker to be equipped with Suitable tripping arrangement with push button, Mechanical counter to assess the total number of operations of the breaker, Mechanical ON / OFF indicator, Auxiliary switches, Auxiliary Contacts( at least 2 NO + 2 NC of Class 2 category), Emergency trip push button.(xi) The Operating mechanism shall be spring charged motor operated/ spring assisted as per OEM type tested design type with Spring Charge Universal motor operable on 24 V DC / 230 V AC.(xii)Suitable monitoring of Bircuit Breaker status ( ON, OFF, Trip, CB Spring charged if applicable), Trip Circuit Healthy / Unhealthy, DC healthy/unhealthyto be provided using (xiii) Voltage Presence Indicator shall be provided against each HT circuit ( against each VCB) on line side for knowing the presence of line enerzisation status.(xiv)Number of Mechanical operations at full rated current for breaker: 2000 O/C 56 HT CT /PT : Load Break Switch - 11 KV, 630A, 21KA for 3sec Motorized Load break switch; with built in line side manual earth switch. Earthing should be completed within 2 operations only(i.e 1. Main switch - OFF, 2. Earth switch - ON). LBS shall have 3 positions, open or disconnected, closed and earthed, and will be constructed in such a way that interlocking prevents unauthorized operations. For earth switch, manual opening and closing will be driven by a fast-acting /snap action mechanism, independent of operator action. LBS and earth switch shall have a min of 1000 (M1) mechanical operations ,and 5 nos closing operations at rated SC current. LBS should have 100 electrical operations at rated current. LBS & Earth Switch should have separate apertures for operation.i) One set of 03 nos. ( for 3 phases) dual core Cast Resin CTs for Eachincomer VCBcomplying with IEC:60185 & IS 2705 ( along with latest amendments) , Core -1 - 400-200/1 A , 2.5 VA, Cl 0.5 for metering ; Core-2 - 400-200/1 A, 2.5 VA , 5P10 for Protection.ii) 01 no. of 03 phase Dual Core PT forHT bus ( 11 kV)with protection HRC fuseCore 1- 11kV /√3 / 110V/√3, Cl 0.5s, 50VACore 2- 11kV /√3 / 110V/3, Cl 3P, 50VA(iii) Multifunction Meter:2 Nos. 3 phaseDigital Multifunction Meter6400NGwith Voltage, Amps, kWh, kW, P.F., Active, reactive, apparent energy , disturbance direction detection, Individual harmonic up to the 63rd harmonic. at least 256 samples/cyclewith ethernet Port with inbuilt webserver and complying to IEC 61557-12, IEC 62053-22 certified by third party laboratory.for each VCB panel ( 96 mm x 96 mm) , Flush mounted, Class 1 conforming to IEC 62053-22 ( along with latest amendments). 57 Protection Relay: (i) 2 Nos. of Numerical Type Self-powered IDMT Relay(50/51, 50N/5IN) with two elements for overcurrent and earth fault having settings 50% to 200% for overcurrent and 20% to 80% for earth fault in equal steps with time and current settings and high set instantaneous unit. Relay should communicate on Modbus RS-485.(ii) Each VCB must have separate Anti Pumping Relay / Antipumping feature through motorization circuit.Fault Passageindicator: The FPI shall facilitate quick detection of faulty section of line. The fault indication may be on the basis of monitoring fault current flow through the device. The FPI should be self-powered and should have internal lithium battery for external indication and setting of FPI in the absence of current.The FPIs shall include: Fault detection - Phase to phase and Phase to earth faults.One potential- free output contacts for hardwiring to RTUs. On this basis, the SCADA/DMS will be able to monitor phase / earth fault condition.Local fault indications - LCD display on FPI front panel along with LED indication on front panel of RMU enclosure.Multiple reset option : End of time delay (Adjustable from 2 to 16 Hrs)Remote reset (Via potential free input contact of FPI)Manual reset (Reset button on front panel of FPI)Automatic reset on current restoration.The characteristics of the FPIs shall include: Phase fault thresholds configurable from at least 100 to 800 A,Earth fault thresholds configurable from at least 20 to 200 AMultiple number of steps for adjusting phase and earth fault thresholds. Fault current duration range configurable from at least 40 ms to 100 ms in 20 ms steps and further 100 ms to 300 ms in 50 ms steps. Variations with respect to these characteristics may be acceptable as long as they prove applicable and provide the same or better flexibility. 58 EARTHING : The cables shall be earthed by an earthing switch with short-circuit making capacity, in compliance with IEC 62271-102 standard. The earthing switch can only be operated when the switch is open. The switch and earthing switch operating mechanism shall have a mechanical endurance of at least 1000 operations. Integrated line side Earth switches shall be provided in each HT Circuit. ( against each VCB)RMU Bushing & Cable Termination: It is preferable to have all bushings accessible from the front of the RMU. Bushings along the sides or the rear of the RMU are not acceptable.For each cable compartment, the bushing shall be at the same height in order to facilitate a possible reversal of the cables. The bushing should be conveniently located for working with cables specified and allow for the termination of these cables: - 630 A M16 bolted connectors for switch-disconnectors and vacuum circuit breakers functions.The profiles of the cable connection bushings shall be in compliance with IEC-60137 standard. Cable clamps:A cable clamp arrangement must be provided for all network cables terminated on the RMU.Provision for Cable Entry: There shall be suitable provsion for Cable entry from bottom through 3 mm thick CRCA steel thick detachable gland plate along with provision for termination of 2 runs of 3 c X 300 Sq mm 11 kV (E ) , XLPE insulated Aluminium Cables (for HT side) and at LT side runs of cables matching with outgoing MCCB current rating.Note: (i) Quotated rates shall be inclusive of foundation for the installation of VCB as per OEM drawing.(ii) The equipment shall be tested by SEIaftersuccessful installtion and report shall be submitted to this office and cost deemed to inclusive in qoated rates 59 M&L for water proof, 3 core PVC insulated and PVC sheathed, copper conductor cable of size 1.5 sqmm, 1100 Volts grade including PVC conduits properly fixed on steel poles using GI wire for electrical connection of street light fittings, complete all as specified and directed. 60 Supply and fixing junction box having protection dust proof, acid resistant, shock proof, fire retardent self extinguisher for outside installation with knockout entry for cable of size 10 - 25 sqmm andminimum size 295x195x95 mm with terminals, with and includingbrackets for street light pole mounting andone 6A MCB SP complete all as specified and directed. 61 M&L for Advanceencapsulated compound based Chemical earthing CPRI tesed maintenance free , pipein -pipe technology upgraded(Zinc & Alloy coated). , Zinc & Alloy coated (80 -100) microns with pure zinc (99.9%) & Alloy coating (200-250) microns. Earthing system conforming IS 3034. The outer and inner pipe should be 76.2 mm and 41.9 mm dia respectively of3 mtrs long zinc coated with additional special alloy coating 300 mm on top side for additional protection of the terminal . The annular space between the pipes to be filled up with Compactfill (CF) (Crystalline Conductive) mixture which should bemachine pressed in the pipes not disintegrate or collapse when outer pipe corrodes . The inner pipe should be extended with terminals for connectivity.The job includes digging the pitsin any type of hard densesoilof min size 1000 X 1000 X 3050 mm depth taking out excavated soil, lowering/ placing thethe pipe in pipe earth electrode in pit in center ,filling of pure conductolite back filling compound (BFC Conductolite) having excellent moisture retaining capacity in 300 mm around the electrode(minimum 4 bags of 25 KG per pit per unit) or more qty of backfillcompoundas required to fill around the the elctrode in 300 mmin circumfrance of electrode . Contractor has to fill the remaining portion of pit withlow resistivity soil (agriculture soil) free from stones etcs, to be bring from out side defence landas the soil resistivity ofStn is very high and mixed with min 3 Bags of 50 Kg each of Bantonide clay. The BFC should be eco friendly it should not contain envernmently hazardous material/metal having ROHS certification from NABL accredited lab.The earth pit should be provided with a FRP earth pit cover for protection and safe guard of terminals. The material of earth electrodeshould have good electrical conductivity & anti corrosion property in wide range of soil conditions. The job also include M & L for in PCC(1:3:6) typeC-1 around the FRP cover for support and foundation and colouring the PCC work withdesired colour.completeall as specified and directed. Item Continued as 6.01 62 Note : (i) Design of earth electrode should be of pipein-pipetechnology .(ii) Contractor have to submit literature of earth electrode and get the make approved of GE before procurement.(iii) The earth electrode shall be CPRI tested to withstand short current test for 60kA rms for 1.0 second and 150kA for peak current.(iv) Contarctor has to fill pure back fill compound conductolite all around the earth electrodein 300 mm bore up to full depth of bore.(v) Contractor shall refill the pit with low resistivity soil (agriculature soil ) free fron stone etc and mixed with 06 bags of Bentonite of 25 Kg each to achive the low resistance values. (vi) copper strip will be laid below 60 cm from ground level and connected to test point through plinth protection. This Earthing System used for VCB and RMU only. For Solar Power Plant Earthing System is already deemed to be included in quoted rates.(vii) Necessary cost of repair to plinth protection and connected plate and earth continuity conductor by providing 2 x brass nuts bolts and brazing of joints,bringing argiculture soil from out side defence land and cost of 6 x Bags of bentonidedeemed to be included in the item rate.(viii) Contractor has to clear the side and disposed off the excavated soil from pit on completion of work. 63 SAFETY EQUIPMENTSSupply and fixing Rubber hand gloves suitable for 11 KVas per OEM recommendationcomplete all as specified and directed. 64 S&F for glass framed Shock treatment chart both in Hindi & Englishand connected accessoriescomplete all as specified and directed. 65 S&F for dry powder chemical type 4.5 kg fire extinguiser with clamps and connectedaccessories ISI Marked complete all as specified and directed. 66 S&F for single line diagram, schematic diagrams etc. of A1 size on suitable Aluminium sheet including lamination etc. as required as per OEM recommendationcomplete all as specified and directed. 67 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed. 68 Excavation in trenches, not exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundation, manholes, laying of UG cables/pipes etc. not exceeding 10 Sq.m on plan and getting out in soft/loose or any type of soil complete all as specified and directed. 69 Removing excavated material (soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed. 70 Returning filling in, soft/looseor any type of soil including spreading leveling watering and ramming complete all as specified and directed. 71 Excavation in post holes (or similar holes) in soft/loose soil each n.exc 0.50 cum, getting out,returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface all as specified & as directed. 72 M&L for RCC M-20, design mix (using 20mm graded crushed stone aggregate), including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 73 M&L for steel tubular swaged poles complete with cast iron base plate, finial taper plugs, bolts, nuts & screws as specified type 410 SP-31, 9.0 meter longinclusive of two coats of aluminium paint over one primer coat of red oxide zinc chrome primer including preparation of surfaces complete all as specified and directed.NOTE : (a) The poles shall confirm to IS - 2713 & each component pipe shall be ISI Marked & confirm to IS - 1161. (b) Necessary earthwork, PCC etc. shall be measured & paid separately under relevant items of work. 74 S & F LED Street lights nominal power 90 Watt, LED of Make Osram; Bridgelux ; Philips; Nicha; Cree; Samsung, LED wattage of minimum 3 watt each and Maximum 5 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 120 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with polyester powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hourswith IK10 and L70 on including fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed.(i) If connection.cable from pole Juction box to street light and street light bracket up to 2 mtrs be included and measured in unit rate item, Beyond 2 mtrs of length to be paid seperately under respective items.(ii)At location where street lights/flood light are connected through overhead conductor, connection cable from light fitting to overhead conductor is deemed to be incl in the item rate. (iii) All LED street light/flood lights shall be properly connected with earth dolly provided with fittings and steel poles earth bolt.(iv)All LED lights have replacement warranty of 5 years from the date of completion of the contract accordingly condition 46 of GCC (IAFW-2249) shall be amended to extent mention above. Contractor has to submittwarranty certificate from manufacturer . Payment of light fitting will be released after receipt of 3 year replacement warranty certificate from manufacturer.(v) The LED lights will replaced bythe contractor free of cost in the case of manufacturing defects and Failure due to electrical impact if not connected properly with earth. Hence it is contractor responsibility to connect the light fitting earth wire and shall be grounded properly.(vi) The contractor shall submit the surge protection certificate and Type test certificate LM 79, LM 80 for luminaries from LED manufactutre. 75 M&L for Cement concrete (1:4:8) type D2, (Using 40mm graded crushed stone aggregate) as in foundations of poles and stay, filling and mass concrete complete all as specified and directed. 76 M&L for plain cement concrete (1:3:6), type-C2 (40mm graded crushed stone aggregate) as in foundation, filling and mass-concrete, coping etc for pole foundationwith and including necessary formwork complete all as specified and directed. 77 M&L PCC (1:2:4) type B2 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete and copingwith and including necessary formwork complete all as specified and directed. 78 Material & labour for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick burried directly in ground (Earth pit not less than 4 mtr deep below ground level) with top edge of the plate not less than 3.25 mtrbelow ground level connected to copper strip 20 x 3.15 mm as earth lead by brass nut bolts washer including brazing the copper strip with copper plate as shown in electrical plate No 3 connected to earth test point including necessary excavation for earth pitin hard dense soil, rocky / disintergate rock, filling charcoal and salt around the plate in layers , filling the pit with low resistivity agriculture soil free from stones, to be bring from out side defence land and mixed with Bentonite , (4 bags of 25 Kg each ), construction ofinspection pit ( earth pit chamber) of brick work of size 600 x 600 x 600 mmwith PCC copping of 1 :1.5: 3, 12.5 mm aggregate A1 with MS sheet 2.8 mm plate cover on frame ofangle iron of size 40 x 40 x 5 mm with , wire mess, funnel, test point, 40 mm dia GI protection pipelightgrade and20 mm GI peforated pipefor wateringetc complete and testing on completion. The electrode and lead shall be of copper all as specified and directed by Engr-in-charge (Copper strip upto 7.5 RM will be included in the item rate and copper strip beyond 7.5 RM will be measured seperately Item Continued as 22.01 79 NOTE :-(i) Contractor shall uselow reisistivity fresh agriculture soil , mixed with 4 x Bags of bentoniteclay of 25 Kg each for refillingthe pit to achive the desired resistance.(ii) copper strip will be laid below 60 cm from ground level and connected to test point through plinth protection(iii) Necessary cost of repair to plinth protection as per existing specification and connected plate and earth continuity conductor by providing 2 x brass nuts bolts and brazing of joints,bringing argiculture soil from out side defence land and cost of 3 x Bags of bentonitedeemed to be included in the item rate.(iv) Contractor has to clear the side and disposed off the excavated soil from pit on completion of work.(v) Contractor has to submit test report of earthing after completing the earthing.(vi) Bentonite clay should be Conf to IS 6186: 1986.(vii) The cost ofCopper strip of size 20X3.15 mm from top of earth plate upto 7.5 meter above ground level is deemed to be included in the unit rate of above item.and copper strip beyond 7.5 RM will be measured seperately.(viii). All the joints in copper strip and connection with Earth Plate to be welded through brazing and in addition by proving brass nut bolt and washer are deemed to be included in the unit rate. (ix) Cost of brazing / welding and nut bolts are deemed to be included in the unit rate. (x) Cost includes removal of excavated soil upto a distance of 100 mtrs. 80 Supply and fixing copper strip of size 20 x 3.15mm as earth continuity conductor or main earthing lead fixed on V typeporcelain insulator, 4 BM, heavy duty ( ceramic bus bar supportinsulator off whitecolour ofsuitable for mounting strip of 20 mm wide x 3.15 min thick) saddle to wall, buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 20 x 3.15 mm copper strip brazingto each joints and connected with by providingbrassnut boltsand washer including test point all as specified and directed by Engr in Charge. Note : Insulators shall be provided on every 50 cm. (Minimum 2 x insulators to be provided in every 1 x metre of strip and rate of the same deemed to included in quoated rates) 81 M&L sand cushioning (dry) in trenches for protection of UG cables (below, above and around the cable laid in trenches) of 230mm spreding thickness and consolidated (punned) upto 180mm thickness, complete all as specified and directed. 82 Supplying and laying un-reinforced precast concrete cable cover, class HV, type 1 with peak, size 300mm x 180mm x 40mm complete all as specified and as directed. 83 M&L for GI pipe 100 mm bore, light grade with all fittings and fixtures (ISI Marked), laid in trenches, under road or fixing on wall/ pole /crossing drain /nallah etc. of bore complete all as specified and directed. 84 Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc.with all fixing & connecting accessories complete all as specified and directed. 85 Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 4 core ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc.with all fixing & connecting accessories complete all as specified and directed. 86 Supply, laying, jointing & testing XLPE insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core ISI marked as per IS 7098(Part-I): 1988 including cable glands, lugs etc. to suit the cable size and to be laid in trenches, fixed along pole, under floors, through GI pipe laid under floors/roads, through concealed GI pipe along wall etc.with all fixing & connecting accessories complete all as specified and directed. 87 Supply, laying & testing PP-R IS-15801 (Polypropylene random co-polymer) pipe 3-layer 63 mm dia (outer green coloured UV stablilized, middle black coloured UV stabilized and innermost layer white coloured with anti-microbial property) fusion welded grade PN-10 SDR-11 ( Pressure nominal 10KGS/cm2 ) having thermal stability for hot & cold water supply including all types of plain and brss threaded PPR fittings of any size such as elbow, tees, FTA and MTA etc laid in trenches complete all as specified and as directed.Note:The contractor shall submit 15 Years warranty certificate against leakageand defect liabilty period deemed to amended acordingly. 88 Supply, laying & testing PP-R IS-15801 (Polypropylene random co-polymer) pipe 3-layer 32 mm dia (outer green coloured UV stablilized, middle black coloured UV stabilized and innermost layer white coloured with anti-microbial property) fusion welded grade PN-10 SDR-11 ( Pressure nominal 10KGS/cm2 ) having thermal stability for hot & cold water supply including all types of plain and brss threaded PPR fittings of any size such as elbow, tees, FTA and MTA etc laid in trenches complete all as specified and as directed.Note:The contractor shall submit 15 Years warranty certificate against leakageand defect liabilty period deemed to amended acordingly. 89 S&F for 63mm (OD) PP-R Gate valves (brass insert)and connected acessories complete all as specified and as directed. 90 S&F for 32mm (OD) PP-R Gate valves (brass insert) nd connected acessories complete all as specified and as directed. 91 M&L for hard core of gauge not exceeding 63mm with broken stone or boulders, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed. 92 Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M35 grade conforming to IS 15658-2006 made by block making machine with strong vibratory compaction, of approved size, design & shape, cast in rubber mould, glossy finish of approved colour, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. 93 S&F for RCC pipes of 600 mm dia, NP-2 laid and jointed complete with collars complete all as specified and directed. 94 S&F for 250mm bore Flue pipes of mild steel sheet, black, in suitable lengths as approved by GE and fixed to walls complete all as specified and directed. 95 M&L for Brickwork with fly ash bricks (modular bricks ), straight or curved on plan exc 6m mean radius, built in cement mortar(1:6) complete all as specified and directed. 96 Material and labour for plastering 15 mm thick (in two coats of 10 mm and 5 mm thick) on fair faces of brick work or concrete surfaces (on vertical surfaces) in cement mortar 1:4 with integral water proofing compound finished even and fair complete all as specified and as directed. Note: - Water proofing compound will be deemed to included in qoated rates. 97 M&L for applying three coats of white wash on newly plastered wall surfaces including preparation of surface complete all as specified and directed. 98 S & F hot rolled low tensile structural steel of grade E165 as per IS 15911: 2010 as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar works complete all as specified and as directed. 99 S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge. 100 S&F flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 101 S&F MS screw bolt (machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc. 5 cm and n. exc 10 cm long, diameter of neck 5 to 10 mm complete all as specified and directed. 102 Supply and fixinggalvanized steel chain link fence fabric of mesh size as approved , made out of 4 mm nominal dia of mesh wireconforming to IS 2712-2003 and having zinc coating of type heavy as laid down in IS-4826 including line wires/ binding complete all as specified and as directed(A Board of Officers under the orders of GE shall be convened to ascertain the weight per square metre of galvanized steel wire chain link fencing brought at site by the contractor against each lot of materials). 103 S&F 10mm round bars Fe-410-W (Gde-250) quality-A or Fe-290-(Gde-E-165) as in stiffner to hold the chain link fencing fixed with angle iron post inclucinding necessary welding and fixing arrangement at ends complete all as specified and directed . 104 S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steelpins, etc. complete all as specified and directed . 105 Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed. 106 Material and Labour for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel and iron surface not exceeding 10 cm in width or girth including preparation of surfaces complete all as specified and directed. 107 Materials and Labour for reinforced cement concrete M-20design mixin columns; pillars; piers; posts; struts etc,complete all as specified and directed. 108 S&F for Mild steel TMT bars 10mm dia and over, conforming to Fe 500 D, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed. 109 S & F for mild steel TMT bars 6 to 8 mm dia, conforming to Fe 500 D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, stirup,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 110 M&L for construction of valve chamber with MS sheet cover 3mm thick with angle iron) frame of size 50 x 50 x 6mm and locking arrangements including painting one coat of primer followed by two coats of black sysnthetic paint including excvation and earth work in any type of soil,PCC (1:4:8) type D2 in foundation ,PCC benching 1:2;4 type B-1 ,PCC (1:5:8) block masonry 20 cm thick in cement mortor (1:6),10 mm thick plastering in CM 1:4 ,PCC bed in (1:3:6) and coping 50mm hick in cement concrete 1:2:4 type B1 using 20mm stone aggregate including necessary formwork,paintin one coat of red oxide and two coats of bituminious black paint on all steel surfaces as specified and as directed of sizes 800mm x 800mm x800mm (internnal dimensions) complete all as specified and as directed. 111 Sch A Part-II (Phase-II) 112 Providing Services for Manning and Operation of Solar Power Plant 0.8 MWp near 33 KV receiving stationat Sevoke Mil Station for FIRST YEAR after completion of Ph-I of the subject work with oneskilledcategory Electricianhaving certificate of Surya Mitra from NISE) for twoshifts of 8 hour, one helper (semi-skilled category) in two shift of 8 hrs eachcontinuous operation (including Sunday/Holiday) to maintain sub station in/out side Panels, Invertor, DC junction box, VCB as specified, including daily and weekly check up including cleaning of PV modules complete with suitable cleaning cloths etc , upkeeping the installation operational and in health condition, having own conveyance and communication system like mobile etc. complete, for Solar Power Plant with all minor consumable and expendable items and labour and tools for smooth and efficient operation complete all as specified and directed by Engineer-in-Charge. Make of spare parts / equipments of the Solar Power Plant :- Same as installed in the preceding phase of the work.Repair or replacement ofdefective components or spare parts will be carried out free of cost under DLP and comprehensive Maintenance as per OEM recommendation up to DLP period included in BOQ item No. 1.00. The Contractor may submit his claim for every months on pro-rata basis subject to condition 64 of IAFW-2249 (General Conditions of Contracts)The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 17,92,949.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. Item Continued as 56.02 to 56.06 113 NOTES :- In addition to and Manning, Operation and Maintenance of Solar Power Plant, the following works will also be carried out by deputing addl manpower where required, to the entire satisfaction of Engr-in-Charge.(a) Minor repairs and preventive maintenance required to ensure serviceability and efficiency of complete MRS complex including supply of HT 11 KV fuse wire of proper sizeand minor spares such as nut, bolts, spring, lock nut of VCB/OCB as per sample, broom, duster, grass cutting tools, phawara, pick axes for cleaning/grass cutting of complete at Sub Stn Complex. 114 (b) Record of activities such as voltage / current / PF / Energy consumed / temp of transformers, break downs, day to day maintenance of Solar PV Plant etc.(c) The contractor shall ensure that all safety precautions are strictly exercised by the staff employed by him.Adherance to IE rules and statutory rules in vogue must be ensured.The contractor shall be fully responsible for any mishap that occurs due to any fault of the employee or due to non adherance of safety norms.(d) Record of activities such as attendance register, duty roster, pay distribution register of the whole staff employed by the contractor.(e) The electrician staff employed by the contractor shall be ITI holder with four years experience. 115 (g) Security lights within the complex will be operate by the tenderer. (h) The under mentioned tool kitwill be provided at site with person on duty :-(i) Electrician tool kit such as screw driver set, tester, test lamp, cutting plier, insulation tape, fuse wire of required size. (ii) Tongue tester(iii) HT megger(iv) First aid box (v) Shock treatment chart duly framed(vi) 33 and 11 KV Hand gloves(vii) 33 KV discharge rod withcopper chain(viii)) Helmet -02 nos(ix) Suitable Footwear - 02 nos(x) Cotton protective clothing with long sleeves duly embossed with GE Sevoke as directed. The tenderersquoted rates shall be deemed to be include the cost of all above provisions and nothing extra will be paid on any account. 116 (xi) The Bidders shall abide by the latest Labour rules and minimum wages Act. Wagespaid by the bidders to the persons employed shall not be less than the minimum wages fixed by the state/central government from time to time whichever is higher. (xii) The Bidders is responsible for insurance, EPF, ESI, Bonus, Labour welfare cess et., as applicable and shall be paid to the workmen as per existing Labour rules/ Acts/ regulations and rate quoted shall be deemed to be included for the same.(xiii) Dress Code : The bidders shall provide the workmen with Dark Blue Colour uniform {formal pant & T-shirt} with labels showing/ printed i.e. Name of the firm and designation on front and on the back of the T-shirt along with protective clothing, Industrial safety shoes, protective gears like helmet, safety belt etc..(xiv) Supervision and attending of all incoming & outgoing Solar Power Plant equipment metering equipments & monitoring to loads & other parameters of incomming & outgoing feeders & maintaining log sheet and attendance sheet. 117 INSURANCE: The Bidders shall also insure the workmen employed on the job.The Bidders shall be responsible for all Accidents/Injuries happening to the workmen. Any accident causing minor/fatal injury, partial disability due to any untoward incident or non-adherence to safety and IE regulations or fault in maintaining of internal electric supply system or on account of any mishandling/ wrong operation/ lack of knowledge of safety precautions or on account of any circumstances beyond his/ their control, the bidders shall be solely responsible for settling all claims of compensation to the deceased, falling which department will have a right to recover any sum indicated/ claimed by Labour commissioner/court authorities. No claim whatsoever will be entertained in this regard. No compensation is payable by the department on this account. Bidders shall provide first aid boxes to meet any emergency situations. 118 All as perBOQ serial item No 56.01 to 56.06 as mentioned here-in-before but for SECOND YEAR after completion of Ph-I of the subject work .NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 18,75,076.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 119 All as perBOQ serial item No 56.01 to 56.06 as mentioned here-in-before but for THIRD YEAR after completion of Ph-I of the subject work .NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 19,61,175.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 120 All as perBOQ serial item No 56.01 to 56.06 as mentioned here-in-before but for FOURTH YEAR after completion of Ph-I of the subject work .NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 20,51,671.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 121 All as perBOQ serial item No 56.01 to 56.06 as mentioned here-in-before but for FIFTHYEAR after completion of Ph-I of the subject work .NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 21,46,848.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 122 All as per BOQ serial item No 56.01 to 56.06 as mentioned here in before but for SIXTH YEAR after completion of Ph-I of the subject work .NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 22,46,564.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 123 All as per BOQ serial item No 56.01 to 56.06 as mentioned here in before but for Seventh YEAR after completion of Ph-I.NOTE :- (a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 23,51,386.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 124 All as per BOQ serial item No 56.01 to 56.06 as mentioned here in before but forEight YEAR after completion of Ph-I.NOTE :-(a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 24,61,315.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 125 All as per BOQ serial item No 56.01 to 56.06 as mentioned here in before but for Ninth YEAR after completion of Ph-I.NOTE :-(a)The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 25,76,917.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 126 All as per BOQ serial item No 56.01 to 56.06 as mentioned here in before but for TENTH YEAR after completion of Ph-I.NOTE :-(a) The bidders shall ensure that the quoted amount for O&M is not less than minimum fair wages i.e. quoted amount is not less than the prepriced amount i.e. Rs 27,03,441.00. If quoted amount is less than the prepriced amount, same will be amended to pre-priced amount.Amount so adjusted will be deducted from quoted amount against Sch A Part-I i.e. Item No. 1.00 of BOQ. Quoted Amount of tender as a whole will remain unchanged due to this adjustment. 127 Comprehenisve maintenance of Solar Power Plant 0.8 MWpfor FIRST YEAR after expiry of DLP of Ph-I of the subject work with including periodical Check up andmaintenance as per OEM recommendation& connected accessories through Authorised Original Equipment Manufacturers Service Centre Engineersor through OEM Certified Agencies as approved by GE, complete all as specified and as directed. NOTE :-(a) Service engineer will carry scheduled preventative maintenance checks on SPV as per the standard check list of the OEM (b) Service engineer shall carry out checks on Solar Plant, as per the manufacturer’s check list and as directed by Engr-in Charge and would correct / recommend / suggest improvement in operation and performance. (c) Service Engineer during the visit will report on the performance or any other abnormality and inform parts requirement, shall also submit the report on work done and recommendations as well as spare parts offers to the concerned authority for arrangement.(d)Cost of equipment and spare parts which is not covered in warranty and DLP shall be measured in PC Sum andcost of item priced upto ₹500.00 shall be deemed to be included in the comprehenisve maintenance quoted cost. Repairs of minor components any other major components are also in the scope and cost of labour for minor / major components is deemed to be included in the quoted rate for this item.(e) Cost of gaskets, metal/rubber washer, CI washer special cement and small nuts/bolts and screws required for repair shall be deemed to be included in the unit rated quoted by the contractor. 128 Comprehenisve maintenance of Solar Power Plant 0.8 MWpfor SECOND YEAR after DLPof Ph-I of the subject work with including periodical Check up andmaintenance as per OEM recommendation& connected accessories through Authorised Original Equipment Manufacturers Service Centre Engineersor through OEM Certified Agencies as approved by GE, complete all as specified and as directed. NOTE :-(a) Service engineer will carry scheduled preventative maintenance checks on SPV as per the standard check list of the OEM (b) Service engineer shall carry out checks on Solar Plant, as per the manufacturer’s check list and as directed by Engr-in Charge and would correct / recommend / suggest improvement in operation and performance. (c) Service Engineer during the visit will report on the performance or any other abnormality and inform parts requirement, shall also submit the report on work done and recommendations as well as spare parts offers to the concerned authority for arrangement.(d)Cost of equipment and spare parts which is not covered in warranty and DLP shall be measured in PC Sum and cost up to Rs. 500.00 shall be deemed to be included in the comprehenisve maintenance quoted costrepairs of minor components any other major components are also in the scope of Annual Maintenance Contract.(e) Cost of gaskets, metal/rubber washer, CI washer special cement and small nuts/bolts and screws required for repair shall be deemed to be included in the unit rated quoted by the contractor. 129 Comprehenisve maintenance ofSolar Power Plant 0.8 MWpfor THIRD YEAR after DLPof Ph-I of the subject work with including periodical Check up andmaintenance as per OEM recommendation& connected accessories through Authorised Original Equipment Manufacturers Service Centre Engineersor through OEM Certified Agencies as approved by GE, complete all as specified and as directed. NOTE :-(a) Service engineer will carry scheduled preventative maintenance checks on SPV as per the standard check list of the OEM (b) Service engineer shall carry out checks on Solar Plant, as per the manufacturer’s check list and as directed by Engr-in Charge and would correct / recommend / suggest improvement in operation and performance. (c) Service Engineer during the visit will report on the performance or any other abnormality and inform parts requirement, shall also submit the report on work done and recommendations as well as spare parts offers to the concerned authority for arrangement.(d)Cost of equipment and spare parts which is not covered in warranty and DLP shall be measured in PC Sum and cost up to Rs. 500.00 shall be deemed to be included in the comprehenisve maintenance quoted cost repairs of minor components any other major components are also in the scope of Annual Maintenance Contract.(e) Cost of gaskets, metal/rubber washer, CI washer special cement and small nuts/bolts and screws required for repair shall be deemed to be included in the unit rated quoted by the contractor. 130 Comprehenisve maintenance ofSolar Power Plant 0.8 MWpfor FORTH YEAR after DLP of Ph-I of the subject work with including periodical Check up andmaintenance as per OEM recommendation& connected accessories through Authorised Original Equipment Manufacturers Service Centre Engineersor through OEM Certified Agencies as approved by GE, complete all as specified and as directed. NOTE :-(a) Service engineer will carry scheduled preventative maintenance checks on SPV as per the standard check list of the OEM (b) Service engineer shall carry out checks on Solar Plant, as per the manufacturer’s check list and as directed by Engr-in Charge and would correct / recommend / suggest improvement in operation and performance. (c) Service Engineer during the visit will report on the performance or any other abnormality and inform parts requirement, shall also submit the report on work done and recommendations as well as spare parts offers to the concerned authority for arrangement.(d)Cost of equipment and spare parts which is not covered in warranty and DLP shall be measured in PC Sum and cost up to Rs. 500.00 shall be deemed to be included in the comprehenisve maintenance quoted cost repairs of minor components any other major components are also in the scope of Annual Maintenance Contract.(e) Cost of gaskets, metal/rubber washer, CI washer special cement and small nuts/bolts and screws required for repair shall be deemed to be included in the unit rated quoted by the contractor. 131 Comprehenisve maintenance of Solar Power Plant 0.8 MWpfor FIFTH YEAR after DLPof Ph-I of the subject work with including periodical Check up andmaintenance as per OEM recommendation& connected accessories through Authorised Original Equipment Manufacturers Service Centre Engineersor through OEM Certified Agencies as approved by GE, complete all as specified and as directed. NOTE :-(a) Service engineer will carry scheduled preventative maintenance checks on SPV as per the standard check list of the OEM. (b) Service engineer shall carry out checks on Solar Plant, as per the manufacturer’s check list and as directed by Engr-in Charge and would correct / recommend / suggest improvement in operation and performance. (c) Service Engineer during the visit will report on the performance or any other abnormality and inform parts requirement, shall also submit the report on work done and recommendations as well as spare parts offers to the concerned authority for arrangement.(d) Cost of equipment and spare parts which is not covered in warranty and DLP shall be measured in PC Sum and cost up to Rs. 500.00 shall be deemed to be included in the comprehenisve maintenance quoted cost repairs of minor components any other major components are also in the scope of Annual Maintenance Contract.(e) Cost of gaskets, metal/rubber washer, CI washer special cement and small nuts/bolts and screws required for repair shall be deemed to be included in the unit rated quoted by the contractor. 132 Prime Cost Sum. The prime cost to be used as directed by the Accepting Officer vide Condition 1 (v) and 5 of IAFW-2249 (General Condition of Contracts) forming part of the tender documents.(a) Provide a prime cost of Rs.3,00,000.00 forsupply only of spare parts required for comprehensive maintenance after expiry of DLP of Phase-I, through a BOO convened by the CWE. The spares shall procured directly from the OEMs or their aurhorised distributor/dealer as approved by GE.(b) Bidders/Contractors quoted amount shall be inclusive of his overhead and profit and including all taxes and insert amount to cover all. The Bidders/Contractors is to quote lump sum amount under Column 6 covering all the aspects mentioned here in before, representing (%) percentage under Column 9, Above/Below (+ or - denomination) the Prime Cost Sum inserted by MES under Column 5. However, the quoted amount under Column 6 shall not exceed 15% (Fifteen Percentage) of Prime Cost Sum inserted by MES under Column 5. In case, the Bidders/Contractors quoted amount is in excess of 15% of the estimated amount, the same shall be restricted to 15% (Fifteen Percentage) and the amount quoted shall be corrected accordingly to work out the contract sum. Item Continued as 70.01 133 NOTE:-Prime Cost Sum shall be governed in terms of condition 1 (v) and 5 of IAFW-2249 (General Condition of Contract) and to be regularized through Deviation Order. The following procedure shall be adopted to execute the Prime Cost Sum :-(a) Step –I Service Engineer of OEM along with site executive shall visit every month for Preventive and corrective maintenance on all the Solar Power Plant as specified in BOQ herein before, and undertake routine comprehensive maintenance and identify the list of damage / defective spare parts in Solar Power Plant. Service Engineer have to submit report to concerned Engr-in Charge and BOO before undertaking replacement/ repairs, except in case of emergency.(b) Step –II Subsequently BOO will verify the same and submit the finding to the CWE after assembly of board in terms of CA Provision for concurrence.(c) Step –III After concurrence of BOO, the Engr-in-Charge will direct the contractor and the service provider to replace the unserviceable spare parts.(d) Step –IV Serviceability certificate of Solar Power Plant duly signed by the Service Engineer, BOO findings, GST enabled purchase voucher for the replaced spare parts alongwith draft DO details shall be submitted to the GE for placing of DO’s. The advance on account shall be accompanied alongwith the said DO’s for payment.

BRR : 7822844 REPAIR/ MAINT OF PUMP, MOTOR, STARTER, DOZING SYSTEM, SWIMMING POOL COMPRESSOR, RAISING MAIN, GATE VALVE, PERIODICAL CLEANING OF TANKS & OTHER MISC WORKS AT AFTC, 2 DC AREA & AFS JALAHALLI EAST WEST AREA; M&L for taking down defective centrifugal pump set 100 HP capacity by disconnecting the pump from motor after unscrewing nuts/ bolts of coupling, foundation, suction pipe delivery pipes and shifting of pump to workshop for repair/ servicing, comprising strip opening of pump, replacement of any defective parts, carrying out necessary lath work, re-assembling and shifting from workshop to site, re-installation at same location as directed by Engr-in-Charge, testing on full load capacity at least for 8 hrs, complete all as specified and as directed. Note :-(a)The spares shall be measured and paid seperately in the relevent items given below.(b) Cost of labour for replacement of spares and transportation are deemed to be included in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty @ Rs 1000 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other than the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 2 Supply only Ball bearing suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed.Make : Tata/SKF/NBC 3 Supply only coupling Rubber Bush suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 4 Supply only split casing gaskets suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 5 Supply only shaft sleeves suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 6 Supply only coupling bolt with nuts suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 7 Supply only water seal suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 8 Supply only Air cock grease nipple suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 9 Remetaling of shaft, turning, grinding as per the required size and polishing including provision of neck rings of impellers suitable for 100 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 10 Supply only bronze impeller suitable for 100 HPcapacity motor pump as per manufacturers design complete all as specified and as directed. 11 M&Lfor suitable size of gland packing for 100 HP pump set as per manufacturers design complete all as specified and as directed. 12 Supply & fix in replacement of 3 Pole power contactor AC 415 V 160 Amps ,AC3 ( inductive load ) type with Aux contact 2 NO + 2 NC50 Hz Model No. as per existing framesuitable for 100 HP Pump sets complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 13 M & L for servicing of starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedfor the100 HP capacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be include in quoted rate. 14 Supply & fix in replacement adjustable CT/Direct operated thermal over load relay 105 to 156 A for 100 HP motor 3 phase 415v , 3 pole , with single phase protection including CTs complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 15 M&L for rewinding ofsquirrel cage induction electrical motor , 3 phase, 415 volts with suitable size of copper enameled winding wire and insulating materials incl disconnecting all electrical connections ,decoupling from pump,taking down the motor from foundation , cleaning and varnishing the stator & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation by using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections,checking the vibrations, RPM and testing on full load complete all as specified and directed for 100HPmotor capacity. 16 M&L for taking down defective centrifugal pump set 60 HP capacity by disconnecting the pump from motor after unscrewing nuts/ bolts of coupling, foundation, suction pipe delivery pipes and shifting of pump to workshop for repair/ servicing, comprising strip opening of pump, replacement of any defective parts, carrying out necessary lath work, re-assembling and shifting from workshop to site, re-installation at same location as directed by Engr-in-Charge, testing on full load capacity at least for 8 hrs, complete all as specified and as directed. Note :-(a)The spares shall be measured and paid seperately in the relevent items given below.(b) Cost of labour for replacement of spares and transportation are deemed to be included in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty @ Rs 1000 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other than the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 17 Supply only Ball bearing suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed.Make : Tata/SKF/NBC 18 Supply only coupling Rubber Bush suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 19 Supply only coupling bolt with nuts suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 20 Supply only shaft sleeves suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 21 Supply only split casing gaskets suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 22 Supply only water seal suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 23 Supply only Air cock grease nipple suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 24 Remetaling of shaft, turning, grinding as per the required size and polishing including provision of neck rings of impellers suitable for 60 HP capacity motor pump as per manufacturers design complete all as specified and as directed. 25 Supply only bronze impeller suitable for 60 HPcapacity motor pump as per manufacturers design complete all as specified and as directed. 26 Supply and fix in replacement of mechanical flexible UT tyre rubber coupling suitable for 60 HP centrifugal pump set with cast iron flange, natural rubber coupler, mild steel clamping ring, high tensile strength Grade suitable size of Hex bolts, including aligning motor - centrifugal pump with a tolerance of +- 4mm, testing complete all as specified and directed. 27 M&Lfor suitable size of gland packing for 60 HP pump set as per manufacturers design complete all as specified and as directed. 28 M & L for servicing of starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedfor the60 HP capacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be included in quoted rate. 29 Supply & fix in replacement of 3 Pole power contactor AC 415 V AC3 ( inductive load ) type 100 Amps, AC3 type 2 NO + 2 NC50 Hz Model No. as per existing frame suitable for 60 HP Pump sets complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 30 Supply & fix in replacement adjustable CT/Direct operated thermal over load relay75 to 110 A for 60 HP motor 3 phase 415v , 3 pole , with single phase protection including CTs complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 31 Supply & fix in replacementSingle phase preventer for motor in the existing panel board with new one at water supply installations complete all as specified and as directed. 32 Supply & fix in replacement Star Delta timer 0-30/60 sec complete all as specified and as directed. 33 M&L for rewinding ofsquirrel cage induction electrical motor , 3 phase, 415 volts with suitable size of copper enameled winding wire and insulating materials incl disconnecting all electrical connections ,decoupling from pump,taking down the motor from foundation , cleaning and varnishing the stator & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation by using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections,checking the vibrations, RPM and testing on full load complete all as specified and directed for 60 HPmotor capacity. 34 Taking down defective centrifugal pump set 25 HP by disconnecting the pump from motor after unscrewing nuts/ bolts of coupling, foundation, suction pipe delivery pipes and shifting of pump to workshop for repair/ servicing, comprising strip opening of pump, replacement of any defective parts, carrying out necessary lathe work, re-assembling and shifting from workshop to site, re-installation at location as directed by Engr-in-Charge, testing on full load capacity at least for 8 hrs, complete all as specified and as directed. Note :- (a)The spares shall be measured and paid seperately in the relevent items given below.(b) Cost of labour for replacement of spares and transportation are deemed to be incl in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty @ Rs 500 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other then the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 35 Supply only Ball bearing suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed.Make : Tata/SKF/NBC 36 Supply only split casing gaskets suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 37 Supply only Air cock grease nipple suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 38 Supply only water seal suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 39 Supply only coupling bolt with nuts suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 40 Supply only coupling Rubber Bush suitable for 25HP motor pump as per manufacturers design complete all as specified and as directed. 41 Supply only shaft sleeves suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 42 Supply only bronze impeller suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 43 Remetaling of shaft, turning, grinding as per the required size and polishing including provision of neck rings of impellers suitable for 25 HP motor pump as per manufacturers design complete all as specified and as directed. 44 M&Lfor suitable size of gland packing for 25 HP pump set as per manufacturers design complete all as specified and as directed. 45 Supply & fix in replacement adjustable CT/Direct operated thermal over load relay30 to 43 A for 25 HP motor 3 phase 415v , 3 pole , with single phase protection including CTs complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 46 Supply & fix in replacement of3 Pole power contactor AC 415 V AC3 ( inductive load ) type 40 Amps with add on aux contact 2 NO + 2 NC50 Hz Model No. as per existing framesuitable for 25 HP Pump set complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 47 M & L for servicing of starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedthe25 HP capacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be included in quoted rate. 48 M&L for rewinding ofsquirrel cage induction electrical motor , 3 phase, 415 volts with suitable size of copper enameled winding wire and insulating materials incl disconnecting all electrical connections ,decoupling from pump,taking down the motor from foundation , cleaning and varnishing the stator & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation by using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections,checking the vibrations, RPM and testing on full load complete all as specified and directed for 25 HPmotor capacity. 49 Supply and fixing in repair of3 phase star delta pump starter suitable for 25 HP centrifugal pump with over load relay of suitable current rating,timer relay ,single phase preventor fixing in existing enclosure including all connected accessories complete all as specified and directed Make : L&T/Indoasian/Schenider/Havells 50 Supply and fix as in repair 4 Pole MCCB ,415 volts,fixed type ,160 Amp, 50 Hz, with rupturing capacity 25 KA in theexisting pump starter panel including connecting up incoming/out going cables with suitable lugs and testing complete all as specified and as directed. Make: Indoasian/L&T/ Legrand 51 Taking down and relaying of existingDI water pipe lines of size 300 mm bore but of any type including all fittings after removal of scaling, cleaning and flushing etc complete all as specified and directed.Note:Excavation & earthwork shall be measured & paid seperately 52 Taking down and relaying of existingDI water pipe lines of size 200 mm bore but of any type includings all fittings after removal of scaling, cleaning and flushing etc complete all as specified and directed.Note:Excavation & earthwork shall be measured & paid seperately 53 M&L as in replacement for Ductile Iron Pipe (DI Pipes), ISI marked, Class K-7, 300 mm dia laid in trenches including jointing material such as EPDM Rubber Gasket and suitable type of grease etc complete all as specified and directed.Note :- DI fitting/special shall be measured and paid separately.Note:Excavation & earthwork shall be measured & paid seperately 54 Supply and fixing in replacement Sluice valve of size 300 mm dia Cl body, both ends flanged duly drilled, ISI marked with IS-14846-2000, PN-1.6 having Stainless Steel spindle and check nut including operating wheel, fixing with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed 55 Material and Labour for dismantling the brassspindle from 300 mm dia bore sluice valves in various locations and reconditioning the sluice valve by replacing SS/bronze spindle, spindle nuts with brass ring, gland nuts complete all as specified and as directed. 56 Material and Labour for gland packing in leaking Sluice Valves of 300 mm dia size Complete including replacing/tightening the existing bolts and nuts etc. complete all as directed . 57 Cutting the existing broken / cracked CI/DI/GI/Asbestos Cement Pipe line of size upto 300mm dia, by dewatering the leakage water from site and removing the old pipe line and addition / alteration to pipe by providing new pipe,welding,bending,grinding,including all accessories such as tee,elbow,collar etc , and ensure no leakage with pressure test complete all as specified and directed , Note : Pipes and mechanical collar shall be measured and paid seperately 58 M&L for specials fittings suitable for Cast iron / ductile iron /Asbestos cement pipe made out of MS Plate of 12 mm thick complete with mechanical/detachable type arrangement as per site requirementwith MS bolts and nuts of suitable size and MS sheet fabricated to required dia of pipe for prepration of collar/flange, on any pipe leak or cracks of pipe for arresting the leakage complete including rubber ring, packing rubber sheet,set of two collar rings of size 300 mm borecomplete all as specified and as directed. 59 M&L as in replacement for Ductile Iron Pipe (DI Pipes), ISI marked, Class K-7, 200 mm dia laid in trenches including jointing material such as EPDM Rubber Gasket and suitable type of grease etc complete all as specified and directed.Note :- (i)DI fitting/special shall be measured and paid separately. (ii)Excavation & earthwork shall be measured & paid seperately 60 S&F in replacementfoot valve (confirming to IS-4038) cast iron of size 200 mm bore including rubber insertion, packing material, nuts, bolts, and washer with suitable new one all as specified and directed. 61 Supply and fixing in replacement Non return valve (confirming to IS-5312) (NRV) of size 200 mm ISI marked, CIbody suitable for 200 mm dia pipe line complete all specified and directed 62 Supply and fix replacement of U/S leather packing suitable for foot valve 150 to 200 mm dia, suction pipe flanged connected to pumpsets including replacement ofnuts and bolts etc all as specified and directed 63 Supply and fixing in replacement Sluice valve of size 200 mm dia Cl body, both ends flanged duly drilled, ISI marked with IS-14846-2000, PN-1.6 having Stainless Steel spindle and check nut including operating wheel, fixing with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed 64 Material and Labour for dismantling the brassspindle from 200 mm dia bore sluice valves in various locations and reconditioning the sluice valve by replacing SS/bronze spindle, spindle nuts with brass ring, gland nuts complete all as specified and as directed. 65 Material and Labour for gland packing in leaking Sluice Valves of 200 mm dia size Complete including replacing/tightening the existing bolts and nuts etc. complete all as directed . 66 Material & Labour as in repair for Construction ofValve pit having inner dimensions 1200 mm x 1200 mm x 1200 mm with foundation PCC 1:4:8 type D2 using 40mm grade stone aggregate, brick work with sub class B old size bricks built in Cement mortar 1:6, PCC 1:2:4 type B1 using 20mm stone aggregate for Coping, 15 mm thick rendering plaster in CM 1:4 inluding MS cover with locking arrangement all as specified and as directed.Note :- MS work as in chamber cover shall be measured and paid separately under relevant item of this schedule. 67 Cutting the existing broken / cracked CI/DI/GI/Asbestos Cement Pipe line of size upto 200mm dia, by dewatering the lekage water from site and removing the old pipe line and addition / alteration to pipe by providing new pipe,welding,bending,grinding,including all accessories such as tee,elbow,collar etc , and ensure no leakage with pressure test complete all as specified and as directed. Note : Pipes and mechanical collar shall be measured and paid seperately 68 M&L for specials fittings suitable for Cast iron / ductile iron /Asbestos cement pipe made out of MS Plate of 12 mm thick complete with mechanical/detachable type arrangement as per site requirementwith MS bolts and nuts of suitable size and MS sheet fabricated to required dia of pipe for prepration of collar/flange, on any pipe leak or cracks of pipe for arresting the leakage complete including rubber ring, packing rubber sheet,set of two collar rings of size 200 mm borecomplete all as specified and as directed. 69 Clearing the bushes trunk girth not exceeding 10 .00 cm and area around valve chambers upto 1.0 mtrs and depositing at a distance not exceeding 50 mtrs from starting point complete all as specified and directed 70 Demolition of Brickwork or precast concrete block walling including wall quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone work and concrete articles built in cement mortar complete all as specified or directed. 71 M&L for Pre-cast cement concrete block masonry in PCC (1:3:6) type C-1 using 20mm grade stone aggregate with solid blocks, exc.10 cm in width and setting in cement mortor 1 : 4, complete, in walls all as specified and directed. 72 Over hauling and repair to Chemical Dosing Pump Granual based chloronome plants at Range pump houseby cleaning the FRP 150 Ltrs Tank, and cleaning of filters and NRV , checking and cleaning the delivery pipe line for chocking , cleaning of chlorination plant and maintainig properly including checking the level of oil in the gauge and topping up as and when required, checking the glands and maintain the plant in all respect and replacement of minor spare for smooth functioning of Chlorination Plant all as directed by Engineer in charge. Note:- The unit rate quoted shall be deemed to include for the cost of replacement of minor spares such as O rings , nut/screws,washers,bolt, cleaning waste , toolsfor routine day to day maintenance and necessary servicing to keep the plants in running condition on all days includingSunday and holidays, Replacement of other major spares shall be measured and paid for separately under respective item of BOQ 73 All as per item No 72 but at E & ITI OH Tank complete all as specified and directed. 74 All as per item No 72 but at Double Tank complete all as specified and directed. 75 All as per item No 72 but at ETI OH Tank complete all as specified and directed. 76 Supply onlyO-tolodine chlorine solution in packing of 200ml bottle for testing of chlorine content in water 77 Supply onlyChlorine dosing pistonpump unit complete 78 Supply only Rubber ring for mixing chamber 79 Supply onlyPVC NRV set with glass ball for suction and delivery adopter 20 mm dia 80 Supply onlyTeflon gland square type 3 mm for smooth functioning of Chlorination plant 81 Supply only PVCdiaphram valve 25 mm dia heavy duty 82 Supply only Agitator mixing assembly with motor 83 Supply only Chlorine test kit with coloured sample Complete with all testing fitments and OT - solution in Rexene finished box Complete all as specified and as directed 84 Supply of calcium based high strength chlorination chemical for water in granular form chlorine concentration level having 65%-70% chlorine content packed in 45 Kg capacity in factory sealed HDPE Container superior quality suitable for treatment of drinking water complete all as specified and directed.Note:The material shall be delivered at watersupply installation as per direction of AGE E/M as & when required during the contract period. 85 Material and labourfor Attending day to day water supply service related complaintslike choking of rising main pipes of buildings, blockage in control valves/ float valves/ pipe fittings, etc, applying necessaryengineering efforts like dismantle of pipes and fittings to clean and remove blocking objects, descaling of pipes, re-fixing of pipes on wall, etc to restore the proper flow of water to service tanks all as specified and directed. 86 Note :- (a) The contractor has to attend above mentioned job in any location of AFTC, 2 DC and entire AFS jalahalli East and West area 87 (b)The service tanks are positioned on roof top of multi storied buildings upto three storey. Contractor is responsible to ensure that the labour employed should be equipped with safety items like industrial helmet, safety belt, extensible ladder of 40 feet length, plumbing and cuttings tools, etc. 88 (c) The cost of rethreading of GI pipes of 25mm dia and adding of new GI nipple of suitable length after rethreading is deemed to be included in the quoted rate. 89 (d) Due to shortage of water in the station, the repair work and testing required under this item need to be carried out during water supply distribution hours i.e. 5:30 AM to 7:30 AM. Nothing extra shall be permitted in this regard. 90 (e) The cost of repair to the damages of cemented surfaces/ external finishes/ metal clamps of rising pipes are also deemed to be included in the quoted rate. 91 (f)In case of any delay in attending the complaint more than 6 hrs after handing over routine/urgent complaints, the contractor shall be liable to pay the penalty as described in penalty clause given here as under. 92 (g)If the delay is more then 06 hrs period and the GE is not satisfied with the reason for delay then penalty at the rate of Rs 100/- per job shall be deducted from the dues of the contractor. Please note that this penalty is exclusively other then the condition 67 of IAFW - 2249 and shall be treated as interim condition of the contract and shall be enforce above as and when delay in individual job is noticed and no claim whatsoever on this account shall be entertained by the Deptt. 93 (h) The decision of the Accepting Officer in this regard shall be final and binding. 94 Supply and fix Nipple suitable for HDPE water tankof size 20 mm complete all as specified and as directed. 95 Supply and fix Nipple suitable for HDPE water tankof size 25 mm complete all as specified and as directed. 96 Supply and fix in repairs lids for polyethylene water storage tanks, threaded or hinged type as per existing incl PTMT nuts/binding wire suitable up to 1000Ltrs cap of tanks complete all as specified and directed by Engineer-in Charge 97 Supply and fix in replacement PVC Ball valve ISI marked high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of size 20 mm complete all as specified and directed 98 Supply and fix of PVC water tank 500 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I ,complete all as directed incl disconnecting existing tank of any description and any capacity complete. 99 Supply and fixingin repair 25 mm dia Unplasticiced PVC Pipes of pressure rating 10kgf/cm2including fittings like socket / union / Tee / Reducer / Nipple etc complete fixed to wall/ceilings/ in floors etc, complete all as specified and directed. 100 Supply and fixing in repair20 mm dia Unplasticiced PVC Pipes of pressure rating 10kgf/cm2including fittings like socket / union / Tee / Reducer / Nipple etc complete fixed to wall/ceilings/ in floors etc, complete all as specified and directed. 101 Supply and fixingin repair UPVC Gate Valve of size 25 mm dia , ISI marked complete all as specified and as directed. 102 Supply and fixingin repair UPVC Gate Valve of size 20 mm dia, ISI marked complete all as specified and as directed. 103 Supply and fixingin repair 20 mm dia Chlorinated PVC (CPVC) Pipes of pressure rating 10kgf/cm2including fittings like socket / union / Tee / Reducer / Nipple etc complete fixed to wall/ceilings/ in floors etc, complete all as specified and directed. 104 Supply and fixingin repair 25 mm dia Chlorinated PVC (CPVC) Pipes of pressure rating 10kgf/cm2including fittings like socket / union / Tee / Reducer / Nipple etc complete fixed to wall/ceilings/ in floors etc, complete all as specified and directed. 105 Supply and fixingin repair Chlorinated PVC Gate Valve of size 20 mm dia, ISI marked complete all as specified and as directed. 106 Supply and fixingin repair Chlorinated PVC Gate Valve of size 25 mm dia, ISI marked complete all as specified and as directed. 107 Supply and fix in repairs lids for polyethylene water storage tanks, threaded or hinged type as per existing incl PTMT nuts/binding wire suitable for1001 to 5000 Ltrs cap of tanks complete all as specified and directed by Engineer-in Charge 108 Supply and fix in replacement PVC Ball valve ISI marked high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of size 25 mm complete all as specified and directed 109 Supply and fix of PVC water tank 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I ,complete all as directed incl disconnecting existing tank of any description and any capacity complete. 110 Taking down and relaying of existingserviceable GI tubing / connection in new or old positions including cleaning, cutting, threding all as directed, along with new GI fittings where ever replaced and required at site of size 40 to 50 mm bore complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 111 Taking down and relaying of existing serviceable GI tubing / connection in new or old positions including cleaning, cutting, threding all as directed, along with new GI fittings where ever replaced and required at site of size 25 mm bore complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 112 Taking down and relaying of existingserviceable GI tubing / connection in new or old positions including cleaning, cutting, threding all as directed, along with new GI fittings where ever replaced and required at site of size 20 mm bore complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 113 Taking down and relaying of existingserviceable GI tubing / connection in new or old positions including cleaning, cutting, threading all as directed, along with new GI fittings where ever replaced and required at site of site of size 15 mm borecomplete all as specified directed. 114 Supply & Fix as in replacement of GI tubing medium grade of size 50 mm bore with all fittings on wall/ trenches complete including cutting and thereading all as required at site complete all as specified directed.Note:Excavation & earthwork shall be measured & paid seperately 115 S&F in replacement Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 50mm complete all as specified and directed. 116 Supply & Fix as in replacement of GI tubing medium grade of size 40 mm bore with all fittings on wall/ trenches complete including cutting and thereading all as required at site complete all as specified directed.Note:Excavation & earthwork shall be measured & paid seperately 117 S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 40 mm complete all as specified and directed. 118 Supply & Fix as in replacement of GI tubing medium grade of size 25 mm bore with all fittings on wall/ trenches complete including cutting and thereading all as required at site complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 119 S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 25 mm complete all as specified and directed. 120 Supply & Fix as in replacement of GI tubing medium grade of size 20 mm bore with all fittings on wall/ trenches complete including cutting and thereading all as required at site complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 121 S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20 mm complete all as specified and directed. 122 Supply & Fix as in replacement of GI tubing medium grade of size 15 mm bore with all fittings on wall/ trenches complete including cutting and thereading all as required at site complete all as specified directed. Note:Excavation & earthwork shall be measured & paid seperately 123 S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 15 mm complete all as specified and directed. 124 S & F in replacement Bib taps, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe fixed of size 15 mmfor brass ferrule fancy type and fixed complete all as specified and directed. 125 Supply and fix Nipple suitable for HDPE water tankof size 40 mm complete all as specified and as directed. 126 Supply and fix in replacement PVC Ball valve ISI marked high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of size 40mm complete all as specified and directed 127 Supply and fix PVC water tank 2000 Ltrs Capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, complete all as directed incl disconnecting existing tank of any description and capacity complete. 128 Supply and fixingFramed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, hinges and handles etc. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 for valve pit chamber, raising main support and motor foundation supports etc.complete all specified and directed. 129 M & L for Over hauling and repair/replacement of unserviceable items ofPortable RO unit of capacity 80 LPD by disconnecting all pipe lines, filters catridges, RO Membrane , motor, float valveand water storage tank,all filter catridges(Pre Activated carbon ,Post Activated carbon, inline sedimant , pre particle filter), motor carbon brushes, pressure pump diaphram, float valve,solenoid valve,12/24v SMPS power supply unit , damaged piles lines , bends ,tee , elbow, water flow restrictor including cleaning of water storage tanks and testing (TDS ), fixing of pre filtersall respect and replacement of minor spare such as carbon brush ,tee ,elbow,pipe line,teflon tape,screws,nuts etc include in this quoted rate for smooth functioning of RO Plant complete all as specified and as directed.Note : Major spare parts shall be measured and paid seperately as supply only under relevant items of BOQ. 130 Supply only Reverse Osmosis membrane with clamps suitable for RO unit all as specified 131 Supply only Inline sediment filter with clamps suitable for RO unit all as specified 132 Supply only pre particle filter with food grade housing arrangement and with clamps suitable for RO unit all as specified 133 Supply only pre-activated carbon filter with clamps suitable for RO unit all as specified 134 Supply only Pressure pump 12/24vsuitable for RO unit all as specified 135 Supply only float switch suitable for RO unit all as specified 136 Supply only Post-activated carbon filter with clamps suitable for RO unit all as specified 137 Supply only RO pressure Pump Diaphram Head unitsuitable for RO unit all as specified 138 Supply only TDS,PH,Chlorine mesauring digital device all as specified 139 Supply only solenoid 12/24vsuitable for RO unit all as specified 140 Supply only 12/24v SMPS suitable for RO unit all as specified 141 Supply and fixing as in repair pre filter housingelementwithsuitable size of filter to protect RO includingPVC pipe of required length and all connected items complete all as specified and directed. 142 Supply, install, testing and commissioning ofChemical Dosing system havingtop dia 540mm x bottom dia 480mm x height 575 mm, net capacity 95 - 100 Ltr consisting of (i) water inlet line (ii) Dosing pump inlet arrangement (iii) Drain (iv) Overflow (v) Level Gauge (vi) inspection port (vii) Agitator 120 watt 800 - 900 RPM Single Phase flange mounted motor with plastic shaft and impeller (ix) provision of mounting Pump on Lid/wall along with dosing Injector of the following specification. Adjustble dosing pump max pressure 5kg/cm square& max flow rate 0 - 50 ltr / hr including all accessories such asLead tubing, Connecting Ferrules, check valves, non return valve all as directed. Power input 230V, 50 Hz, 40 SPM 1/30 fractional Horsepower, etc complete all as specified and directed. Make: - Model No. VST 1011 of Ravi Enterprise or equivalent as per E-in-Cs approved make.Note: Unit quoted rate shall be inclusive of taking down of old unserviceableplant and depositing same to MES store yard . 143 M&L for dewateringof Swimming Pool of size 50m x 25m (Olympic size pool ),Cleaning of Swimming pool bed,vertical walls complete with high pressure water jet to remove all masses, algae and dirt and removal of dirty waterwith sludge using non clog sludge machine and disposal of the same to a safe distance & applying of anti bacterial sterlization spray to walls, floors and applying muriatic acid, caustic soda or any other cleaning agent without damaging the existing tiles. Finally washing total surfaces with fresh water and make ready for fill up and ceilings all as directed.Note: (a) The Rate quoted by the contactor is deemed to include labours,tools and acessories andprovision of stickering of date of cleaning on the existing boardletter / figures White or Black colour and size as per existing font. (Date of Cleaned in format of (DD/MM/YY) Note : chemicals used for cleaning/PH level stablizer/anti Baterial/anti algae controller shall be supplied under relevant items 144 All as per Sl Item No. 143 here-in-before but Diving Pool of size 20 x 20 Meter complete all as specified and as directed. 145 All as per Sl Item No. 143 here-in-before but Balancing Tank of capacity 1,00,000 Gallon complete all as specified and as directed. 146 Supply only swimming pool grade Copper Sulphate crystal of superior qualityincluding stocking/ Handling and shifting complete all as specified and directed. 147 Supply only Swimming pool grade Hydro Chloric Acid (HCL) for regulating PH value of the pool complete all as specified and as directed. 148 Supplyonly swimming pool grade calcium based(Sodium Hypochloride) for water disinfectant as liquid form insealedcontainerhaving, chlorine concentration level not less than 12% and adding/mixing complete all as specified and as directed. 149 Supply only non ferrous Alum powder/crystal free from impurityclass Isuitable for swimming pools and adding/mixing as per direction of Engr-in-Charge to maintain water qualityincluding stocking/ Handling and shifting complete all as specified and directed. 150 Supply only Soda ash free from impurityclass Isuitable for swimming pools and adding/mixing as per direction of Engr-in-Charge to maintain water qualityincluding stocking/ Handling and shifting complete all as specified and directed. 151 Supply only Algae control gel/liquidfree from impurityclass Isuitable for swimming pools and adding/mixing as per direction of Engr-in-Charge to maintain water qualityincluding stocking/ Handling and shifting complete all as specified and directed. 152 Supply only chemically non reactive/lab quality Plastic mug 1 ltrs capacity complete all as specified and as directed. 153 Supply and fix in replacement ofchemically non reactive/Lab qualityPlastic bucket 35 ltrs capacity complete all as specified and as directed. 154 Supply and fix in replacement of nylon brush (soft quality) with wooden/HDPEbase of size 3 feet long, 2.5 (Inch) wide localy available best quality, suitable for fix with suction sweeper.complete all as specified and as directed. 155 Supply and fix in replacement ofnylon brushwithHDPEbase of size >18 Inch wide and handle > 20 feet long wide localy available best quality for cleaning walls of swimming pool complete all as specified and as directed. 156 Supply and fix in replacement offlexible pipe from suction sweeper pumps and Supply & fix PVC flexble hose pipe50mm OD including necessary jubilee clamps complete all as specified and as directed. 157 Supply and fix in replacement of nylon rope 25mm dia for suctionsweeper ( as per sample) complete all as specified and as directed. 158 Material and labour for opening the pressure filter vessel located in swimming pool of dia 2.8 Meter and height 2.6 meter for the following works:-(a)Opening the man hole cover and taking out entire filter media ie, existing stone aggregate , sand, quartz , slugde, algae etc(b)Cleaning of entire surfaces of sides , top and bottom of vessel by applying hydrochloric acidand thorough rinsing and make the vessel fit for re-filling the filter media.(c)Applying one coat of approved anti corrosive paint to entire internal surfaces of pressure filter including preparation of surfaces.(d) Re-fill the filter media with approved material of stone aggregate, river sand and white quartz in layers and properly packed upto existing level.All the material shall be rinsed thoroughly by using hydochloric solution and maintain the PH value at the range of 3 to 5.(e)Applying two coat of synthetic enamel paint to external surface of pressure filter vessel including preparation of surface etc and all as directed. 159 M&L for carrying out repair to trolley of suction sweeper pump set, including removing the pump and motor assembly carefully, dismantling rusted, bent or damaged MS frame members, cleaning entire surface, cutting and replacing corroded angle/channel sections with new mild steel of suitable size, welding, grinding and aligning to restore structural integrity. Work includes replacement of defective or jammed trolley wheels with new heavy-duty rubber/PU wheels of suitable load capacity, including fabrication of axle if required, welding, fitting and alignment. Entire metal frame surface shall be cleaned of rust and old paint using wire brush/scraper, then applied with one coat of red oxide primer and two coats of synthetic enamel paint of approved shade. Pump and motor set shall be re-mounted securely on trolley after repairs, reconnecting all mounting hardware as directed by Engineer-in-Charge, complete all as specified and directed. 160 M&L for carrying out repairs to 900mm wide suction sweeper head including dismantling the existing head assembly, cleaning and removing rust, replacing damaged or worn-out wheels with new nylon/plastic rollers of suitable size, fabricating and welding broken or bent brackets, repairing or replacing the metal body plate with mild steel sheet of suitable gauge, grinding sharp edges, tightening or replacing fasteners, restoring proper alignment of brush head and roller arms. Work includes thoroughly cleaning the base frame and applying one coat of red oxide primer and two coats of synthetic enamel paint for corrosion protection. The nylon bristle brush shall be checked for wear and refixed/replaced if found loose or damaged, ensuring smooth and uniform contact during sweeping operation. Complete all as specified and as directed by the Engineer-in-Charge 161 M&L for rewinding of 3-phase squirrel cage induction motor of capacity up to 3 HP, including removing the motor from its base, opening the end covers, dismantling the rotor, cleaning the stator core, removing burnt winding, preparing slots, rewinding the stator coils with super enamelled copper wire of same gauge and turns as per manufacturers specification, insulating with Class F insulation material, inserting wedges, varnishing with high-grade insulating varnish, oven drying, reassembling all components, aligning bearings, replacing terminal leads, testing for insulation resistance and load performance. Work includes cost of copper wire, insulating materials, varnish, labour, and testing equipment. Motor shall be tested under full load conditions for a minimum of 2 hours to ensure proper functioning. Complete all as specified and directed by the Engineer-in-Charge 162 M&L for carrying out repair to 3-phase DOL (Direct-On-Line) starter up to 5 HP capacity, including opening of enclosure, cleaning of all internal components, checking and tightening of loose terminals, replacing defective parts such as contactor coil, contacts, NO/NC auxiliary blocks, push buttons, overload relay, or indicator lamps with suitable rated spares as per original design, servicing of moving parts, reassembly, insulation testing, and functional testing under load conditions. The job includes cost of consumables like contact cleaner, terminal tags, and minor hardware. All replaced parts shall be measured and paid separately under relevant items. Complete all as specified and as directed by the Engineer-in-Charge 163 Taking down defective centrifugal/Monoblock pump set 10 HP to 15 HPby disconnecting the pump from motor after unscrewing nuts/ bolts of coupling, foundation, suction pipe delivery pipes and shifting of pump to workshop for repair/ servicing, comprising strip opening of pump, replacement of any defective parts, carrying out necessary lathe work, re-assembling and shifting from workshop to site, re-installation at location as directed by Engr-in-Charge, testing on full load capacity at least for 8 hrs, complete all as specified and as directed. Note :- (a)The spares shall be measured and paid seperately in the relevent items given below.(b) Cost of labour for replacement of spares and transportation are deemed to be incl in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty of Rs 500 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other then the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 164 Supply only Ball bearing suitable for 10 HP to 15 HPmotor pump as per manufacturers design complete all as specified and as directed.Make : Tata/SKF/NBC 165 Supply only coupling bolt with nuts suitable for 10 HP to 15 HPmotor pump as per manufacturers design complete all as specified and as directed. 166 Supply only coupling Rubber Bush suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 167 Supply only split casing gaskets suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 168 Supply only Air cock grease nipple suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 169 Supply only shaft sleeves suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 170 Supply only water seal suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 171 Remetaling of shaft, turning, grinding as per the required size and polishing including provision of neck rings of impellers suitable for 10 HP to15 HP motor pump as per manufacturers design complete all as specified and as directed. 172 Supply only bronze impeller suitable for 10 HP to 15 HP motor pump as per manufacturers design complete all as specified and as directed. 173 M&Lfor suitable size of gland packing for 10 HPto 15 HP pump set as per manufacturers design complete all as specified and as directed. 174 Supply & fix in replacement adjustable CT/Direct operated thermal over load relay15 to 21 A for 10 HP to 15 HP motor3 phase 415v , 3 pole , with single phase protection including CTs complete all as specified and as directed. Make : L & T / Indo Asian /Schneider 175 M & L for servicing of starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedfor the10 HP to 15 HP capacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be included in quoted rate. 176 Supply & fix in replacement of3 Pole power contactor AC 415 V AC3 ( inductive load ) type 25 Amps with add on aux contact 2 NO + 2 NC50 Hz Model No. as per existing framesuitable for 10 HP to 15 HP Pump sets complete all as specified and as directed.Make : L & T / Indo Asian /Schneider 177 M&L for rewinding ofinduction electrical motor , 3 phase, 415 volts with suitable size of copper enameled winding wire and insulating materials incl disconnecting all electrical connections ,decoupling from pump,taking down the motor from foundation , cleaning and varnishing the stator & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation by using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections,checking the vibrations, RPM and testing on full load complete all as specified and directed for 10 HP to 15 HPmotor capacity. 178 Taking down defective centrifugal /Monoblock pump set upto 5 HP by disconnecting the pump from motor after unscrewing nuts/ bolts of coupling, foundation, suction pipe delivery pipes and shifting of pump to workshop for repair/ servicing, comprising strip opening of pump, replacement of any defective parts, carrying out necessary lathe work, re-assembling and shifting from workshop to site, re-installation at location as directed by Engr-in-Charge, testing on full load capacity at least for 8 hrs, complete all as specified and as directed. Note :- (a)The spares shall be measured and paid seperately in the relevent items given below.(b) Cost of labour for replacement of spares and transportation are deemed to be incl in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty of Rs 500 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other then the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 179 Supply only coupling bolt with nuts suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 180 Supply only Ball bearing suitable for upto 5 HP motor pump as per manufacturers design complete all as specified and as directed.Make : Tata/SKF/NBC 181 Supply only split casing gaskets suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 182 Supply only coupling Rubber Bush suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 183 Supply only Air cock grease nipple suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 184 Supply only shaft sleeves suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 185 Supply only water seal suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 186 Remetaling of shaft, turning, grinding as per the required size and polishing including provision of neck rings of impellers suitable for upto 5 HP motor pump as per manufacturers design complete all as specified and as directed. 187 Supply only bronze impeller suitable for upto 5 HPmotor pump as per manufacturers design complete all as specified and as directed. 188 Supply and fix as in repair 4 Pole MCCB ,415 volts,fixed type ,125 Amp, 50 Hz, with rupturing capacity 25 KA in theexisting pump starter panel including connecting up incoming/out going cables with suitable lugs and testing complete all as specified and as directed. Make: Indoasian/L&T/ Legrand 189 M&L for rewinding ofelectrical motor , 3 phase, 415 volts with suitable size of copper enameled winding wire and insulating materials incl disconnecting all electrical connections ,decoupling from pump,taking down the motor from foundation /base, cleaning and varnishing the stator & rotor winding, heating and drying, replacement of burnt terminals, greasing to bearings, re-assembling the motor and refixing of motor on the foundation/ base of sunction sweeperby using new nut, bolts and washers, coupling with pump,checking alignment connecting all electrical connections,checking the vibrations, RPM and testing on full load complete all as specified and directed upto 5 HPmotor capacity. 190 M & L for servicing of starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedfor theupto 5 HPcapacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be included in quoted rate. 191 Supply and fix in replacement single phase 240V50HzDOL starter with OLR relay suitable for upto 4 HP monoblock pump sets inculding proper termination,testing and all connected acessories all as are specified and directed. 192 Cleaning of service tanks of the capacity as mentioned below on roof top of bldgs upto three storey after disconnection from inlet and outlet pipe, removing of float valve of service tank and keep aside safely for reuse drain out water through drain plug, cleaning thoroughly to remove all scales and dirt by brushing internal surface, cleaning properlyinside with soda wash, flushing out with fresh water, re-positioning of tank at same place, re-connecting inlet and outlet pipes, closing of drain plug, re-installation of float valve duly cleaned, writing/ labelling the record of cleaning carried out with white bold letter such asTANK CLEANED ON--------- (month and year), including removing creepers, vegitation and roots of plants, trees branches on or surrounding of service tank complete all as directed.Note:-(i) Unit rate quoted is deemed to be included for testing of water supply in tank both inlet and outlet flow during next supply hours early in the morning or late in evening.(ii) Contractor shall maintain a pucca bound register for cleaning carried out with date and obtain users signature and remarks if any and this register to be submitted alongwith RAR.(iii)Contractor is liable to rectify any damages to the external finishes of the bldg occured during the cleaning process, i.e. scrubbing and touch up with external paints as existing specifications. Unit rate quoted is deemed too be included the cost of the same.(iv)All sort of petty T&P items such as ladder, safety equipment, nuts, bolts, washers etc. required to accomplish the job shall be provided by the contractor with out any extra cost to dept. 193 (a)For RCC /PVC tank exceeding 200 litters and not exceeding 500 ltrs 194 (b)For RCC /PVC tank exceeding 501 litters and not exceeding 1000 ltrs 195 (c)For RCC /PVC tank exceeding 1001 litters and not exceeding 2000 ltrs 196 (d)For RCC /PVC tank exceeding 2001 litters and not exceeding 5000 ltrs 197 (e)For RCC /PVC tank exceeding 5001 litters and not exceeding 25000 ltrs 198 Material and labour for preparation of old painted external surface by brooming down scrubbing with steel wire brush, scraping old distempered and painted surface and applying two coat of cement base paint to service tanks in building and under ground sump/ RCC Tanks all specified for tanks capacity of 200 to 500 Ltrs. 199 Material and labour for preparation of old painted external surface by brooming down scrubbing with steel wire brush, scraping old distempered and painted surface and applying two coat of cement base paint to service tanks in building and under ground sump/ RCC Tanks all specified for tanks capacity 501-1000 Ltrs. 200 Material and labour for preparation of old painted external surface by brooming down scrubbing with steel wire brush, scraping old distempered and painted surface and applying two coat of cement base paint to service tanks in building and under ground sump/ RCC Tanks all specified for tanks capacity 1001-2000 Ltrs. 201 Material and labour for preparation of old painted external surface by brooming down scrubbing with steel wire brush, scraping old distempered and painted surface and applying two coat of cement base paint to service tanks in building and under ground sump/ RCC Tanks all specified for tanks capacity 2001-5000 Ltrs. 202 Taking down and relaying of existingDI water pipe lines of size 150 mm bore but of any type includings all fittings after removal of scaling, cleaning and flushing etc complete all as specified and directed.Note:Excavation & earthwork shall be measured & paid seperately 203 Taking down and relaying of existingDI water pipe lines of size 100/80 mm bore but of any type includings all fittings after removal of scaling, cleaning and flushing etc complete all as specified and directed.Note:Excavation & earthwork shall be measured & paid seperately 204 M&L as in replacement for Ductile Iron Pipe (DI Pipes), ISI marked, Class K-7, 150 mm dia laid in trenches including jointing material such as EPDM Rubber Gasket and suitable type of grease etc complete all as specified and directed.Note :- (i)DI fitting/special shall be measured and paid separately.(ii)Excavation & earthwork shall be measured & paid seperately 205 Supply and fixing in replacement Non return valve (confirming to IS-5312) (NRV) of size 150 mm ISI marked, CI body suitable for 150 mm dia pipe line complete all specified and directed 206 S&F in replacementfoot valve (confirming to IS-4038) cast iron of size 150 mm bore including rubber insertion, packing material, nuts, bolts, and washer with suitable new one all as specified and directed. 207 Supply and fixing in replacement Sluice valve of size 150 mm dia Cl body, both ends flanged duly drilled, ISI marked with IS-14846-2000, PN-1.6 having Stainless Steel spindle and check nut including operating wheel, fixing with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed. 208 Material and Labour for dismantling the brassspindle from 150 mm dia bore sluice valves in various locations and reconditioning the sluice valve by replacing SS/bronze spindle, spindle nuts with brass ring, gland nuts complete all as specified and as directed. 209 Material and Labour for gland packing in leaking Sluice Valves of 150 mm dia size Complete including replacing/tightening the existing bolts and nuts etc. complete all as directed . 210 Material and Labour for Cutting DI pipes in position for insertion of new tees and socket of size 150 mm dia Complete all as specified and as directed. 211 Supply and fixing in replacement butterfly valve(confirming to IS-13095) of size 150 mm dia Cl body, ISI marked with IS-13095 having double door convex shape to prevent eddies and reaches head loss, neoprene rubber sealing and fitted complete all specified and directed 212 Cutting the existing broken / cracked CI/DI/GI/Asbestos Cement Pipe line of size upto 150mm dia, by dewatering the lekage water from site and removing the old pipe line and addition / alteration to pipe by providing new pipe,welding,bending,grinding,including all accessories such as tee,elbow,collar etc , and ensure any leakage with pressure test complete all as specified and as directed.Note : Pipes and mechanical collar shall be measured and paid seperately 213 M&L for specials fittings suitable for Cast iron / ductile iron /Asbestos cement pipe made out of MS Plate of 12 mm thick complete with mechanical/detachable type arrangement as per site requirementwith MS bolts and nuts of suitable size and MS sheet fabricated to required dia of pipe for prepration of collar/flange, on any pipe leak or cracks of pipe for arresting the leakage complete including rubber ring, packing rubber sheet,set of two collar rings of size 150 mm borecomplete all as specified and as directed. 214 M&L as in replacement for Ductile Iron Pipe (DI Pipes), ISI marked, Class K-7, 100 mm dia laid in trenches including jointing material such as EPDM Rubber Gasket and suitable type of grease etc complete all as specified and directed.Note :- (i)DI fitting/special shall be measured and paid separately. (ii)Excavation & earthwork shall be measured & paid seperately 215 Supply and fixing in replacement Non return valve (confirming to IS-5312) (NRV) of size 100 mm ISI marked, CI body suitable for 100 mm dia pipe line complete all specified and directed 216 S&F in replacementfoot valve (confirming to IS-4038) cast iron of size 100 mm bore including rubber insertion, packing material, nuts, bolts, and washer with suitable new one all as specified and directed. 217 Supply and fixing in replacement Sluice valve of size 100 mm dia Cl body, both ends flanged duly drilled, ISI marked with IS-14846-2000, PN-1.6 having Stainless Steel spindle and check nut including operating wheel, fixing with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed. 218 Material and Labour for dismantling the brass spindle from 100 mm dia bore sluice valves in various locations and reconditioning the sluice valve by replacing SS/bronze spindle, spindle nuts with brass ring, gland nuts complete all as specified and as directed. 219 Supply and fix replacement ofleather packing suitable for foot valve 80 to 100 mm dia, suction pipe flanged connected to pumpsets including replacement ofnuts and bolts etc all as specified and directed 220 Material and Labour for gland packing in leaking Sluice Valves of 100 mm dia size Complete including replacing/tightening the existing bolts and nuts etc. complete all as directed . 221 Material & Labour as in repair for Construction ofValve pit having inner dimensions 900 mm x 900 mm x 900 mm with foundation PCC 1:4:8 type D2 using 40mm grade stone aggregate, brick work with sub class B old size built in Cement mortar 1:6, PCC 1:2:4 type B1 using 20mm stone aggregate for Coping, 15 mm thick rendering plaster in CM 1:4 inluding MS cover with locking arrangement all as specified and as directed.Note :- MS work as in Chamber Covers shall be measured and paid separately under relevant item of this schedule. 222 Material and labour for Fabricate supply and fix valve chamber coversmade out of suitable size MS angle/MS plate/flat/rod, hinges, locking arrangement including painting with two coats of synthetic enamel paint over one coat of red oxide primer including removimg existing unserviceable rusted cover all as directed. 223 Material and labourfor Painting with two coats of synthetic enamel paint over a coat of zinc chrome on surfaces of any description, over 10cm in width or girth,not otherwise described complete all specified and directed. 224 Material and labourCleaning of valve pit chamber for sluice/gate valve of 50/80/100/150/200/ size by removing mud/ grass/ sludge/ other waste materialsfrom the chamber and from surroundings upto 1mtr distance, carryout petty cement repairs with cement mortar 1:4, apply one coat of white wash on cemented surfaces and one coat of synthetic paint on steel surfaces complete to make an operator friendly valve chamber complete as specified and directedNote :- Periodicity and locations of valve chambers shall be given as per requirement by the Engineer-in-Charge. 225 Cutting the existing broken / cracked CI/DI/GI/Asbestos Cement Pipe line of size upto 100mm dia, by dewatering the leakage water from site and removing the old pipe line and addition / alteration to pipe by providing new pipe,welding,bending,grinding,including all accessories such as tee,elbow,collar etc , and ensure any leakage with pressure test complete all as specified and as directed.Note : Pipes and mechanical collar shall be measured and paid seperately 226 M&L for specials fittings suitable for Cast iron / ductile iron /Asbestos cement pipe made out of MS Plate of 12 mm thick complete with mechanical/detachable type arrangement as per site requirementwith MS bolts and nuts of suitable size and MS sheet fabricated to required dia of pipe for prepration of collar/flange, on any pipe leak or cracks of pipe for arresting the leakage complete including rubber ring, packing rubber sheet,set of two collar rings of size 100 mm borecomplete all as specified and as directed. 227 Supply and Fixing as in replacement MCCB, 4 poles 415 Volts, 100 Amps, 16 KA, 50 Hz, AC, adjustable thermal and magnetictype in the existing pump starter panel including connecting up incoming/out going cable with suitable lugs and testing complete all as specified and as directed.Make : Legrand/Indo asian/L&T 228 M&L as in replacement for Ductile Iron Pipe (DI Pipes), ISI marked, Class K-7, 80 mm dia laid in trenches including jointing material such as EPDM Rubber Gasket and suitable type of grease etc complete all as specified and directed.Note :- (ii) DI fitting/special shall be measured and paid separately. (i)Excavation & earthwork shall be measured & paid seperately 229 M & L for DI specials and fittings as per IS for spigot and socketed pipes or flanged pipe for water mains branch lines such as bends(any type radious and angle ) tapers any type (straight, bend,increasing,decresing,or double socket etc) tee pices,single branch,Y juntion, double branch, cross, including connecting pieces one end flanged and other socket or spigot and bell mouth pices suitable for rubber joint,tyton joint up to 150 mm bore and conforming to IS-9523: 2000 complete all as specified and directed. 230 Note :-(a) In case of laying of CI/GI/DI pipe line is to be executed in civil area, it will be the responsibility of the contractor to obtain necessary permission for cutting of road & berm from BWSSB. 231 (b) For this purpose amount to be paid online to BWSSB, same is deemed to be included in unit quoted rate. 232 (c) The T&P like JCB, Drill Machine, Moveable Generator etc required for cutting of road shall be arranged by the contractor & no extra cost shall be paid for the same. 233 (d) After execution of work, the contractor will make good disturbed portion of road with bitumen or PCC complete as directed by Engineer-in-Charge. Cost of the same is deemed to be included in unit quoted rate. 234 Supply and fixing in replacement Sluice valve of size 80mm dia Cl body, both ends flanged duly drilled, ISI marked with IS-14846-2000, PN-1.6 having Stainless Steel spindle and check nut including operating wheel, fixing with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed. 235 Material and Labour for dismantling the brass spindle from 80 mm dia bore sluice valves in various locations and reconditioning the sluice valve by replacing SS/bronze, spindle nuts with brass ring, gland nuts complete all as specified and as directed. 236 Material and Labour for gland packing in leaking Sluice Valves of 80 mm dia size Complete including replacing/tightening the existing bolts and nuts etc. complete all as directed . 237 S&F in replacementfoot valve (confirming to IS-4038) cast iron of size 80 mm bore including rubber insertion, packing material, nuts, bolts, and washer with suitable new one all as specified and directed. 238 Supply and fixing in replacement Non return valve (confirming to IS-5312) (NRV) of size 80 mm ISI marked, CI body suitable for 80 mm dia pipe line complete all specified and directed 239 Supply and fixing in replacement Non return valve (confirming to IS-5312) (NRV) of size 65 mm ISI marked, CI body suitable for 65 mm dia pipe line complete all specified and directed 240 Material and Labour for Cutting DI pipes of size 200/150/100/80 in position for insertion of new tees and socket of size15/20 mm dia Complete all as specified and as directed. 241 Material and Labour for Plain Cement Concrete (1:2:4), type B1 (using 20 mm graded crushed stone aggregate) as in Coping, bands benching etc including finishing the concrete surfaces even and smooth without using extra cement including necessary form work Complete all as specified and directed. 242 Supply and fixing in replacement of Air Release Valve of size 40 mm dia Cl body, ISI marked of IS 14845 of 1.6 PNincluding fixing arrangement of existing 150 mm dia DI pipe line with new nuts, bolts, washers and rubber insertion/packing complete all specified and directed. 243 Making arrangement to flush out the existing pipe line of any type upto 50mm bore and upto 100m length, applying 4.5 N/sqmm pressure to remove scalings/ sludges/ other blocking materials to make smooth flow of water including testing all as specified and directed. 244 Making arrangement to flush out the existing pipe line of any type 63 to 100 mm bore and upto 100m length, applying 4.5 N/sqmm pressure kg/sq cm pressure to remove scalings/ sludges/ other blocking materials to make smooth flow of water including testing all as specified and directed. 245 Material and labour for Making arrangement to flush out the existing pipe line of any type 110 to 150mm bore and upto 100m length, applying 4.5 N/sqmm pressure to remove scalings/ sludges/ other blocking materials to make smooth flow of water including testing all as specified and directed. 246 Material and labour for Making arrangement to flush out the existing pipe line of any type 160 to 200 mm bore and upto 100m length, applying 4.5 N/sqmm pressure to remove scalings/ sludges/ other blocking materials to make smooth flow of water including testing all as specified and directed. 247 Note for item 243 to 246 :-(i)The Contractor is deemed toarrange necessary tools and equipments, removing or alteration of fittings from existing pipe lines, arragement of plugging devices, etc to build up specified pressure required to wash out the pipes. This will be inclusive in quoted rate. (ii)Excavation and earth work required shall be measured and paid seperately. (iii)The flushing out shall be carried out with fresh filled water of well only duly chlorinated with specified sodium hypochlorite solution to disinfect the pipe lines from all pathogens and Coliform organisms.This will be inclusive in quoted rate. 248 Material and labour for dewatering & Cleaning ofRCC Over Head Tanks of the followingcapacities by comprisingof the followings 09 (NINE) stage of cleaning process complete all as specified and directed:-(i)De-watering by high pressure submersible pump all complete (Notes for item No 249 to 261) :- The Bidder shall take into consideration for following points while quoting his rate for this item andthe unit rate is deemed to be included for :-(i) The contractor shall provide dewatering pump of suitable capacity and mobile generatorfor operation of dewatering by high pressure submersible pump (or) Diesel driven high pressure pump and the rate quoted is inclusive of rent/hiring charges complete. (ii) Cuttingand filling, cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Useful material shall be stacked.(iii) Material removed from the tank shall be disposed off to out side MD land.(iv) Tank shall be made available for cleaning for a period of 8 hours only and contractor has to arrange sufficient labour/ T&P to complete the job with the given period only. or otherwise penalty shall be imposed @ Rs 500/- per day.(v) All safety gadgets like safety Belts, special safety ladder, Helmets, Heavy Duty Gum Boots,Gloves, Safety Goggles, Masks, Aprons, etc. for complete security safe operations, Storage and Cleaning equipment’s like Scrubbers/Wipers, Storage drums, Sludge Collectors and Cisterns, etc. must be integral part of system. (vi) Removal of sludge fromRCC Over Head Tanks(vii)Cleaning of walls, floors, ceiling etc by high pressure jet pump 80-180 bar pressure all complete(viii)Removing dirt and sludge by vacuum pump(ix) Anti- Bacterial Treatment of inside of tank effective againstall pathogens all complete.(x) Sterilization of the tank atomosphere by UV radiation inside of the tank.(xi) Applying one coat of white wash to internal surfaces.(xii)Replace nylon net for vent pipes &man hole cover(xiii)Writing letter in bold with white paint on black colour back ground such as sump number, capacity, cleaned on Date & Due on Date etc 249 250000 gallon capacity22 Mt heightat ETI Tank 250 150000 gallon capacity22 Mt heightat Bhatiya tank 251 150000 gallon capacity15 Mtr height at GLR 1 and GLR 2 Double tank 252 150000 gallon capacity12.5 Mtr height at IMH Area 253 150000 gallon capacity22 Mt height at E&ITI Tank 254 100000 gallon capacity 18 Mtr height at Bhatia tank,West 255 75000 gallon capacity 18 Mtr height at Umbrella tank 256 50000 gallon capacity18 Mtr height at Domestic Area 257 30000 gallon capacity25 Mtr height at CE Complex 258 25000 gallon capacity16 Mtr height at MAP, 54 Civ. 259 25000 gallon capacity18 Mtr height at Double tank168 WO 260 20000 gallon capacity12 Mtr height at Height at KV School 261 20000 gallon capacity12 Mtrheight at 90 CIV Pump House 262 M & L for Fixing in repairs Water Level Indicator consisting of float ball, nylon rope, Scale for water level indication made out of MS frame with pulley and indicating pointer for OHT at different places all as specified and directed . 263 Supply and fixing as in repair for aluminium earth continuity conductor or main earthing lead fixed to wall /roof top for lightning arresterfixed to OHT or other indicated situation for loop earthing etc. as required for 25 mm x 3 mm thick, aluminium using porcelain clit/post insulators with screw / selfdril GIscrew with rubber washer , complete all as specified and directed. 264 Supply and fix as in repair TPN MCB ,415 volts,fixed type ,40 Amp, 50 Hz, with rupturing capacity 10 KA in theexisting pump starter panel including connecting up incoming/out going cables with suitable lugs and testing complete all as specified and as directed. Make: Indoasian/L&T/ Legrand 265 S&F as in repair single core multistrand flexible copper cable of size 35 Sqmm x 1 core , includinglugs , connecting up with nuts and bolts, insulation tape wrappingetc , the selection of cable as per colour code all as specified and directed Make : Havells /Polycab/RPGAsian 266 Excavation in trenches not exceeding 1.5 mtr in width and not exceeding 1.5 mtr in depth for laying of cables up to proper level and laying of pipelines etcinany type of soil, complete all as specified and directed. 267 Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick, complete all as specified and directed. 268 Removing surplus excavated material (soil) not exc 50 meter and depositing where directed at a level not exc 1.5 meter above the starting point, complete all as specified and directed. 269 Material and labour for Spreading ribbed soil in trenches as in cable cushioning all as per IS 1255-1983, complete all as specified and directed.Note :- (i)Excavated approved soil shall be ribbed by using sieve to separate composite particles etc. as per IS and refilling in trenches before laying of cable 8 CM and 15 CM after laying of cable. This is then gently punned down to a depth of 10 cm above the top of upper most cable (ii) For the purpose of measurement only punned thickness shall be considered for payment. 270 Material and labour for well burnt bricks ‘B’ class as mechanicalprotection to under ground cables laying with length of the bricks equal to the width of the trench, complete all as specified and directed. 271 Material and labour for Cutting existing road/PCC/Drain for laying of GI or any type of pipe including necessary earthwork, excavation exc 600mm depth but not exc 1mtr depth, 800 mm wide including making good existing surface with 150 mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate, complete all as specified and directed. Note :-The tenderer shall take into consideration for following points while quoting rate for this item andthe unit rate is deemed to be inclusive for :-(i) Earth work and excavation in any type of soil(ii) Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick complete all as specified and as directed.(iii) Removing excavated material to out side MD.(iv)Laying of any type/any bore of pipe in trenches including taking down. Supply of pipe shall be measured and paid separately(v)150 mm thickPCC 1:2:4 type B1 using 20mm graded stone aggregate as inroad to make good existing disturbed surfaces. 272 Boring of holes under road, pavement, hard standing by trenchless technology using ultra sounding technique and necessary machine including HDPE pipe of 100 mm dia suitable for 0.4 mpa working pressure. 273 Material and labour in repair for 3 ½ core 70 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make:- Havells/ Polycab/ RPG Asian Note - Earthwork and bricks to be paid separately in respective items. 274 Material and labour in repair for 3 ½ core 50 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make:- Havells/ Polycab/ RPG Asian Note - Earthwork and bricks to be paid separately in respective items. 275 Supply, installation, commissioning and testing of factory assembled, floor mounted, free standing type tested LT Feeder pillar panel, with canopy, as per electrical specifications for outdoor installation to be made of IP65 Polycarbonate modular enclosures. The enclosures made of polycarbonate, should be weather/vermin proof, anti -acid, anti-corrossive, UV resistance in accordance with IEC 61439-1, fire retardant and self extingushing in accordance with IEC 60695-2-11, UL subject 94 for flammability V-0, should pass glow wire test for 960 degree in accoardance with 60695-2-11.Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262,IP65 in accordance with IEC-60529 and IEC- 60439-1, should have dielectric properties, RoHS compliants & Halogen free. The manufacturer of boards/panels shall submit a copy oftype test reports as per above mentioned norms either from UL/ERDA/CPRI/NABL labs in india.The panel should be modular and compartmentalized in construction with opaque and transparent doors, properly tightened to base with thermoplastic screws having sealing gaskets of extruded silicon rubber to withstand adverse weather effects. The depth of modular enclosure should be minimum 200mm for air circulation & to minimize temp rise. Panel should be fitted with one No.polycarbonate IP 65, 9 W LED translucent bulk head luminaire color lamp not less than 6500K, PF >0.95 under canopy for easy maintenance. Panel shall be fitted outside with one No of 16 Amp 3 Pole IP65 industrial socket and 01 No. of 32Amp 5P IP 65 industrial socket. 3 Phase and neutral 630 Amp current carrying capacity of aluminium bus bar insulated with colour coded heat shrinkable sleeves with SMC/DMC insulators,complete with the following switch gears and mounting the panel board on ground with PCC (1:3:6) type C-1 using 20mm graded aggregate forbedding upto a height of 45 CM above ground level, including dismanting and taking out old U/s LT panel board and reconnecting existing LT UG Cable with new panel board amplete all as specified and all as directed and comprising of the following:- 276 (a) ON load change over switch 4 Pole, 415 V of capacity 400 Amp, 36 KA - 01 No. (b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity400 Amp,36 KA- 02 Nos.(c) Multifunction Meter (V,I,PF) with suitable capacity of CTs- 01 No(d) Indicating lamp (R-Y-B) set LED type with backup MCB for 3 Phase Supply - 01 set. (e) Space for spare feeder - 01 No. Note :-(i) The Contractor shall submit the drawing for approval of GE before executing the work.(ii) Insulators, bus bar sleeves, lugs, gland etc including complete wiring with suitable size of copper wire are all inclusive in unit quoted rate. (iii) Make of Switch gear : Schneider/L&T/C&S.(vi) MCCB should be ICu =100% ICs.(v) Make of LT Panel/FPB shall be as mentioned in list of makes (PS). 277 Supply, installation, commissioning and testing of factory assembled, floor mounted, free standing type tested LT Feeder pillar panel, with canopy, as per electrical specifications for outdoor installation to be made of IP65 Polycarbonate modular enclosures. The enclosures made of polycarbonate, should be weather/vermin proof, anti -acid, anti-corrossive, UV resistance in accordance with IEC 61439-1, fire retardant and self extingushing in accordance with IEC 60695-2-11, UL subject 94 for flammability V-0, should pass glow wire test for 960 degree in accoardance with 60695-2-11.Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262,IP65 in accordance with IEC-60529 and IEC- 60439-1, should have dielectric properties, RoHS compliants & Halogen free. The manufacturer of boards/panels shall submit a copy oftype test reports as per above mentioned norms either from UL/ERDA/CPRI/NABL labs in india.The panel should be modular and compartmentalized in construction with opaque and transparent doors, properly tightened to base with thermoplastic screws having sealing gaskets of extruded silicon rubber to withstand adverse weather effects. The depth of modular enclosure should be minimum 200mm for air circulation & to minimize temp rise. Panel should be fitted with one No.polycarbonate IP 65, 9 W LED translucent bulk head luminaire colour lamp not less than 6500K, PF >0.95 under canopy for easy maintenance. Panel shall be fitted outside with one No of 16 Amp 3 Pole IP65 industrial socket and 01 No. of 3 2Amp 5P IP 65 industrial socket. 3 Phase and neutral 400 Amp current carrying capacity of aluminium bus bar insulated with colour coded heat shrinkable sleeves with SMC/DMC insulators,complete with the following switch gears and mounting the panel board on ground with PCC (1:3:6) type C-1 using 20mm graded aggregate forbedding upto a height of 45 CM above ground level, including dismanting and taking out old unserviceable LT panel board and reconnecting existing LT UG Cable with new panel board complete all as specified and all as directed. This comprising of the following:- 278 (a) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 200 Amp, 25 KA - 01 No (Incomer). (b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity63 Amp,10 KA- 05 Nos (OG).(c) Multifunction Meter (V,I,PF) with suitable capacity of CTs- 01 No(d) Indicating lamp (R-Y-B) set LED type with backup MCB for 3 Phase Supply - 01 set. (e) Space for spare feeder - 01 No. Note :-(i) The Contractor shall submit the drawing for approval of GE before executing the work.(ii) Insulators, bus bar sleeves, lugs, gland etc including complete wiring with suitable size of copper wire are all inclusive in unit quoted rate. (iii) Make of Switch gear : Schneider/L&T/C&S.(vi) MCCB should be ICu =100% ICs.(v) Make of LT Panel/FPB shall be as mentioned in list of makes (PS). 279 Supply, installation, testing & commissioning of maintenance free chemicalearthing system comprising of 17mm dia copper bondedrod 3 mtr long horizontally pre welded T-terminal rod with provision for connection size of 50 x 150mm long, 6mm thickness with equal space either side, with 12mm dia hole of 02 numbers each on either side of the terminal clamp with 250 microns (average) coating thickness, tested and certified by CPRI India alongwith 50 Kg earth energizer compound and 10 litres earth resistance reducingliquid. The earthing energizer compound and resistance reducing earthing liquid shall be tested as per IEC-62561-7 read with ASTM G57-06, CI 3.4 A by any NABL accredited lab. The above mentioned rod shall be installed in 4-6 inch bore, 12 feet depth with a distance of minimum 3 meters between each installation including taking down existing one, complete all as specified and directed..Make : Model HTSP 317 of safeTrode or equivalent in Snaga/ Cubes 6 Global 280 The quoted rate shall also deemed to be included the following :- (i)Prior toinstallation of maintenance free chemicalearthing, soil resistivity test to be carried out at the location where earthingwork to be donein presence of Engr-in- Charge/JE (E/M),user and the report has tosubmitto Garrison Engineer with recommendation of manufacturer, if required additional interconnection ofearthing (not more than 08 number of earthing) to achive earth result less then 1 Ohms. The arrangement done for soil resistivity testingandsubmission of report with recommendationdeemed to be included in the quoted rate. 281 (ii) The description/ size/ qty of items mentioned in above are for indicating only however qty/ size may vary at site condition to maintain the earth resistance 1 ohm. The contractor shall quote rate by considering all factors. 282 (iii) Rateofearth energizer compound of 25 Kg of 02 bags and earthresistance reducingliquid 10 litre per cane for each pit deemed to be included in the quoted rate. 283 (iv)Resistivity of earth energizer compound and resistance reducing earthing liquid shall be certified by any NABL accredited lab carried out as per IEC-62561-7 read with ASTMG57-06, CI-3.4A and the certificate of same shall be submitted by the contractor along with the sample approval 284 (v) Earth enhancing material should not leach into the adjacent soil or underground water channels and its PH value should be in neutral range complete all as specified and as directed. It should solidify when mixed with water and set like concrete. 285 (vi) Copper strip of size 20 x 3 mm shallbe fixed on proper post insulator at the instrument end (copper strip upto 7.5 RM shall be considered in unit quoted rate and extra will be measured and paid separately). 286 (vii)Testing of earth shall be carriedout in presence ofdepartmental and user representativeand report shall be submitted to Garrison Engineer duly signed by all concerned. 287 (viii)Earth resistance tester will be provided by the contractor.Tester should be calibrated from authorised company/ lab. 288 (ix)Earthing shall be tested after completion of work by the contractor in presence of Engr-in-charge, user and proper record shall be maintained duly signed by all concerned.After testing if the desired earth resistance of less than 1 Ohm is not obtained, the earthing will be redone at no extra cost to Govt. till desired result is obtained. 289 (x) The contractor shall give a written guarantee of minimum three years for maintaining the earth resistance less than 1 Ohm after certified date of completion. 290 (xi) No further maintenance or periodic watering or recharge shall be required in earthing during its guarantee period of over 03 years in all type of soil including soft/ disintegrated or hard rock. 291 (xii) During the guarantee period, if earth resistance is not maintained less than 1 ohm the contractor has to redo or rectify at no extra cost to Govt till desired result is maintained. 292 (xiii) A security deposit of value equal to 2.5 % of the rate quoted for chemical earthing for each earthing shall be retained from payment due to the contractor from final bill for the guarantee period. 293 (xiv) The electrode shallcarry manufacturers name . 294 (xv) The connection clamp shall be permanentlly welded to the copper boundedrodto avoid any kind of connectivity loss,.The pre-welded copper bounded rod shall not need any additional clamp for termination. 295 (xvi) The acceptable earth resistance at earth busbar/ test point shall not be more than 0.1 ohm. 296 (xvii)Earth work such as auguring andmaking good the surrounding area shall carried out in any type of soil. 297 (xviii)The contractor shall submit CPRI India certified document for copper bounded rod to ensure genuineness of material. 298 (xix) Sign boardof mild steel sheet 2 mm thick duly painted with two coats of synthetic enamel paint over a coat of red oxideZinc chrome primer showing result of earthing shall be fixed near the earth pit after completion as directed by engr -in- charge. 299 Material and labour for Earth pit cover madeof heavy duty poly plastic of high grade polypropylene tested and certified by any NABL accredited lab for load bearing capacity not less than 7.2 tonnes with top dia not less than 250mm, bottom dia not less than 330 mm and height not less than 260 mm for each electrode pit complete including taking down old unserviceable pit cover of any decription all as specified and directed.Make : Model SEPC 250 of SAFE TRODE or equivalent in Snaga/ Cubes 6 Global 300 S&F in repair copper strip 20 x 3mm thick as earthing lead fixed to wall/roofs etc including taking down existing old unserviceable copper strip etc, complete all as specified anddirected. Note : - All Joints should be joined by Exothermic Welding or Brazing. 301 Supply and fix for GI pipe light grade 50 mm dia for cable protection on road crossings /plinth protection with fixed to the pole wall etc along withsuitable fittings for cable protection etc complete all as specified and directed. 302 Material and labour in repair for3 ½ core 25 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make:- Havells/ Polycab/ RPG Asian Note - Earthwork and bricks to be paid separately in respective items. 303 Material and labour in repair for 4 core 10 Sqmm XLPE insulated heavy duty electric cable with aluminium multi stranded conductor 1100 volts grade served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall sheathed laying in trenches/cable ducts, fixed to wall/pole, complete all as specified and directed. Make:- Havells/ Polycab/ RPG Asian Note - Earthwork and bricks to be paid separately in respective items. 304 Supply, installation, commissioning and testing of factory assembled, floor mounted, free standing type tested LT Feeder pillar panel, with canopy, as per electrical specifications for outdoor installation to be made of IP65 Polycarbonate modular enclosures. The enclosures made of polycarbonate, should be weather/vermin proof, anti -acid, anti-corrossive, UV resistance in accordance with IEC 61439-1, fire retardant and self extingushing in accordance with IEC 60695-2-11, UL subject 94 for flammability V-0, should pass glow wire test for 960 degree in accoardance with 60695-2-11.Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262,IP65 in accordance with IEC-60529 and IEC- 60439-1, should have dielectric properties, RoHS compliants & Halogen free. The manufacturer of boards/panels shall submit a copy oftype test reports as per above mentioned norms either from UL/ERDA/CPRI/NABL labs in india.The panel should be modular and compartmentalized in construction with opaque and transparent doors, properly tightened to base with thermoplastic screws having sealing gaskets of extruded silicon rubber to withstand adverse weather effects. The depth of modular enclosure should be minimum 200mm for air circulation & to minimize temp rise. Panel should be fitted with one No.polycarbonate IP 65, 9 W LED translucent bulk head luminaire color lamp not less than 6500K, PF >0.95 under canopy for easy maintenance. Panel shall be fitted outside with one No of 16 Amp 3 Pole IP65 industrial socket and 01 No. of 32Amp 5P IP 65 industrial socket. 3 Phase and neutral 400 Amp current carrying capacity of aluminium bus bar insulated with colour coded heat shrinkable sleeves with SMC/DMC insulators,complete with the following switch gears and mounting the panel board on ground with PCC (1:3:6) type C-1 using 20mm graded aggregate forbedding upto a height of 45 CM above ground level, including dismanting and taking out old U/s LT panel board and reconnecting existing LT UG Cable with new panel board amplete all as specified and all as directed and comprising of the following:- 305 (a) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 250 Amps, 25 KA- 01 No (Incomer).(b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 160Amps, 25 KA- 01 Nos.(c) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 63Amps, 10 KA- 01 Nos.(d) Multifunction Meter (V,I,PF) with suitable capacity of CTs- 01 No.(e) Indicating lamp (R-Y-B) set LED type with backup MCB for 3 Phase Supply - 01 set.(f) Space for spare feeder - 01 No. Note :-(i) The Contractor shall submit the drawing for approval of GE before executing the work.(ii) Insulators, bus bar sleeves, lugs, gland etc including complete wiring with suitable size of copper wire are all inclusive in unit quoted rate. (iii) Make of Switch gear : Schneider/L&T/C&S.(vi) MCCB should be ICu =100% ICs.(v) Make of LT Panel/FPB shall be as mentioned in list of makes (PS). 306 Supply, installation, commissioning and testing of factory assembled, floor mounted, free standing type tested LT Feeder pillar panel, with canopy, as per electrical specifications for outdoor installation to be made of IP65 Polycarbonate modular enclosures. The enclosures made of polycarbonate, should be weather/vermin proof, anti -acid, anti-corrossive, UV resistance in accordance with IEC 61439-1, fire retardant and self extingushing in accordance with IEC 60695-2-11, UL subject 94 for flammability V-0, should pass glow wire test for 960 degree in accoardance with 60695-2-11.Degree of protection against mechanical load should be IK08 (5 Joule) in accordance with IEC 62262,IP65 in accordance with IEC-60529 and IEC- 60439-1, should have dielectric properties, RoHS compliants & Halogen free. The manufacturer of boards/panels shall submit a copy oftype test reports as per above mentioned norms either from UL/ERDA/CPRI/NABL labs in india.The panel should be modular and compartmentalized in construction with opaque and transparent doors, properly tightened to base with thermoplastic screws having sealing gaskets of extruded silicon rubber to withstand adverse weather effects. The depth of modular enclosure should be minimum 200mm for air circulation & to minimize temp rise. Panel should be fitted with one No.polycarbonate IP 65, 9 W LED translucent bulk head luminaire color lamp not less than 6500K, PF >0.95 under canopy for easy maintenance. Panel shall be fitted outside with one No of 16 Amp 3 Pole IP65 industrial socket and 01 No. of 32Amp 5P IP 65 industrial socket. 3 Phase and neutral 600 Amp current carrying capacity of aluminium bus bar insulated with colour coded heat shrinkable sleeves with SMC/DMC insulators,complete with the following switch gears and mounting the panel board on ground with PCC (1:3:6) type C-1 using 20mm graded aggregate forbedding upto a height of 45 CM above ground level, including dismanting and taking out old U/s LT panel board and reconnecting existing LT UG Cable with new panel board amplete all as specified and all as directed and comprising of the following:- 307 (a) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 400 Amps, 36 KA- 01 No (Incomer).(b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 200Amps, 25 KA- 01 No.(b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 160Amps, 25 KA- 03 Nos.(b) MCCB with thermal magnetic release 4 Pole, 415 V of capacity 63 Amps, 10 KA- 02 No(c) Multifunction Meter (V,I,PF) with suitable capacity of CTs- 01 No.(d) Indicating lamp (R-Y-B) set LED type with backup MCB for 3 Phase Supply - 01 set.(e) Space for spare feeder - 01 No. Note :-(i) The Contractor shall submit the drawing for approval of GE before executing the work.(ii) Insulators, bus bar sleeves, lugs, gland etc including complete wiring with suitable size of copper wire are all inclusive in unit quoted rate. (iii) Make of Switch gear : Schneider/L&T/C&S.(vi) MCCB should be ICu =100% ICs.(v) Make of LT Panel/FPB shall be as mentioned in list of makes (PS). 308 Material and labour for dewatering & Cleaning of RCC UG sumps of the followingcapacities by comprisingof the followings 09 (Nine) stage of cleaning process complete all as specified and directed(i)De-watering by high pressure submersible pump complete (Note for item No 309 to 316 :-The Bidder shall take into consideration for following points while quoting his rate for these items andthe unit rate is deemed to be included for :-(i) The contractor shall provide dewatering pump of suitable capacity and mobile generatorfor operation of dewatering by high pressure submersible pump (or) Diesel driven high pressure pump and the rate quoted is inclusive of rent/hiring charges complete. (ii) Cuttingand filling cleared of shrubs, vegetation, grass bush, weed, trees and sapling not exceeding 30 cm in girth, measured at a height of two metre above ground level. Useful material shall be stacked.(iii) Material removed from the tank shall be disposed off out side MD land.(iv) Tank shall be made available for cleaning for a period of 8 hours only and contractor has to arrange sufficient labour/ T&P to complete the job with the given period only. or otherwise penality shall be imposed @ Rs 500/- per day.(v) Removal of sludge from sump(vi)Cleaning of walls, floors, ceiling etc by high pressure jet pump 80-180 bar pressure all complete(vii)Removing dirt and sludge by vaccum pump(viii) Anti- Bacterial Treatment of inside of tank is effective againstall pathogens all complete.(ix) Sterilization of the tank atomosphere by UV radiation inside of the tank.(x) Applying one coat of white wash internal surfaces.(xi)Replace nylon net for vent pipes &man hole cover(xii)Writing letter in bold with white paint on black colour back ground such as sump number, capacity, cleaned on Date & Due on Date etc 309 Underground sump of capacity 200000 gallon at Range pump house. 310 Semi underground sump of capacity 200000 gallon at Ayyappa Temple/ pump house. 311 Semi underground sump of capacity 120000 gallon at Service tank Pump house 312 Underground sump of capacity 50000 gallon at Gurukul 313 Semi underground sump capacity of 50000 at AFTC Pump House 314 Underground sump of capacity50000 gallon at AFTC Pump House, range pump house 315 Underground sump of capacity 20000 gallon at 91 CIV Pump house 316 Underground sump of capacity 10000 gallon at CE Complex/ pump house 317 M & L for Fixing in repairs Water Level Indicator consisting of float ball, nylon rope, Scale for water level indication made out of MS frame with pulley and indicating pointer for UG sumpat different places all as specified and directed . 318 Cleaning of UGopen static Water Tank (SWT) of the followingcapacities by comprisingof the followings 07 (Seven) stage of cleaning process for the undermentioned capcities complete all as specified and directed:-(i)De-watering by high pressure submersible pump all complete (ii) Removal of sludge/mud/silt/sand from sump and disposal out side MD land(iii)Cleaning of walls, floors, ceiling etc by high pressure jet pump 80-180 bar pressure all complete(iv)Removing dirt and sludge by vacuum pump(v) Applying one coat of white wash internal surfaces.(vi)Replace nylon net for vent pipes &man hole cover(vii)Writing letter in bold with white paint on black colour back ground such as sump number, capacity, cleaned on Date & Due on Date etc Note : The contractor shall arrange mobile generatorfor operation of dewatering by high pressure submersible pump (or) Diesel driven high pressure pump and the unit quoted rate is inclusive of rent/hiring charges complete. 319 20000 Gallons capacity at ETI. 320 15000 Gallons capacity at E & ITI. 321 10000 Gallons capacity near SSC. 322 S&F as in repair single core multistrand flexible copper cable of size 25 Sqmm x 1 core , includingof lugs , connecting up with nuts and bolts, insulation tape wrappingetc , the selection of cable as per colour code all as specified and directed Make : Havells /Polycab/RPGAsian 323 Material and labour for removing the submersible pump set of capacity for 7.5 to 15 HP including pipes and submersible cables complete from the exisiting bore well of depth up to 200 mtr by any suitable method i.e either manual.vehicle mounted motorized system and disconnecting the pump motor to locate the faults in presence of Engr-in-Charge, transporting to Wksp and carry out repairs, reassembling, lowering to bore well after repairs, testing and commissioning complete all as specified and directed 324 M&L for taking out, dismantling pump and motor of submersible pump set of capacity for 7.5 to 15 HP to carry out repairs and replacements , duly rewinding and replacing worn out parts, applying one coat of spray painting with synthetic enamel paint of existing colour and testing and inserting in borewell after repair complete all as specified and directed.Note :- (a)The spares shall be measured and paid seperately in the relevent items given below as supply only.(b) Cost of labour for replacement of spares and transportation are deemed to be included in the quoted rate. (c)The pumpset shall be spared for one week for repair from the date of complaint given by AGE/ JE E/M regarding breakdown. Thecontactor is responsible for making alternate arrangement of pump set in case of time required more than one week.(d)In case services affected due to delay in repair of pump set, a penalty of Rs 500 per day will be levied from the contactor.(e)Please note that this penalty is exclusively other then the condition 67 of IAFW-2249 and shall be treated as interim condition of the contract.(f)The decision of the Accepting Officer in this regard shall be final and binding. 325 Supply only GM Bush suitable for 7.5 HP to 15 HP submersible pumpset as per manufacturers design complete all as specified and as directed. 326 Supply only SS coupling bearing suitable for 7.5 HP to 15 HP submersible pumpset as per manufacturers design complete all as specified and as directed. 327 Supply only sleeve MS key for impeller suitable for 7.5 HP to 15 HP submersible pumpset as per manufacturers design complete all as specified and as directed. 328 Supply onlySand Guard suitable for 7.5 HP to 15 HP submersible pumpset as per manufacturers design complete all as specified and as directed. 329 Supply only oil seal thrust bearing suitable for 7.5 HP to 15 HP submersible pumpset as per manufacturers design complete all as specified and as directed. 330 M&L flat three core PVC Insulated & PVC Sheathed Industrial Cable for Submersible Pump Motors 1100 Volt, conforming to IS 694, 6 Sqmm nominal area complete including taking out old unserviceable cable complete all as specified and directed. Make :- Havells/Polycab/Finolex/KEI 331 S & F in repair Over load Relay range of (1.6 -2.5 Amps ) , max-10A (as per sample) for 1.5 HP starter (Dol/Star delta) complete all as directed. 332 S & F as in replacementONload change over switch 4 pole 250Amps in sheet metal enclosure complete all as specified and as directed. make :-Havells /L&T/Indo Asian 333 M & L for servicing of submersible starter by checking and servicing the contactor coil , over load relay coiland any other parts and replacement the burnt out wiring including any modification to pump starter panel by welding,cutting , grinding ,drillingtesting the panel complete all as specified and directedfor the7.5 HP to 15 HP capacity pump setsNotes :-(i) Minor spare parts such as nuts,bolts ,washers ,indicator lamps , start,stop push button and suitable size of copper wire are deemed to be included in quoted rate. 334 Supply and fix as in repair TPNMCB ,415 volts,fixed type ,63 Amp, 50 Hz, with rupturing capacity 10 KA in theexisting pump starter panel including connecting up incoming/out going cables with suitable lugs and testing complete all as specified and as directed. Make: Indoasian/L&T/ Legrand 335 S&F as in repair single core multistrand flexible copper cable of size 16 Sqmm x 1 core , including of lugs , connecting up with nuts and bolts, insulation tape wrappingetc , the selection of cable as per colour code all as specified and directed Make : Havells /Polycab/RPGAsian 336 S & F in repair Over load Relay range of (0.1 -1.5 Amps ) , max- 5A (as per sample) for 0.5 HP starter (Dol/Star delta) complete all as directed . 337 Note :- An amount of Rs 1,91,800.00 on account of credit schedule for schedule A part II shall be deducted from the total amount of BOQ to arrive at the contract sum.

BRR : 8044738 Tender For Provision Of Wksp Repair Est At Leh Under Ge I P No 1 Leh; 1 NOTE: Schedule ‘A’ Part - ItoPart -XIIare Prepriced by MES. Bidders shall insert their lumpsum amount in the Green coloured field under Col-6 only. 2 Total amount of Sch A Part - I (BUILDINGS) 3 Total amount of Sch A Part - II(SITE CLEARANCE WORKS) 4 Total amount of Sch ‘A’ Part - III (PROTECTIVE WORK) 5 Total amount of Sch ‘A’ Part - IV (ROAD WORKS) 6 Total amount of Sch ‘A’ Part - V (SEWAGE DISPOSAL WORKS) 7 Total amount of Sch ‘A’ Part - VI (SECURITY WALL WORKS) 8 Total amount of Sch ‘A’ Part - VII (INTERNAL WATER SUPPLY WORKS) 9 Total amount of Sch ‘A’ Part - VIII (INTERNAL ELECTRIC SUPPLY WORKS) 10 Total amount of Sch A Part - IX (EXTRNAL WATER SUPPLY WORKS) 11 Total amount of Sch A Part - X(EXTRNAL ELECTRIC SUPPLY WORKS) 12 Total amount of Sch ‘A’ Part - XI ( STREET LIGHT WORKS) 13 Total amount of Sch ‘A’ Part - XII ( STANDBY DG SET FOR CHS WORKS) 14 SCH A PART - XIII(Miscellaneous B/R and E/M works for Sch A Part-II to Part-XII)Note: This schedule is not pre-priced by MES and the rate indicated as Rs 0.00 under Col 5 signifies this fact only 15 Supplying and fixing30 users LLDPE septic tank designed to carry sewage and sludge water , excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft , connection etc conventional typecomplete all as specified and directed by Engrs-in-Charge. 16 Supplying and fixing 10 users LLDPE septic tank designed to carry sewage and sludge water , excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft , connection etc conventional type complete all as specified and directed by Engrs-in-Charge. 17 Construction of soakage well 2.4m internal dia and3.00m effective depth including excavation in any type of soil , foundation in PCC 1:3:6 type C-1 ( using 20mm graded crushed stone aggregates ), PCC Block honeycomb/ solid masonry in cement mortar (1:4) RCC M-30 design Mix cover Slab filled with stone boulders including intersepting chamber screen chamber and disposal of soil complete all as specified and shown on drawings. 18 Construction of soakage well 1.2m internal dia and3.00m effective depth including excavation in any type of soil , foundation in PCC 1:3:6 type C-1 ( using 20mm graded crushed stone aggregates ), PCC Block honeycomb/ solid masonry in cement mortar (1:4) RCC M-30 design Mix cover Slab filled with stone boulders including intersepting chamber screen chamber and disposal of soil complete all as specified and shown on drawings. 19 Supplying and fixing for Concertina Coil Punched type 610mm dia razor type made out of 2.50 mm dia SG hot galvanised spiring tensile wire 145 to 150 N/SQMM zinc coating 240 gms/sqmm (min) weight of coil shall be minimum 8.57 kg/coil shall be 6.25 RM after laying, min Nos of turns in each coil shall be of 49/50. Galvanized razor ribbon type shall be of size 0.50 mm thick, 19 mm side before wrapping on central core wire. Concretina coil shall be fixed to existing angle iron swan neck supports using GI clips 125 to 127 Nos per coil and special nuts and bolts for holding Z coil together and extra two rows parallel wire of 10 gauge etc all as specified. 20 M & L for MS wicket gate as Ref drwg- CELZ/TD/ST-11/2017 SHEET 1R/1 Complete all as specified and directed by Engrs-in-Charge. 21 M & L for 5.5 Mtr Wide gate with pillers Ref drwg- CELZ/TD/ST-11/2017 SHEET 1R/1 Complete all as specified and directed by Engrs-in-Charge. 22 Supply, Install, lowering, testing, and commissioning of submersible openwell pumping sets, centrifugal, electric driven,minium discharge of 23.46 LPM at 33 mtr headmotor capacity minium 3 HP including 3 HP Starter complete all specified and directed. 23 Supply, installation, testing and commissioning of LT Feeder Pillar Box, out door type, vermin proof, front dooropenable, made out of CRCA Sheet 3.15 mm thick, duly powder coated, suitable for 3 Phase4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 complete as all directed suitable for and including the following.a) Bus bar chamber with and including copper strips (set 4 nos) suitable for 100 amps duly insulated wired & duly mounted on porcelain insulators b) Incommer MCCB 4 Pole 440 Volts, 40 Amps rating with repturing capacity 16 KA - 1 Noc) Outgoing MCCB 4 Pole, 16 Amps rating with repturing capacity 16 KA - 2 No (for Openwell Submersible pumpset)d)Three Ph LED electronic Ammeter Class 1 with in built selector switch having range 0 to 100 Amp - 01 Noe) Three Ph LED electronic VoltmeterClass 1 with in built selector switch having range 0 to 500 Volts- 01 Nosf) Indicator RYB . LED type- 1 Set.g) All accessories prewired with appropriate size copper strip or wire thimbles etc. 24 h) Space for Provn of DOL starter 3 HP - 02 NosAll as required including foundations as per Manufacturers recommendations all as required at siteor as directed by Engr-in-Charge. (j) As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule. 25 Supply and fix submersible copper conductor cable 3 core, 4 sqmm 1100 volt flat industrial grade including nylon binding wire and accesories to clamp with column pipe at two places to each column pipe complete all specified and directed. 26 M&L for Construction of brick masonary valve pit of size.0.9X0.9X1.8 mtr (internal diamensions) including excavation and earth work in any type of soil, PCC 1:4:8 type B-2 in foundation brick work in CM 1:4, 15mm thick plastering in CM 1:4 internally and flush pointing externally in same mortar as the work process angle iron frame 40X40X6mm,with 3mm thick MS sheet cover with 12 mm dia handle and locking arrangement (including lock and two Keys) and two coats of synthetic enamel paint over a coat of red oxide primer, filling saw dust into the pit and providing extension rod 0.6 m long to operate sluice valve from top and welding it with sluice valve spindle all as specified and directed by Engr-in-charge. 27 Supply, installation, commissioning and testing of factory made, CPRI approved LT panel of size 1.5m x 1.2m x 0.7m, outdoor type made out of CRCA sheet 3.15 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 platform complete as all directed suitable for and including the following :- (Prop Main LT Panel)(Near Prop Transformer)(a) Copper bus bar, 3 Phase , 4 wire , AC Supply system 50 Hz mounted on epoxy based Post insulators, including drilling hole for cable connection, rating of bus bar 2400 Amps.(b) ACB 4 Pole, 415 V, with Thermal Magnetic Release (Manual Fixed type) of capacity 1600 Amps - 01 No for incoming(c) As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule. 28 (c) MCCB 4 Pole, 415 V, 36 KA, with Thermal Magnetic Release (Manual Fixed type) of capacity 630 Amps - 02 No O/G (for Prop Sub LT Panel, Spare)(d) ACB 800 Amps, 415 Volt, 36 KA, 4 Pole, thermal magnetic release - 01 No O/G (for CHS LT Panel) (e) MCCB 25 Amps, 415 Volt, 16 KA, 4 Pole, thermal magnetic release - 03 No O/G (for High Mast light No.1,2 & Feeder Pillar box)(f) Indicator Lamp LED type (RYB) - 01 Set (g) Digital type Ammeter 3 Ph with in built selector switchsuitable up to 1600 Amp including suitable rating CTs -01 Set(h) Digital type Voltmeter 3 Ph with in built selector switchsuitable up to 500 Volt- 01 Set(j) All accessories prewired with appropriate size copper strip or wire thimbles etc.All as required including foundations as per Manufacturers recommendations as directed by Engr-in-Charge. 29 Supply, installation, commissioning and testing of factory made, CPRI approved LT panel of size 1.2m x 1.2m x 0.6m, outdoor type made out of CRCA sheet 3.15 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 platform complete as all directed suitable for and including the following :- (Prop Sub LT Panel)(Near workshop bldg)(a) Copper bus bar, 3 Phase , 4 wire , AC Supply system 50 Hz mounted on epoxy based Post insulators, including drilling hole for cable connection, rating of bus bar 1000 Amps.(b) MCCB 4 Pole, 415 V, with Thermal Magnetic Release (Manual Fixed type) of capacity 630 Amps - 01 No for incoming(c) As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule. 30 (c) MCCB 250 Amps, 415 Volt, 36 KA, 4 Pole, thermal magnetic release - 01 No O/G (for VTPN DB No.1)(d) MCCB 63 Amps, 415 Volt, 25 KA, 4 Pole, thermal magnetic release - 01 Nos O/G (for VTPN DB No 2)(e) MCCB 160 Amps, 415 Volt, 25 KA, 4 Pole, thermal magnetic release - 01 Nos O/G (for VTPN DB No 3)(f) MCCB 100 Amps, 415 Volt, 16 KA, 4 Pole, thermal magnetic release - 01 No O/G (for VTPN DB No 4)(g) Indicator Lamp LED type (RYB) - 01 Set (h) Digital type Ammeter 3 Ph with in built selector switchsuitable up to 600 Amp including suitable rating CTs -01 Set(j) Digital type Voltmeter 3 Ph with in built selector switchsuitable up to 500 Volt- 01 Set(k) All accessories prewired with appropriate size copper strip or wire thimbles etc.All as required including foundations as per Manufacturers recommendations as directed by Engr-in-Charge. 31 Supply, installation, commissioning and testing of factory made, CPRI approved feeder piller box of size 0.9m x0.9m x 0.6m, outdoor type made out of CRCA sheet 3.15 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 platform complete as all directed suitable for and including fwg:- (Feeder Pillar box) (Near washing platform) 32 (a) Copper bus bar, 3 Phase , 4 wire , AC Supply system 50 Hz mounted on epoxy based Post insulators, including drilling hole for cable connection, rating of bus bar 50 Amps.(b) MCCB 25 Amps, 415 Volt, 16 KA, 4 Pole, thermal magnetic release - 01 No incomer(c) MCCB 16 Amps, 415 Volt, 16 KA, 4 Pole, thermal magnetic release - 01 No outgoing(d) Earth plug socket 3 ph 415 V, 32 Amp - 01 No(e) Switch socket combination 5/15 Amps 5/6 pin - 02 Nos(f) Indicator Lamp LED type (RYB) - 01 Set (g) Digital type Ammeter 3 Ph with in built selector switchsuitable up to 400 Amp including suitable rating CTs -01 Set(h) Digital type Voltmeter 3 Ph with in built selector switchsuitable up to 500 Volt- 01 Set(j) All accessories prewired with appropriate size copper strip or wire thimbles etc.All as required including foundations as per Manufacturers recommendations as directed by Engr-in-Charge. (k) As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule. 33 Labour for boring underground upto 100 mm bore for road crossing 3 mtr to 10 mtr not exceeding 1.5 mtr in depth for laying of electric cable and GI tubing in soft/loose soil complete all as specified. 34 Supply, Installation, Testing & Commissioning of High galvanized mast light suitable for 8 luminaries symmetrically fitted along with their control gear and having two point suspension system with stainless steel wire rope of 6 mm dia 97/19 guage and double drum winch with luminaire mounting arm, pully assembly, aviation obstruction light, lightning arrester spike including RCC foundation suitable for 12.5 Mtr height completed minimum dimension specified as under mentioned specifications.Note : As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule.(A) High Mast Structure1. Matrial of Construction:- HR sheet steel conform to IS 2062/BS EN 10025 or Equivalent2. Base Dia. and top diameter (A/F) 1. Top Section - 150 mm 2. Bottom Section - 360 mm3. Plate thickness :- Top - 3mm, Bottom - 3 mm4. Cross Section of Mast (Number of Slides) - 20 Sided Polygon5. Standard of galvanisation - As per BS EN ISO 14616. Size of opening and door at base - 1050 x 225 mm7. Diameter of base plate - 520 mm8. Thickness of base plate - 25 mm9. Lighting protection finial - G.I single spike 35 10. Max. wind speed - 50 m/s as per IS : 875 (Part -III)11. Number of foundation bolts - 4 nos12. Type/ diameter/ length of foundation bolts - TS 600/ 24 mm dia/ 850 mm long13. PCD of foundation bolts - 445 mm(B) Luminaires Carriage :- 1. Material of construction - 40 NB ERW Class B - M.S. pipe2. Diameter of carriage ring (mm) - 450 mm (ID)3. Construction - 4 Arm, welded, 2 sections4. Load Carrying capacity - 08 Luminaires(C) Trailing Cable :- 1. Conductor - Copper, 5 core, 2.5 Sqmm 2. Insulation -PVC insulated3. No of circuits per mast - One no. cable per mast (D) Winch/ Power Tool1. Type /SWL of winch - Double drum, SWL 350 Kg2. Method of seperation - Integral Motor3. Motor capacity - 0.75 HP4. No of speeds - 6 pole, single speed5. Torque limitor - with mechanical tripping facility(E) Stainless steel wire rope 1. Grade/ Construction - AISI 304, 7/19 construction2. No of ropes - Two continuous3. Diameter (mm) - 5 mm4. Breaking load capacity - 1350 Kg x 2 36 S&F Vertical TPN Loadline distribution board iron clad, doube door with IP-43 1K-09 protection suitable for MCCB as incomer and MCB as ougoing 415 Volts 3 phase 50 C/s 8 way, complete with appropriate size copper bus bar and neutral link, confirming to Cat Pt No DHDLVSRWGOFO08 of Havells or equivalent of make Legrand/ABB complete with one MCCB 4 pole 415 Volts 250 Amps rating with rupturing cap 36 KA of the same make as of distribution board & with MCBs of required size making connections with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. 37 S&F Vertical TPN Loadline distribution board iron clad, doube door with IP-43 1K-09 protection suitable for MCCB as incomer and MCB as ougoing 415 Volts 3 phase 50 C/s 8 way, complete with appropriate size copper bus bar and neutral link, confirming to Cat Pt No DHDLVSRWGOFO08 of Havells or equivalent of make Legrand/ABB complete with one MCCB 4 pole 415 Volts 63 Amps rating with rupturing cap 16 KA of the same make as of distribution board & with MCBs of required size making connections with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. 38 S&F Vertical TPN Loadline distribution board iron clad, doube door with IP-43 1K-09 protection suitable for MCCB as incomer and MCB as ougoing 415 Volts 3 phase 50 C/s 8 way, complete with appropriate size copper bus bar and neutral link, confirming to Cat Pt No DHDLVSRWGOFO08 of Havells or equivalent of make Legrand/ABB complete with one MCCB 4 pole 415 Volts 160 Amps rating with rupturing cap 16 KA of the same make as of distribution board & with MCBs of required size making connections with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. 39 S&F Vertical TPN Loadline distribution board iron clad, doube door with IP-43 1K-09 protection suitable for MCCB as incomer and MCB as ougoing 415 Volts 3 phase 50 C/s 8 way, complete with appropriate size copper bus bar and neutral link, confirming to Cat Pt No DHDLVSRWGOFO08 of Havells or equivalent of make Legrand/ABB complete with one MCCB 4 pole 415 Volts 100 Amps rating with rupturing cap 16 KA of the same make as of distribution board & with MCBs of required size making connections with thimbles & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge. 40 S & F, installation, commissioning and testing Junction boxes made of Lid PC and base is polystyrene Hensel reference : KG series suitable . Junction Boxes Size 217 x 253 x 115 mm in Grey RAL 7035 colour. Junction Box IP 65 Thermoplastic PS Polystyrene weatherproof Junction Box with multi level knockouts for cable glands in different sizes. The pre-moulded knockouts shall be available on top and bottom of the junction box to enable cable entries from both direction. The junction box shall have an optional cable entry at the bottom up Cable Size 25 Sq mm of the box via pre-moulded knockout to enable pole mounting option. Lid fasteners self closedwill be tool operated. it will be sealable with accessories. The junction box shall have elongated holes inside them for wall/pole mounting provision. The junction box with 4 Pole Terminal Strip and MCB SP 6 Amp 10 KA C Curve for LED light. In the event of formation of condensed water, the junction box shall have a minimum of two condensation knock-outs inside to ensure optimum safe performance. 41 The junction box shall fulfill the following standardsWeatherproof : Rainwater proof, temperature resistant.IEC 60670-22 : Particular requirements for connecting boxes and enclosures.IEC 60695 – 2 – 11 : Flame – retardant & Self-extinguishing. Glow Wire tested at minimum 750 deg C.IEC 60529 : IP 65 degree of protection.UV Resistant in accordance with IEC 61 439-1, Clause no 8.4.4The Junction Box with Suitable Glands 3 Nos with each andchromium plated clamps, nut bolts complete all as per manufacturer’s instructions. 42 Supply, installation, testing and commissioning LT panel of suitable size as per IE rule and latest IS, factory made dust and vermin proof outdoor type made out of 3.15 mm thick CRCA sheet including seperate compartment for each MCCB & for cable and busbar, mounted on frame of MS angle iron 40mmx40mmx6 mm with front and back openable door with lock & Key including necessary grouting and double coat powder coated of grey colour painting complete with following accessories.The degree of protection of panel shall be IP-54 including foundation all as specified and directed.:- (Main LT Panel )INCOMING:(a) Aluminium bus bar 3 phase 4 strip suitable for 600 Amps current carrying capacitycomplete with post insulators and heat shrinkable sleeves- 01 No.(b) MCB TPN, 415 V, 10 KA, with Thermal Magnetic Release of capacity 16 Amps - 01 No Incomer 43 OUTGOING:(c) MCB TPN, 415 V, 10 KA, with Thermal Magnetic Release of capacity 10 Amps - 02 Nos O/G(d) Indicator Lamp LED type (RYB) - 01 Set (e) Digital type Ammeter 3 Ph with in built selector switchsuitable up to 100 Amp including suitable rating CTs -01 Set(f) Digital type Voltmeter 3 Ph with in built selector switchsuitable up to 500 Volt- 01 Set(g) All accessories prewired with appropriate size copper strip or wire thimbles etc.(h) All as required including foundations as per Manufacturers recommendations as directed by Engr-in-Charge. 44 Supply & installation of silent CPCB4 approved 625 KVA TPDiesel Generating Set having diesel engine Liquid cooled, Electric start, four stroke, cold starting, TCI Aspirated, compression ignition, totally enclosed diesel engine with electronic governor , direct coupled ith 625 KVA Three Phase alternator at 1500 RPM, 0.8 lagging power factor, providing Three Phase 415Volts suitable for 50 Hz, H class insulated winding, Close-direct-coupled, Self-excited and self-regulated type, screen protected, mounted on rigid MS sheet channel base-frame. The alternator shall confirm to IS: 13364, IS: 4722, BS5000, IEC: 34 and suitable for tropical condition. having fitted inside Canopy, fabricated out of 1.6 mm CRCA Sheet, cubical type, totally enclosed, Powder Coated, Control Panel and all accessories in- housed in a acoustic enclosure – sound proof canopy. 45 (A) Diesel Engine: - Adquate capacity of Diesel engine as accepted by the accepting officer based on manufacturers technical details water cooled to drive independently above alternator and after considering derating as per site conditons after generating and reducing power consumed by accessories directly coupled through flexiable coupling multi cylinder multi stroke direct injection,cold starting 1500 RPM, as per relevant ISI/BS - 5514 with an overload capacity of 10% for half an hour in 12 hours continuous running complete with standard accessories all as specified and required for safe handling and operation salient features of accessories shall be as under:- 46 i) Fly wheel with housingii) Cooling system :- Moulded radiator with fan & belts.iii) Cooling Water pump : - Centrifugal type belt driven.iv) Exhaust System :- Exhaust System complete with exhaust piping of 150mm dia with MS pipe light grade upto & outside and 1meter away from the enclosure, covered with asbestos rope and aluminium foil of complete with in the enclosure for safe exhaust without transforming vibration to the wall of the enclousre. Exhaust gas turbo charger type, Exhaust manifold, Silecer : Residual type, Bellows 47 iv) Fule System :- Fuel injection system with fuel injectors, fuel injection solenoid switch controlled by electronic governer for 1% speed /frequecy regulation. Fuel filters, Fuel hosesv) Lub oil System :-Lubricating oil filter, Lubricating oil pumpvi) Air Intake System :- Air intake Manifold, Air cleanler dry type, vii) Governer :- Electronic Governer, viii) Starting System :- Electric Self starter with maintenace free battary including battary charging alternator. 48 (B) Batteries :- 24 VDC system 2x180 AH Batteries of maintenece free of capacity as recommended by the manufacturer complete with copper conductor multistrnded leads of suitable length from self starter to the battary terminals complete with initial charge and initial fill of electrolyte all as specified of Make as per OEM.D) Starter gear ring, Start and stop push button, Ignition key / Switch, Handling and operation : Salient features of accessories shall be as under, Radiator with blower fan, Corrosion inhibitor coolant, Paper element filters for fuel, lub oil and by pass. Electronic governer controlled direct fuel injection system, Fly wheel housing and fly wheel. 49 (C) Generator Monitoring Control Panel : - Comprising of all standard items as mentioned under this schedule or as per standardpractice iginiton key switch and start / stop arrangement, indications for Engine parametes, hour run meter, RPM meter, Engine oil pressure indicator, water/coolent temparature indicator, Battary volt display including suitable size MCCBs and multifuction meter.xi) Safety Controls : - Engine low lube oil pressure high water temparature and over speeding of engine.xii) Coupling arrngement : - Flexiable coupling, fly wheel to suit flexiable coupling. 50 xiii) Accessories :- AVM Pads built or separtely mounted to manufactrer base frames.xiv) Base Frame with anti vibration pads on base frame: - Made out of ISMC 250 of sturdy design made of MS channel with necessary reinforcement and predetermined holes.xv) MS pipe line to and from the fuel tank to the DG Set.(D) Alternator :-Standard design alternator rated at 625 KVA,net output at site after considering derating as per site conditions at 0.8 (lag) power factor AC,3 - phase 4 - wire 415 volts 50 Hz, 1500 RPM, self exicited self regulated screen protected drip proof IP 23 enclosure brushless design with widing in pole faces, insulating class H and voltage regulation of+ 1% at rated voltage from no load to full load. The alternator shall be confirming to BS 2613/5000 and shall be inposition to generate supply with frequecy regulation with in + 1% tolerace. The alternator will be suitable for tropical climate and shall generally confirm to BS - 2613/5000/ IS - 4722. 51 i) Insualation class - H, ii) Temparature rise Class - H, iii) Excitation : Self Excited, iv) Regulation performance: The voltage is kept constant with + 1%, manual voltage adjustment within + 5% . v) Frequency regulation + 1%F). Civil Works :- All civil works including PCC plat form as per manufactures design also 30 cm above the ground. The depth of the foundation and PCC as recommended by the manufacturer. G) Rubber Mattingof LV grade 19mm thick of suitable size chequred type ISI marked to be laid in front of control panel should be provided.Note:- The contractor shall arrange for artificial load for testing for final testing of DG Set at site and the cost is deemed to be including in above offer. 52 (E) Accoustic Enclosure:- Manufactured by OEM suitable for 625 KVA DG Set. (i) NAL approved as per CPCB(ii) It Should be as per latest rules and regulations of Ministry of Environment and Forest and Pollution control board.(iii) The generating setbattaries and control panel should be inside the enclosure.(iv) Fuel tank should be out side the enclosure in the sub station building.v) The DG Set should be provided with external Emergency stop push button.vi) The battaries should be placed inside the enclosure beside the DG Set on a suitable inlsulatedplatform.viii) The enclosure should be suitably illuminated by suitable capacity of LEDfittings.xi) The noise level should be 75 db at 1m under free field conditions. 53 xii) The accoustic enclosure parts shall be of powder coated after pre treat ment process. The powder coating shade should be Genset Green. The base frame should be painted with epoxy based black shade.xiii) Fuel tank as per manufacturer recommendation with inlet and outler connections and fuel level indicator.NOTE : - (i) TheGenerator set prime mover will produce at least 734 BHP on 625 KVA.(ii) Rate quoted shall be deemed to be inclusive of cable and terminations form Generator to the AMF Panel, with necessary holes to wall including making good to distrbed surfaces so as to match with the existing finishes all as specified and directed.(iii) The quoted rate shall be deemed to be inclusive of first filling of lubricant oil. (iv) The quoted rate shall be deemed to be inclusive of 24 hours test run at site including of half an hour on 10% overhead in presence of representative detailed by accepting Officer; including FOL, all arrangements are to be made by the contractor for tests. 54 Supply and fix off LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 1000 Amps complete all as specified and directed. 55 Supply and fixing LED blub full dum 7 watt with rechargeble type, retrofit all as specified and directed by Engr-in-charge 56 S&F Double door three phase prewired distribution board vertical DB TPN 4 way with acrylic door made out of CRCA sheets 1.6 mm thick,phosphatised powder coated with copper Bus Bar 200 Amps, 415 V,IP 43/IK09, Earth Stud, Din Rail, Polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box ,ground terminal blocks ,duly prewired with thimbled flame retardant copper conductors and poly layer for protection in and includingMCCB4 pole 100 Amp rating repturing capacity 16 KA (Note:- Single Phase MCBs are to be measured and paid for seperately) 57 S&F Double door three phase prewired distribution board vertical DB TPN 4 way with acrylic door made out of CRCA sheets 1.6 mm thick,phosphatised powder coated with copper Bus Bar 200 Amps, 415 V,IP 43/IK09, Earth Stud, Din Rail, Polymide terminal blocks for incoming and outgoing circuits, inbuilt loose wire box ,ground terminal blocks ,duly prewired with thimbled flame retardant copper conductors and poly layer for protection in and includingMCCB4 pole 200 Amp rating repturing capacity 16 KA (Note:- Single Phase MCBs are to be measured and paid for seperately) 58 S&F LED building security light, pressure die cast aluminum housing, 20/25 watts capacity, toughned glass, 240V, IP 66 class, impact resistence IK07, with suitable in-built electronic driver complete incld. fixed on a bracket made out of 1.5 mtr long Med grade GI pipe 40 mm dia bend to shape as directed fitted on wall at a height not less than 5 mtr from groundwith MS clamp, nuts and bolts and washers as required at site and incld. connecting luminarie to the nearest ceiling rose/junction box with 1.5 sqmm PVC insulated 3 core wire complete all as directed and specified by Engr-in-Charge. NOTE - Cost of all minor spares and jobs required for fixing of light fixture on wall and for electrical connections are deemed to be included in the quoted rate. 59 Supply and Fixing of 40W LED High Bay light with Surface mounted device(SMD) with multiple LED with Borosilicate glass lens and acrylic, with aluminum reflector,operating Voltage between 140-270Vac, Power Factor more than 0.95%, intergal driver with 3KV surge protection differential mode/coman mode ,LED CCT 5665±355K as per ANSI BIN, Over load protection,No load Protection, Driver should be concealed under IP66 and BIS Marking (R no. for Driver), Driver Certiifcation IEC64347-2-13 IS(15885), System Lumen >4000, CRI>70, Over all electrical efficency more than 90%,connecting with PVC copper cable of size 3x1 sqmm at least 2 Year on site warranty wihout any condition including taking down of old light fitting safely and removing from site complete all as specified and directed. 60 SCH A PART - XIV(HOT WATER SUPPLY)Note: This schedule is not pre-priced by MES and the rate indicated as Rs 0.00 under Col 5 signifies this fact only 61 Supply and fixing of 5 star rated Water Heaters Storage type (Geysers) of Capacity 25 ltrs including grouting the nuts, bolts, washers of adequate size and all other accessories required at site for the effective functioning of the water heater complete all as specified and directed.Note :(i) Cost of Stop cocks deemed to be included in the quoted rate no extra payment shall be made.(ii) PVC connections, Bib cock and GI pipe shall be measured and paid seperately. 62 S&F BIB TAPS, chromim plated cast copper alloy with capstain head, screwed for 20mm bore dia iron pipes or for brass ferruble and fixed complete all specified and directed. 63 S&F PVC connection 15mm dia with PTMT nuts of length 450mm complete all as specified and directed. 64 SCH A PART - XV(CENTRAL HEATING SYSTEM)Note: This schedule is not pre-priced by MES and the rate indicated as Rs 0.00 under Col 5 signifies this fact only 65 Electric Hot Water Generator : Supply, installation, testing and commissioning ofpackage type electric Hot Water generator constructed out of MS sheet having top open-able cover for easy access and removal of heaters. The HWG shall be suitable for indoor mounting. The generator shall be provided with 50mm thick fibre glass insulation 32 kg density finished with 0.8mm / 22G aluminium cladding sheet. The generator shall have electrical capacity of 150 kW. The heater shall be electrical resistance type, copper tube with chromium plating. The generator shall be complete with float valve, pressure gauge with ball valve, master and bank thermostats, etc. The generator shall be suitable for 3 phase, 415+ 10% Volts, 50 Hz. AC supply. The generator shall complete with self-contained incoming isolation, ammeter, voltmeter, contactors for heater banks in three steps complete with manual/auto rotary switches. 66 (a) All neccassary accessories required for the proper fucntioning of Hot Water Genearator are included in price.(b) The prices should include lifting, shifting and positioning of units at Site.(c) Hot Water Genearator installation to done as per Manufacturer recommendation with all installation requirements i.e Foundation, Vibration Isolator,Insulationetc as recommended by Manufacturer for the Ambient Temperature of Site. ODU installation is included in ODU price which includes the Civil Struture, Mechanical Structureetc as recommended byManufacturer. (d) The Contractor/OEM will shall submit the Hot Water Generator capacity/Burner Capacity as per ISO or equivalent standard.(e) OEM should submit the Installation and Maintenance Schedule/ Manual for the Boiler. 67 GLYCOL CIRCULATION CENTRIFUGAL PUMPS: Supply, Installation, Testing & Commissioning of PN16 ratedAxial Split Coupled Vertical Inline water pump set with CI casing, Bronze Impeller, SS Shaft and externally flushed outside type balanced mechanical seal and non overloading motor, as per specifications and drawings. with Suitable HP, TEFC squirrel cage induction motor with EFF1 type class F insulation, Motor shall be rating of IP 55, operating on 415 ±10% volts, 3 phase, 50Hz AC Supply. The external flush line must be used for the purpose of heat dissipation from the mechanical seal.Pumps with performance characteristics as given below: The internal components of pumps including mechanical seal shall be suitable to sustain a fluid temperature of -25 Degree Celcius to 120 Degree Celcius. Vendor shall be provide antivibration arrangement for pumps . 68 The scope also shall include following below mentioned:(i) Electrical by pass starter for pump setas recommended by OEM.(ii) 25 mm thick polyviny nitrile rubber insulation duly cladded between aluminium sheets of 0.5mm thickness and properly clamped to pump.(iii) 3 Nos.- 150 mm dia type pressure gauges(iv) Mounting frame with antivibration pads (In case pumps are inline, anti vibration system shall be as per Manufacturers recommendation)(v) RCC/Cement concrete foundation for the pump unit. (In case pumps are inline, foundation shall be as per Manufacturers recommendation). (vi) Pump capacity are as under:(vii) Capacityand pump headnot less than flow 350 USGPM , Head 35 mtr each including the triple duct valve and End Suction guide. Note:- In 02 Nos working and 01 No standby configuration. 69 EXPANSION TANK and Pressurisation Unit: Supply, Installation, Testing and commissioning of INSULATED PRESSURISED CLOSED WATER EXPANSION TANK suitable for total volume ofGlycol - Water Solution, circuit along with necessary accessories such as along with necessary accessories such as 2 Nos pumps (1working +1standby) with Pressure Transmitter andinterconnecting Pipe & Isolating Valve complete with piping connections, safety relief valve, drain valve, pressure gauge, automatic air purging arrangement, etc.with Pressure Transmitter andinterconnecting Pipe & Isolating Valve complete with piping connections, safety relief valve, drain valve, pressure gauge, automatic air purging arrangement, etc. The tank shall be pre-charged. Expansion tank Shall be with replaceable heavy duty butyl rubber bladder. 70 The tankconnections should be as per OEM recommendationsand 20 mm drain and charging valve connection to facilitate the on site charging of nitrogen in the tank.The tank shall be fitted with lifting rings and a floor mounting skirt for vertical installation. The tank must be constructed in accordance with IS-STANDARD 2825-1969 (withlates Revision)and Rated at PN 16 and ASME Stamped. The complete system shall be sourced from single manufacturer and supplied and installed with all accessories and safety fixtures required for proper functioning of the complete hydronic system. 71 The tank shall be duly painted in approved colour shall be complete with pressure switches and power distribution and control panelIP55 Control Panel, Pressure Transmitter, interconnecting piping & wiring. (Tank capacity 1000 Ltrs). Hot Glycol - Water closed vessel pressurized expansion tank as described above shall be duly Insulated with 50 mm thick PUF/Nitrile Rubber insulating material or Equivalent U valueInsulating Material and cladded with aluminium Sheet (20G). 72 (a)Expansion Tank of 1000 Lts capacity for bldg 73 (b)PRESSURIZATION UNIT: for Pump Set -03 Nos (Ref. Point 4) with Control Panel and accessories for bldg. 74 Make Up TANK: Supply, installation, testing and commissioning of factory made Make up Water Tank, Rectangular/Circular shape, of 4 mm thick MS sheet (IS 2062), of capacity of 990 litres for Pocket-1complete with inlet, outlet, overflow, drain pipe of MS and vent with flame arrestor. Tank will be provided with supports made out of minimum 50mm angle iron duly painted, to keep tank base at minimum (1000mm) above FFL. Service platform shall be provided as per recommendations of OEM. The tank shall be provided with remote indication of levels provided level switches for on-off operation of tranfer pump. Extra high level and extra low level alarm shall be provided. Tank and structure shall be painted with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.Make up Water tank as describedabove should beduly Insulated with 50 mm thick PUF/Nitrile Rubber insulating material and cladded with aluminium Sheet (20G). 75 Supply, Installation, Testing and Commissioning ofCeiling Suspended Fan Coil Unit having casing with bottom return Air Plenum complete including Direct driven fan (three speed) motor, operated on 230 volts, single phase, 50Hz, AC supply. Unit to be provided with inbulit 2way wall withcordless remote. The Ball Valve with Strainer/ Shut off Value with Strainer at inlet and outlet of FCU including copper connection pipe for inlet and outlet should be provided. The Unit Capacityshould becalculated as per BIS/ Eurovent Standard/AHRI Certification method.The below desired capacity should be calculated at Altitude of 3600 mts above sea level. Capacity calculation sheet to be provided to Engineer in Charge. The below mentioned capacity is at INLET TEMP: 65 Degree Celcius , OUTLET TEMP: 55 Degree Celcius and Below Mention External Static Pressure (ESP). 76 2.5 kW,ESP: 50 Pa (Reference Model No.:FWW200VC / Equivalent)(CHS Plant Room - Toilet ) 77 5 kW,ESP: 50 Pa (Reference Model No.:FWW500VC/Equivalent) (Wkshp Toilet Area - 4 Qty, CHS Plant Room - Toilet- 1 Qty) 78 10kW,ESP: 50 Pa ( Reference Model No.:FWW1000VC/Equivalent)(Staff Room: 2 Qty, SPL Shop, Tech TRG, Tech LIB, Inspection OFF, Office for Wksh- 1 Qty 79 12 kW,ESP: 100 Pa( Reference Model No.:FUW015A/Equivalent)(Electricain - 1 Qty) 80 18kW,ESP: 100 Pa ( Reference Model No.:FUW020A/Equivalent)(Office for QC n Fuel Injection - 1 Qty) 81 24 kW,ESP: 100 Pa( Reference Model No.:FUW030A/Equivalent)(Mech Section- 1 Qty) 82 30kW,ESP: 100 Pa (Reference Model No.:FUW035A/Equivalent)(Service Bay - 2 Qty Each Service Bay) 83 M & L for Pre - insulated MS pipe,Class C havingminimum thicknes of PUF insulation as mentioned below and of density 36 Kg/Cum and 26 gauge GI/AL cladding complete suitable for above ground as per sizes shown.The pipes should be insulated with closed cell puf of density 36±2 Kg/Cum of below mentioned thickness. The Pipe should be workable in the temp. range of-50 Degree Celciusto120 Degreec Celcius. Note:-The Pipes size 150mm & below shall be M.S. ‘C’ class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. And from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 84 Inside Building 85 100 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 86 80 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 87 65 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 88 50 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 89 40 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 90 20 mm with 36 mm PUF thicknes and 26 Gauge Al Cladding. 91 Buried under ground/Exposed to Ambient: 92 100 mm with 50 mm PUF thicknes and HDPE Cladding, 26 Gauge Al Cladding. 93 80 mm with 50 mm PUF thicknes and HDPE Cladding, 26 Gauge Al Cladding. 94 Supply,Installation, Testing amd commissioning of PVC (minimum 15kg/sqcm pressure rated) drain water piping complete with fittings(elbows,tees, reducers,sockets,u trap etc.) supports, jointinginsulated with XLPE class O tubular insulation and any other item required to make the system compelete. Nominal diameters of pipein mms as inducated below: 95 25 mm dia pipe, Insulation thickness - 19 mm 96 32 mm dia pipe, Insulation thickness - 19 mm 97 40 mm dia pipe, Insulation thickness - 19 mm 98 CABLE TRAYS 99 Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling/Ground/wall with M.S. suspenders including bolts & nuts, painting suspenders etc. as required 100 150 mm width X 50 mm depth X 1.6 mm thickness 101 VALVES : 102 Supplying, fixing, testing and commissioning of following diameter valves(PN-16 Rating) (Complete with Flanges integral or welded, fittings, Nuts, Bolts & Gaskets (PN-16 Rating), strainers (Complete with flanges integral or welded, fittings, Nuts, Bolts & Gaskets (PN-16 Rating), gauges etc for condenser water circulation as per specifications. Insulation thickness ofvalves should be equal to the Insulation of PUF and GI Cladding of Pipe Section as specified.Butterfly Valve ( Insulated Valves) with CI body SS disc nitrile sheet & O ring, Complete with fittings, Nuts, Bolts & Gaskets. 103 100 mm dia Butterfly Valve 104 65 mm dia Butterfly Valve 105 Y - STRAINER (Insulated Valves) of Ductile CI Body flanged ends with stainless steel strainer forhot water circulation including Insulation thickness ofvalves should be equal to the Insulation of PUF and GI Cladding of Pipe Section as specified. 106 65 mm dia Y STRAINER 107 NON - RETURN VALVE (Insulated Valves) with duel plate of CI body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating forhot water circulation includingInsulation thickness ofvalves should be equal to the Insulation of PUF and GI Cladding of Pipe Section as sepcified. 108 65 mm dia NRV 109 Automatic Air Purge Valves forhot water circulation headeras specified and required by Engineer In Charge. 110 Automtic Air Purge Valve 20 mmdia 111 Air Separator (PN16) 112 65 mm 113 SITC of water pressure gauge (100 mm dia) bourdon type with brass ball valve of 3/8 dia and SS tubing, socket.Range (0-50) / (0-100) as required by Engineer In Charge. 114 SITC of Mercury in glass industrial thermometer in SS-304 casing with 0.5 C least count, range 0-50 C. Brass oil filled thermowell of 1/2 size as required by Engineer In Charge. 115 Supply, installation, commissioning and testing of factory made, CPRI approved LTCHS Plant, indoor type made out of CRCA sheet 2 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase4 wire, 415 Volts, 50 Hz, AC supply system, floor mounted and grounting the legs of panel in PCC foundation 1:4:8 complete as all directed suitable for and including the following :- As per IE rule and latest is, necessary colour coding for R, Y, B and N shall be made with different colour as per IE rule. 116 INCOMERS(a) Bus Bar TPN Copper extensible type main bus bars of minimum of1200 A capacity (As per capacity of corresponding incoming / Bus couplers) , and auxilliary bus bars ofsuitable capacity with heat shrunk coloured sleeves and i/c SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of50kA .(b)ACB 800 Amps, 415 Volt, 50 KA, 4 Pole, thermal magnetic release - 01 No for incoming (Extended Rotary Operating Handle, Phase Spreader links and Phase barriers) Make: Legrand/Schenider/Simens 117 OUTGOINGS(c) 4 Nos- 400A 10 KA TPNMCCBwith Microprocessor release (3# Hot Water Generator) (d) MCB 5/6 Amp, 10KA, TPN - 02NosPressurization PUMPs (e) MCB 50 Amp, 10KA, TPN - 03 Nos for Pumps(f) MCB 5/6 Amp, 10KA, SPN,- 07No for Bldg load/FCU. Makes of MCBs: Legrand/Schenider/Simens(g) LED Phase indication lamps (01 Set) with 2Amp back up MCB,Breaker ON/OFF indicating light with 2A MCB, test terminal block set, circuits as per standard practice, auxiliary contacts for positive interlocking of the breakers as required. - 2 Set 118 (h) Digital Ammeter with in built ASS,metering C.T.sCAST RESIN type, 15VA, and accuracy class-1of 800/5A for measuring current in each phase - 01 Set.(j) All accessories prewired with appropriate size copper strip or wire and thimbles etc. all as required including foundations as per Manufacturers recommendations all as directed by Engnr-in-Charge.Note : Contractor will submit the drawing of panel to GE before execution for approval. 119 Supply & Laying/ fixing of following size XLPE insulated and PVC sheathed Copper conductor armoured cable/unarmoured as required of 1.1 KV grade complete as required. (ISI Marked) (in ground/in pipe/in duct/on surface/on cable tray) 120 3.5 Core x 250 sq.mm. (Electric Hot Water Generator) 121 4 Core x 10 sq.mm. (Pump) 122 4 Core x 6 sq.mm (Pressurization Unit) 123 2 Single corex 2.5 sq.mm. (FCU) 124 4 Core x 4 sq.mm (Boiler Pump) 125 Earthing complete with GIearth plate electrode of size 60cm X 60cm X 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to and including GI strip of size 32x6 mm up to 7.5 mtr by means of bolts, nuts, check nuts and washers made of brass and protected by light grade 40mm dia upto 7.5 mtr long GI pipe connected to main controlboard and GI pipe light grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover 50mm thick and PCC chamber pit with PCC 1:2:4 type C2 (including excavation and earth work disposal of surplus soil to a distance not exceeding 50 metre) and testing making test point and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 complete all as specified & directed by Engr-in-charge. 126 Supply and fixing rubber matting conforming to IS-15652-2006 complete as required. of size2m * 1m * 25 mm complete all as specified & directed by Engr-in-charge. 127 Supplying of Ethylene glycol concentrate along with the necessary additives and inhibitor in cognition in sealed barrels for CHS complete all as directed.NOTE;- (i) The glycol concentrate shall be mixed with potable water supplied by contractor and filled in central heating system pipe line after proper leak test of entire circuit. The glycol water mixture ratio shall be 55:45 and freezing temperature shall be - 45 Degree Celcius (ii) First charge of glycol is included in the quoted rate. First Charge Include Charge in CHS pipe lineStorage Tank. 128 GENERAL NOTES:- 129 1. The rate for each item of work included in the Schedule of Quantities shall, unless expressly stated otherwise, include cost of :(a) All materials, fixing materials, accessories, appliances tools, plants, equipment, transport, labour and incidentals required in preparation for and in the full and entire execution, testing, balancing, commissioning and completion of work called for in the item and as per Specifications and Drawings.(b) Wastage on materials and labour.(c) Loading, transporting, unloading, handling/double handling, hoisting to all levels, setting, fitting and fixing in position, protecting, disposal of debris and all other labour necessary in and for the full and entire execution and for the job in accordance with the contract documents, good practice and recognize principles. 130 (d) Liabilities, obligations and risks arising out of Conditions of Contract.(e) The unit rate for all equipment or materials in Indian Rupees shall include cost of equipment and materials including all taxes and duties and also including forwarding, freight, insurance and transport into Contractor’s store at site, storage, installation, testing, balancing, commissioning and other works required.2. The contractor shall perform Nitrogen test and vacuum test on refrigerant piping. Start and stop timing & pressure maintained shall be checked and the readings recorded shall be counter signed by consultant / client’s representative. 131 3. Cable glands shall be compression type, heavy-duty chromium plated.4. All cable termination to have lugs/ thimbles.5. INSTRUCTION / MAINTENANCE MANUAL 132 The Contractor shall prepare and produce instruction, operation and maintenance manuals in English for the use, operation and the maintenance of the supplied equipment and installations and submit to the Client / Consultant in (3) copies at the time of handing over. The manual shallgenerally consist of the following:(i) Description of the project.(ii) Operatinginstructions.(iii)Maintenance instructions including procedures for preventive maintenance.(iv) Manufacturers catalogues.(v) Trouble shooting charts.(vi) Schematic & control wiring diagrams. 133 (vii) Commissioning Certificate.(viii) Also for BMS System, Training,Opeartion, Installation manual and Trouble shooting manual and Training should be imparted to the field person.(ix) Allneccassary license should be provided for the BMS free of cost.6. For Make List If any make stated below does not comply with the technical specifications and or IS Standards then such a make shall not be used in the work. 7.MAINTENANCE OF PLANT AND TRAINING OF PERSONNELThe Cont ractor shall arrange to provide, at no extra cost, necessary personnel and material to carry out all routine maintenance of the CHS equipment as required regularly.