BRR : 9528620 Tender For Provision Of Cgsd (Kochi) At Willingdon Island, Kochi; 1 SCHEDULE A Part - I (BUILDING & STRUCTURE WORKS)Details of prepriced schedule is given in tender documents. 2 SCHEDULE A PART-II ( SITE CLEARENCE/DEVELOPMENT & EARTH WORKS) Details of prepriced Schedule is given in tender documents. 3 SCHEDULE A PART-III (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents. 4 SCHEDULE A PART-IV (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents. 5 SCHEDULE A PART-V (FIRE FIGHTING)Details of prepriced Schedule is given in tender documents. 6 SCHEDULE A PART-VI (ROAD/PATH/ HARD STANDING/CULVERT)Details of prepriced Schedule is given in tender documents. 7 SCHEDULE A PART-VII (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents. 8 SCHEDULE A PART-VIII (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents. 9 SCHEDULE A PART-IX (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents. 10 SCHEDULE A PART-X (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents. 11 SCHEDULE A PART-XI (COMPOUND WALL) Details of prepriced Schedule is given in tender documents. 12 SCHEDULE A PART-XII (ORGANIC WASTE CONVERTER AND SMART ENERGY METER) Details of prepriced Schedule is given in tender documents. 13 SCHEDULE A PART -XIII (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the rate shall be quoted by the bidder. 14 INTERNAL WATER SUPPLY S & F for 15 mm dia bore CP two way bib cock with CP wall flange (Make : Jaquar Model No. OPP15041PM / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 15 S & F for 15 mm dia bore CP bib cock with CP wall flange (Make : Jaquar Model No. OPP15037PM / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch, screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 16 S & F for 20 mm bore concealed Stop cock reqular brass body with spindle extnwith Exposed Part Kit of Concealed Stop Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange (Compatible with ALD-083CQT & ALD-089CQT)(Make : Jaquar Model No. ALD 089 CQT/ Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch , screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 17 S & F for 25 mm dia bore concealed Stop cock reqular brass body with spindle extn with Flush Cock & Wall Flange 25mm Ceramic Disc Cartridge) with Plain Knob (Make : Jaquar Model No. ALD 081/ Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch, screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 18 S & F 20mm bore CP angular stop cock with CP wall flange (Make : Jaquar Model No. CQT 23053 / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down, high pressure with crutch, screwed both ends for iron pipe or for union and fixed 19 S & F for 100 mm overhead shower rose round shape single flow (ABS Body chrome plated with gray face plate (Make : Jaquar Model No. 1989 with SHA 479L300S / Eqvlt in Kohler/ ESS ESS) with Shower Arm ø20mm & 300mm Long Round Shape with 90˚ Bend for Wall Mounted Showers with Stainless Steel connected to pipe complete all as specified and directed by Engr-in-charge. 20 COOLING APPLIANCESDesign, Supply, Installation, Testing and Commissioning of Invertor Type Floor Mounted Packaged AC Units including indoor and outdoor unit complete of specified capacities, combination of energy efficient Inverter compressor plus fixed compressors, nominal capacity condensing unit with all standard fittings, safety devices, like HP/LP cutout, single phase preventor, overload relays, R-410A Gas, vibration isolation pads etc. Suitable to work till 50 Deg ambient, Blue Fin Condensor and Corrosion Resistant Body, Wide Voltage Range 360V - 440V, The quoted rate shall include Group controller also asrequired for controlling AC from a single point and timer option for load sharing of AC units complete all as specified and as directed by Engineer - in - charge, of following capacities.Note: Design report shall be submitted before execution of work at site by the contractor to GE for his scruitiny/comments and further submitted to AO for his approval.Make: Blue Star/Daikin/Haeir/Godrej/Voltas/Equivalent. 21 a) 22 TR Inverter Package AC Units 22 b) 16.5 TR Inverter Package AC Unit 23 BLANK 24 BLANK 25 BLANK 26 Supply, Installation and Testing of Refrigerant pipingwith necessary clamping (suction & Discharge) Hard/Soft drawn Copper tube of suitable sizes, with copper elbows, tees, Tubular Nitrile Insulations etc as required complete all as specified and as directed by Engineer - in - charge. 27 S & F Control Cabling B/W Indoor & Outdoor units 28 M & L Refrigerant Gas - R410A 29 Supply, Installation and Testing of Hard PVC drain piping. Drain piping with Tubular Nitrile Rubber Insulation: complete in all respects, well clamped till drain Points complete all as specified and as directed by Engineer - in - charge. For All Units 30 DUCTINGSupply, fabrication, installation, testing of GI rectangular ducts, complete with all fittings such as tee, bends, special off shoots, inspection doors, transformation pieces etc. as required as per IS 655 including suspension and supporting arrangement for plenum, duct etc. required complete all as specified and as directed by Engineer - in - charge. 31 a) Using 0.63 mm (24 Gauge) GI sheet 32 b) Using 0.80 mm (22 Gauge) GI sheet 33 c) Using 1.00 mm (20 Gauge) GI sheet 34 DUCT INSULATION & LININGSupply and Installation of Acoustic Insulation of ducts using 9MM Open Cell Nitrile Rubber, well adhesived, 150 - 180 Kg/cm2 complete all as specified and as directed by Engineer - in - charge. 35 Supply, installation & testing of Thermal Insulation of ducts using 9MM Closed Cell Nitrile Rubber, well adhesived, 40-60 Kg/cm2 complete all as specified and as directed by Engineer - in - charge. 36 S & F Canvas Connection 37 AIR DISTRIBUTION PRODUCTSSupply and Fixing of Powder Coated Aluminium Grills/ Diffusers (Supply/ Return) complete all as specified and as directed by Engineer - in - charge. 38 S & F Collar Dampers 39 Supply and Installation of Fire Dampers complete all as specified and as directed by Engineer - in - charge. 40 Supply, Installation, Testing and Commissioning of Heater Bank Plus Humidistat Arrangement complete all as specified and as directed by Engineer - in - charge. 41 Supply and fixing, testing and commissioning water coolerhaving stainless steel body with inbuild purifier HIMA 7 NHC, dispencing capacity 125 ltr/hr and storage tank capacity 40 ltr normal and 40 cold electric driven (single phase), 230 volt, AC power supply with all connecting accessories complete all as specified and directed. 42 Supply and fixrefrigerator, electric driven (single phase), 220 V,50 HZ, capacity 195 Litres, 3 Star rated direct cool inverter, single door all as specified and directed by the Engineer-in-Charge. 43 Supply and install, testing and commissioning of split type air conditioner 1.5 TR Capacity of invertertechnology 5 star rating with cordless remote control single phase 240 volts complete with all accessories such as indoor and outdoor units and refrigerent tubing of adequete length as required at site indoor mounting plate, duly powder coated fixing with anchor bolts at any height, drain pipe of suitable size brought to ground level from any height, initial filling of refrigerent gas including making round hole on existing wall for taking up refrigerent tubing, drain pipe, cables, etc and making good the disturbed surface by matching with existing adjoining surface complete all as specified and directed (Cooling appliances- qty 4, Air conditioning- qty 10) 44 Supply and fix Voltage stabilizer 3 KVA for automatic operation, single phase naturally air cooled indoor type, wall mounted & designed for input variation between 170 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% 45 Supply and fix Voltage stabilizer 4 KVA for automatic operation, single phase naturally air cooled indoor type, wall mounted & designed for input variation between 170 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% (Cooling appliances-qty4, Air conditioning- qty 10) 46 AIR CONDITIONINGSupply and install,Testing & commissioning of split type air conditioner 2 TR capacity of inverter technology 5 star ratingwith cordless remote control, single phase 240 volts complete with all accessories such asindoor and outdoor units and refrigerent tubing of adequete length as required at site, indoor mounting plate, duly powder coated fixing with anchor bolts at any height, drain pipe of suitable size brought to ground level from any height, initial filling of refrigerent gas including making round hole on existing wall for taking up refrigerent tubing, drain pipe, cables etc and making good the surace by matching with adjoining surface complete all as specified and directed. 47 Supply and fix Voltage stabilizer 5 KVA for automatic operation,single phase naturally air cooled indoor type, Wall mounted type & designed for input variation between 170 V to 280 V with output voltage stabilized at230 V with accuracy of ± 2.5% 48 INTERNAL ELECTRIFICATIONS & F LED Mirror light 1 x 5W LUMOS ECCO 1 feet Make: Luker or Equivalent 49 S & F modular MCB DBOx 3 Pin Socket with MCB SP 20 Amp, 240 V including plastic enclosure as per manufacturer instruction fixed on wall surface complete for Air conditioner all as specified and as directed. (Make:-Havells, Model-DHDMCSN0251016 or equivalent) 50 Supply and fix Air circulator of 600 mm sweep AC single Phase. 230V, 1440 RPM complete all as specified and as directed. (Make: Havells model, Turbo Force Wall or equivalent) 51 S & FVertical triple pole & neutral (VTPN), double door, 16-way metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for FPMCCB as incomer and TPN/SP MCBs as outgoing, reversible metal door, 200 A copper busbar for each phase, fully insulated & shrouded neutral bar, earth bar, wiriest & cable ties for cable management, profited masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and directed. 52 S & FVertical triple pole & neutral (VTPN), double door, 4-way metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for FPMCCB as incomer and TPN/SP MCBs as outgoing, reversible metal door, 200 A copper busbar for each phase, fully insulated & shrouded neutral bar, earth bar, wiriest & cable ties for cable management, profited masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and directed. 53 M & L for Flame ProofMCB Distribution board SPN 12 way, with case iron body, powder painted, with 100 Amps rated bus bar etc. including provision of one 32 Amps SPN MCB as incoming and 6 Amps SP MCB -10 Nos as outgoingcomplete all as specified and as directed. 54 M & L for Flame ProofMCB Distribution board SPN 8 way, with case iron body, powder painted, with 200 Amps rated bus bar etc. including provision of one 32 Amps SPN MCB as incoming and 6 Amps SP MCB- 6 Nos as outgoingcomplete all as specified and as directed. 55 Supply and fix Engage light with Green & Red LED complete all as specified and as directed 56 Supply and fix of CS mounted high intensity LED search light, long range, manually swivel in all direction, 250 W, minimum range 700 meters, Single, LED Efficiency> 140 lm/w, PF> 0.95, CCT 5500K - 6500K, Optical grade PMMA/PC lens/reflector efficiency>95%, multiple circuit to avoid complete run down, anti UV, narrow beam 5 degree, die cast LM6 body with air fins, powder coated, constant current, an average lux at 10 meter - 8000 lux with circle of approx 600 mm, working temp: -20 to +60 degree C, input Volt 100-300 VAC, 50 Hz, PF >0.95, IP-66, confirming to LM79/ LM80 and type tested as per IS: 10322/ IS: 13383, BIS approved and Govt lab tested for lux intensity. The search light is completed with manual revolving CS stand D20cm x H15cm (min.) with 3 nos. foundation holes for mounting of searchlight on watchtower structure, manual rotation of light on horizontally 360 degree with 45 degree tiltable with provision of both instant locking arrangement at desired position. Model No. CS-LRFLL-25PC25 of KALIN make or equivalent 57 Supply, install, testing and commisisong of outdoor floor/wall mounted thermoplastic polycarbonatefeeder pillar panel, Enystar EmptyEnclosures, IP-65, weatherproof, corrosion free, Halogen and Silicon Free, Frame retardant with Opaque Lid Size-[276 x 546 x 186]mm and Transparent Hinged Lid, completed all as specified and directed. 58 M & L for TV socket module metal flushed including flushed Box cover plate Box for 2 way module complete all as specified. 59 M & L for telephone jack with module metal flushed including flushed Box cover plate Box for 2 way module complete all as specified. 60 Supply and lay coaxial cable for TV Cabledrawn through conduit 61 S & F flame proof exhaust fan 300 mm sweep, single phase, 1440 RPM complete all as specified and as directed. 62 FIRE FIGHTINGSupply and fix Foot Valve conforming to IS 4038, 100 mmdia. 63 Supply and fix Foot Valve conforming to IS 4038, 150 mmdia. 64 Supply and fix Cast Iron Air Valves with single air Outlets, conforming to IS 14845 of size 100 mm dia bore and fixing up in Cast Iron Water supply mains of size 100 mm dia. 65 S & F sprinkler flexible drop pipe 1 mtr long. 66 S & F sprinkler rossette 25 mm dia. 67 Supply and installation, testing and commissioning of Analog Addressable type Active Loop Repeater (Loop power/external power) Fire terminal with inbuit turbo isolator, Backlit LCD Display 6x40 characters display, having Controls For Reset, Mute, Accept, Silence alarms and Self Test, with programmable free keys and Duly Approved byEN54/LPCB/VDS/FM Make: SIEMENS/NOTIFIER/BOSCH 68 M & L for Low smoke Zero helogen flame retardent fire alarm cable2 core, 1.5 mm² copper conductor confirming to BS7629-I, BS6387 & rated for 500 v grade having plaine sraded copper coductutor with priming insulation of glass mica fire resistance tape & secondery insulation of high performancesilicon rubber with electrostatic screen of aluminium fire barrier Type LT53 outer sheath confirming to BS 7655, red in colour drawn through & including concealed steel conduit including laying,fixing,connecting complete all as specified and directed. 69 Staircase signage down of make bajaj cat part no. 111499 model no. DSDWBB 3W double side display for staircase downwards (with 2 hours built in battery backup) complete all as specified and directed at site complete all as specified and directed. 70 S & F wall mounted LED emergency Exit signage luminaire Lit up using regular mains supply comes with a unique rechargeable Ni-Cd battery capable of emergency back up upto 05 hours(Cat No. 220211 Make Bajaj or equivalent to CG/Havells. 71 Supply, Installation, test and Commissioning CPRI APPROVED factoryfabricated, indoor type, LT panel board , made out of 2 mm thick CRCA Sheetsingle door withboth side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeddedwith 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete withinternal connection with suitable size of cable, cable lugs and cable glandsPCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation includingcomplete all as specified and comprising of the following:- Make of MCCB/MCB -MDS/LEGRAND/L&T/HEGGER (Main Fire Fighting Panel)INCOMING(i) MCCB 4 Pole 400 amp 50 Hz, 415 V with rupturing capacity 35 KA with microprocessor based release - 01 No.(ii) Voltmeter Digital type 0-500 Volts range flush type with selector switch- 01 No.(iii) Aluminium Bus bar TPN - 600 amps- 1setOUTGOING(i) MCCB 3 Pole 200 amp 50 Hz, 415 V with rupturing capacity 35 KA with microprocessor based release- 02 No.(iii) MCB TPN 32 Amp - 03 Nos.(iv) 80 HP S/D soft STARTER- 02 Nos.(v) DOL STARTER 7.5 HP- 02 Nos.(vi) Motor Protection Relay32-88 amps- 2 nos. (vii) Motor Protection Relay2- 5.5 amps- 2 nos. (viii) On/Off/Trip Indication Lamps, 220 V AC- 6 nos.(ix) Start/Stop Push Button, 4 Nos. (x) Phase indicating lamps RYB for incoming and each outgoing connection.(xi) Digital type Ammeter 0- 150 amps with selector switch and CT coils of suitable capacity for incoming and each outgoing connection- 1 no. 72 M & L for coating and wrapping of under ground steel pipe buried in soil shall have protection against corrosion as per IS-10221.The coating and wrapping shall be carried out in systamatic manner to get uniform thickness of coating as per IS specification 73 Supply, Installation, test and Commissioning CPRI APPROVED factoryfabricated, Indoor type, LT panel board, made out of 2 mm thick CRCA Sheetsingle door withboth side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeddedwith 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete withinternal connection with suitable size of cable, cable lugs and cable glandsPCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation includingcomplete all as specified and & directedby Engr-in-charge comprising of the following :– ( Booster terrace pump panel)INCOMING:-(a) INCOMING MCCB 40 A 25 KA, 4 POLE- 01 No.(b) Busbar TPN of size 100 apms - 1 setOUTGOINGS:-(a) MCB 3 POLE TPN 32 Amps,10 KA-2 Nos.(b)DOL Starter for 7.5 HP Pump set-1 Nos.(c) Ammeter Class-1, digital panel mounting type 96mmx96mm L & T cat no WDS301FCA00 including CT 50X5 Amps 3 nos & selector switch-4 nos(d) Voltmeter Class- 1, digital panel mounting type 96mmx96mm L&T CAT NO.WDS301FEV00 & selector switch - 1 no.(e) LED TYPE indicator lamp 1 set (set of three for R,Y,B)(f) Mini protecrionRelay 4-11 amp - 1 nos. 74 Fire Extinguisher mechanical Foam type trolly mouted of 9 Liters capacity. Ceasefire 9 litrs fire Extinguisher AFFF Foam type, External Cartridge type, Pressure Guage Gross weight 14.6 Kg, empty weight5.6 Kg, Can height 611 MM, Diameter 175 MM, Discharge time less than 60 Secs controllable discharge mechanism, Minimum 6 Mtrs, Applicable on Class A, B, can construction deep down & CO2 Mig welded Valve Construction: Forging & Machining, Internal coating of can: Epoxy powder coating, External coating of can: Epoxy poyster powder coating sheet metal thickness 2.0MM,1 year warranty. Make Cease Fire Or Equivalent. (pol store) 75 Supply, Installation,Testing & commissioning of Carbon Dioxide (Co2) type fire extinguisher of 4.5 Kg confirm to IS: 15683, with ISI marked/TAC approved fitted with required accessories including wall suspension brackets. 76 Supply, Installation,Testing & commissioning ofDRY CHEMICAL POWDER (ABC) stored pressure type fire extinguisher of 6 Kg confirm to IS: 15683, with ISI marked/TAC approved fitted with required accessories including wall suspension brackets. 77 Supply and fixing single unit flame type detectors (Triple IR infrared flame detectors) Addressable type Flame detectors with UV/IR detection capacity (add up cost of module to be a complete set, the type of module shall be relaying type module) complete all as specified and directed 78 Supply and fixing,Test and Drain valve 65/50mm, forged brass body, brass chrome plated ball, 304SS stem with Polycarbonate sight glass, indicator and handle made of steel complete all as specified and directed 79 SPECIAL EQUIPMENTS FOR STORESDesign, manufacture, Supply, installation, testing and commissioning of Automated Storage and Retrieval System with storage racks, pallets, stacking crane, computer hardware with compatible inventory software as a turnkey solution complete all as specified and directed. Automated Storage and Retrieval System shall consist of computer controlled & PLC stacker crane driven system for automatically placing & retrieving materials from defined storage locations. The crane shall be capable of lifiting, stacking and retriveing the pallet loads weight upto 1125 Kg (max) complete all as specified and directed by the Engineer-in-Charge. Technical data for design of heavy duty ASRS:-(a) Dimensions:-Height:10 Mtrs for racking system which shall be designed and constructed to store the required no. and size of pallets.(b)Storage capacity:-Pallet Size: 1300 (W) x 1200(D) x 1250 (H) in mmPallet Nos.: 480Pallet load capacity: 1125 KgTotal capacity: 540 Tons(c) Stacker Crane: Double mast automated stacker crane for handling Pallet, size 1300mm(W) x 1200mm (D) x 1250mm (H) and pay load (including Pallet self weight) of 1125 Kg max. The stacker crane shall be capable of picking up the pallet from in-feed conveyor or loading station and stacking it into empty slots of racking system. Similarly, it shall also be capable of retrieving the palltet from racking system and putting it on the same conveyor or unloading station. Stacker crane will be mounted on rails at the bottom to traverse the length of the storage system. Top rails mounted on the racking system shall also support it. PMDC motars should be used with required counter weight for better efficiency of verticle travel.General technical parameters of stacker crane:Technical parameters/Type- Double Mast(i) Operation mode (Networking)- On-line automatic / Single automatic (Ground/Boarding) /Manual operation (Boarding) / Maintenance (ii) Communication Means- Wireless 80 (iii) Power supply mode- 380 to 415 V, 50 Hz, three phase five wire (iv) Addressing mode- Horizontal and verticle operation: photo electrical sensor + bar code scanners(v) Positioning / Reduction accuracy (mm) level- lifting ± 3 - 5, Fork : ± 3(vi) Fork unit- 1 Double deep fork(vii) Load unit- MS Pallet (viii) Total Height- 10 Mtr(ix) The normal lifting speed (m/min) - 10 MPM(x) The normal running speed (m/min) - 65 MPM(xi) Rated load- 1125 Kg(xii) Receipt equipment fixed platform/conveyor/lifting /platform(electric/manual)- Conveyor(d) Pallets: to stack and retrieve the pallet weighing up to loaded pallet weight 1125 Kg at height up to the last loading level in the racking system. It should have retrieval mechanism to enable stacking & retrieval of pallet from either side of the rack and also to pick up the load directly from the loading station.Pallet Details:-(i) Dimensions - 1300mm(W) x 1200mm(D)(ii) Pallet height- 1250 mm(e) Racking system:- Two single aisle having two row racking system each with 05 verticle levels for storage of material. Racking for double deep type storage of 480 Pallet of size 1300mm(W) x 1200mm (D) x 1250mm (H). Loaded pallet weight: Pay load with pallet 1125 Kg max. System details:-Working aisle -01 Nos. (Double deep)Store rack -24 Nos./RowTotal rack in 1 aisle-24 (Left) + 24 (Right)= 48 Nos.No. of level- 5 Nos/RackTotal Pallet-48 x 5 x 2 = 480 Nos.Load capacity- 1125 Kg/LevelDouble mast stacker crane-01 No. 81 (f)Aisle Equipment:-This will consist of electrical as well mechanical aisle equipments and willl be designed as per the pallet requirement. The mechanical Aisle equipment of bottom rail shall consist of I Beam and will be provided with adjustable calmps for holding the rail in position to ensure proper alignment. Top rail shall be mounted on the racking. The electrical aisle equipment shall consist of power rail (fully enclosed bus bar having 7 pole system), which is mounted on the racking system below the first loading level.(g) Details of rack members:-The racking system shall consist of cold-rolled steel sections as per manufacturers design to accommodate and store pallets and connected systems.(h) Loading- unloading station/ Conveyor(i) Pallet Load 1125 Kg max.(ii) Bearing- SKF Equivalent make(iii) Motor- Seimens/Sew Euro Drive/Nord Sew/ Bonfiglioli or equivalent(iv) Gear Box- Bonfiglioli Make or equivalent(v) V.F.D.- Yashkawa make or equivalent(j) All steel surface shall be powder coated finish with 8 tank treatment process.(k) Maintenence: The annual maintenence of complete ASRS system during the defect liability period of two years shall be included in the rate quoted for the system and the AMC contract duly signed with the manufacturer of the ASR system shall be submitted at the time of handling over the system. The AMC shall include all spares and consumables etc required during the period of two years and nothing extra shall be paid on this accountNote- 1)Mechanical safety provision (i) End of aisle shock absorbers / bumpers for stacker crane.(ii) End of travel buffer for the lifting crane.(iii) Safety catches on lifting carriage.(iv) Anti-tilt mechanism for the stacker crane. An additional antifall device must be provided for the lifting carriage. In the event of electromagnetic break motor failure or malfunction, this device should automatically engage to safely hold the carriage and prevent any freefall, thereby avoid accidents due to emergency brake failure.(v) Continuous rail cleaning brush for floor rail.(vi) Adjustable rail clamp to ensure alignment. 82 (vii) Resilient rubber pads on adjustable clamps for vibration dampening.(viii) Profile check on lifting carriage to check all three dimensions (width, depth & height) of the pallet. Note - 2 Electrical safety provision (i) There shall be Emergency stop push button at all panels and stations.(ii) Optical light beam amd mechanical safety sensor to stop the operation in case of improper storage.(iii) Back up circuitry for proper system operation.(iv) An electromagnetic brake shall be used to avoid the slippage of the hoist.(v) Stopper shall be provided for the maintenance door.(vi) Load cells shall be provided for the over weight of tray.(vii) Automatic door shall be provided for operator safety while machine in operating condition.Note - 3 Physical safety provision (i) The ASR system shall comprise of safety fences having grid size of max. 40 x 40mm & wire dia should be of min. 3 mm. Height of the fencing should be minimum 2.0 meter.(ii) One No. of electromagnetic aisle access door shall be provided. It should cover the complete length of the system on one side.(iii) A manual locking system to restrict the movement of unauthorised personnel shall be provided.NOTE: 1) Design report shall be submitted before execution of Work at site by the contractor toGE for his scrutiny / comments and futher submitted to AO for obtaining approval. Item No. 13.070 below shall be compatible with this item/ system and both should be integrated. Changes in make of different components of ASR system and minor changes in different parameters are permitted with approval of Accepting Officer as per recommendation of ASR system manufacturerprovidedthe end objective of the system is complied.2) The ASR system is to be installed in Bulk store house complex. Necessary civil works for installation of the ASRS required in the building is included in the scope of this item. Neccessary arrangements for integration of system with flooring and overhead trussess of the building shall be done at appropriate stage and shall be included in the rates quoted3) The PLC program backup for the ASRS and Advanced Inventory Management System shall be provided in an editable format. The WMS program shall be provided along with its source code to enable the user to perform maintenance, modifications and future upgrades as part of the project acceptanceMake of ASR system:Armstrong Ltd/ Godrej Koerber/ Kardex India storage solutions Pvt Ltd/ Daifuku India Pvt Ltd/ Addverb technologies Ltd/ Craftsman Automation Ltd/ Tech-mark 83 Supply, installation, testing and commissioning of Advanced Inventory Management System with compatibile computer hardware and integrated inventory and weight management system with PLC based software complete all as specified and directed by the Engineer-in-Charge. Technical specification of the system(i) System Height(Min) : 6400 (±100) mm(ii) System Width(Min) : 3150 (±100) mm(iii) System Depth(Min) : 2300 (±100) mm(iv) System Base(Min) : 7.24 Sq.Mtr(v) Tray Int. Size(Min): 300 (H) x 2450(W) x 500 (D) in mm(vi) Tray dead weight(Min) - 57 Kg (Approx.)(vii) Per tray weight capacity - 300 Kg(Min)Technical specification of the system:-(viii) Tray Quantity : 32 Nos.(ix) Usable net load - 9.6 ton(Min)(x) Storage surface area per system - 39.2 sq mtr(Min)(xi) Door - Automatic, (xii)Power supply - 440V, 50/60 Hz, 3 Phase(xiii) Motor 3 Phase 1440 RPM - Seimens make or equivalent(xiv) Chain - Diamond makeor equivalent, (xv)Bearing - SKF/NTN make or equivalent(xvi) External cladding - Epoxy powder coatedSafety Features:1. Photo curtain at access port, 2. Motor Protection relays, 3. Limit switch at door, 4. Single phase preventer,5. Switch mode power supply, 6. 15 Min battery backup for PLC, 7. Noise less than 60db, 8. Emergency stop various safety alertsNote: 1) The system and software provided under this item shall be of same make as for item 13.066 to 13.069 or a compatible system and software as recommended by the chosen manufacturer of ASR system. This system shall be integrated with ASR system.2) Comprehensive maintenance of the system during two years of defect liability period shall be a part of this item and rates shall be quoted accordingly. Comprehensive maintenance shall include all spares including software update. The ASR and advanced management system shall be operated by single warehouse management system.3) The PLC program backup for the ASRS and Advanced Inventory Management System shall be provided in an editable format. The WMS program shall be provided along with its source code to enable the user to perform maintenance, modifications and future upgrades as part of the project acceptance 84 Supply, installation and testing of Car Traffic Boom Barrier 6 mtr suitable to working on power supply 230 Volt, 50 Hz, 24V DC electric motor, adjustable with CAMS, operating ambient temperature from -20 to +55 Degree Celsius, uses cycle 2000/Day, air cooling, type of beam is rectangular with skirt, effective torque 280-290 Nm open/close time 2 to 4 Sec complete all as specified and as directed by Engineer-in- charge.Make: FAAC/Parkilo/Skidata/BFT 85 EXTERNAL WATER SUPPLYSupply and fix Foot valve conforming to IS, 100 mm dia complete all as specified and directed. 86 Supply and fix Cast iron air release valve with 100 mm bore and two outlets as per IS:14845 complete all as specified and directed. 87 Supply, installing, testing and commissioning of electrically driven horizontal Centrifugal Pump set 9.0 LPS at 50 Meter Head as per specification, motor TEFC type, 2880 rpm, 415 V, 50 Hz, 3 phase, class F insulation, IP 55 protection, starting on suitable Star Delta starter. The pump shall be horizontal, end suction, top discharge. The pump shall have cast iron casing, cast iron/bronze impeller (as per manufacturer), carbon steel shaft with common base frame (fabricated mild steel channel frame or cast iron type) placed on RCC (1:2:4) including foundation, bolts, nuts etc. complete with antivibrator pad as required capable of discharging not less than 550 LPM at 45 mtr head inclusive of suitable rated three phase starter as recommended by the manufacturer, PVC insulated copper cable connection from starter to the motor terminals all as specified and directed by the Engineer-in-charge.(01 No. Working + 01 No Stand By)Make:- Kirloskar Brothers/Crompton or equivalent. 88 Supply, install, test and commissioning of LT Panel, indoor type, powder coated, 2.0 mm thick CRCA Sheet, CPRI approved having, IP 43, MS angle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with Horizontal copper bus bar for 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2.0 mm thick CRCA Sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. andcomprising as under: LT Panel for Pump House. The LT Panel comprising of the following:- 89 Incoming:-MCCB, thermal magnetic release, 4 pole, 415 Volts, 100 Amps, breaking capacity 36 KA- 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type)- 01 sets(b) Digital Multi function meter - 01 No.(c) CTs - 100/5A, CL-1, 15 VA - 01 set(d) Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 350 Amps for phase and 350 amp for the neutral barOutgoing:-(a) MCB, TPN 40 Amp, 415 Volt, C Curve - 03 Nos.(b) Star Delta starter 12.5 HP, 3 Phase, 415 Volt- 02 Nos.(c) Digital ammeter - 2nos.(d) Single Phase Preventer - 2 nos. 90 M & L Valve chamber of internal size 0.90m X 0.90m X 0.90m (internal dimensions) including excavation of earth work in any type of soil, 150mm thick PCC in 1:4:8 type D2 foundation, brick work in CM 1:6, 15 mm thick rendering in CM 1:4 to internal surfaces and external surfaces upto 150mm depth below GL, PCC 1:3:6 type C1 as in coping, cover with two Nos. of hinges and one No. handle made out of MS round bar 10mm dia with necessary locking arrangement including painting to the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as shown on drg and as specified. Note:- The quoted rate shall include all earthwork and connected items. 91 M & L Earthing complete with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron strip of size 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanized iron steel all as shown in Electrical Plate No. 3 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessary test on completion all as specified and as directed. 92 EXTERNAL ELECTRIFICATIONM & L for HT/LT MS cable route indicator, engraved the description on the disc not less than 6 dia welded with 40x6xmm MS strip of approx length 90 cm duly painted on the steel parts as per colour code and provision of PCC 1:4:8 type D-2 using 40 mm grade stone aggregate of not less than 0.05 cum in each at base under the ground including necessary earth work and formwork complete all as specified and directed.Note: HT route indicator shall be painted as under:-(i) For HT 11 KV cables - “BROWN”(ii) For LT cables - “BLUE” 93 Supply and fix compact air insulated bus bar trunking system with copper busbar 1600 Amps, 50 KA breaking capacity, IP54 protection, bus duct 1600 A, 415 Volt, capacity sandwich type, Set RYBN complete with accessories such as flange ends, vertical bends, supporting brackets etc from transformer to LT panel board complete all as specified and directed. 94 Supply, install, testing and commissioning of Distribution transformer step-down Level 2 (Previously EE Level 3 before Amendment No 4 to IS 1180), 11KV / 0.433KV, Three Phase complying withIS: 1180/IEC-76(Part-1) 2014 with latest amendments, indoortype double copper wound suitable for 50 Hz system of capacity 800 KVA, oil immersed naturally cooled delta connected on HT side and Star connected on LT side, Vector Group Dyn11, provided with OFF load tap changer to vary secondary voltage from -7.5% to + 7.5 % in step of 2.5 %.Losses should be confined to the limits specified as follows: maximum allowable losses atfull load (100 %) & Half Load (50 %) shall not be exceeded 5838 watts & 2147 Wattsrespectively as per GRlHA RATING, Percentage Impedance: 4.5%. Losses and Impedance are subjected to tolerance as specified in IS 1180. The transformers should be supplied with first filling of oil confirming to IS 335. The transformer should have both side cable end box with neutral brought out complete all as directed by Engineer - in -Charge, and installation of transformer shall be carried out as per IS-10028and comprising with the following standard fittings/Technical specifications:-(a) Lifting lug for transformer and tank.(b) Earthing terminal rating and diagram plate.(c) Air release device.(d) Oil filling inlet pipe with plug.(e) Drain outlet pipe with brass gate valve.(f) Conservator tank with oil level indicator(g) Silica jel breather(j) First fill of oil upto level including conservator tank with fresh new oil conforming to IS335.(k) Type of connection Delta/Star(l) Type of cooling: Oil and Natural Air.(m) Vector group: DYN 11.(n) Temperature rise over an ambient of 50 °C maximum.(o) Cable end box on both side for HT/LT cables of suitable size.(p) Provision of thermometer with pocket.(q) Provision of oil and winding temperature gauge. 95 Supply, install, test and commissioning of LT Panel, Indoor type, powder coated, 2.00 mm thick CRCA Sheet, CPRI approved having, IP 43, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal copper bus bar for 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air.The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 1.6 mm thick CRCA Sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. andcomprising as under: The LT Panel comprising of the following:- Main LT PanelHorizontal copper busbar for 3 phase, 440 volts, 50 Hz, 4 wire system of rating 1600 Amps for phases and 1600 Amps for Neutral. 96 Incoming:-Incomer:-ACB 4 Pole, 415 V, 50 KA with Thermal Magnetic Release (Manual Draw out type) of capacity 1250 AmpMetering Unit:- (a) R Y B Indications (LED Type)- 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 1600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 630 Amps, Ics =100% Icu, breaking capacity 35 KA, Ics =100% Icu- 02 No. (For DG AMF Panel & Spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for APFC Panel & FPB 2 Near bulk Store) (c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 320/315 Amps, Ics =100% Icu breaking capacity 36 KA- 01 No. (for FPB 1 Near Adm Block) (d) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 01 No. (for Existing Load)(e) MCCB, thermal magnetic release, 4 pole, 415 Volts,125 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for FPB 3 Near Auction Disposal Store)(f) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 03 No. (for MT Complex, Watch tower no 2, Guard room)(g) Digital Ammeter with suitable CT for each outgoing 97 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MS angle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.1 (Near Admn bldg) 98 Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 600 Amps for phases and 600 Amps for Neutral.Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for 2nd floor & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 160 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for 1st floor)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 63 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for G floor)( d) Digital Ammeter with suitable CT for each outgoing 99 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air.The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.2 (Near Bulk Store) Horizontal Aluminium busbar for 3 phase,440 volts, 50Hz, 4 wire system of rating 600 Amps for phases and 600 Amps for Neutral. 100 Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type)- 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for Equipment Load & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 125 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Bulk Store)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Watch Tower No. 1)( d) Digital Ammeter with suitable CT for each outgoing 101 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet, duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.3 (Near Auction Disposal Store) 102 Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 200 Amps for phases and 200 Amps for Neutral.Incoming:-(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 125 Amps, breaking capacity 25 KA- 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 200/5A, CL-1,15 VA - 01 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 100 Amps, Ics =100% Icu breaking capacity 25 KA- 02 No. (for Store Dispatch Complex & Spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 03 No. (for Pol store, Auction disposal store, Covered Hard Standing)(c) Digital Ammeter with suitable CT for each outgoing 103 Supply and fixing poly carbonate street light junction boxes IP 66/67 Weather proof suitable for outdoor installation having minimumsize255 x 355 x 122 including suitableCable connecting Terminals, Cable lugs, including provn of one No. MCB SP 6 Amps for operating the street light fittings, Suitable Cable Glands as per site requirement, all as directed by the Engineer-in-Charge. 104 S & F Street light bracket made out of GI tubing 32/40 mm dia, light grade of length1.2 mtr long bend to shape suitable for security light fitting with necessary MS clamp-02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers and 3 core FRLSinsulated sheathed, multistranded copper conductor of size 1.5 sqmm for phase and neutral and 1.5 sq mm for earthing drawn throughthe poles for connection from junction box to light fitting complete etc all as specified.Note: Phase should be Red/Yellow/Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase and neutral and one run of cable for earth will be measured and paid as one unit length. 105 Supply and fixing of LED flood light, 200W, watt 230 V, AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp and made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP protection incl system efficiency >110/120LPW 10KV SPD included Energy saving, environmental friendly and general purpose lighting complete all as specified and directed Engineer-in-Charge. Make : Make : Crompton/Philips/Wipro/Bajaj 106 Supply and fix High Mast Panel outdoor type, suitable to take load up to 6 KW, Conforms to IS/IEC 60947-4-1, Provided with Protection Degree IP 54, Extended wide band (150 Vac - 300 Vac) coil, FRLS (Fire retardant low smoke) Internal wiring, In-built Short-Circuit Protection, Class H Insulation, 3 Phase 415 Volts AC with the following accessories:Phase : 3 Phase, 415 VoltsMax Load Capacity : 6 KWTimer type: AstronomicalContactor Rating : 32 A TPMCB Rating : 63 A TPNMake : Crompton/ Philips/Wipro 107 Supply and laying DWC (Double wall Corrugated) duct pipe outer dia 63 mm and inner dia 50 mmconforming IS 16205 (Part 24 ) for protection ofelectric cable complete all as specified and directed. ( for 10 sqmm St light cable & 16 Sqmm cable) 108 AVIATION OBSTRUCTION LIGHTSupply and fix aviation obstruction light integral aviation light comprising of aluminium housing with polycarbonate enclosure, 240 volt with timer switch and one No.10 A, MCB, SPN 230 V with fixed enclosure complete all as specified and directed by Engineer-in-charge.Make:- Bajaj cat No BGAV 302 LED or equivalent in Philips/Crompton/Surya 109 INCINERATORSupply, fixing and testing and commissioning of Solid waste Electric Incinerator, single chamber type having a combustion chamber supported with electric coil for generating sufficient heat to burn 100Kg/hr solid waste, retains and re-burns the exhaust gases for minimum of 2 seconds at 850°C, Stainless steel stack for longevity, fitted with a Velocity Cowl as standard, Chamber designed for maximum air flow and circulation which in turn improves efficiency and total burn time, easy to open and close loading door, designed to increase operator safety, steel cladding to reduce risk of infection and increase longevity of system with working temperature not less 450 degree Celsius mounted on foundation as recommended by OEM including electrical control panel with suitable size MCCB, relays & contactor recommended by OEM complete all as complete all as specified and directed.Note:(a) The electrical works including electrical LT panel, internal wiring of the LT panel, suitable size copper wires from panel to Solid waste Electric Incinerator as recommended by OEM to operate the Solid waste Electric Incinerator of capacity 100 Kg/Hr to make Solid waste Electric Incinerator operational is deemed to be included in the rate quoted. (b) All Electrical works shall be carried out as per relevant BIS/lS equivalent standard norms only and also in accordance with the latest edition of the Indian Electricity Act / rules formed there under and as amended from time to time.(c) Any other works (mechanical, electrical & Civil) connected to installation, testing & functional requirement of Solid waste Electric Incinerator of capacity 100 Kg/Hr all as mentioned above and which is not mentioned or included in this Schedule but required at site necessary shall be carried out by the contractor and quoted rate shall deemed to included for the same.(d) Foundation/Plinth/Base: shall be provided as per manufactures recommendations, however minimum 0.5m space should be available all around the Solid waste Electric Incinerator and height of plinth shall not be less than 0.5 MMake: Precitech thermal Pvt. Ltd., Rram Buisiness corp, Alfa therm Ltd., Thermax Ltd, Kanti Industries, Fortec 110 Supply & fixing MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, breaking capacity 36 KA- 01 No.Ics =100% Icu with Sheet metal enclosures fixed properly at directed location and connecting/testing complete all as directed. 111 ELECTRIC SIRENSupply and fixing Sirens Electronic type Horizontal Double Mounting Three Phase 400/440V, 2800 RPM 50 C/s Flame Proof, audible range 3.5 Km, 2 HP, continuous normal operation for at least 50 minutes with on/off system complete all as specified and directed. 112 Supply and fix advance Sirens controller Electronic type suitable to operate on 3 phase, 415 volt AC 50 Hzcomplete all as specified and directed. 113 Supply & fixing MCCB, thermal magnetic release, 4 pole, 415 Volts, 63 Amps, breaking capacity 25 KA- 01 No.Ics =100% Icu with Sheet metal enclosures fixed properly at directed location and connecting/testing complete all as directed. 114 SOLAR POWER PLANTDesign, supply, installation testing and commissioning of roof top solar photovoltaic power plant (ON-GRID) on roof top of existing bldg of capacity 150 KWp, power evacuation at 415 Volt 3 phase system all as per guidelines/norms issued by MNRE & Indian Metrological Deptt approved Solar Radiation Data viz Direct Normal Irradiance, Global Horizontal radiance etc complete comprising with the following Solar Photo Voltaic Plant.(a) Design, supply, installation, testing and commissioning of Solar PV Modules capable of generating 150 KWp (AC) electricity at 415 Volt 3 phase system. These Solar PV Modules of 540 watt PERC with a modular efficiency of 17-19.84% as per IEC and MNRE standard or as per approved design parameters with Poly/Multi Crystalline Silicon Solar cells of minimum wattage of 540 watt with minimum 144 cells & efficiency not less than 17 -19.84%, conforming to IEC 61215, IEC 61730, IEC 61701. Solar PV Module should be of approved Indian Brand only and Qualify under the Domestic Content requirement (DCR) norms of NVVN/SECI and testing requirement fixed by MNRE. The PV modules shall be warranted for a period of minimum 25 years, Solar PV modules used in system shall be warranted for their output peak watt capacity, which should not be less than 90% at the end of Ten years and 80% at the end of Twenty Five years. Each Solar PV Module must use RF identification tag. The following information must be mentioned in the RFID used in each module:Name of manufacture of PV module, Name of manufacturer of Solar cell, Month & year of manufacturer (for solar cell and module), Country of origin (lt is mandatory to use cells and modules manufactured in India). I-V curve of the module, Wattage, LM, V-M, & FF for the module, Unique Serial No & Model No of the module, Date & year of IEC PV qualification certificate, Name of the test lab issued IEC certificate. The PV modules used in the solar power projects must qualify to the latest edition of the following International Electro technical Commission (IEC) P module qualification test or equivalent BIS Standards. The PV module must be tested and approved by one of the IEC authorized test centres. 115 (b) Material and labour for Module Mounting structure (MMS) fabricated from hot dip galvansied iron section of suitable size with specified tilt angle according to site requirement & optimum angle to achieve maximum benefit of solar energy and suitable to withstand 180 Kmph wind speed all as per approved design parameters as per MNRE standards and to match with the existing site conditions. Necessary roof treatment to avoid any seepage in future shall be done by the Contractor and the amount included in the rate quoted. The roof tiles shall be dismantled and refixed back in original position. Structure shall be built with brick masonry basement of adequate size as per direction at site including all necessary civil work required for the foundation.(c) Supply, laying & Testing of DC cable minimum size 4/6sq mm multi stranded copper conductor, conforming to relevant IS, weather proof UV resistant with operating temperature up to 120 degrees, minimum rated voltage 1100 volt for inter connection of SPV Modules to array junction box including suitable size of cable lugs, male & female MC4 connectors & joints etc.(d) Supply, installation test and commissioning of protection devices MCCB 400 A, isolator and three phase 4 wire LT energy meter, array junction boxes having rating 150 KWp with over voltage protection and surge protection.(e) Supply, installation, test and commissioning of Grid tie Solar Power conditioning unit / inverter of minimum capacity 150 KWp(DC to AC 415 V in Three phase system) all as per approved design parameters & capable of generating output voltage 415 V AC at rated load condition with efficiency not less than 98 %, conforming to IEC 600682-2 NDE standards with power reduction, LVRT with protections for anti-islanding, Ground fault monitoring, Grid Monitoring, AC & DC Over voltage and under voltage protection, AC & DC short circuit lover current protection and DC reverse polarity protection, graphic display etc. all as specified and as directed.(f) Material and labour for Earthing for Lightning protection for SPV modules etc as per IE rule, MNRE guide line & BIS all as per approved plan complete with galvanised earth plate electrode 600x600x6 mm thick buried directly in ground vertically (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connected to and including Gl strip 32x6mm size protected with Gl medium grade pipe 40mm dia for earth electrode up to test point by means of GI nuts, bolts, check nuts and washers including earth work excavation, PCC (1:3:6) type Cl pit and RCC cover ( 1:2:4) type Bl and funnel, with necessary charcoal, salt etc complete. 116 (g) Supply and fixing aluminium strip of size 25 x 3mm thick for roof / down conductor fixed on insulators/ saddles of suitable size for SPV modules lightning protection upto interconnection between Roof top LA to Ground Earthing system. (h) AC Cable: Supply and laying of 150 Sqmm LT XLPE insulated, screened PVC bedded, sheathed with multi-stranded aluminium conductor armoured with galvanised steel wire 1100 volts grade heavy duty conforming to IS 150 Sqmm x 3.5Core as per site requirement.Note (i) :-(a) Before quoting the bid, Contractor or his authorised Engineer/consultant must visit the proposed site to study the site condition.(b) Before commencement of work, contractor shall submit drawings & lay out plan with scale including required qty to Accepting Officer for approval.Note(ii):-(a) The mechanical structures, electrical works and overall workmanship of the Grid solar power plant must be warrented for a minimum of 5 years.(b) All Mechanical, Electrical works shall be carried out as per relevant BIS/lS equivalent standard norms only and also in accordance with the latest edition of the Indian Electricity Act / rules formed thereunder and as amended from time to time.(c) Any other works (mechanical, electrical & Civil) connected to installation, testing & functional requirement of solar photovoltaic power plant of capacity 150 KWp (AC) all as mentioned above and which is not mentioned or included in this Schedule A but required at site necessary shall be carried out by the contractor and quoted rate shall deemed to included for the same(d) Contractor shall provide adequate Spares/items required for minimum period of 1 year maintenance including DC & AC items under scope of work.Note (iii) : Design report shall be submitted before execution of Work at site by the contractor toGE for his scrutiny / comments and futher submitted to AO for obtaining approval. 117 DG SETSupplying, installing, testing and commissioning, factory assembled silentDiesel Engine driven generator set, fully wired alternator AC to give an out put of 400 KVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hzsupply, 1500 RPM, directly coupled with diesel engine liquid cooled mounted on common base frame complete with floor mounting fuel tank (service tank) of adequate capacity with fuel line & accessories, PCC foundation work as per manufacturers instructions, vibration damper pads, control panel & other accessories etc and comprising of following.(a) Diesel Engine: Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500 RPM under NTP conditions of BS 5514 and conforming to IS 10001/ 10002, DIN 6271 & ISO 3046 with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories: Diesel engine of rated speed at full load electric start developing with system with radiator and including electronic governor control of class A1, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries ofadequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/flexible coupling and coupling guard complete.(b) Radiator with blower fan or heat exchanger with guard.(c) Pipe coupling for engine cooling system piping.(d ) Corrosion inhibitor coolant(e) Paper element filters(i) Fuel filter(ii) Lube oil filter(iii) By pass(f) Fly wheel housing and fly wheel to suit alternator.(g) Engine bearing mechanism in fly wheel housing.(h) Shut off coil with safeties for LLOP/HWT/over speed.(i) Dry type air cleaners and vacuum indicators.(j) Residential silencers.(k) Stainless steel exhaust flexible bellows. 118 (l) Battery charging alternator.(m) Exhaust piping made out of STIC C class, MS pipe inclusive of all accessories and hardware, necessary supports scaffolding as per manufacturers recommendations to sustain back pressure with rain cap.(n) Mineral wool insulation 2 inch thick suitable for 400 degree Celsius temperature cladded with aluminium sheet of30 gauge for the entire length of exhaust pipe.(o) First fill of oil, coolant and diesel during commissioning and 12 hours testing.(p) Interconnecting copper cabling of adequate capacity batteries control.(q ) Fuel pipe class STIC 1 /1.5 /2 dia - 01 lot(r) Self starter 24 volts DC.(s) Electric operated electronic governor.(t) Fuel injection pump.(u) Electronic instrument panel, complete with all accessories as per manufacturers specifications displaying the following:-(i) 12vx2 nos -24V Battery. (ii) Water temperature.(iii) lubricating oil pressure.(iv) Engine speed -1500Rpm(v) Engine hours(vi) Frequency.(vii) Voltage.(v) Safety control (Trip and indication).(i) High water temperature(ii) Low lube oil temperature(iii) Overspeed stop 119 (w) Base frame: Sturdy, fabricated welded construction, channel iron base frame (duly painted) for mounting engine and alternator as per manufacturers design alonwith AVM pads.(x) Battery:-24 volts(2x12v Battery) DC, 180AH, maintenance free battery conforming to IS:14257 with leads & terminals (Make- Excide/Amron).(y) Fuel tank:12 hrs. full load diesel storage capacity fuel tank with mounting brackets factory made of 5mm thick HR/MS sheet with level indicator fuel inlet, fuel outlet, air vent, drain plug, inlet arrangement for diesel filling for exterior canopy (without opening its panel) etc complete all as specified and directed.(z) Isolator panel with 630 amp MCCB(aa) Auto logic panel for automatic stat(ab) Alternator: Alternator suitable rated for 400 KVA, 0.8 pf , 415 volts, 3 phase, 4 wire, 50 Hz at 1500 RPM, self excited and self regulated with AVR brushless, screen protected, drip proof, insulation class-H, IP -23, voltage regulationgrade - VG 3 self ventilated and conforming to BS: 5000 / IS: 4722 suitable for engine as mentioned here-in before, conformig to IS: 13364(part-1)Make: KOEL GREEN / stampford/crompten/kirloskar/Greaves(ac) Acoustic Enclosure:- M & L for acoustic enclosure for the above 400 KVA DG set to reduce noise level to 75 dB measured at 1.0 meter distance for audible frequencies as per guide of Central Pollution Control Board andmanufacturers specification and comprising of following from authorised GOEMs of Gen Set manufacturers specified :-(i) Sound insulation : 100mm thick Rock wool (Density 64 Kg/Cum).(ii) Outer body : 1.6mm thick CRCA(iii) Door : 1.6mm thick CRCA(iv) Base frame : ISMC 300(v) Inside illumination : 1 No.- 1 x 18 watt LED fitting of make Phillips/ Bajaj/ Crompton.(ad) AMF Control panel:- Factory fabricated cubicle type, free standing, floor mounted, indoor type, IP-43, AMF control panel, provided with removable rear panels & hinged front panel for easy accessibility, fabricated out of not less than 2.0mm thick CRCA sheet including two coats of powder coated paint over a coat of red oxide primer etc and comprising of following: 120 (ae) AMF control circuit with 4 pole MCCB 630 Amps - 2 nos, with ultimate breaking capacity Icu-50 KA at 415 volts and microprocessor release conforming to IEC 60947 Part-I with breaking capacity Ics=Icu at 415 volts , thermal overload setting 70% to 100%, short circuit setting 5 to 10 times-02 Nos. for main supply & DG set supply with HRC back up fuse complete with all DC control relays/ Line voltage monitor (LVM) as per OEM specifications incorporating motorised stored energy operating Engine start, stop, three attempt starting facility and failure to start etc.(af) Digital load manager : Three phase 4 wire indicating V,I,PF, KVA, KW, F of Enercon make with serial communication port model No. EM6400 with class 1.0 accuracy meter or equivalent make suitable rating of CT per phase- one No.(i) Indication lamp R, Y, B with 3 Nos. of 2A HRC fuses-10 sets.(ii) Bottom gland plate for incoming and outgoing cables.(iii) Circuit diagram plate.Note:- DG set should be as per CPCB- 4 latest norm wef 01 July 2023 of National Clean Air programme (NACP) Act 1981.The contractor shall procure the item within the period given by CPBC in case of revision in CBPC norms. Nothing extra will be paid on account of delay from the part of contractor. DG set shall have an exhaust with stack height of minimum 2m from the top of generator with a cowl. Smoke released from the exhaust of the DG sets indicating that emission parameters are within permissible limits, as prescribed by CPCB, demonstrating compliance with emission limits prescribed by CPCB 2016. 121 Supply, install, test and commissioning of LT Panel, Indoor type, powder coated, 2.00 mm thick CRCA Sheet, CPRI approved having, IP 43, MS angle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natuaral flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 1.6 mm thick CRCA Sheat duly compartmentalised for each control gear with louvers and air vent gasket for natuaral flow of air and suiatable provision to accomodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.1 (DG Panel ) 122 Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 630 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 800/5A, CL-1,15 VA - 1 set(d) Horizontal aluminium bus bar for 3 phase 440 V, 50 Hz, 4 wire system of rating 800 Amps for phases and 800 Amps for neutralOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, Ics =100% Icu breaking capacity 36 KA- 03 No. (for Package AC Bulk Store, pump house and fire pump & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 160 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Pump House & Fire Pump)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 80 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Incianator)(d) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 07 No. (for Terrace pump 1, Terrace pump 2, Power House, High mast 1, High mast 2, Street Light)(e) Digital Ammeter with suitable CT for each outgoing(f) Astro Time switch for 3 phase 20A- 1 No(g) 3 Phase Power contactor 20 amps, with 230 coil 123 SEWAGE DISPOSALM & L for laying of DWCPE sewage pipes line 200 mmdia borepipe sftiffnessclass SN 8 includingsealing of joints fittings etc complete with collers complte all as spcified and directed 124 M & L for laying of DWCPE sewage pipes line 150 mmdia borepipe sftiffnessclass SN 8 includingsealing of joints fittings etc complete with collers complte all as spcified and directed 125 COMPOUND WALLS & F Concertina Coil of 600/700 mm outer dia made out of 2.60 mm dia spring steel wire dipped in corrosion preventive fluid (rusilo 901) of castrol make each coil having min 50 turns (circles) covering 6 m and an average weight not less than 8.57 Kg (plus or minus 5 %) incl handle and spike at both ends of coil erected in position on top of mild steel angle by fixing with 1.70 mm GI wire for securing, coil with fish hook bars, incl necessary welding to MS Sections etc all as specified and directed. 126 GREEN BUILDING NORMS(GRIHA CONCEPT)Supply and Install Organic Waste Converter fully automatic having capacity 50Kg/day, having internal tank made of high quality stainless steel while external panels are powder coated for enhanced product life with necessary electric control panel, cabling necessary civil works for installing machine etc with following requirements:-Type of machine: Fulley automatic in-vessel composterComposting method: 24 Hrs. Micro-organisms-based compostingmachine Type of microganism used: Heat resistant thermophilic bacteria Final Output: Dry organic Soil conditioner/Soil supplementsCycle time: 24Hrs Volume reduction in 24Hrs: 80-85% Internal tank: Stainless steel type Main agitator Shaft: Stainless steel type Input voltage: 415VSpecial features: VFD as standard across all models, Touchscreen standards Daily waste processing: 150Kgs Rated capacity: 7KWPower consumption (KWH par cycle): 13-15Length: 1650, Width: 850,Height: 1455 127 Supply, installation, testing and commissioning Three phase energy meter with the following specifications: Microprocessor based three phase, smart electricity meter, equipped with a bi-directional cellular (NB-IoT) communication that allows it to interact with the head end system (HES) for data collection and configuration with adequate security including electronic static pre paid cum postpaid energy meter rating 415 Volts, 50 Hz of range 10-100 Amps, complying to IS16444:2015 (reaffrimed 2020) and conforming to IS 3779 with LED display and parameters like Voltage, Current, Frequency, Power, Power factor, KWH/KVA, default in built dual source, inbuilt long range (LORAWAN) Communication suitable for outdoor LoRa data accumulator and also compatible for Prepaid and Postpaid online energy monitoring billing system with disconnection /reconnection through remote software / data export to ERP complete with 5 Years warranty.Note:(a) The Energy Meter to be capable of running in both prepaid and postpaid mode.(b) The meters to carry 5 year warranty. (for entire system) 128 Supplying, Fixing, Commissioning and testing of configuration of cloud Hosted multi user web based software with following modules:(i) Head End System (HES): to acquire meter data automatically from DCU sand monitor parameters acquired from meters.(ii) Meter Data Management ModuleThe meter data management module would be responsible for collecting the data from the data concentrator and make the data available to the billing system. The system would support offline meter(a) 30 min instantaneous data from all the meters for seven parameters Cumulative Energy. Cumulative Apparent Energy (as applicable), Power, Current, Voltage, Power Factor and Frequency(b) Monthly billing survey data for cumulative energy and max demand(iii) Billing Module: The billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and make energy data/billing data available to admin and end users. The billing module would include functionalities for tariff setup, bill format setup, bill adjustment, occupation billing and vacation billing. It would allow postpaid and prepaid functionality as required.(iv) Occupation and Vacation Module: The system would support occupation/vacation based on the unit catagories. The system would support automatic data capture on occupation and vacation events.(v) Website: There would be a dedicated website forAGE/GE and BSO team to view all the data and information alongwith customer portal for use of customer. The designated users in MES would have the admin access to the application. The MES Staff would also have the access to the key information on mobile App (AndroiandiOS based) for admin use complete all as specified and directed.(vi) Customer Module: The system would include a customer portal for the resident/occupants to login and view their own energy /billing data and recharge facility. There shall be consumer App (Android and iOS based) also to log in and view their own energy/billing data and recharge facility.(vii) Communication Module :The system would provide communication of energy data and bills via print, email and sms methods. 129 (viii) Meter Master Data: The system would support meter data repository. The system would support meter replacement process.(ix) Excel Export: the system would support export of metering and billing data in excel and pdf format.(x) Energy Accounting module: The system would include features of energy accounting, the system would to able to account for total energy block wise, facility wise and would also allow calculations of the unaccounted energy in case total energy meter is also available.(xi) Prepayment/Recharging Facility:The system should periodically monitor the energy consumption of prepaid consumers and decrease the available credit based on the consumption. The system should allow online/digital recharging through consumer App (Androidand iOSbased) and Web portal. The configuration and necessary arrangement for payment gateway and E-MRO facility shall be deemed to be included in the quoted rate. The system should sendconnect/disconnect command on the basis of available credit.Low credit alarm: The system will give an alarm over the consumer App and SMS to the registered mobile number in case the credit in the meter goes down be low apredefined limit.Emergency credit: The meter will work even when the credit falls down to zero to prevent disconnection. This limit shall be configurable. The system should support happy hours inorder to prevent disconnection in non working hours and on holidays. The Happy hours should be configurable complete all as specified and directed. 130 Supply, Installation, Testing and Commissioning of DCUs/Gateways and the arrangement of Sim cards or Internet to enable reliable medium for two-way communication between Smart Meter & HES. The data acquisition (Push/Pull) frequency shall be, configurable. It shall push events such as tamper, power off etc. to HES immediately on occurrence/receipt from meters. It shall have provision for the cellular, WiFi and Ethernet communication for the backhaul to HES. It shall be capable to handle data of minimum 1000 Nos. of any type of smart meter (1ph/3ph).It shall be able to communicate with the nearest meters at a distance of at least 500 m, depending on topographical features. Communication of the nearest meters with other meters shall be established through appropriate mesh formation. RF Mesh shall support self-forming and self-healing features. The equipment shall be weather proof and dust proof (minimum rating: IP54 for indoor and IP65 for outdoor installation). It shall have rechargeable battery with backup for 1(one) hour for normal meter reading, to push tamper event, carry out on demand reading, etc complete all as specified and directed. 131 Hosting GPRS (4G) charges for Gateway for five years from the date of completion F Including 2 years waranty and 2 years Maintinance after warranty) Make:-Airtel/Jio/Vodafone 132 Supply and installation of digital Water flow meter 50mm suitable for domestic and commercial applications complete all as specified and directed. 133 Supply and installation of digital Water flow meter 40mm suitable for domestic and commercial applications complete all as specified and directed. 134 ARBORICULTUREM & L for excavation of pits size 30cm x 30cm x 30cm in loose soil and filling the pit with mixture of river sand and approved top soil in the proportion of 1:3 mixed with 30% of cow dung powder, 100gms of bone meal and 100gm of neem cake powder 135 All as per item No 13.121 above but pit size 60cm x 60cm x 60cm 136 Supplying and planting red palm or royal palm healthy sapling having 45cm height and shall have a minimum height of 65cm after 6 months 137 Supplying and planting coconut tree healthy sapling having 75cm height and shall have a minimum 95cm after 6 months. 138 Supplying and planting flower plants(Champa/ hybrid hibiscus/ Hybrid west Indian Jasmine/ Hybrid Plumeria white plant/ Panama yellow plant/ Oleander) healthy sapling having 10cm minimum height and shall have a minimum 25cm to 30cm height after 6 months. 139 Supplying and planting phylanthus healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 140 Supplying and planting bougainvillea colour flower plants healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 141 Supplying and planting song of India flower plants healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 142 Supplying and planting dracaena flower plants healthy sapling having 15cm to 30 cm height and shall have a minimum 60cm height after 6 months. 143 Supply and planting mexican grass including providing manure as directed. 144 PILE FOUNDATIONBoring 450 mm dia piles to any depthin any type of soil/ strata by anyapproved method, complete all as shown on drawings and as specified anddirected.Note:- The quoted rate shall include for mobilization and demobilisation of piling equipment, making approaches to site or point of pile boring if necessary. Nothing extra shall be paid on this account. 145 Boring for bored cast in situ pile 600 mm dia to any depth through any type of soil / strata, using DMC method (Direct Mud Circulation)and getting out & disposal of spoil to any distance outside of MD land , complete all as specified and as directedby the EngineerIn Charge 146 M & L Reinforced cement concrete of grade M-35 design mix (RMC) as per IS-456using 20 mm graded stone aggregate in cast in situ DMC bored pile of any length / any sectionscomplete all as specified and as shown on drg 147 M & L Reinforced cement concrete of grade M-35 design mix (RMC) as per IS-456using 20 mm graded stone aggregate in pile caps / grade beams complete all as specified and as shown on drg 148 Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10 mm dia and over for bored cast in situ piles of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with and including 0.9mm dia MS wire (annealed) or welding so as to secure the bar firmly in position/ required shape complete all as specified and shown on drgs (Fe-500D). 149 Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10 mm dia and over for pile caps and grade beams, cut to length, bent to shape required, hooking ends and binding with and including 0.9mm dia MS wire (annealed) or welding so as to secure the bar firmly in position/ required shape complete all as specified and shown on drgs (Fe-500D). 150 All as per item No 13.136 here-in-before but5mm dia and over upto and including 10mm dia as in helicals for piles and stirrups for grade beams complete all as specified and directed. 151 M & L for providing PCC (1:4:8) type D-2 using 40 mm graded stone aggregate for concrete layer below pile caps foundation complete all as specified and directed. 152 Formwork to sides of pile caps/ grade beams and similar work, rough finished surface of concrete flat all as specified and as directed. 153 M & L for carrying out non destructive integrity test all as per IS 2911 (Part 4) 2013 for 600 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed all as specified and directed. 154 M & L for carrying out non destructive integrity test all as per IS 2911 (Part 4) 2013 for 450 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed all as specified and directed. 155 M & L for carrying out Initial Load test (vertical load test) cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013 including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 156 M & L for carrying out Initial (lateral load test) cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 157 M & L for carrying out Initial load test (pull outtest as per design load) of cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 158 M & L for carrying out Routine load Test (Vertical load)all as per IS 2911 (Part 4) 2013 for 600 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed 159 Testing of piles Initial load test (verticle load test) for 450mm dia cast in situ bored piles all as per IS including removing the testing equipments from the site after testing is completed all asspecified and as directed 160 M & L for carrying out Initial Load test (lateral load test) cast in situ piles of 450 mm dia as per IS 2911 (Part 4) 2013 including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note:- Providing and installing test piles shall measured and paid separately) 161 M & L for carrying out Initial load test (pull outtest as per design load)of cast in situ piles of 450 mm dia as per IS 2911 (Part 4) 2013including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 162 M & L for carrying out Routine load Test (Vertical load)all as per IS 2911 (Part 4) 2013 for 450 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed

BRR : 11403991 Purchase Of Psychology Equipment , Aesthesiometer (Divider Typ) (Two Point, Graduated Aesthesiometer,All Metal Electro Plated) , Colour Mixer (Also Called Colour Wheel) (Electrically Operated. Variable Speed. Used For Study Of Visual Phenomena Of Colour Perception Of Complementary And Non-Compelmentary Colour Development) , Colour Contrast Apparatus (Different Colour Plates Are Used To Show The Phenomenon Of Colour Contrast. An Indispensable Apparatus To Introduce The Said Phenomenon.) , Successive Contrast Or After Image Apparatus: (The Phenomenon O£ After Image Can Be Studied. The Apparatus Is Handy, Well Furnished And Provides All Materials Required For Studying The Said Phenomenon.) , Depth Perception Apparatus:(The Box With 3 Needles Provides Enough Room For Studying The Depth Perception With Electric Bulb.) , Lifted Weights Set (Metal): (A Set Of 12 Metal Tubes With Removable Or Fixed Tops Containing Certain Weights. Fine Finish And Superior Quality. This Is Required In Weight Discrimination Experiments In Psychophysics For Differential Limen (Dl), Upper Differential Limen U Dl), Lower Differential Limen (Ldl) Determination.) , Muller-Lyer Illusion Figure (With Stand & Scale): (A Study And A Handy Set Of Mullerlyer Illusionfigure. Horizontal Type With A Stand To Adjust The Figure To The Desired Eye Level Of The Subjects. Variable Figure Operated By Smooth Sliding Of The Figure (In Front Of The Experiment) On An Attached Mm Scale. Fine Ficish And Superior Quality Of Work (20‘) , Answer Sheets For Muller- Lyer Illusion (A Pkt.Of 100) , Size-Weight Illusion (Collins-Drever Model) (A Set Of 24 Tubes With Two Standard Stimuli Of Different Weights. Fine Finishing And Superior Quality. Supplied In A Wooden Handy Box.) , Vertical Horizontal Illusion. (T And L Forms With Stand And Scale.) , Optical Illusion Chart:(Cloth Bound Showing Fifteen Well-Know A Illusion, Five Each Of Extent, Direction And Perspective.) , Phi-Phenomenon Apparatus: Electronics.(Consists Of Two Lights Holding Small Cabins With Variable Positions And Time Exposures. Requires Marcury Cup Metronome Also, If An Automatic Operation Of The Apparatus Is Desired.) , Perception-Influence Of Set:(Two Sets Of 12 Cards, Each Of Which Contains A Pair Of Geometrical Figures. One Series Introducing A Set And The Other Serving As An Experimental Series Ideal For Studying Influence Of Set) , Visual Space Perception Apparatus:(Consists Of Well Polished Wooden Box(Size: 30X12X L9J. Having Two Fixed Lights And A Third Movable One With Slides In The Box Perpendicular To The Plane Formed By Tbe Two Fixed Uprights. A Fixed Scale On Top Of The Box Enables One To Find Errors. The Inside Of The Box Is Illuminated By Means Of Two Lamps. Viewing Slit Is Provided On The Smaller End.) , Vase And Face Figures. (In 5X 5 Size On Sturdy, Iraported Card Board. , Galton Bar: (It Is One Of The Early But Still Very Popular Psychophysical Experiments To Demonstrate The Problems Of Subjective (Psychological) Equality. , Whipples Weight Box: (Consists Of 2 Standards And 20 Comparison Weights. The Weights Are Made Out Of Light Metal And Not Of Cardboard As Made By Some Foreign Firms. Supplied With An Attractive Box Lined With Velvet To Hold Weights In Individual Compartments) , Shape And Size Discrimination Apparatus:((T.K.K. Japan Model) This Device Examines The Subjects Size Discrimination Ability Relying Upon Visual And Tactile Sensations As Well As Speed Of Shroting. The Subject Inserts 50 Small Discs Or Coins. Which Are Different In Size And Thickness In Five Different Ways, Into The Corresponding Slit Of Holes As Fast As Possible. The Practice Is Allowed Only Five Times And The Test Is Repeated Twice.) , Colour Preference Cards:(A Set Of 8 Cards Of Different Colours.Can Be Exposed Through The Gravity Tachistoscope) , Colour Preference Wheel: Colour Preference Wheel:(Used For Colour Preference. Using Pair-By-Pair Comparison Method Colour Reference Wheel Is Operated.) , Conflict Board:(With Step Down Transform Mer And A Pad Of 84 Sheets Along With Manual For Demonstrating Experimentally The Reactions To (1) Approach-Avoidance, (2) Approach-Approach, (3) Avoidance Avoidance And (4) Double Approach-Avoidance Situations. A) Manual Available) , Card Sorting Square Tray:(A 4X4 Square Tray Has Been Specially Designed To Eliminate Space Error On Changing The Position Of The Tray. The Pigeon-Hole Numbers Can Be Changed Into Four Different Patterns Simply By Changing The Position Of The Movable Plywood Back Of The Tray, Fine Finish And Superior Quality Work.) , Electric Maze (Human Maze ):(Two Desig Ns On The Same Maze (One For The Experimenter And The Other For The Subject Alternately). Teak Wood, Light Or Sound Signals For Count Ing Errors. Impulse Counter Can Also Be Used. Specially Planned According To The Designs Of The Mazes To Plot The Procedure And Progress Of Learning From Trial To Trial. 420 Points. With Manual. (A)Ebonite Stylus (B)Electrically Operated (C)Electrically With 6 Digits Error Counter (D)Electronics With Digital Timer & Counter. (E)Record Blanks.For Mazes 1 And 2, (A Pkt. Of 100) , Electric Maze Witb Stylus (Human Maze):(Finished With Good Polish, Having 219 Contacts And A Binding Post. Supplied With Stylus.) , Learning By Recognition Method:(A Set Of 35 Cards With Instruction Sheets.) , Slot Maze:(Designed Completely Controlled) , Memory Drum:(Electrically Operated, Four Variable Speed, High-Quality) , Immediate Memory Spantest:((English): (A)Form A (A Pad Of 100)(B)Form B (A Pad Of 100 ) (C)Manual) , Mirror Drawing. (Apparatus: Size 15X 12” X 3/4 Folding Type. Plywood Surface With Hard Plastic Base To Assure Smooth Movement Of The Stylus On Which The Metallic Pattern Is Fixed. For The Electrical Operation, Over All Body Is Made Of Plywood. With Manual: (A)Electrically Operated (B)Electrically With 6 Digits Error Counter (C)E1ectronics With Digital Timer & Counter.) , Mirror Drawing Apparatus: (For Hand Operation, With A Wooden Cover And Star Sheets.) , Short-Term-Memory Test By C.B.Dwivedi (English) ((A)Manual (B)Cards Of Ccc Trigrams (A Pkt. Of 15) (C)Cards Of Meaningful Triads (Pkt.Of 15) , Long-Term Memory Test By C.B. Dwivedi (English):((A)Manual (B)List Of Words For Recognition Test (A Pkt. Of 100) , Pyramid Puzzle:(The Pyramid Problem Involves Placing A Series Of Graduated Blocks On One Of Three Posts Such That A Larger Block Is Never Placed Over A Smaller Block. Useful For Demonstration Of Problem Solving. In Sight Learning And Concept Formation. Average Solution Time With New Subject Is About 20 Min. Repeated Trials With The Same Subject Will Produce Successively Shorter Solution Time.) , T-Puzzle:(For Problem Solving Studies. All Made Up Of Plastic, Superior Quality And Fine Finish) , M-Puzzle (For Problem Solving Studies. All Made Up Of Plastic, Superior Quality And Fine Finish.) , Habit Interference Board With Cards. , Conditioned Reflex Apparatus:(A Thick Glass Plate Is Fixed In A Wooden Frame To Which Is Attached A Felt Hammer. The Hammer When Released Will Fly Up And Strike The Glass In Front Of The Eyes Of Subject. This Is Attached To Head Rest And Can Be Adjusted To Any Height. The Apparatus Is Mounted On A Table By Means Of Clamp Supplied With It. Used For Eyelid Conditioning Experiment.) , Pencil Maze:(A Durable Aluminium Maze With A Hard Surface Bottom To Prevent Grooving. Standard 8.5Al1” Paper Placed Under The Maze Produces A Permanent Record Of Subjects Performance. Can Be Used For A Variety Of Learning Problems.Subjects Are Blind Folded When Tracing The Maze. Speed As Well As Accuracy Can Be Studied Witb The Aid Of A Stop Watch Or Clock Timer.) , Human Problem Solving By C.B. Dwivedi (English):)With Instructions,Designof Experiment And Calculation Procedures. May Also Be Used For Studying The Influence Of Set On Problem-Solving. (A)Booklet : (I) 30 Problem Work Sheets (A Pkt. Of 100) (Ii) 6 Problem Sheets For Studying The Influence Of Set (A Pkt. Of 100) (B)Manual , Water-Jar Problem Solving Test By N.K. Jain:(A Series Of 15 Problems Illustrated Jar Wise. This Is Ideal For Studying Problem Solving In Real-Life Setting. Four Problems Introduce The Situation Followed By Difficult Ones. To Be Used For Studying Effect Of Set On Problem Solving (A)Test Booklet (A Pkt. Of 100) (B)Manuai) , Nonsense Syllables Or Meaningless Word Lists (English)(: From 3 To 11 Syllables. Printed On White Paper And Also In List Form (Set Of 3 Pads) , Paired Associates Word Lists (English): (From 2 To 6 Words. Printed On Separate Sheets (Set Of 4 Pads).) , Massons Disc:(Used To Study The Fluctuations Of Attention.) , Span Of Attention Cards.(A Set Of 12 Cards Having Equal Sized Dots (From 3 To 14) Scattered Randomly. With An Instruction Sheet. Ta)Answer Sheet (A Pkt. Of 100) , Doc Figures (Same Dot Figures Are Used In Studying The Phenomenon Of Attention) , Tachistoscope(Jaiota-Gravity Type):( Tachistoscope With Three Different Adjustable Windows. The Tachistoscope When Unfolded Provides An Automatic Screen Between The E And S. All Leak Wood, Fine Gray Paint Or Polish. With Manual) , Tachistoscope(Fall Type):(Can Be Used For The Study Of Span Of Apprehension And Memory. All Teak Plywood Made, Fine Polish Or Gray Paint. Smooth And Comparatively Noiseless Operation Attempted.) , Judging Emotions From Photographs:(A Set Of 12 Photographs.) , Division Of Attention Board Apparatus:(Electrically Operated With Error Counter.) , Colour Preference Cards:(A Set Of 8 Cards Of Different Colours. Can Be Exposed Through Gravity Tachistoscope) , Colour Preference Wheel :(Used For Colour Preference. Using Pair By Pair Comparison Method Colour Preference Wheel Is Operated.) , Vernier Type Chronoscope:(Specially Made Of Heavy Bottom (All Metal) To Prevent Any Accidental Movements.) , R.T. Apparatus:(Giving Choice R.T. Using Two Light Stimuli) , Mental Fatigue Test By N.K. Jain (English):(With Instruction Sheet. (A) Numerical Sheets (A Pad Of 100) (B) Alphabetical Sheets (A Pad Of 100) (C) Instruction Sheet) , Work And Rest Test By M.C. Joshi (English):(A)Alphabetical Sbeets : Form A For Work (A Pkt. Of 100) (C)Numerical Sheets : Form A For Work (A Pkt. Of 100) (C)Manual , Normal Curve Demonstration Apparatus (Laffayate Model)(This Is An Effective Visual Demonstration Device For Showing The Natural Normal Distribution Curve And Illustrating A Graphic Picture Of The Law Of Probability. Marbles Should Be Inserted Through The Hopper To A Preset But Adjustable Position To Produce The Normal Distribution Curve. This Unit Is Ideal Both For Demonstration In Statistics Classes As Well As For Those Experiments Requiriag Assessments Of Normal Probability Phenomena By The Subject. Instruction Manual Is Also Available.) , Teaching Aptitude Scale By Sanjay’ Vohra (English):(This Test Has Ll9 Items. It Measures Aptitude In Eight Areas: Communication, Intelligence,Maturity, Perceptiveness, Persistence, Receptiveness, Social Warmth And Teaching Interest. This Test Is For Teachers And Takes 40 Min To Complete. A) Reusable Booklets (Pkt. Of 25) B) Answer Sheets (Pkt. Of 100)C) Profile Sheets (Pkt. Of 100) D)Scoring Key E) Manual , Duncans Sales Aptitude Test (Indian Adaptation) By Sanjay Vohra (English):(This Test Has Been Designed To Help In Appraising Sales Ability, Potential In Selecting Sales Personel. If Provides An Objective Measure Of One Important Aspect Of Sales Aptitude, Namely Knowledge And Understanding Of Basic Principles Of Selling. This Test Is For 18 Years And Above. 20 Min To Complete. A) Test Booklets (Pfit. Of 25) B) Answer Sheet (Pkt. Of 100) C) Scoring Key D) Manual) , Machanical Aptitude Tests Battery (Matb) By Atmananda Sharma (Hindi/English):(Time 25 Min. Age 13 To 17 Years, Class Viii Io Xii. Test-L: Mechanical Knowledge Measures ‘Knowledge Of Tools Of Children. Non-Verbal And Culture Free. Directions And Examples.Test-Ii: Mechanical Comprehension Measure Factor ‘M’ Of Children. Non-Verbal And Culture Free. Test-Ill: Space Relations- Measures Factors ‘S’ Spatial Visualisation Of Children. Non Verbal And Culture-Free. Test-Iv: Form Relations-Measures Factor ‘P, Perceptual Ability And Inductive Reasoning Of Children. Test-V: Mechanical Adaptability-Measures Background In The Field Of Science, Scientific Applications And Related Activities Of Children) , Multi Factor Interest Questionnaire By Kapoor & Singh (English )(It Provide Scores On Eight Factors- Business, Clerical, Agricultural, Mechanical, Scientific, Outdoor Activities, Aesthesties And Social Meant For 11 To 18 Years.) , Vocational Interest Record By S.P. Kulshrestha (English)(The Present Record Contains 200 Vocations Belonging To Ten Different Vocational Interest Areas - 1. Literary, 2. Scientific, 3. Executive, 4. Commercial, S. Constructive, 6. Artistic, 7. Agriculture, 8.Persuasive, 9. Social, 10. Household. This Test Is Suitable For Delta And Higher Secondary Students, As Well As For The Students Of Colleges And Also For Soung Adults Out Of Schools And Colleges. (A}Test Booklets (A Pit. Of 100) (B)Manual , Educational Interestrecord By S.P. Kulshrestha (English):(The Present Record Contains 98 Edcational Subject/Activities Belonging To Seven Different Education Al Interest Areas. They Are -1. Agriculture, 2. Commerce, 3. Fine Arts, 4. Home Science, S. Humanities,6. Science, 7. Technology.(A)Test Booklets (A Pkt. Of 100) (B)Manuai , Student Teacher Value Inventory By Meenakshi Biswal (English)((A)Test Booklets (A Pkt. Of 100)(B)Manual) , Adjustment Inventory By Nilima Deka (English):((A)Test Booklets (A Pkt. Of 100} Manual) , Bells Adjustment Inventory By Huge M. Bell (English):((A)Tesl Booklets (A Pkl. Of 100) (B)Manual (C}Scoring Key) , Marital Adjustment Questionnaire By P. Kumar & Kanchana Rohtagi (English):(This Is Having 27 Items In Yes Or No Type Scale, And Reliability And Validity Indices Have Been Worked Out. Percentile Norms Are Given. Age Ranging From 28 To 45 Years. (Test Booklets (A Pkt. Of 100) (B)Manual) , Test Of Democratic Values By Alok Gardia (English):(A Reliable & Valid Test Of Democratic Values Which Contains 40 Multiple Choice Items. The Test Measures Six Democratic Values Namely Dignity Of Individual, Liberty, Equality’, Justice. Cooperation & Tolerance. It Can Be Administered On Upper Primary To Higher Secondary Students.The Test Is Also Suitable For Prospective Teachers (B.Ed. Students) And Teachers Of Different Schools. It Can Also Be Administered On Students Of Higher Education. (A)Test Booklets (A Pkt. Of 100) (B Manual) , Personal Adjustment Inventory For Creative Children By C.B. Asaha English):((A)Test Booklets (A Pkt. Of 100) (B)Manual) , A Test For Measuring Decision Making Capacity Of Educational Administrators By A.K.Pandey (English): ((A)Test Booklets (A Pkt. Of 100)(B)Manual) , Prosocial Behaviour Scale By Mahejabin& P.C. Shukla: (New)(This Tool Based On Likert Scale. The Scale Comprises 36 Items, On The Basis Of Six Dimensions. It Can Be Administered On The Secondary And Higher Secondary School Students. Split-Half Reliability Of The Testis 0.77 And Cronbach Alpha Is 0.794. This Test Measures The Level Of Prosociality, Which Indicates High Academic Achievement, Well Adjustment, Healthy Teacher-Taught Relationship And Social Harmony. Therefore, This Test Is Very Helpful To Develop Healthy Adjustment Skill, To Develop Healthy Reiationsbips& Social Harmony. This Tool Can Also Be Used As An Indicator Of Academic Achievement & Healthy Personality.A) Test Booklets (A Pkt. Of 100) B) Manual , Verbal Test Of Intelligence By M. Asthana And K.B. Verma (English):(This Test Covers Eight Areas Of General Mental Ability, Viz, Best Answer, Reasoning, Similar, Opposite, Analogy’, Mathematical Series, Mathematical Instruction And Classification.Norms Have Been Prepared Age-Wise. Age 13 To 21 Years. Time 20 Min No. Of Item100. (A)Resuable Test Booklets (A Pkt. Of 20) (B)Answer Sheets (A Pkt. Of 100) (C)Manual (D)Scoring Key(Stenciltype) , Group Test Of General Mental Ability By S. Jalota (English):(It Is A Point Scale Of General Ability For College-Educated Adults. (A)Resuable Test Booklets (A Pkt. Of 20) (B)Answer Sheet (A Pftt. Of 100)(C)Manual (D)Scoring Key) , The Southend Test Of Intelligence (English)((A)Test Booklets (A Pkt. Of 100) (B)Manual (C)Practice Sheets (A Pkt. Of 100) , On-Verbal Intelligence Test By Atmanand Sharma:(It Measures ‘G’ Of Children Age 11 To 16 Years, Grades Vi To X. Ii Is Culture-Free. Working Time 25 Min. (A)Tesl Booklets (A Pkt. Of 10) , Emotional Intelligence Test (For Adolescents) By Meena Jain & Madhu Jain:((A)Booklets (A Pkt. Of 100) (B)Manual) , Emotional Intelligence Test By Rakesh Pandey(Age Group 18 To 35 Years. The Scale Is Based On The Most Widely Used And Scientifically Validated Ability Model Of Emotional Intelligence Proposed By Mayer And Salovey. It Is A 51-Items Self Report Measure That Provides A Quick Assessment Of The Your Dimensions Of Emotional Intelligence, (A) Perception, Appraisal And Expression Of Emotion, (B) Emotional Facilitation Of Thinking, (C) Understanding And Analyzing Emotions, Employing Emotional Knowledge, (D) Reflective Regulation Of Emotion To Prompt Emotional And Intellectual Growth. The Scale Has Been Validated On A Wide Range Of Population And May Be Administered To Any Age Group Capable Of Comprehending Verbal Expressions. The Authors Have Tried This Scale On Adolescents And Adults Also And Found It Reliable And Valid. The Scale Can Be Used In Clinical Setting As Well As In The Area Of Health Psychology, Educational Psychology’ And Other Areas Of Psychological Investigations That Focus On The Role Of The Ability To Understand, Manage And Utilize Emotions For Personal Growth And Well Being. (A)Test Booklets (A Pkt. Of 100) (Bjmanual) , Emotional Intelligence Scale By Udham Singh &K.Ozha (English): (Age Group 15 To 30 Years. No. Of Item 46. Dimension Measure In This Test Are - Knowing And Managing Our Emotions, Motivatiting Our Self, Knowing Others Emotions, Handling Relationship With Others.A)Test Booklets Qa Pkt. Of 100) (B)Manual) , Social Intelligence Test By S.Mathur (English):(No. Of Item 50. Age Range 14 To 50 Years. A) Test Booklets (A Pkt. Of 100) B) Manual C)Scoring Key) , Culture Fair (Free) Intelligence Scale Indian Print By Kapoor, Rao & Singh/Cattell And Cattell (Indian Adaptation):(Minimise Cultural Bias. These May Be Administered Individually Or In A Group. They May Be Used To Identify Learning Problems Of Individuals And Assess Applicants Potential To Perform Job Relevant Tasks. (A)Scale I (English) (Cfis-I): For 4 To 8 Years And Older Retardates. Time - 25 Min. Norms Mental Age And L.Q. (B)Scaie Ii(English/Hindi) (Cfis-Ii E): For 8 To 14 Years And Average L.Q. Adults. Lt Contains Four Sub Tests Involving Different Perceptual Tasks.Completing Series,Classifying, Solving Matries And Evalua Ting Conditions.Time Taken 15 Min. (C) Scale Iii (English/Hindi) (Cfis-Iii E): For 14 Years And Above, I.E., Senior Secondary, College And High I.Q. Adults. By Employing Four Distinct Tasks, The Composite Intelligence Measure Avoids Reliance On A Single Skill. The Scale Is Recommended When Testing Better Educated Or More Intelligent Individuals, Because Of The Higher Difficulties Level Of Items And A Greater Refinement In The Higher Intelligence Ranges.) , Bhatia Battery Performance Test Of Lntelligence By C.M. Bhatia(Age Ii To 16 Years.) , Alexanders Pass Along Test:(Age L0+ Years Complete Set With Duco Painted Material And Design Cards Contained In A Wooden Or Plastic Box With Record Sheets (Pads Of 50) And Manual.) , Indian Adpatation Of Binet-Simon Scale((1960) By S.P. Kulshrestha) , Cube Construction Test:(Complete Set Witb Duco Painted Material And Models In Wooden Or Plastic Box Witb Record Sheets (Pad Of 50 Each With Manual) , Kohs Block Design Test:(Age 10* Years. Complete Set With Duco Painted Material And 17 Design Cards In Plastic Box With Record Sheets (Pads Of 50 Each) And Manual) , Manikin Test:(Six Pieces Representing Six Major Parts Of The Human Body To Be Fitted Together To Make A Conventionalized Figure Of A Man.) , Dearborn Form Board With Manual:(Contains The Form Board With 12 Designs Of Different Types. Two Wooden Blocks Used As Stimuli Are To Be Placed In Them. Measures Efficiency Skill.) , Pintner-Patterson Five Figures By Rudulf Pintner And Patterson:(With Manual. Contains Eleven Wooden Blocks And Five Figures. The Blocks Are To Be Fitted In Figures. May Be Used To Measure Quick Performance And Learning.) , Pintner-Patterson Short Scale Of Performance Test:(By Rudolf Pintner & Patterson: This Scale Comprises 10 Sub-Tests And Is Useful For Retesting Or Such Other Purposes. Complete With Materials For All 10 Sub-Tests.) , Hanfmann-Kasanin Concept Formation Test:(Consists Of 22 Properly Coloured Wooden Blocks. The Blocks Consist Of 5 Different Colours, 2 Different Heights And Sizes And Six Different Shades. Supplied Witb A Box.) , Reasoning Ability Test (Rat—D)(By L.N. Dube}’ (Englisb): This Test Consists 60 Items. For 12 To 17 Years Students Of Either Sex.) , Rais Concept Formation Test By G.C. Rai (College/Adult Form):(By L.N. Dube}’ (Englisb): This Test Consists 60 Items. For 12 To 17 Years Students Of Either Sex.) , Scientific Thinking Style Questionnaire By P.N. Singh & Ranjana Arora (Hindi/English}(No. Of Item 30. In The Preparation Of The Present Scale All The Six Components, Viz., Amoral, Creative, Developmental, Parsimonious, Testable And Unified Of The Nature Of Scientific Knowledge Have Been Used. Data Collection On The Graduate 1Evel.) , Interview Schedule For Measuring Achievement Oriented Child Rearing Practice By Manju Mehta (English)(: Four Items Related To Each Of The Following Orientation Were Prepared. Activistic-Passivistic-Orientation, Present-Future Orientation, Individualistic-Feministic Orientation. Various Achievement And Independence-Related Demands Were Found To Be Made At Different Age Levels Varying From 2 Years To 15 Years. The Question Used In Second Try Out In The Final Schedule, For Knowing Mothers Standard Of Age For Achievement And Independence Demands. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Pat Anxiety Scale (As- Ck5) By R.B. Cattbbbell, S.K.Krug&I.H.Scheier (English, Indian Print):(This 40 Item Questionnaire Provides A Convenient And Practical Measure Of Anxiety Level. It Is Constituted On The Basis Of 5 Principal 16 P.F. Factors Namely Emotional Instability, Suspiciousness, Guilt Proneness, Low Integration And Tension. It Is Meant For 16 Years And Adults. Approximate Time 15 Min. Standard Scores For Adult, College And High School Population.) , Guidance Need Inventory (Gni) By Sudha Kumari Sharma & Shahwar Fatima Zaidi (English) (No. Of Items 92. Dimensions-Educational, Vocational, Personal, Social, Emotional. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Mental Health Checklist By Pramod Kumar (Hindi/English):(This Check List Consists Of 11 Items. It Measures Mental Health Of Adult Age Range 18-28 Years. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Mental Depression Scale By L.N. Dubey (English):(No. Of Items Are 50. The Age Range 12 To 55 Years. (A)Tesl Booklets (A Pkt. Of 100) (B)Manual (E)Scoring Key) , Suicidal Behaviour Questionnaire By Sheweta Shandilya & Alok Gardia( English):(This Test Measures Four Areas Taps Into Lifetime Suicide Ideation And Or Suicide Attempt, The Frequency Of Suicidal Ideation Over The Past 12 Months, Taps Into The Threat Of Suicidal Attempt, Evaluatesself- Reported Likelihood Of Suicidal Behaviour In The Future. Age Group School And College Students. (A) Test Booklet (A Pit. Of 100)B Manual) , Case Study Test By L.N. Dubey (Hindi/English):((A)Test Booklets (A Pkt. Of 100)(B)Manual) , Medico Psychological Questionnaire By J. Bharat Raj (English)(This Questionnaire Consists Of 50 Items. It Measures Hysteria, Neurasthenia, Anxiety Neurosis, Reaction De Pression, And Obsessive- Compulsivetendency Of Normal And Abnormal Person. It Measures Neurotieism In Terms Of Emotional Adjustment And Emotional Maladjustment. It Is Standardized On College Student Of Both The Sex.) , Introversion-Extraversion Test By M.C. Joshi English):((A)Test Booklets (A Pkt. O£ 100) (B)Instruction And Score Cards (1Pair) , Kundu Introversion- Extroversion Test By R.N. Kundu (English):(A) Test Booklets (A Pkt. Of 100) B)Manual , Personal Efficacy Scale By A.P. Sing & Patiraj Kumari (1991, Hindi/English):(No. Of Items Are 19 For Adult. Norms And Relibaility Are Not Available) , Sex Differentiation Scale By A.P. Singh & Patiraj Kumari (1991, English):(No. Of Items Are 19 For Adult. Norms And Relibaility Are Not Available) , Family I Nvolveoient Inventory By A.P. Singh & Pramila Tiwari (2003, English): (No.Of Items Are 24. Norms Are Not Avalible. For Adults.) , Life Satisfaction Scale Bv A.P. Singh & Pramila Tiwari(2003,Engiish):(No Of Items Are12.Foradults.) , 16 P.F. Test S.D. Kapoor (Hindi/English): Indian Adaplation:(It Has 16 Primary Scales And Other Numerous Derivative Scales. A Test Of Normal Adult Personality The 16 P. F, Form A To E Effectively Measure Levels Of (I) Warmth, (Ii) Intelligence, (Iii) Emotional Maturity, (Iv) Dominance, (V) Impulsivity, (*I) Super Ego Strength, (Vii) Boldness, (Viii) Sensitivity, (Ix) Trust, (X) Imagination, (Xi) Shrewdness, (Xii) Confidence, (Xiii) Radica Alism, (Xiv) Self-Sufficiency, (Xv) Self-Sentiment And (Xvi) Tension. Additional Derived Scales Include Five Second Order Factors— Extraversion, Anxiety, Tough Poise, Independent And Social Control Plus Composite Score For Creativity, Adjustment, Leadership And Numerous Other Criteria Related Scales. Lt Is Widely Used In Industry’And Business For Selection, Placement, Training And Promotion Of Personnel. Lt Also Facilitates Accurate Diagnosis And Effective Treatment. Range 16 Years And Above. Forms A And B Are Equiva Lent Forms Of 187 Items, Untimed, Requires 45-60 Min, Forms C And D Are Equivalent Forms Of 105 Items, Meant For 15+ And Adult, Untiined, Requires 25-30 Min Land Form E Of 128 Items, Is For Low Literates. Manual Also Includes Norms Table. Form A/B/C/D/E (Any One) , Childrens Personality Questionnaire By Porter And Cattell (Cpq-Pc) (English, Indian Print):((The Cpq Measures 14 Primary Traits Useful In Understanding And Evaluating The Course Of Personal, Social And Academic Development, Plus Traits Related To Creativity. Traits Measured By Cpq Include Emotional Stability, Self-Concept Level, Excitability And Apprehension, Scores For Extraversion, Anxietyety And Other Broad Trait Patterns Are Also Obtained As Combination Of The Primary Scales. It Is Meant For Age Groups Between 8-12 Years. Each Form Has 140 Items. Time Required Is 30 To 60 Min Per Form. Minimum Reading Level Is 4Th Standard) , High School Peronality Questionnaire By S.D. Kapoor (English):(Form-A Or B. Jr-Sr. Hspq Measures14 Primary Personality Dimensions -(I) Warmth, (Ii) I Ntelligence, (Iii) Emotional Maturity, (Iv) Excitabilty, (V) Assertiveness, (Vi) Enthusiastic,(Vii) Su Per Ego Strength, (Viii) Venturesome, (Ix) Dependent, (X) Individualistic (Xi) Depressive, (Zii) Self Sufficient, (Xiii) Controlled, (Xiv) Tense. It Contains T42 Iteras Ia Each Form And Is Meant For Age 12-18 Years. Time Required Is 40 Min. (A)Test Booklets (A Pkt. Of 20) (B)Test Profile (A Pkt. Of 100) (C)Manual (D)Answer Sheets (A Pkl. Of 100) (E)Scoring Key) , Adolescent Problems Scale By H.D. Badami (English}(: The Present Problem Inventory Is College Level And Post-Graduate Level. No. Of Items 265. In This Test 9 Areas Measuring- 1. Physical Health And Fitness, 2. Self And Self-Image, 3.Economic And Mate Rial Facilities, 4. Friendship, Sex And Marriage, 5.Family, 6. Social, 7. Educational, 8. Vocational, 9. Custom, Morality & Religion. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Sex-Role Inventory By Madhu Asthana And O.P. Chaudhary (Hindi/English (No. Of Items Are 60. (A)Manual (B)Test Booklets (A Pkt. Of 100) (C)Scoring Key) , Eysenck Personality Inventory By H.J. Eysenck And Sybil B.G. Eysenck (English} (: (A)Test Booklets (A Pkt. Of 100)(B)Manual) , Eysenck Personality Inventory (Epi) By G.P. Thakur (English):(No. Of Items Are 57. (A)Test Booklets (A Pki. Of 100) (B)Manual (C)Scoring Key) , Temperament Scale (For Chidlren) By J.D. Murjani (Hindi/English):)(For Age Group 8 14 Years. No. Of Items 30. Ten Dimensions Are Measuring Sociability, Tolerance, Aggressiveness, Warmth,Responsibility, Impulsivity, Cheerfulness, Vigorous, Co- Operativeness, Persistence. (A)Test Booklets (A Pit. Of 100) (B)Manual) , The Inferiority Questionnaire By G.C. Pati (English)(It Is A 20 Item Test.Validity Coefficient Against ’Self-Rating’ Is 0.717 And Reliability (Test-Retest) Is 0.920. Scheme For Qualitative Interpretation Of Scores Provided. (A)Test Sheets (A Pkt. Of 100) (B}Manual) , Coping Strategies Test (2001) By A.K. Srivastava (Hindi/English):(Age Group 11 To 18 Years. No. Of Item Are 50. Five Major Categories Measure - Behavioural-Approach, Cognitive-Apprroach, Cognitive- Behavioural Approach, Behavioural- Avoidance,Cognitive Avoidance. (A)Test Booklets (A Pkt. Of 100)(B)Manuai) , Aggression Questionnaire By G.C. Pati (Hindi/English):(It Is Composed Of 16 Multiple Alternative Type Of Answer. Its Ratio Is 0.71 And Validity Against External Criterion Is 0.828. Scheme For Qualitative Interpretali On Of Scores Is Provided. The Questionnaire Consists Of 16 Questions. (A)Test Booklets (A Pkt. Of 100} (B)Manual) , The Dependence Proneness Scale By Jai B.P. Sinha (Hindi/Englisb):(There Are Four Areas - Affection- Affiliation, Lack Of Internal Control, Evading Responsibility And Conformity; To Be Rated On A 5 Point Likert Scale. Its Reliability Coefficient Is .94. Individual Administration Is Advised. Validity Has Been Established Against Many Experimental Situations. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Self-Esteem Questionnaire By Minakshi Biswal (English)(No. Of Items 50. Age Group 15-25 Years. It Can Be Used For Any Behavioural Research Concerning Self Esteem, Survey Purpose/For Comparison Of Population. It Gives A Quick Measure Of Self-Esteem For Experimental Purposes. It Is Suitable For Group Administration As Well As For Individual Testing. The Test Is Developed And Standardized On An Indian Sample. (A) Test Booklets (A Pkl. Of 100 B) Manual) (1 Pair) (D)Manual) , The Self-Confidence (S-C) Scale By M. Basavanna (English):(It Is A 100 Item Scale In T & F Type. It Is Designed To Estimate The Level Of Self-Confidence Among Adolescents And Adults. Corrected Split-Half Reliability Is 0.94. Validity In The Form Of Item Validity And Against Other Experimental Indices Is Established. The Test Booktlet Is Reusable. (A)Test Booklets (A Pkt. Of 20) (B)Answer Sheets (A Pkt. Of 100) (C)Scoring Key (1 Pair) (D)Manual) , Self-Esteem For Children By Anand Kumar (English):(A Set For Children Contains 50 Items And The Following 4 Subscales: 1.General Self-Esteem, 2. Social Self- Esteem, 3. Academic Self-Esteem, 4. Parental Self-Es Teem. Age Group 8 To 15 Years. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Self-Concept Inventory (Adults) By Beena Shah (English):(No. Of Items Are 64. Age Group 21 To 50 Years. 10 Dimensions Measured In This Test Are - 1. Social Self Concept, 2. Emotional Self-Concept, 3. Physical Self-Concept, 4. Cognitive Self-Concept, 5. Aesthetic Self-Concept, 6.Political Self-Concept, 7. Job Related Self-Concept, 8. Self-Coafideoce, 9. Beliefs And Traditions, 10. Personality Traits. (A)Test Booklets (A Pkt. Of 100) (B)Manual) , Personality Assessment Ranking Method By N.K.Jain (English)((A}Ranking Sheets (A Pkt. Of 100)(B)Manuai) , Multi-Dimensional Assessment Of Personality Scale (Map Series) By Sanjay Vohra:(Map Is A Series Of Tests Ranging From Children Of Primary Level To Normal Adult Personality. Lt Is Used To Analyze/Report Individual Differences In Personality. The Map Series Has Four Forms For Different Levels (Map Form A, T, C And P) , Sentence Completion Test By L.N. Dubey & Archana Dubey (English):(This Test Consists Of 50 Items. It Maeasures Certain Personality Traits — Sociability, Self Confidence And Ambitions. All The Sentences Are So Framed That They Lead To Reveal The Positive Or Negative Aspects Related To Ones Trait. Age Range 14 To 19 Years. (A)Test Booklets (A Pkt. Of 100)(B)Manual0 , Draw-A-Man Test By Pramila Pathak (Age 2.5 To 16 Years.( , Thematic Apperception Test With Manual By H.A. Murray (Original)(Age 14+ Years): , Indian Adpatation Of Children Apperception Test With Manual:((Cat) By Uma Choudhary. Age 4 To 10 Year.) , Indian Adpatation Of Thematic Apperception Test With Manual (Tat) By Uma Choudhary(: Age 15+ No. Of Cards 14 With One Blank:) , Children Apperception Test By Bellack & Bellack (Original) (Cat):(The Cat Consists Of Ten Pictures Depicting Animals In Various Situations. It Is Used With Children Of Both The Sexes Primarily Between The Ages Of 3 To 10 For Maximal Usefulness. It Is Designed To Facilitate Understanding Of A Childs Relationship To His Most Important Figures And Drives. A) Animal Figure B) Human Figure C) Supplementary) , Rorschach Inkblot Test:(With Psychodiagnostic Plates, Record Blank, Location Chart And Manual By Herman Rorschach.) , Indian Adpatation Of Rosenzweig Picture Frustraction Test (Children) By Udai Pareek:(English)(: For Age Group 4 To 13. (A)Test Booklets (A Pkt. Of 20) (B)Record Sheets (A Pkt. Of 50) (C)Manual) , Peer Pressure Scale By Kusum Tyagi & Nidhi Gupta (English)(: Age Group 12 19 Year. No. Of Items 50. This Test Measures 5 Areas - 1. Interpersonal Relationsbip, 2. Agreeableness, 3. Economic Pressure,4. Academic/Scholastic And 5. Consientioun Sess. (A)Test Booklets (A Pitt. Of 100) (B)Manual) , Tweezer Type Dexterity Test:(Teak Wood Base With Rust Proof Metal Square Top Witb 100 Holes. 100 Needles Provided With A Fine Tweezer.) , Manual Dexterity Test:(Plywood Made With Sockets And 60 Pegs. Painted Or Polished And Fine Finish.) , Finger Dexterity Test :(Box Type.) , Threading Test:(The Device Is Employed In Testing The Speed And Dexterity In Finger Movement. The Time Required To Pass A Thread Through An Eye’ Of 33 Rods, Three In A Row And 11 Rows, Is Measured. The Quality Of Performance Can Also Be Checked Easily.) , Complete Minnesota Dexterity Test:(This Test Measures Simple Hand-Eye Coordination And Gross Motor Skills. It Consists Of A Battery Of Five Tests: Placing, Turning, Displacing, One- Hand Turning And Placing, And Two- Hand Turning And Placing. This Test Comes Complete With Two Folding Pegboards, 60 Blocks.) , Whipples Tapping Board: (This Apparatus Demonstrates One Of The Most Elementary Psychomotor Skills. The Task Is Simply To Tap The Stainless Steel Plates As Rapidly As Possible. Designed For Versatility And Durability, This Unit May Be Used To Demonstrate A Number Of Important Principles) , Hand Coordination Test (Electrically Operated):(Used For Teaming Experiments Of Two Hand Coordination, Consists Of Mechanical Device Permitting Horizontal And Vertical Movements Of A Pin Or A Pencil Through Slot Ted Design. Time And Errors Are Counted. Using Impulse Counter Cumulative Record Of Errors Can Be Assessed. 389. Minnesota Rate Of Placin) , Eye Hand Co-Ordination Test (Drever & Collins Model):(A Semi-Circular Hand Plywood Is Covered On One Side By An Iron Sheet. A Scale Is Mounted On Which The Rider Is Moved On Both The Sides Except The Blind Zones. The Subject Sits With His Chin Resting On Chin Stand. Fine Finish With Pointer And The Rider.) , Speed And Accuracy Test (English):((A)Numerical Sheets (A Pad Of 100)(B)Alphabetical Sheets (A Pad Of 100) (E)Manual) , Social Maturity Scale By J. Bharatraj (English):(For Age Level From 0 To 15 Years. A) Test Booklets (A Pkt. Of 100) B)Manual) , Social Cognition By N.K.Jain (English):((A)Stimulus Material (A Pkt. Of 100)(B)Scoring Template (A Pkt. Of 100) (C)Manual) , Environmental Awareness Questionnaire By Sunita Singh (Hindi/English)(:For Secondary Level To P.G. Level. The Questionnaire Contains 32 Items From Different Areas Related To Measuring Of Environment, Case And Effect Of Pollution And Prevention. It Has High Reliability (0.87). The Validity Has Been Ensured Through Experts Opinion. Percentage Score Norms Have Been Provided. (A) Test Booklets , Inter Personal Attraction By Ripunjay Deo Singh & Vikas Kumar (Hindi/English):(No. Of Items Are 34. Dimension/Factors Are 1. Interactional Factors, 2. Personal Factors, 3. Personality Factors, 4. Physical Factors, 5. Situdational) , Rumour Analysis By N.K.Jain (English)((A)Stimuius Material (A Pkt. Of 100) (B)Scoring Template (A Pkt. Of 100) (C)Manual) , Sociometric Choice Test By Meera Joshi & Jagdish Pandey (English):(This Test Records Interpersonal Attractions Among The Members Of A Group. The Test Should Be Used With A Group Of Persons Who Have Been Together Long Enough To Be Acquainted With One Aaother, Such As In A Class, In A Factory, Club, Etc. Each Individual Is Asked To Choose Five Group Members With Whom He Would Like Most And Also Dislike Most To Study, Play, Sit Or Work, Lunch And Walk. The Names Are To Be Written According To Their Choice Positions. The Choices May Be Interpreted Either In Manner Of A Sociogram Or On The Basis Of Ratings On The Preference Scale Continuum. (A)Test Booklets (A Pkt. Of 100) , Impression Formation By Photographs By Meera Joshi & J. Pandey (Hindi/English):((A)Cards (B)Answer Sheets (A Pkt. Of 100) (C)Manuai) , Aids Awareness Questionnaire By Madhu Asthana (Hindi/English):Lthy Personality. A) Test Booklets (A Pkt. Of 100) B) Manual((A)Manual (B)Test Booklets (A Pkt. Of 100)) , Indian Adaptation Of Hutts Bender Gestalt Test For Adults By C.B. Dwivedi &Subhara Banerjee:(This Adaptation Provides Scoring Instructions For 17 Pathological And For The Adienceabience Scale. It Is Highly Useful For A Quick Understanding And Screening Of Psychopathological Cases. Normative Data Have Been Provided For The Mentioned 17 Pathological And Adolescent-Abience Scale Separately. (A)Manual (B)Test Cards (Per Set) (E)Lndividuai Response Sheet (A Piit. Of 100) (D)Test Booklets (A Pkt. Of 100) , Occupational Role Stress Inventory By Udai Pareek (English):((A)Test Booklets (A Pitt. Of 100)(B)Manuai) , Job Anxiety Scale By M.M. Sinha And A.K. Srivastava (English):(The Scale Comprises 80 Items Which Reveals Employees Anxiety Being Manifested In The Context Of Following Seven Components Of The Job (1) Security- Job Security And Safety, (2) Recognition, (3) Human Relations At Work, (4) Reward And Punishment, (5) Self-Esteem, State Punishment, (6) Self-Esteem, Self-Image, (7) Future Prospects, (8) Capacity To Work. The Scale May Be Administered To The Employees Operating In Production As Well As Non Production Organisations. The Scale May Be Conveniently Used For Research, Survey And Diagnostic Purposes. Split-Half Reliability Is 0.92, And Test-Retest Reliability Is 0.94. The Test Was Validated Against Sinha Anxiety Scale (R-0.54), Sarasons General Anaiety Scale (R-0.56), Taylors Manifest Anxiety Scale (R 0.48). (A)Test Booklets (A Pkt. Of 100) (B)Manual ) , Creative Behaviour Questionnaire By A.P. Singh & L.K. Mishra (2009, English)(No. Of Items Are 13 For Manager) , Intrinsic Work Motivation Questionnaire By A.P. Sngh& L.K. Mishra (2009, English):(No. Of Items Are 12. For Employee.) , Audio Visual Aids Chart Types Of Modern Indian Education . Models Of Teaching History And Development Of Indian Education School Of Psychology Theories Of Personality Theories Of Intelligence Theories Of Learning Major Schools Of Philosophy Schools Of Indian Philosophy Physiological Charts: A Set Of 7 - Eve, Ear, Brain, Skeleton, Nervous System, Human Body, Blood Circulation) , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) David Weehsler , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) H.I Eysenck, , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Kuri Lewin , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Alfred Binet , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Wilhelm Wundt , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Gordon Allpor , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) B.F. Skinner , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Sigmund Freud , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Edward L.Throndihe , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Ivan P. Paxlov , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Jean Piaget, , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Wolfiang Kohler , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Edwin Guthrie , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Carl Gustav’ Jung , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Raymond Bernard Catteii , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) John B. Watson , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Herman Rorschach , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Carl Rogers , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Hermann Ebbinghaus , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Abraham Maslow , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Aristotle , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Erin H. Erikson , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Rollo May , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Albert Bandura , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Lewis Terman , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Henry Murray , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Roberi Pluichik , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Alfred Adler , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Hefimann Von Helinholtze , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) William James , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) John Dewey , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Herbert Spencer , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) John Friedrich Herbart , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Jean Jacques Rousseau , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Johann Heinrich Pestolozzi , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Friedrich Frobel , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Max Wertheimer , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Rene Descartes , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Plato , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Socrates , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Maria Montessori , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) B.Russell , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Francis Galton , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) William Mcdougall , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Edward C. Tolman , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Louis Leon Thurstone , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) William Heard Kilpatrick , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Gastav Theodor Fechner , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Ernst H. Weber , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Charles Robert Darwin , Photographs Of Eminent Foreign Psychologists/Educationists (Coloured Size 11 X 17) Jerome Seymour Bruner , Blind Goggles , Metronome:With Bell (Imported)

BRR : 7636241 Tender For Provision Of Cgsd (Kochi) At Willingdon Island, Kochi; 1 SCHEDULE A Part - I (BUILDING & STRUCTURE WORKS)Details of prepriced schedule is given in tender documents. 2 SCHEDULE A PART-II ( SITE CLEARENCE/DEVELOPMENT & EARTH WORKS) Details of prepriced Schedule is given in tender documents. 3 SCHEDULE A PART-III (INTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents. 4 SCHEDULE A PART-IV (INTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents. 5 SCHEDULE A PART-V (FIRE FIGHTING)Details of prepriced Schedule is given in tender documents. 6 SCHEDULE A PART-VI (ROAD/PATH/ HARD STANDING/CULVERT)Details of prepriced Schedule is given in tender documents. 7 SCHEDULE A PART-VII (EXTERNAL WATER SUPPLY) Details of prepriced Schedule is given in tender documents. 8 SCHEDULE A PART-VIII (EXTERNAL ELECTRIFICATION) Details of prepriced Schedule is given in tender documents. 9 SCHEDULE A PART-IX (SEWAGE DISPOSAL) Details of prepriced Schedule is given in tender documents. 10 SCHEDULE A PART-X (AREA DRAINAGE) Details of prepriced Schedule is given in tender documents. 11 SCHEDULE A PART-XI (COMPOUND WALL) Details of prepriced Schedule is given in tender documents. 12 SCHEDULE A PART-XII (ORGANIC WASTE CONVERTER AND SMART ENERGY METER) Details of prepriced Schedule is given in tender documents. 13 SCHEDULE A PART -XIII (MISCELLANIOUS ITEMS) Note:- This schedule is not pre-priced by MES and the pre-priced rate indicated as Rs 0.00 under Col. E signifies this fact only. 14 INTERNAL WATER SUPPLY S & F for 15 mm dia bore CP two way bib cock with CP wall flange (Make : Jaquar Model No. OPP15041PM / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 15 S & F for 15 mm dia bore CP bib cock with CP wall flange (Make : Jaquar Model No. OPP15037PM / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch, screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 16 S & F for 20 mm bore concealed Stop cock reqular brass body with spindle extnwith Exposed Part Kit of Concealed Stop Cock with Fitting Sleeve, Operating Lever & Adjustable Wall Flange (Compatible with ALD-083CQT & ALD-089CQT)(Make : Jaquar Model No. ALD 089 CQT/ Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch , screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 17 S & F for 25 mm dia bore concealed Stop cock reqular brass body with spindle extn with Flush Cock & Wall Flange 25mm Ceramic Disc Cartridge) with Plain Knob (Make : Jaquar Model No. ALD 081/ Eqvlt in Kohler/Grohe), cast copper alloy, screwed down high pressure with crutch, screwed both ends for CPVC pipes or for union and fixed complete all as specified and directed by Engr-in-charge. 18 S & F 20mm bore CP angular stop cock with CP wall flange (Make : Jaquar Model No. CQT 23053 / Eqvlt in Kohler/Grohe), cast copper alloy, screwed down, high pressure with crutch, screwed both ends for iron pipe or for union and fixed 19 S & F for 100 mm overhead shower rose round shape single flow (ABS Body chrome plated with gray face plate (Make : Jaquar Model No. 1989 with SHA 479L300S / Eqvlt in Kohler/ ESS ESS) with Shower Arm ø20mm & 300mm Long Round Shape with 90˚ Bend for Wall Mounted Showers with Stainless Steel connected to pipe complete all as specified and directed by Engr-in-charge. 20 COOLING APPLIANCESDesign, Supply, Installation, Testing and Commissioning of Invertor Type Floor Mounted Packaged AC Units of specified capacities, combination of energy efficient Inverter compressor plus fixed compressors, nominal capacity condensing unit with all standard fittings, safety devices, like HP/LP cutout, single phase preventor, overload relays, R-410A Gas, vibration isolation pads etc. Suitable to work till 50 Deg ambient, Blue Fin Condensor and Corrosion Resistant Body, Wide Voltage Range 360V - 440V, The quoted rate shall include Group controller also asrequired for controlling AC from a single point and timer option for load sharing of AC units complete all as specified and as directed by Engineer - in - charge, of following capacities.Note: Design report shall be submitted before execution of work at site by the contractor to GE for his scruitiny/comments and further submitted to AO for his approval.Make: Blue Star/Daikin/Haeir/Godrej/Voltas/Equivalent. (HIGH SIDE (MACHINES))(Outdoor unit) 21 a) 22 TR Inverter Package AC Units 22 b) 16.5 TR Inverter Package AC Unit 23 Design, Supply, Installation, Testing and Commissioning of Normal Type Floor Mounted Packaged AC Units of specified capacities, nominal capacity condensing unit with all standard fittings, safety devices, like HP/LP cutout, single phase preventor, overload relays, R-410A Gas, vibration isolation pads etc. Suitable to work till 50 Deg ambient, Blue Fin Condensor and Corrosion Resistant Body, Wide Voltage Range 360V - 440V, The quoted rate shall include support works for outdoor units with necessary catwalk for service access complete all as specified and as directed by Engineer - in - charge, of following capacitiesNote: Design report shall be submitted before execution of work at site by the contractor to GE for his scruitiny/comments and further submitted to AO for his approval.Make: Blue Star/Daikin/Haeir/Godrej/Voltas/Equivalent. LOW SIDE (MACHINES))(Indoor unit) 24 a) 22 TR Inverter Package AC Units 25 b) 16.5 TR Inverter Package AC Unit 26 Supply, Installation and Testing of Refrigerant pipingwith necessary clamping (suction & Discharge) Hard/Soft drawn Copper tube of suitable sizes, with copper elbows, tees, Tubular Nitrile Insulations etc as required complete all as specified and as directed by Engineer - in - charge. 27 S & F Control Cabling B/W Indoor & Outdoor units 28 M & L Refrigerant Gas - R410A 29 Supply, Installation and Testing of Hard PVC drain piping. Drain piping with Tubular Nitrile Rubber Insulation: complete in all respects, well clamped till drain Points complete all as specified and as directed by Engineer - in - charge. For All Units 30 DUCTINGSupply, fabrication, installation, testing of GI rectangular ducts, complete with all fittings such as tee, bends, special off shoots, inspection doors, transformation pieces etc. as required as per IS 655 including suspension and supporting arrangement for plenum, duct etc. required complete all as specified and as directed by Engineer - in - charge. 31 a) Using 0.63 mm (24 Gauge) GI sheet 32 b) Using 0.80 mm (22 Gauge) GI sheet 33 c) Using 1.00 mm (20 Gauge) GI sheet 34 DUCT INSULATION & LININGSupply and Installation of Acoustic Insulation of ducts using 9MM Open Cell Nitrile Rubber, well adhesived, 150 - 180 Kg/cm2 complete all as specified and as directed by Engineer - in - charge. 35 Supply, installation & testing of Thermal Insulation of ducts using 9MM Closed Cell Nitrile Rubber, well adhesived, 40-60 Kg/cm2 complete all as specified and as directed by Engineer - in - charge. 36 S & F Canvas Connection 37 AIR DISTRIBUTION PRODUCTSSupply and Fixing of Powder Coated Aluminium Grills/ Diffusers (Supply/ Return) complete all as specified and as directed by Engineer - in - charge. 38 S & F Collar Dampers 39 Supply and Installation of Fire Dampers complete all as specified and as directed by Engineer - in - charge. 40 Supply, Installation, Testing and Commissioning of Heater Bank Plus Humidistat Arrangement complete all as specified and as directed by Engineer - in - charge. 41 Supply and fixing, testing and commissioning water coolerhaving stainless steel body with inbuild purifier HIMA 7 NHC, dispencing capacity 125 ltr/hr and storage tank capacity 40 ltr normal and 40 cold electric driven (single phase), 230 volt, AC power supply with all connecting accessories complete all as specified and directed. 42 Supply and fixrefrigerator, electric driven (single phase), 220 V,50 HZ, capacity 195 Litres, 3 Star rated direct cool inverter, single door all as specified and directed by the Engineer-in-Charge. 43 Supply and install, testing and commissioning of split type air conditioner 1.5 TR Capacity of invertertechnology 5 star rating with cordless remote control single phase 240 volts complete with all accessories such as indoor and outdoor units and refrigerent tubing of adequete length as required at site indoor mounting plate, duly powder coated fixing with anchor bolts at any height, drain pipe of suitable size brought to ground level from any height, initial filling of refrigerent gas including making round hole on existing wall for taking up refrigerent tubing, drain pipe, cables, etc and making good the disturbed surface by matching with existing adjoining surface complete all as specified and directed (Cooling appliances- qty 4, Air conditioning- qty 10) 44 Supply and fix Voltage stabilizer 3 KVA for automatic operation, single phase naturally air cooled indoor type, wall mounted & designed for input variation between 170 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% 45 Supply and fix Voltage stabilizer 4 KVA for automatic operation, single phase naturally air cooled indoor type, wall mounted & designed for input variation between 170 V to 280 V with output voltage stabilized at 230 V with accuracy of ± 2.5% (Cooling appliances-qty4, Air conditioning- qty 10) 46 AIR CONDITIONINGSupply and install,Testing & commissioning of split type air conditioner 2 TR capacity of inverter technology 5 star ratingwith cordless remote control, single phase 240 volts complete with all accessories such asindoor and outdoor units and refrigerent tubing of adequete length as required at site, indoor mounting plate, duly powder coated fixing with anchor bolts at any height, drain pipe of suitable size brought to ground level from any height, initial filling of refrigerent gas including making round hole on existing wall for taking up refrigerent tubing, drain pipe, cables etc and making good the surace by matching with adjoining surface complete all as specified and directed. 47 Supply and fix Voltage stabilizer 5 KVA for automatic operation,single phase naturally air cooled indoor type, Wall mounted type & designed for input variation between 170 V to 280 V with output voltage stabilized at230 V with accuracy of ± 2.5% 48 INTERNAL ELECTRIFICATIONS & F LED Mirror light 1 x 5W LUMOS ECCO 1 feet Make: Luker or Equivalent 49 S & F modular MCB DBOx 3 Pin Socket with MCB SP 20 Amp, 240 V including plastic enclosure as per manufacturer instruction fixed on wall surface complete for Air conditioner all as specified and as directed. (Make:-Havells, Model-DHDMCSN0251016 or equivalent) 50 Supply and fix Air circulator of 600 mm sweep AC single Phase. 230V, 1440 RPM complete all as specified and as directed. (Make: Havells model, Turbo Force Wall or equivalent) 51 S & FVertical triple pole & neutral (VTPN), double door, 16-way metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for FPMCCB as incomer and TPN/SP MCBs as outgoing, reversible metal door, 200 A copper busbar for each phase, fully insulated & shrouded neutral bar, earth bar, wiriest & cable ties for cable management, profited masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and directed. 52 S & FVertical triple pole & neutral (VTPN), double door, 4-way metallic modular distribution board conforming to IEC 61439-3, suitable for flush / surface mounting with provision for FPMCCB as incomer and TPN/SP MCBs as outgoing, reversible metal door, 200 A copper busbar for each phase, fully insulated & shrouded neutral bar, earth bar, wiriest & cable ties for cable management, profited masking sheet, etc. having IK 09 & IP 43 protection complete all as specified and directed. 53 M & L for Flame ProofMCB Distribution board SPN 12 way, with case iron body, powder painted, with 200 Amps rated bus bar etc. including provision of one 32 Amps SPN MCB as incoming and 6 Amps SP MCB -10 Nos as outgoingcomplete all as specified and as directed. 54 M & L for Flame ProofMCB Distribution board SPN 8 way, with case iron body, powder painted, with 200 Amps rated bus bar etc. including provision of one 32 Amps SPN MCB as incoming and 6 Amps SP MCB- 6 Nos as outgoingcomplete all as specified and as directed. 55 Supply and fix Engage light with Green & Red LED complete all as specified and as directed 56 Supply and fix of CS mounted high intensity LED search light, long range, manually swivel in all direction, 250 W, minimum range 700 meters, Single, LED Efficiency> 140 lm/w, PF> 0.95, CCT 5500K - 6500K, Optical grade PMMA/PC lens/reflector efficiency>95%, multiple circuit to avoid complete run down, anti UV, narrow beam 5 degree, die cast LM6 body with air fins, powder coated, constant current, an average lux at 10 meter - 8000 lux with circle of approx 600 mm, working temp: -20 to +60 degree C, input Volt 100-300 VAC, 50 Hz, PF >0.95, IP-66, confirming to LM79/ LM80 and type tested as per IS: 10322/ IS: 13383, BIS approved and Govt lab tested for lux intensity. The search light is completed with manual revolving CS stand D20cm x H15cm (min.) with 3 nos. foundation holes for mounting of searchlight on watchtower structure, manual rotation of light on horizontally 360 degree with 45 degree tiltable with provision of both instant locking arrangement at desired position. Model No. CS-LRFLL-25PC25 of KALIN make or equivalent 57 Supply, install, testing and commisisong of outdoor floor/wall mounted thermoplastic polycarbonatefeeder pillar panel, Enystar EmptyEnclosures, IP-65, weatherproof, corrosion free, Halogen and Silicon Free, Frame retardant with Opaque Lid Size-[276 x 546 x 186]mm and Transparent Hinged Lid, completed all as specified and directed. 58 M & L for TV socket module metal flushed including flushed Box cover plate Box for 2 way module complete all as specified. 59 M & L for telephone jack with module metal flushed including flushed Box cover plate Box for 2 way module complete all as specified. 60 Supply and lay coaxial cable for TV Cabledrawn through conduit 61 S & F flame proof exhaust fan 300 mm sweep, single phase, 1440 RPM complete all as specified and as directed. 62 FIRE FIGHTINGSupply and fix Foot Valve conforming to IS 4038, 100 mmdia. 63 Supply and fix Foot Valve conforming to IS 4038, 150 mmdia. 64 Supply and fix Cast Iron Air Valves with single air Outlets, conforming to IS 14845 of size 100 mm dia bore and fixing up in Cast Iron Water supply mains of size 100 mm dia. 65 S & F sprinkler flexible drop pipe 1 mtr long. 66 S & F sprinkler rossette 25 mm dia. 67 Supply and installation, testing and commissioning of Analog Addressable type Active Loop Repeater (Loop power/external power) Fire terminal with inbuit turbo isolator, Backlit LCD Display 6x40 characters display, having Controls For Reset, Mute, Accept, Silence alarms and Self Test, with programmable free keys and Duly Approved byEN54/LPCB/VDS/FM Make: SIEMENS/NOTIFIER/BOSCH 68 M & L for Low smoke Zero helogen flame retardent fire alarm cable2 core, 1.5 mm² copper conductor confirming to BS7629-I, BS6387 & rated for 500 v grade having plaine sraded copper coductutor with priming insulation of glass mica fire resistance tape & secondery insulation of high performancesilicon rubber with electrostatic screen of aluminium fire barrier Type LT53 outer sheath confirming to BS 7655, red in colour drawn through & including concealed steel conduit including laying,fixing,connecting complete all as specified and directed. 69 Staircase signage down of make bajaj cat part no. 111499 model no. DSDWBB 3W double side display for staircase downwards (with 2 hours built in battery backup) complete all as specified and directed at site complete all as specified and directed. 70 S & F wall mounted LED emergency Exit signage luminaire Lit up using regular mains supply comes with a unique rechargeable Ni-Cd battery capable of emergency back up upto 05 hours(Cat No. 220211 Make Bajaj or equivalent to CG/Havells. 71 Supply, Installation, test and Commissioning CPRI APPROVED factoryfabricated, indoor type, LT panel board , made out of 2 mm thick CRCA Sheetsingle door withboth side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeddedwith 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete withinternal connection with suitable size of cable, cable lugs and cable glandsPCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation includingcomplete all as specified and comprising of the following:- Make of MCCB/MCB -MDS/LEGRAND/L&T/HEGGER (Main Fire Fighting Panel)INCOMING(i) MCCB 4 Pole 160 amp 50 Hz, 415 V with reputing capacity 35 KA with microprocessor based release - 01 No.(ii) Voltmeter Digital type 0-500 Volts range flush type with selector switch- 01 No(iii) Aluminium Bus bar TPN - 200 amps- 1setOUTGOING(i) MCCB 3 Pole 125 amp 50 Hz, 415 V with reputing capacity 35 KA with microprocessor based release- 01 No.(iii) MCB TPN 32 Amp -02 Nos(iv) 80 HP S/D STARTER- 01 Nos(v) DOL STARTER 7.5 HP- 01 Nos(vi) Motor Protection Relay32-88 amps- 1 no. (vii) Motor Protection Relay2-5.5 amps- 1 no. (viii) On/Off/Trip Indication Lamps, 220 V AC- 6 nos.(ix) Start/Stop Push Button, 2 No. (x) Phase indicating lamps RYB for incoming and each outgoing connection.(xi) Digital type Ammeter 0- 150 amps with selector switch and CT coils of suitable capacity for incoming and each outgoing connection- 1 no. 72 M & L for coating and wrapping of under ground steel pipe buried in soil shall have protection against corrosion as per IS-10221.The coating and wrapping shall be carried out in systamatic manner to get uniform thickness of coating as per IS specification 73 Supply, Installation, test and Commissioning CPRI APPROVED factoryfabricated, Indoor type, LT panel board, made out of 2 mm thick CRCA Sheetsingle door withboth side opening including Neoprene Rubber Gasket, suitable for 440 Volt 3 Phase 4 Wire System, including Danger Plate, Earthing Strip Point and Ventilation Louvers at Rear Side, Bottom detachable Gland Plate complete with suitable size Zinc Chromium Plated Nuts, Bolts and Washers, etc. and embeddedwith 50X50X6mm Mild Steel Angle Iron Frame and 750 mm above the Normal Ground Level complete withinternal connection with suitable size of cable, cable lugs and cable glandsPCC Foundation in Cement Concrete 1:3:6 (20 mm Graded Stone Aggregate) and Testing after Installation includingcomplete all as specified and & directedby Engr-in-charge comprising of the following :– ( Booster terrace pump panel)INCOMING:-(a) INCOMING MCCB 40 A 25 KA, 4 POLE- 01 No.(b) Busbar TPN of size 100 apms - 1 setOUTGOINGS:-(a) MCB 3 POLE TPN 32 Amps,10 KA-2 Nos.(b)DOL Starter for 7.5 HP Pump set-1 Nos.(c) Ammeter Class-1, digital panel mounting type 96mmx96mm L & T cat no WDS301FCA00 including CT 50X5 Amps 3 nos & selector switch-4 nos(d) Voltmeter Class- 1, digital panel mounting type 96mmx96mm L&T CAT NO.WDS301FEV00 & selector switch - 1 no.(e) LED TYPE indicator lamp 1 set (set of three for R,Y,B)(f) Mini protecrionRelay 4-11 amp - 1 nos. 74 Fire Extinguisher mechanical Foam type trolly mouted of 9 Liters capacity. Ceasefire 9 litrs fire Extinguisher AFFF Foam type, External Cartridge type, Pressure Guage Gross weight 14.6 Kg, empty weight5.6 Kg, Can height 611 MM, Diameter 175 MM, Discharge time less than 60 Secs controllable discharge mechanism, Minimum 6 Mtrs, Applicable on Class A, B, can construction deep down & CO2 Mig welded Valve Construction: Forging & Machining, Internal coating of can: Epoxy powder coating, External coating of can: Epoxy poyster powder coating sheet metal thickness 2.0MM,1 year warranty. Make Cease Fire Or Equivalent. (pol store) 75 Supply, Installation,Testing & commissioning of Carbon Dioxide (Co2) type fire extinguisher of 4.5 Kg confirm to IS: 15683, with ISI marked/TAC approved fitted with required accessories including wall suspension brackets. 76 Supply, Installation,Testing & commissioning ofDRY CHEMICAL POWDER (ABC) stored pressure type fire extinguisher of 9 Kg confirm to IS: 15683, with ISI marked/TAC approved fitted with required accessories including wall suspension brackets. 77 Supply, Installation,Testing & commissioning of Water Mist High pressure stored pressure type fire extinguisher of 9 Kg confirm to IS: 15683, with ISI marked/TAC approved fitted with required accessories including wall suspension brackets. 78 Supply and installation at approved location approved make Fire sand bucket of 24 gauge galvanized steel sheet, each set shall have 4 buckets with stand & Showel etc, complete. 79 SPECIAL EQUIPMENTS FOR STORESDesign, manufacture, Supply, installation, testing and commissioning of Automated Storage and Retrieval System with storage racks, pallets, stacking crane, computer hardware with compatible inventory software as a turnkey solution complete all as specified and directed. Automated Storage and Retrieval System shall consist of computer controlled & PLC stacker crane driven system for automatically placing & retrieving materials from defined storage locations. The crane shall be capable of lifiting, stacking and retriveing the pallet loads weight upto 1125 Kg (max) complete all as specified and directed by the Engineer-in-Charge. Technical data for design of heavy duty ASRS:-(a) Dimensions:-Height:10 Mtrs for racking system which shall be designed and constructed to store the required no. and size of pallets.(b)Storage capacity:-Pallet Size: 1300 (W) x 1200(D) x 1250 (H) in mmPallet Nos.: 480Pallet load capacity: 1125 KgTotal capacity: 540 Tons(c) Stacker Crane: Single mast automated stacker crane for handling Pallet, size 1300mm(W) x 1200mm (D) x 1250mm (H) and pay load (including Pallet self weight) of 1125 Kg max. The stacker crane shall be capable of picking up the pallet from in-feed conveyor or loading station and stacking it into empty slots of racking system. Similarly, it shall also be capable of retrieving the palltet from racking system and putting it on the same conveyor or unloading station. Stacker crane will be mounted on single rail at the bottom to traverse the length of the storage system. A single top rail mounted on the racking system shall also support it.General technical parameters of stacker crane:Technical parameters/Type- Single Mast(i) Operation mode (Networking)- On-line automatic / Single automatic (Ground/Boarding) /Manual operation (Boarding) / Maintenance (ii) Communication Means- Wireless 80 (iii) Power supply mode- 380 to 415 V, 50 Hz, three phase five wire (iv) Addressing mode- Horizontal and verticle operation: photo electrical sensor + bar code scanners(v) Positioning / Reduction accuracy (mm) level- lifting ± 3 - 5, Fork : ± 3(vi) Fork unit- 1 Double deep fork(vii) Load unit- MS Pallet (viii) Total Height- 10 Mtr(ix) The normal lifting speed (m/min) - 10 MPM(x) The normal running speed (m/min) - 65 MPM(xi) Rated load- 1125 Kg(xii) Receipt equipment fixed platform/conveyor/lifting /platform(electric/manual)- Conveyor(d) Pallets: to stack and retrieve the pallet weighing up to loaded pallet weight 1125 Kg at height up to the last loading level in the racking system. It should have retrieval mechanism to enable stacking & retrieval of pallet from either side of the rack and also to pick up the load directly from the loading station.Pallet Details:-(i) Dimensions - 1300mm(W) x 1200mm(D)(ii) Pallet height- 1250 mm(e) Racking system :- Two aisle having two row racking system each with 05 verticle levels for storage of material. Racking for double deep type storage of 480 Pallet of size 1300mm(W) x 1200mm (D) x 1250mm (H). Loaded pallet weight: Pay load with pallet 1125 Kg max. System details:-Working aisle -01 Nos. (Double deep)Store rack -24 Nos./RowTotal rack in 1 aisle-24 (Left) + 24 (Right)= 48 Nos.No. of level- 5 Nos/RackTotal Pallet-48 x 5 x 2 = 480 Nos.Load capacity- 1125 Kg/LevelSingle mast stacker crane-01 No. 81 (f)Aisle Equipment:-This will consist of electrical as well mechanical aisle equipments and willl be designed as per the pallet requirement. The mechanical Aisle equipment of bottom rail shall consist of I Beam and will be provided with adjustable calmps for holding the rail in position to ensure proper alignment. Top rail shall be mounted on the racking. The electrical aisle equipment shall consist of power rail (fully enclosed bus bar having 7 pole system), which is mounted on the racking system below the first loading level.(g) Details of rack members:-The racking system shall consist of cold-rolled steel sections as per manufacturers design to accommodate and store pallets and connected systems.(h) Loading- unloading station/ Conveyor(i) Pallet Load 1125 Kg max.(ii) Bearing- SKF Equivalent make(iii) Motor- Seimens/Sew Euro Drive/Nord Sew/ Bonfiglioli or equivalent(iv) Gear Box- Bonfiglioli Make or equivalent(v) V.F.D.- Yashkawa make or equivalent(j) All steel surface shall be powder coated finish with 8 tank treatment process.(k) Maintenence: The annual maintenence of complete ASRS system duyring the defect liability period of two years shall be included in the rate quoted for the system and the AMC contract duly signed with the manufacturer of the ASRS system shall be submitted at the time of handling over the system. The AMC shall include all spares and consumables etc required during the period of two years and nothing extra shall be paid on this accountNote- 1Mechanical safety provision (i) End of aisle shock absorbers / bumpers for stacker crane.(ii) End of travel buffer for the lifting crane.(iii) Safety catches on lifting carriage.(iv) Anti-tilt mechanism for the stacker crane.(v) Continuous rail cleaning brush for floor rail.(vi) Adjustable rail clamp to ensure alignment. 82 (vii) Resilient rubber pads on adjustable clamps for vibration dampening.(viii) Profile check on lifting carriage to check all three dimensions (width, depth & height) of the pallet. Note - 2 Electrical safety provision (i) There shall be Emergency stop push button at all panels and stations.(ii) Optical light beam amd mechanical safety sensor to stop the operation in case of improper storage or obstruction in the operator window either internal or external reasons like operator hand or material placed at edge of the tray.(iii) Back up circuitry for proper system operation.(iv) An electromagnetic brake shall be used to avoid the slippage of the hoist.(v) Stopper shall be provided for the maintenance door.(vi) Load cells shall be provided for the over weight of tray.(vii) Automatic door shall be provided for operator safety while machine in operating condition.Note - 3 Physical safety provision (i) The ASRS system shall comprise of safety fences having grid size of max. 40 x 40mm & wire dia should be of min. 3 mm. Height of the fencing should be minimum 2.0 meter.(ii) One No. of electromagnetic aisle access door shall be provided. It should cover the complete length of the system on one side.(iii) A manual locking system to restrict the movement of unauthorised personnel shall be provided.NOTE: Design report shall be submitted before execution of Work at site by the contractor toGE for his scrutiny / comments and futher submitted to AO for obtaining approval. Item No. 13.070 below shall be compatible with this item/ system and both should be integratedMake of ASR system:Armstrong Ltd/ Godrej Koerber/ Kardex India storage solutions Pvt Ltd/ Daifuku India Pvt Ltd/ Addverb technologies Ltd/ Craftsman Automation Ltd/ Tech-mark 83 Supply, installation, testing and commissioning of Advance Inventory Management System with computer hardware with compatible inventory software complete all as specified and directed by the Engineer-in-Charge. Technical specification of the system(i) System Height : 6400 (±100) mm(ii) System Width : 3150 (±100) mm(iii) System Depth : 2300 (±100) mm(iv) System Base : 7.24 Sq.Mtr(v) Tray Int. Size: 300 (H) x 2450(W) x 500 (D) in mm(vi) Tray dead weight - 57 Kg (Approx.)(vii) Per tray weight capacity - 300 KgTechnical specification of the system:-(viii) Tray Quantity : 32 Nos.(ix) Usable net load - 9.6 ton(x) Storage surface area per system - 39.2 sq mtr(xi) Door - Automatic(xii) Power consumption - 3.7 KW(xiii) Power supply - 440V, 50/60 Hz, 3 Phase(xiv) Motor 3 Phase 1440 RPM - Seimens make or equivalent(xv) Chain - Diamond makeor equivalent(xvi) Bearing - SKF/NTN make or equivalent(xvii) External cladding - Epoxy powder coatedSafety Features:1. Photo curtain at access port, 2. Motor Protection relays, 3. Limit switch at door, 4. Single phase preventer,5. Switch mode power supply, 6. 15 Min battery backup for PLC, 7. Noise less than 60db, 8. Emergency stop various safety alertsNote: The system and software provided under this item shall be of same make as for item 13.069 or a compatible system and software as recommended by the chosen manufacturer of ASR system. This system shall be integrated with ASR system. 84 Supply, installation and testing of Car Traffic Boom Barrier 6 mtr suitable to working on power supply 230 Volt, 50 Hz, 24V DC electric motor, adjustable with CAMS, operating ambient temperature from -20 to +55 Degree Celsius, uses cycle 2000/Day, air cooling, type of beam is rectangular with skirt, effective torque 280-290 Nm open/close time 2 to 4 Sec complete all as specified and as directed by Engineer-in- charge.Make: FAAC/Parkilo/Skidata/BFT 85 EXTERNAL WATER SUPPLYSupply and fix Foot valve conforming to IS,100 mm dia complete all as specified and directed. 86 Supply and fix Cast iron air release valve with 100 mm bore and two outlets as per IS:14845 complete all as specified and directed. 87 Supply, installing, testing and commissioning of electrically driven horizontal Centrifugal Pump set 9.0 LPS at 50 Meter Head as per specification, motor TEFC type, 2880 rpm, 415 V, 50 Hz, 3 phase, class F insulation, IP 55 protection, starting on suitable Star Delta starter. The pump shall be horizontal, end suction, top discharge. The pump shall have cast iron casing, cast iron/bronze impeller (as per manufacturer), carbon steel shaft with common base frame (fabricated mild steel channel frame or cast iron type) placed on RCC (1:2:4) including foundation, bolts, nuts etc. complete with antivibrator pad as required capable of discharging not less than 550 LPM at 45 mtr head inclusive of suitable rated three phase starter as recommended by the manufacturer, PVC insulated copper cable connection from starter to the motor terminals all as specified and directed by the Engineer-in-charge.(01 No. Working + 01 No Stand By)Make:- Kirloskar Brothers/Crompton or equivalent. 88 Supply, install, test and commissioning of LT Panel, indoor type, powder coated, 2.0 mm thick CRCA Sheet, CPRI approved having, IP 43, MS angle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply, bus bar chamber with Horizontal copper bus bar for 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2.0 mm thick CRCA Sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. andcomprising as under: LT Panel for Pump House. The LT Panel comprising of the following:- 89 Incoming:-MCCB, thermal magnetic release, 4 pole, 415 Volts, 100 Amps, breaking capacity 36 KA- 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type)- 01 sets(b) Digital Multi function meter - 01 No.(c) CTs - 100/5A, CL-1, 15 VA - 01 set(d) Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 350 Amps for phase and 350 amp for the neutral barOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 63 Amps, breaking capacity 16 KA- 02 No. Ics =100% Icu -2 nos.(b) MCB, TPN 40 Amp, 415 Volt, C Curve - 02 Nos.(c) Star Delta starter 12.5 HP, 3 Phase, 415 Volt- 02 Nos.(d ) Digital ammeter - 2nos.(e) Single Phase Preventer - 2 nos. 90 M & L Valve chamber of internal size 0.90m X 0.90m X 0.90m (internal dimensions) including excavation of earth work in any type of soil, 150mm thick PCC in 1:4:8 type D2 foundation, brick work in CM 1:6, 15 mm thick rendering in CM 1:4 to internal surfaces and external surfaces upto 150mm depth below GL, PCC 1:3:6 type C1 as in coping, cover with two Nos. of hinges and one No. handle made out of MS round bar 10mm dia with necessary locking arrangement including painting to the steel surfaces with two coats of synthetic enamel paint over a coat of red oxide primer complete all as shown on drg and as specified. Note:- The quoted rate shall include all earthwork and connected items. 91 M & L Earthing complete with Galvanized steel earth plate electrode of size 600mmX600mm, 6.00 mm thick buried directly in ground vertically to a depth not less than 2.25 metres below the normal ground level with top edge of the plate not less than 1.5m below normal GL and connected to galvanized iron strip of size 32 x 6 mm size by means of bolts, nuts, check nuts and washers of galvanized iron steel all as shown in Electrical Plate No. 3 connecting to earthing test point, including necessary earth work in any type of soil, PCC earth chamber made in PCC 1:3:6 type C1 (using 20mm graded aggregate), common salt, charcoal, CI funnel, earth pit cover in RCC 1:2:4 type B1 (using 20mm graded aggregates), with 8mm CTD bars @ 100mm c/c in both ways, including necessary form work complete including necessary test on completion all as specified and as directed. 92 EXTERNAL ELECTRIFICATIONM & L for HT/LT MS cable route indicator, engraved the description on the disc not less than 6 dia welded with 40x6xmm MS strip of approx length 90 cm duly painted on the steel parts as per colour code and provision of PCC 1:4:8 type D-2 using 40 mm grade stone aggregate of not less than 0.05 cum in each at base under the ground including necessary earth work and formwork complete all as specified and directed.Note: HT route indicator shall be painted as under:-(i) For HT 11 KV cables - “BROWN”(ii) For LT cables - “BLUE” 93 Supply and fix compact air insulated bus bar trunking system with copper busbar 1600 Amps, 50 KA breaking capacity, IP54 protection, bus duct 1600 A, 415 Volt, capacity sandwich type, Set RYBN complete with accessories such as flange ends, vertical bends, supporting brackets etc from transformer to LT panel board complete all as specified and directed. 94 Supply, install, testing and commissioning of Distribution transformer step-down Level 2 (Previously EE Level 3 before Amendment No 4 to IS 1180), 11KV0.433KV, Three Phase complying withIS: 1180/IEC-76(Part-1) 2014 with latest amendments, indoortype double copper wound suitable for 50 Hz system of capacity 800 KVA, oil immersed naturally cooled delta connected on HT side and Star connected on LT side, Vector Group Dyn11, provided with OFF load tap changer to vary secondary voltage from -7.5% to + 7.5 % in step of 2.5 %.Losses should be confined to the limits specified as follows: maximum allowable losses atfull load (100 %) & Half Load (50 %) shall not be exceeded 5838 watts & 2147 Wattsrespectively as per GRlHA RATING, Percentage Impedance: 4.5%. Losses and Impedance are subjected to tolerance as specified in IS 1180. The transformers should be supplied with first filling of oil confirming to IS 335. The transformer should have both side cable end box with neutral brought out complete all as directed by Engineer - in -Charge, and installation of transformer shall be carried out as per IS-10028and comprising with the following standard fittings/Technical specifications:-(a) Lifting lug for transformer and tank.(b) Earthing terminal rating and diagram plate.(c) Air release device.(d) Oil filling inlet pipe with plug.(e) Drain outlet pipe with brass gate valve.(f) Conservator tank with oil level indicator(g) Silica jel breather(j) First fill of oil upto level including conservator tank with fresh new oil conforming to IS335.(k) Type of connection Delta/Star(l) Type of cooling: Oil and Natural Air.(m) Vector group: DYN 11.(n) Temperature rise over an ambient of 50 °C maximum.(o) Cable end box on both side for HT/LT cables of suitable size.(p) Provision of thermometer with pocket.(q) Provision of oil and winding temperature gauge. 95 Supply, install, test and commissioning of LT Panel, Indoor type, powder coated, 2.00 mm thick CRCA Sheet, CPRI approved having, IP 43, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal copper bus bar for 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air.The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 1.6 mm thick CRCA Sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. andcomprising as under: The LT Panel comprising of the following:- Main LT PanelHorizontal copper busbar for 3 phase, 440 volts, 50 Hz, 4 wire system of rating 1600 Amps for phases and 1600 Amps for Neutral. 96 Incoming:-Incomer:-ACB 4 Pole, 415 V, 50 KA with Thermal Magnetic Release (Manual Draw out type) of capacity 1250 AmpMetering Unit:- (a) R Y B Indications (LED Type)- 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 1600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 630 Amps, Ics =100% Icu, breaking capacity 35 KA, Ics =100% Icu- 02 No. (For DG AMF Panel & Spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for APFC Panel & FPB 2 Near bulk Store) (c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 320/315 Amps, Ics =100% Icu breaking capacity 36 KA- 01 No. (for FPB 1 Near Adm Block) (d) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 01 No. (for Existing Load)(e) MCCB, thermal magnetic release, 4 pole, 415 Volts,125 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for FPB 3 Near Auction Disposal Store)(f) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 03 No. (for MT Complex, Watch tower no 2, Guard room)(g) Digital Ammeter with suitable CT for each outgoing 97 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MS angle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables. Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.1 (Near Admn bldg) 98 Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 600 Amps for phases and 600 Amps for Neutral.Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for 2nd floor & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 160 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for 1st floor)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 63 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for G floor)( d) Digital Ammeter with suitable CT for each outgoing 99 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air.The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.2 (Near Bulk Store) Horizontal Aluminium busbar for 3 phase,440 volts, 50Hz, 4 wire system of rating 600 Amps for phases and 600 Amps for Neutral. 100 Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type)- 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 600/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for Equipment Load & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 125 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Bulk Store)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Watch Tower No. 1)( d) Digital Ammeter with suitable CT for each outgoing 101 Supply, install, test and commissioning of LT Panel, outdoor type, powder coated, 3.00 mm thick CRCA sheet, CPRI approved having, IP 54, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natural flow of air. The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 2 mm thick CRCA sheet, duly compartmentalised for each control gear with louvers and air vent gasket for natural flow of air and suitable provision to accommodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, crack resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.3 (Near Auction Disposal Store) 102 Horizontal Aluminium busbar for 3 phase, 440 volts, 50Hz, 4 wire system of rating 200 Amps for phases and 200 Amps for Neutral.Incoming:-(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 125 Amps, breaking capacity 25 KA- 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 200/5A, CL-1,15 VA - 01 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 100 Amps, Ics =100% Icu breaking capacity 25 KA- 02 No. (for Store Dispatch Complex & Spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 03 No. (for Pol store, Auction disposal store, Covered Hard Standing)(c) Digital Ammeter with suitable CT for each outgoing 103 Supply and fixing poly carbonate street light junction boxes IP 66/67 Weather proof suitable for outdoor installation having minimumsize255 x 355 x 122 including suitableCable connecting Terminals, Cable lugs, including provn of one No. MCB SP 6 Amps for operating the street light fittings, Suitable Cable Glands as per site requirement, all as directed by the Engineer-in-Charge. 104 S & F Street light bracket made out of GI tubing 32/40 mm dia, light grade of length1.2 mtr long bend to shape suitable for security light fitting with necessary MS clamp-02 Nos with one coat of anti corrosive primer and two coats of aluminium paint including nut, bolt, washers and 3 core FRLSinsulated sheathed, multistranded copper conductor of size 1.5 sqmm for phase and neutral and 1.5 sq mm for earthing drawn throughthe poles for connection from junction box to light fitting complete etc all as specified.Note: Phase should be Red/Yellow/Blue, neutral should be black and earthing wire should be green in colour. Two runs of cable for phase and neutral and one run of cable for earth will be measured and paid as one unit length. 105 Supply and fixing of LED flood light, 200W, watt 230 V, AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp and made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP protection incl system efficiency >110/120LPW 10KV SPD included Energy saving, environmental friendly and general purpose lighting complete all as specified and directed Engineer-in-Charge. Make : Make : Crompton/Philips/Wipro 106 Supply and fix High Mast Panel outdoor type, suitable to take load up to 6 KW, Conforms to IS/IEC 60947-4-1, Provided with Protection Degree IP 54, Extended wide band (150 Vac - 300 Vac) coil, FRLS (Fire retardant low smoke) Internal wiring, In-built Short-Circuit Protection, Class H Insulation, 3 Phase 415 Volts AC with the following accessories:Phase : 3 Phase, 415 VoltsMax Load Capacity : 6 KWTimer type: AstronomicalContactor Rating : 32 A TPMCB Rating : 63 A TPNMake : Crompton/ Philips/Wipro 107 Supply and laying DWC (Double wall Corrugated) duct pipe outer dia 63 mm and inner dia 50 mmconforming IS 16205 (Part 24 ) for protection ofelectric cable complete all as specified and directed. ( for 10 sqmm St light cable & 16 Sqmm cable) 108 AVIATION OBSTRUCTION LIGHTSupply and fix aviation obstruction light integral aviation light comprising of aluminium housing with polycarbonate enclosure, 240 volt with timer switch and one No.10 A, MCB, SPN 230 V with fixed enclosure complete all as specified and directed by Engineer-in-charge.Make:- Bajaj cat No BGAV 302 LED or equivalent in Philips/Crompton/Surya 109 INCINERATORSupply, fixing and testing of Solid waste Electric Incinerator, single chamber type having a combustion chamber supported with electric coil for generating sufficient heat to burn 100Kg/hr solid waste, retains and re-burns the exhaust gases for minimum of 2 seconds at 850°C, Stainless steel stack for longevity, fitted with a Velocity Cowl as standard, Chamber designed for maximum air flow and circulation which in turn improves efficiency and total burn time, easy to open and close loading door, designed to increase operator safety, steel cladding to reduce risk of infection and increase longevity of system with working temperature not less 450 degree Celsius mounted on foundation as recommended by OEM including electrical control panel with suitable size MCCB, relays & contactor recommended by OEM complete all as complete all as specified and directed.Note:(a) The electrical works including electrical LT panel, internal wiring of the LT panel, suitable size copper wires from panel to Solid waste Electric Incinerator as recommended by OEM to operate the Solid waste Electric Incinerator of capacity 100 Kg/Hr to make Solid waste Electric Incinerator operational is deemed to be included in the rate quoted. (b) All Electrical works shall be carried out as per relevant BIS/lS equivalent standard norms only and also in accordance with the latest edition of the Indian Electricity Act / rules formed there under and as amended from time to time.(c) Any other works (mechanical, electrical & Civil) connected to installation, testing & functional requirement of Solid waste Electric Incinerator of capacity 100 Kg/Hr all as mentioned above and which is not mentioned or included in this Schedule but required at site necessary shall be carried out by the contractor and quoted rate shall deemed to included for the same.(d) Foundation/Plinth/Base: shall be provided as per manufactures recommendations, however minimum 0.5m space should be available all around the Solid waste Electric Incinerator and height of plinth shall not be less than 0.5 M 110 Supply & fixing MCCB, thermal magnetic release, 4 pole, 415 Volts, 200 Amps, breaking capacity 36 KA- 01 No.Ics =100% Icu with Sheet metal enclosures fixed properly at directed location and connecting/testing complete all as directed. 111 ELECTRIC SIRENSupply and fixing Sirens Electronic type Horizontal Double Mounting Three Phase 400/440V, 2800 RPM 50 C/s Flame Proof, audible range 3.5 Km, 2 HP, continuous normal operation for at least 50 minutes with on/off system complete all as specified and directed. 112 Supply and fix advance Sirens controller Electronic type suitable to operate on 3 phase, 415 volt AC 50 Hzcomplete all as specified and directed. 113 Supply & fixing MCCB, thermal magnetic release, 4 pole, 415 Volts, 63 Amps, breaking capacity 25 KA- 01 No.Ics =100% Icu with Sheet metal enclosures fixed properly at directed location and connecting/testing complete all as directed. 114 SOLAR POWER PLANTDesign, supply, installation testing and commissioning of roof top solar photovoltaic power plant (ON-GRID) on roof top of existing bldg of capacity 150 KWp, power evacuation at 415 Volt 3 phase system all as per guidelines/norms issued by MNRE & Indian Metrological Deptt approved Solar Radiation Data viz Direct Normal Irradiance, Global Horizontal radiance etc complete comprising with the following Solar Photo Voltaic Plant.(a) Design, supply, installation, testing and commissioning of Solar PV Modules capable of generating 150 KWp (AC) electricity at 415 Volt 3 phase system. These Solar PV Modules of 540 watt PERC with a modular efficiency of 17-19.84% as per IEC and MNRE standard or as per approved design parameters with Poly/Multi Crystalline Silicon Solar cells of minimum wattage of 540 watt with minimum 144 cells & efficiency not less than 17 -19.84%, conforming to IEC 61215, IEC 61730, IEC 61701. Solar PV Module should be of approved Indian Brand only and Qualify under the Domestic Content requirement (DCR) norms of NVVN/SECI and testing requirement fixed by MNRE. The PV modules shall be warranted for a period of minimum 25 years, Solar PV modules used in system shall be warranted for their output peak watt capacity, which should not be less than 90% at the end of Ten years and 80% at the end of Twenty Five years. Each Solar PV Module must use RF identification tag. The following information must be mentioned in the RFID used in each module:Name of manufacture of PV module, Name of manufacturer of Solar cell, Month & year of manufacturer (for solar cell and module), Country of origin (lt is mandatory to use cells and modules manufactured in India). I-V curve of the module, Wattage, LM, V-M, & FF for the module, Unique Serial No & Model No of the module, Date & year of IEC PV qualification certificate, Name of the test lab issued IEC certificate. The PV modules used in the solar power projects must qualify to the latest edition of the following International Electro technical Commission (IEC) P module qualification test or equivalent BIS Standards. The PV module must be tested and approved by one of the IEC authorized test centres. 115 (b) Material and labour for Module Mounting structure (MMS) fabricated from hot dip galvansied iron section of suitable size with specified tilt angle according to site requirement & optimum angle to achieve maximum benefit of solar energy and suitable to withstand 180 Kmph wind speed all as per approved design parameters as per MNRE standards and to match with the existing site conditions. Necessary roof treatment to avoid any seepage in future shall be done by the Contractor and the amount included in the rate quoted. The roof tiles shall be dismantled and refixed back in original position. Structure shall be built with brick masonry basement of adequate size as per direction at site including all necessary civil work required for the foundation.(c) Supply, laying & Testing of DC cable minimum size 4/6sq mm multi stranded copper conductor, conforming to relevant IS, weather proof UV resistant with operating temperature up to 120 degrees, minimum rated voltage 1100 volt for inter connection of SPV Modules to array junction box including suitable size of cable lugs, male & female MC4 connectors & joints etc.(d) Supply, installation test and commissioning of protection devices MCCB 400 A, isolator and three phase 4 wire LT energy meter, array junction boxes having rating 150 KWp with over voltage protection and surge protection.(e) Supply, installation, test and commissioning of Grid tie Solar Power conditioning unit / inverter of minimum capacity 150 KWp(DC to AC 415 V in Three phase system) all as per approved design parameters & capable of generating output voltage 415 V AC at rated load condition with efficiency not less than 98 %, conforming to IEC 600682-2 NDE standards with power reduction, LVRT with protections for anti-islanding, Ground fault monitoring, Grid Monitoring, AC & DC Over voltage and under voltage protection, AC & DC short circuit lover current protection and DC reverse polarity protection, graphic display etc. all as specified and as directed.(f) Material and labour for Earthing for Lightning protection for SPV modules etc as per IE rule, MNRE guide line & BIS all as per approved plan complete with galvanised earth plate electrode 600x600x6 mm thick buried directly in ground vertically (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below normal ground level connected to and including Gl strip 32x6mm size protected with Gl medium grade pipe 40mm dia for earth electrode up to test point by means of GI nuts, bolts, check nuts and washers including earth work excavation, PCC (1:3:6) type Cl pit and RCC cover ( 1:2:4) type Bl and funnel, with necessary charcoal, salt etc complete. 116 (g) Supply and fixing aluminium strip of size 25 x 3mm thick for roof / down conductor fixed on insulators/ saddles of suitable size for SPV modules lightning protection upto interconnection between Roof top LA to Ground Earthing system. (h) AC Cable: Supply and laying of 150 Sqmm LT XLPE insulated, screened PVC bedded, sheathed with multi-stranded aluminium conductor armoured with galvanised steel wire 1100 volts grade heavy duty conforming to IS 150 Sqmm x 3.5Core as per site requirement.Note (i) :-(a) Before quoting the bid, Contractor or his authorised Engineer/consultant must visit the proposed site to study the site condition.(b) Before commencement of work, contractor shall submit drawings & lay out plan with scale including required qty to Accepting Officer for approval.Note(ii):-(a) The mechanical structures, electrical works and overall workmanship of the Grid solar power plant must be warrented for a minimum of 5 years.(b) All Mechanical, Electrical works shall be carried out as per relevant BIS/lS equivalent standard norms only and also in accordance with the latest edition of the Indian Electricity Act / rules formed thereunder and as amended from time to time.(c) Any other works (mechanical, electrical & Civil) connected to installation, testing & functional requirement of solar photovoltaic power plant of capacity 150 KWp (AC) all as mentioned above and which is not mentioned or included in this Schedule A but required at site necessary shall be carried out by the contractor and quoted rate shall deemed to included for the same(d) Contractor shall provide adequate Spares/items required for minimum period of 1 year maintenance including DC & AC items under scope of work.Note (iii) : Design report shall be submitted before execution of Work at site by the contractor toGE for his scrutiny / comments and futher submitted to AO for obtaining approval. 117 DG SETSupplying, installing, testing and commissioning, factory assembled silentDiesel Engine driven generator set, fully wired alternator AC to give an out put of 400 KVA continuously rating at a power factor 0.8 lagging, 3 phase 4 wire, 415 volts 50 Hzsupply, 1500 RPM, directly coupled with diesel engine liquid cooled mounted on common base frame complete with floor mounting fuel tank (service tank) of adequate capacity with fuel line & accessories, PCC foundation work as per manufacturers instructions, vibration damper pads, control panel & other accessories etc and comprising of following.(a)Diesel Engine: Liquid cooled turbo charged with after cooler to deliver suitable BHP at 1500 RPM under NTP conditions of BS 5514 and conforming to IS 10001/ 10002, DIN 6271 & ISO 3046 with an overload capacity of 10% for one hour in any 12 hours continuous operation with the following accessories:. Diesel engine of rated speed at full load electric start developingwithsystem with radiator and including electronic governor control of class A1, engine control panel, lub oil pump, water pump, fuel tank, exhaust pipe with silencer and suitable for electric start with batteries ofadequate capacity and suitable for alternator of specified capacity complete with fly wheel direct/flexible coupling and coupling guard complete.(a) Radiator with blower fan or heat exchanger with guard.(b) Pipe coupling for engine cooling system piping.(c ) Corrosion inhibitor coolant(d) Paper element filters(i) Fuel filter(ii) Lube oil filter(iii) By pass(e) Fly wheel housing and fly wheel to suit alternator.(f) Engine bearing mechanism in fly wheel housing.(g) Shut off coil with safeties for LLOP/HWT/over speed.(h) Dry type air cleaners and vacuum indicators.(j) Residential silencers.(k) Stainless steel exhaust flexible bellows. 118 (l) Motor driven priming pump.(m) Battery charging alternator.(n) Exhaust piping made out of STIC C class, MS pipe inclusive of all accessories and hardware, necessary supports scaffolding as per manufacturers recommendations to sustain back pressure with rain cap.(o) Mineral wool insulation 2 inch thick suitable for 400 degree Celsius temperature cladded with aluminium sheet o30 gauge for the entire length of exhaust pipe.(p) First fill of oil, coolant and diesel during commissioning and 12 hours testing.(q) Interconnecting copper cabling of adequate capacity batteries control.(r ) Fuel pipe class STIC 1 /1.5 /2 dia - 01 lot(s) Self starter 12 volts DC.(t) Electric operated electronic governor.(u) Fuel injection pump.(v) No of cylinders - 12 No VEE(w) Electronic instrument panel, complete with all accessories as per manufacturers specifications displaying the following:-(i) 12vx2 nos -24V Battery. (ii) Water temperature.(iii) lubricating oil pressure.(iv) Engine speed -1500Rpm(v) Engine hours(vi) Frequency.(vii) Voltage.(w) Safety control (Trip and indication).(i) High water temperature(ii) Low lube oil temperature(iii) Overspeed stop 119 (x) Base frame: Sturdy, fabricated welded construction, channel iron base frame (duly painted) for mounting engine and alternator as per manufacturers design alonwith AVM pads.(y) Battery:-24 volts(2x12v Battery) DC, 180AH, maintenance free battery conforming to IS:14257 with leads & terminals (Make- Excide/Amron).(z) Fuel tank:12 hrs. full load diesel storage capacity fuel tank with mounting brackets factory made of 5mm thick HR/MS sheet with level indicator fuel inlet, fuel outlet, air vent, drain plug, in let arrangement for diesel filling fro exterior canopy (without opening its panel) etc complete all as specified and directed.(aa) Isolator panel with 250 amp MCCB(ab) Auto logic panel for automatic stat(b) Alternator: Alternator suitable rated for 400 KVA, 0.8 pf , 415 volts, 3 phase, 4 wire, 50 Hz at 1500 RPM, self excited and self regulated with AVR brushless, screen protected, drip proof , insulation class-H, IP -23, voltage regulationgrade - VG 3 self ventilated and conforming to BS: 5000 / IS: 4722 suitable for engine as mentioned here-in before, conformig to IS: 13364(part-1)Make: KOEL GREEN / stampford/crompten/kirloskar/Greaves(c) Acoustic Enclosure:- M & L for acoustic enclosure for the above 400 KVA DG set to reduce noise level to 75 dB measured at 1.0 meter distance for audible frequencies as per guide of Central Pollution Control Board andmanufacturers specification and comprising of following from authorised GOEMs of Gen Set manufacturers specified :-(i) Sound insulation : 100mm thick Rock wool (Density 64 Kg/Cum).(ii) Outer body : 1.6mm thick CRCA(iii) Door : 1.6mm thick CRCA(iv) Base frame : ISMC 300(v) Inside illumination : 1 No.- 1 x 18 watt LED fitting of make Phillips/ Bajaj/ Crompton.(d) AMF Control panel:- Factory fabricated cubicle type, free standing, floor mounted, indoor type, IP-43, AMF control panel, provided with removable rear panels & hinged front panel for easy accessibility, fabricated out of not less than 2.0mm thick CRCA sheet including two coats of powder coated paint over a coat of red oxide primer etc and comprising of following: 120 (e) AMF control circuit with 4 pole MCCB 630 Amps - 2 nos, with ultimate breaking capacity Icu-50 KA at 415 volts and microprocessor release conforming to IEC 60947 Part-I with breaking capacity Ics=Icu at 415 volts , thermal overload setting 70% to 100%, short circuit setting 5 to 10 times-02 Nos. for main supply & DG set supply with HRC back up fuse complete with all DC control relays/ Line voltage monitor (LVM) as per OEM specifications incorporating motorised stored energy operating Engine start, stop, three attempt starting facility and failure to start etc.(f) Digital load manager : Three phase 4 wire indicating V,I,PF, KVA, KW, F of Enercon make with serial communication port model No.EM6400 with class 1.0 accuracy meter or equivalent make suitable rating of CT per phase- one No.(iii) Indication lamp R, Y, B with 3 Nos. of 2A HRC fuses-10 sets.(iv) Bottom gland plate for incoming and outgoing cables.(v) Circuit diagram plate.Note :- DG set should be as per CPCB -4 latest norm wef 01 July 2023 of National Clean Air programme (NACP) Act 1981. 121 Supply, install, test and commissioning of LT Panel, Indoor type, powder coated, 2.00 mm thick CRCA Sheet, CPRI approved having, IP 43, MSangle iron section of 50X50X6 mm frame, suitable for 3 Phase 415 volts 50 Hz, AC supply,bus bar chamber with Horizontal aluminium bus bar 3 phase and neutral 4 wire system duly insulated with heat shrinkable type sleeves as per colour code, supported on epoxy insulators, factory fabricated, roof canopy, with front and back openable double door system lockable/openable by keys from both sides, louvers & air vent gasket for natuaral flow of air.The bottom of the outer shell contains a detachable plate having provision for entry of armoured cable of adequate size with glands. The inner shell be made out of 1.6 mm thick CRCA Sheat duly compartmentalised for each control gear with louvers and air vent gasket for natuaral flow of air and suiatable provision to accomodate incomer/outgoing MCCBs/MCBs and metering devices and suitable busbar chamber for passing and connecting UG cables.Providing bus bar for phases and neutral and shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size F class insulators made on non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval of not more than 300 mm through out the length of the TPN bus bar all as specified and directed by the Engr-in-Charge. Feeder Panel No.1 (DG Panel ) 122 Incoming:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 630 Amps, breaking capacity 36 KA - 01 No. Ics =100% IcuMetering Unit:- (a) R Y B Indications (LED Type) - 1 sets(b) Digital Multi function meter - 01 No.(c) CTs - 800/5A, CL-1,15 VA - 1 setOutgoing:-(a) MCCB, thermal magnetic release, 4 pole, 415 Volts, 400 Amps, Ics =100% Icu breaking capacity 36 KA- 02 No. (for Package AC Bulk Store & spare)(b) MCCB, thermal magnetic release, 4 pole, 415 Volts, 160 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Pump House & Fire Pump)(c) MCCB, thermal magnetic release, 4 pole, 415 Volts, 80 Amps, Ics =100% Icu breaking capacity 25 KA- 01 No. (for Incianator)(d) MCCB, thermal magnetic release, 4 pole, 415 Volts, 32 Amps, Ics =100% Icu breaking capacity 25 KA- 07 No. (for Terrace pump 1, Terrace pump 2, Power House, High mast 1, High mast 2, Street Light)(e) Digital Ammeter with suitable CT for each outgoing(f) Astro Time switch for 3 phase 20A- 1 No(g) 3 Phase Power contactor 20 amps, with 230 coil 123 SEWAGE DISPOSALM & L for laying of DWCPE sewage pipes line 200 mmdia borepipe sftiffnessclass SN 8 includingsealing of joints fittings etc complete with collers complte all as spcified and directed 124 M & L for laying of DWCPE sewage pipes line 150 mmdia borepipe sftiffnessclass SN 8 includingsealing of joints fittings etc complete with collers complte all as spcified and directed 125 COMPOUND WALLS & F Concertina Coil of 600/700 mm outer dia made out of 2.60 mm dia spring steel wire dipped in corrosion preventive fluid (rusilo 901) of castrol make each coil having min 50 turns (circles) covering 6 m and an average weight not less than 8.57 Kg (plus or minus 5 %) incl handle and spike at both ends of coil erected in position on top of mild steel angle by fixing with 1.70 mm GI wire for securing, coil with fish hook bars, incl necessary welding to MS Sections etc all as specified and directed. 126 GREEN BUILDING NORMS(GRIHA CONCEPT)Supply and Install Organic Waste Converter fully automatic having capacity 50Kg/day, having internal tank made of high quality stainless steel while external panels are powder coated for enhanced product life with necessary electric control panel, cabling necessary civil works for installing machine etc with following requirements:-Type of machine: Fulley automatic in-vessel composterComposting method: 24 Hrs. Micro-organisms-based compostingmachine Type of microganism used: Heat resistant thermophilic bacteria Final Output: Dry organic Soil conditioner/Soil supplementsCycle time: 24Hrs Volume reduction in 24Hrs: 80-85% Internal tank: Stainless steel type Main agitator Shaft: Stainless steel type Input voltage: 415VSpecial features: VFD as standard across all models, Touchscreen standards Daily waste processing: 150Kgs Rated capacity: 7KWPower consumption (KWH par cycle): 13-15Length: 1650, Width: 850,Height: 1455 127 Supply, installation, testing and commissioning Three phase energy meter with the following specifications: Microprocessor based three phase, smart electricity meter, equipped with a bi-directional cellular (NB-IoT) communication that allows it to interact with the head end system (HES) for data collection and configuration with adequate security including electronic static pre paid cum postpaid energy meter rating 415 Volts, 50 Hz of range 10-100 Amps, complying to IS16444:2015 (reaffrimed 2020) and conforming to IS 3779 with LED display and parameters like Voltage, Current, Frequency, Power, Power factor, KWH/KVA, default in built dual source, inbuilt long range (LORAWAN) Communication suitable for outdoor LoRa data accumulator and also compatible for Prepaid and Postpaid online energy monitoring billing system with disconnection /reconnection through remote software / data export to ERP complete with 5 Years warranty.Note:(a) The contractor would be responsible for removing the existing meter, noting down the reading and depositing it with the MES AGE E/M store complete all as specified & directed.(b) The Energy Meter to be capable of running in both prepaid and postpaid mode.(c) The meters to carry 5 year warranty. (for entire system) 128 Supplying, Fixing, Commissioning and testing of configuration of cloud Hosted multi user web based software with following modules:(i) Head End System (HES): to acquire meter data automatically from DCU sand monitor parameters acquired from meters.(ii) Meter Data Management ModuleThe meter data management module would be responsible for collecting the data from the data concentrator and make the data available to the billing system. The system would support offline meter(a) 30 min instantaneous data from all the meters for seven parameters Cumulative Energy. Cumulative Apparent Energy (as applicable), Power, Current, Voltage, Power Factor and Frequency(b) Monthly billing survey data for cumulative energy and max demand(iii) Billing Module: The billing module would collect the data from the meter data management module, calculate the energy consumption, calculate billing determinant and make energy data/billing data available to admin and end users. The billing module would include functionalities for tariff setup, bill format setup, bill adjustment, occupation billing and vacation billing. It would allow postpaid and prepaid functionality as required.(iv) Occupation and Vacation Module: The system would support occupation/vacation based on the unit catagories. The system would support automatic data capture on occupation and vacation events.(v) Website: There would be a dedicated website forAGE/GE and BSO team to view all the data and information alongwith customer portal for use of customer. The designated users in MES would have the admin access to the application. The MES Staff would also have the access to the key information on mobile App (AndroiandiOS based) for admin use complete all as specified and directed.(vi) Customer Module: The system would include a customer portal for the resident/occupants to login and view their own energy /billing data and recharge facility. There shall be consumer App (Android and iOS based) also to log in and view their own energy/billing data and recharge facility.(vii) Communication Module :The system would provide communication of energy data and bills via print, email and sms methods. 129 (viii) Meter Master Data: The system would support meter data repository. The system would support meter replacement process.(ix) Excel Export: the system would support export of metering and billing data in excel and pdf format.(x) Energy Accounting module: The system would include features of energy accounting, the system would to able to account for total energy block wise, facility wise and would also allow calculations of the unaccounted energy in case total energy meter is also available.(xi) Prepayment/Recharging Facility:The system should periodically monitor the energy consumption of prepaid consumers and decrease the available credit based on the consumption. The system should allow online/digital recharging through consumer App (Androidand iOSbased) and Web portal. The configuration and necessary arrangement for payment gateway and E-MRO facility shall be deemed to be included in the quoted rate. The system should sendconnect/disconnect command on the basis of available credit.Low credit alarm: The system will give an alarm over the consumer App and SMS to the registered mobile number in case the credit in the meter goes down be low apredefined limit.Emergency credit: The meter will work even when the credit falls down to zero to prevent disconnection. This limit shall be configurable. The system should support happy hours inorder to prevent disconnection in non working hours and on holidays. The Happy hours should be configurable complete all as specified and directed. 130 Supply, Installation, Testing and Commissioning of DCUs/Gateways and the arrangement of Sim cards or Internet to enable reliable medium for two-way communication between Smart Meter & HES. The data acquisition (Push/Pull) frequency shall be, configurable. It shall push events such as tamper, power off etc. to HES immediately on occurrence/receipt from meters. It shall have provision for the cellular, WiFi and Ethernet communication for the backhaul to HES. It shall be capable to handle data of minimum 1000 Nos. of any type of smart meter (1ph/3ph).It shall be able to communicate with the nearest meters at a distance of at least 500 m, depending on topographical features. Communication of the nearest meters with other meters shall be established through appropriate mesh formation. RF Mesh shall support self-forming and self-healing features. The equipment shall be weather proof and dust proof (minimum rating: IP54 for indoor and IP65 for outdoor installation). It shall have rechargeable battery with backup for 1(one) hour for normal meter reading, to push tamper event, carry out on demand reading, etc complete all as specified and directed. 131 Hosting GPRS (4G) charges for Gateway for five years from the date of completion F Including 2 years waranty and 2 years Maintinance after warranty) Make:-Airtel/Jio/Vodafone 132 Supply and installation of digital Water flow meter 50mm suitable for domestic and commercial applications complete all as specified and directed. 133 Supply and installation of digital Water flow meter 40mm suitable for domestic and commercial applications complete all as specified and directed. 134 ARBORICULTUREM & L for excavation of pits size 30cm x 30cm x 30cm in loose soil and filling the pit with mixture of river sand and approved top soil in the proportion of 1:3 mixed with 30% of cow dung powder, 100gms of bone meal and 100gm of neem cake powder 135 All as per item No 13.121 above but pit size 60cm x 60cm x 60cm 136 Supplying and planting red palm or royal palm healthy sapling having 45cm height and shall have a minimum height of 65cm after 6 months 137 Supplying and planting coconut tree healthy sapling having 75cm height and shall have a minimum 95cm after 6 months. 138 Supplying and planting flower plants(Champa/ hybrid hibiscus/ Hybrid west Indian Jasmine/ Hybrid Plumeria white plant/ Panama yellow plant/ Oleander) healthy sapling having 10cm minimum height and shall have a minimum 25cm to 30cm height after 6 months. 139 Supplying and planting phylanthus healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 140 Supplying and planting bougainvillea colour flower plants healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 141 Supplying and planting song of India flower plants healthy sapling having 15cm to 30cm height and shall have a minimum 45cm height after 6 months. 142 Supplying and planting dracaena flower plants healthy sapling having 15cm to 30 cm height and shall have a minimum 60cm height after 6 months. 143 Supply and planting mexican grass including providing manure as directed. 144 PILE FOUNDATIONBoring 450 mm dia piles to any depthin any type of soil/ strata by anyapproved method, complete all as shown on drawings and as specified anddirected.Note:- The quoted rate shall include for mobilization and demobilisation of piling equipment, making approaches to site or point of pile boring if necessary. Nothing extra shall be paid on this account. 145 Boring for bored cast in situ pile 600 mm dia to any depth through any type of soil / strata, using DMC method (Direct Mud Circulation)and getting out & disposal of spoil to any distance outside of MD land , complete all as specified and as directedby the EngineerIn Charge 146 M & L Reinforced cement concrete of grade M-35 design mix (RMC) as per IS-456using 20 mm graded stone aggregate in cast in situ DMC bored pile of any length / any sectionscomplete all as specified and as shown on drg 147 M & L Reinforced cement concrete of grade M-35 design mix (RMC) as per IS-456using 20 mm graded stone aggregate in pile caps / grade beams complete all as specified and as shown on drg 148 Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10 mm dia and over for bored cast in situ piles of any length and any dia all as shown on drgs including cut to length, bend to required shape, cranking/hooking ends if necessary and binding with and including 0.9mm dia MS wire (annealed) or welding so as to secure the bar firmly in position/ required shape complete all as specified and shown on drgs (Fe-500D). 149 Providing TMT bars (CRS/HCRM/CRM) in reinforcement 10 mm dia and over for pile caps and grade beams, cut to length, bent to shape required, hooking ends and binding with and including 0.9mm dia MS wire (annealed) or welding so as to secure the bar firmly in position/ required shape complete all as specified and shown on drgs (Fe-500D). 150 All as per item No 13.136 here-in-before but5mm dia and over upto and including 10mm dia as in helicals for piles and stirrups for grade beams complete all as specified and directed. 151 M & L for providing PCC (1:4:8) type D-2 using 40 mm graded stone aggregate for concrete layer below pile caps foundation complete all as specified and directed. 152 Formwork to sides of pile caps/ grade beams and similar work, rough finished surface of concrete flat all as specified and as directed. 153 M & L for carrying out non destructive integrity test all as per IS 2911 (Part 4) 2013 for 600 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed all as specified and directed. 154 M & L for carrying out Initial Load test (vertical load test) cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013 including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 155 M & L for carrying out Initial (lateral load test) cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 156 M & L for carrying out Initial load test ( pull outtest) of cast in situ piles of 600 mm dia as per IS 2911 (Part 4) 2013including mobilising and removing the testing equipments from site after testing is completed all as specified and directed.(Note :- Providing and installing test piles shall measured and paid separately) 157 M & L for carrying out Routine load Test (Vertical load)all as per IS 2911 (Part 4) 2013 for 600 mm dia cast in situ piles including mobilising and removing the testing equipments from site after testing is completed 158 Testing of piles (Initial load test) for 450mm dia cast in situ bored piles all as per IS including removing the testing equipments from the site after testing is completed all asspecified and as directed

BRR : 7625205 Medicine Suture Surgical Material Pathology Item General Item Machinery Equipment , Medicine, Suture Surgical & Material, Pathology Item, General Item & Machinery Equipment , Tab. 5-Fluro Uracil500 Mg , Tab. Abacavir 300 Mg , Tab. Aceclofenac + Paracetamol + Serrapeptidase 100 + 325 +10Mg , Tab. Aceclofenac + Paracetamol + Serrapeptidase 100 + 500 +15Mg , Tab. Aceclofenac 100 Mg+ Paracetamol500 Mg +Chlorzoxazone 500Mg , Tab. Aceclofenec 100Mg , Tab. Acetazolamide 250 Mg , Tab. Acetylsalicylic Acid (Aspirin) 25 Mg , Tab. Acetylsalicylic Acid 150 Mg , Tab. Acyclovir 200 Mg , Tab. Acyclovir 800 Mg , Tab. Albendazole 400 Mg , Tab. Allopurinol300 Mg , Tab. Allopurinol 100 Mg , Tab. Alprazolam 0.25 Mg , Tab. Amiodarone 100 Mg , Tab. Amlodipine 5 Mg+ Atenolol 50Mg , Tab. Amlodipine 10 Mg , Tab. Amlodipine 5 Mg , Tab. Ambroxol 30Mg+Salbutamole 2 Mg+Theophylline 100 Mg , Tab. Amoxycillin+Clavulanic Acid (Amoxycillin 500 + Clavulanic Acid 125Mg) , Tab. Amoxycillin+Clavulanic Acid (Amoxycillin 200 + Clavulanic Acid 28.5Mg) , Tab. Amoxycillin+Clavulanic Acid (Amoxycillin 250+ Clavulanic Acid 125Mg) , Tab. Artemether (A) + Lumefantrine (B) 20 Mg (A) + 120 Mg (B)1X6 , Tab. Artemether (A) + Lumefantrine (B) 80 Mg (A) + 480 Mg (B) , Tab. Artemether (A) + Lumefantrine (B)Oral Liquid 80 Mg (A) + 480 Mg (B)/5 M , Tab. Ascorbic Acid (Vitamin C)100 Mg 100 Mg , Tab. Aspirin 75 Mg , Tab. Atenolol 50 Mg , Tab. Atenolol100 Mg , Tab. Atorvastatin 10 Mg , Tab. Atorvastatin 40 Mg , Tab. Azithromycin 250 Mg , Tab. Azithromycin 500 Mg , Tab. Baclofenbaclofen 40 Mg , Tab. Betahistine 8 Mg , Tab. Betamethasone 0.5 Mg , Tab. Bicalutamide 50 Mg , Tab. Bisacodyl 5Mg , Tab. Bisacodylsuppositories 5 Mg , Tab. Calcium Carbonate . 500 Mg , Tab. Calcium 500 Mg , Tab. Calcium Leucovorin50mg , Tab. Calcium With Vitamin D3calcium Equivalent To 500 Mg & Vit. D3 250 Iu , Tab. Capeciine500 Mg , Tab. Carbamazepine 200 Mg , Tab. Carbimazole 10 Mg10strip , Tab. Carboplatin450 Mg , Tab. Cefixime 200 Mg , Tab. Cefixime 50 Mg , Tab. Cefixime 100 Mg & Of0loxacin 100 Mg Dispersible , Tab. Cefixime 200 Mg & Azithromyin 250 Mg , Tab. Cefpodoxime + Clavunate 200+125Mg , Tab. Cefpodoxime- 200 Mg , Tab. Cetirizine 10 Mg , Tab. Cetirizine 5Mg+Ambroxol 60 Mg , Tab. Chloroquine 250 Mg , Tab. Chlorpromazine 100 Mg , Tab. Chlorthalidone12.5Mg , Tab. Chlorthalidone25mg , Tab. Cinnarizine 25 Mg , Tab. Ciprofloxacin 250 Mg , Tab. Ciprofloxacin 500 Mg , Tab. Cisplatin50 Mg , Tab. Clarithromycin 250 Mg , Tab. Clofazimine 100 Mg , Tab. Clofazimine 50 Mg 4 , Tab. Clomiphene Citrate50 Mg , Tab. Clonazepam 0.5 Mg , Tab. Clopidogrel 75 Mg , Tab. Clotrimazole (Vaginal )Pessary 500 Mg (With Applicator)Single , Tab. Clozapine 25 Mg , Tab. Clozapine 50 Mg , Tab. Cyclophosphamide500 Mg , Tab. Dapsone 100 Mg , Tab. Deferasirox 250Mg , Tab. Deferasirox 500 Mg30 , Tab. Deferiprone 500Mg , Tab. Deriphylline Sr 300 Mg , Tab. Dexamethasone 0.5 Mg , Tab. Diazepam 5 Mg , Tab. Diclofenac 50 Mg , Tab. Diclofenac 50 Mg+Paracetamol 500Mg , Tab. Diclofenac 50 Mg+Serrtiopeptidase 15 Mg , Tab. Dicyclomine 500 Mg , Tab. Dicyclomine Hydrochloride 20 Mg , Tab. Diethylcarbamazine 100 Mg , Tab. Digoxin 0.25 Mg , Tab. Digoxin 250 Mg , Tab. Diloxanide Furoate 500 Mg , Tab. Diltiazem 60 Mgl , Tab. Diltiazemsr90 Mg , Tab. Diltizem 30 Mg , Tab. Diphenylhydantoin 30 Mg , Tab. Dispersablehydroxyurea100 Mg , Tab. Disulfiram 250 Mg , Tab. Docetaxel120 Mg , Tab. Domperidone 10 Mg , Tab. Donepezil 5 Mg , Tab. Doxorubicin50 Mg , Tab. Drotaverine 40 Mg , Tab. Empagliflozin25 Mg , Tab. Enalapril Maleate 10 Mg , Tab. Epirubicin100 Mg , Tab. Erlotinib 150 Mg , Tab. Escitalopram 10 Mg , Tab. Ethamsylate250 Mg , Tab. Ethinylestradiol (A) + Levonorgestrel (B) 0.03 Mg (A) + 0.15 Mg (B) , Tab. Ethinylestradiol 0.01 Mg , Tab. Ethinylestradiol 0.05 Mg , Tab. Etophylline+Theophylline 100 Mg (Etophylline 77+Theophylline 23 )Mg , Tab. Etoposide100 Mg , Tab. Etamsylate 250 Mg , Tab. Exemestine 25 Mg , Tab. Ferric Carboxymaltose250mg , Tab. Ferrous Ascorbate(100Mg. Elemental Iron+Folic Acid 1.5 Mg) , Tab. Finofibrate160 Mg , Tab. Finofibrate 40 Mg , Tab. Fluconazole 150 Mg , Tab. Flunarizine 5 Mg , Tab. Fluoxetinecapsule 20Mg , Tab. Folic Acid 5Mg , Tab. Furazolidone 100 Mg , Tab. Furusemide 40 Mg , Tab. Gabapentin 300Mg & Methylcobalamin 500Mg , Tab. Gefitnib 250 Mg , Tab. Gemciine1.4 Mg , Tab. Glibenclamide 5 Mg , Tab. Gliclazide 80 Mg , Tab. Glimeperide 1 Mg , Tab. Glimeperide 2 Mg , Tab. Gutta Percha (Gp)30/Bottel , Tab. Haloperidol 5 Mg , Tab. Hydrochlorothiazid 12.5 Mg , Tab. Hydrochlorothiazid 50 Mg , Tab. Hydrochlorothiazide 25 Mg , Tab. Hydroxychloroquine 200 Mg , Tab. Hydroxyzine25 Mg , Tab. Ibuprofen 400Mg , Tab. Imatinib Mesylate400 Mg , Tab. Imipramine 25 Mg , Tab. Iron & Folic Acid Sugar Coatediron And Folic Acid Sugar Coateddried Ferrous Sulphate Ip Eq. To 45 Mg Ferrous Iron And 400 Mcg Folic Acid Ip (Pink Colored ) - , Tab. Iron & Folic Acid Sugar Coatediron Folic Acid Sugar Coated (Blue ) Ferrous Sulphate Ip Equivalent To60 Mg Elemental Iron & 500 Mcg Folic Acid Ip , Tab. Iron & Folic Acid Sugar Coatediron Folic Acid Sugar Coated (Red ) Ferrous Sulphate Ip Equivalent To60 Mg Elemental Iron & 500 Mcg Folic Acid Ip , Tab. Isosorbide -5-Mononitrate 20 Mg , Tab. Isosorbide Dinitrate 5 Mg , Tab. Itraconazole/Capsule 100 Mg , Tab. Ivermectin 12 Mg , Tab. Ketorolac10 Mg , Tab. Labetalol 100 Mg , Tab. Lenalidomide 25 Mg , Tab. Letrozole 2.5Mg , Tab. Levetiracetam 250 Mg , Tab. Levodopa (A) + Carbidopa (B) 100 Mg (A) + 10 Mg (B) Cr , Tab. Levodopa (A) + Carbidopa (B) 100 Mg (A) + 25 Mg (B) Cr , Tab. Levodopa (A) + Carbidopa (B) 250 Mg (A) + 25 Mg (B) , Tab. Levofloxacin 250 Mg , Tab. Levofloxacin 500 Mg , Tab. Levonorgestrel 0.75 Mg , Tab. Levothyroxine 100 Mcg100per Bottle , Tab. Levothyroxine 50 Mcg100per Bottle , Tab. Linezolid 600 Mg , Tab. Lithium Carbonate 300 Mg , Tab. Loperamide 2 Mg , Tab. Lorazepam 1 Mg , Tab. Losartan10 Mg , Tab. Mebeverine 200 Mg10 X 15 , Tab. Medroxy- Progesterone 10 Mg , Tab. Mefenamic Acid + Drotaverine , Tab. Metformin + Gliclazide 500+80Mg , Tab. Metformin 500 Mg , Tab. Metformin-Sr1000mg10x15 , Tab. Methotraxate50 Mg , Tab. Methyl Ergometrine Maleate 0.125 Mg , Tab. Methyldopa 250 Mg , Tab. Methylprednisolone 16 Mg , Tab. Methylprednisolone 4 Mg , Tab. Methylcobalamin. 1500 Mg, Vitamin D3 1000 Iu, Folic Acid 1.5 Mg, L-Arginine 250 Mg, L-Carnitine 250 Mg, L-Tartrate & N-Acety Cysteine Usp 250 Mg , Tab. Medroxypogesone Acetate 10 Mg , Tab. Methylcobalamin, Folic Acid And Pyridoxine Hci Oral Disintegrating 1500Mcg, 5Mg & 20Mg , Tab. Metoclopramide 10 Mg , Tab. Metoprololsr25 Mg , Tab. Metoprololsr/Plain50 Mg , Tab. Metronidazole 400 Mg , Tab. Mifepristone 200 Mg1 Per Pack , Tab. Misoprostal 100Mcg , Tab. Misoprostal 200 Mcg4in 1 Pack , Tab. Misoprostol 200Mcg (Oral/ Vaginal) , Tab. Montelukast 5 Mg , Tab. Morphine 10 Mg , Tab. Morphine+I469sr/30 Mg , Tab. Multivitamin Sugar Coated Nfi Formula Sugar Coated Vit A 2500 Iu , Vit C 50Mg, Calcium Pantothenate- 1Mg,Vit B1 2 Mg Vit B6 0.5 Mg Vit D3 200 Iu Vit , Tab. Nicotinamide 50 Mg7 , Tab. Nifedipine 10 Mg , Tab. Nitroglycerine (Glyceryl Tri Nitrate)Sub-Lingual0.5 Mg10 , Tab. Norfloxacin 400 Mg , Tab. Norfloxacindispersible100mg , Tab. Ofloxacin200 Mg , Tab. Ofloxacin400mg , Tab. Olanzapine 5 Mg , Tab. Olanzapine10 Mg , Tab. Ondansetron 4 Mg , Tab. Ormeloxifene 30 Mg , Tab. Omeprazole, Domperidone 20+10 Mg , Tab. Oxaliplatin100 Mg , Tab. Paclitaxel260 Mg , Tab. Paracetamol 500Mg , Tab. Paracetamol 650Mg , Tab. Paracetamol 325Mg + Diclofenac K 50Mg + Streptopeptidase 120Mg , Tab. Paracetamol Chlorzoxane & Diclofenacsodi Pot 325Mg + 250Mg + 50Mg , Tab. Paracetamol 170Mg + Dextromethorphanhbr5mg+Chlorpheniraminemaleate 1.5Mg+Phenylephrine Hcl2.5Mg , Tab. Penicillin V (Phenoxymethyl Penicillin)250 Mg , Tab. Phenobarbitone 30 Mg , Tab. Phenobarbitone 60Mg , Tab. Phenytoin/ Diphenylhydantoin 100Mg , Tab. Povidone Iodinevaginal Pessary 200Mg10 X 10 , Tab. Prednisolone 10Mg , Tab. Prednisolone 20 Mg , Tab. Pregabalin 75Mg And Nortriptyline 10 Mg , Tab. Prednisolone 20Mg , Tab. Prednisolone 30Mg , Tab. Prednisolone 40Mg , Tab. Pregabalin 150 Mg , Tab. Primaquine 15 Mg , Tab. Primaquine 2.5 Mg , Tab. Primaquine 7.5 Mg , Tab. Propranolol 10 Mg , Tab. Pyridoxine 10 Mg , Tab. Pyridoxine 100 Mg , Tab. Pyridoxine 40 Mg , Tab. Quinine 300 Mg , Tab. Rabeprazole 20 Mg , Tab. Ramipril 2.5 Mg , Tab. Ranitidine 150 Mg , Tab. Ranitidine, Dicyclomine (150+10Mg) , Tab. Ranitidine, Domperidone (150+10Mg) , Tab. Riboflavin 5 Mg7 , Tab. Risperidone 2 Mg , Tab. Salbutamol 4 Mg , Tab. Seratiopeptidase + Diclofenace Pottasium 10+50Mg , Tab. Sitagliptin 50 Mg , Tab. Sodium Valproate 500 Mg , Tab. Sorafenib 200Mg , Tab. Spironolactone 25 Mg , Tab. Sucralfate 20 Mg , Tab. Sulfamethoxazole And Trimethoprim800mg +160Mg , Tab. Sulfamethoxazole+ Trimethoprim (Pediatric S) 400 Mg+80 Mg , Tab. Sulfamethoxazole+Trimethoprim200mg +40 Mg , Tab. Sulfamethoxazole 100Mg And Trimethoprim 20Mg , Tab. Sulfasalazine 500 Mg , Tab. Sulfadoxine 500Mg + Pyrimethamine 25Mg , Tab. Sumatriptan 25 Mg , Tab. Sunitinib/Capsule50 Mg , Tab. Tamoxifen 10 Mg3 , Tab. Tamoxifen20 Mg , Tab. Tapentadol 100 Mg , Tab. Telmisartan 40 Mg , Tab. Temozolamide 250 Mg , Tab. Thiamine 100 Mg7 , Tab. Thinylestradiol (A) + Levonorgestrel (B) 0.03 Mg (A) + 0.15 Mg (B) With Ferrous , Tab. Tinidazole 300 Mg , Tab. Tramadol 50Mg , Tab. Traexamic Acid 500 Mg And Mefenmic Acid 250Mg , Tab. Tranexamic Acid 500Mg , Tab. Trihexyphenidyl 2 Mg , Tab. Tolperisone Hydrochloride 150 Mg , Tab. Verapamil 40 Mg , Tab. Vincristin1 Mg , Tab. Vartin 16 , Tab. Vitamin. B Complex Nfi (Prophylactic) B1 2 Mg, B2 2Mg, B6 0.5 Mg, Niacinamide 25 Mg, Calcium Pantothenate 1 Mg , Tab. Warfarin 1 Mg , Tab. Warfarin 2 Mg , Tab. Warfarin 5 Mg , Tab. Zinc Sulphate Dispersible 10Mg , Tab. Zinc Sulphate Dispersible 20Mg10 X 10 , Tab. Zoledronic Acid4 Mg , Tab. Zolpidem10 Mg , Cap. Amoxycillin 250 Mg10 X 10 , Cap. Amoxycillin 500 Mg10 X 10 , Cap. Ampicillin 500 Mg10 X 10 , Cap. Camphor 25Mg, Chlorathymol 5Mg, Eucalyptol 125Mg, Menthol 65 Mg & Terpinrecol 120 Mg , Cap. Cephalexin 250 Mg10 X 10 , Cap. Clindamycin 150 Mg10 X 10 , Cap. Cloxacillin 125 Mg10 X 10 , Cap. Cloxacillin 500 Mg10 X 10 , Cap. Cholecalciferol Usp 60000 Iu , Cap. Cycloserine 125 Mg10 X 10 , Cap. Doxycycline 100Mg10x10 , Cap. Flupirtine Maleate 100 Mg , Cap. Hydroxyurea 500 Mg , Cap. Nifedipine 5 Mg10 X 10 , Cap. Pomalidomide 2 Mg , Cap. Rifampicin 150Mg , Cap. Rifampicin 300Mg , Cap. Rifampicin 450Mg , Cap. Rifampicin 600Mg , Inj. Acyclovirinj 250 Mg/Vialvial , Inj. Adenosineinj 3 Mg/ Ml -2 Ml Amp , Inj. Adrenalineinj 1 Mg/ Ml1 Ml Amp , Inj. Amikacininj 100 Mg/2 Ml2 Ml Vial , Inj. Amikacininj 500 Mg/2 Ml Vial2 Ml Vial , Inj. Aminophylline Inj 25 Mg/ Ml10 Ml Vial , Inj. Amiodaroneinj 50 Mg/ Ml3 Ml Amp , Inj. Amoxycillin+Clavulanic Acid (Amoxycillin 500 + Clavulanic Acid 100 Mg)/ , Inj. Amphotericin B 50 Mgvial/Ampoules , Inj. Ampicillininj 500 Mg/Vialvial , Inj. Anti D Immunoglobulin For Iv/Im Use (Monoclonal)Inj 150Mcg1 Ml Vial , Inj. Anti D Immunoglobulin For Iv/Im Use (Monoclonal)Inj 300Mcgpfs/Vial , Inj. Anti Snake Venominj Polyvalent 10 Ml (Lyophilized)10 Ml Vial , Inj. Antitetanus Immunoglobulinsinj 250 Iu/Vialvial , Inj. Artesunateinj 60 Mg /Vialvial , Inj. Artesunatepowder For Injection 120 Mg , Inj. Atracurium 10 Mg/ Ml2.5 Ml Amp , Inj. Atropine 0.6 Mg/ Ml2 Ml Amp , Inj. Bendamustineinj 100 Mg , Inj. Benzathine Penicilline12 Lakh Iu/Vialvial , Inj. Benzathine Penicilline6 Lakh Iu/Vialvial , Inj. Betamethasone 4 Mg/Ml1 Ml Amp , Inj. Betamethasone Sodium Phosphateinj 4 Mg/ Ml1 Ml Amp , Inj. Biphasic Isophane Insulininsulin Biphasic Aspart 30:70 100 Iu/Ml (Firm Has To Supply Compatible Pen Along With Cartridges As And When Required Without Any , Inj. Bleomycininj 15 Mg , Inj. Bortezomib 2 Mg , Inj. Bupivacaine Hcl 0.5% 20 Ml Vial , Inj. Caffeine Citrateinj 20 Mg/ Ml3 Ml Vial , Inj. Calcium Gluconateinj 10%10 Ml Vial , Inj. Carboprost (15-Methyl Pgf2a)Inj 250Mcg1 Ml Amp , Inj. Cefotaximeinj 1Gm/Vialvial , Inj. Cefotaximeinj 250 Mg/Vialvial , Inj. Cefotaximeinj 500 Mg/Vialvial , Inj. Ceftazidimepowder For Injection 1Gm , Inj. Ceftazidimepowder For Injection 250 Mg , Inj. Ceftriaxoneinj 1 Gm/Vialvial , Inj. Ceftriaxoneinj 250 Mg/Vialvial , Inj. Ceftriaxoneinj 500 Mg/Vialvial , Inj. Chloroquineinj 40 Mg/ Ml5 Ml Amp , Inj. Chlorpheniramineinj 10 Mg/ Ml10 Ml Vial , Inj. Ciprofloxacininj 200 Mg/100 Ml100 Ml Ffs Bottle , Inj. D-10 (Dextrose 10%)Iv Fluid (Dextrose 10%)500 Ml Ffs Bottle , Inj. D-25 Injection (Dextrose)Iv Fluid (Dextrose 25%)100 Ml Bottle , Inj. D-25 Injection (Dextrose)Iv Fluid (Dextrose 25%)500 Ml Bottle , Inj. Decarbazine 200 Mg10 Mg /Ml , Inj. Desferrioxamineinjection 500 Mgvial , Inj. Dexamethasoneinj 8 Mg/2 Ml2 Ml Vial , Inj. Dextrose 5%Iv Fluid(Dextrose 5%)500 Ml Ffs Bottle , Inj. Dextrose With Salinei/V Fluid (Dextrose 5% + Saline 0.9%)500 Ml Ffs Bottle , Inj. Diazepam 5 Mg/ Ml2 Ml Amp , Inj. Diclofenac 25 Mg/ Ml3 Ml Amp , Inj. Dicyclomine Hydrochloride 10 Mg/ Ml2 Ml Amp , Inj. Diltiazeminjection 5 Mg/Ml , Inj. Dobutamineinj 50 Mg/ Ml5 Ml Amp , Inj. Dopamineinj 40 Mg/ Ml5 Ml Amp , Inj. Doxorubicininj 50 Mg , Inj. Drotaverine 40 Mg/2 Ml2 Ml Amp , Inj. Drotaverineinj 40 Mg/2 Ml2 Ml Amp , Inj. Duvadilan 5Mgvial , Inj. Enoxaparin Inj 40 Mg Equivalent To-4000 Iuvial/Pfs , Inj. Erythropoietininjection 10000 Iu/Ml , Inj. Erythropoietininjection 2000 Iu/Ml , Inj. Esmolol 10 Mg/Ml , Inj. Etophylline +Theophylline 220 Mg/2 Ml (169.4+50.6 Mg)2 Ml Amp , Inj. Ferric Carboxymaltose50mg/Ml20 Ml Vial , Inj. Fluphenazineinjection 25Mg1ml Vial/ Ampoules , Inj. Fulvestrantinj 500 Mg , Inj. Furusemideinj 10 Mg/ Ml2 Ml Amp , Inj. Gentamicininj 40 Mg/ Ml2 Ml Amp , Inj. Glucose (A) + Sodium Chloride (B)Injection 5% (A) + 0.9% (B)500Ml Ffs , Inj. Glycopyrolate 0.2 Mg/ Ml1 Ml Amp , Inj. Haloperidolinj 5 Mg/ Ml1 Ml Amp , Inj. Heparin Inj 1000 Iu5 Ml Vial , Inj. Hepatitis B Immunoglobulin100 Iu/Vialvial , Inj. Human Chorionic Gonadotropininjection 10000 Iuvial Of 1 Ml Injection , Inj. Human Chorionic Gonadotropininjection 5000 Iuvial Of 2 Ml Injection , Inj. Hyaluronidase 1500Iu , Inj. Hydrocortisoneinj 100 Mg/Vialdry Powder 100Mg/Vial , Inj. Hydroxy Propymethyl Cellulose 2% Prefilled Syringe 3Ml , Inj. Hydroxyethyl(6% Saline Solution For Infusion)Starch 6%Ip , Inj. Hyoscine Butylbromide20mg /Ml1 Ml Vial/Amp , Inj. Ifosfamideinj 1 Gm , Inj. Inj. Deferoxamine500mg/Vial , Inj. Insulin Solubleinj 40 Iu/ Ml10 Ml Vial , Inj. Irinotecaninj 100 Mg , Inj. Iron Sucroseinj 100 Mg/5 Ml5 Ml Amp , Inj. Iv Human Immunoglobin 5% Iv Ig(5Mg/100Ml Each), , Inj. Ketamine 10 Mg/ Ml10 Ml Vial , Inj. Labetalolinj 20 Mg/4 Ml4 Ml Amp , Inj. Labetalolinjection 5 Mg/Ml , Inj. Lignocaine 2% 30 Ml Vial , Inj. Lignocaine+Adrenaline 2% + 0.005 Mg/ Ml30 Ml Vial , Inj. Lorazepaminj 2 Mg/ Ml1 Ml Vial , Inj. Magnesium Sulphate 500 Mg/Ml , Inj. Mannitolinj 20%100 Ml Ffsbottle / 350 Ml Ffs Bottle , Inj. Medroxy- Progesteroneacetateinjection 150 Mg1 Ml / Vial , Inj. Mephentermine 30 Ml Vial Mg/Ml10 Ml Vial , Inj. Meropenem500 Mgvial , Inj. Methyl Ergometrine Maleate 0.2 Mg/ Ml1 Ml Amp , Inj. Methylprednisoloneinjection 1000 Mg/Mlvial , Inj. Methylprednisoloneinjection 500 Mgvial Of 4 Ml , Inj. Metoclopramideinj 5 Mg/ Ml2 Ml Amp , Inj. Metronidazole 500 Mg/100 Ml100 Ml Ffs Bottle , Inj. Midazolam 1 Mg/ Ml 5 Ml Amp/ 10Ml Vial , Inj. Morphine 10 Mg/ Ml1 Ml Amp , Inj. Morphineinjection 15 Mg/Mlvial , Inj. Naloxoneinj 0.4 Mg/ Ml1 Ml Amp , Inj. Neostigmine 0.5 Mg/ Ml1 Ml Amp , Inj. Nitroglycerine (Glyceryl Tri Nitrate)Inj 25 Mg/5 Ml5 Ml Amp , Inj. Noradrenalineinj 2 Mg Base/2 Ml Amp.2 Ml Amp , Inj. Ondansetroninj 2 Mg/ Ml2 Ml Amp , Inj. Oxytocin Injection 5Iu/Mlinjection 5 Iu/Ml1 Ml Ampule , Inj. Pantoprazoleinj 40 Mg/Vialvial , Inj. Paracetamol150 Mg/ Ml2 Ml Amp , Inj. Pemetrexedinj 500 Mg , Inj. Pentazocine 30Mg/Ml1 Ml Ampule , Inj. Pheniramineinjection 22.75 Mg/Ml2 Ml Vial , Inj. Phenobarbitoneinj 200 Mg1 Ml Amp , Inj. Phenytoininj 50 Mg/ Ml2 Ml Amp , Inj. Phytomenadione 10 Mg/Ml10 Mg Ampule , Inj. Pioglitazone15mg , Inj. Piperacillin +Tazobactam 4.5 Gm/Vialvial , Inj. Pralidoxime (Pam)Inj 25 Mg/ Ml20 Ml Amp , Inj. Premix Insulin30:70 Injection (Regular:Nph)2 , Inj. Premix Insulin30:70 Injection 40 Iu/Ml , Inj. Promethazine 10 Mg/Mlone Injection 1 Vial , Inj. Promethazine 50 Mg (25Mg/ Ml)2Ml Vial/Ampoules , Inj. Propofal 10 Mg/Ml1 Ml /Vial , Inj. Protamine 50 Mg/5 Ml , Inj. Quinineinj 300 Mg/ Ml2 Ml Amp , Inj. Rabies Immunoglobulin300 Iu/2 Ml2 Ml Vial , Inj. Rabies Vaccine (Cell Culture) Id/Iminj 2.5 Iu/ Ml1 Ml Vial , Inj. Ranitidineinj 50 Mg/2 Ml2 Ml Amp , Inj. Ringer Lactatei/V 0.24 % V/V Of Lactic Acid ( Eq. To 0.32% W/V Of Sodium Lactate), 0.6 % W/V Sodiumloride, 0.04 % W/V Potassium Chloride And 0.027 % , Inj. Risperidone 50 Mgvial Of 2 Ml , Inj. Rituximabinj 500 Mg , Inj. Sodium Bicarbonate Inj7.5% W/V10 Ml Amp , Inj. Sodium Chloride - Hypotonicinj N/2(0.45%)500 Ml Ffs Bottle , Inj. Sodium Chloride - Isotonicinj 0.9% Isotonic(Equivalent To Na+154 M Mol/L, Cl+154 M Mol/L)100 Ml Ffs , Inj. Sodium Chloride - Isotonicinj 0.9% Isotonic(Equivalent To Na+154 M Mol/L, Cl+154 M Mol/L)500 Ml Ffs , Inj. Streptokinaseinjection 15 Lac/Vialvial , Inj. Succinyl Choline 50 Mg/ Ml10 Ml Vial , Inj. Surfactant Suspension 25 Mg/Ml100 Ml Vial , Inj. Thiamineinjection 100 Mg/Ml1 Ml/Vial , Inj. Thiopentone 0.5Gm Powder/Vial20 Ml Vial , Inj. Topotecaninj 4 Mg , Inj. Tramadol 50 Mg/ Ml2 Ml Amp , Inj. Tranexamic Acid 500 Mg/5 Ml.5 Ml Amp , Inj. Trastuzumabinj 440 Mg , Inj. Urokinase(5 Laciu)Vial , Inj. Vancomycinpowder For 1 G , Inj. Vancomycinpowder For Injection 250 Mg , Inj. Vancomycinpowder For Injection 500 Mg , Inj. Vecuronium 2 Mg/ Ml2 Ml Amp , Inj. Verapamil 5 Mg/2 Ml , Inj. Vinblastininj 10 Mg , Inj. Vinorelbineinj 10 Mg , Inj. Vitamin B12 ,Injection500 Mcg/Ml(30 Ml Amp/ Vial) , Inj. Vitamin K11 Mg/0.5 Ml0.5 Ml Amp , Inj. Water For 2 Ml Amp , Inj. Water For 5 Ml Amp , Drops Atropine1% Eye Drops5 Ml Vial , Drops Boro-Spirit Ear Drops-0.183 Gm Boric Acid In 2.08 Ml Of Alcohol , Drops Carboxy Methyl Celluslose 10 Ml , Drops Carboxymethyl-Cellulosedrops 0.5%10 Ml/Vial , Drops Ciprofloxacineye / Ear Drop 0.3%5 Ml Vial , Drops Combo Ear Drop- Chloramphenicol 5% W/V+Clotrimazole 1%+Lignocainehydrochloride 2%Combo Ear Drop- Chloramphenicol 5% , Drops Dexamethasonedrop(0.1%, 5Ml),Eye 5Ml Eye Drop , Drops Fluconazoleeye3 Mg/Ml(10 Mlvial),Eye Drop10 Ml , Drops Gentamicin Ear(0.3%)5 Ml Vial , Drops Homatropine 2% 5Ml , Drops Hydroxypropyl Methyl Cellulose 0.3% W/V Eye 10Ml , Drops Lantanoprost0.005%(5Ml),Eye 5Ml , Drops Moxifloxacin0.5% W/V(5 Ml),Eye 5Ml , Drops Normal Salinenasal Drops: Sodium Chloride Drops 0.05% W/V , Drops Ofloxacin 0.3% + Dexamethosne + Na Phosphate 0.1% Eye 5Ml , Drops Paracetamol- 125Mg/Ml15 Ml Bottle With Dropper , Drops Phenylephrine Hcl 5% + Tropicamide 0.8% Eye 5Ml , Drops Pilocarpine 4%5 Ml Bottel , Drops Pilocarpinedrops 1%5 Ml Bottel , Drops Pilocarpinedrops 2%5 Ml Bottel , Drops Povidone Iodine 1% (Septidine) Eye 10Ml , Drops Prednisolonedrops 1%10 Ml Bottel , Drops Sodium Aminosalicylate Granules10 Gm , Drops Timolol0.5% Eye Drops5 Ml Vial , Drops Tobramycin 0.3% Eye 5Ml , Drops Tropicamidedrops 1%5 Ml Drop , Drops Wax Solvent Ear Benzocaine2.7% W/V10 Ml Bottel Drop , Drops Wax Solvent Ear Drops: Paradichloro- Benzene2 % W/V10 Ml Bottel , Drops Xylometazolinenasal Drops 0.05 %, , Drops Xylometazolinenasal Drops: Adult (0.1%) , Inhaler Halothane 250 Ml Bottle , Inhaler Isoflurane 250 Ml Bottle , Inhaler Ipratropium Inhalation (Mdi/Dpi)20 Mcg/Dose Ipratropium Respirator Solution , Inhaler Tiotropium Inhalation(Dpi) 18 Mcg/Dose , Inhaler Tiotropium Inhalation(Dpi) 9 Mcg/Dose , Inhaler Salbutamol Inhaler 100Mcg/Dosemetered Dose Container , Ointment Hydrocortisone 0.5% , Ointment Hydrocortisone 1% , Ointment Povidone Iodine5% Ointment15 Gram Tube , Ointment Acyclovir3% -5Gm Tube , Ointment Gum Paint Tannic Acid 2% , Ointment Betamethasone 0.05% 15 Gm , Ointment Aceclofenac + Linsed Oil + Methyl Salicylate + Menthol 30Gm , Syp. Dextromethorphan 10Mg/5Ml 50 Ml , Syp. Dextromethorphan 10Mg/5Ml 100Ml Pack Bottle , Syp. Albendazole200mg/5 Ml10 Ml Bottle , Syp. Ambroxol Hcl 15Mg + Terbutaline Sulphate 1.25Mg + Guaiphenesin 50Mg 5Ml ((Additional Composition Of Menthol Also Acceptable) 100Ml Bottle), Syrup , Syp. Ambroxol Hcl 15Mg + Terbutaline Sulphate 1.25Mg + Guaiphenesin 50Mg , Syp. Ambroxol 30Mg, Salbutamol 2Mg, Guaiphenesin 50Mg/5Ml, 100Ml , Syp. Amoxycillin+Clavulanic Acid (Amoxicillin 200Mg+ Clavulanic Acid , Syp. Amoxycillin 125Mg + Clavulanate Pot.31.25Mg Dry Syrup (30Ml) , Syp. Azithromycin Suspension 100Mg/5Ml 15Ml , Syp. Azithromycinsyp 200Mg/5Ml15 Ml Bottle , Syp. B-Complex (Nfi Foumula) Vit.B1 2Mg, Vit.B2 2Mg, Vit.B6 0.5Mg, Niacinamide 25Mg, Calcium Pantothenate 1Mg 100Ml , Syp. Bromhaxine Hcl 8Mg + Trebutaline 2.5Mg/5Ml Syrup (50Ml) , Syp. Bromhexine Hcl 4Mg, Guaiphenesin 50Mg, Terbutaline Sulphate 1.2Mg/5Ml 100Ml , Syp. Bromhexine Syp 4Mg/5Ml50 Ml Bottle , Syp. Caffeine Oral Liquid 20 Mg/Ml , Syp. Carbamazepine Oral Liquid 100 Mg/5 Ml , Syp. Cefixime + Clavunate 50+31.25Mg , Syp. Cefiximeoral Suspension 100Mg/5Ml10 Ml Bottle , Syp. Cefpodoxime + Clavunate 30Ml , Syp. Cephalexinsyp 125Mg/5Ml30 Ml Bottle , Syp. Cetirizinesyp 5Mg/5Ml30 Ml Bottle , Syp. Cetrizine Hcl 5Mg, Ambroxol Hcl 30Mg/5Ml, 60Ml Syrup , Syp. Chloroquinesyp 160Mg /10Ml(50Mg/5Ml Base)60 Ml Bottle , Syp. Chlorpheniramine Maleate (Paracetamol 125Mg + Phenylpherine 5Mg + Cpm 0.5Mg + Sodiym Citrate 60Mg + Menthol 1Mg) , Syp. Codeineoral Solution 15 Mg/5 Ml60 Ml Bottle , Syp. Diphenhydramine 100Ml , Syp. Diethylcarbamazine Oral Liquid 120 Mg/5 Ml , Syp. Domperidone1mg Per 1Ml Suspension30 Ml Bottle , Syp. Doxycyclinedry50 Mg/5 Ml , Syp. Etiophylline And Theophylline Paediatric Syrup. (100Ml Bottle) , Syp. Furazolidone 25Mg + Metronidazole Benzoate 100Mg/5Ml 60Ml Syrup , Syp. Gum Paint (Tannic Acid)2% W/V15 Ml Bottle , Syp. Haemoglobin 2.09G, Ferric Ammo Cit125mg, Vitb1, 17.5Mcg, Folic Acid 0.5Mg, Alchol0.87Ml (5.5%V/V) Per 15Ml, 200Ml (Syrup) , Syp. Hydroxyzine 10 Mg/5 Ml , Syp. Iron & Folic Acidsyp Iron Each 1 Ml Contains 20Mg Elemental Iron+Folic Acid , Syp. Lactulosesolution 10 Gm /15 Ml100 Ml Bottle , Syp. Levosalbutamol50mcg/Dose , Syp. Levosulbutamol 100 Mcg , Syp. Metronidazoleoral Suspension 200 Mg/5Ml60 Ml Bottle , Syp. Montelukast Syrup60 Ml Bottle , Syp. Multivitamin With Protein 200 Ml , Syp. Drop Multi Vitamin (Appro. 22 Drops) Each Ml Contains Vitamin A Ip 3000 Iu 1Mg, Riboflavine Phosphate Sodium Ip 2Mg, D Panthenol Ip 2.5Mg Miacinamide Ip 10Mg Pyridoxine Ip 1Mg Cyanocoblamine Ip 1Mg Lagine Hcl Usp 10Mg , Syp. Ofloxacin + Tinidazole (50+100Mg), 30Ml Syrup , Syp. Ondansetronsyp 2Mg/5 Ml30 Ml Bottle , Syp. Paracetamol 125Mg/5 Ml60 Ml Bottle , Syp. Pediatric Solution Like Isolyte P, N/2 & N/5Pediatric Solution Like Isolyte P, N/2 , Syp. Potassium Chloride Oral Solution 100Mg/Ml200 Ml Bottle , Syp. Potesium Chloride Oral Solution 200Ml Bottle Each 15Ml Postsium Chloride Ip 100Mg , Syp. Promethazinesyp 5Mg/ 5Ml60 Ml Bottle , Syp. Salbutamol 1Mg, Theophylline 50Mg, Bromhexine 4Mg, Per 5Ml (100Ml Syrup) , Syp. Salbutamol 2Mg + Guaiphenesin 100Mg + Bromhexine Hcl 4Mg/Ml Syrup. (50Ml) , Syp. Salbutamol Syp 2Mg/5Ml60 Ml Bottle , Syp. Sodium Valproate Each 5Ml Contains 200Mg200 Ml Bottle , Syp. Sucralfate 1Gm/5Ml100ml Bottle , Syp. Sulfamethoxazole+Trimethoprimoral Liquid ( 200Mg + 40 Mg) / 5 Ml50 Ml Bottle , Syp. Vitamin A 100000 Iu/Ml With Marked Spoon For 1Ml &2Ml100 Ml Bottle , Syp. Zinc Sulphate Syrup 20Mg/5Ml (100Ml) , Tube Atropine1% Eye Ointment3 Gram , Tube Atropinesulphate 1%, , 3 Gm , Tube Benzoyl Peroxidegel 5% , Tube Betamethasone Dipropionateointment 0.05%15 Gram , Tube Chloramphenicoleye Ointment 0.5%4G/5G , Tube Ciprofloxacineye Ointment 0.3%3/3.5 Gram , Tube Clotrimazole Cream2%W/W15 Gram , Tube Diclofenac 0.01 , Tube Diclofanac Diethylamine, Linseed Oil, Methyl Salicylate & Menthol 30 Gm Gel , Tube Duvadilan10 Mg10x50 , Tube Framycetin Sulphate1% Cream30 Gram , Tube Fusidic Acidcream/Ointment 2%5 Gram , Tube Ketoconazole, Neomycin, Iodochlorhydroxyquinoline, Tolnaftate, Chobetasol Propionate 15 Gm Gel , Tube Lignocaine 2% 30 Gram , Tube Miconazolecream 2% W/W15 Gram , Tube Mupirocincream/Ointment 2%5 Gram , Tube Povidine-Iodine Germicidegargle 20% W/V , Tube Salicylic Acidointment 6% 30 Gm , Tube Silver Sulphadiazine Cream Usp 1% 25 Gram , Combo Pack Artesunate + Sulphadoxine + Pyrimethamine (Age Group 15 Or Above)Tab Artesunate 200 Mg(3Tab) + Sulphadoxine 750 Mg(2Tablets) + Pyrimethamine , Combo Pack Artesunate + Sulphadoxine + Pyrimethamine (Age Group 9 To 14 Years)Tab Artesunate 150Mg (3Tab)+ Sulphadoxine 500Mg (2 Tab)+Pyrimethamine 25Mg , Combo Pack Artesunate + Sulphadoxine + Pyrimethamine(Age Group Between 1-4 Years)Tab Artesunate 50 Mg (3 Tab) + Sulphadoxine 500 Mg(1 Tab) + Pyrimethamine 25 Mg , Combo Pack Combi-Pack With Mifepristone + Misoprostol(1 Tablet Of Mifepristone 200 Mg And 4 Tablets Of Misoprostol 200Mcg)Combi Pack , Ampule Budesonide Nebulising Suspension Containing Budesonide 0.5 Mg/2 Ml2 Ml , Jelly Glycerin Oral Liquid , Gel Choline Salicylate Lignocaine Hcl With Benzalkonium Chloride Gel 15Gm , Oral Suspension Amoxycillin125 Mg/5 Ml30 Ml Bottle , Oral Suspension Chlorpheniramineoral Liquid 2 Mg/5 Ml , Oral Suspension Ibuprofen 100Mg/5Ml60 Ml Bottle , Oral Suspension Rehydration Salts Ip 4.4Gm (Sodium 75, Potassium 20, Chloride 6, Citrate10, Dextrose 75) , Oral Suspension Valproateoral Solution 200Mg/5Ml100 Ml Bottle , Powder Bleaching Powder Containing Not Less Than 30% W/W Of Available Chlorine (As Per I.P)Containing Not Less Than 30% W/W Of Available Chlorine (As Per I.P) , Powder Glucose Packet 75 Mg For Ogtt Testglucose Packet 75 Mg For Ogtt , Powder Anti Bacterial Powder, 10 Gm ( Neomycin Sulphate 5 Mg, Baccitracin 250 Unit, Sulphacetamide Sodium 60 Mg) , Powder Reduced Osmolarity Ors Pkt. Who Formulao.R.S. Glucose- 75Meq,Sodium- 75M Eq Or M Mol /L,Chloride - 65Meq Or M Mol/L, Potassium- 20Meq Or M Mol/L , Citrate- 10M Mol/L Osmolarity -245M Osm/L,Dextrose 13.5G/L Sodium Chloride 2.6G/L Potassium , Powder Electrolyte Sachect , Solution Hydrogen Peroxide Solution 6% , Solution Povidone Iodine Solution 5%,100 Ml Bottle , Solution Enema Sodium 100 Ml (Sodium Acid Phosphate 10 Gm, Sodium Phosphate 8 Gm / 100 Ml) With Tube , Solution Eosin 2% Solution (1X250 Ml),Consumable , Solution Ethanol (Abosolute Alcohol 99.9% (500Ml) , A.C. 1 Ton Split 3 Star , A.C. 1.5 Ton Split 3 Star , A.C. 2 Ton Split 3 Star , A.C. Window 1.5 Ton 3 Star , A.C. Window 2 Ton 3 Star , Abdominal Belt(32 Inch Each), , Abdominal Belt(34 Inch Each), , Abdominal Belt(36 Inch Each), , Abdominal Belt(38 Inch Each), , Absolute Alcohol (Ethanol)(1X500 Ml = 500 Ml), , Absorbable Gelatine Sponge Ip 80Mm X 50Mm X 10Mm , Absorbent Cotton Roll 100 Gm , Absorbent Cotton Wool Ip 500 Grms (Roll), , Acetic Acid - Solution(3% 100 Ml Bottle), , Acetone Detection Kit , Acralic Board (Saineaj Board Acralic Sheet) , Adesive Lable For Sputam Container , Adhesive Plastcloth Based Usp 7.5 Cm X 5 Mts/Roll , Adhesive Plast Cloth Based 1 Inch X 5 M / Roll , Adhesive Tape 7.5Cm X10 (Mtr/Roll), Cloth Based , Adult Brief Daiper Set- Made Of Ultra Absorbent Material With Leakage Barrier & Having Soft, Flexible Leg Elastic. With Wetness Indicator. Made Up Of Woodpulp, Sap, Absorbent Nonwooven Fabric. The Set Contatin Two Pcs Of Medium Daiper {Nominal Size 81Cm-111Cm} For Waist Size 31-44 & Three Pcs Of Large Daiper {Normal Size 85Cm-128Cm} For Waist Size 34-50 , Ahg Sera 5Ml(Each), Coombs , Alchlol Absouite 500Ml (Ethanol) 99.9% , Alcohal Based Hand Sanitizer(500Ml Bottle With Dispenser), , Alkaline Phosphate(100 Ml (5 X 20)), , All Human (Bovine Aprotinin Free) Fibrin Sealant(1 Ml), , All Human (Bovine Aprotinin Free) Fibrin Sealant(2 Ml), , All Out Machine With Refill , All Out Refill , Almeera (Cr Sheet 1.00 Mm) Size 1675X840x480 Mm (Iron) , Almeera (Cr Sheet 1.00 Mm) Size 1980X915x480 Mm (Iron) , Almeera Full Size (78X3619) Sheet Gauge 20 (Iron) , Almehra Iron 6X3x1.5”, 22 Gauge , Aluminium Bartan , Ambu Bag / Adult Each -1700Ml, With Oxygen Connecting Tube ,Should Be Supplied With A Carry Pouch , Ambu Bag Should Be Complete With Required Autoclavable Valves And Other Accessories,(Should Have Silicon Rubber Bellow To Withstand Autoclave At 134 Deg.C), , Ambu Bag / Resuscitator Silicon 200-250 Ml Infant Size-Each, With Oxygen Connecting Tube ,Should Be Supplied With A Carry Pouch , Ambu Bag Should Be Complete With Required Autoclavable Valves And Other Accessories,(Should Have Silicon Rubber Bellow To Withstand Autoclave At 134 Deg.C) Should Be Multiple Times Autoclavable), , Ammonium Sulphate (Analar (Gr/Ar) (1X500 Gm = 500Gm), , Anc Table 6X2.5X3 Of Iron (Lxwxh) , Anteriar Veginal Wall Retractor , Anti A Sera Igm(10 Vial), , Anti Abd Grouping Serum 3X10ml , Anti B Sera Igm(10 Vial), , Anti Malaria Larva Oil Harbal Based 5 Litter Can , Anti-D (Polyvalent)(1X10 Ml), , Antiseptic Concentrate For Floor Clening Pack Of 5 Litter Can , Ast/Got 600 Ml , Attandent Bed Powder Coted 72Lx30Wx24H , Auramine O , Auto Clave (Poratable) Single Drum Aluminum Seamless Construction Made Of Albminium Alloy With Turning On Lid Highly Polished. It Comes With One Stop Cock (Continus Bleeding Valve) Safety Valve And Pressure Guage Size 12X12X12X20 , Auto Cleanser For Cbc Machine(2 Liter), , Auto Dill Solution For Cbc Machine(20 Liter), , Auto Lyser Solution For Cbc Machine(500Ml), , Auto Pippets Fixed Volume 10 Micro Liters Each Syring , Auto Pippets Fixed Volume 1000 Micro Liters Eachsyring , Auto Pippets Fixed Volume 20 Micro Liters Each , Autoclave Cooker Type , Autoclave Ss , Double Walled Size (22X12) With Stand (Manual) Isi Marked , Autoclave Ss , Double Walled Size (24X16) With Stand (Manual)Isi Marked , Autoclave Ss , Electric Operated Size (14X12)With Stand , Autoclave Ss , Electric Operated Size (20X12) With Stand , Autoclave Ss , Eletric Operated Size (22X12)With Stand , Autoclave Vertical , B.B Silk Size-3/0 (12 Foils/Pkt)(3/8Cir Rcut Needle 26Mm Length 76 Cm),Needle , B.B Silk With 1/2 Cir Rb Needle Size:1/0 20 Mm Length 75 Cm Non Absorbable Surgical Sutures Usp Surgical Material , B.B Silk With 1/2 Cir Rb Needle Size:2/0 30 Mm Length 75 Cm Surgical Material , B.B. Silk 6 Reels X 25 Mts Length 25 Mts. Black Braided Silk Without Needle In Reels Non Absorbable Surgical Sutures Usp 3-0(6 Reels Is Per Box Rate Should Be Quoted For 6 Reels), , B.B. Silk 6 Reels X 25 Mts Length 25 Mts.Black Braided Silk Without Needle In Reels Non Absorbable Surgical Sutures Usp-, 2-0(6 Reels Is Per Box Rate Should Be Quoted For 6 Reels ),Surgical Material , B.B. Silk 6 Reels X 25 Mts Size:1/0(6 Reels Is Per Box Rate Should Be Quoted For 6 Reels),Surgical Material , Baby Diapers Small (10 Diaper Per Pkt) Standard Company , Baby Feeding Spoon 1 Ml , Baby Feeding Spoon 2 Ml , Baby Feeding Spoon 5 Ml , Baby Feeding Spoon Feeding Of Milk Steel , Baby Oxygen Maskall Sizes , Baby Towile , Baby Tray Ss 15X18Of Ss With Cover Pack Of Of Ss With Cover , Baby Weigh Machine Capacity 20Kg Resolution : 10 Gm Pan/Platform : 550Mmx300mm (Min) Electronic , Bag For Carrying Kit/Material During Home Visit 2X1.5X1 , Balanced Salt Solution 500 Mlbottle(Each), , Barium Chloride 10% (500 Ml Bottle) , Barraquer Wire Speculum, Large(Num), , Basic Carbol Fuchsin For Afb Staining 25 Gm/Pkt , Basic Fuchine 25Gm (Dye Content 85% To 88%) , Basic Fuchisin(Sep.Chemical Name: Pararosaniline Hydrochloride,Chemical Structure: C20h20c1n3 Mol Wt:337.86, Dye Content: Approx 85%-88% &Dye Content Must Be Mentioned) Colour Metallic Green. , Bathroom Air Freshner Odonil , Battery 70D 26 Rmf For Vehicle , Bed Pan Female With Cover (Made Of Stainless Steel) , Bed Pan Male With Cover (Made Of Stainless Steel) , Bed Side Bench 3X1.5X1.5 Steel , Bedside Locker Standard Size , Bedside Locker Standard Size Ss Top , Bilrubin Total & Direct Auto 3X100ml (Span/Tulip/Erba) , Bio Hazard Labels A4 Size , Bio Hazard Lables , Bio Metric Attance Machin Menul Operated , Bio Metric Attance Machine Online Operated , Biochemistry Control Serum L1 5X5 Ml , Biomedical Waste Collection Plastic Bag(Yellow)(450X450 Mm 55 Micron Pkt Of 100Pcs), , Biomedical Waste Collection Plstic Bag(Black 450X450 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Black 750 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Black 900 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Blue 450X450 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Blue 750 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Blue 900 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Red 450X450 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Red 750 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Red 900 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Yellow 750 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biomedical Waste Collection Plstic Bag(Yellow 900 X 900 Mm 55 Micron Pkt Of 100Pcs) , Biometric Thumb Impression Machine 250 Emp. , Black Gogle For Cataract Patient , Black-Braided Silk With 1/2 Cir Cutting Needle 30Mm Length 75 Cm(1/0 12 Foils/Pkt), , Black-Braided Silk With 1/2 Cir Rb Needle 20 Mm Length 75 Cm 1/0 13 Foils/Pkt , Black-Braided Silk With 1/2 Cir Rb Needle 30 Mm Length 75 Cm 2/0 12 Foils/Pkt , Blanket For Baby , Blankets For Neonates , Bleaching Powder Gr-Ii Is 1065/1989 With Upto Datepacked In 25 Kg Hdpe Bags Isi Marked Stable , Blood Administrations Set Adult , Blood Bag Warmer , Blood Bag With Acd/Cpd Solution (Disposable Sterilised) With Needle(100 Ml),Bag , Blood Bag With Acd/Cpd Solution (Disposable Sterilised) With Needle(350 Ml),Bag , Blood Cell Counter Key(Key), , Blood Grouping Anti Sera A Monoclonal(10 Ml Vial), , Blood Grouping Anti Sera B Monoclonal : Antisera Should Be Transparent With More Than One Year Shelf Life At 2-6 C , It Should Give +++ Agglutination At 1.256 Dilution In 3-4 Sec With B Positive Cells 10 Ml , Blood Grouping Anti Sera D Monoclonal :-Antisera Should Be Transparent With More Than One Year Shelf Life At 2-6 C, It Should Give +++ Agglutination At 1.256 Dilution In 3-4 Sec With D Antigen Positive Cells. 10Ml Vail (Eryclone Anti-D Igm) , Blood Vessel Introducers Needles 16G, Sterilized, Set , Bloting Paper(Paper), , Bone Cutter Small , Bone Gauze Large , Bone Gauze Medium , Bone Gauze Small , Bone Holding Forcep For Femur Bone , Bone Holding Forcep For Humerus Bone , Bone Holding Forcep For Radius Ulna Bone , Bone Punch , Bone Spikes Medium , Bone Spikes Small , Bovine Albumin (22% W/V)(1X5=5 Ml), , Bowelss Size 20 , Bowel Baual Size 8 Powder Coated , Bowel Size 20 Powder Coated , Bp Instrument Cell , Bp Instrument Digital , Bp Instrument Marcury Isi Mark , Broom Stick For Sputum Smear Prepration (8 Inches) , Brown Tap (2 Inches) , Brown Tap (5 Inches) , Bubble Cpap Machine , Bucket Brackets (For Hanging Set Of Single Fire Buckets) With Out Fire Bucket , Bucket Brackets (For Hanging Set Of Three Fire Buckets) With Out Fire Bucket , Burn Cage (Bed Cradle) , Canan India Photocopier Presser Roller , Canulated Reamers For Femur , Canullated Drill Bit For4mm Screws , Canullated Tap For4mm Screws , Capillary Tube 100 Pieces , Capillary Tube Biluribin Pack Of 100 Pieces , Carbol Fuchsin For Zn Stain (500Ml Bottle) , Carbolic Acid (Phenol) - Spc. Chemical Structure C6h50h, Molecular Wt: 94.11, Melting Point : 40 Digree C 2,Purity : 99.5% , Carbondioxide Gas In Medium Size Cylinder(B Type),Miscellaneous , Carbondioxide Gas In Small Size Cylinder(A Type),Miscellaneous , C-Arm Macchine , Cartage Brother Printer 1580 Mf New , Cartage Canan 2006N Photocopier Machine , Cartage Canon Printer Hl 6230/6240 New , Cartage Durm , Cartage Hp Printer 05A New , Cartage Hp Printer 12A New , Cartage Hp Printer 16A New , Cartage Hp Printer 49 A New , Cartage Hp Printer 88A New , Cartage Samsung Printer Ml2010 New , Cartain Complete(Plasic With Ring And Stiching) Standrd , Cassette (14X17), For X-Ray , Cassette (8X10), For X-Ray , Catgut Chromic (12 Foils/Pkt)(Size:1/0 Length 150 Cm), , Catgut Chromic Size:2/0 Length 150 Cm , Catgut Chromic With 1/2 Cir Rb Needle 30 Mm Length 70Cm No. 1 -0, 12 Foils Per Packet , Catgut Chromic With 1/2 Cir Rb Needle 40 Mm Length 75Cm No. 1-0, 12 Foils Per Packet , Catgut Chromic With 1/2 Cir Rb Needle 40 Mm Length 75Cm No. 2-0, 12 Foils Per Packet , Catgut Chromic With 1/2 Cir Rb Needle 40 Mm Length 76 Cm (With Needle) ) Absorbable Surgical Sutures Usp,(Size 1, 12 Foils/Pkt),Surgical Material , Catgut Chromic With 1/2 Cir Rb Needle Size:1/0, 30 Mm Length 76Cm Absorbable Surgical Suture Surgical Material , Catgut Chromic With Cd Rb Needle 30 Mm Length 76 Cm Size:2/0 Absorbable Surgical Suture Surgical Usp, 12 Foils/Boxmaterial , Catheter Foleys Size 12-2 Way , Catheter Foleys Size 14-2 Way , Catheter Foleys Size 14-3 Way , Catheter Foleys Size 16-2 Way(11 Each), , Catheter Foleys Size 18- 2 Way , Catheter Foleys Size 20-2 Way(12 Each), , Catheter Foleys Size 22-2 Way(13 Each), , Catheter Foleys Size 24-2 Way(14 Each), , Catheter Long Line Silicon, G-24, Fr-2, L-30Cm , Catheter Suctionassorted 10 No/Each , Catheter Suction Assorted 9 No/Each , Catheter Suction Assorted Covering All Sizes 10,12,14,16,18 Disposable , Catheter Suction Sterile(Size Fg 20 (Disposable, Sterile Each) , Catheter Suction Sterile(Size Fg 22 (Disposable, Sterile Each) , Catheter Suction Sterile(Size Fg 6 (Disposable, Sterile Each) , Catheter Umbilical With Leur Lock(Fr-3 To Fr 3.5 , L-40 Cm) , Catheter Umbilical With Luer Lock Stopcock Fr-2, L-40 Cm , Catheter Umbilical With Luer Lock Stopcock Fr-3, L-40 Cm , Catheter Umbilical With Luer Lock Stopcock Fr-4, L-40 Cm , Catheter Umbilical With Luer Lock Stopcock Fr-5, L-40 Cm , Catheters Single Lumen Set Adult(Size - 6F To 8F, Length 13 Cm To 15 Cm, Each), Femoral , Catheters Single Lumen Set Pediatric(Size - 3F To 4F, Length 13 Cm To 15 Cm Or Less), Femoral , Catheters Single Lumen Size Adult Femoral , Catheters Single Lumen Size Size Pediatrics Femoral , Cathetor Tray Ss With Cover 16X3 , Cbnat Machine , Cc Camera 1/4 Ccd, 3.6 Mm Board Lens 380 Tvl 2 Lux Color Plastic/Dust Proof Metal Body Camera 2 Way Audio. Make;- Impex/Sparsh/ Grovers/Hinum/Vantage/Alpha/Vision. Model:-Cc-31/Bma-231/Hevs-209-3G/Hl110/Va-2W380/Al-Col-106/Vaccs 200 , Cc Camera, 1/4 Ccd, 3.6 Mm Board Lens 380 Tvl 2 Lux Color Plastic/Dust Proof Metal Body Camera With Supply. Make;- Impex/Sparsh/ Grovers/Hinum/Vantage/Alpha/Vision. Model:-Cc-30/Bmc-430/Hev 20 01 /Hl109/Va-Ccs-Tvl2380/Al-Col-105A/Vaccs380s , Cc Camera, 1/4 Ccd, 3.6 Mm Board Lens 380 Tvl 2 Lux Color Plastic/Dust Proof Metal Body Camera. Make;- Impex/Sparsh/ Grovers/Hinum/Vantage/Alpha/Vision. Model:- Cc-72/Bmc-429/Dy-3723 Lph/Hl108/Va-Tvl380/Al-Col-104/Vaccs380 , Cc Camera, 10 Channel Mono Chrome Duplex Multiplexer With Osd, Time Date And Alarm Facility, Make:-Impex/Sparsh/ Grovers/ Hinum/Vvantage/Alpha/Visionmodel:-M-41/Mx-16/Cplm-30-3/Hl202mx/Vaad16/Al-Mux- 16B/Vaad 16 , Cc Camera, 10.1 Mega Pixle Cmos Sensor, Integreated Cleaning System, 2.5 Lcd Screen With 230K Pixle,1600 Viewing Angle, High-Precision 9 Point Af System, Picture Style Image Processing Parameters, Digic Ii Image Processor With 0.2 Sec Start Up - (Each) , Cc Camera, 16 Channel Color Digital Video Recorder, 500 Gm Hdd, Full Triplex, Real Time Display (30 Frame Per Second) Make:- Impex/Sparsh/Grovers/Hinum/Vvantage/Alpha/Vision. Model:-Dv-62/Mcd-62/Dvr-29-Hk/Hl205dvr/Va-Hd500/Al-4C/B2616v , Cc Camera, 16 Channel Mono Chrome Duplex Multiplexer With Osd, Time Date And Alarm Facility, Make:-Impex/Sparsh/ Grovers/ Hinum/Vvantage/Alpha/Visionmodel:-M-41/Mx-16/Cplm-30-3/Hl202mx/Vaad16/Al-Mux- 16B/Vaad 16 , Cc Camera, 20 Channel Mono Chrome Duplex Multiplexer With Osd, Time Date And Alarm Facility, Make:-Impex/Sparsh/ Grovers/ Hinum/Vvantage/Alpha/Visionmodel:-M-41/Mx-16/Cplm-30-3/Hl202mx/Vaad16/Al-Mux- 16B/Vaad 16 , Cc Camera, 24 Channel Mono Chrome Duplex Multiplexer With Osd, Time Date And Alarm Facility, Make:-Impex/Sparsh/ Grovers/ Hinum/Vvantage/Alpha/Visionmodel:-M-41/Mx-16/Cplm-30-3/Hl202mx/Vaad16/Al-Mux- 16B/Vaad 16 , Cc Camera, 6 Channel Mono Chrome Duplex Multiplexer With Osd, Time Date And Alarm Facility, Make:-Impex/Sparsh/ Grovers/ Hinum/Vvantage/Alpha/Visionmodel:-M-41/Mx-16/Cplm-30-3/Hl202mx/Vaad16/Al-Mux- 16B/Vaad 16 , Cctv Bullet Camera 2 Mp , Cctv Bullet Camera 4 Mp , Cctv Bullet Camera 6 Mp , Cctv Cable, 3 Core + Coaxialfor 2 Way/Silent Camera, Make:- Impex/Sparsh/Grovers/Hinum/Vvantage/Alpha/Vision/Isi Model:-C-32/Cc-3/Alc-3C/Isi With Fiting , Cctv Camera Fitting Charge Per Point , Cctv Dome Camera 2 Mp , Cctv Dome Camera 4 Mp , Cctv Dome Camera 6 Mp , Cctv Nvr 16 Channel Standard , Cctv Nvr 32 Channel Standard , Cctv Nvr 4 Channel Standard , Cell Clean For 5-Part Hematology Analyser All Model , Cell Pack, Reagent Pack For Cell Counter((Erma And Mindrug) Complete Set), All Instement , Centeral Oxygen Supply For 10 Bedcomplete Fitting , Centeral Oxygen Supply For 30 Bedcomplete Fitting , Centeral Oxygen Supply For 5 Bed Complete Fitting , Central Venous Catheter Kit(Single Lumen),Kit , Cervical Collar/Each-Soft, Medium Sized , Chair Cushion Foam Thickness 3 With Cotton Cover Box Type , Chikungunya Card Test 1 Gg + 1 Gm (25 Test/Kit) , Children Toys 1. ????, ???? ?? ????? ???? ??????-1 2. ???????? ??????-1 3. ???? ?????? ??? ???? ?? ???? ???? ?????????? ??????-1 4. ???-??? -1 5. ?????????? ???-1 (Total 5 Pcs) , Cholestreol Kit Pack Of 10X10ml (Span/Tulip/Erba) , Chromic With Cd.Rb Needle Absorbable Surgical Suture (12 Foils/Pkt)(40 Mm Length 76 Cm Size:1/0),Surgical Material , Cidex – 5Lter (2% Glutaldyhide) , Cidex Tray 10X5x3 , Cidex Tray 17X5x39 , Cidex Tray 26X53 , Cidex Tray 36X5x3 , Citric Acid Analar/Gr/Ar (1X500 Gm = 500Gm), , Coagulometre Single Chanel , Coconut Broom , Coline 500Ml , Collection Vail 2Ml Pack 100 , Collection Vail 5Ml Pack 100 , Colour Vision Chart , Commode Chair Folding A Commode Chair, Known In British English Simply As A Commode, Is A Type Of Chair Used By Someone Who Needs Help Going To The Toilet Due To Illness, Injury Or Disability. A Commode Chair Sometimes Has Wheels To Allow Easy Transport To The Bathroom Or Shower. , Commodetype Of Chair: Foldable Height Adjustable Material: Steel 25 X 19 X 19 Cm , Complete Delivery Kit-1Plastic Desposable Gown (Non Woven Plastic Laminated,Leak Proof)-2(4*4),(2).Disposable Goggles For Protection Of Eyes-2 (Free Size),(3).Face Mask-2 Free Size,(4).Plastic Disposable Cap(Non Woven Plastic Laminated,Leak Proof)(1Pair,(5).Long Gloves Elbow Length-2Pairs(6 1/2 And 7),(6)Disposable Shoe Covers,Till Calf(Plastic)-2Pair(Free Size)As Per Attached Specification), [987797] , Computer Chair , Computer Table (Size 4X2.6) With All The Fitting Of Parts , Computer Table 4’X2’ With All Fitting Of Parts , Cooler Size-21X19X36Isi Mark 16 Fan & Pump With Gi Sheet Body , Coombs Ahg Sera 5Ml(Each),Consumable , Corneal Knife Tooke (Num), , Corrugated Drainage Sheet, Sterile, Multichannel, Single Use(2 Inch X 6 Inch (Pvc)-Piece), , Cpap Machine , Crape Bandage Cotton Based 10Cm X 4M (Box Of 10 Bandages) , Crape Bandage Cotton Based 15Cm X 4M (Box Of 10 Bandages) , Crash Cart Emergency , Cresent Knife(1 Each), , Cresent Sics Blade (15 Degree) , Crp Test Kit (Latex/Card) (25 Test/Kit) , Currete Straight , Curtain Complete Cloth Silk With Ring And Sticky Stad. Size , Curved Scissors- Laparoscopic 5Mm Size, 360 Degree Rotating With Insulated Shaft, Non Ratchet , Plastic Grip(36 Cms Length, Monopolar Pin Provision For Usage With Electro Surgical Unit, Independently Moving Jaws), , Cvurrete Curved , Cyanemeth Solution For Hb 5 Litre , Cytochrome Stain With Buffer (500 Ml) , Cytoplasam Stain A&B Rapid Pap Pack Of 500Ml , D-Dimer(10X3 Ml), , Deaver Retractor Abdominal Central Oxygen Supply Complete Per Mtr , Defebrillator Biphasic, Features : Offers Variable Energy Level Selection, (2,3,5,7,10,20,30,50,70,100,150,200 Joules), Battery Capacity - 50 Shocks On Single Charge. Adult &Pediatric Paddles Support, Compact & Ligh Weight : Approx 5.0Kgs Max, Ecg Through Paddle , Dengurapid Test Card-Single Test , Dental Air Rotor Burs (Specification- Diamond Point Multilayered Color Banded Shanks -Straight Fissure, Round Number 0,2,4, Inverted Cone Tapered Fissure Edno Access And Endo Z Bur Assorted Bur, Isi/Iso/Ce Marked) , Dental Air Rotor Hand Place Oil Spray (Specification- Imported 500Ml, Isi/Iso/Ce Marked) , Dental Articulating Paper (Specification- 40 Microns Double Sided; Each Pack Contains One Dozen Articulating Paper Book) , Dental Barbed Broaches- Size 21Mm Size: 25Mm (Specification- • Stainless Steel • Handles Should Be Color Coded For Ease Of Identification • Designed For Bulk Removal Of Pulp Tissue • Pre-Sterilized In Individual Packing • Should Be Available In Both 21Mm And 25Mm Sizes • Should Be Available In Individual And Assorted Packing) , Dental Bone Graft (Specification- • Xenogenic And Synthetic Material • 300-2500Mm Size • Perioglass, Adbone, Bio-Oss, Gem-21 • Resorbable) , Dental Calcium Hydroxide Powder & Zinc Phosphate Cement (Specification- Fda Approved, Ce Marked) , Dental Composite Anterior Micro Fill (Specification- Fda Approved Imported Isi/Iso/Ce Marked) , Dental Composite Material Nano Hybrid (Light Cure) (Specification- Dentsply/3 M/Kulzer/ Similar/ Isi/Iso/Ce Marked Complete Kit With Multiple Shades. Etchant And Bonding Agent, Applicator Tips/Brushes Isi/Iso Ce Marked) , Dental Edta Gel (Specificatio- Edta 15% With Carbamide Peroxide Gel 10% Root Canal Preparation Gel, Syringes, 3Gm Each) , Dental Edta Solution (Specification- Root Canal Chelating Agent Used During Root Canal Treatment To Case Enlargement And Shaping Of Canal 15 - 18 % Edta Solution, Ce Approved (Prevest/ Prime Dental Rc)) , Dental Endodontic Absorbent Paper Points Size: 15-40 (Specification- • Should Be Color Coded And Correspond To Instrument Sizes • 2%, 4%, 6% Taper • Should Be Available In Both Individual And Assorted Packing) , Dental Glass Ionomer Silver Reinforced (Specification- Fda Approved Imported, Isi/Iso/Ce Marked Pack) , Dental Glass-Ionomer Cement (Oic) Type 2 (Specification- Radiopaque Glass Ionomer Restoration Material Imported Type 2 With Mixing Pad Matrix Strips And Spatula, Power / Liquid Fda Approved Imported Restorative Material Isi/Iso/Ce Marked (Gdc/3M/Dentsply/Similar)) , Dental Gloves (Specification- • Surgical And Disposable • 6,6 And Half ,7 Size • Latex And Vinyl ) , Dental Granulated, High Density Glass Ionomer Powder + Liquid For Filling Purpose. (Specification- Isi/Iso/Ce Marked, Granulated Glass Ionomer Powder To Provide Good Flow Ability For More Accurate And Reproducible Dosing. It Should Provide Case Of Handling (Faster And Easier Mixing) And Consistent Mixing, Used As A Base, Semi- Permanent Restorations, Core Buildups And Minimal Invasive Dentistry And A Traumatic Restorative Dentistry. Pack Of Powder+Liquid+ Mixing Pad +Scoop) , Dental Gutta Percha Points (All Sizes) In Separate Boxes Gutta Percha Individual Size 15,20,25,30,35,40,45,50,55,60,6570,75,80; 15-40 And 45-80 Each Pack Contains 100 Nos 28Mm Long Flat Ended Gp Points (Specification- • Isi/Iso/Ce Marked • Should Not Bend While Inserting • Should Not Be Brittle • Radio Opaque • Should Be Color Coded And Correspond To Instrument Sizes • 2% Taper • Should Be Available In Both Individual And Assorted Packing • Dentsply) , Dental Hydrogen Peroxide 3% 500Ml Bottle (Specification- Hydrogen Peroxide 3% 500Ml Bottle) , Dental K-Files 15-40 (21Mm,25Mm,31Mm) 45-80 (21Mm,25Mm,31Mm)Endodontic Files K-Files Size No.8,10,15,20,25,30,23.40,45,50,55,6 0,65,70,75,80 15-40 And 45-80 (Specification- • Stainless Steel Flexible Files • Isi/Iso/Ce Marked • Handles Should Be Color And Number Coded With Eye For Floss • Prefitted Silicon Stops • Should Be Available In 21Mm, 25Mm And 31Mm Lengths With 2%Taper • Should Be Available In Both Individual And Assorted Packing • 1 Pack Of 6 Files (Mani Files) , Dental La With Adrenaline (Specification- Lignocaine Hydrochloride And Adrenalin Injection 30Ml Im) , Dental La Without Adrenaline (Specification- Lignocaine Hydrochloride Injection30ml Im) , Dental Mineral Trioxide Aggregate (Specification- • Prevest • Bioceramic Material) , Dental Pedo Files (Hand Files And Rotary Files) (Specification- • Mani Files • K Files 18 Mm Size • Stainless Steel • Handle Should Be Color For Ease Of Identification • Designed For Bulk Removal Of Pulp Tissue • Pre-Sterilized In Individual Packing) , Dental Phosphoric Acid Etchant (Specification- 35% High Viscosity Phosphoric Etch, Ideal For Enamel Etching, Blue In Color For Easy Visualization And Contrast) , Dental Pro Taper Gp 21Mm, 25Mm,31Mm) F1,F2,F3 Gp (Specification- • Should Not Bend While Inserting • Should Not Be Brittle • Radio Opaque • Should Be Color Coded And Correspond To Instrument Sizes • 4%, 6% Taper • Should Be Available In Both Individual And Assorted Packing Dentsply) , Dental Pulp Devitalize (Specification- Isi/Iso/Ce Marked Imported) , Dental Radio Opaque Calcium Hydroxide Cavity Liner. -Paste Of Ca(Oh)2 Paste + Catalyst (Specification- Self-Curing Calcium Hydroxide Preparation For Use In Direct And Indirect Pulp Capping. Available As Pack Of Base And Catalyst Pastes (11 Gms, 13 Gms Respectively Each) With Mixing Pad, Ce Approved) , Dental Root Canal Disinfectant Consisting Of, Thymol, Dexamethasone (Specification- Root Canal Disinfectant Consisting Of Dexamethasone, Thymol, Chlorhexidine) , Dental Root Canal Sealer (Indomethacin) (Specification- Radio Opaque Sealapex Dentsplya, Endoseal, Ivoclar, Sybronendo) , Dental Rotary Files 21Mm,25Mm (Specification- • Stainless Steel Files And Flex Files • Isi/Iso/Ce Marked • Handles Should Be Color And Number Coded With Eye For Floss • Dentsply, Neoendo • Should Be Available In Both Individual And Assorted Packing) , Dental Sodium Hypo Chloride (Specification- Sodium Hypo Chloride- 5% For Dental Use 500Ml Liquid Bottle) , Dental Suction Disposable Tips (Specification- 100 Tips / Per Pack) , Dental Suture (Specification- • Silk, Monofilament, Vicryl, Cat-Gut, • 2-0,3-0,4-0,5-0 Size • Jhonsons Company, Ethicon • Reverse Cutting, Round, Cutting • 1/4Th , 3/4Th ,1/2Th ) , Dental Temporary Restoration Material (Specification- Ready To Use, Temporary Filling Material, Fluoride Releasing Moisture Activated Cavit) , Dental X-Ray Developer (Specification- Powdered Forms Should Contain 2 Kg In One Pack Isi/Iso/Ce Marked) , Dental X-Ray Film Digital , Dental X-Ray Film Size 31 X 41 Mm (150 Films / Pkt) , Dental X-Ray Film (Specification- I0pa Film Size 0 (2.2X3.5 Cm - Fuji Or Equivalent) (Should Contain 150 Nos. Of Films In One Pack) Isi/Iso/Ce Marked) , Dental X-Ray Film (Specification- I0pa Film Size 2 (3X4 Cm Fuji Or Equivalent) (Should Contain 150 Members Of Films In One Pack) Isi/Iso/Ce Marked) , Dental X-Ray Fixer (Specification- Powdered Form Should Contain: 2 Kg In One Packisi/Iso/Ce Marked) , Desirepoly Bag Colour Sutable Forapprox 35Ltr Dustbeen 55 Micron , Desire Poly Bag Colour Sutable Forapprox 10Ltr Dustbeen 55 Micron , Desire Poly Bag Colour Sutable Forapprox 60Ltr Dustbeen 55 Micron , Desired Bio Hezard Poly Bag Capacity Of 30 Ltr , Desired Bio Hezard Poly Bag Capacity Of 40 Lit , Desired Bio Hezard Poly Bag Capacity Of 50 Ltr , Desktop I3- 10Th Generation Intel® Core™ I3 Processor Windows 10 Home Single Language 64 4 Gb Ddr4-2666 Sdram (1 X 4 Gb) 1 Tb 7200 Rpm Sata Hdd , Desktop I5- 10Th Generation Intel® Core™ I5 Processor Windows 10 Home Single Language 64 8 Gb Ddr4-3200 Sdram (1 X 8 Gb) 1Tb 7200Rpm Sata , Desktop I7- 10Th Generation Intel® Core™ I7 Processor Windows 10 Pro 64 8 Gb Ddr4-2933 Sdram (1 X 8 Gb) 1 Tb 7200 Rpm Sata Hdd , Developer Single Bath Liquid Concentrated Of Consistent Quality. It Sould Have Favoutable Contrast/Fog Ratio And Good Shelf Life - (5 Ltr Can To Make 22.5 Liters Working Solution) , Developer Single Bath Liquid Concentrated Of Consistent Quality. It Sould Have Favoutable Contrast/Fog Ratio And Good Shelf Life-2 Lit Can( To Make 9 Liters Working Solution) (Bromodex Mp Developer Concentrate) 9Ltr Packing , Developer Single Bath Liquid Concentrated Of Consistent Quality. It Sould Have Favoutable Contrast/Fog Ratio And Good Shelf Life-3 Lit Can( To Make 13.5 Liters Working Solution) (Bromodex Mp Developer Concentrate) 13.5 Ltr Packing , Diagnostic Strips For Urine Sugar/Albmin Packing: Of 100 Strip/Pkt , Diamond Marke Pencil , Digital Clock Wall Standard Company , Digital Thermometer , Digital Wrist Watch , Digital X Ray Film (Pack Of 100)),Film Size4 Inch X 17 Inch D , Digital X Ray Film -10X12 (150 Films/Pkt) , Digital X Ray Film -11X14 (150 Films/Pkt) , Digital X Ray Film -8X10 (150 Films/Pkt) , Digital X-Ray Film Size 14 X 17(50 Sheet Per Packet) , Diluent M-30D-(20Ltr) , Dionised Water 5 Ltr Cane(Each), , Disinfectant Renaclean Cold Sterilant (5 Ltr Can) , Disinfectant Renasteril Hot Disinfectant (5 Ltr Can) , Disposable Appronpvc Full Size , Disposable Bed Sheet 60X96 , Disposable Cresent Knife(2.2Mm), , Disposable Cup For Urine-Sputum 30Ml 80 To 90 Mm Diameter 100/Pkt , Disposable Dust Mask - Jl246c Equivalent To N-95 Mask 100 Pcs , Disposable Laboratory Coat Large Blue Colour , Disposable Laboratory Coat Large White Colour , Disposable Laboratory Coat Medium Blue Colour , Disposable Laboratory Coat Medium White Colour , Disposable Vial 3Ml(Each) With Air Tide Cap , Distilled Water 5 Lit , Domestic Hut 8.5 X 6 X 13 , Door Matte Big Size Jooth (Sandard Quality) , Door Matte Big Size Plastic (Sandard Quality) , Door Matte Medium Jooth (Sandard Quality) , Door Matte Medium Plastic (Sandard Quality) , Drabkin Solution For Hb 5 Lit , Draw Sheet Bleach 45 X 45 , Dressing Drum (Made Of Ss) (Size:-11X9) Standard Qualtiy , Dressing Drum (Made Of Ss) (Size:-9X9) Standard Qualtiy , Dressing Drum Ss Size 11X15 Standard Qualtiy , Dressing Drum Ss Size 6X6 Standard Qualtiy , Dressing Trolley - Frame Work Made Of 1 Vertical M.S Pipe , Two S.S Shelves Over With S.S Railling On All Four Sides , The Trolley Fitted S.S Bucket And Bowl And Mounted On 4 Dia Castors.Over All Size 30Lx18Wx32H, Finish Pre Treated And Epoxy Powder Coated, Also Available In Complete S.S , Drill Sleev For 2.7 & 3.2 Mm Drill Bits , Droper 2Ml , Drug Trolley Emergency , Dry Mop Complete , Dust Pan , Dustbin Foot Operated Plastic, Size 10 Ltr, Isi Mark , Dustbin Foot Operated Plastic, Size 15 Ltr, Isi Mark , Dustbin Foot Operated Plastic, Size 20 Ltr, Isi Mark , Dustbin Foot Operated Plastic, Size 25 Ltr, Isi Mark , Dustbin Foot Operated Plastic, Size 30 Ltr, Isi Mark , Dustbin Foot Operated Plastic, Size 5 Ltr, Isi Mark , Dustbin Without Foot Operated Plastic ,Size 10 Ltr,.Isi Mark , Dustbin Without Foot Operated Plastic,Size 15 Ltr,.Isi Mark , Dustbin Without Foot Operated Plastic,Size 20 Ltr,.Isi Mark , Dustbin Without Foot Operated Plastic,Size 25 Ltr,.Isi Mark , Dustbin Without Foot Operated Plastic,Size 30 Ltr,.Isi Mark , Dustbin Without Foot Operated Plastic,Size 5 Ltr,.Isi Mark , Dustbin Without Foot Operated Steel, Size 10 Ltr,.Isi Mark , Dustbin Without Foot Operated Steel, Size 15 Ltr,.Isi Mark , Dustbin Without Foot Operated Steel, Size 5 Ltr,.Isi Mark , E.D.T.A. Vacunater With Needle(3 Ml),Consumable , Ecg Paper (Chemical Coated)(80Mmx 20 Mtr Each), , Ecg Paper (Chemical Coated)(80Mmx 20 Mtr Each),Consumable , Ecg Paper(Chemical Coated) 50Mm X 30 Mtr. Roll , Ecg Paper(Chemical Coated) 50Mm X 30 Mtr. Roll , Ecg Paper(Wax Coated) (50Mm X 30 Mtr, Roll), , Ecg Paper(Wax Coated) (50Mm X 30 Mtr, Roll),Consumable , Ecg Paper(Wax Coated) Heavy Quality 50Mm X 30 Mtr/ Roll , Ecg Paper(Wax Coated) Heavy Quality 50Mm X 30 Mtr/ Roll , Economical & Compact , Edta K3 Vial Each , Edta K3 Vial Each , Edta Powder(250 Gm),Consumable , Edta Solutions K3 (150 Ml) , Edta Solutions K3 (150 Ml) , Edta Solutions K3 (500 Ml) , Edta Vial With Safty Cap (2Ml.) , Edta Vial With Safty Cap (2Ml.) , Edta Vial With Safty Cap (2Ml.) Capsule , Ehrilichs Aidehyde Reagen (2X250 Ml),Consumable , Ehrilichs Aidehyde Reagen (2X250 Ml),Consumable , Electric Drill Set Man Man , Electric Geyser 10 Ltr Capacity Isi Marked , Electric Geyser 15 Ltr Capacity Isi Marked , Electric Geyser 20 Ltr Capacity Isi Marked , Electric Geyser 50 Ltr Capacity Isi Marked , Eletric Torniquet , Elisa Reader - 0.000-3.5 Abs Mesurent Range, 500 Test Programe & 10000 Result Store, Bichromatic Optic System With Plate Shaker, External Mouse For Easy Handing Large Touch Screen, Whole Plate Reading In Just 5 Sec , Elisa Reader & Washer Printer , Elisa Washer - 48 User Programmable Wash Protocoles, 8 Way/12 Way Manifold, Auto Calibration, Washes Flat Round & V-Bottom Well, Well Depth Detection , Empty Bottel 500Ml With Cap , Endotracheal Tube Internal With Radioopaque Line(Dia 2.5 Mm To 5 Mm, Each), , Endotracheal Tube, Soft Cuff Towards The Distal End Kink Resistant Inflation Tube Murphy Eye At Distal End With Polished Smoothness Standard 15 Mm Connector Sterile, Single Use Curved Shaped Blister Pack-Suiting The Shape Of Product(Size 4 , Each),Tube , Endotracheal Tube,Soft Cuff Towards The Distal End Kink Resistant Inflation Tube Murphy Eye At Distal End With Polished Smoothness Standard 15 Mm Connector Sterile, Single Use Curved Shaped Blister Pack-Suiting The Shape Of Product(Size 3),Tube , Endotracheal Tubes Size 7 Cuffed Should Have Low Pressure High Volume Cuff And Radio Opaque Blue(25Each), , Endotracheal Tubes Size 8 Cuffed Should Have Low Pressure High Volume Cuff And Radio Opaque Blue(25 Each), , Endotracheal Tubes Size 9 Cuffed Should Have Low Pressure High Volume Cuff And Radio Opaque Blue(25 Each), , Enema Appratus 1000 Ml Stainless Steel And Rubber Connection Tube Standard Qualtiy , Enema Sodium 100 Ml (Sodium Acid Phosphate 10 Gm, Sodium Phosphate 8 Gm / 100 Ml) With Tube , English Plier , Examination Gloves Disposable Made Of Natural Rubber Latex, Pre-Powdered, Non-Streile Medium , Examination Gloves Disposable Made Of Natural Rubber Latex, Pre-Powdered, Non-Streile Small , Examination Gloves Disposable Made Of Natural Rubber Latex, Pre-Powdered, Non-Streile, Size:- Large , Executive Chair Foam With Leather Standard Company , Extractor For Radius Ulna Nailing , Exust Cooler Plastic Body Standard Size (Water Tank Cap.100 Liter) , Face Shield Protector Safaqi( ),Consumable , Factor Ix Deficient Plasma (Less Than 1%)(10X1 Ml),Consumable , Factor Vii Deficient Plasma ( Less Than 1%)(10X30 Ml),Consumable , Falcon Tube Plastic Contianers With Air Tight Cap , Falcon Tube Plastic Contianers With Air Tight Cap , Fauchets Reagents (125 Ml),Consumable , Featal Doppler , Female Reprodective System Complete , Field Stain A 500Ml , Field Stain B 500Ml , Filter For Complete Pulmonary Function Testing (Including Dlco) With Body Box(100 Filters Per Pack, Make- Medisoft Sa),Consumable , Filter For Complete Pulmonary Function Testing (Including Dlco) With Body Box(100 Filters Per Pack,Consumable , Filter Paper Sheet (Whatmann No 01) Pack Of 100 Sheets , Finite Pump Finish- Pre Treated And Epoxy Powder Coated , Fire Extinguisher Cylander Abc Powder Type 2 Kg Complete , Fire Extinguisher Cylander Abc Powder Type 4 Kg Complete , Fire Extinguisher Cylander Abc Powder Type 6 Kg Complete , Fire Extinguisher Cylander Abc Powder Type 9 Kg Complete , Fire Extinguisher Cylander Abc Powder Type Refling For Per Kg , Fire Extinguisher Cylander Abcd Type 2 Kg Complete , Fire Extinguisher Cylander Abcd Type 4 Kg Complete , Fire Extinguisher Cylander Abcd Type 6 Kg Complete , Fire Extinguisher Cylander Abcd Type 9 Kg Complete , Fire Extinguisher Cylander Abcd Type Refling For Per Kg , Fistula 16G, Single Sterilizedsingle Needle Packing , Fistula 17G, Single Sterilizedsingle Needle Packing , Floor Cleaning 1 Liter Isi Mark , Floor Cleaning 1000 Ml Isi Mark , Floor Cleaning 20 Liter Isi Mark , Floor Cleaning 5 Liter Isi Mark , Floor Cleaning Liquid Cleaning 5 Lit , Floor Duster , Floride Vial With Sp Pack Of 100 , Flouride Solution (Pot.Oxalate 5% Flouride 1%) Pack Of 150Ml , Flow Regulator (Dial Flow)(Each), , Foetal Doppler , Foetal Stethoscope , Foot Operated Sanitizer Ss With 1 Liter Botal With Disp. Pump , Foot Staire , Foot Step Double Steel Iron Standard Qualtiy , Forcepartery Sp Wells Cvd. 20 Cm/8” Standard Qualtiy , Forcepkocher Artery Cvd 8 “ Standard Qualtiy , Forcepkocher Artery Str 8 “ Standard Qualtiy , Forcep Allis Tissue 4 ?5Th20 Cm/8” Standard Qualtiy , Forcep Artery Mosquito Cvd 12.5Cm/5” Standard Qualtiy , Forcep Artery Sp Wells Cvd. 15 Cm/6” Standard Qualtiy , Forcep Dis Sectionplain Ss 17.5 Cm Standard Qualtiy , Forcep Dis Section Plain Ss 20 Cm Standard Qualtiy , Forcep Hysterectomystandard Qualtiy , Forcep Intestinalsize 16 Cm Standard Qualtiy , Forcep Intestinal Size 12.5 Cm Standard Qualtiy , Forcep Mousquito Str+Cvdsize: 12.5 Cm , Forcepsplain Size 10 For Dressing S.Steel , Forcepsplain Size 12.5 For Dressings.Steel , Forcepsplain Size 17.5 For Dressings.Steel , Forcepsteeth Size 15 For Dressings.Steel , Forcepsteeth Size 25 For Dressings.Steel , Forceps Plain Size 20For Dressings.Steel , Formaldehyde (Formalin)34% Acq 450 Ml Bottle , Formaldehyde 40% (Conc. Formaline)(1 X 5 Lit), Cen , Formalin Chamber Internal Trays Sterdization Size 21X8X8.5Standard Quality , Formalin Chamber Internal Trays Sterdization Size 21X8X8.5Standard Quality , Formoline Solution 450Ml , Freedge Domstic 165 Litre Standrad Company Isi Mark , Freedge Domstic 220 Litre Standrad Company Isi Mark , Fumigator , Gauze Swab/Pad 4 Layer 10Cmx10cm , Gauze Swab/Pad 6 Layer 10 Cmx 10 Cm , Gauze Swab/Pad 6 Layer 20 Cmx 20Cm , Generator Silent Disel 15Kvax12kv Dg Set Standrad Company Isi Mark , Generator Silent Disel 20Kvax16kv Dg Set Standrad Company Isi Mark , Glacial Acetic Acid (1 Liter), , Glacial Acetic Acid (2.5 Liter) , Glacial Acetic Acid (2.5 Liter),Consumable , Glacial Acetic Acid (500Ml), , Glass Slide 75Mm X 25Mm 1.1 Mm , Glass Slide 75Mm X 25Mm 1.35 Mm , Glass Slide With Isi Mark-At Least 75Mm X 25 Mm- Thickness At Least 1.1Mm,Detail Specifications-I-With Smooth Edges, Without Any Scrathtches. Ii-Glazed Glass.Iii-No Visual Or Chromatic Abbretions(50Slides/Packet), , Glass Test Tube 12 X 100 (Medium Size) Heavy Quality 100/Pkt , Glass Test Tube 12 X 75(Small Size) Heavy Quality 100/Pkt , Glass Test Tube 5 Without Edge [987879] , Gloter Aldhiygde Solution Packge 1 Ltr , Gloves B.I.S Specification Gloves, Surgical Rubber, Made Of Hypoallergic Latex 100%, Electronically Tested Sterilized 6 Inch / Pair(Pair),Surgical Material Disposable , Gloves B.I.S Specification Gloves, Surgical Rubber, Made Of Hypoallergic Latex 100%, Electronically Tested Sterilized 6.5 Inch / Pair(Pair), Disposable , Gloves B.I.S Specification Gloves, Surgical Rubber, Made Of Hypoallergic Latex 100%, Electronically Tested Sterilized 7 Inch / Pair , Gloves Isi Marked Surgical Rubber Hypoallergenic Latex 100% Powder Free 7 1/2 Inc Disposable , Gloves Isi Marked Surgical Rubber Latex 100% Powder Free 6 Inches Disposable , Gloves Isi Marked Surgical Rubber Made Of Hypoallergenic Latex 100% Powder Free 7 Inches Disposable , Gloves Latex Examination (Large) (100/Pkt)(Packet) , Gloves Latex Examination (Medium) (100/Pkt)(Packet) , Gloves Latex Examination (Small) (100/Pkt)(Packet) , Gloves Latex Examination No.8 (100/Pkt)(Packet) , Gloves Postmartam 10 Pack , Gloysine Board , Glucometer Cell , Glucometer Sprips (1X100) , Glucometer Strips 1 Should Be Able To Use Capillary Blood Samples 2 Should Have Expiry As Printed On The Label Of The Supplied Box(3 All Strips Should Have At Least One Year Expiry Date From The Date Of Supply 1 Glucometer Free With Each 1 Thousand Strips Rate Should Be Quoted For , , Glucose Kit (God/Pod)(350Ml),Digonstic , Glutaraldehyde Solution 2% In 1 Litre Can (2 Strips/Vials Per Each Can)(1 Litre Can)] , Glutaraldehyde Solution 2% In 5 Litre Can (2 Strips/Vials Per Each Can)(5 Litre Can)] , Gram Iodine (Gram Stain) 125 Ml , Grasper- Laparoscopic 5Mm Straight 360 Degree Rotating With Insulated Shaft, Toothed A Traumatic Grasper With Ratchet Mechanism, Plastic Grip(36 Cms Length, Independently Moving Jaws),Consumable , Gynec Sheet 80 X 48 Standard Pvc Quality , Gypsona 4” , Gypsona 6” , Haemoglobin Pippate , Haemoglobin Tube , Haemoglobino Meter (Sahilmathard) , Half Volume Pt And Aptt Testing , Hand Drill , Hand Sanitizer With Pump(500Ml),Bottle , Hand Wash Liquid Cleaning Standard Company , Hand Wash Solution With Dispenser 500 Ml , Hb Colour Scal Book , Hbnc Kit Complete - Digital Wrist Watch1 Digital Thermometer 1 Nenatal/Infant Weighing Scale With Sling1 Warm Sleeping Bag For Neonates 2 Blankets For Neonates 3 Mucus Extractor2 Baby Feeding Spoon1 Torch With Cells1 Spoon1 Bag For Carrying Kit/Material During Home Visit1 , Hbsag Antigeng Kit Card(Pack Of 10 Card Test With 10 Dropper, 1 Buffer Solution, 10 Pricking Lancet And 10 Alcohol Swab),Digonstic , Hcl (1X500 Ml = 500 Ml), Conc , Hcl 35-37, 500 Ml Pack , Hcl N/10 (500 Ml Bottle) , Hcv Kit Card Test(25 Test Kit Pack), Digonstic , Hcv Rapid Test Card Single Test (J Mitra/ Span/ Tulip) , Heavy Duty Beam Rack For Ware House , Hemotocyto Meter, , H-Files 15-40(21Mm,25Mm,31Mm) 45-80 (21Mm,25Mm,31Mm) Headstrom Files (H-Files) Size No.15,20,25,30,35,40,45,50, 55,60,65,70,75,80 15-40 And 45-80 (Specification- • Stainless Steel Flexible Files • Isi/Iso/Ce Marked • Handles Should Be Color And Number Coded With Eye For Floss • Prefitted Silicon Stops • Should Be Available In 21Mm, 25Mm And 31Mm Lengths With 2% Taper • Should Be Available In Both Individual And Assorted Packing • 1 Pack Of 6 Files , Hiv 1&2 Test Cards , Hiv 1+2 (Rapid) Per Card , Hiv Rapid Test Card Single Test (J Mitra/ Span/ Tulip) , Hohmann Retractor , Hoilow Mill , Hole Towel Eye Drape (Size-70*70Cm Area 08*08) , Hooks For K Nail Retractor , Hospital Bed Powder Coted Size 84Lx36Wx24H , Hospital Bed Ss 6X3x2.5 With Mattress 6X3x4 , Hot Water Bag Isi Mark Standard Company , Hub Cutter- Non Electric Lockable Safety Portable Box For Disposal Of Hypodemic Needles. , Hydrogen Peroxide (Conc.) H2o2 (500 Ml), , Hydrolic Ot Table , I.V Set (Child) With Airway And Needle Standard Company , I.V Stand Powder Coted 4 Legs Base , I.V Stand Ss 4 Legs Base , I.V.Set (Adult) With Airway And Needle Standard Company , Ice Gel Pack 200 Gm , Ice Gel Pack 500Gm , Id Wrist Band(Identification For Mother/Child Specific Colour)(Wrist Band/No), , Incubater B.O.D , Incubator , Indicator Sol, For Ph (Litmus Sol) (1X500 Ml = 500 Ml) , Infant Feeding Tube (Catheter)(10 G, Each), , Infant Feeding Tube Size: 10G , Infant Feeding Tube Size: 3G Catheter , Infant Feeding Tube Size: 4G Catheter , Infant Feeding Tube Size: 5G , Infant Feeding Tube Size: 6G , Infant Feeding Tube Size: 7G , Infant Feeding Tube Size: 8G , Infant Mucus Extractor Sterile Pvc(Each),Surgical Material , Infant Weing Scal With Bag , Infantometer , Infrared Hemoglobin Meter Isi Company , Infusion Pump Features :- Front Load Of Yringe , Automatic Detection Of Syring, Bolus And Purge Facilty , Self Illutrative Contorl Panel , Syring Capacity , 10Ml-300Ml/Hr.20Ml-500Ml/Hr , Instrument Tray Ss With Cover 10X8 Standard Company , Instrument Tray Ss With Cover 15X12 Standard Company , Instrument Trays With Cover Size: 10 X 12 Standard Company , Instrument Trays With Cover Ss Size: 7 X 11 Standard Company , Instrument Wash Solution 500Ml With Spray Pump , Insulated Container , Intracath Cannula For Single Use (Intravascular Catheters) Bis(Gauze 22, Length 25), , Inverter Battery 500 Watt 150 Ah Isi Mark , Inverter With Battery 1000 Va [One Battery Required]Isi Mark Standard Companywith Installation , Inverter With Battery 1500 Va [Two Battery Required]Isi Mark Standard Companywith Installation , Iron Box 5’X2.5’X2.5’’ , Iron Box 6’X3’X3’’ , Iron Lock Standard Size , Iron Stand With Belding Work , Isopropyl Alcohol (Propanol)(1 X 2.5 Lit), , Iv Cannula Size With Injection Valve (18G ) , Iv Cannula Size With Injection Valve (22G ) , Iv Cannula Size With Injection Valve (24 G) , K Wire (Length 375Mm Size:1.6Mm Roll) , K Wire (Length 375Mm Size:1.8Mm Roll) , Kangaroo Mother Care Gown Design (Kmc) Stared Size Cotton , Keratom Knife(2.8Mm), Disposable , Keratome 3.2 Keratome Round Stock 3.2Mm Full Handle Knives E.T.O. Sterile Angled Bevel Up 45 Deg(), , Key-Board (Tvs/Cherry) , Key-Board Standard Quality Repudate Company , Kmc Chair We Klm Healthcare And Equipments Deals In All Hospitals Furniture. We Are Leading Manufacturers In Hospital Furniture And We Deals In Mild Steel, Stainless Steel And Aluminium Hospitals Furnitures. We Have Wide Range Of Products With Quality Of Material And With Good Price Range. We Also Deal In Hospitals, Icu And Clinic Furnitures..Like Fowler Beds, Electric And Manual And Stretcher And Trolley And Bed Side Lockers,Dustbins,Stool Beds..You Can Contact Us Via Mobile, Sms And Mails. , Knife Blade All No Pack Of 100 , Konika Minolta Photocopier Presser Roller , K-Wire Bender Steel , K-Wire Cutter Medium , Lab Coat , Labour Room Fumigation Solution Preparation Labour Room Measurement 16(Wt)X23(L)X12(Ht)=4416 Cubic Ft 0.01% Silver Nitrate 10% Hydrogen Peroxide 20% Solution =754 Ml 80% Water =3662 Ml Total Prepared Solution =4.416 Liters , Labour Room Tray 12”X10” , Labour Room Tray 12”X10” , Labour Room Tray 15”X12” , Labour Room Tray 15”X12” , Labour Table 3 Fold Ss With Foam Mattress, , Labour Table Hydraulic , Labour Table Manul , Laptop Charger/Acer/Lenovo,/Lg/Acer/Dell , Laptop Dell/Hp/Aser/Asus/Lenovo Company I3 , Laptop Dell/Hp/Aser/Asus/Lenovo Company I5 , Laptop Dell/Hp/Aser/Asus/Lenovo Company I7 , Larrynoscope Set With Four Blades (Adult) , Larrynoscope Set With Four Blades (Infant) , Larrynoscope Set With Four Blades (Paediatric) , Laser Printer , Lcd Projector (Multimedia Lcd Projectors. Our Offered Projectors Are Widely Used In Various Business Meetings, Events, Conferences, Presentation And Other Exhibition Shows. These Projectors Are Widely Acknowledged By Our Clients For Their User Friendly Settings And Hassle Free Operations. The Provided Projectors Are Precisely Manufactured At Our Vendors End Using The Modern Technology.) , Lcd Projector Brightness 3000 Lumens (2100 Lumens Eco Mode) Projection Distance 1.94M - 4.85M (3.23M To 3.55M For 100 Focal Length F 2.56 To F 2.8/ F - 21.0 To 23.1 Mm Lamp Type 190W P-Vip Native Resolution 180 X 800 (Wxga), 1024000 Pixels Video Formats 1080P / 1080I / 720P / 576P / 576I / 480P / 480I Screen Size 60 - 150 (129 X 81Cm - 323 X 202Cm) Imaging Technology 1.1 X Manual Type Reflective Dlp Chip Size And Number 0.65 Diagonal, Single Chip Projection Ratio 1.501 To 1.651 , Led 15 Standard , Led 17 Standard , Led 21 Standard , Led 23 Standard , Lenz Bone Holding Forcep , Liquid Paraffin 50Ml(Bottle ) , Liquor Ammonia (500 Ml),Consumable , Long Body Suit -Non Woven Fabrie , Long Line Silicon Catheter, G-24, Fr-2, L-30Cm , Low-Profile Titenium Chemo Port With Cilicon Catheter (9.6 Fr, 6.6Fr, 3.9Fr,) Length -60Cm,Guide Wire, Peel-Away Desilet,Hubsite Needle(22G*20Mm) , M-30-D-Diluent(20Ltr),Consumable , M-30-R-Rinse(20Ltr),Consumable , Macconckeys Agar(500Grm),Consumable , Macconckeys Agar(500Grm),Consumable , Mackintosh Double Colour Water Proof Rubber Marked Isi Hospital Rubber Sheeting Is:4135-1974 Packing And Making : As Per Clause No 4.1 And 4.3 / Mtr , Malaria Antigen Pv/Pf Single Test , Male Reprodective System Complete Standard Company , Malleable Splirls (X-Ray Through The Splints Fixing Of Splint Is By Zipper Or Belt Distal End Left Open To Expose Toes Should Be Washable And Reusable) , Mammanatallie Standard Company , Mammanatallie Standard Company , Manometer And Flo Meter For Oxygen Cylinder , Manometer And Flo Meter For Oxygen Cylinder , Maryland Dissector- Laparoscopic 5Mm Curved Maryland Dissector With Tapering End, 360 Degree Rotating With Insulated Shaft, Non Ratchet , Plastic Grip(36 Cms Length, Monopolar Pin Provision For Usage With Electro Surgical Unit, Independently Moving),Consumable , Mattres Cover Complete Size L.6.5Fxw3.5Fxt5.5F Inch , Mattress Coir With Foam Topping Plain Cloth Cover Size 72X36x4 Thik With Ragzine Cover , Medical Nitrous Oxide Gas In Jambo Size Cylinder(D Type),Miscellaneous , Medical Nitrous Oxide Gas In Medium Size Cylinder(B Type),Miscellaneous , Medical Nitrous Oxide Gas In Small Size Cylinder(A Type),Miscellaneous , Medical Oxygensteel /Aluminium Cylinder (10 Litres Water Cap) With Gas Specific Pin System(10 Liters),Inhalation , Medical Oxygen Gas Ip In Jambo Size Cylinder(D Type),Miscellaneous , Medical Oxygen Gas Ip In Medium Size Cylinder(B Type),Miscellaneous , Medical Oxygen Gas Ip In Small Size Cylinder(A Type),Miscellaneous , Medical X-Ray Film-Polyester Based Imaging Film 30.5 Cm X 30.5Cm (12X12) Size:- 50 Sheets In One Packet , Medical X-Ray Film-Polyester Based Imaging Film 35.6 Cm X 43.2Cm (14X17) Size:- 50 Sheets In One Packe , Medical X-Ray Film-Polyester Based Imaging Film 35.6Cm X 35.6Cm (14X14) Size:- 50 Sheets In One Packet , Medigard Hand Scrub , Messuring Cylinder 1Ltr With Spout , Mesuring Cylinder Pack Of 100Ml , Mesuring Cylinder Pack Of 1Lit With Spout , Mesuring Cylinder Pack Of 500Ml , Methanol(Acetone Free) For Leishman Staining (1X2.5Lit) , Methanol(Acetone Free) For Leishman Staining (1X2.5Lit) , Methnol , Methylate Spirit (Sep.Chemical Name Ethanol Denatured+5% Isopropyl Alcohol+5%Methanol, Molecularstructure : C2h50h Molecular Wt: 46.07 Purity : 90% , Methylene Blue 25Gm Dye Content 82% , Methylene Blue Pack Of 500Ml/Gram (Dye Content+42% Sepc.Chemical Name: Methylthionine Chloride, Chemical Structure: C16h18c1n3s,Molecular Wt: 319.9, Dye Content: Approx 82% (Should Be Available On The Container) , Micro Drip Set , Micro Pipet 1000 Fix And Variable Each , Micro Pipet 100-1000 Fix And Variable Each , Micro Tips Big Pack Of 500 Pices , Microalbumin Urine(100 Tests) , Micronthik Bag 10 Lit. , Micronthik Bag 10 Lit. , Micronthik Bag 30 Lit. , Micronthik Bag 30 Lit. , Micronthik Bag 5 Lit. , Micronthik Bag 5 Lit. , Micronthik Bag 50 Lit. , Micronthik Bag 50 Lit. , Micropiptte 100-1000 , Microscope With Digital Display And Having Magnification , Microsurgery Speciality Gloves(Size 6.5),Lens , Microtips (2-200 Ul) 1X1000(Each), , Milkiwhitegel Based Sanitizer1.Ethinol (Cas-64-17-5) 58-62% 2. Benzoil Coline Chloride 0.52% 1 % 3. Ph Neutral Contact Time 15 Sec 4.(Pack Size L& 500 Ml With Dispensor), , Mobile Operating Light Double Dom Isi Mark Standard Company , Mobile Operating Light Four Dom Isi Mark Standard Company , Mobile Operating Light Single Dom Isi Mark Standard Company , Mobile Operating Light Three Dom Isi Mark Standard Company , Mopping Pad , Motorized Ot Table With Chair For Ophthalmology , Mouth Gage , Mtp Cannulas Standard Company , Mva Kit (Mannual Vaccum Aspiration Kit) , N-95 3M Disposable Raspirator(Without Valve Ffp2), , N-Acetyl L-Cystein , Nah2 Po4 (Anhydrous) Analar / Gr/Ar (1X500 Gm = 500Gm), , Naphthalene Balls , Nasal Prongs Catheters Child Size Disposable , Nebulization Mask - Kit (Pediatrics) , Nebulize Compressor. Piston Model, Fitted With Small Fan, Nices Less 60 Decible, Nebulizer Chamber Autoclave, Particle Size Between 0.5 To 5 Micron Suitable For Adult And Pediatric Patient. Resptrable Particle Above 60, Tor 300 Mg/Min , Needle And Syringe Destroyer Electrically Operated , Needle And Syringe Destroyer Manually Operated , Needle Holder Laparoscopic 5Mm Straight Reusable Needle Holder With Ratchet Mechanism With High Quality Tungsten Plated Jaws For Enhanced Needle Grip(36 Cms Metal Shaft), , Needle, 24G Surgical Material Disposable , Needles 22G Disposable , Needles 23 No Disposable , Needles 26G X 1/2 Disposable , Neonatal Infant Weighing Scal With Sling , Nibp (Non Invasive Blood Pressure) Multi Channel Monitor) , Nitric Acid (Hno3) (2.5 Liter), Con. , Nitrous Oxide Gas In Jambo Size Cylinder(D Type) , Nitrous Oxide Gas In Medium Size Cylinder(B Type) , Nitrous Oxide Gas In Small Size Cylinder(A Type) , Non -Contact Rapid Temperature Measurment System-Screen 2.8 Inch Tft Screen, Infrared Resolution Size 160X120, Frame Rate 9Hz, Temperature Measurment Range 30 Dig.C-45Dig.C, Accuracy + 0.5Dig.C, Distance 1M. Measuring , Storage - Take And Store Photos To Sd Card , Software Pc Analysis Software, Battery - Rechargeable 3.7V/5000Mah Lithium Battery. 22650 Single Cell, Battery Working Hrs- Up To 6Hrs.To Escort Your Continucous Work, Weather Proof, Nycocard Reader -Up To 2M, Tripod Mounting Hole 1/4 Inch, Hba1c, Microabumin, D-Dimer, C-Reactive Proteins , Non -Invasive Ventilaor (Sponteneous And Timed) , Nylon Suture Spatulated Micropoint Reverse Cutting Needle, Double Armed Suture Size 9-0(12 Foils/Pkt),Suture , Obsteric Labour Talbe Mechacally :- Sep- Frame Work Made Of Heavy Ms Crca Tubular Pipe.Stainless Steel Top In Two Section , Back Rest Section Adjustable On Retched System, Trendleburg Position Adjustable On Screw Mechanism By Handle. Supplied With Waste Collecting , S.S Bowl On S.S Bracket And I.V Rod , Height Adjustable A Pair Of Leg Holders With Straps, Complete With Self Locking Traction Handle I.V Rod , Overall Size 72 Lx27Wx30H Cms.Finish Pre Treated And Epoxy Powder Coated.Also Available In Complete S.S , Oil Room Heater 15 Fins 2900 Watts , Oil Room Heater Ofr 13 Fin Ofr (Oil Filled Radiator)| Room Heater| 2900 W| 3 Thermostatic Heat Power Settings & Ptc Fan Control| Long-Lasting Heat| Comfortable Breathing| Uniform 360° Heating (Black) , Oil Room Heater Ofr 9 Fin Plus 2000W Oil Filled Room Heater For Home|Easy Breathing*| Duraprotek-Anti-Leak Fins|3-Yr Warranty400w Ptc Ceramic Fan Heater|3-Heat Setting-1000W/1500W/2500W|Black,2400 Watts , Operating Microscope For Ent (Imported) , Ophthalmo Scope Direct , Ophthalmo Scope Direct , Ophthalmo Scope In Direct , Ophthalmo Scope Indirect , Orthopaedic Speciality Gloves(Size 7),Consumable , Orthopaedic Speciality Gloves(Size 7),Consumable , Osteome Medium , Osteotome Large , Osteotome Small , Oxalic Acid , Oxygensteel /Aluminium Cylinder (10 Litres Water Cap) With Gas Specific Pin System(10Liters),Inhalation , Oxygen Conentrator , Oxygen Cylande Refling Jumbo Large , Oxygen Cylande Refling Medium , Oxygen Cylande Refling Small A Type , Oxygen Cylinder (It Should Be A Standard ‘J’ Type Molybdenum Steel Cylinder To Fill Medical Oxygen The Capacity Should Be Of 5000 To 6000 Liters (5To6m3) At A Pressure Of 1800- 2000Ibs/Inch2, A Pressure Regulator Capable Of Reducing The Pressure To Appropriate Level To Run Either A Ventilator Or Provide Oxygen Therapy With A Flow Meter Should Be Provided , Oxygen Cylinder (It Should Be A Standard ‘J’ Type Molybdenum Steel Cylinder To Fill Medical Oxygen The Capacity Should Be Of 5000 To 6000 Liters (5To6m3) At A Pressure Of 1800-2000Ibs/Inch2, A Pressure Regulator Capable Of Reducing The Pressure To Appropriate Level To Run Either A Ventilator Or Provide Oxygen Therapy With A Flow Meter Should Be Provided , Oxygen Cylinder Flow Meter , Oxygen Cylinder Gauge Valum , Oxygen Cylinder Gauze-1 , Oxygen Cylinder Gauze-2 , Oxygen Cylinder Jumbo Size Complete Set , Oxygen Gas Ip In Jambo Size Cylinder(D Type) , Oxygen Gas Ip In Medium Size Cylinder(B Type) , Oxygen Gas Ip In Small Size Cylinder(A Type) , Oxygen Humidifier , Oxygen Inhelation Mddial Oxygen Steel Aluminium Cylinder 10 Ltr , Oxygen Mask Adult (Standard Size) Standarad Company , Oxygen Mask Paediatric (Standard Size) Standarad Company , Paper Adhesive Microporous Surgical Tape 1 Inch X 9 M / Roll (10 Roll/Pkt) , Paper Adhesive Microporous Surgical Tape 1/2 Inch X 9 M / Roll (10 Roll/Pkt) , Paper Adhesive Microporous Surgical Tape 2 Inch X 5M /Roll , Paper Adhesive Microporous Surgical Tape 3 Inch X 5 M / Roll (10 Roll/Pkt) , Paper Adhesive Microporous Surgical Tape 4 Inch X 9 M / Roll , Paper Adhesive Microporous Surgical Tape 6 Inch X 10 M / Roll , Paper Gloves Size 7 Inchesdisposable , Paper Gloves Size 7,1/2 Inchesdisposable , Paraffin Strips , Pasteur Pipette Individually Packed Sterile 3Ml , Patch Buprenorphine(10Mcg),Consumable , Patch Buprenorphine(20Mcg),Consumable , Patella Holding Forcep Large , Patella Holding Forcep Small , Patient Gown Pvc Standard Size , Patient Gown Standard Size , Patient Stool Standard Size , Pcr Tube 0.2 Ml , Phenyl - As Per Schedule O (Grade 1) 10 Lt Jar(Isi Marked) , Phenyl - As Per Schedule O (Grade 1) 20 Lt Jar(Isi Marked) , Phenyl 40% /Phanolic Solution 40% 20 Lte. , Phenyl Crystal 1000 Ml Purity 99.5% , Phenyl Crystal 500Ml Purity 99.5% , Photo Calorimeter , Photo Therapy Unit Double Surface , Photocopier Machine A-3 Size (Canan India 2006N) , Photocopier Machine A-3 Size (Konica Minolta) , Phototherapy Unit , Pipete Graduated 0.2Ml , Plain Disposable Vial 3Ml(Each),Consumable , Plain Vial With Screw Cap (12 X 75), , Plain Vial With Screw Cap (12X75),Consumable , Plaster Of Paris Bandage 10 Cm X 2.7 Mtr / Roll(Roll),Bandage , Plaster Of Paris Bandage Bp 15 Cm X 2.7 Mts/Roll Standard Company , Plaster Of Paris Pack Of 5Kg , Plastic Bags 18X16x8 , Plastic Bottle(1000 Ml), Empty With Cap , Plastic Bottle(300Ml), Empty With Cap , Plastic Bottle(500 Ml), Empty With Cap , Plastic Box Supirior Quality 10X7x4 , Plastic Box Supirior Quality 9X3.5’X3’ , Plastic Box Supirior Quality 9X6’X6’ , Plastic Box Supirior Quality 9X6x4 , Plastic Bucket Black 20 Ltr , Plastic Container With 2Lt Cap , Plastic Tanki 1000 Ltr. For Water (3 Layerd, Standard Quality, Manu.By Reputed Company) , Plastic Tanki 500 Ltr. For Water (3 Layerd, Standard Quality, Manu.By Reputed Company) , Plate Holding Forcep Large , Plate Holding Forcep Medium , Plate Holding Forcep Small , Pneumatic Tourniquet , Poe 16 Channel , Poe 4+2 , Poe 8+2 , Poly Bag Black 16X18 Cap. Of 5 Kg Weight , Poly Bag Red 16X18 Cap. Of 5 Kg Weight , Polymed High Pressure Extension Tube, Length - 100Cm , Polymed High Pressure Extension Tube, Length - 150Cm , Polymed High Pressure Extension Tube, Length - 200Cm , Polymed Size - 1, (12 Foils/Pkt)(1/2 Cir Rb Needle 45 Mm, Length 90 Cm ),Needle , Polymed Size-2/0 (12 Foils/Pkt)(1/2 Cir Rb Needle 25Mm, Length 45 Cm),Needle , Polythine Whit Standard Quality(Weghting Capicty 10 Kg To 20Kg) , Poocha Long Cloth Standar Size , Portable Fogging Machine , Postmartem Gloves , Postmartem Set , Postmartem Set , Potassium Permanaganate , Pptubes For Centrifuge 50 Ml , Pregnancy Detection Kit Ce Marked/Isi Marked 30 Test/ Kit , Pregnancy Test Strips For Urine Pack Of 100 Strips , Pregnant Stage And Reprodective Dumy , Pricking Lancet (Pkt Of 200 Units)(Packet), Disposable , Pricking Lancet 100 Units Disposable , Printer Canon Lbp 2900B , Printer Colour Hp/Canon/Epson , Printer Epson L380 , Printer Epson M 200 , Printer Hp 1005 , Printer Hp 1020 , Printer Laser Printers: Monochrome, 600X600 Dpi, A4, 14Ppm, Usb,-(Each , Printer Lasesr: Colour, 600X600 Dpi, A4, 8 Ppm Bw& Ppm Colour(A4 Size), 16 Mb- (Each) , Printers Laser: Canon, 600X600 Dpi, A4, 14Ppm, Usb,-(Each) , Pro Taper Files Set Of 6 15-40 (21Mm,25Mm,31Mm) (Specification- Dentsply Set Of (21Mm,25Mm,31Mm) • Should Be Available In Both Individual And Assorted Packing •1 Pack Of 6 Files • Handles Should Be Color And Number Coded With Eye For Floss • Stainless Steel Files) , Pulse Oximeter Finger Tip , Pulse Oximeter Table Top , Punefure Proof Container , Purified /Distilled Water- Laboratory Grade , Pvc Carpet , Pyrethrum Extract 2%(25 Litre Drum) , Ra Factor 25 Test Kit Qualicative , Ra Factor 50 Test Kit Qualicative , Rbc Dialuation Fluid (500 Ml Bottle) , Reamers For Radius Ulna Nailing , Rectal Thermometer , Refrigrator 322 Liter , Resusciatation Set With Infant & Neonatal Mask , Retinoscope , Retractor Right Angle Large , Retractor Right Angle Medium , Retractor Right Angle Small , Revolving Stool 4 Leg Ss , Rib Belt Large(Mfg By - Precious Life Care) , Rib Belt Medium(Mfg By - Precious Life Care) , Rib Belt Small(Mfg By - Precious Life Care) , Rna Extraction Kit - Icmr Certified Kit(250 Test) , Road Broom With Handle , Rolled Bandaze 10 Cm X 5 Mtr. , Rolled Bandaze 15 Cm X 5 Mtr. , Rolled Bandaze 5 Cm X 5 Mtr. , Rolled Bandaze 7.5 Cm X 5 Mtr. , Room Heater Hot Air Blower 2 Kw , Room Spray , Ryles Tube (Pvc) Size : Adult16-18 ) , Ryles Tube (Pvc) Size : Children: 10-12 , Ryles Tube(Size 14 Each Piece) , Salt Testing Kit(As Per Attached Specification , Kit), , Sanitary Napkins Pack Of 6 Pc Standred Size , Sanitizer With Dispenser 100 Ml , Sanitizer With Dispenser 500 Ml , Scalp Vein Set Size 20 No Disposable , Scalp Vein Set Size 22 No(Each), Disposable , Scanner Canon Lide 110/Standard Company , Scanner Canon Lide 120 , Scessior Stainless Steel 8: , Scessior Stainless Steel 9: , Scissor Dressing Str/Cur Ss 12.5 Cm , Scissor Dressing Str/Cur Ss 15 Cm , Scissor Dressing Str/Cur Ss 17.5 Cm , Scissor Mayo Str/Cur Ss 16 Cm , Scissor With Round Trap , Scissors Str + Cvd Size 10 Cm Cutical , Scotch Bright , Screw Driver For 3.5 Mm Screws , Seenk Jhadoo (Standard Size) , Seman Diluting Fluid 100 Ml. , Sencer Senitizer , Senstivity Disk , Serological Water Bath With Digital Temprature Display Size 605X300x150mm , Shadowlessceiling Light: 28 Dome With Seven Reflector Each Fitted With A Halogen Bulbe And Spherical Filter Glass Ensuring Shadow Free Corrected And Cool Light With A High Intensity Of Illumination (Major Ligh Of 1,20,000 Lux And Satelite Of 75000 Lux , Sharp Collection Containers 1.5 L Disposable , Sharp Collection Containers 5 Ltr Disposable , Sideport Knife(Num), , Sideport Sics Blade (Sideport Entry Knife), , Single Umbilical Catheter With Leur Lock(Fr-3 To Fr 3.5 , L-40 Cm),Consumable , Single Umbilical Catheter With Luer Lock Stopcock Fr-2, L-40 Cm , Single Umbilical Catheter With Luer Lock Stopcock Fr-3, L-40 Cm , Single Umbilical Catheter With Luer Lock Stopcock Fr-4, L-40 Cm , Single Umbilical Catheter With Luer Lock Stopcock Fr-5, L-40 Cm , Slide Box Plastic Cap 100 Slide , Slide Box Plastic Cap 50 Slide , Slide Box Wooden Cap 50 Slide , Slide Holder (Made For Metal) , Slide Rack (Metal) For 25 Slides , Slide Stain Horigontal Cap 50 Slide , Slide Stain Vertical Cap 50 Slide , Slit Lamp With Stand , Snellens Vision Box Roted , Sodium Citrate 3.8% - 500 Ml , Sodium Hydroxide (Naoh) (Analar / Gr/Ar) (1X500 Gm = 500Gm), , Sodium Hypochlorite 5% Solution(5 Ltr),Solution , Sodium Hypochlorite Solution 100 Ml Bottle , Sodium Hypochlorite(0.03/5 Ltr),Solution , Sodium Nitroprusside (100 Gm), [710034] , Soft Board 3X4 With Cover , Soft Board 4X5 With Cover , Soft Roll 4” , Soft Roll 6” , Solar Inverter 850 Kva. Double Bettery Syestem. , Solar Led Street Lightning System Along With Mounting Pole , Spaculam , Spinal (L.P.) Needle Disposable 24G , Spinal (L.P.) Needle Disposable 26G , Spinal (L.P.) Needle(25G),Surgical Material Disposable , Spinal Needle 18 No. Disposable , Spinal Needle 22 No. Disposable , Spinal Needle 23 No. Disposable , Spinal Needle G-22 L-120 Mm*0.71/Piece , Spinal Needle G-23 With Metal Stylet. , Spinal Needle G-27 L-120 Mm*0.40/Piece , Spine Board (Should Be In Plastic Material At High Strength And Waterproof. It Should Be 4 Rules For The Quick And Total Fixing Of The Head Immobilizer And Two Cavities Waherthe Board Lays On The Floor.When The Base Is Blocked In The Traditional Way, That Allow A Avoid Damaes Of Rip-Off Straps During The Usage Of Accommodation In The Ambulance It Should Be Handles For The Transport, Supplied With 3 Belts With Rapit Unhooking Buckle Should Have Maximum Radio Transparemcy To Make Exams Without Compromise Patient Condition.) , Sponge Holding Forceps , Spreader 15-40 (21Mm,25Mm,31Mm) (Specification- • Nickel Titanium Files • Isi/Iso/Ce Marked • Handles Should Be Color And Number Coded With Eye For Floss • Prefitted Silicon Stops • Should Be Available In 21Mm, 25Mm • 2 % Taper • Should Be Available In Both Individual And Assorted Packing • 1 Pack Of 6 Files) , Spring Balance Capacity 15 Kgs (For Baby Weighing) , Spuum Containersep.(Cups Made Of Special Medical Grade Polypropylene, Thin Plastc, Transulucent, Diameter- 4Cm,Capacity-30Ml, Srewable Cap Should Also Be Made Of Special Medical Grade Polypropylene And Should Be Air Tight. Leak Proof. Pack Of 100 Pc , Stabilizer For Ac , Stain (1X25 Gm = 25 Gm),Consumable , Stainic Rack(Each),Consumable , Staining Kit Reticulin(100 Test),Consumable , Staining Rod Steel (60Cm) , Stainless Steel Wire 30G , Stainless Steel Wire 30G , Steam Stock System & Mositure Trap , Steel Drill Bits 2.7Mm 3.2Mm 3.5 Mm Steel , Steel Hammer Heavy , Steel Troch With 3 Cell , Steel Troch With 3 Cell Isi Mark , Sterilant Cold Disinfectant For Dialysis Containing Peracetic Acid Hydrogen Peroxide Acetic Acid(5 Ltr Can),Consumable , Sterilant Hot Disinfectant For Dialysis Containing 21% (Approx) Citric Acid, Malic Acid, Lactic Acid(5 Ltr Can),Consumable , Sterlizer Electrically Operated (Size 10X5X3) Isi Marked , Sterlizer Electrically Operated (Size 12X6X4) Isi Marked , Sterlizer Electrically Operated (Size 8X5X3) Isi Marked , Sterlizer Electrically Operated With Automatic Cut Off Ss 12X6X4 , Sterlizer Electrically Operated With Automatic Cut Off Ss 20X6X4 , Stethescope Super Quality , Stethoscope Litman Type , Stop Watch Digital , Strecher Folding Cloth Standred Quality , Stretcher Trolley 4 Wheel 79X24X30 Without Handle , Stretcher Trolley 6 Wheel 79X24X30 Without Handle , Strip For Albumin Urine And Suger , Strip For Malaria Antigen, P Vivex, P Falciparum , Suction Machine Portable Electric , Sulphosalicylic Acid 3% W/V Pack Of 500Ml , Sulphuric Acid ( H2so4, Molecular Wt.98.08, Minimum Assay: 98% Colour: Clear , Surface Disinfectant 10 Minute Aldehyde Free Disinfectant Containing Potassium Mono Per Sulphate Powder((5Kg Packet)),Powder , Surgeon Cap(Box Of 100 Caps) Disposable , Surgical Blade Isi Marked, Size 11(100 Per Packet),Surgical Material , Surgical Blade Isi Marked, Size 15(100/Pkt),Surgical Material , Surgical Blade Isi Marked, Size 22(100/Pkt),Surgical Material , Surgical Blade Isi Marked, Size 23(100/Pkt),Surgical Material , Surgical Blade Isi Marked, Size 24(100/Pkt),Surgical Material , Surgical Spirit 99.5 % 450 Ml , Surgical Spirit 99.5 %, Pack Of 5 Lte Can , Surgical Spirit(100Ml),Bottle , Suture Needles Curved 1/2 Circle Round Bodyassorted Size 11-15 , Suture Needles Curved 1/2 Circle Round Bodyassorted Size 1-5 , Suture Needles Curved 1/2 Circle Round Bodyassorted Size 16-20 , Synthetic Absorbable Suture 1 With 1/2 Circle Taper Cut Needle (H) Size :1 40Mm Length 90Cm Polyglycolic Acid (Pga) (12 Foils Per Pkt) , Synthetic Absorbable Suture 2/0 With 1/2 Cir Rb Needle Size:2/0 30Mm Length 90Cm-Polyglycolic Acid (Pga)12 Foils / Pkt , Synthetic Absorbable Suture 2/0 With 1/2 Cir Rb Needle Size:2/0 40Mm Length 90Cm-Polyglycolic Acid (Pga)Pack Of 12 Foils , Syringe With Needle(10Ml Each),Needle Disposable , Syringe With Needle(1Ml Each),Needle Disposable , Syringe With Needle(20Ml Each),Needle Disposable , Syringe With Needle(2Ml Each),Syrings Disposable , Syringe With Needle(3Ml Each),Syrings Disposable , Syringe With Needle(5Ml Each),Needle Disposable , System For Delivering Saturated Atomized Steam For Decontamination Of Surfaces , T Handle & Ss Chuck Large , T Handle & Ss Chuck Small , Tbw Ss Wires No. 18, 20,22 No. , Themacol Box (25Cmx21cm) , Thermacol Box(Size 9X6x6) , Thermometer Manually For Fever Tamprature , Thread Real For Suture Cotton , Three Layer Surgical Mask(Box Of 100 Mask) Disposable , Tips For Auto Pippetes 10 To 100 Micro Litres , Tissue Roll Paper (13Cm) , Toilet Brush Super Quality , Toilet Cleaner Compound , Tonometer Schiotz , Torch Plasic Body With Three Cell Isi Market Medium , Torch Plasic Body With Two Cell Isi Market Medium , Tourniquet With Belt(Mfg By Precious Life Care Pvt Ltd)(Good Quality Pairs) , Towel Clips Medium , Towel Clips Small , Towel Mayo Forcep Size 8 To 15 , Tri Sodium Citrate , Troch Chargable Electric Led Large , Troch Chargable Electric Led Midium , Troch Chargable Electric Led Small , Tuberculin Syringe , Tubercullin Vial 1.5 Tu P.P.T 5 Ml , Tubercullin Vial 10 Tu P.P.T 5 Ml , Tubercullin Vial 2 Tu P.P.T 5 Ml , Tubercullin Vial 5 Tu P.P.T 5 Ml , Typhoid Test Card Single Test For Widdal , Umbical Cord Clamps- Plastic Material (Box Of 100 Clamps) , Uric Acid (End Point) Pack Of 10X10ml , Urinary Catheter 2 Way Size 8 Foleys , Urinary Catheter 3 Way Size 16 Foleys , Urinary Catheter 3 Way Size 18 Foleys , Urinary Catheter 3 Way Size 20 Foleys , Urinary Catheter 3 Way Size 22 Foleys , Urinary Catheter Pediatrics Size 10 Foleys , Urinary Catheter Silkolatex 2 Way Sterile, Non Toxic Size 10 Foleys , Urinary Catheter Size 16 2 Way Foleys , Urinary Catheter(3 Way Size 12),Surgical Material Foleys , Urinary Drainage Bag (Paediatric)(100 Ml / Pc, Each) , Urinary Drainage Bag 2 Litre Cap With Non Return Valve (Eo Sterile) , Urinary Drainage Bag Cap With Non Return Valve (Eo Sterile)(2 Litre, Each) , Urine Caontainer Sterile 30Ml Pack Of 100 , Urine Collection Bag Adult Standard Company , Urine Collection Bag Chlild Standard Company , Urine Collection Bag Neonatal 50 Ml Standard Company , Urine Container 5Ml Disposable (50 Per Pkt) , Urine Pan Female With Cover (Made Of Stainless Steel) , Urine Pan Male With Cover (Made Of Stainless Steel) , Vaginal Speculam Ss Cusco Large , Vaginal Speculam Ss Cusco Medium , Vaginal Speculam Ss Cusco Small , Vdrl Shaker , Ventilator Neoatal & Pediatric - Volume Cycle Ventilator, Microprocessor Based Assisted Controled Short Term For Prolonged Ventilation Can Be Provide, Volume Delivery 20 Ml To 2000 Ml Cmv, Simv, Asb, Peep, Cpap Modes Easy To Handle And Operational, Electrically Operated, Air Compresson Should Be Provided Along With The Ventilator Miounted On Same Trolley, Nebulizer & Humidifier Both Adult And Pediatric, Ups System And/ Or Battary Backup For Compressor And Ventilator, Adult, Pediatric And Neonatal Breating Cicuits (Each) Alarms Display Facillity, Fio2 Dispaly Digital Display- All Set Parameter Should Be Display Automatically , Vicryl Suture Polyglactin 30 Mm 1/2 Circle Round Body 90 Cm Size 1/0(12 Foils/ Pkt), , Vicryl Suture Polyglyconic Suture 110 Cm No.2-0 Pack Of 12 Foils , Vicryl Suture Polyglyconic Suture 190 Cm No.1-0 Pack Of 12 Foils , Viscoelastic Material - Made By Reputed Company Guaranted Eto Sterlized, Prefilled Glass Syring 3Ml , Visiter Chair Three Seater Mettalic With Handle (Ss) , Voltage Servo Stabilizer Three Phase 50 Kva , Vtm - Hi - Media With 2 Swab : (For Swine Flu) Vtm Standard Kit(3Ml Vial With 2 Regular Swabs) , Wall Fan -18 Complete & Instaltion Charge (Standardisi/Iso Reputed Company) , Wall Fan -24 Complete & Instaltion Charge (Standardisi/Iso Reputed Company) , Wall Thermometer , Warm Sleeping Bag For Neonates , Washing Solution500 Ml All Modelconc , Waste Matarial Drum Swing Model 30 Ltr. , Waste Matarial Drum Swing Model 60 Ltr. , Water Bath , Water Cooler 150X150ltr Isi Market , Water Cooler 20X40 Ltr Isi Market , Water Cooler 40X80 Ltr Isi Marked , Water Cooler 60X120ltr Isi Marked , Water Cooler With Dispenser (20 Litre) Isi Mark , Water Test Kit For Ph 400 Kit Paking , Webcamera 10 Mega Pixel , Weghing Machine 1 Kg To 10Kg , Weighing Machine (1Gm To 100Gm) , Weighing Machine 1 Kg To 100Kg , Wet Mop Complete , Wheel Chair With Hand, Foot And Neck Rest Ss, , White Phynle Compound , Wiper Medium Size , Wiper Standard Size , Wire Passser Small , Wooden Stick/Broom Stick (8Inches) , X-Rayfilm 8 Inch X 10 Inch , X-Ray Cassets With Screen Size 10X12 , X-Ray Cassets With Screen Size 12X15 , X-Ray Cassets With Screen Size 8X10 , X-Ray Cassets(6.5X8.5) , X-Ray Cassets(8X10) , X-Ray Chest Stand , X-Ray Developer Powder (13.5 Ltr) , X-Ray Developer Powder (22.5 Ltr) , X-Ray Developer Powder (9 Ltr) , X-Ray Film 10 X 12 (50 Sheets/Pack) , X-Ray Film 12 X 12 (50 Sheets/Pack) , X-Ray Film 12 X 15 (50 Sheets/Pack) , X-Ray Film 14 X 14 (50 Sheets/Pack) , X-Ray Film 14 X 17 (50 Sheets/Pack) , X-Ray Film 6.5 X 8.5(50 Sheets/Pack) , X-Ray Film 8 X 10 (50 Sheets/Pack) , X-Ray Fixer Powder (Bromex Acid Fixer With Hardner) ( 22.5 Ltr/Pkt) , X-Ray Fixer Powder It Shall Be Powder Fixer To Produce Clean Radiographs Available In Pack Size Size:- 9 Ltr , X-Ray Fixer: Powder It Shall Be Powder Fixer To Produce Clean Radiographs Available In Pack Size Size:- 13.5 Ltr , X-Ray Grid 12X15 , X-Ray Grid 8X10 , X-Ray Half File Glomer 6X15 , X-Ray Half File Glomer 6X17 , X-Ray Hanger Size 10X12 , X-Ray Hanger Size 12X15 , X-Ray Hanger Size 6.5X8.5 , X-Ray Hanger Size 8X10 , X-Ray Lead Number (A To Z & 0 To 9) , X-Ray Led Aprin Standard Size , X-Ray Led Gloves , X-Ray Steel Ka Tank 13.5 Lit. , X-Ray Steel Ka Tank 19 Lit. , X-Ray Table For Patient Examine , X-Ray View Box Double , X-Ray View Box Single , X-Ray View Box With Auto Sensor (Four Film) , X-Ray View Box With Auto Sensor (One Film) , Zigli Saw , Zipper Ploy Bag Size 4X4 , Zipper Ploy Bag Size 4X6 , Zipper Ploy Bag Size 9X6 , Zipper Poly Bag Size 5X3 , Zipper Poly Bag Size 6X5 , Zipper Polybag Size 10X8 , Zipper Polybag Size 8X6

BRR : 9468305 Tender For Rates For Material/Equipment Regarding Medical Gas Pile Line System And Modular Operation Theatre For Estimate Preparation. - Rates for Material/Equipmentregarding Medical Gas Pile Line System and Modular Operation Theatre for estimate preparation. 2 Medical Gas Pipe Line (Part-A) 3 Oxygen Manifold 4 SITC of 10 + 10 size main manifold complete with middle frame with chain for individual cylinder along with Non Return Valve for every cylinder.All header racks and cylinder tailpipes should be 230 bar rated. Cylinder header racks for oxygen service shall be provided with connections for bull nose cylinder connections. Cylinder racks shall be manufactured from powder coated steel and shall be designed to securely support cylinders of varying diameters. Tailpipes shall have gas specific connections to the manifold header with threaded connections. Manifold header racks shall incorporate hard-seat, polymer-free non-return integral with each cylinder connection point to maintain system in the event of tailpipe fracture and prevent backflow of gas into the high pressure cylinders. as per specification (Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make- Altos/Aktiv or Equivalent 5 Certifications: ISO 13485:2016,ISO 9001:2015, CE 6 Fully Automatic Oxygen Gas Control System 7 SITC of Fully Automatic Oxygen Control Panel for main Oxygen Manifold having constant flow output of over 2100 LPM or more at 55 to 60 psig Pressure. A test certificate shall be provided with each system detailing the results of the factory tests ,It should have halogen polymers free. It should have Digital 3.5’ colorful display. It should have Integrated & protected test point. Central regulators panel with cylinder headers each side. It should have headers which shall be complete with gas specific cylinder tailpipes. Pre-wired for alarm connection to BMS outputs. All components degreased for oxygen use .Average gas consumption indication (for not liquefied gases). Remaining gas volume indication (for not liquefied gases). It should have general maintenance indicator. It should have Pressure transmitters monitor both banks of cylinders & as per specification. (Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make- Altos/Aktiv or Equivalent 8 Oxygen Flowmeter with Humidifier 9 Essentia medical gas flowmeters are designed to measure and regulate flow.These are calibrated to specific gas & flow range. Oxygen flowmeter is intended for use with various delivery system when bubble/ micro bubble humidifier is attached downstream. These flowmeters are widely used in home care, health centers, district/ general/ regional hospitals, tertiary care, emergency vehicles etc. for administration of supplemental oxygen through nasal cannula, simple face mask,partial rebreathing mask, non re-breather mask, resuscitation mask etc. A passive process to humidify dry therapeutic gas (Category 3 Humidification) Micro Bubble Humidifier for Respiratory Therapy Patient connection port : Tapered hose barb suitable for 6 mm inner diameter plastic tubingMicro bubbles through humidifier for efficient humidificationPossible to integrate into an oxygen concentrator, sleep apnoea therapy equipmentOptimal RH achievable at various flow settingsAutoclavable at 121°C (249.8°F) for 5 minutes (Minimum 5 autoclave cycles)Over pressure safety valveNon-heated and reusableInlet connection port : DISS female adapter with chrome plated Brass nut embedded in ABS for hand-tighteningFlow : Up to 15 lpm @ 4 bar (58 psi)Construction material: Polycarbonate - shatter resistantCapacity - 240ml at max water level (Jar 450ml)Make- Altos/Aktiv or Equivalent 10 Emergency Oxygen Manifold 11 The oxygen cylinder manifold should comprise of two cylinder Banks which can accommodate 6 cylinders in each Bank (means 6+6) complete with copper tail pipes with bull nose fittings of RH External threading suitable for cylinder valves (Oxygen service) and Cylinder support system. Manifold should be suitable to withstand a pressure of 140 Kg/cm2, along with high pressure copper annealed tail pipes with Brass adapter suitable for Oxygen Cylinders and manifold. Top frame comprising of high pressure copper pipes of size 1/2I.D. x 15swg with high pressure brass fittings made of high tensile brass and connections through non- return valves. High pressure copper tail pipes, made of high pressure copper pipe of size 1/4I.D. x 15 swg.The middle and bottom frame to be provided to fit both round and flat bottom cylinders safely. The manifold should be tested (hydraulically) at 250kg / cm sq. The copper tail pipes are fitted to the individual non return valves of the cylinder manifold for easy removal of cylinders without disturbance to system operation. Make- Altos/Aktivor Equivalent 12 Fully Automatic Oxygen Gas Control System 13 SITC of Fully Automatic Oxygen Control Panel for main Oxygen Manifold having constant flow output of over 2100 LPM or more at 55 to 60 psig Pressure. A test certificate shall be provided with each system detailing the results of the factory tests ,It should have halogen polymers free. It should have Digital 3.5’ colorful display. It should have Integrated & protected test point. Central regulators panel with cylinder headers each side. It should have headers which shall be complete with gas specific cylinder tailpipes. Pre-wired for alarm connection to BMS outputs. All components degreased for oxygen use .Average gas consumption indication (for not liquefied gases). Remaining gas volume indication (for not liquefied gases). It should have general maintenance indicator. It should have Pressure transmitters monitor both banks of cylinders & as per specification. (Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make-Altos/Aktiv or Equivalent 14 MEDICAL NITROUS OXIDE SYSTEM 15 Nitrous Oxide Manifold 16 SITC of 4 + 4 size main manifold complete with middle frame with chain for individual cylinder along with Non Return Valve for every cylinder.All header racks and cylinder tailpipes should be 230 bar rated. Cylinder header racks for oxygen service shall be provided with connections for bull nose cylinder connections. Cylinder racks shall be manufactured from powder coated steel and shall be designed to securely support cylinders of varying diameters. Tailpipes shall have gas specific connections to the manifold header with threaded connections. Manifold header racks shall incorporate hard-seat, polymer-free non-return integral with each cylinder connection point to maintain system in the event of tailpipe fracture and prevent backflow of gas into the high pressure cylinders.. as per specification.(Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make-Altos/Aktiv or Equivalent 17 Fully Automatic Nitrous Oxide Gas Control System 18 SITC of Fully Automatic Control Panel for Nitrous Oxide having constant flow output of over 500 LPM at 4.2 Bar Pressure. Digital Fully Automatic Control Panel. It should fully complies and meets with the requirements of the NFPA-99 standards. It should be UL or ETL Listed. The manifold control panel shall consist of two bank regulators (dome bias) used to reduce the cylinder pressure to the two line regulators which in turn controls the final line pressure. The manifold has an intermediate and line relief valve that is internally connected to a common vent port, terminating into a 1/2 FNPT pipe. It should be fully automatic type and shall switch from “Bank in Use” to “Reserve Bank” without fluctuation in the final line pressure. After the switchover, the “Reserve Bank” shall then become the “Bank in Use” and the “Bank in Use” shall become the “Reserve Bank.” The control panel includes a line gauge, two bank gauges and incorporates six LED’s: two green for “Bank in Use,” two yellow for “Bank Ready” and two red for “Bank Empty” on the front of the cabinet. Input power to the manifolds is 110 to 240 VAC, 50-60 Hz& as per specification. (Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make- Altos/Aktiv or Equivalent 19 Emergency N2O System 20 SITC of 2 Cylinder Emergency Nitrous Oxide manifold with All header racks and cylinder tailpipes should be 230 bar rated. Cylinder header racks for oxygen service shall be provided with connections for bull nose cylinder connections. Cylinder racks shall be manufactured from powder coated steel and shall be designed to securely support cylinders of varying diameters. Tailpipes shall have gas specific connections to the manifold header with threaded connections. Manifold header racks shall incorporate hard-seat, polymer-free non-return integral with each cylinder connection point to maintain system in the event of tailpipe fracture and prevent backflow of gas into the high pressure cylinders using a high flow Preset Pressure Regulator as per specification.(Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make- Altos/Aktiv or Equivalent 21 MEDICAL CARBON DIOXIDE SYSTEM 22 CARBON DIOXIDE SYSTEM 23 The CO2 cylinder manifold should comprise of two cylinder Banks which can accommodate 4 cylinders in each Bank (means 4+4) for cylinder valves conforming to IS 3234 (CO2@ service) complete with copper tail pipes with fittings. Manifold should be suitable to withstand a pressure of 140 Kg/cm2, along with high pressure copper annealed tail pipes with Brass adapter suitable for Nitrous Cylinders and manifold. Top frame comprising of high pressure copper pipes of size 1/2I.D. x 15swg with high pressure brass fittings made of high tensile brass and connections through non- return valves.High pressure copper tail pipes, made of high pressure copper pipe of size 1/4I.D. x 15 swg.The middle and bottom frame to be provided to fit both round and flat bottom cylinders safely. The manifold should be tested (hydraulically) at 250kg / cm sq. The copper tail pipes are fitted to the individual non return valves of the cylinder manifold for easy removal of cylinders without disturbance to system operation. Each manifold should be provided with one terminal header and a NPT connection for the Automatic control panel. Make- Altos/Aktiv or Equivalent 24 Certifications: ISO 13485:2016,ISO 9001:2015, CE 25 Fully Automatic Carbon DioxideGas Control System 26 SITC of Fully Automatic Control Panel for Carbon dioxide having constant flow output of over 500 LPM at 4.2 Bar Pressure. Digital Fully Automatic Control Panel.The manifold control panel shall consist of two bank regulators (dome bias) used to reduce the cylinder pressure to the two line regulators which in turn controls the final line pressure. The manifold has an intermediate and line relief valve that is internally connected to a common vent port, terminating into a 1/2 FNPT pipe. It should be fully automatic type and shall switch from “Bank in Use” to “Reserve Bank” without fluctuation in the final line pressure. After the switchover, the “Reserve Bank” shall then become the “Bank in Use” and the “Bank in Use” shall become the “Reserve Bank.” The control panel includes a line gauge, two bank gauges and incorporates six LED’s: two green for “Bank in Use,” two yellow for “Bank Ready” and two red for “Bank Empty” on the front of the cabinet. Input power to the manifolds is 110 to 240 VAC, 50-60 Hz& as per specification. (Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Micro processor controlled switch-over is accomplished automaticallyAutomatically resets itself for next cycle when depleted bank is replenished. No manual resetting requiredDigital pressure indication for accurate readingPressure unit options: bar, psi & kg/cm Status indicatorsPressure Stabilizer for stable discharge pressure & flowVisual & Audible signalDesigned to suit CO2 for gas specific usageOptimized residual gasMake-Altos/Aktiv or Equivalent 27 Emergency CO2 System 28 The Emergency supply manifold shouldbe connected to downstream of the manifold control panel.The assemblyshould consist of 2 (two) cylinders connection supplying a manually adjusted regulator via a common header assembly. The delivery system is isolated from the main system by an isolation valve. Pressure gauges should indicate cylinder and delivery pressure & valves conforming to ISO 13485Make- Altos/Aktiv or Equivalent 29 MEDICAL VACUUM SYSTEM 30 SITC of MEDICAL VACUUM SYSTEM AS PER SPECIFICATION 31 Vacuum Pump : The arrangement should consist of 2 nos. of oil lubricated imported rotary vane vacuum pump. Each vacuum pump should have capacity of 5000 lpm with IEC Motor rating of minimum 10 HP @ 50 Hz or above. Vacuum pumps shall comprise of air cooled, oil lubricated rotary vane vacuum pumps suitable for both continuous and frequent start / stop operation at inlet vacuum vessels between 525 mm Hg and 700 mm Hg. The ultimate vacuum of pump shall be 0.1 mbar with gas ballast valve closed. The Vacuum Pump should be air cooled and oil lubricated rotary vane vacuum pumps designed for use in the field of high quality vacuum. It should be a robust construction, reliable operation, highly resilient carbon composite fiber vanes, Gas ballast valve. The pump should be having a 4 barriers system that avoids any oil leaks by doubling the 2 lip / shaft seals. Pump vanes shall be lubricated by a fully re-circulated and filtered lubricant supply. Also Pump design should include a lubricant separation system integral to the pump exhaust box consisting of no less than four stages of internally installed lubricant and smoke eliminators through which the exhaust gas stream must pass. This system shall consist of bulk separation, lubricant mist elimination, smoke elimination, synthetic lubricant baffle, and shall be capable of removing 99.9 percent of all lubricant and smoke particles from the exhaust gas stream. The unit should have extremely low vibration as per specification.(Mandatory submission--> 100% technical complaince sheet should be submitted with the technical bid from original manufacturer.)Make- multitech/hitachi/Anistaiwata or Equivalent 32 Vacuum Tank of 5000 liters water capacity.Make- multitech/hitachi or Equivalent 33 Bacterial Filter:Vacuum Filter (Bacteria Filter) of 100 cfm to 105 cfm – 3” Filter housing with drain flask.: It fully complies and meets with requirements of UK HTM medical standards. It should have BS 3928 sodium flame test certificate based on requirements of HTM standards.The bacteria filter should be designed for critical application involving removal of dry and wet dust, particulars, oil aerosol and water droplest, high efficiency glass fiber, fieece media from suction side of vacuum pump system. It should have efficiency of at least 99.995% when tested by sodium flame test and that should be according to BS 3928:1969. The Vacuum filtration efficiency should be in excess of 99.9999% as per HTM0201 & AS 2896 standards. The high efficiency medical grade filter element should have custom engineered filter media and deep pleat element technology provides minimal pressure loss and filtration efficiencies. It should have advanced filtration technology for Low pressure loss borosilicate glass microfiber-media and open cell reticulated foam pre-filtration layer captures particulates, bacteria and liquid aerosols reducing energy consumption and overall system costs. It should have corrosion protection Internal and external electrophoretic painting followed by a tough exterior polyester powder coating.It should have easily removable sterilisable drain flask and differential pressure monitor gauge. It should have push fit element design for quick and easy maintenance with unique push fit element design. It should have element end cap color black. It should have maximum temperature 60 degree centigrade (140 degree F). It should have element of E31140MV grade. It should have pipe size connection 1” = 105scfm and 180nm3/hr FAA. It should have pressure loss clean & dry = < 3kPa (30m/bar/0.44psig). It should have maximum working pressure 0.5barg(7psig. It should have manual drain valves and 250ml sterilisable glass drain flasks.(Maximum tolearance allowed will be only 10%).Smooth mobility.Sturdy trolley mounted on 5 castor base wheels.Operational when connected to centralized vacuum.Fast connection to the vacuum source.Various Vacuum Connector options.Controllable & Stable vacuum for procedure.Step-less vacuum regulation within the range.Gauge needle with anticlockwise movement .Vacuum trap with bacterial filter in series to protect.system networkDisposable hydrophobic filter element.Quick hassle-free replacement of bacterial filter.Switch toselect collection jar & quicksuction shut-off.Easy access to selector switch.90 degree angular interface connectors to push-fit catheters.Autoclavable Polycarbonate collection jars.Overflow prevention trap on each collection jar.Make- Tridentor Equivalent 34 Ward Vacuum Unit with Regulator, Collection Jar of 1000 ml with Bracket.Make- Altos/Aktiv or Equivalent 35 Theatre Vacuum Unit mounted on Trolley consisting of Vacuum Regulator with Gauge and 2 nos. of 4000 ml Polycarbonate.Make- Altos/Aktiv or Equivalent 36 Bacteria Filter (Plastic) for 100 ml Safety Trap before Vacuum RegulatorMake- Altos/Aktiv or Equivalent 37 COMPRESSED AIR SYSTEM 38 SITC of COMPRESSED AIR SYSTEM AS PER SPECIFICATION 39 Oil Free Scroll Air Compressor: The arrangement should consist of 2 nos.oil free scroll air compressor. It should be rated for 50 Hz, 3 Phase, 415 VAC power supply. Motor rating of each compressor should be 22 Kw & 30 Hp. Each scroll compressor should have a flow capacity of minimum 73 cfm (2070 LPM). The scroll air compressors shall be air cooled. Compressors shall be oil free scroll compressors suitable for both continuous and frequent start/stop operation having outlet pressure control range of 800 to 1000 kPa (8 to 10 bar). Each compressor shall have at least two individual scroll elements. The air quality shall be 100% oil free, certified ISO8573-1. The compressor shall have a sound insulating enclosure. Each scroll air Compressor should have an element consists of a fixed scroll shaped housing and a scroll shaped rotor. Air enters the compressor element through inlet opening. Once the air is drawn in, the orbiting scroll seals the inlet opening and forces the air into a continuously decreasing space. As scroll keeps orbiting, this process of compression is constantly repeated, resulting in discharging of oil free compressed air through outlet opening. Air is drawn through air filter and should be compressed by the compressor element of each compressor module. The compressed air is discharged via the check valve and a common air cooler. The cooling air is blown over the compressor element via a duct. A separate electric fan provides cooling air for the common air cooler. Each set of compressor modules has its own common aftercooler with an electric fan. The separator on compressors without integrated dryer has an automatic condensate outlet and a manual drain valve. The air compressors with integrated dryer, the dryer is equipped with a trap with an automatic condensate outlet and a manual drain valve. Each compressor element is protected by a sensor in the outlet pipe. The sensor is connected to the electronic regulator. Make- multitech/hitachi/Anistaiwata or Equivalent 40 Air Receiver of 5000 Liter Water Capacity (designed to withstand pressure of 10 Bar) with Auto Drain ValveMake-multitech/ hitachi or Equivalent 41 Medical Breathing Air Dryer- 375 SCFM - Medical air dryer heatless with purification modules are intended to provide a continuous supply of medical quality air conforming to the European Pharmacopoeia medicinal air monograph (ref. 1238), for respiratory use in healthcare facilities. The system shall be duplex such that the supply is maintained in single fault condition. Medical compressors shall be provided such that the specified volumetric flow is achieved without standby or backup systems running. Purification Module : The duplexed filter and dryer module shall incorporate high efficiency oil coalescing filters, heatless regenerative desiccant dryers, activated carbon filters and bacterial filters. The performance of the filters shall be according to below specifications: Oil coalescing high efficiency filter: mass efficiency of 99,92%, tested according to ISO 8573-2 & ISO 12500-1; Activated carbon filter: max remaining total oil content of 0,003 mg/m³, tested according to ISO 8573-5 & ISO12500-2;Bacterial filter: particle count efficiency of 99,98% at MPPS=0.06μm, tested according to ISO 12500-3. Dryer Purge Control : The dryer control system shall incorporate a Purge Saver Energy Management system that freezes the regeneration of the desiccant once adequate dew point is reached in the inactive tower. Only when the dewpoint level in the active tower deteriorates to an unacceptable level will the intelligent controller switch towers.Coarse coalescing filter of 375 SCFM (one working and one as stand by) flow capacity: It should have flow-optimized design for advanced filter head design for optimized flow performance. It should have flexible installation Modular design and accessible fixings enable simple close coupling assembly. It should comply with air quality standard ISO 8573-1: 2010. It should have profiled bowl design and push fit elements ensure quick and for reliable maintenance. It should have corrosion protection Internal and external electrophoretic paint finish followed by a tough exterior polyester powder coating. It should have color coded element end caps of red color for easy and accurate grade identification. It should have element of E30612 grade.It should have particle retention of up to 99.999%, and significantly reduced pressure loss. It should have particle removal 1 micron. It should have maximum particle size class 2 micron as per ISO 8573-1: 2010 . It should have maximum oil content 3 micron ISO 8573-1: 2010.It should have maximum oil carryover at 68 degree F (20degree centigrade) = 0.3ppm (0.3mg/m3). It should have pressure loss clean & dry = 0.8psi (55m/bar). It should have pressure loss saturated = 1.8psi (125m/bar). 42 Fine coalescing filter of 375 SCFM (one working and one as stand by) flow capacity : It should have flow-optimized design for advanced filter head design for optimized flow performance. It should have flexible installation Modular design and accessible fixings enable simple close coupling assembly. It should comply with air quality standard ISO 8573-1: 2010. It should have profiled bowl design and push fit elements ensure quick and for reliable maintenance. It should have corrosion protection Internal and external electrophoretic paint finish followed by a tough exterior polyester powder coating. It should have color coded element end caps of blue color for easy and accurate grade identification. It should have element of E30612 grade.It should have particle retention of up to 99.999%, and significantly reduced pressure loss. It should have particle removal 0.01 micron. It should have maximum particle size class 1 micron as per ISO 8573-1: 2010 . It should have maximum oil content 1 micron ISO 8573-1: 2010.It should have maximum oil carryover at 68degree F (20degree centigrade) = 0.01ppm (0.01mg/m3). It should have pressure loss clean & dry = 1.2psi (85m/bar). It should have pressure loss saturated = 1.8psi (125m/bar). Activated Carbon Filter of 375 SCFM (one working and one as stand by) flow capacity: It should have flow-optimized design for advanced filter head design for optimized flow performance. It should have flexible installation Modular design and accessible fixings enable simple close coupling assembly. It should comply with air quality standard ISO 8573-1: 2010. It should have profiled bowl design and push fit elements ensure quick and for reliable maintenance. It should have corrosion protection Internal and external electrophoretic paint finish followed by a tough exterior polyester powder coating. It should have color coded element end caps of black color for easy and accurate grade identification. It should have element of E30612 grade.It should have particle retention of up to 99.999%, and significantly reduced pressure loss. It should have particle removal 0.01 micron. It should have maximum particle size class 1 micron as per ISO 8573-1: 2010 . It should have maximum oil content 1 micron ISO 8573-1: 2010.It should have maximum oil carryover at 68degree F (20degree centigrade) = 0.003ppm (0.003mg/m3). It should have pressure loss clean & dry = 1.7psi (115m/bar). 43 Fine Dust Filter of 375 SCFM (one working and one as stand by) flow capacity : It should have flow-optimized design for advanced filter head design for optimized flow performance. It should have flexible installation Modular design and accessible fixings enable simple close coupling assembly. It should comply with air quality standard ISO 8573-1: 2010. It should have profiled bowl design and push fit elements ensure quick and for reliable maintenance. It should have corrosion protection Internal and external electrophoretic paint finish followed by a tough exterior polyester powder coating. It should have color coded element blue color end caps for easy and accurate grade identification. It should have element of E30612 grade.It should have particle retention of up to 99.999%, and significantly reduced pressure loss. It should have particle removal 0.01 micron. It should have pressure loss clean & dry = 1.5psi (100m/bar). Make- Trident or Equivalent 44 Pressure Reducing Station for 4 Bar: The compressed air system shall be supplied with duplex pressure regulator arrangement to regulate the line pressure from 10 bar to 4 bar for medical air. Adequate number of isolation valves should be provided to isolate each regulator separately during maintenance without shutting down the entire compressed air system. Presssure Regulators should be 28 bar rated. Brass pressure relief valve, 1/4 thread BSP should be provided after the regulator. Pressure Gauge of range 0 to 11 bar to be provided to monitor line pressure. Relief Valve Settings : Nominal 4 bar stations - 5.5 bar relieving.The Pressure Reducing Station should be capable of delivering minimum 10000 LPM flow.It shall be duly CE marked to the Medical Device Regulations and under this regulations, med gas products are classified as Medical Devices. 45 Pressure Reducing Station for 7 Bar: The compressed air system shall be supplied with duplex pressure regulator arrangement to regulate the line pressure from 10 bar to 7 bar for surgical air. Adequate number of isolation valves should be provided to isolate each regulator separately during maintenance without shutting down the entire compressed air system. Presssure Regulators should be 28 bar rated. Brass pressure relief valve, 1/4 thread BSP should be provided after the regulator. Pressure Gauge of range 0 to 11 bar to be provided to monitor line pressure. Relief Valve Settings : Nominal 7 bar stations - 9 bar relieving.The Pressure Reducing Station should be capable of delivering minimum 4000 LPM flow.It shall be duly CE marked to the Medical Device Regulations and under this regulations, med gas products are classified as Medical Devices. 46 SITC of Medical Gas Outlets- 47 Probes are crucial for gas specific and stable connection. These are used to connect medical gases and vacuum devices to outlets / terminal units of MGPS distribution network.Make- Altos/Altos/Aktiv or Equivalent 48 FeaturesSmooth quiet action.Safe keying configurations.Gas specific ISO 32 colour coding.Firm locking of connector / probe.Strong, positive and secure connection.Corrosion-free and material compatibility.Reliable and safe dispense of gases & vacuum.Pipe stub end flared to align drop pipe and to avoid butt joint. 49 Oxygen 50 Air-4 51 Air-7 52 N2O 53 AGSS 54 Vacuum 55 CO2 56 Certifications:ISO 13485:2016 – Medical devices,ISO 9001:2015 57 MISCELLANEOUS ITEMS 58 SITC of Common Electrical Control Panel for Compressed Air System, Vacuum System & AGSS as per requirementcomplete with plant room wiring. 59 SITC of Degreased Medical Grade Copper Pipe as per EN 13348 :2018. BSI Kite Mark certified. CE Certified. Third Party Inspection by TUV or Lloyds Registrara AsiaMake- Altos/Altos/Aktiv or Equivalent 60 Installation of piping should be carried out as per international standards with utmost cleanliness. Only pipes, fittings and valves which have been degreased as per International standards should be used . Pipe fixing clamps for upto 28mm diameter. Pipes should be non ferrous suitable for the diameter of the pipe. For the pipes of the sized above 28mm rigid metallic hanging or cemented supports to be used. 61 The main lines to the building to be taken overhead through metallic poles or through underground ductswith inspection removable slabs,All pipe joints should be made using inert gas fluxless brazing method.Alljoints should be of copper to copper and should be brazed by silver brazing filler material without flux while being brazed joints shall be continuously purged with oil free dry nitrogen to prevent the formation ofcopper oxide on the inside surface of the joint.All pipes should be installed without springing or forcing.All pipes shouldprotected against mechanical injury in a manner satisfactory to authorities havingjurisdiction. 62 Test: After erection, all the new pipes cleaned or purged with the help of dry nitrogen gas.Complete system should be tested with dry nitrogen at 2 times of working pressure for 24 hours. 63 Painting: All existing and proposed exposed pipes/should be painted with two coats of Synthetic enamel paint & color codification as per international standards.All concealed pipes to have gas identification bands / labels at appropriate distance.Similarly all pipes which need embedding in the wall should be tested/painted/labeled and properly insulated. 64 Solid drawn, seamless, deoxidized, non arsenical, half hard, tempered and degreased materials conforming to BS: EN 13348. 65 All copper pipes will beUL certified for medical use before dispatch and the pipe will be delivered plugged or capped at both ends. 66 108 mm OD X 1.5 mm thick 67 76 mm OD x 1.5 mm thick 68 54 mm OD x 1.2 mm thick 69 42 mm OD x 1.2 mm thick 70 35mm OD x 1.2mm thick 71 28 mm OD x 1 mm thick 72 22 mm OD x 1 mm thick 73 15 mm OD x 1 mm thick 74 12 mm OD x 0.7 mm thick 75 SITC of Medical Gas Digital Area Alarm System 76 Microprocessor based digital LCD alarmHighly visible 7 (178 mm) LCD screenPressure sensing through piezoresistive sensing technologyAlarms can be monitored audio-visualTouch screen operationComprehensive monitoring of all the medical gas alarm panelsData display at a central monitoring station Features-Alarm status will be visible through ethernet port on master alarmPressure Equipment Directive 2014/68/EUDigital Flow Care Alarm Management of Medical Gas Pipeline SystemReal time updating of statusOperational parameters i.e. high and low level canbe set “in-situ” to suit requirement in an area 2Programmable pressure unit display (bar, kg/cm & mmHg)Audio mute optionDesigned to serve 2, 3, 4, 5 & 6 gases including VacuumNIST connection for Gas inputPowered by 220V AC to 24V DC external adapterMake-Altos/Aktivor Equivalent 77 Conforms to: IS / ISO 7396 - 1 : 2016 + A1 : 2017HTM 02-01 Part A, IS / ISO IEC 60601 - 1 : 2015 + A1 : 2020Certifications:ISO 13485:2016 – Medical devices – Quality Management SystemsISO 9001:2015 - Quality Management Systems 78 6 - Gas (O2, N2O, Med Air-4 Bar, S Air-7 Bar, Vacuum & CO2) 79 5 - Gas (O2, N2O, Med Air-4 Bar, S Air-7 Bar & Vacuum) 80 4 - Gas (O2, N2O, Med Air-4 Bar & Vacuum) 81 3 - Gas (O2, Med Air-4 Bar & Vacuum) 82 2 - Gas (O2 & Vacuum) 83 SITC Of Area Valve Service Unit with Valve & Gauge 84 The importance of full bore ball valves is to reduce pressure drop to almost negligible in the pipeline distribution system so that the designed pressure is available at the outlet point. Ball Valves are used to start or stop a flow. In Medical Gas Pipeline System (MGPS), the valves are normally kept open i.e. allow the gas to flow unless it is required to shut-off the gas supply for scheduled maintenance or emergency situation 85 Features-Operational parameters can be set in-situDigital pressure unit display options -psi / bar or kg/cmDigital & illuminated LED display of “Normal”, “High” & “Low”Microprocessor based moduleHighly accurate “Heavy Duty” pressure transducerPowder coated aesthetically designed enclosureEnclosure separable from the base for ease of installationReusable lock assemblyAudio mute optionPED: 2014/68/EU certified full port Ball Valve (PN 30)Long extension copper pipes to connect MGPS networkFront door opens up vertically for comfortable accessDesigned to serve 2, 3, 4 & 5 gas moduleSuitable for all medical Gases & VacuumMake- Altos/Aktiv or Equivalent 86 6 Gas Service (O2, N2O, Med Air-4 Bar,Air-7 Bar, Vacuum & CO2) 87 5 Gas Service(O2, N2O, Med Air-4 Bar, Air-7 Bar & Vacuum) 88 4 Gas Service(O2, N2O, Med Air-4 Bar & Vacuum) 89 3 Gas Service (O2, Med Air-4 Bar & Vacuum) 90 2 Gas Service(O2 & Vacuum) 91 SITC of Degreased Medical Lockable Ball Valve with Pipe line assembly 92 Pre piped single port) for size upto 2 (for 54mm copper pipe): Pre Piped Degreased Ball Valve with pipe extension. It should be full-port design. It shouldbe blow-out proof stem. It should be lockable valve. The Valve shall be 3 piece ball-type design with a bronze body and chrome plated brass ball for sizes 1/2” to 4”. Seats shall be Teflon (TFE) and seals Viton for 1/2” - 4” valves. A blow-out proof stem shall be used and the valve shall have a maximum pressure rating of 600 psi [4,137 kPa].Valves shall be operated by a lever-type handle requiring only a quarter turn from a fully open position to a fully closed position. Valves shall be designed in such a manner that it can be “swung-out” during installation so as to prevent damage due to heat transfer during the brazing operation. Each valve assembly shall be washed and degreased for medical gas service. The valve shall be supplied in a sealed plastic bag to prevent contamination prior to installation.Make- Altos/Aktiv or Equivalent 93 12mm 94 15 mm 95 22 mm 96 28 mm 97 35mm 98 42 mm 99 54 mm 100 108mm 101 SITC of Bed Head Panel aluminum powder coated with mininum 3 channel and 3 duct with separate partition rows and built in aluminum railMake- Altos/Aktiv or Equivalent 102 Bedhead panel for Low Equity Ward Areas, 1500mm length, with provision of Gas outlets & provided with electrical sockets & accessories complete 103 Horizontal Bed Head Panel – For 2 Gas Service (Oxygen & Vacuum) 104 Horizontal Bed Head Panel – For 3 Gas Service (Oxygen, Med Air-4 Bar & Vacuum) 105 Horizontal Bed Head Panel – For 3 Gas Service (Oxygen, N2O & Vacuum) 106 Horizontal Bed Head Panel – For 4 Gas Service (Oxygen, N2O, Med Air-4 Bar & Vacuum) 107 Special FeaturesInnovative design – Efficient, simple & accessibleVersatility – Configurable & economic adaptation of various servicesAesthetics – High quality surface finish, epoxy coated to RAL 7035(Textured)Smooth profile – Minimize adherence of dust particlesExtruded aluminium frame – Rigidity & ease of interior accessability to serviceSeparate compartments - for LV, ELV and Piped GasNon-disruptive maintenance of BS Outlet - Shut down of line gas is avoidedOption of concealed gas connections and choice of outlet 108 Application AreasInnovative design – Efficient, simple & accessiblityVersatility – Configurable & economic adaptation of various servicesAesthetics – High quality surface finish, epoxy coated to RAL 7035(Textured)Smooth profile – Minimize adherence of dust particlesExtruded aluminium frame – Rigidity & ease of interior accessability to serviceSeparate compartments - for LV, ELV and Piped GasNon-disruptive maintenance of BS Outlet - Shut down of line gas is avoidedOption of concealed gas connections and choice of outletAdult in-patient wards/ General WardsResuscitation RoomsPost-anaesthesia areaEmergency Admission WardsDialysis Stations 109 Configuration : 5 Outlets & 6 Multi Standard 220V AC sockets, 1 each RJ11 Telephone socket & RJ45 Data Socket and provision of protective earth (Earthing) 110 Modular Operation Theatre (Part-B) 111 WALL AND CEILING MODULAR PUF PANEL 112 The panels shall be made of durable and uniform material that shall be easy to clean and extremely hygienic. Operation theatre shall not have any sharp edges, corners and shall not support bacteriological or fungicidal growth and shall be resistant to most chemicals, commonly used in Hospital Departments. Joints in the panels in the operation theatre shall be sealed. The function of sealing shall assure an airtight environment in the room and eliminate services to prevent dust accumulation.PUF Panel with an overall thickness of 50 mm for wall and 30 mm for ceiling, made of 0.8mm (make-Tata/jindal)GI Front sheet and 0.6mm PPGI back wall with infill of PUF at 40 kg/m3 (40D)which is necessary for mechanical strength. Panels shall be mounted on a structure made of galvanized steel and shall enable the distribution of medical gases, electricity, sewerage inside the wall.PUF Panel as above has better thermal efficiency and thus saving on energy cost. Proposed system shall be installed at site without any welding.The partitions shall not have corners; adjacent surfaces shall be molded flush.Upper wall element shall have sufficient height to reach the lower edge of the prefabricated ceiling. All the sharp edges and corners should be chamfered to avoid bacterial contamination.The individual ceiling panels shall use the tongue and groove technology for joining two panels, no welding shall be allowed,provides a seamless sub-structure, which is then sanded smooth finished with Metal Putty and then painted using imported anti-fungal paint to give a smooth, non-porous seamless finish and without corners by providing coving on floor as per standard.It is resistant to chemicals used in Operation Room for moping and fumigation repeatedly.Make-Jindal/Tata or Equivalent 113 WALL AND CEILING MODULAR PUF PANEL-SS304 114 The prefabricated Operating Room should be of SS Sandwich as per its latest standards. SS Sandwich : It should have at least min. 0.8 mm 304 Grade Stainless Steel on front side and 0.5mm PPGI back side . The sandwich panel shall have a core consisting of rigid polyurethane foam, injected under high pressure, with a minimum density of 40 kg/m3. Cladding structure insulated stainless steel wall panels with total panel thickness 50 mm for wall and 30mm for ceiling.The individual wall panels shall use tha tongue and groove technology for joining two panels, no welding should be allowed. The gaps between panels shall be suitably filled with metal filler and sanded flush. Stainless steel plate finished to fine grain surface, treated properly to take antifungal paint panelingshould be easy to maintain, durable, antistatic / conductive and fire retardant. Clearance between inner panel and outer wall should be sufficient to allow the maintenance personnelfor service. This closed space should be flushed continuously to eliminate dust and bacterial accumulation.It should have minimum number of junctions. The junction should be seamless and should be sealed with suitable sealants. Third party test certificate for SS from material testing lab. (Govt. authorized)required.Make-Jindal/Tata or Equivalent 115 ANTI-FUNGAL PAINTING 116 Anti microbial Paint for Different Areas antibacterial Paint on wall and ceiling panels Inside OT work.Anti-Microbial Protection: These product hygiene coatings start the biocidal action as soon as the microorganism land on the surface, and prevents the growth of mould, bacteria and yeasts for at least 5 years.Minimum three coats of Anti Fungal/Bacterial Paint, glaze or equivalent to a minimum dry thickness of 300 microns to give smooth , non-porous finish without any corners.It will also be resistant to the chemicals used in Operation Room for Moping & Fumigation repeatedly. This Hygiene coating are independently tested by leading universities to demonstrate resistance.Make-SKK/ Jotun or Equivalent 117 PLENUM LAMINAR AIR-FLOW 118 Supply and installation of Plenum LAMINAR FLOW- Plenum Box Ceiling mounted systemwith unidirectional airflow, SPECIFICATIONS-PLENUM UNIT - The complete unit factory designed and manufactured with proper air-sealing. It seamlessly integrates with OT ceiling mounted equipment.Plenum size- 2400 x 2400mm with aluminium material.Diffusers are made of SS304 punched/perforated sheet for unidirectional diffusion air. The complete unit factory designed and manufactured with proper air-sealing.It seamlessly integrates with OT ceiling mounted equipment.The material used is non-corossive as per standard guidelines such as Aluminium.Make-Jindal/Tata or Equivalent 119 Hepa Filters- 120 The filter hosing on either side houses provided with HEPA minipleate H13/H14 filters.The system has a reliable filter efficiency, filters are designed to remove particles and germs with the use of H13/H14 filters retaining 99.97 % of the particles and germs.Frame : Aluminium Mini Pleat Size- 610x610x125mmMOC of the Media : Micro Fibre Glass micro drawn grid Separators : continuous Gasket: Food GradeMPPS average efficiency: > 99.95% 3 Micron D Efficiency: 99.97% down to 0.3µ.Maximum Operating Temp : 60 degree CelsiusMake- Thermadyne or Equivalent 121 ANTI-STATIC VINYL FLOORING: 122 SupplyandinstallationofImportedVinylFloor:SeamlessantistaticconductiveESDvinylflooringsystem,2mmthick, with perfectly curved flush covings and copper strips for earthing, all joints welded properly including wall scatting.SPECIFICATIONS:- Flooringinoperationtheaterroomwii beseamless withperfectly curvedflash-covings,resistance tomechanicalstressanddynamicloadsandhavingESD/EMI(Conductive)protectioncharacteristics,2mmthick, washablevinyl.Flooring is a static-conductive,flexible homogeneousvinyl floor covering withan electricalresistance of 5x10^4 123 SELF LEVELLING MATERIAL. 124 The SLC should be of Portland cement-based, It should be self-leveling underlayment formulated with a special blend of polymersusedtolevelandsmoothinteriorconcrete,terrazzo,ceramicandquarrytile,epoxycoatingsystems,metal andnon-watersolubleadhesiveresidueonconcretepriortotheinstallationoffinishedflooring–on,aboveorbelow grade.TheSLCshouldprovideadurable,flat,smoothfloor surfacewithminimumlabor andinstallationtime.Itshould be pourable or pump-able when mixed with water and should seek its own level to produce a smooth, flat, hard surface. 125 OPERATION THEATRE CONTROL PANEL: 126 Supply and installation of Membrane type 6 services OT control panel , with distribution box mounted flush in the theatre wall, comprising of the following:The surgeon control panel should meet Electrical safety codes for high & low voltage system, wired to the current IEE regulations.The room Surgeon’s control panel should be modifiable with changing technology& equipment in operating environments. Control Panel will be user friendly & ease of operating & maintaining purpose.he panel should be “Membrane” type; configured to incorporate all the services that operation room staff required. The fascia should be made with superior quality UV resistance membrane with sterilization feature.The Panel should contain 6 or 9 service tiles as below:1. Time Day Clock. 2. Time Elapse Day Clock. 3. General Lighting System.4. Medical Gas Alarm Panel. 5. Hand Free Telephone set with memory.6. Temperature & humidity indicator with controller.7. HEPA Filter Status module. 8. Room Pressure Indicator. 9. Music control. Time day clock should be digital type & clocks having high brightness characters. Time Elapsed Day Clock should be digital type & clocks having high brightness characters.Temperature indicator should indicate the room temperature which should be connected to the local pressure switches of Air-Conditioning System. Indicators should be digitaltype & clocks having high brightness characters, not less than 30 mm in height. Central Lighting system should incorporate all the necessary controls of the lighting. system inside the theatre.The medical gas alarm should indicate High, Normal & Low gas Pressure for each gas service present in the operating system & should have an audible buzzer with mute facility. Pressure sensors should be connected to MGPS for monitoring the pressures.A hand free set Telephone System should be incorporated in the panel with memory type card.The control panel should be designed for front- access only. All internal wires should beMake- Altos/DGline or Equivalent 127 Distribution Board outside OT 128 Electrical Distribution Board will have all high voltage equipment should be installed in a separate enclosure. The remote cabinet should house the operating transformers, light control relays, electrical distribution equipment and circuit protection equipment for all circuits withinthe operating theatre. All internal wiring should terminate in connectors with screw mounted, on a DIN rail. Individual miniature circuit breakers will protect all internal circuits. All high voltage equipment should be installed in a separate enclosure.All internal wiring should terminate in connectors with screw & clamp springConnections of the clip- on type mounted, on a CE/ / ICMED9001/ ICMED13485 approved rail & labeled with indelible proprietary labels.Individual fuses or miniature circuit breakers should protect all internal circuits. 129 LED PERIPHERAL/GENERAL LIGHTS: 130 Recess mounted sealed IP54 Protocol, non-hygroscopic peripheral lights ( 1 x 2 ) having compact high glow low wattage LED lighting system. These lights are having electrical safety code for high & low voltages.The luminaries for recess mounting in operation theatres should flush with the ceiling based on LED, with optical anti- glare system for individually adjustable light distribution.Luminaries cover made of highly-resistant, disinfectant-proof acrylic diffuser with white coated steel frame.Closing devices are integrated automatically in the electrical safety control without lines having to be connected to the luminaries housing. Luminaries’ body made of sheet steel, white, powder-coated, supplied ready for connection optionally for individual or group with power saving technology. Luminaries with protection IP 65, and protection class I,230 V,50 Hz.Recess frames for the gas-tight installation of clean-room luminaries in IP 65 in suspended ceilings.Frame made of extruded aluminium profile, white, powder-coated, able to be put together to form a rigid, continuous frame by means of plug and screw connections.Control equipment for the general lighting and the light dimming should be provided in the theatre Control Panel.Make-Altos/DGline or Equivalent 131 LED X-RAY VIEW PANEL: 132 TwoPlateX-RayViewScreenwithflickerfreeilluminationhavingimportedLEDsystemforuniformilluminationand operated by X-ray film .Thesystemhavingelectricalsafetycodesforhigh&Lowvoltagesystem.Itshouldbedesignedtoprovideflickerfree luminance for the film viewing purpose.It should be installed flushed with the theatre wall for hygiene and ease of cleaning.Make-Altos/DGline or Equivalent 133 MAGNETIC LISTING WRITING BOARD: 134 MagneticWritingBoard of size940x 640x50mmcomprisesof aflushmounted,1.50mmthick,whitelaminate board, bonded toa 10 mm high density fibreboard sheet for additional rigidity.The writing unit should comprise of flush mounted white laminate board, be opened to create a wall mounted writing surface within the operating room. The white board should be constructed from white laminate board.Make- Altos/Dgline or Equivalent 135 AUTOMATIC HERMETICALLY SEALING SLIDING DOOR -1500mmX2100mm 136 Automaticoperated Hermettically Slidingdoor with High Pressure Laminate on both side, Door size (1500mm wide2100mmheight)completewithdoubletoughnedglassvisionwindowof300mmx300mm withinanaluminum extrusionhighqualityframecompletewithrequiredaccessories.Thedoorframesconsistofreinforcedplasterboard panelsfacedwiththesamelaminateasthedoorandwillbeedgedwithanaluminiumextrusionandwithconcealed fixings that are adjustable during installation to ensure sealing.• Environment temperature should be -20°C to +55°C.The doorframe should be made of high quality anodize aluminum and the door panel should be made of compact laminate that can withstand high abrasion. To ensure efficient sealing of the doors frames should be provided. They will consist of reinforced plasterboard panels faced with the same laminate as the doorsVision panels, 300mm X 300 mm should be provided in the doors.The Door should be mounted and should complete with all necessary accessories i.e.Door closer, D type SS Door HandleMake-Metaflex/Doormedor Equivalent 137 HERMETICALLY SEALING HING DOOR-900mmX2100mm 138 Manually operated Hermettically Semi- sealed Hing door with HighPressure Laminateon bothside, Door size (900mm wide x 2100mm height) complete with double toughned glass vision window of300mm x300mm andsmooth effortless doorcompletewithrequiredaccessories,fixedfirmlytothewall.Thedoorframesconsistofreinforcedplasterboard panelsfacedwiththesamelaminateasthedoorandwillbeedgedwithanaluminiumextrusionandwithconcealed fixings.• Environment temperature should be -20°C to +55°C.The doorframe should be made of high quality anodize aluminum and the door panel should be made of compact laminate that can withstand high abrasion. To ensure efficient sealing of the doors frames should be provided. They will consist of reinforced plasterboard panels faced with the same laminate as the doorsVision panels, 300mm X 300 mm should be provided in the doors.The Door should be hinge mounted and should complete with all necessary accessories i.e.Door closer, D type SS Door Handle. The door track is constructed from an aluminium extrusion, fixed firmly to the wall. Nylon runner guides are fixed to the floor in such a way that they do not obstruct trolley movement through the door.Make-Metaflex/Doormed or Equivalent 139 CORNER GRILLS 140 Aluminium corner grills are used to air exhaust at all four corners.size of grill will be 600mmX400mm.Duly powder coated extruded aluminium linear horizontalfixed bar with normal 15 deg. blade having pitch of 13 mm.Exhaust Gril for return air-The exhaust air cabinets should be openable and cleanable. These cabinets should have suction from bottom.Distribution of exhaust air volume should be divided between fluff strainers to maintain the required pressure within the theatre without causing turbulence.The Exhaust air cabinet should be manufactured and supplied by the supplier of wall and ceiling system supplies. Also it should match perfectly with the ceiling system aesthetically.Make-conair/Bala ji engineering or Equivalent 141 ALUMINIUM DUCTING: 142 Aluminium Ducting ( 22 gauge ) with curves & bends where indicated for easy flow of air tight by applying silicon sealant after fabrication.Hangers will be provided to ducts & will be suspended be means of G.I. coated rod & these will not be more than 2.5 mtrs apart.Thermal insulation with 9/13mm XPE with aluminium foil for supply & return air ducts.Joints will be lapped with Nitrile tape for better insulation. (Laminar to AHU & Return air in all four corners) AHU to be placed near OT, not more than 6 meter.SITC OF Hand fabricated rectangular Aluminum Ducting in accordance with the approved ducting lay out drawing, complete with all accessories , dampers, guide, vanes, support, etc.Make-Hindalco/Virgo or Equivalent 143 AIR HANDLING UNIT 144 AHU System & Condensing Unit with consistingDOUBLE SKIN CASING: Outer Skin 0.6 mm Pre- Coated GI Inner Skin 0.6 mm Plain GI Frame Work Hollow Extruded AL Profile Thickness of Insulated Panels 25 mm thick, CFC Free PUF injected (Density: 40 kg / Cu. m.) Material ofDrain Pan 20 G SS-304 Tray duly insulated with 13 mm closed cell Nitrile insulation. Unit Base G.S.S Base Channel DX COIL: Make Of Coil ZECO Coil Casing / Blank offs GI Material Of Tube Copper (IGT) Tube Dia (mm / inch) 9.52 mm / 3/8” O.D. Thickness of tube (SWG / mm) 25 SWG / 0.5 mm Header Material Copper Thickness & Material of fins 0.15 mm Plain Aluminum No. of Fins per inch (FPI) 11 / 12 FILTERS: Media of Filters Synthetic (non woven type) Efficiency of Pre-filters (EU-4) 90 % down to 10 micron. Efficiency of Fine-filters (EU-5) 99 % down to 05 micron FAN & MOTOR: Fan make Nicotra Motor make CG Motor type TEFC Squirrel Cage IP 55 Protected VFD Compatible induction motor VFD: VFD make DELTA DOUBLE SKIN FLOOR MOUNTED HORIZONTAL AIR HANDLING UNIT SHALL HAVE:(WITH 25MM THICK PANEL) ◻ Mixing box with manually operated FA & RA damper in GI constructionDOUBLE SKIN CASING: Outer Skin 0.6 mm Pre- Coated GI Inner Skin 0.6 mm Plain GIFrame Work Hollow Extruded AL ProfileThickness of Insulated Panels 25 mm thick, CFC Free PUF injected (Density: 40 kg / Cu. m.) Material of Drain Pan 20 G SS-304 Tray duly insulated with 13 mm closed cell Nitrile insulation. Unit Base G.S.S Base ChannelDX COIL: Dx type coils having suitable number of distributors for connecting expansion valve with condensing unitsMake-Zeco//VTS or Equivalent 145 Make Of Coil Casing / Blank offs GI Material Of Tube Copper (IGT)Tube Dia (mm / inch) 9.52 mm / 3/8” O.D. Thickness of tube (SWG / mm) 25 SWG / 0.5 mm Header Material CopperThickness & Material of fins 0.15 mm Plain Aluminum No. of Fins per inch (FPI) 11 / 12FILTERS: Media of Filters Synthetic (non woven type)Efficiency of Pre-filters (EU-4) 90 % down to 10 micron. Efficiency of Fine-filters (EU-5) 99 % down to 05 micron VFD: DOUBLE SKIN FLOOR MOUNTED HORIZONTAL AIR HANDLING UNIT SHALL HAVE: (WITH 25MM THICK PANEL)Mixing box with manually operated FA & RA damper in GI constructions.Filter section with 50 mm thick (EU-4) box type pre filter with 305 mm thick (EU-5) bag type fine filter mounted on common filter frameCoil section with 6 row deep DX cooling coil with suitable distributor. Heater Section with GI strip Heater.Fan section with SISWbackward curved plug fan & Motor (IE-2). Manually operated SA damper in GI construction.Tonnage TR 8.5 Air Qty (CFM) 3500SP (mm wg) 125 UnitFan Type Plug Fan-355Fan model RLC E6-3135-23-19 Fan RPM 3400Motor RPM 2880Shaft Absorbing Power 3.2 Motor Rating (kw) 3.7 Motor pole 2Coil area (Sq.Ft.) 7.0 DX Cooling Coil RD 6 Distributor 1Heater KW3Filter area (Sq.Ft.) 8.0 Length (mm) 2500Width (mm) 1400 Height (mm) 945 146 AIRCONDITIONING: (8.5 T AC ) 147 Nominal Cooling Capacity-8.5tr,102000Btu/hr,29894watt Nominal Air Quantity-6250CFMPower Supply (V-ph-Hz)-400 ± 10% -3-5 Fan-PropellerDischarge-HorizontalFan Motor-Permanent Split Capacitor Type Power (watt)-470Control Type-LED DisplayOverall dimensions (mm)-982 X 610 X 1100 mm- Compressor- Scroll CompressorRefrigerant-R-410A (5.6) Liquid Line-5/8Suction Line-1-1/8Make- Carrier or Equivalent 148 ELECTRICAL WIRING INSIDE THE OT 149 Electrical Wiring as per requirement of OT, Wiring With OT distribution electrical Panel. ( Power cable at OT with Main distribution Panel will be provided by customer) Operation theatre shall be installed in the remote cabinet.All electrical wiring should be terminated to the connectors mounted on DIN/CE approved rail and labeled with indelible labels.Individual fuse and miniature circuit breakers should protect all internal circuits.Complete schematic diagram drawing description should be enclosed with the equipment. Makes:Scheinder/PolyCab/ Schematic.Supply, Installation, Testing and Commisnoing of Electrical Distribution Board with required MCB : It should be installed in a separate enclosure.Transformers,Mains,Relays,Circuitprotectiveequipment,forallcircuitsofOperationtheatreshallbeinstalledinthe remote cabinet. 150 MEDICAL GAS PIPE-LINE SYSTEM INSIDE OT 151 Medical Gas Pipe Line inside the OT above ceiling as required, complete with valve box and other required fitings. Medical Gas copper pipeline inside the OT and the Provision to connect to Pendant Systems (inside OT only).It should be confirm and meets with BS:EN:13348:2008 copper pipes.All medical grade degreased copper pipes must be inspected and duly Third Party Certified by Lloyd’s Registered Asia. Medical Grade Copper pipes manufactured from Phosphorous de-oxidized non-arsenical copper to BS:EN: 1412:1996 grade CW024A (Cu-DHP) manufactured to metric outside diameters and having mechanical properties in accordance with BS:EN: 13348:2008 & 250 or 290 (Half hard).Degreasing of pipe shall be such that there is less than 20 mg/m2(0.002mg/cm2) of hydrocarbons on the degreased surface when tested by the method specified BS:EN:13348:2008.Make- Altos/Aktiv/Mandev tubes/Mehta tubes or Equivalent 152 PASS BOX SIZE-2FTX2FTX2FT 153 Pass Box to remove the waste materials from the Operation Room to the Dirty Linen Area. Each box is equipped with two doors and the door should be operated electronically.. It is designed in such a way that only one door can be opened at one time. UV light is so installed that it is kept on while both the doors are closed and turned off automatically when the doors are opened. Indicators on both side of the Operation Room for Door Open/Close status. It is made of SS-304 Grade.Make- Jindal/Tata or Equivalent 154 STORAGE UNIT 155 Storage Unit of size 850x1600x350 mm has made of 1.6mm galvanised steel sheet. The exterior glass doors has lockable with magnetic push-button for easy opening. Removable toughened glass shelves of thickness 5 mm will be provided with the storage units.Make- Jindal/Tata or Equivalent 156 Pressure Relief Dampers 157 Pressure relief dampers should be provided in each room to prevent contamination of air from clean and dirty areas. Suitably sized air pressure relief damper should be strategically placed, enabling differential room pressure to be maintained and ensure that when doors are opened between clean and dirty areasCounter- weight balancing system should be provided in the PRD to maintain positive pressure inside the operation room.Air pressure stabilizers should have unique capability of controlling differential pressure to close tolerance.The PRD should remain closed at pressure below the set pressure and should open fully at a pressure only fractionally above the threshold pressure.The body of PRD sleeve and Grill should be epoxy powder coated as per standard High grade SS304 Stainless steel plate should be used for body and for bladesMake- Jindal/Tata or Equivalent 158 OT Pendant –Single Arm Anesthesia(Modular) 159 Anesthesia Pendent Systems should have the facility to provide convenient positioning of medical equipment.The support arms should be extremely robust and revolve on high quality bearings, so that the pendant head glides smoothly and quickly to any desired position.The Support arm should have atleast 10 mm thickness throughout to prevent any unnecessary deflection in Arms at given load.Arm Caps should be Aluminum Die casted Powder coated that allows its opening and closing a number of times as compared to ABS/Plastic end caps.High quality bearings shall be used to provide smooth and free movement, minimizing the force required to overcome static friction forces during repositioning. Bearings shall be permanently lubricated and sealed, withno maintenance or replacementPendant arms other than the cantilever lift arm shall be manufactured from extruded aluminium sections and available in various lengths. External surfaces of all arms shall be polyester powder coated in a RAL 9002/9003 finish. Tandem pendants for critical care areas shall be designed so that the consoles can readily swap sides within the bed bay to maximize the flexibility of the workspace.Non-return valves shall be fitted downstream of the connection to the medical / surgical air pipeline to prevent back-flow in the event of low distribution system pressure.Each arm should be capable of 330 – 340 degrees of rotation and be fitted with stops which can be easily adjusted to suit the desired mode of operation.Infinitely variable rotational stops should be available from 0-330 degree which shall enable precise of limits travel to be set to ensure maximum freedom of movement, whilst protecting walls and ancillary equipment.The rotational stops shall be dampened such that when limit of travel is reached, sensitive suspended equipment is not subjected to shock or vibration as the kinetic energy is absorbed.The arms may be fitted with pneumatic brakes or electromechanically breaks to prevent inadvertent movement.It should be possible to replace all medical gas hoses without the need for onsite crimping of ferrules. All medical gas hoses shall be colour coded to as per standard.The Pendant Service Heads / Column should be capable of accepting a range of shelves, drawers and infusion poles or other accessories. The Pendant Heads / column should support the range of Physiological Monitor Mounting Solutions. Service head should designed to host, Base, Gas Module, Electric Module and shelves.Make- Altos/Aktiv or Equivalent 160 The Pendant Service Heads / column should be supplied with medical gas terminal units. The medicalgas outlets fully comply with ISO 7396-1 and DIN 13260-2 standards. Medical gas hoses fully comply with thestandard BS EN 739 and are provided with NIST connectors to this standard. 161 Each anaesthesia pendant should be Single arm having rotational movement with load carrying capacity of minimum 120 kg having following facilities:movable Arm with total coverage of minimum 1000 mm and 330 degree.The Pendant Service Head/column should be modular with minimum 1200 mm head. Gas outlets: O2 – 2 nos, N2O – 2 no, Air (4 Bar) – 2 no, Vac – 2 nos, AGSS – 1 no. Medical rail with brake buttons fitted. - 1 No.Shelf with Drawer – 1 no. Infusion set – 1 no.Electrical Sockets – 10 nos. 6/16 Amp. 6 pin sockets. Pendants should comply with applicable standard:The terminal units must be according to ISO 7396-1 and DIN 13260-2 standards.Medical gas hoses shall be compliant to ISO 5359:2009 colour coded throughout its lengt 162 OT Pendant -SURGICAL PENDANT : 163 Surgon Pendent Systems should have the facility to provide convenient positioning of medical equipment.The support arms should be extremely robust and revolve on high quality bearings, so that the pendant head glides smoothly and quickly to any desired position.The Support arm should have atleast 10 mm thickness throughout to prevent any unnecessary deflection in Arms at given load.Arm Caps should be Aluminum Die casted Powder coated that allows its opening and closing a number of times as compared to ABS/Plastic end caps.High quality bearings shall be used to provide smooth and free movement, minimizing the force required to overcome static friction forces during repositioning. Bearings shall be permanently lubricated and sealed, withno maintenance or replacementPendant arms other than the cantilever lift arm shall be manufactured from extruded aluminium sections and available in various lengths. External surfaces of all arms shall be polyester powder coated in a RAL 9002/9003 finish. Tandem pendants for critical care areas shall be designed so that the consoles can readily swap sides within the bed bay to maximize the flexibility of the workspace.Non-return valves shall be fitted downstream of the connection to the medical / surgical air pipeline to prevent back-flow in the event of low distribution system pressure.Each arm should be capable of 330 – 340 degrees of rotation and be fitted with stops which can be easily adjusted to suit the desired mode of operation.Infinitely variable rotational stops should be available from 0-330 degree which shall enable precise of limits travel to be set to ensure maximum freedom of movement, whilst protecting walls and ancillary equipment.The rotational stops shall be dampened such that when limit of travel is reached, sensitive suspended equipment is not subjected to shock or vibration as the kinetic energy is absorbed.The arms may be fitted with pneumatic brakes or electromechanically breaks to prevent inadvertent movement.It should be possible to replace all medical gas hoses without the need for onsite crimping of ferrules. All medical gas hoses shall be colour coded to as per standard.The Pendant Service Heads / Column should be capable of accepting a range of shelves, drawers and infusion poles or other accessories. The Pendant Heads / column should support the range of Physiological Monitor Mounting Solutions. Service head should designed to host, Base, Gas Module, Electric Module and shelves.The Pendant Service Heads / column should be supplied with medical gas terminal units. The medical gas outlets fully comply with ISO 7396-1 and DIN 13260-2 standards. Medical gas hoses fully comply with thestandard BS EN 739 and are provided with NIST connectors to this standard.Each anaesthesia pendant should be Single arm having rotational movement with load carrying capacity of minimum 120 kg having following facilities:movable Arm with total coverage of minimum 1000 mm and 330 degree.The Pendant Service Head/column should be modular with minimum 1200 mm head. Gas outlets: O2 – 2 nos, N2O – 1 no, Air (4 Bar) – 1 no, Vac – 2 nos.Medical rail with brake buttons fitted. - 1 No.Make- Altos/Aktiv or Equivalent 164 Shelf with Drawer – 1 no. Infusion set – 1 no.Electrical Sockets – 10 nos. 6/16 Amp. 6 pin sockets. Pendants should comply with applicable standard:The terminal units must be according to ISO 7396-1 and DIN 13260-2 standards.Medical gas hoses shall be compliant to ISO 5359:2009 colour coded throughout its length. 165 UV LIGHT INSDIE OT FOR CLEAN/STERILIZE PERPOSE SIZE-2FTX1FT 166 Recess mounted sealed IP54 Protocol, non-hygroscopic UV peripheral lights ( 1 x 2 ) having compact high glow low wattage LED lighting system. These lights are having electrical safety code for high & low voltages.The luminaries for recess mounting in operation theatres should flush with the ceiling based on LED. Ultraviolet (UV) lamps are commonly used in operation theatres for disinfection.Luminaries cover made of highly-resistant, disinfectant-proof acrylic diffuser with white coated frame.Closing devices are integrated automatically in the electrical safety control without lines having to be connected to the luminaries housing. Luminaries’ body made of sheet steel, white, powder-coated, supplied ready for connection optionally for individual or group with power saving technology. Luminaries with protection IP 65, and protection class I,230 V,50 Hz.Recess frames for the gas-tight installation of clean-room luminaries in IP 65 in suspended ceilings.Frame made of extruded aluminium profile, white, powder-coated, able to be put together to form a rigid, continuous frame by means of plug and screw connections.Make- Altos/Dgline or Equivalent 167 Surgical Scrub Station – Two Bay 168 Compact surgical scrub sink should be designed for use in OT complex providing for pre – OT scrub up. Each fixture should be fabricated from heavy gauge type 304 stainless steel and should be seamless welded construction, polished to a satin finish.The washing faucet shall be made of Chrome plated brass hand. The station shall be equipped with soap dispensers made of SS 304 grade.The scrub sink should be provided with a front access panel which should be easily removed for access to the water controlled value, waste connections, stoppers and strainers.Hands free operation should include infra red sensors with built-in range of adjustment.The scrub station shall be made of high-grade stainless steel 304 with stain polish finish and wired to the current IEE regulations & BS 7971.Thermostatic mixing, valve control should be located behind the access panel and maintain constant water temperature. User defined setting of 1,3,6 & 10 min should be available. This timing should be adjustable to meet individual application requirements.All units should have reduced anti- splash fronts.The scrub stations control system shall be based on advanced microprocessorThe scrub station shall be sensor-activated 24VAC and should have the provision to operate it manually in case of power failure by using foot switch or knee switchimported thermostatic mixing valve for Hot & Cold water, Strainers, Spouts & manual foot operated valve system.Make- Jindal/Tata or Equivalent 169 AUTOMATIC PHASE SEQUENCE CONTROLLER 170 PMC Based (Pre magnetic Contractor)63A Double interlock & time Delay systemAuto/Manual Operation Sie- 140 x 275 x 320 mm Smooth and fasr Switchingworks well even at high & low voltages. Wide Current rnge.Voltage Range-130-280Vac Temperature- 55 Degree Celsius Auto mode Selector switchDigital micro Control relay for sequence management.LED Indicator for complete status of power.Make- Subtech or Equivalent 171 Operation Theatre Light - LED type, Camera Ready (Triple Arm) 172 Operating Room Surgical Lighting system should provde an ideal combination of broghtness, maneuverability, and shadow resolution without sacrificing color accuracy throuh a consistent LED technology. Such Lighting System should have the following technical specifications: 173 a. Number of light heads : Two per suspensionb. Colour Temperature range : 3800k-5000 (±10%) - Variable color temperature. c. Field Size Diameter : 20 to 28 cm (+/- 10%)d. Working range : 750 to 11100 mm (+/- 10 %)e. Illumination Level : 160000Lux (major Dome & Minor dome )f. Rotation : 360 - 330 degree g. Sterilizable Handle : 02 Nos h. Mounting type : Ceiling i. Supply Voltage : 230 VAC 50 Hz j. Bulb Type : LEDk. Dimming Range : 50% - 100%l. Operating / Storage Humidity : 10 - 95 %m. Life of Light source : > 40,000 Hrs n. Should be provision to mount the camera in 1 dome . o. Surgical Light System Should be compliant with relevant European CE / US FDA standardsMake- HillRom/Steris orEquivalent 174 GST Extra as applicable