The Subject Of The Order Is A Backhoe Loader With Accessories. Technical Images: 1. Backhoe Loader Factory New, Year Of Production 2025, Backhoe Loader That Meets The Requirements Of The Vehicle Approved To Travel On Public Roads In Accordance With Applicable Provisions Of The Road Traffic Act2. Drive System: A. Diesel Engine - Power Min. 74.4 Kw, (100 Km) Meeting The Euro Stage V Standards, Torque Of At Least 420 Nmb. Automatic Gearbox - A Minimum Of 6 Gears Forward, And A Minimum Of 3 Backwards, Powershift Type With Momentuc Substitute Lock. Four -Wheel Drive 4X4 With The Possibility Of Choosing One Or Two Housing Drive. Front Swivel/Fluent Axle, Front Torsion Wheels, Rear Torsion Wheels, Crab Turning Mode. Front Wheels Min. 28 Inches, Back Wheels Min. 28 Inches3. Hydraulics: A. Multi -Piston Pump With A Variable Expenditure. Maximum Performance Min. 160 L/Minc. Maximum Pressure Min. 255 Bard. On The Excavator Boom, A Double Hydraulic Installation Is Mounted For Power Supply, E.G. A Wood -Gripped Wood Gripper. Hydraulic Quick Coupling. Rear Stabilizers Independent, Hydraulically Extended With The Indicator Of The Marginal Position Of The Stabilizers4. Charger Arm: A. 4 In 1 Multifunction Spoon, Equipped With A Hydraulic Connector, Opened With Screwed Teeth. Palette Forks Mounted On A Quick Coupling. Charger Spoon Capacity Min. 1.1 M3, Spoon Width Min. 2,400 Mmd. Charger Spoon Equipped With A Spoon Depreciation And Spoon Leveling (Arm Stabilization) E. The Loading Height Of The Charger Spoon Is Not Less Than 3.25 Mf. Load Capacity In A Charger Spoon At A Maximum Height Of A Minimum Of 3.3 Tg. Pulling Force On A Charger Spoon Min. 7300 Kgfh. Controlling The Loading System With A Single Joystick With The Function: Possibilities Of Changing The Direction Of Driving, The Function Of Opening And Closing The Spoon, Leveling And Leveling. It Must Have A Return Spoon Return System To The Charging Position5. Backhoe Arm: A. Telescopic Excavator System, Hydraulically Shifted On The Back Frame. Control Of An Excavator System With Two Joysticks Located With A Rotating Cushioned Operators Armchair. Hydraulic Excavator Quick Coupling - Original Machine Manufacturer. Digging Depth Min. 5.6Me. The Range Of The Output Of The Arm Measured From The Inside Of The Rear Wheel At Least 8100 Mmf. Digging Range At The Ground Level Measured From The Boom Rotation Pin Min. 6680 Mmg. Working Height Min 6500 Mmh. Minimal Power To Separate The Bucket Of The Excavator 7000 Kgfi. The Minimum Force Of Tearing Off The Telescopic Arm Of 2200 Kgfj. Digging Spoon - Width Min. 300 Mm With Teeth (+- 10%) K. Digging Spoon - Width Min. 600 Mm (+- 10%) L. Sock Spoon, Hydraulic, Torsion - Width Min. 1500 Mm (+- 10%) 6. General Requirements For The Machine And Cabin Equipment: A. Total Length Max 6100Mmb. Height With A Max 3000Mmc Cabin. Diaper Spacing Min 2100 Mmd. Machine Operating Mass In The Range Of 9500 - 10,000 Kge. Fuel Tank Min. 140 Lf. Blottors Of The Front And Rear Wheels. Reve
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
