Sacrificial Fabric. Raw Materials: Polyester. Weight: 85 G/M2. Density: 160 Microns. General Width: 1800 Mm. Temperature Resistance: 180 ° C. Application: On Epoxy And Polyester Composite Systems, Conducting Mesh. Raw Materials: Hdpe. Thickness: 1 Mm. Width: 2000 Mm. Density: 160 G M2. Temperature Resistance: Up To 140 ° C. Color: Green. Compatibility: Pe, Vinyl Ester, Epoxy Resins. Application: For Vacuum Infusion, The Dividing Film. Thickness: 30 Microns. Width: 150 Cm. Density: 0.97 G/Cm3. Temperature Resistance: 150 ° C. Extension Of The Gap: 500-800%. Perforation: Perforation P31 (About 6 Holes Per Cm2). Application: For Vacuum Infusion, Clutch For Vacuum Tubes. The Clamping Of A Screw For Mixing Tubes With A Diameter Of Up To 20 Mm. Aluminum Clamp With Photoplanes Protective Inserts. It Consists Of A Base, In The Lower Part Of Which A Locking Fluoroplastic Insert Is Installed, In The Upper Part A Screw With A Thread For The Possibility Of Pissing The Tube, A Spiral Tube For The Distribution Of Resin In Vacuum Infusion. Inner Diameter: 8Mm. External Diameter: 10Mm. Temperature Resistance - Up To 90 ° C. Suitable For Polyester, Epoxy Resin, Fiberglass. Fiber: Ec 9. Superficial Density: 280 G/M2. Weaving: Sarzha. Width: 1000 Mm. Application: Parts In Aircraft Manufacturing, Automobile Parts, Shipbuilding. Good Drapery. Very Good Impregnation, Very Transparent, Vacuum Tube. Ldpe/Pvd Plastic Tube Is Not Collapsed From Vacuum. Inner Diameter: 10Mm. External Diameter: 12Mm. Thermal Resistance: Up To 60 ° C. Used To Create Vacuum Lines, Supply Of Resin, Vacuum Film. Raw Materials: Nylon. Density: 50 Microns. Polurukov Width: 1000 Mm. General Width: 2000 Mm. Temperature Resistance: 180 ° C. Color: Blue. Application: For Vacuum Infusion, Connector For Infusion. Diameter: For A Tube 10 Mm. Raw Materials: Silicone. Temperature Resistance: Not Lower Than 130 ° C. Compatibility: Suitable For The Supply Tube 10/12Mm. Used To Create Vacuum Lines, Supply Of Resin, Vacuum Tube. Ldpe/Pvd Plastic Tube Is Not Collapsed From Vacuum. Inner Diameter: 8Mm. External Diameter: 10Mm. Thermal Resistance: Up To 60 ° C. It Is Used To Create Vacuum Lines, The Supply Of Resin., Sealing Tourniquet. Thickness: 3 Mm. Width: 13 Mm. Rolon Length: 15 M. Temperature Resistance: 150 ° C. Color: Black. Application: For Vacuum Infusion, Matrix Gelcout With Hardener. Two -Component Thixotropic Filled Epoxy Composition Based On Modified Epoxy Resin And Polyamine Type Hardener. The Composition Of The Gelcoat Includes Silicaorganic And Mineral Additives. It Does Not Contain Volatile Solvents. The Appearance Of The Resin Part: Dense Mass Of Dark Red Color. The Appearance Of The Hardener: Colorless Or Slightly Yellowish Liquid Of Medium Viscosity. The Ratio Of The Resin Part/Hardener: 100: 9 Weight. H. The Appearance Of The Compound: The High -Skinned Mass Of Dark Red Color. Hele Formation Time In A Layer Of 1-2 Mm., T = 25 ° C: 60 Min. Life Time In Mass 200 G, At T = 25 ° C: 40 Min. Complete Curing At T = 25 ° C: At Least 24 Hours. The Total Weight Of A Gel Core With A Hardener Can: 1.09 Kg, Spray Glue Of Temporary Fixation With High Adhesion, Wide Coating, Transparent And Quickly Grasping. Suitable For Fixing: Fiberglass, Carbon Monoxide. Tara: Block 600 Ml, Epoxy Resin With Hardener. Smol Color: Transparent With A Small Yellowish Tint. The Viscosity Of The Resin At 25 ° C: 1400-1800 Mpa · S. Resin Density: 1.1-1.2 G/Cm3. Epoxy Equivalent: 0.53-0.59 Eq/100G. Helpers Color: Transparent With A Small Yellowish Tint. The Viscosity Of The Hardener At 25 ° C: 10-15 Mpa · S. Amine Content: 500-600 Mg Koh/G. Epoxy Equivalent: 0.53-0.59 Eq/100G. Compound Life Life: 90 Minutes. The Total Weight Of A Can Of Resin With A Hardener Jar: 1 Kg, Connector T. Diameter: 10 Mm. Temperature Resistance: 90 ° C. Used To Create Vacuum Lines, Supply Of Resin, Carbon Fabric T240. Fiber: 3K. Design (Base): 6 ± 0.3 Threads/Cm. Design (Ducks): 6 ± 0.3 Threads/Cm. Density: 245 G/M2. Width: 1200 Mm. Weaving: Sarzha. Thickness: 0.24 ± 5% Mm, Divisive Wax. Wax For Creating A Dividing Layer, For Multiple Selection Of Parts From The Matrix, With Obtaining A Smooth, Glossy Surface. The Use In The Production Of Products Based On Epoxy, Polyester, Styrene, Acrylic And Other Types Of Resins: Bank 500 Grams, Connector L. Diameter: 10 Mm. Temperature Resistance: 90 ° C. Used To Create Vacuum Lines, Supply Of Resin
