Bids Are Invited For Future And Eventual Hiring Of A Specialized Company To Supply And Install Public Luminaires With Led Technology, Including All Materials, Equipment, Specialized Labor And Other Necessary Inputs, Aiming At The Modernization And Improvement Of Public Lighting In Various Urban And Rural Locations Of The Municipality Of Atílio Vivacqua/Es, Established By The Administration

240 Watt Led Limits Set Installation Service, Each Lamp Set Consists Of The Materials Described Below: • 1 240 Watts Led Public Lamp, Including Nema Base 7-Pin Materials, Total Ip-66 Degree, Minimum Luminous Flow, Minimum Energy Effectiveness Of The 120Lm/W, Maximum Power. Kg (+/- 5%). Dimensions: Min 640Mm Max 675Mm / Width Min 310Mm Max 340Mm / Height Min 90Mm Max 110Mm. Led Light For Public Lighting, Should Have A Total Ip-66 Degree Of Protection, Bronze Filter Sintended To Balance The Pressures, White-Colored Electrostatic Painting 9016, Tcc From 4000K To 5500K, Irc = 70, Power Factor = 0, 95. Thd = 10%, Subrtoadial Protector For The Drive And Led, Should Support Peak Tension Impulses Of 10,000 ± 10% V (Normalized Waveform 1, 2/50? S) And 10,000A Discharge Current (Standard Waveform 8/20? S), In Differential Mode (L1-Terra, L1-L2/N, L2/N-Terra), Should Withstand 15 Outbreaks Of Up To 10 Ka, Connected In Series Providing Greater Safety To The Luminaire, Opening The Circuit In The Burning Of The Spd, Avoiding Larger Damage And Leaving The Luminaire Erased At Night For Easy Identification Of It By The Maintenance Team. The Driver Should Enable Dimatization By Signal 0-10V, By Telegeminate System. The Rim Should Be Fixed By 3 Aluminum Locks Or Stainless Steel Screws. Body Safety Lock System After Opening Up, Maintaining Proper Ergonomics For The Assembler. Flower Body And Rim In Injected Virgo Aluminum Alloy High Pressure, With High Mechanical Resistance. Led With Primary Lens In Pmma And Secondary Lens In Tempered Flat Glass In Order To Ensure The Quality Of The Equipment, Avoiding Yellowing By Sun Wear And Other Weather. The Thermal System Of The Luminaire Should Occur Through The Body With Dissipating Fins, Ensuring The Installation Service Of 150 Watts Led Luminaires, Each Set Of Lamp Is Composed Of The Materials Described Below: • 1 Public Led Lamp 150 Watts, Based On Minimum Luminous Flow Of 16,700Lm, Minimum Energy Effectiveness 115Lm/W, Power Maximum 150W - Max Weight: 9.00 Kg. Dimensions: Min 510Mm Max Length: 525Mm / Width Min 280Mm Max 295Mm / Height Min 90Mm Max 115Mm. Led Luminaire For Public Lighting, Bronze Filter Synthesized To Balance The Pressures, Additional Outbreak Protector For The Drive And Led, Through A Telegenest System. The Rim Should Be Fixed By 1 Closure Of Aluminum Or Stainless Steel Screws. Body Safety Lock System After Opening Up, Maintaining Proper Ergonomics For The Assembler. High -Pressure Aluminum Aluminum Sipping Body And Rim, Ensuring The Thermal Operating Stabilization N, 1000 Watt Led Reflector Installation Service, Ip66, With Light Flow To 96.000Lm, Nominal Current Up To 100 - 250 V, With An Opening Angle Of 120º, Frequency 50/60 Fz, With A Life Of 25,000 Hours, Measuring 700 Mm X 340 Mm X X 35 Mm., 300 Watts Led Reflector Installation Service, With 19,500Lm Luminous Flow, Nominal Current Up To 100 - 240 V, Measuring 285 Mm X 205 Mm X 28 Mm. 05/06/2025, Installation Service