Tenders Are Invited For Annual Maintenance Of The Centers Passenger/Hospital And Hospital Elevators

Engine Room Maintenance, To Carry Out Inspection And Maintenance Of The Control Station, To Carry Out Maintenance Of The Access Device, Fixing The Wires In The Controller, Electrical Contact At The Connection Point Of The Power Wires To The Motor, The Controller And The Electromagnetic Brake, Brake Maintenance: Before Checking The Brake, Place The Counterweight On The Buffer. Inspect The Brake And Make Sure There Is No Mechanical Damage To Its Components And Replace The Brake Pads If Necessary. Clean The Brake From Impurities. It Is Necessary To Wash And Clean The Brake Pulley. Check And Tighten The Fastening Of The Parts. Check Clearances, Adjust If Necessary According To Clauses 3.6.6 And 3.6.5 Of Ti Of The Winch. To Check The Accuracy Of Cabin Stops On The Floors, The Required Accuracy Is Achieved By Cleaning The Brake And Repositioning The Magnets On The Shaft, Respectively, In Paragraph 3.6.1 Of The Ti Of The Winch., Maintenance Of Reducer And Winch Frame: Cleaning Of Reducer And Winch Frame. Check The Reducer And Frame. Inspect Welds And Threaded Joints. Check The Oil Level In The Reducer. Check For Oil Leakage In The Places Where The Cover And Shafts Are Installed - Change The Oil In The Reducer - Check The Breakdown Of The Screw Pair Of The Reducer By Measuring The Side Gap According To The Ti Of Bugurgad, Sheave Pulley (Kash) And Pulley Block Maintenance: Stop The Cab At The Top Stop. Clean Tile And Block From Impurities, Check And Tighten Fasteners. Check The Support Of The Tile And Block, Change If Necessary (Paragraph 4.3 Of The Ti Of The Winch), Speed ​​Limiter (Sm) Maintenance: Remove The Seal From The Sm. To Remove Impurities From Sm. To Check The Condition Of Components And Elements Of Sm With An External View. Tighten The Fastening Of Sealed Components And Elements. Check Contact Of Sm. Press The Link Of The Contact Of Sm And Leave The Cabin. Checking The Consistency Of Sms Support With An External Review, Maintenance Of The Circuit Breakers Of The Correction Race: Check And Clean The Device That Ensures The Operation Of The Circuit Breakers When The Cab Passes The Last Operating State. Checking The Movement Of The Elbow To The Ling Of The Extinguishers. To Check The Operation Of The Last Circuit Breakers, Raise (Lower) The Cabin 50 Mm Above (Lower) The Level Of The Upper (Lower) Stop By Turning The Control Wheel And Release The Elevator For The Sample, Maintenance Of Tension Ropes And Ropes Of Sm: Clean Tension Ropes And Grooves Of Sm From Impurities. Check The Condition Of The Calves Along Their Entire Length. To Carry Out The Test With Separate Parts Of 2 M Length With The Input Device Turned Off., Maintenance Of Magnets And Indicators Of Directional Devices, Electrical Apparatus And Electrical Disconnectors: Cleaning Magnets, Tightening The Supports. Checking The Interaction Of Cabin Indicators With Magnets Installed On The Portal, Adjusting If Necessary. Carrying Out Maintenance Of Call Posts And Light Indicators. Check The Condition Of The Circuit Breakers. Checked And Lubricated Main And Counter Load Guides, Maintenance Of Frosted Doors, Cleaning Of Equipment (Scrapers, Rollers, Counter-Rollers, Rasps, Switches, Etc.) Replacement Of Freezer Doors With New Slippers If Necessary. To Carry Out An External Inspection Of The Doors And To Check The State Of Fastening Of Their Components, Check The Adjusted Clearances, Adjust The Doors If Necessary According To Ti: Adjust The Clearances Between The Rollers Of The Locks And The Sides Of The Elbows Of The Cabin Doors When The Wheels Are Covered. Adjusting The Depth Of Access To The Groove Of The Locking Wheels. Repeatedly Checking The Operation Of The Control And Raza Block When Each Lock Is Operated, Counterweight Maintenance: Inspect Counterweight Components. Check The Condition Of The Counterweight And Suspension Fastening. Check Final Side And Final Face Clearances Between Liner And Guides. Checking The Gap Between The Buffer Of The Reverse Gap And The Buffer Of The Suspension In The Hole