Bids Are Invited For This Involves The Acquisition Of Electrical Material To Assist The Urban Action Secretariat In Replacing The Maintenance Of The Citys Public Lighting Network, Through A Bidding Procedure, Electronic Auction, Financed With Its Own Resources, Source 190 And With Resources From Source 117 , As Specified In This Terms Of Reference

Arm For 3 Meter Led Luminaire The Support Arms For The Luminaires Must Comply With The Following Requirements Finish - Free From Burrs Sharp Corners Flattening Of Sections Or Other Defects Incompatible With Their Use Surface Protection - Must Be Painted In Red 48Mm Diameter Tube Thickness 3.0Mm. Mechanical Resistance The Arm Correctly Installed On The Post Must Meet The Arrow Values ​​When Applied To Vertical Forces And Horizontal Forces. Torque Resistance The Base Must Withstand The Installation Torque Of 7.6 Da N Permanent Or Sinking, Led Luminaire – Nominal Power Between (38W And 42 W), For Lighting Public Roads, With Nominal Supply Voltage Of 220Vac, 50/60 Hz, Minimum Luminous Flux Between (6080 And 6720 Lumens). The Optical System Must Be Made Through Lenses/Reflectors, Positioning The Light Where It Is Needed And Minimizing Glare To Users (Type Ii Photometric Classification), The Optical Assembly Must House The Leds And Lenses/Reflectors In A Cavity Free Of Dirt And Dust With An Optical Protection Ip66 (Minimum). All Luminaires Must Have A Minimum Efficiency Of 160 Lm/W And A Color Temperature Of 5,000K, High Color Reproduction Index (Irc), From 70 (Inclusive). Minimum Service Life Of 100,000 Hours With (Maintenance Of 70% Of Initial Flow), Power Factor Of 0.92 Or Greater. Total Harmonic Distortion Of Input Current In Accordance With Abnt Nbr 16026. Must Be Constructed With Chassis And Support Block In High Pressure Injected Aluminum With Support For Fixing On 48 Mm Tubular Post Arm, Using Corrosion Resistant Paint, Complying With Rohs Standard(Not Contain Lead Or Mercury). Minimum 5-Year Warranty Against Manufacturing Defects With Mandatory Presentation Of The “Warranty Term”. The Leds Must Be Of The High Power Or Mid Power Type, Leds Of The Low Power Or Cob Type Will Not Be Permitted. The Registration Must Be Presented With The Inmetro., Hot-Dip Galvanized Square Head Machine Screw M16x200mm, With Galvanized Nut And Washer., Extruded Aluminum Parallel Connector, Hot-Dip Galvanized Steel Accessories, 1 3/8” Screw, Main 10-70Mm2 – Derivation 10-70Mm², Individually Packed In A Colorless Transparent Polyethylene Bag Closed By Electronic Welding And Supplied With Anti-Oxide Compound., Cdp-70 Perforation Connector, High Insulation Self-Fusion Tape For Splices And Terminations Of Low Voltage Cables, Operating Temperature Of 0 At 90°C, Minimum Elongation Of 600% Without Breaking, Made Of Ethylene Propylene Rubber, Minimum Thickness Of 0.75Mm, Width 19Mm, Length 5M., Pvc Insulating Tape Covered With Rubber-Based Adhesive Layer, Class A, Resistant To Uv Rays, Black, Minimum Thickness (0.19Mm), Width (19Mm), Length (20M), Minimum Elongation Of 200%, Minimum Disruptive Voltage 9500V, Self-Extinguishing, Minimum Temperature Class 100°C. Must Meet Abnt Nbr Nm 60454-3-1 And European Rohs Standard, Photoelectric Relay, Mechanical Drive – Thermal, 220Vac, 60 Hz, Polypropylene Material With Protection Against Uv Rays, Nf, Illuminance Less Than 20 Lux To Turn On And Less Than 80 Lux To Turn Off, Surge Protection System, Minimum Ip 54, Minimum 1 Year Warranty, Minimum Resistive Control Power Of 1000W. The Plug-In Contacts Must Be Made Of Brass, Electrolytically Tinned And Rigidly Fixed To The B