Quotation Are Invited For Hp-Lp Reduction Station Nozzle Replacement And Drain Line Spool Pipe With Elbow Replacement During L2 Station Total Shutdown

Quotation are invited for HP-LP Reduction Station Nozzle Replacement and Drain Line Spool Pipe with Elbow Replacement during l2 Station Total Shutdown FOR L 2-MBR. TECHNICAL AND GENERAL SPECIFICATIONS - OUTSOURCING WORK. L STATION PHASE2, JEBEL ALINAME OF WORK:#SCOPE OF WORK FOR1.#HP-LP REDUCTIO N STATION NOZZLE REPLACEMENT,PERIOD OF WORK:#06 CALENDAR DAYS DURING PLANT TOTAL SHUTDOWN (TENTATIVESTART DATE 02.01.2025)SCOPE OF W ORK·#THE CONTRACTOR SHALL VISIT THE SITE AND MAKE HIMSELF FULLY FAMILIARWITH THE WORK SCOPE, PLANT ACCESS, FACILITIES, COMPLEXITIES, SAFETYMEASURES, ERECTION PROCEDURES, NUMBER OF WELDS ETC., BEFORE HE SUBMITSHIS BID.·#PARTY SHALL SUBMIT ITP ALONG WITH WPS AND ERE CTION PLAN AFTER GETTINGPO AND BEFORE COMMENCING ANY WORK.·#AWARDING THE PO DOES NOT GUARANTEE THAT COMPLETE QUANTITY IN THE POWILL BE CARRIED OUT. ACTUAL QUANTITY OF REPLACEMENT WILL BE DECIDEDBASED ON INSPECTION AND PAYMENT SHALL BE BASED ON ACTUAL WORK CARRIEDO UT·#TO GET A PTW, HWP CONTRACTOR MUST SUBMIT RISK ASSESSMENT FORMS ANDMETHOD STATEMENT PRIOR TO START THE WORK.·#CHECK CONDITION SUI TABLE TO CARRY OUT WORK. CONDUCT SITE SURVEY ANDSAFETY INSPECTION TO ASSESS THE WORKING ENVIRONMENT.·#A SAFETY MEETING WILL BE HELD TO EVALUATE THE RISK INVOLVED INMETHODS TO BE USED. RISK ASSESSMENT AND TOOLBOX TALK TO BE CONDUCTED TOALL CONTRACTOR TEAM.·#THE PAR TY SHALL MOBILIZE THE LABOR, EQUIPMENT, TOOLS, ETC.IMMEDIATELY AFTER DEWA NOTIFICATION. THE PARTY SHALL BE READY TO STARTTHE WORK WI TH ONE-DAY ADVANCE NOTIFICATION.·#ALL LIFTING AND POWER TOOLS SHALL BE TESTED AND A TEST CERTIFICATE TOBE PROVIDED TO DEWA.·#THE PAR TY SHALL VERIFY THAT SCAFFOLDS ARE SAFE TO WORK AND VALIDSCAFFOLDING TAGS ARE PROVIDED BEFORE USING ANY SCAFFOLDING.·#REMOVE ALL THE REQUIRED CLADDING SHEETS, INSULATION AND INSULATIONFIXING CLAMPS. DISPOSE OF THE DAMAGED INSULATION ON THE DESIGNATED AREASHOWN BY DEWA ENGINEER FOLLOWING DEWA RULES AND REGULATIONS. KEEP THECLADDING SHEET AND GOOD INSULATION IN PROPER WAY.·#INSPECT, MEASURE, AND COMPARE THE MEASUREMENTS, PROFILES, SIZE, CLASSAND ORIENTATIONS BETWEEN THE SUPPLIED NOZZLE AND EXISTING NOZZLE. INCASE OF ANY DEVI ATIONS IDENTIFIED, IMMEDIATELY INFORM TO DEWA.·#AFTER PROPER CHECKING AND CONFIRMATION OF SUPPLIED NOZZLE / ELBOW,PREPARE ADDITIONAL SUPPORTS AND LIFTING ARRANGEMENTS TO HOLD THEPIPELINES IN POSITION AND CUT EXISTING SUPPORTS IF REQUIRED.·#MARK AND CUT THE INLET A ND OUTLET JOINTS AS PER THE NEW NOZZLE ANDELBOW WITH PIPE DIMENSIONS. REMOVED THE OLD NOZZLE AND ELBOW WITH PIPESHALL SAFELY BRING D OWN TO GROUND LEVEL AND SHALL KEEP IN A SAFE MANNER.·#INSPECT THE EXITING INLET AND OUTLET PIPING FOR ANY DEFORMATIONS /DEFECTS.·#CO NTRACTOR SHALL TAKE INTO CONSIDERATION THAT THE EXISTING PIPESURFACES MAY HAVE IRREGULARITIES IN SHAPE AND THICKNESS, WHICH PARTYSHA LL RECTIFY BEFORE FIT UP.·#SURFACE PREPARATION OF INLET AND OUTLET JOINTS AS PER APPROVED WPS /ITP.·#SURFACE PREPARATION OF NEW NOZZ LE AND ELBOW WITH PIPE INLET ANDOUTLET JOINTS AS PER APPROVED WPS / ITP.·#ERECTION OF NEW NOZZLE AND ELBOW WITH PIPE IN THE SAME ORI ENTATION OFREMOVED ONE AND FIT UP OF INLET AND OUTLET JOINTS.·#FINAL ALIGNMENT OF EACH FIT UP JOINTS SHALL VERIFY BY CONTRACTOR QCIN PRESENCE OF DEWA. WELDING SHALL START AFTER DEWA CLEARANCE ONLY.·#WELDING OF NOZZLE , INLET AND OUTLET PIPING AS PER APPROVED WPS / ITP.·#EXTRA PRECAUTION SHALL BE TAKEN DURING EXECUTION OF JOB NOT TO DAMAGEANY NEARBY EQUIPMENT.·#AFTER COMPLETION OF ABOVE SCOPE OF WORK, JOINT INSPECTION WITH DEWAENGINEER.·#ON SUCCESSFUL COMPLETION OF NDT, HEAT TREATMENT PROCEDURES AND AFTERFINAL CLEARANCE FROM DEWA, INSTALL BACK INSULATION CLAMPS, INSULATION,AND CLADDING SHEETS.·#IN CASE OF NON-COMPLETION OF THE PROJECT WITHIN THE STIPULAT ED TIMEOR EXTENSION OF SHUTDOWN DUE TO ANY REASONS FROM THE CONTRACTOR#S SIDE(INCLUDING FAILURE OF NDT), DEWA RESERVE THE RIGHT TO B ACK CHARGE THECONTRACTOR. Qty: 2 HP-LP Reduction Station Nozzle Replacement and Drain Line Spool Pipe with Elbow Replacement during l2 Station Total Shutdown FOR L 2-MBR NOTE: The contractor shall visit the site and make himself fully familiar with the work scope, plant access, facilities, complexities, safety measures, Erection procedures, number of welds etc., before he submits his bid. STANDARD TERMS & CONDITIONS 1) Prices should be DDP delivery duty paid at DEWA stores. 2) Quotation to be submitted only in local currency U.A.E Dirhams 3) DEWA Standard payment terms is 30 days credit from the date of acceptance of material 4) No DEWA staff or his or her relatives up to third degree should have ownership or partnership in your company, and your participation in DEWA tenders / RFQs should not constitute a Conflict or perceived Conflict of Interest. Supplier Registration: https://srm.dewa.gov.ae/irj/portal/anonymous/regis Tender Link : https://srm.dewa.gov.ae/sap/opu/odata/sap/ZSRM_RFX_REG_BID_SRV/AttachmentSet(2332402741)/$value