Bids Are Invited For Hiring A Specialized Company For Maintenance And Renovation Of The 200M³ Metallic Reservoir.

Removal Of Supported Metallic Reservoir Ceiling.Removal Of Supported Metallic Reservoir Ceiling.Diã‚Meter = 5.75M; Removal Of The Roof/Total Beams And The Internal Mast (6€ Diameter And 9 M Height), Blasting/Treatment And Reinstallation Of The Supported Metallic Reservoir Roofblasting/Treatment And Reinstallation Of The Supported Metallic Reservoir Ceiling (Existing). : 5, 75M., Execution And Installation Of Tubular Guardrails On A Supported Metallic Reservoir. Execution And Installation Of Tubular Guardrails On A Supported Metallic Reservoir; With Reuse Of The Existing Guard Body.Tube: Din 11/4€, 3Mm Thickness, 1.20 Meters Height (According To Safety Standard Nr-12), With A Minimum Spacing Of 20 Cm Between Protection Bars; A Protection Bar Around The Entire Perimeter With 3 Cm To 5 Cm High From The Ceiling, To Prevent Falling Tools And/Or Other Objects; The Guardrail Must Be Fixed/Welded To The Cover/Side, Do Not Use Screws. Lid Diameter 5.75M, Locking Beams For Supported Metallic Tanklocking Beams For Supported Metallic Tank; €Œu†Format 4, 75Mm ; Throughout The Reservoir Area, With A Rotating Brush. Reservoir Dia‚Meter = 5.75M And Height = 9M; Including The Lid., Internal Mechanical Blasting Of The Supported Metallic Reservoirinternal Mechanical Blasting Of The Supported Metallic Reservoir; Over The Entire Area Of ​​The Reservoir, 100% With Sa3 Standard Grit, Diameter Of The Reservoir = 5, Internal Epoxy Polyamide Coating On A Supported Metal Reservoirinternal Epoxy Polyamide Coating On A Supported Metal Reservoir, On The Entire Area Of ​​The Reservoir, As Per Specification: Background Painting High-Thickness Two-Component Polyamide Epoxy, In One Coat Of 150 (One Hundred And Fifty) Microns, In Gray Or Red; Internal Finishing Painting In High Thickness Two-Component Epoxy Enamel, In Two Coats Of 150 (One Hundred And Fifty) Microns Each Coat, In A Total Of 450 (Four Hundred And Fifty) Microns., External Coating On The Supported Metallic Tankexternal Coating On The Supported Metallic Tank, In The Entire Area Of ​​The Reservoir With Application Of High Thickness Paint, In One Coat Of 125 (One Hundred And Twenty Five) Microns In Gray Or Red; External Finishing Paint In High-Thickness Two-Component Epoxy Enamel, In Two Coats Of 125 (One Hundred And Twenty-Five) Microns Each Coat, In A Total Of 375 (Three Hundred And Seventy-Five) Microns. The Lower Part, From The Base To 1.50M In Height, Is Finished In Pu (Ulha Tar), The Same Thickness., Installation Of Hydraulic Plumbs In A Supported Metal Reservoir. Installation Of Hydraulic Plumbs In A Supported Metal Reservoir. Opening And Installation Of Plumbs Hydraulics: Supply And Installation Of Two Inlet Pipes (Internally), With Flange, Diameter Of 6€In Carbon Steel Tube, Painting Of The Tube, Internal And External With Epoxy Primer Paint, Non-Toxic, Secured By Steel Clamps, Two Steel Bends, 90º, In The Upper Part Of The Inlet Pipe., Threadable Hole In The Base Of The Supported Metallic Tankthreadable Hole In The Base Of The Supported Metallic Tank, 1€ Diameter For Installing A Pressure Gauge, Including The Supply Of The Pressure Gauge, Dia‚Meter 4€, For Minimum Gauge Height 0 - 50 Mca,