Bids Are Invited For Price Registration For Hiring A Company Specialized In Adaptation Of Vehicles For Vehicles, As Requested By The Municipal Secretariat For Safety And Mobility

Graphics Application Service On Vehicles Visual Identification (Graphics) Will Be Applied According To The Corporations Standard, Through Stickers In The Locations Defined As Per The Layout Presented, To Be Applied On The Vehicle, Which Must Have The Predominant Color Gcm Standard. Identification Stickers Will Be Affixed To The Graphics, In Accordance With The Corporations Standard, Noting That The Letters, Numbers And Telephone Symbol Will Be Made From Reflective Vinyl And The Logos From Non-Reflective Vinyl. The Visual Identification (Graphics) Of Police Vehicles Must Be Applied By The Contracted Company In Accordance With The Standard Adopted By The Institution. Identifying Stickers Will Be Affixed To The Painting, In Accordance With The Gcm Bertioga Standard. 2.1. Technical Specification Of The Adhesive Film: 2.1.1. Premium High Performance Cast Cast Or Calendered Pvc Film (Oracal, 3M, Avery), With Polymeric, 0.5 Mm To 0.7 Mm, Specific For Use In Electronically Controlled Flat Cutters. 2.1.2. Protective Silicone Paper: Double-Sided Pe Coated Paper, One Side Siliconized, With At Least 43 G/M²; 2.1.3. Adhesive: Solvent Polyacrylate, Repositionable, Permanent, Transparent Glue, Must Meet The Area Of ​​Use, Intended For Long-Term Outdoor Applications, And Large Format Digital Prints, With The Highest Degree Of Gloss And Durability. 2.2. General Technical Data To Be Observed: 2.2.1. Thickness (Without Paper And Adhesive): 60 Micron; 2.2.2. Dimensional Stability (Finat Tm 14); 2.2.3. Adhered To Steel Shrinkage, No Shrinkage In Transverse Direction, Length 0.2Mm Max; 2.2.4. Temperature Resistance: Adhered To Aluminum, -50 C To + 90 C (Short Term, Maximum 24H To + 100 C), No Variation; 2.2.5. Seawater Resistance (Din 50021); 2.2.6. Adhered To Aluminum, After 100H /23 C, No Variation; 2.2.7. Resistance To Solvents And Chemicals (Test Certificate) - At Room Temperature, 72 H Adhered To High-Resistant Aluminum, Visual Signal Width Between 250 Mm And 500 Mm And Height Between 50 Mm And 70 Mm, Installed By The Winning Bidder On The Roof Of The Vehicle; Built With A Base And Lid In Translucent Polycarbonate (With Uv Treatment, Resistant To Impact And Discoloration), Reinforced With An Extruded Aluminum Profile And Closing The Lid Using Stainless Steel Screws. The Lighting System Must Consist Of At Least 18 Reflectors, Including 07 Front Reflectors And 07 Rear Reflectors, Each Equipped With 06 (Six) Leds, In Addition To 04 Side Reflectors, 02 On The Left Side And 02 On The Right Side Of The Signal. , With 06 (Six) Leds Per Reflector. All Led Modules Must Be Bicolor, Allowing Them To Light Up In Red Or Blue, According To The Animation Pattern. Nominally Powered With 10.8 To 14.7 Vdc; If Red Leds Are Used Juxtaposed To Blue Leds, The Leds Must Not Be Spaced In Such A Way That The Filling Of The Module Is Harmed. Each Led Must Have A Minimum Power Of 03 Watts And Comply With The Specifications Described Below: ?Predominant Color Red And Blue; ?Wavelength 610 To 630 Nm; ?Luminous Intensity Of Each Led Is At Least 90 Typical Lumens; ?Allngap Category; Animation Patterns: ?A) Round: 450 Millisecond Pulse, 50 Millisecond Interval. Sequence: All Modules