Tenders Are Invited For V 00784A - Pcb Production Line

The Subject Of The Performance Of This Contract Is The Delivery Of The Performance Expected Within The Planned Subsidy Project Establishment Of A Center For The Development Of Printed Circuit Boards Registration Number Cz.01.01.01/03/23_024/0002598, Specifically In This Case It Is The Supply Of A Pcb Production Line. The Technical Parameters Are As Follows, With The Fact That The Client Allows Their Modification While Maintaining The Principle That The Performance And Range Parameters Are Set As Minimum And The Size And Weight Parameters As Maximum, Unless Something Else Is Stated For A Specific Parameter, With A Tolerance So That The Device Can Be Installed And Connected To The Clients Existing Equipment In The Place Designated For This Equipment. The Supplier Is Responsible For The Fact That The Order Will Be Delivered Complete And Will Contain All Parts Necessary For Flawless Operation. Only Original (Not Refurbished) Components Will Be Used For Production. The Technical Specification Sets The Basis For The Minimum Requirements For Function, Performance, Service Life, Etc. By Confirming The Order, The Relevant Supplier Undertakes To Comply With All Points Of This Document. If The Zd Or Its Annexes Contain Specific Trade Names Or Brands, This Is Only A Definition Of The Required Standard, And The Contracting Authority Also Allows Other Technically And Qualitatively Comparable Solutions. Technical Specification Of The Line For The Production Of 1-Sided Pcbs Consisting Of The Following Components: 1. Cutting Device, Suitable For Pcb Up To 3 Mm Thick, Aluminum Up To 2 Mm Thick, Steel Up To 1 Mm Thick, Films, Plastics, Etc. Cutting Length Max. 530 Mm. 1 Piece 2. Freestanding Brushing Device, Maximum Pcb Width 400 Mm. Simultaneous Brushing Of Both Sides Of The Board. Adjustable Conveyor Speed 0.2 - 2 M/Min, Max. Thickness Pcb 0.3 - 5 Mm. Wet Process, Final Mechanical And Hot Air Drying. Closed Rinsing System With Integrated Tank For Rinsing Water, Filter And Pump Unit. Power Supply 230 V, 50 Hz. 2 Pcs 3. Dry Resist Roller, Can Also Be Used For The Application Of Special Laminates, Such As Solder Masks. Lamination Speed 0.5 - 1.5 M/Min. Maximum Lamination Width 400 Mm. Fully Digital Temperature Setting And Display For Laminating Rolls. 1 Piece 4. Dry Rolling Resist, 1.5 Mil, Width 400 Mm, Roll 152 M. 2 Pcs 5. Led Exposure Unit. One-Sided, For Panels Up To 450 X 1200 Mm Format. Digital Timer For Setting The Exposure Time (9 Min 59 Sec). Simple Vacuum Sealing Using Mylar Foil. 1 Piece 6. Production Spray Conveyor System For Pcb Development. Working Width 500 Mm, Conveyor Speed 0 - 1.5 M/Min, Pump Capacity 200 L/Min, Tank Volume 55 L. External Max. Dimensions 1200 X 670 X 1290 Mm, Power Supply 220 V, 50 Hz, 1 Piece 7. Production Spray Conveyor System For Pcb Etching. Working Width 500 Mm, Conveyor Speed 0 - 1.5 M/Min, Pump Capacity 200 L/Min, Tank Volume 55 L. External Max. Dimensions 1200 X 670 X 1290 Mm, Power Supply 220 V, 50 Hz. 1 Piece 8. Production Spray Conveyor System For Pcb Stripping With Filter Basket System. Working Width 500 Mm, Conveyor Speed 0 - 1.5 M/Min, Pump Capacity 200 L/Min, Tank Volume 55 L. External Max. Dimensions 1200 X 670 X 1290 Mm, Power Supply 220 V, 50 Hz. 1 Piece 9. Conveyor Rinse Unit, Freestanding, Adjustable Conveyor Speed, Integrated Magnetic Valve For Fresh Water Inlet, Transport Height And Width Same As Dps Production Line, 230V. 1 Piece 10. Bowls Under The Dps Line Equipment And Under The Rinsing Unit, Preventing Spillage 4 Pieces 11. Conveyor Dryer For Dps Line, Power Supply 230 V, 50 Hz, Approx. 3.5 Kw. 2 Pcs 12. Driven Entry Tables, Pvc/Titanium Construction With Pur Conveyor Belts, Effective Cylinder Width 510 Mm, Total Format Approx. 1200 Mm X 700 Mm. Drive Via Motor With Gearbox, With Potentiometer Adjustable Speed Control, Compatible With Dps Production Line 1 Piece 13. Non-Powered Output Tables, Compatible With The Dps Production Line. 4 Pieces 14. Water Treatment Plant For Cleaning And Recirculation Of Rinse Water From Etching Equipment Only. 1 Piece 15. Tank 500 L For Automatic Replenishment Of Ferric Chloride In The Etching Equipment, Reinforced, With Cover + Toothed Shut-Off Valve, Without Pump (Overflow Change Of Etchant Based On The Integrated Pump Of The Dps Line). 1 Piece 16. Negative Developer For 10 L. 50 Pcs 17. Anti-Foaming Agent For Developing And Stripping Units, 1 Liter Bottle. 2 Pcs 18. Striper For Positive + Negative Resist, 1 Bag = 250 G. 20 Pcs 19. Liquid Ferric Chloride, 40%, 25 Liter Canister. 10 Pcs Part Of The Subject Of Performance And The Price Is Also The Cooperation Of The Supplier During Installation And Recovery At The Installation Site At The Clients Place And Operator Training. The Order Is Not Divided Into Parts. The Contracting Authority Does Not Intend To Discuss Offers With The Participants In The Sense Of Article 5.4 Of The Rules.