Bids Are Invited For Acquisition Of Furniture (Cabinet, Chairs, Shelves, Board, Sofas, Etc) Intended For Use In School Units Of The Municipal Education Network Of The Education Department.

Steel Cabinet 2 Doors With Locksteel Cabinet 2 Doors 4 Shelves – Am4 (Proinfância)Description: Tall Steel Cabinet, Divided Vertically Into Two Compartments By Means Of Partitions With Independent Doors, Equipped With Four Removable And Adjustable Shelves In Each Compartment. Dimensions And Tolerances : Width: 900 Mm +/- 10 Mm; Depth: 400 Mm +/-10 Mm; · Height: 1980 Mm +/- 10 Mm; · Tolerances For Paint Layer: Minimum 40 Micrometers / Maximum 100 Micrometers. Characteristics: Body, Partitions And Doors In Cold Rolled Steel Sheet - Plate 22 (0.75 Mm); Shelves And Door Reinforcement In Cold Rolled Steel Sheet - Sheet 20 (0.90 Mm); Base In Cold Rolled Steel Sheet - Plate 18 (1.25Mm); Door Locking Bars Ø = 1/4” (Minimum); Internal Hinges Not Visible On The Exterior Of The Furniture Made Of Cold-Rolled Steel Sheet - Sheet 14 (1.9 Mm) With A Minimum Of 75 Mm In Height - Three Units Per Door; Fully Metal Canopy Door Handles, With Cremona System Locking; Cylindrical Drum Lock Built Into The Handle With A Minimum Of 4 Pins; Keys In Duplicate, Attached To The Corresponding Door Handles; Printed Or Overlaid Label Holder, The Latter Being Exclusively Made Of Non-Ferrous Chrome Metal Alloy; Epoxy/Polyester Hybrid Powder Paint Painting, Glossy Electrostatic, Polymerized In Oven, Minimum Thickness Of 40 Micrometers In Gray Color., Steel File Cabinet With 04 Drawerssteel File File – Aq1 (Proinfância)Description: Sliding Steel File Cabinet With Four Mounted Drawers On Telescopic Rails That Allow Total Opening. Dimensions And Tolerances: Height: 1330 Mm +/- 10 Mm; Width: 470 Mm +/- 10 Mm; Depth: 710 Mm +/- 10 Mm; Tolerances For Paint Layer: Minimum 40 Micrometers / Maximum 100 Micrometers. Characteristics: Body And Internal Structure In Steel Sheet 22 (Thickness 0.75 Mm) In Gray Color; 24 Sheet Metal Drawers (0.60 Mm); Telescopic Rails And Galvanized Guides In Plate 18 (1, 20 Mm) Or Higher; Sheet Drawer Locking Rod 16 (1.50 Mm); Lower Closure (Next To The Floor) In Plate 24 (0.60Mm). Zamac Handles In 96 Mm Steel Finish. Cylindrical Drum Lock (Minimum 4 Pins) With Simultaneous Drawer Locking System. Duplicate Keys. Compressors For Folders In All Drawers. Printed Or Overlapping Label Holder, The Latter Being Exclusively Made Of Non-Ferrous Metal, Chromed Or Nickel-Plated. Drawers Equipped With Telescopic Rails Composed Of Linear Guides With Steel Ball Bearings, With A Minimum Vertical Load Capacity Of 45 Kg And Anti-Escape Mechanism, Chromed Metal Leveling Shoes With An Injected Polypropylene Base. Painting In Hybrid Epoxy / Polyester Powder Paint, Electrostatic, Glossy, High Chairfeeding Chair – C1 (Proinfância)Description: Foldable Infant High Chair, With Removable Tray.Dimensions And Tolerances: Height: 1050 Mm +/- 50 Mm; Width: 560 Mm +/- 50 Mm; Depth: 680 Mm +/- 50 Mm; Side Protection: Minimum 140 Mm, Measured From The Top Of The Side Protection To The Surface Of The Seat; · Backrest Height: Minimum 250 Mm, Measured In Vertical Position; · Backrest Angle: Minimum 60º In Relation To The Horizontal (If Smaller, The Minimum Backrest Length Must Be 400 Mm); Seat Front Edge: Minimum Radius 5 Mm. Features: Supports Up To 15 Kg; · Folding Chair, With Carbon-Steel Circular Section Tubular Structure; Seat And Back Padded With Wool-Coated Foam