Tenders Are Invited For Improving The Cultural Offer By Expanding The Village Community Center In Dzierzgówek

Scope Of Investment: Footings - Reinforced Concrete Foundations, Monolithic, Concrete Class B25, Main Reinforcement 4#12 Class Aiiin, Stirrups Every 20Cm Ø6 Class Ai. The Footings Are Placed On A Layer Of B10 Class Lean Concrete, 10 Cm Thick. The Width Of The Benches Is 80 Cm, The Height Is 40 Cm. Foundation Walls - Foundation Walls Are Thick. 24[Cm] Concrete Block Placed On Z2.2.3. External Walls - Burnt Red Brick Walls - 42 [Cm] Thick, Built On Cement And Lime Mortar, Systemically Insulated With 20 [Cm] Thick Styrofoam. Internal Walls - Load-Bearing Internal Walls, Thickness. 24.0 [Cm] - Made Of 24 [Cm] Thick Blocks On A System Mortar - Partition Walls 12.0 [Cm] Thick - Made Of - Made Of Aerated Concrete Blocks - Brick The Partition Walls On A Thin-Layer Mortar; Ceilings - The Stop Is The Lower A Wooden Truss Strip Made Of A 3.5X16cm Board, Which Is A Supporting Structure For A Ceiling Frame Made Of Plasterboards Or Armstrong Ei30 Type. Wreaths - Reinforced Concrete Wreaths, Wet-Cast. Reinforcement With 4#12 Rods, Ø6 Stirrups At 20Cm Spacing. Stairs - Not Applicablelintels - Reinforced Concrete Lintels, Wet-Cast Or Prefabricated. Ventilation Ducts - Ventilation Ducts - System Ventilation Blocks Ended With Ventilation Grilles In The Wall At The Inlet To The Duct And On The Chimney At The Outlet From The Sewer. - Ventilation Of The Sanitary Sewage System In The Form Of A Dn160 System Chimney, Extended Above The Roof Surface To A Height Of 0.5-1.0 [M]; Cement Mortar And 15 [Cm] Of Xps Polystyrene Thermal Insulation; Passages And Culverts - Should Be Made In The Walls , Ceilings And Foundations, Installation Culverts/Passages In Accordance With Industry Designs And Connection Designs And The Requirements Of Fire Protection Regulations; - Pvc Pipe Culverts Should Be Installed In The Holes; - The Diameter Of The Culverts Should Be Matched To The Pipe Diameter; Insulation Of Footings And Foundation Walls - Horizontal: To Be Performed By Laying 2 X Roofing Felt On Adhesive. - Vertical: Made Of Dispersion Mass (Does Not Contain Solvents) After Priming The Substrate With A Product Of The Same System. Insulation Should Be Made Of At Least Consumption 1.5 [Kg/M2/Mm] Moisture-Proof Insulation Of Floors. After Making The Base Concrete, Lay The Pe Foil Folded Over The Wall, 10.0 Cm Hard Polystyrene And The Pe Foil Again. After Installing The Insulation And Flooring, Excess Foil On The Wall Should Be Removed. Thermal Insulation - Foundation Walls - Extruded Polystyrene 15 [Cm] Thick, E.G. Xps Polystyrene; - External Walls - Styrofoam 20 [Cm] Thick - Suspended Ceiling - Mineral Wool 15+5[Cm];Wind Insulationwaterproof, Windproof Roof Foil Reinforced With A Highly Vapor Permeable Mesh, Roofing Felt On The Formwork.Vapor Barriervapour-Barrier Foilfloors And Floorsindoor Floors Made Of Anti-Slip Tiles, Plinths;Plasters And Wall Claddinginternal: Use Category Iii Cement And Lime Plasters With Gypsum Plaster Or Machine Plaster, The Surface Of Which Must Be Made In The Quality Of Gypsum Plaster; External: Mineral, Acrylic, Silicone-Silicate Plaster Or Lamb Silicate, Grain Size 1.5 [Mm], Painted With Silicone Paint Or Colored In The Mass (Light Wet Technology Of The Building Insulation System) ;Ceilingsceilings On The Ceiling: Gypsum Board, Gypsum Plaster, Paint Coating Or Armstrong Ceiling 60X60 In Fire Class Ei30.Windows And Doors.External Windows.Typical Pvc External Windows. Use Reinforced, Insulated, Tilting Aluminum Profiles, Opening Accessible From The Floor, Double Glazing, Glass With U = 0.9 [W/M2k] Coefficient. External Doors. External Steel Joinery Was Designed. The Doors Open In Accordance With The Drawings Of The Study. Door Handles In The Color Of Stainless Steel.Interior Doorsinterior Doors Were Designed From Wood-Like Chipboard, Veneered, Color Consistent With The Arrangement And Arrangements With The Investor At The Construction Stage. Adjustable Door Frame Adapted To The Wall Thickness. Fittings In The Color Of Stainless Steel. Roof Covering. The Roof Is Covered With Metal Tiles In A Color Agreed With The Investor. Cross-Sections Of The Wooden Elements Of The Truss According To Architectural And Construction Drawings. Wall Battens Placed On The Ceiling Should Be Anchored In The Reinforced Concrete Ring With Anchors Ø12 [Mm] Every 1.5 [M]. The Roof Truss Should Be Impregnated Against Fungi And Fire, E.G. With Fobosm2 According To The Manufacturers Instructions. Sheet Metal Flashings - Downpipes - Pvc; - Sheet Metal Flashings - In The Color Specified By The Investor. Roof Drainage. Rainwater From The Buildings Roof Will Be Drained Using Gutters And Downpipes Attached To The Façade. And Hidden In The Insulation Layer And Discharged To The Plot Surface. Square Roof Gutters With A Polyvinyl Chloride Cover, Diameter: 110 [Mm] Connected With A Gasket, Round Downpipes Made Of Polyvinyl Chloride, Diameter. 90 [Mm] E.G. Marley Stormflo Or Equivalent. Additional Works - Make A Concrete Band Around The Building On A Sand Bed With A Slope Of 1.0 [%] From The Building - Parking Spaces And Access To The Building Should Be Made Of Paving Stones 8 Cm Thick, On Ballast Sand-Cement Thickness: 3 Cm And Lean Concrete Thickness: 10 Cm - Panel Fence Height: 1.53 M X 2.5 M, Concrete Foundations And The Gate And Goal Are Made Of Closed Steel Profiles Filled With Elements From System Fencing Panels. Color To Be Agreed With The Investor.