Tenders Are Invited For Construction Of A Building In Zero-Emission Technology Using Renewable Energy Sources For A Day Care Seniors Home In Wydrzyn

4.1. The Subject Of The Order Are Construction Works Under The Task Titled: Construction Of A Building In Zero-Emission Technology Using Renewable Energy Sources Intended For A Day Care Home For Seniors In Wydrzyn.4.2. As Part Of The Investment, A Building Will Be Constructed In Zero-Emission Technology With Land Development. A Heat Pump With Power From Photovoltaic Panels Will Be Installed To Heat The Building. A Building Intended For Residents, Rehabilitation Rooms With Sanitary Facilities And Kitchen Facilities.4.3. The Scope Of Works To Be Performed Includes In Particular: 1) Reinforced Concrete Foundation Strips With A Width Of 80.0 Cm And A Height Of 50.0 Cm Made Of C20/252 Concrete) Reinforced Concrete Cores Of Foundation Walls With Dimensions Of 25.0 X 25.0 Cm Made Of C20/25 Concrete) Dimensions 35.0X25.0Cm Made Of C20/254 Concrete) Roof Structure - Designed With Roof Trusses - According To The Design Of Wooden Trusses5) Partition Walls Thick. 12 Cm And 9 Cm Made Of Ceramic Hollow Bricks6) Accordion-Shaped Mobile Wall With An Aluminum Structure Filled With Wood-Based Boards7) Smoke Chimney Ø20 With Two System Ventilation Ducts8) Thermal Insulation Works 9) Moisture-Proof Insulation Works10) Roofing Treatments Made Of Coated Steel Sheets Thick. Min 0.5Mm11) Drainage Through External Gutters12) Suspended Ceilings13) External Aluminum Window Joinery With Umin Coefficient = 0.9, Graphite Color. 14) External Aluminum Door Joinery With Umin Coefficient = 1.3, Graphite Color. 15) Typical Internal Door Joinery Made Of Wood-Based Materials And Aluminum 16) Internal Plasters And Internal Wall Cladding 17) External Window Sills Made Of Sheet Steel, Thick Sheet Metal Min. 0.7 Mm. 18) Internal Sills Made Of Conglomerate19) Insulation Of External Walls With Eps70 Polystyrene, 20 Cm Thick20) Execution Of The Following Installations: A) Electrical Installation B) Water Supply Installation C) Sewage Installation D) Central Heating Installation E) Air-Conditioning Installation F) Mechanical Ventilation21) Implementation Of Land Development22) Delivery And Installation Of One Information Board With Dimensions Of 180X120 Cm On A Frame Or Posts Made Of Stainless/Powder-Galvanized Steel - A Board Informing About The Co-Financing Of The Task.23) Obtaining, On Behalf Of The Ordering Party, A Non-Final Occupancy Permit Or A Certificate Of No Grounds For Objection To The Notification Of The Construction Supervision Authority About The Completion Construction.24) Characteristic Parameters Of The Facility: Usable Area - 706.8 M2 Building Area - 808.7 M2 Cubic Capacity - 2358.2 M3 Building Height - 6.98 M Building Length - 47.85 M Building Width - 24.35 M Number Of Storeys – 1 Attention! The Scope Of This Order Does Not Include The Supply Of Equipment. The Detailed Scope And Method Of Performing Construction Works Are Specified In: 1) Design Documentation, Which Consists Of: A) Construction Design, Exit Reconstruction Design, Construction Technical Design, Electrical Technical Design, Sanitary Technical Design; 2) Detailed Technical Specifications For The Execution And Acceptance Of Construction Works (Stwiorb): Construction Industry, Electrical Industry, Sanitary Industry;3) Bills Of Quantities (Attached As An Aid);4.5. Equivalent Solutions. In Each Case Of Using Standards, Technical Assessments, Technical Specifications And Technical Reference Systems Referred To In Art. 101 Section 1 Point 2 And Section 3 Of The Public Procurement Law, The Contractor Should Assume That Such A Reference Is Accompanied By The Words Or Equivalent. If References To Standards, European Technical Assessments, Approvals, Technical Specifications And Technical Reference Systems Are Used In The Design Documentation, The Ordering Party Allows Solutions Equivalent To Those Described. When Analyzing The Design Documentation, The Contractor Should Assume That Each Reference Used In The Design Documentation Is Accompanied By The Word Or Equivalent. If Trademarks Are Used In The Design Documentation Or Technical Specification For The Execution And Acceptance Of Works, It Means That They Are Provided As Examples And Only Define Minimum Expected Quality Parameters And The Required Standard. The Contractor May Use Equivalent Materials Or Devices, But With Similar Or Better Technical And Quality Parameters, The Use Of Which Will In No Way Adversely Affect The Proper Functioning Of The Solutions Adopted In The Design Documentation. The Contractor Who Will Use Devices Or Materials Equivalent Will Be Obliged To Demonstrate During The Execution Of The Order That The Equipment And Materials Used By Him Meet The Requirements Specified By The Ordering Party. The Use Of A Label In The Design Documentation Means That The Ordering Party Accepts All Labels Confirming That Given Construction Works, Supplies Or Services Meet The Equivalent Requirements Specified By The Ordering Party. Labels. If The Contractor, For Reasons Beyond Its Control, Cannot Obtain The Label Specified By The Contracting Authority Or An Equivalent Label, The Contracting Authority, Within The Deadline Set By Itself, Accepts Other Appropriate Means Of Evidence, In Particular The Manufacturers Technical Documentation, Provided That The Contractor Proves That The Construction Works , Deliveries Or Services To Be Performed By Him Meet The Requirements Of A Specific Label Or Specific Requirements Indicated By The Ordering Party. The Use In The Design Documentation Of The Requirement To Have A Certificate Issued By A Conformity Assessment Body Or A Report On Tests Carried Out By This Body As Evidence Confirming Compliance With The Requirements Or Features Specified In The Description Of The Subject Of The Contract, Offer Evaluation Criteria Or Contract Performance Conditions Means That The Contracting Authority Also Accepts Certificates Issued By Other Equivalent Conformity Assessment Bodies. The Ordering Party Also Accepts Other Appropriate Means Of Evidence, In Particular The Manufacturers Technical Documentation, In The Event That A Given Contractor Has Neither Access To Certificates Or Test Reports Nor The Possibility Of Obtaining Them In An Appropriate Time, Unless This Lack Of Access Cannot Be Attributed To A Given Contractor. , And Provided That The Contractor Proves That The Construction Works, Supplies Or Services Performed By Him Meet The Requirements Or Criteria Specified In The Description Of The Subject Of The Contract, The Offer Evaluation Criteria Or The Requirements Related To The Implementation Of The Contract. If The Description Of The Subject Of The Order Includes A Provision Resulting From Knr Or Knnr Indicating The Need To Use Specific Equipment With Specific Parameters In The Execution Of The Order, The Ordering Party Allows The Use Of Other Equipment Provided That It Will Ensure The Achievement Of The Assumed Design Parameters And Will Not Cause The Risk Of Non-Compliance Of The Work Performed With The Technical Documentation.