Tenders Are Invited For Partial Renovations Of The Surface Of Municipal Roads In The Kruszwica Commune

Common Procurement Vocabulary: Cpv 45230000-8 Construction Works For The Construction Of Pipelines, Communication And Power Lines, Highways, Roads, Airports And Railways; Land Leveling Cpv 45233142-6 Road Repair Works Ordering Party: Kruszwica Commune Completion Date: Up To 8 Weeks From The Date Of Conclusion Of The Contract1. Subject Of The Order: The Subject Of The Order Is The Performance Of Partial Renovations Of Municipal Roads Located In The Kruszwica Commune With Bituminous Surfaces And Made Using The Surface Consolidation Method With Asphalt Emulsion And Grit. The Order For The Renovation Of Municipal Roads Made Using The Method Of Surface Consolidation With Asphalt Emulsion And Grit Includes: • Filling Of Gaps Up To 2 Cm Deep With Asphalt Emulsion And Grit Using A Renovator • Filling Of Gaps Up To 4 Cm Deep With Asphalt Emulsion And Grit Using A Renovator • Liquidation Of Cracks And Rakowin With Asphalt Emulsion And Grit Using A Renovator. The Scope Of Work Related To Filling In Defects, Potholes, Broken Edges And Eliminating Cracks And Rakowin With Asphalt Grits And Emulsion Using A Renovator Includes:• Preparing The Damaged Place For Repairs• Covering The Cleaned Place By Spraying With Asphalt Emulsion Whose Task Will Be To Bind The Substrate And The Edges Of The Repaired Pavement Defect With The Filling• Filling The Defect Under Pressure With 5/8 Mm Or 2/5 Mm Grit (Depending On The Depth Of The Defect) Surrounded By Asphalt Emulsion• Filling The Remaining Part Of The Defect Under Pressure With 2/5 Mm Fraction Grit (If Used For The Bottom Layer Of 5/8 Mm Grit) Covered With Asphalt Emulsion• Sprinkling The Surface Of The Renovated Area With Dry 2/5 Mm Grit Without Binder• Cleaning Up The Area After The Renovation• Removing Safety Devices And Vertical Markings And Opening The Area Of ​​The Renovated Section To Traffic. The Ordering Party Does Not Allows For Renovations Using A Sprinkler And Manual Scattering Of Grit. The Order For The Renovation Of Municipal Roads With A Bituminous Surface With A Hot Mineral-Bituminous Mixture Includes: • Embedding Mmb In The Amount Of 150 Mg Hot. The Scope Of Works Related To Filling The Defect, Pothole, Broken Edges With A Mineral-Bituminous Mixture. Hot Bitumen Includes:• Preparation Of The Damaged Area For Repairs• Cutting Out Damaged Areas Of The Surface And Giving Them Regular Shapes• Cleaning Of Damaged Areas With Removal And Disposal Of Excavated Material• Supplementing The Base With Mechanically Stabilized Crushed Aggregate 0/31.5 Mm Up To The Height Of The Lower Bituminous Surface • Sprinkling The Repaired Places With C60b3zm Asphalt Emulsion In The Amount Of 0.5 Kg/M2. • Spreading The Mineral And Bitumen Mixture With A Grain Size Of 0/8 Mm (Ac8 S 50/70) And 0/11 Mm (Ac11 S 50/70) For Kr 2, Laid Manually Or Mechanically Using Pavers And Steel Rollers Or Compactors In One Or More Two Layers Depending On The Depth Of Damage• Compaction Of Individual Layers Of The Applied Mixture• Cleaning Up The Area After The Renovation• Removal Of Safety Devices And Vertical Markings And Opening The Area Of ​​The Renovated Section To Traffic Order For The Renovation Of Municipal Roads With A Bituminous Surface With A Hot Mineral-Bituminous Mixture - Overlay In Wróble (According To The Bill Of Quantities) Includes: • Cold Milling Of Bituminous Surfaces On A Thickness Of Up To 4 Cm• Cleaning And Sprinkling Of Structural Layers - Bituminous Layers• Carrying Out Partial Renovations Of Bituminous Asphalt Surfaces With Mineral-Asphalt Mixtures, With Cutting Off The Edges Of Damage Manually On The Main Course• Making A Wearing Course Of Asphalt Concrete Ac 11 S Thickness. 4 Cm• Cleaning Up The Place After The Renovation• Removing The Safety Devices And Vertical Markings And Making The Area Of ​​The Renovated Section Accessible To Traffica) The Renovation Sites, Together With An Indication Of The Route (Marking The Repair Points With Paint), Will Be Made By The Employers Representative And The Contractors Representative In A Protocol Within 5 Business Days From Signing The Contract. B) The Acceptance Of The Works Must Be Carried Out In A Protocol By The Representative Of The Ordering Party And The Contractor. C) Renovations Will Be Carried Out On Municipal Roads In The Kruszwica Commune And In The City Of Kruszwica. D) The Order Includes The Performance Of All The Activities Listed Below, Which Will Result In The Renovation Of Roads In Quantities:• Partial Renovation With Asphalt Emulsion And Grit Using A Renovator, Without Cutting The Edges, With An Average Depth Of Defects Of 2 Cm: 1000 M²• Partial Renovation With Asphalt Emulsion And Grit Using A Renovator, Without Cutting The Edges, With An Average Depth Of Defects Of 4 Cm: 1000 M² • Partial Renovation With Asphalt Emulsion And Grit Using A Renovator, Without Cutting The Edges - Rakowinia: 450 M² • Partial Renovation Of Bituminous Surfaces With Mineral-Bituminous Mixtures, With Cutting The Damaged Edges Manually: 150Mge) The Contractor Is Obliged To Have Appropriate Technical Equipment. The Equipment Listed Below Must Be In Full Working Order, Ready To Be Presented To The Tender Committee: • Saw For Cutting Asphalt - 1 Piece • Pneumatic Hammer - 1 Piece • Compressor (Blower) For Removing Impurities And Dust - 1 Piece • Heater For Drying And Pavement Heating - 1 Pc.• Plate Compactor Or Roller - 1 Pc.• Emulsion Sprayer - 1 Pc.• Car With A Thermos With Double Walls And Heating System - 2 Pcs. • 5T Tipper Car - 1 Pc.• Specialist Road Repairer - 1 Pc.• Bituminous Mass Paver Equipped With An Electronic Controller And A Vibrating Board Or Equivalent Equipment – ​​1 Pc.• Mechanical Brush – 1 Pc.• Self-Propelled Binder Sprayer Equipped With A Measuring Device And An Adjustment Mechanism That Ensures Even Distribution Of Binder In The Longitudinal And Transverse Directions –1 Pc.• Surface Milling Machine – 1 Pc.• Static Roller – 1 Pc.F) The Ordering Party Requires The Submission Of An Offer Cost Estimate To The Contract.2. Requirements Of The Ordering Party In Connection With Art. 95. Of The Public Procurement Law: The Ordering Party Requires The Contractor Or Subcontractor To Employ, Under An Employment Contract, Persons Performing All Activities Included In The So-Called Direct Costs Under An Employment Contract. This Requirement Applies To Persons Who Perform Activities Directly Related To Construction Works In The Implementation Of The Subject Of The Order In The Number Of People Necessary To Perform The Subject Of The Order, Including: Construction Worker - Road Works, If The Performance Of These Activities Involves Performing Work Within The Meaning Of The Provisions Of The Labor Code, Unless These Activities Are Performed By A Person As Part Of A Business Activity. Detailed Requirements In Connection With Art. 95 Of The Public Procurement Law Were Included In §19 Of The Contract Template.