Tenders Are Invited For Reconstruction Of The Municipal Public Road No. 103992R, Kolejowa Street In Kolbuszowa, Including The Construction Of Parking Spaces, Necessary Infrastructure And Construction Equipment

1. The Subject Of The Order Is The Implementation Of Construction Works Entitled: Reconstruction Of The Municipal Road No. 103992R, Kolejowa Street In Kolbuszowa, Including The Construction Of Parking Spaces, Necessary Infrastructure And Construction Equipment2. The Detailed Scope Of Works Is Specified In The Construction Design, Executive Designs And, Additionally, In The Bill Of Quantities. 3. The Scope Of The Investment Includes: 1) Execution Of Leveling Works And Earthworks - Trenches For The Structural Layers Of The Designed Infrastructure. 2) Execution Of Structural Layers Of The Substructure And Road Surface Within The Intersection Shield. 3) Execution Of Structural Layers Of The Substructure And Sidewalk Surfaces - On The Approaches To The Designed Cross The Road.4) Construction Of Construction Layers And Foundation For 7 Parking Spaces.5) Hardening Of The Area On Plot 1539/12 - Between Ul. Ruczki And The Existing Garages. 6) Construction Of Drainage Of The Paved Square As Above - Connection To The Existing Kd300 Rainwater Collector Of The Parking Lot, Draining Rainwater And Meltwater To The Existing Collector In Ul. Fr. Ruczki.7) The Planned Expansion Of The Existing Lighting Includes: Expansion Of The Existing Street Lighting With Additional Lighting Fixtures Marked As Op1, Op2 - Pedestrian Crossing Lighting And L1, L2, L2.1. – Lighting Of The Existing Street With Sidewalk And Parking Lot. The Planned Lighting Should Be Connected To The Existing Pole No. 19/2012 With A Designed Yakxs 4 X 35Mm2 Cable, And Then Distributed Successively To The Designed Lighting Poles In Accordance With The Land Development Design And The Schematic Diagram. To Mount The Luminaires, Use Galvanized Steel Lighting Poles Painted In Ral 9011 (Black Graphite), 7.0 M High With Arms In The Same Color, With Arm Lengths Of 1.0 M And 1.5 M And An Inclination Angle Of 10 Degrees. The Designed Poles Should Be Installed On Prefabricated B-60 Concrete Foundations. Led Lighting Fixtures With The Following Ratings Should Be Installed On The Designed Booms On The Side Of The Road And Parking Lot: Light Color 4000K, Luminous Flux Min. 10,200 Lm, Degree Of Tightness Min. Ip 66, Mechanical Resistance Ik 09, Luminous Efficiency Min. 170 Lm/W. In Order To Illuminate The Pedestrian Crossing, Install Lighting Fixtures Adapted To Pedestrian Crossings, With The Following Ratings: Light Color 6000K, Luminous Flux Min. 10,500 Lm, Degree Of Tightness Min. Ip 66, Mechanical Resistance Ik 09, Class A++. On The Side Of The Designed Sidewalk, Install Led Lighting Fixtures With The Following Ratings: Power 40W, Light Color 4000K, Luminous Flux Min. 6,800 Lm, Degree Of Tightness Min. Ip 66, Mechanical Resistance Ik 09, Luminous Efficiency Min. 170 Lm/W. All Factory-Delivered Luminaires Should Be Equipped With Nema 5 Or 7 Vertical Sockets And Adapted To Control A 1-10V Analog Signal, In The Range Of 20-100% At Cosφ≥0.95. Fixtures Painted Ral 9011. All Fixtures Should Be Equipped With Lighting Controllers, Such As Telensa Or Smartly.City.4. Protection And Reconstruction Of Underground Networks Colliding With The Planned Investment.5. Changing The Existing Traffic Organization. Note: If The Swz Or Annexes To The Swz, Including Design Documentation Or Technical Specifications For The Execution And Acceptance Of Works, Would Indicate Trademarks, Origins, Technical Approval Standards, Patents In Relation To Certain Materials And Devices, The Ordering Party, In Accordance With Art. 99(5) Of The Public Procurement Act Allows The Submission Of Equivalent Products. All Products From Specific Manufacturers Specify The Minimum Quality Parameters And Functional Features That The Goods Must Meet In Order To Meet The Requirements Set By The Ordering Party And Constitute Only A Quality Standard Of The Subject Of The Order. By The Provision Regarding The Minimum Requirements For Quality Parameters, The Ordering Party Understands The Requirements Of The Goods Contained In Publicly Available Sources, Catalogs And Manufacturers Websites. The Use Of Exemplary Manufacturers Names Is Only Intended To Clarify The Level Of Expectations Of The Ordering Party In Relation To A Specific Solution. Therefore, The Use Of Manufacturer/Product Names Is For Example Purposes Only. When Describing The Subject Of The Order, The Ordering Party, Indicating The Name Of A Specific Manufacturer (Supplier) Or A Specific Product, Also Allows Equivalent Products With Quality And Performance Parameters. Equivalent Materials Must Be Mentioned By Name In The Offer, And The Burden Of Proving That The Parameters Required By The Ordering Party Are Met Rests With The Person Submitting The Offer. Equivalent Materials Cannot In Any Way Lower The Standard And Cannot Change The Principles And Technical Solutions Adopted In The Design Documentation, And Therefore Cannot Result In The Need To Redesign Any Elements, Nor Can They Deprive The User Of Any Performance, Functionality, Or Usability Described Or Resulting From The Design Documentation. . The Contractor Submitting An Equivalent Offer Will Be Obliged To Prove To The Ordering Party That The Equipment Or Materials It Offers Are Equivalent To Those Proposed In The Project. The Contractor Will Present The Necessary Information Regarding The Materials Accepted For The Offer, Confirming The Equivalence Of The Offered Devices In Relation To Those Proposed In The Project. The Implementation Of The Subject Of The Order Must Be Consistent With The Offer And Swz, In Particular With: A) Technical Documentation (Chapter Iii), B) Important Provisions Of The Contract ( Chapter Iv), C) Bills Of Quantities (Chapter Ii) - The Bill Of Quantities Is Of An Auxiliary Nature.