Tenders Are Invited For Structure Estimation Apparatus - Universal Tribometer

Structure Estimation Apparatus - Universal Tribometer. Subject Of Purchase: Total Quantity: 1 New, Research-Quality And Accurate Tribological For The Delivery, Installation And Commissioning Of A Material Testing System (System), Requests An Offer To Teach How To Use It. The System Is New, If All Its Elements Are Put Into Operation For The First Time Location: It Was Not Previously Deployed/Commissioned Either In Hungary Or In Hungary It Was Not Abroad, Nor Was It Used As A Demonstration Or Test Device. Ak Informs Ats, That The Information Contained In The Call For Proposals, As Well As In Other Public Procurement Documents, To A Specific Standard Or To The Product, Only A Clear Definition Of The Nature Of The Object Was Done For Ak 321/2015. (X. 30.) Paragraphs (3)-(6) Of Section 46 Of Government Decree Based On A Product That Is Equivalent In All Respects To It - Or To An Equivalent Standard Compliance - Accepts, As Long As It Meets The Minimum Requirements It Fits. At The Same Time, The Verification Of Equivalence Is Ats Task And Risk. Ak A As A Result Of This Public Procurement Procedure, 1 Piece Of Research Quality And Accuracy Wishes To Purchase A Tribological Material Testing System (System), Which Is In Contact With Each Other, Performing A Relative Displacement On The Contact Surfaces Relative To Each Other, And The Contact The Friction Conditions Of The Contact Surface Of Bodies Loaded Perpendicular To Surfaces, As Well As It Is Able To Examine The Degradation Of The Surface, And The Contact Surfaces Are Also Suitable Also To Test The Lubricity Of The Optional Lubricant Between Main Parameters: • Be Capable Of The Most General, Standard Examination Of Body Geometries And Movements In Addition To The Aforementioned Friction Conditions And Surface Degradation, I.E. Be Suitable For Pin-On-Disc, Pin-On-Plate, Ball-On-Disc, Ball-On-Plate, To Carry Out Tests At Different Temperatures; • Tribological Contact Rectilinear, Alternating Relative Movement Of The Contact Patch, As Well As The Tribological The Rotating Relative Movement Of A Contact Patch (Around An Axis Outside The Patch) Is A Direction Or Alternate Direction, Can Create; • The Rectilinear, Alternating Ball-On-Plate, Pin-On-Plate, And Around An Axis Outside The Contact Patch Rotating Relative Motion Pin-On-Disc, Ball-On-Disc, In The Case Of Tests On The Measurable Contact Load That Can Be Applied: It Must Be Adjustable In The Range Of At Least 5 N - 3000 N; • The Straight Line Frequency Of Ball-On-Plate And Pin-On-Plate Tests With Linear, Alternating Motion Its Maximum Should Be At Least 80 Hz; • The Ball-On-Plate With Rectilinear, Alternating Direction Movement, In The Case Of Pin-On-Plate Tests, The Adjustable Amplitude Range Of The Contact Patch Displacement Be At Least Between 0.1 - 25 Mm; • The Speed (Pin-On-Disc, Ball-On-Disc, In The Case Of Tests) For Continuous Rotating Movement In The Range Of At Least 0.1 - 6000 Revolutions/Minute Be Changeable; • The Specimen Table, For Which The Specimens With A Flat Surface (Plate, Disc) Are Placed Are Fixed, It Should Be Movable Parallel To The Table Plane, On The One Hand, The Ball/Pin In The Y Line Of Its Rectilinear Alternating Direction Movement, And On The Other Hand, X Perpendicular To It In The Direction So That The Maximum Motorized Displacement In The Y Direction Is At Least 250 Mm Let O So That The Maximum Motorized Displacement In The X Direction Is At Least 125 Mm; • The Existence Of Control Of The Test Temperatures (All Linear, Alternating In The Case Of Directional Or All-Rotational Tests) Requirement (At Least 500°C); • The Acoustic Sensor(S) Should Be Able To Detect At Least The 0.2-5 Mhz Range; • The Resolution Of The Positioning Transmitter In The O Y Direction Is Less Than Or Equal To 1 Μm, O Z Be Less Than Or Equal To 0.1 Μm In Direction; • By Measuring The Contact Resistance Ultra Low Resistance (Both Linear, Alternating, And All Rotating In The Case Of Motion Tests) Can Be Determined With A Resolution Of 1 Μω; • The Contact Measurement Low Noise, So That The Input Impedance Is Below 10 V At Least 10 Gω, While In The 100 V - 1000 V Range It Must Be At Least 10 Mω; • The Temperature Measurement Resolution Must Be At Least 0.1 °C. To Be Delivered As Part Of The System Control Electronics And Control Software In Accordance With The Specifications In The Technical Description, Control Computer And Accessories (Test Specimens, Clamp, External Vibration). Furthermore, The Also Documentation To Be Delivered With The System, Which/Which Description Of Use, Management/Maintenance Instructions And Installation Information Are/Are Included (English And/Or In Hungarian) Conditions, Tasks: • Performance: O Delivery And Installation (At Is Carried Out At Aks Location Specified As The Place Of Performance) And O Commissioning - Where Ak Also Participates - At Is Performed At Aks Location Specified As The Place Of Performance, The Contract 6 Months From The Date Of Entry Into Force; O Training (At The Site Specified As The Place Of Performance By Ak) Min. 2 Working Days (8 Lessons/Working Day; 45 Minutes/Lesson), For Min. 3 People; From Commissioning Within 1 Month • Completion Deadline From The Conclusion Of The Contract 7 Months (If This Is Not A Working Day, Then The First Working Day After That). • Warranty O Service Work - Start Of The System By The Dedicated Contact Person: Starting From The Notification Within 72 Hours. 18 Months From Commissioning Dedicated Contact: At Named At The Time Of The Conclusion Of The Contract, Expressly For This Contract Warranty In The Event Of Problems Arising Within The Scope Of His Obligations, Restrictions On Working Days For Ak Without, A Directly Available Specialist Who Will Start Within The Prescribed Deadline The Service Works. Exact Parameters And Details Of The Expected Performance Are In The Public Procurement In The Technical Description And Draft Contract Issued As Part Of The Documents.