Tenders Are Invited For Adaptation Of Rooms For Computed Tomography Laboratories

The Subject Of The Contract Is The Renovation And Adaptation Of The Room No. D 1.19 Marked On The Attached Ground Floor Plan Of Segments A And D, Drawing Pw-A 386/4, For Computed Tomography Laboratories And The Control Room No. D 1.17 And The Darkroom Room No. D 1.32. In The Complex Of Health Care Centers In Czarnków. The Scope Of Works Includes: 1. Removal Of Existing Covers On Walls And Ceilings.2. Execution Of Electrical Installations (Power Supply For The New Tomograph With Connection To The Ups. 3. Painting The Existing Bathroom With Replacement Of White Sanitary Fittings And Renovation And Reconstruction Of The Control Room And Darkroom No. D 1.17 And No. D 1.32.4. Replacement Of Anti-Static Pvc Lining. 5. Installation Shields Against Ionizing Radiation - In Accordance With The Design Of The Shields, Which Is An Integral Part Of The Subject Of The Contract.6. Replacement Of The Window Transom And Doors In Accordance With The Design Of The Shields.7. Delivery And Assembly Of The Air Conditioning System With An Outdoor Unit Located On The Roof Of The Building Above Room D 2.22 And A Cassette Indoor Unit Mounted On The Ceiling In Room D 1.19.8. Delivery And Installation Of A 120 Kva Ups In The Basement Room No. D 0.06, Annex, Basement Plan, Drawing No. Pw-A 386/3.9. Implementation Of A New Power Supply With A 5*75 Cable From The Rg Located In The Basement Room No. D 0.01 To The Ups And To The Tomograph 10. Replacement Of The Lighting Installation And Electrical Sockets, Switches, Lighting Fixtures With Led Fixtures, Etc.11. Replacement Of Warning Lamps, Emergency Lighting And Safety Switches.12. Installation Of A New Electrical Switchgear Equipped With Protections In Accordance With The Tk Devices Dtr In The Tomography Laboratory. 13. Installation Of A Photo Wallpaper With Dimensions Min 5*2.5 M Description Of The Existing Condition: The Rooms In Which The Renovation Is To Be Carried Out Currently Serve As Rooms For The Ct Workshop And Service Rooms. The Walls Of The Rooms Are Made Of Silicate Brick 25 Cm Thick And Plastered With Cement-Lime Plaster From The Outside, And From The Inside Of The Room Where The Tomograph Is To Be Installed, Radiological Shields Are Installed, Which Do Not Meet The Current Regulations And Should Be Replaced In Accordance With The Shield Design. The Ceiling Structure Above The Studio Is Made Of Hollow Concrete Slabs. The Ceiling Under The Ct Studio Is Reinforced And Does Not Require Reconstruction. The New Apparatus Is Heavier Than The One Used So Far And There Is No Need To Strengthen It. The Ceiling Under The Other Rooms Is Made Of Hollow-Core Slabs Of Various Spans With Pvc Floor Coverings. The Degree Of Wear Of The Floors Is Significant And They Are Replaced With Anti-Electrostatic Ones. In The Workshop There Are Mechanical Ventilation Ducts With A Variable Cross-Section Made Of Galvanized Steel Sheet. The Installation Is Operational, Only Maintenance Needs To Be Carried Out. The Studio Also Has An Electrical Installation And A Water And Sewage System To Which Washbasins Are Connected. There Is A Toilet For Patients Next To The Laboratory, Accessible From The General Communication And From The Room Of The Laboratory. 1.74 M2 - Control Room 5.4 M2 - Darkroom 5.93 M2 Architectural And Construction Solutions: Walling Up And Demolition No Demolition Is Planned As Part Of The Renovation. All Doors And Transoms In The Rooms In Question Should Be Dismantled And New Ones Made In Accordance With The Design Of Radiological Shields. Internal Walls Wall And Ceiling Surfaces Of The Ct Room Should Be Dismantled If The Radiological Shields Do Not Comply With The Regulations And New Ones Should Be Installed In Accordance With The Shield Design. Between The Control Room And The Darkroom, The Door Must Be Dismantled And The Partition Wall Dismantled. Walls And Ceilings Should Be Puttied And Painted With Washable Paints. Floors In All Rooms, The Old, Damaged Pvc Floor Covering Should Be Removed And A New Smoothing Layer Made Of Self-Leveling, Non-Shrinking Mass, 0.5 Cm Thick, Should Be Made. A New Anti-Electrostatic Floor Covering Adapted To This Type Of Rooms With A High Abrasion Class Should Be Glued On The Floor Prepared In This Way. Ceilings. Filling And Painting With Acrylic Paints Should Be Carried Out, And Radiological Shields Should Be Made In The Ct Room In Accordance With The Design. For Paper Towels And A Waste Basket. The Existing Floor Should Be Hammered Off And A New Self-Levelling Leveling Layer Should Be Made With Anti-Moisture Insulation In Accordance With The Manufacturers Technology. Use Non-Slip Gres Tiles As The Finishing Layer. The Walls Are Lined With Ceramic Tiles To The Entire Height Of The Room. Ventilation Will Be An Exhaust System Mechanically Supported By A Duct Fan Ensuring 1.5-Fold Air Exchange. Door And Window Joinery Doors And Fanlights To The Laboratory And In The Laboratory Should Be Made In The Bkt System In Accordance With The Design Of Radiological Shields. Electrical Installation 1. Low-Voltage Distribution Network 0.4Kv Power Supply To The Rooms Of The Computer Tomography Laboratory Will Be Provided From The Main Switchboard Of The R-Gw Hospital. The R-Gw Switchgear Is Powered From A Consumer Transformer Station, And The Station (In Its Entirety) Is Reserved With A Power Generator. The R-Gw Switchgear Is Installed In The Basement, In The Vicinity Of The Tomograph Room.2. Power Supply For Medical Equipment For The Proper Operation Of Computed Tomography Devices, An Emergency Power Supply, The So-Called Emergency Power Supply, Should Be Used. Ups, With A Minimum Power Of 120Kva And A Backup Time Of Min. 10 Minutes. Thanks To Its Function, The Ups Guarantees Uninterrupted Operation Of Devices And Protects Them Against The Effects Of Unexpected Surges Or Voltage Fluctuations. The Planned Ups Should Be Installed In A Room In The Basement, In The Immediate Vicinity Of The Existing R-Gw Switchgear. Together With The Ups, A Service By-Pass (External) Should Be Installed To Enable Periodic (Or Emergency) Maintenance Of The Ups Without The Need To Turn Off The Power To The Devices. The Existing Yky 5X70mm Cable Laid Between The R-Gw Switchgear And The Laboratory Rooms Should Be Used To Power The New Computed Tomography Apparatus. Therefore, The Above-Mentioned The Cable Should Be Cut, Extended And Inserted Into The By-Pass Installed In The Basement (At The Ups). The Rest Of The Cable Should Be Inserted Into The Devices Of The New Ct Scanner. All Works Must Be Carried Out In Accordance With Applicable Regulations And Standards, After The Works Are Completed, Post-Assembly Tests Should Be Carried Out And The Results Recorded In Reports. The Employer Requires That All Materials Used Have Certificates Allowing Them To Be Used In Health Care Facilities. The Detailed Scope Of Performance Of The Subject Of The Contract Is Included In The Documentation Attached To The Swz:1. Ground Floor Plan Pw-A 386/42. Basement Plan Pw-A 386/33. Design Of Fixed Shields4. Sanitary Opinion5. Bill Of Quantities And Offer Cost Estimate