Tenders Are Invited For Establishment Of A Closed-Type Pneumatic Shooting Range In The School Complex No. 2 In Sanok

The Scope Of Works Includes: Modernization Of The Pneumatic Shooting Range In The School Complex No. 2 In Sanok. The Construction Works Include In Particular: 1) Securing The Walls Of Closed Rooms Constituting The Place Where The Shooting Targets And Shot Catchers Are Attached Against Damage And Destruction During Shooting, Aiming At The Same Time To Minimize The Formation Of The So-Called Uncontrolled Ricochets. For This Purpose, It Is Planned To Make A Forward-Leaning Wall Made Of Fir Boards, Th. 5.0 Cm Behind The Second Target, 15.0 M Away From The Shooting Position. 2) Adaptation Of The Walls Of Closed Rooms Along The Shooting Sectors (Side Walls) In Terms Of Absorbing The Energy Of The Shot Shot, I.E. Preventing The Phenomenon Of Ricocheting (Rebounding) Of The Shot, - It Is Planned To Supplement Cement Plaster - Lime Plaster On The Walls, Casing The Walls With Windows With Osb Boards Covered With Gkf Boards, Installation Of Window Blinds. 3) Adaptation Of The Electrical Installation Of The Room To Operate The Devices Transporting The Shooting Targets (Target Conveyors), To Ensure Proper Lighting Of The Main Room And Spot Lighting Of The Shooting Targets, Consisting In The Implementation Of A Completely New Electrical Lighting Installation, Sockets, And Including The Execution Of Power Supply For The Drives Serving The Target Strings Above The Pneumatic Counter Fastened To The So-Called Starting Beam, Lighting Shooting Targets With Adjustable Lamps, Main, Emergency And Evacuation Lighting. 4) Adaptation Of The Floor Of A Closed Room And The Selection Of An Appropriate Floor Or Lining Enabling Quick And Easy Removal Of Shot Fired During Shooting, Consisting In Tearing Off The Old Floor And Making A New Floor For Laying The Pvc Lining. 2.0 Mm Thick With A 0.8 Mm Wear Layer Adapted For Use In Public Utility Buildings, Certified For Medium Traffic. 5) Adaptation Of A Closed Room For Servicing Pneumatic Devices (Air Rifles, Air Guns) And Additional Equipment (E.G. Protective Glasses, Gas Cylinders) And Accessories (E.G. Shooting Targets, Pellets, Spare Accessories For Devices Transporting Targets) Necessary For Shooting In In A Way That Prevents Access By Unauthorized (Third) Persons, Lockable With A Patent Key Or Padlock. A Room Behind The Shooting Range Has Been Designed, Equipped With A Steel Workbench With A Vice For The Maintenance Of Shooting Devices, Which Is Also A Place For Preparing Pneumatic Devices For Shooting. 6) Renovation Of Sanitary Facilities (To Be Used Only During The Implementation Of Training Projects At The Shooting Range); Consisting In The Demolition Of The Existing Partition Walls And The Implementation Of A Completely New Arrangement Of Rooms Allowing For The Construction Of Separate Sanitary Facilities For Men And Women. A New Floor, Plaster And Wall Cladding With Tiles Will Be Removed And Made, Dismantling Of The Old Electrical, Water And Sewage System And Installation Of A New One, Connection Of Ventilation. 7) Renovation Of The Corridor Including The Entrance To The Shooting Range, Sanitary Facilities, And Installation Of Cabinets For Outer Clothing For Participants Of Shooting Classes - Renovation Of Walls And Floor. Purchase And Delivery Of Cloakroom Lockers For Approx. 32 People. 8) Barriers Between The Positions, I.E. Screens Separating Individual Shooting Positions; Covers Made Of Polycarbonate Are To Be Used. 9) Ventilation (Air-Conditioning) Devices To Improve Shooting Conditions In The Room; Consisting In The Installation Of A Wall Recuperator With A Capacity Of Min. 185M3 10) Screens For Windows In The Form Of Blinds Or Roller Blinds Limiting The Access Of Daylight; Consisting In The Assembly Of Window Blinds (135X90) With A Manual Drive 11) A Place For Preparing Pneumatic Devices For Shooting And Service After Shooting, Equipped With Equipment And Materials For Their Operation And Maintenance 12) Renovation Of The Room Behind The Shooting Range. The Task Also Includes The Purchase Of Shooting Range Equipment: 1) Pneumatic Devices - Pcp Air Rifles Powered By A Cartridge With A Pressure Of 300 Bar, Generating The Initial Kinetic Energy Of The Shot In The Range Above 7.5 To 17 J (Jouli), Not Requiring A Permit Under The Provisions Of The Act On Weapons And Ammunition - 1 Set For One Shooting Position, These Devices Should Be Equipped With Aiming Devices: Diopter Type. 2) Pneumatic Devices - Pneumatic Guns Caliber 4.5 Mm, Powered By A Cartridge With A Pressure Of 200 Bar, Generating The Initial Kinetic Energy Of The Shot In The Range Above 7.5 To 17 J (Jouli), Not Requiring A Permit Under The Provisions Of The Act On Weapons And Ammunition - 1 Set. For One Shooting Position, A Device Equipped With Sights: A Front Sight And A Rear Sight (4 Pistols For Right-Handers And 1 Pistol For Left-Handers Should Be Purchased And Delivered.) 3) Shot Catchers (Bullet Traps) - Deliver And Install 5 Sets. Permanent Bullet Traps On The Board Cover Wall Set At The End Of The Room (15 M From The Line Of Fire), And Five Bullet Traps Mounted On Movable Stands To Complete The Set Shooter - 1 Kpi. For One Shooting Position (Five In Total), A Device With A Top Drive (Ropes Stretched Under The Ceiling) Should Be Delivered And Installed, The Set Consists Of A Drive Unit Mounted On A Beam Above The Pneumatic Counters, Cables, A Trolley With A Target And Target Holder. 5) Devices For Illuminating Shooting Targets - 1 Set. For One Shooting Position, Use Lighting Lamps Dedicated To Target Illumination, Mounted To The Bullet Trap Stand Or To The Bullet Trap. 6) Pneumatic Counter (Shooting Platform) Located Perpendicularly To All Shooting Positions, Constituting At The Same Time The Line Of Opening Fire And The Line Of Shooting Positions For All Shooting People - Delivery And Assembly Of 2 Sets Was Designed. Two-Stand Counters And 1 Set. One-Stand 7) Table For The Instructor (Shooting) 1 Pc. A Steel Workbench With A Vice Should Be Purchased And Delivered, Additional Equipment Is A 4-Drawer Cabinet With A Pencil Case And A Central Lock, A Door Cabinet With A Patent Lock, 8) Medical Kit With First Aid Equipment - 1 Set. First Aid Kit With A Frame That Attaches To The Wall. Equipped In Accordance With The German Din 13157 Standard. (Din 13157 Standard Is An Industrial Standard Specifying The Number And Type Of Articles Necessary To Provide First Aid At The Workplace, Office, School Or Institution) 9) Information Board - 1 Item, 10) Approved And Regulations For Using The Pneumatic Shooting Range Displayed In A Visible Place On The Board - 1 Set. 11) Approved And Displayed On The Board In A Visible Place Safety Conditions While Staying At The Pneumatic Shooting Range - 1 Set, 12) Protective Glasses - 2 Pcs. Per One Shooting Position, (10 Pcs In Total) 13) Protective Glasses For The Instructor (Leading The Shooting) — 2 Pcs., 14) Pellets With A Diameter Adapted To The Purchased Equipment (4.5Mm) 1,000 Pcs. For Each Shooting Position, 15) Shooting Targets - 50 Pcs. For Each Shooting Position, 16) Lockable Cabinet For Storing Weapons And Shooting Accessories With A Lock Or Padlock Preventing Direct Access By Third Parties (Unauthorised). A Detailed Description Of The Subject Of The Contract Is Contained In Appendix No. 1 To The Tor - Detailed Description Of The Subject Of The Contract.