Tenders Are Invited For Thermomodernization Of The Municipal Building Of The Krosno Poviat Located In Miejsce Piastowe Co-Financed By Wfośi Gw In Rzeszów In The Field Of Improving Air Quality.

1. The Subject Of The Contract Is Thermomodernization Of The Municipal Building Of The Krosno Poviat Located In Miejsce Piastowe Co-Financed By The Provincial Fund For Environmental Protection And Water Management In Rzeszów In The Field Of Air Quality Improvement. The Task Includes, Among Others: I. Central Heating Thermomodernization And Hot Water In The Scope Of - Liquidation Of The Existing Viessmann Boiler, Type Atola, Atmospheric Gas, 28Kw, Manufactured In 1994, 1 Pc., Construction Of A New Boiler House Based On A 38Kw Condensing Boiler, 94% Efficiency Or Equivalent The Change In The Boiler Power From 28Kw To 38Kw Results From The Fact That So Far Some Of The Buildings Rooms Have Been Heated Separately; After The Modernization There Will Be One Heating Unit For The Entire Building. - Implementation Of A New Central Heating System And Hot Water In The Scope Of: Replacement Of Radiators (30 Pcs.), 196 M Piping, Installation Of Thermostatic Valves (30 Pcs.), Connection For The Installation Of A New Boiler, Purchase And Installation Of A 300 L Hot Water Tank.Ii. Thermal Modernization Of The Building Envelope Based On An Energy Audit, The Optimal Variant Of The Project: 1. Modernization Of The External Door Partition Replacement Of The Existing Door With The Coefficient W/(M2•K) 2.5 For New Doors With The Coefficient W/(M2•K) 1.3- Total Area Of ​​The Door Before/After Modernization 8.22 M2 (3 Pcs. )2. Modernization Of The Partition Window Joinery Replacement Of Existing External Windows With A W/(M2•K) Coefficient Of 1.8 For New Windows With A W/(M2•K) Coefficient Of 0.9-Required U-Factor For New Joinery: 0.900 W/(M2•K) ) - Total Area Of ​​Windows Before/After Modernization 45.16 M2 (32 Pcs.)3. Modernization Of The Partition Flat Roof - Insulation With A Sandwich Panel With A Thickness Of 25 Cm And Λ = 0.038 W/M2k (Or Equivalent) To Obtain The Coefficient W/(M2•K) 0.13 Together With Insulation With Roofing Felt - Partition Area To Be Insulated 147.03 M2 4. Modernization Of The Partition Wall In The Ground Foundation Applied Thermal Insulation Material: Xps Polystyrene, Thickness. 8 Cm And Λ = 0.035 W/M2k (Or Equivalent) To Obtain The Coefficient W/(M2•K) 0.25- Partition Area For Insulation 54.80 M2ii. Central Heating Thermomodernization And Hot Water 1. Modernization Of The Heating And Hot Water System In The Scope Of - Liquidation Of The Existing Viessmann Boiler, Type Atola, Atmospheric Gas, 28Kw, Year Of Manufacture 1994, 1 Pc., Construction Of A New Boiler House Based On A 38Kw Condensing Boiler And 94% Efficiency, Or Equivalent-Execution Of A New Central Heating Installation And Hot Water In The Scope Of: Replacement Of Radiators (30 Pcs.), 196 M Piping, Installation Of Thermostatic Valves (30 Pcs.), Connection For The Installation Of A New Boiler, Purchase And Installation Of A 300 L Hot Water Tank. Iii. Renovation Of Sanitary Facilities. Iv. Modernization Of The Water And Sewage System And The Electrical System, Including The Lightning Protection System. 2. A Detailed Description Of The Elements Of The Subject Of The Order Is Provided In The Technical Documentation And Bills Of Quantities Constituting Annex No. 4 To Swz.3. If The Documentation Would Indicate Trademarks, Patents Or Origin In Relation To Certain Materials And Devices, The Ordering Party, In Accordance With Art. 99 Sec. 5 Of The Act, Allows The Submission Of Equivalent Products. All Products From Specific Manufacturers Define The Minimum Quality Parameters And Functional Characteristics That The Goods Must Meet In Order To Meet The Requirements Set By The Ordering Party And Constitute Only A Quality Standard Of The Subject Of The Order. By The Provision Regarding The Minimum Requirements Of Quality Parameters, The Ordering Party Understands The Requirements Of The Goods Contained In Publicly Available Sources, Catalogs, Manufacturers Websites. The Use Of Exemplary Names Of The Manufacturer Is Only Intended To Clarify The Level Of Expectations Of The Ordering Party In Relation To A Specific Solution. Thus, The Use Of The Names Of Manufacturers / Products / Is Only Exemplary. The Contracting Authority, When Describing The Subject Of The Contract, Indicating The Designation Of A Specific Manufacturer (Supplier) Or A Specific Product, At The Same Time Allows Equivalent Products With Quality Parameters And Functional Characteristics, At Least At The Level Of The Parameters Of The Indicated Product, Thus Recognizing Each Product With The Indicated Parameters Or Better. In Such A Situation, The Ordering Party Requires The Submission Of Relevant Documents (Together With The Offer) To Authenticate These Materials Or Devices. They Will Be Subject To Evaluation By The Ordering Party, Which Will Be The Basis For The Ordering Party To Make A Decision On Accepting The Equivalents. The Ordering Party Reserves The Right To Ask The Author Of The Project Documentation For An Opinion On The Offered Materials Or Devices. If The Contractor Fails To Submit Documents On The Use Of Other Materials And Devices, It Shall Be Understood That The Materials And Devices Proposed In The Description Of The Subject Of The Order Have Been Included In The Calculation Of The Tender Price.4. Describing The Subject Of The Contract In The Attached Detailed Description Of The Subject Of The Contract By Reference To The Standards, Technical Assessments, Technical Specifications And Technical Reference Systems Referred To In Art. 101 Sec. 1 Point 2 And Sec. 3 Of The Public Procurement Law, The Ordering Party Allows Solutions Equivalent To Those Described, And Each Such Description Is Accompanied By The Words Or Equivalent.