Tenders Are Invited For Procurement Of Operating Tables

Tenders Are Invited For Procurement Of Operating Tables. 1 Operating Table (Electrically Controllable) 1. The Operating Table Is Designed To Be Used In General Surgery, Urology, Gynecology, Orthopedics, Neurosurgery, Thoracic-Cardiac, Ent And Many Similar Operations And Should Have Many Different Accessories. 2. Locks And Fixing Screw Heads Of Operating Tables Must Be Made Of Stainless Steel To Avoid Bacteria. 3. The Table Top Should Consist Of Six Parts: Head, Two-Part Back, Seat And Foot Part. These Parts Must Be Able To Move Independently Of Each Other. 4. The Body Of The Operating Table Should Be Made Of Acid-Resistant, High-Quality 316 Stainless Steel Material. 5. Above The Operating Table, There Should Be A Polyurethane Cushion, At Least 60 Mm Thick, Made Of A Single Piece Of Fluid-Resistant, Seamless And Compact Material. 6. The Operating Table Should Have A Polyurethane Cushion And An Ergonomic Concave Shape For The Comfort Of The Patient. 7. The Material Supporting The Pad On The Operating Table Should Be X-Ray Transparent And Compact Material. X-Rays Should Be Available Anywhere On The Operating Table. 8. The Base Of The Operating Table Should Be Designed In A "T" Shape, Which Allows The Operator To Approach The Table Better, And The Upper Part Should Be At Least 75% Imageable With The C-Arm (Scopy) System. 9. The Dimensions Of The Operating Table Should Be As Follows; Width : 610 Mm, (+/- 30Mm) (With Cushion) Length : 2160 Mm, (+/-30Mm) (With Cushion) Height: Min. 820 Mm Max. 1215 Mm, (+/-30Mm) 10. All Electrical And Electronic Components Of The Operating Table Must Have Ipx4 Protection Class. 11. Operating Table, Height, Back, Trendelenburg / Reverse Trendelenburg, Flex / Reflex, Side Bending (Right And Left Bending) And Sliding Movements Should Be Performed By Electromechanical Systems. 12. The Operating Table Should Consist Of 2 Separate Remote Controls, A Wired Hand Remote Control And A Body Control Remote Control. A. Hand Control: A.1. Must Know How To Take The Basic Postures Of The Operating Table With 12 Different Function Keys. A.2. Must Lose 4 Different Stances And Be Able To Restore Them With One Click. A.3. Must Be Able To Flex With A Dedicated Button And Reflex With A Button. The Symbols Of These Actions Should Be On The Remote Control. A.4. It Should Be Able To Provide Reset Position (Cpr Position) With 1 Dedicated Button. A.5. The Hand Control Should Be Powered By The Tables Internal Battery, And Should Not Require An Additional Battery Or Charging. A.6. The Hand Control Shall Have A Key Lock Button And Shall Be Indicated By This Light When The Key Lock Button Is Activated. A.7. The Hand Control Should Have A Three-Stage Battery Indicator And A Charging Connection Indicator. 8. The Hand Control Must Have A Malfunction Warning Indicator. B. Body Control Remote. B.1. It Should Be Able To Give A Reset Position (Cpr Position) With A Special Button. B.2. It Should Be Able To Reach The Basic Postures Of The Operating Table With 10 Different Function Keys. B.3. The Body Control Shall Have A Key Lock Button And Shall Be Illuminated When The Key Lock Is Activated. B.4. The Body Control Panel Should Have A Three-Stage Battery Indicator And A Charging Connection Indicator. B.5. The Body Control Panel Should Have A Malfunction Warning Indicator. 2. The Hand Control Set Should Be Made Of Impact And Drop Resistant Plastic Material And Should Be Extendable To At Least 2 Meters With A Spiral Cable. The Lighting Should Be Activated When The Button On The Hand Control Is Pressed. 3. Actions Of The Operating Table Should Have The Following Values: A. The Head Of The Operating Table Is Mechanically Adjustable With A Hydraulic Gas Piston And Must Be Completely Removable From The Table. The Head Part Should Be Able To Take A Position Of 60 Degrees (+/-5 °) Down, 30 Degrees Up (+/-5 °) And Should Be Fixed At The Desired Point. B. The Rear Part, Which Can Be Controlled By A Wired Hand Control, Should Be Able To Move Up 90 Degrees (+/-5°) And Down 40 Degrees (+/-5°). For The Kidney Surgery Position, The Back Of The Operating Table Should Consist Of Two Parts. C. The Kidney Booster Should Be Fixed To The Head Of The Operating Table With The Help Of A Mechanically Attached And Removable Arm, Allowing The Patients Body To Be Lifted And Anatomically Positioned. The Renal Surgery Position Mechanical Lift Of The Operating Table Must Be Able To Rise At Least 12 Cm. D. The Operating Table Must Be Capable Of 25 Degrees (+/-5°) Trendelenburg And 25 Degrees (+/-5°) Reverse Trendelenburg Movement. E. The Operating Table Should Be Adjustable For Lateral Tilt Movement Of 20 Degrees (+/-5°) To The Left And -20 Degrees (+/-5°) To The Right. F. The Table Top Should Be Able To Slide At Least 30 Cm. G. The Legs Of The Operating Table Must Be Mechanically Adjustable And Completely Removable From The Table. The Right And Left Legs Of The Operating Table Are Independent Of Each Other And Should Be Able To Move In The Vertical And Horizontal Planes. Every Foot Soot. Tender Fees: Azn 250/- Non Refundable. [Disclaimer: The Above Text Is Machine Translated. For Accurate Information Kindly Refer The Original Document.] Tender Link :