Tenders Are Invited For Procurement Of Fire Crash

Tenders Are Invited For Procurement Of Fire Crash 1. Model Of Latest Model, (Super Structure) Origin Of Firefighting System From Austria, Belgium, France, Germany, Netherlands, Switzerland, Italy, Spain, Usa, Uk & Japan. 2. Capacity Minimum 9000 Ltrs Water + 1000 Ltrs Foam And Dcp 250 Kg 3. Carrier Latest Model (Western Europe / Usa / Uk / Japan) 3.1. Transmission 3.2. (Performancesfull Load) Auto Transmission (Electronically Control) Power Take Off (Electrically & Manual Operated) 3.3. Engine Euro Standard, Diesel 4 Stroke Front 3.4. Displacement Minimum 12000 Cc 3.5. Output Power Minimum 390- Kw (500) Hp @ 1,600 Rpm 3.6. Drive Line Automatic Gear Shift System 3.7. Clutch Dry Single Disc- 430 Mm Or Better 3.8. Front/ 1St Rear / 2 Nd Rear Axles Minimum 9.0 Ton/ 13 Ton/13 Ton 3.9. Differential Lock Inter Wheels And Inter Axles DriveS Selectable 3.10. Chassis 3.11. Steering Position / Type Right Hand Drive / Power Assisted 3.12. Suspension Front / Rear Spring Leafs, Parabolic Type 3.13. Wheel Front / Rear Single, 1St Rear & 2Nd Rear Single In Line 3.14. Tyres Size/ Design Type 365/85 R20, Single At Front And Rear Axles / Cross Country 3.15. Exhaust System The Exhaust Shall Be Constructed In Such A Manner That Exhaust Discharge Is Directed Away From Any Operator 3.16. Towing Eyes The Truck Is To Be Fitted With Heavy Duty Front & Rear Recovery Eyes. 3.17. Cabin 3.18. Type Forward Control Type, C/W Hydraulic Tilting Device 3.19. Seats Four (04) (Driver + 3 Crews). All Seats Are To Be Provided With Seat Belt. A/C Unit / Fog Lights/ Provision For Radio R/T Set 3.20. Fenders The Rear Wheels Are To Be Covered By Fenders, Matching The General Design Of The Vehicle. 3.21. Access Access Steps And Hand Rails Are To Be Provided Wherever Required For The Crew Safety On The Body And In The Cabin. 3.22. Bumper A Single Platform Will Be Provided With Front Bumper For Easy Inspection / Cleanliness Of Wind Screen. 4. General (Super Structure) 4.1. General Features The Artfc Extinguishing Agents And Protective Clothes Shall Meet Stipulation Of The Asm, Part 1 Rescue And Firefighting Third Edition 1990 Of Icao As Applicable. 5. Body A Modular Design Is To Be Adopted In The Body Which Comprises Of The Front Section, The Midsection And The Rear Cabinet. Easily Accessible The Dcp Unit And Auxiliary Equipment. The Midsection Contains The Tanks. The Rear Section Contains The Either Pump And The Piping. 6. Fire Fighting 6.1. Fire Pumps Minimum 4000 Ltrs/Min @ 10 Bar (Medium Pressure) Minimum 400 Ltrs/Min @ 40 Bar (High Pressure) 6.2. Roof Turret / Monitor Discharge Minimum 4000 Ltrs/Min At 10 Bar 6.3. Bumper Turret / Monitor Discharge Minimum 2000 Ltrs/Min At 10 Bar 6.4. High Pressure Hose Reel Discharge Minimum 150 Ltrs/Min 6.5. Under Truck Nozzles Discharge 6X6 Minimum 40 Ltrs/Min (Each) 6.6. Co2 System 100 Kg Co2 System Fitted (A Third Co2 Cylinder As Standby) 7. Fire Fighting Equipment 7.1 Fire / Water Pump Complete Bronze Material Or Better One (Multi Stage), Casing & Impellers Made Of Bronze Or Better One And Pump Shaft Made Of Stainless Steel. 7.2. Priming The Priming Is To Be Fully Automatic 7.3. Pump Drive The Pump Is To Be Driven By Clutch Independent Power Take Off, Which Assure A Full Pump & Roll Capability To The Artfc. 7.4. Flow Minimum 4000 Ltrs/Min @ 10 Bar Normal Pressure And 400 Ltr/Min @ 40 Bar High Pressure 8. Water Tank 8.1. Design And Construction The Tank Is To Be Made Out Of Polypropylene Pph 2464, Or Better One Thickness Minimum 20 Mm. The Whole Roof Has A Non-Skid Surface. The Water Section Is To Be Baffled Into Compartment, Inter Connected At The Tank Bottom Which Orifices Of Suitable Size To Permit The Full Flow. The Tank Is Elastically Mounted On To The Chassis Frame, Restrained From Moving. The Construction Prevents Damages From The Chassis Frame Torsion. 8.2. Tank Fitting Internal Bafflers, With Whole Large Enough To Allow Easy Maintenance And Inspection Of All Sections Of The Tank. Case No. Pacb/751/090921024/1164/P-2 Page 19 Of 32 Two Tank Filling Opening, Complete With 2 ½ Coupling, Mesh Strainer, Ball Valve, Blind Cap And Chain, Located One At Each Side. One Single Bolt Type Man-Hole, Diameter 500 Mm, Located On The Top For Maintenance And Inspection Purpose. One Tank Drain Opening, Complete With 2 ½ Coupling, Ball Valve Blind Cap And Chain, Located At One Side. One Overflow Pipe, Directed Below The Chassis, Behind The Rear Wheels. One Led Bar Type Water Level Gauge At The Dashboard. 9. Foam Concentrate Tank 9.1. Design And Construction The Tank Is To Be Made Out Of Polypropylene Pph 2464, Or Better One Thickness 20 Mm- Integrated In The Water Tank. 9.2. Tank Fitting One Sump, Large Enough To Permit The Entire Contents To Be Available For Extinguishing. One Single Bolt Type Man-Hole, Diameter 500 Mm, Located On The Top For Maintenance And Inspection Purpose. Internal Baffler, With Whole Large Enough To Allow Easy Maintenance And Inspection Of All Sections Of The Tank. One Tank Filling Opening Complete With 2 ½ Coupling Mesh Strainer, Ball Valve, Blind Cap And Chain, Located At One Side. One Pressure / Vacuum Vent Device, Located On The Top. One Led Bar Type Foam Level Gauge At The Dashboard. One Electrically Operated From The Vehicle Batteries, 24 Vdc, Foam Filling Pump To Fill Up The Foam Tank From External Source (I.E. Foam Drums). With 1 ½ Suction Connection With 1 ½ Ball Valve, Quarter Turn Type And 1 ½ Nh Coupling. Minimum Foam Filling Pump Flow Rate 100 Ltrs/Min. 10. Piping 10.1 Construction All Pipes Are To Be Made Out Of Stainless Steel Aisi 316L. Wherever It Is Required, Flexible Connection And Victaulic Coupling 10.2. Valves Provided To Avoid Stresses Into The Piping And To Facilities Removal And Replacement. All Valves Are To Be Quarter-Turn Type. The Drain Valves Will Be Located In Such Positions To Permit The Complete Drainage Of The Tank, Water Pump And Pipes. Ball Valves: Braces Body With Chromium Coated Sphere. Butterfly Valves: Cast Iron Body With Stainless Steel Disc And Trim. 10.3. Couplings All Couplings Are To Be According To Bs/En Standard Each Complete With Blind Cap And Chain, And Made Out Of Brass Or Better One. 10.4. Flushing One Complete Flushing System Will Be Provided, Through Remote Controlled Ball Valve. 11. Foam Proportioning System In Accordance With Nfpa 414 Section 4.16.4. 11.1 Construction The Artfc Is To Be Fitted With An Effective And Reliable Automatic System For Suction And Proportioning Of The Foam Concentrate Into The Water, The Proportioning Rate Is Manually Preset At The Pump Compartment. The Proportioning Valves Are Conveniently Grouped And Clearly Marked. 11.2. Operation The Proportioning System Is To Be Operated Automatically At The Preset Mixing Rate. 12. Roof Monitor (Turret) 12.1 Construction One Low Profile Electric / Hydraulic Remote Controlled Monitor Will Be Installed, Remotely Controlled By A Joy-Stick At The Dashboard. 12.2. Location Roof Monitor Will Be Installed Above The Driver Cabin On The Roof 12.3. Water / Foam Remote Controlled C/W Manual Override. 12.4. Emergency Controls Direct Manual Operation Will Be Possible From The Roof In Case Of Failure Of The Remote Controls. 12.5. Camera A Color Camera Is To Be Provided, Which Will Record The Occurrence. 12.6. Discharge Output Minimum 4000 Ltrs/Min @ 10 Bar 12.7. Throw Water Minimum 90 M 12.8. Throw Foam Minimum 80 M 12.9. Rotation Minimum 330 12.10. Elevation Above/ Below Minimum 70 /- 15 The Quotation Must Be Valid Up To 30-06-2022 Earnest Money : 5 % Closing Date: 21/2/2022 Closing Time: 10:30:00 Am Opening Time: 11:00:00 Am