Tenders are invited for Pipeline Work

Quotation are invited for 1032101043 Pipe Line Work Bil Ha Do Murfx Description pipeline workTECHNICAL AND GENERAL SPECIFICATION OFOUTSOURCING WORK M STATION JEBEL ALIPOWER STATION TITLE REPLACEMENT OF NG BR6 PIPELINE SPOOL APPROX 02 METER AND 01 NO FLANGE PIPE SPECIFICATION DN 600 SCH 40 A106 B FLANGE SPECIFICATION DN 600 CLASS 300 A105 WELD NECK RAISED FACE DURATION 02 DAYSSCHEDULE WORK TO BE DONE DURING MEXTENSION TOTAL SHUTDOWN TENTATIVELYSCHEDULED IN DEC 2021 OR JAN 2022 1 SCOPE OF WORK 1 1 MOBILIZE MEN EQUIPMENT WITHIN 02 DAYSOF ADVANCE NOTICE 1 2 SUBMIT FOLLOWINGDOCUMENTS TO OBTAIN PTW 1 2 1 METHOD STATEMENT1 2 2 RISK ASSESSMENT OF THE WORK1 2 3 TOOLBOX TALK REPORT 1 3 OBTAIN PTW PERMIT TOWORK AND LC LINE CLEARANCE FROM DEWA 1 4 CUT APPROX 02 METER SPOOL EXACT SIZETO BE VERIFIED AT SITE FROM 06 METER SPAREPIPE AVAILABLE AT DEWA 1 5 TRANSPORT THE PIPESPOOL AND 01 NO FLANGE TO CONTRACTORWORKSHOP 1 6 WELD THE PIPE AND FLANGE 1 7 CONDUCT RT OF THE WELD JOINT CONTACTOR SSCOPE 1 8 CARRY OUT SURFACE PREPARATIONAND PAINTING OF PIPE FLANGE 1 9 PAINTSPECIFICATION COLOR YELLOW STANDARD BS 480008 E 53 COATING PAINT DESCRIPTION DFT PRIMER COAT TWO COMPONENT POLYAMINECURED PURE EPOXY COATING PRIMER SOLIDS BY VOLUME MIN 72 OR TWO COMPONENT PHENALKAMINE EPOXYCOATING SOLIDS BY VOLUME MIN 80 75MICRONS 1 1 125 MICRONS MIDCOAT TWO COMPONENT POLYAMINE CUREDPURE EPOXY COATING PRIMER SOLIDS BYVOLUME MIN 72 OR TWO COMPONENT PHENALKAMINE EPOXY COATING SOLIDS BYVOLUME MIN 80 100 MICRONS 1 1 125MICRONS FINAL COAT TWO COMPONENT CHEMICALLY CURING ALIPHATIC ACRYLIC POLYURETHANE COATING SOLIDS BY VOLUME MIN 63 OR TWOCOMPONENT SELF PRIMING ALIPHATIC ACRYLICPOLYURETHANE SOLIDS BY VOLUME MIN 60 75 MICRONS 1 1 50 MICRONS TOTAL DFT MIN 250 300MICRONS 1 10 TRANSPORT BACK THE PIPEWITH FLANGE TO DEWA SITE FOR INSTALLATION 1 11 ENSURESITE AREA IS CORRECTLY SECURED AND SAFE TOWORK ON IN ALL RESPECTS 1 12 ENSUREPROPER ISOLATION OF THE LINE DEWA CHEMISTCLEARANCE FOR LEL IS OBTAINED BEFORE STARTOF WORK 1 13 CONDUCT SITE SURVEY ANDSAFETY INSPECTION TO ASSESS THE WORKING ENVIRONMENT 1 14 IF THE WORKING ENVIRONMENT IS SAFE PROCEED WITH THE FOLLOWING STEPS 1 15 PROVIDETEMPORARY PIPE SUPPORTS AS REQUIRED 1 16 MARK CUT THE PIPE SPOOL BY COLD CUTTING METHOD AND REMOVE IT FROMLOCATION USING CRANE 1 17 EXISTING FLANGE SURFACE WILL BEINSPECTED BY DEWA 1 18 OBTAIN DEWACHEMIST CLEARANCE FOR GRINDING WELDING 1 19 PREPAREWELD EDGE OF EXISTING LINE 1 20 SHIFT THEPRE FABRICATED PIPE TO LOCATION USINGCRANE 1 21 FIT UP THE NEW PRE FABRICATEDPIPE AND ALIGN PROPERLY WITH EXISTING PIPE ANDFLANGE 1 22 WELD THE NEW PIPE 1 23 AFTERWELDING RT OF THE WELD JOINT WILL BEARRANGEDBY DEWA 1 24 GASKET INSTALLATION AND THEFLANGE BOLT TIGHTENING WILL BE DONE BYDEWA 1 25 AFTER FLANGE BOLTS ARETIGHTENED REMOVE TEMPORARY SUPPORTS 1 26 QUALIFIED JOBSUPERVISOR SHALL BE ASSIGNED FOR THE JOB 1 27 SKILLED TECHNICIANS SHALL CARRY OUTALL THE JOBS 1 28 WELD JOINTS TO BE MADE BY QUALIFIED WELDER ACCORDING TO APPLICABLEWPS ASME REQUIREMENTS WPS WELDERCERTIFICATES TO BE PROVIDED 1 29 HOUSEKEEPING ANDDISPOSAL OF WASTE TO BE DONE BEFORE SITECLEARANCE 1 30 DE MOBILIZE MEN ANDEQUIPMENT AFTER COMPLETION OF THE JOB 1 31 COMPLETIONAND TEST REPORT TO BE SUBMITTED TO DEWA REPORT SHALL CONTAIN RELEVANT PHOTOS 1 32 ALLTOOLS TACKLES ARE IN CONTRACTOR S SCOPE 1 33 PROPER AND TESTED TOOLS TO BE USED 1 34 ALL LIFTING POWER TOOLS SHALL HAVEVALID 3RD PARTY TEST CERTIFICATE 1 35 WELDINGMACHINE SHALL HAVE 3RD PARTY CALIBRATIONCERTIFICATE 1 36 DEWA SCOPE 1 36 1 SCAFFOLDING 1 36 2 CRANE 1 36 3 SUPPLY OF DN 600 PIPE1 36 4 SUPPLY OF DN 600 FLANGE 2 WARRANTY2 1 THE WARRANTY PERIOD FOR THE WORK SHALL BE ONE YEAR FROM THE DATE OF COMPLETION OF WORK CERTIFIED BY DEWA 2 2 IN CASE OF ANY DAMAGE DEFECT OF THEWORK CARRIED OUT UNDER THIS CONTRACT WITHIN THIS WARRANTYPERIOD THE CONTRACTOR SHALL ATTEND ANDCARRY OUT THE NECESSARY REPAIR WORK ANDRECTIFY THE DEFECT WITHIN SHORT PERIOD WITHOUTAFFECTING THE PRODUCTION OF ELECTRICITYAND WATER 3 INSURANCE 3 1 THECONTRACTOR SHALL BE RESPONSIBLE FOR THE INSURANCE OF ALL WORKS ANDPERSONNEL INVOLVED UNTIL THE WORKS ARETAKEN OVER BY THE COMPANY IN WRITING APPROPRIATEDOCUMENT PROOF TO BE PROVIDED TO DEWAPRIOR TO STARTING OF WORKS 4 GENERALTERMS CONDITIONS 4 1 THE CONTRACTORSHALL VISIT THE SITE AND BE FULLY FAMILIAR WITH THE WORKSCOPE PLANT ACCESS FACILITIES COMPLEXITIES SAFETY MEASURES ETC BEFOREHE SUBMIT HIS BID 4 2 THE CONTRACTOR SHALL ENSUREHOUSEKEEPING ON A DAILY BASIS AND THECONTRACTOR SHALL BE RESPONSIBLE FOR ALLWASTE MATERIALDISPOSALS TO DESIGNATED PLACES 4 3 ALLDEWA SAFETY ENVIRONMENT POLICY RULESAND REGULATION SHALL BE FOLLOWED AT WORKSITE DURING THE EXECUTION OF THE WORK THECONTRACTOR S ENGINEER SHOULD BE FAMILIARWITH SAFETY REGULATIONS WHILE WORKING IN AHAZARDOUS AREA 4 4 SCAFFOLDING IF REQUIRED SHALL BEARRANGED BY DEWA 4 5 QUALIFIED RIGGERSHALL BE ARRANGED BY CONTRACTOR FORRIGGING ACTIVITIES 4 6 THE WORK SHALL BE EXECUTED UNDERDEWA SUPERVISION AND AS PERQUALITY SCHEDULE REQUIREMENT 4 7 CONTRACTOR S SUPERVISOR SHALL BE AVAILABLE AT SITE THROUGHOUT THEPERIOD OF WORK 4 8 SERVICE AIR ELECTRICITYAND WATER FOR WORK AT DEWA SITE IT IS THE RESPONSIBILITY OF THE CONTRACTOR TO HAVE HISOWN ARRANGEMENT IN EXTENDING THEELECTRICITY AND WATER UTILITY TO HIS PLACESOF WORK INCLUDING LIGHTING 5 SAFETY HEALTH ANDENVIRONMENT 5 1 THE CONTRACTOR SHALLCOMPLY WITH ALL THE REQUIREMENTSSTIPULATED IN THE FOLLOWING OHS DOCUMENT FROM DEWA FOR HEALTH SAFETY AND ENVIRONMENTAL REQUIREMENTSDURING THE EXECUTION OF THE PROJECT 5 1 1 IMSP01 SP 06 H S PROCEDURE FOR CONTRACTOR ANDCONSULTANT 5 1 2 IMSP01 SP 15 CONTROL OFSUBSTANCES HAZARDOUS TO HEALTH COSHS 5 1 3 JAPS H 18 ENVIRONMENTAL MANAGEMENTSYSTEM PROCEDURE 5 2 THE CONTRACTOR SWORK WILL FALL WITHIN THE PURVIEW OF SAFETYSURVEYS CONDUCTED REGULARLY BY THE DEWA SAFETY SECTION ALL THEIR SAFETY REQUIREMENTS SHALL BE PROMPTLY MET THE CONTRACTOR SHALL CHECKTHE CONDITION SUITABLE TO CARRY OUT THE WORKCONDUCT SITE SURVEY AND SAFETY INSPECTIONTO ASSESS THE WORKING ENVIRONMENT 5 3 NO WASTAGES SHALL BE LEFT ON THE GROUND OR AT ANY AREABEING PART OF THE CONTRACTOR S WORK AREA SUGGESTED TO USE TARPAULIN AND OR MESHCOVER SURROUND SYSTEM 5 4 EXECUTION OF THE WORKON NG PIPING SHOULD NOT HINDER THEFUNCTION OF THE ADJOINING PIPES AND OTHERSYSTEMS ONLYNON SPARKING TOOLS AND PNEUMATICOPERATED MACHINES TO BE USE ALL THE TIMEWHEN WORKING IN NG AREA OR NEAR NG LINES ANY CONTRACTOR FOUND VIOLATING THE CODE WILL BEPROSECUTED AS PER DEWA RULES ANDREGULATION 5 5 MOBILE PHONES ARE NOTALLOWED NEAR NG LINES OR NG AREA 6 SECURITY PERMISSIONS 6 1 THE CONTRACTOR SHOULD SUBMIT THE FOLLOWINGPARTICULARS WELL IN ADVANCE FOR DEWA TOISSUE ENTRY PASSES FOR THEM VALID UP TO THE PERIOD OFCONTRACT WORK 6 1 1 LIST OF HIS STAFFPROPOSED TO BE ENGAGED ON THE JOB WITHDESIGNATION COPY OF THEIR VALID PASSPORT LABOR CARD ANDTWO PP SIZE PHOTOGRAPHS FOR VEHICLEDRIVERS COPIES OF THEIR VALID DRIVINGLICENSE ALSO ARE TO BE ATTACHED 6 1 2 LIST OF VEHICLESWITH A COPY OF VALID REGISTRATIONCERTIFICATE VEHICLE LICENSE OF EACHVEHICLE 6 1 3 LIST OF TOOLS EQUIPMENT CONSUMABLES ETC WITH DELIVERY NOTES FOR EACH 6 1 4 TRAVEL DECLARATION FORM6 1 5 UNDERTAKING LETTER 6 2 THE CONTRACTOR SHALL BRING THEIRMATERIALS EQUIPMENT OFFICE FACILITIES SUBSTANCES COMPUTERS CAMERAS ETC WITHTHEIR DELIVERY NOTE AFTER DEWA APPROVAL ONLY FOR THEINTENDED CONTRACT PURPOSE 6 3 ALLMATERIAL AND TOOLS BROUGHT IN SHALL BEDECLARED AT POWER STATION SECURITY GATE AND THE LIST OFTHESE ITEMS SHALL BE SIGNED BY DEWASECURITY THIS DOCUMENTS INCLSTANDARD TERMS CONDITIONS1 Prices should be DDP delivery duty paid at DEWA stores 2 Quotation to be submitted only in local currency U A E Dirhams3 DEWA Standard payment terms is 30 days credit from the date of acceptance of material4 No DEWA staff or his or her relatives up to third degree should have ownership or partnership in your company and your participation in DEWA tenders RFQs should not constitute a Conflict or perceived Conflict of Interest

Refer document

FileName	File Description
Global Tender Document	Tender Notice