Request For Quotation Purchase Of Goods

Plumbing Paste Set 270 G Provides Reliable Sealing Of Connections That Last For Many Years. Impregnating Flax With Paste Helps Protect It From Sticking, Drying Out And Destruction., Fireproof Mat Length, Cm 60. Width, Cm 50 Fireproof Mat Is Made Of Heat-Resistant Material. A Fireproof Mat Is Used To Protect Surfaces Near Stoves And Fireplaces From High Temperature Exposure. The Heat-Resistant Mat Is Made Of Fire-Resistant Fabric, Which Prevents Damage To The Flooring And Does Not Support The Spread Of Fire In The House And In The Tent., Extension Cord For Connecting To An Electrical Outlet (220V) 7-10 M Carrying Extension Cord 10 Meters With Three Sockets. Pva Cable 2×1.5 Mm², Rated Current 16 A, Maximum Power Up To 3.3 Kw. Rubber Plug And Socket Block., Sneakers Gray Size 43. 42Sizecoordinate With The Customer, Copper Fitting For Soldering Elbow With Socket 90 Degrees 22*22, Copper Fitting For Soldering Tee With Socket 22*22*22, Copper Fitting With Solder Socket 22*1/2 Hp, Copper Fitting With Solder Socket 22*3/4 Hp, Connector Press Angle 90 Degrees 22*22 For Stainless Steel, Connector Press Tee For Stainless Steel. 22*22*22, Protective Covers (Fender, Bumper)800*600Protective Covers (Steering Wheel, Seat, Gear Knob)Purpose: Protection Of The Paintwork Of The Hood And Fenders Of The Car From Mechanical Damage (Scratches From Buttons, Belts, Tools), Ingress Of Technical Fluids (Oils, Antifreeze, Brake Fluid), As Well As Dirt During Repair, Diagnostic And Service Work In The Engine Compartment.Scope Of Application: Service Stations (Sts), Car Services, Repair Areas Of Vehicle Fleets.Type: Universal Protective Cape For The Front Of The Car (Hood/Fenders)., Plate On Boring Cutter Thickness 3 Mm Plates Cutters Made Of Hard Alloys, With Mechanical Fastening Of Plates, Are Used In Metal Turning. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Plate For Cutting Cutter, Thickness 3 Mm Plates Cutters Made Of Hard Alloys, With Mechanical Fastening Of Plates, Are Used In Metal Turning. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Plate On A Passing Finishing Cutter At An Angle Of 35 Degrees, Thickness 3 Mm Plates. Cutters Made Of Hard Alloys, With Mechanically Fastened Plates, Are Used In Metal Turning. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Plate On A Straight Line Roughing Thickness 3 Mm Plates Cutters Made Of Hard Alloys, With Mechanical Fastening Of Plates, Are Used In Metal Turning. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Plate On Straight Through Roughing Ser2020k16 Thickness 3 Mm Plates Cutters Made Of Hard Alloys, With Mechanical Fastening Of Plates Are Used In Turning For Metals. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Plate For Thread-Cutting Cutter Ser2020k16 Thickness 3 Mm Plates Cutters Made Of Hard Alloys, With Mechanical Fastening Of Plates, Are Used In Metal Turning. All Characteristics Of The Plates Must Match The State Standardgost 18879-73, Gost 18874-73, Gost 18875-73, Gost 18882-73, Boots Materials:Lining: Padded Nylon, Sole: Polyurethane / Polyurethane, Protection: S3 / Src Sizes: 42, Light Blackfeatures: Waterproofoutsole Resists Oils And Chemicalspadded Heel Areametal Anti-Puncture Insolemetal Toe Cap Good Breathability, A Cylindrical Duralumin Rod (Volvanka) With A Diameter Of 100 Mm, The Total Length Must Be At Least 1 Meter (1000 Mm), In 1 Meter The Minimum Weight Must Be At Least 7-9 Kg.The Chemical Composition Should Be: Copper (4.5% By Weight), Magnesium (1.5%) And Manganese (0.5%); The Rest Is Aluminum (93.5%). When Testing Tensile Strength, The Typical Value Of The Yield Strength Of Duralumin Should Be 250 Mpa, The Short-Term Strength Limit Should Be 400...500 Mpa. All Testing Will Be Done Upon Receipt Of All Rods, Solder For Soldering Copper Pipes. Paste For Soldering Fittings With Soft Solder. To Be Agreed With The Customer.