Quotation Are Invited For Machining Of Ph-1 Service Air Compressor Crank Shaft Pulley-Side Bearing End Cover And Lube Oil Pump-Side Bearing Housing As Per The Required Dimensions

Quotation are invited for Machining of Ph-1 Service Air Compressor Crank Shaft Pulley-Side Bearing End Cover and Lube Oil Pump-Side Bearing Housing as Per the Required Dimensions D-St( Machining of Ph-1 Servi 1032604908 1 ITEM-00001 MACHINING OF PH1 SERVICE AIR COMPRESSOR CRANK SHAFT PULLEY-SIDE BEARINGEND COVER, QUANTITY:#2 NOS.SCOPE OF WORK1.#MACHINING AND BUSH REPLACEMENTO#MACHINE OUT AND REMOVE THE EXISTING DAMAGED BUSH OR MATERIAL FROMTHE BEARING END COVER.O#APPROXIMATE EXISTING BUSH DI MENSIONS:#Ø225 MM × 70 MM LENGTH.O#MANUFACTURE AND INSTALL A NEW BUSH USING#EN19 QT MATERIAL, AS PER THEAPPROVED SAMPLE/SPECIFICATIO N.O#CARRY OUT FINAL MACHINING OF THE NEW BUSH AS PER THE APPROVED SAMPLETO ACHIEVE THE REQUIRED#BEARING TIGHT FIT.O#FINAL BEARING SE AT DIMENSION:#OD Ø215 MM, AS REQUIRED.O#CARRY OUT FINAL MACHINING/GRINDING OF THE RELEVANT SURFACES TOACHIEVE THE REQUIRED DIMENSION S, FIT, AND SURFACE FINISH.O#APPROXIMATE OVERALL DIMENSIONS OF THE PULLEY-SIDE BEARING ENDCOVER:#OD Ø380 MM × 100 MM 2 JOB LENGTH.2.#MATER IAL COLLECTIONO#THE CONTRACTOR SHALL COLLECT THE PULLEY-SIDE BEARING END COVERSFROM#D-STATION, JEBEL ALI POWER STATION.3.#SITE VISIT O#THE CONTRACTOR SHALL ARRANGE A#SITE VISIT PRIOR TO SUBMISSION OF THEQUOTATION#TO OBTAIN A CLEAR UNDERSTANDING OF THE SCOPE OF WORK , EXISTINGCONDITION, AND DIMENSIONAL REQUIREMENTS.4.#INSPECTION AND DIMENSIONAL VERIFICATIONO#ALL MACHINING AND FITTING WORKS SHALL BE CARRIED OUT IN ACCORDANCEWITH THE APPROVED SAMPLE AND REQUIRED DIMENSIONS.O#FINAL DIMENSIONS SHALL BE INSPECTED AND VERIFIED PRIO R TO DELIVERY.5.#DELIVERYO#UPON COMPLETION OF THE MACHINING WORKS, THE BEARING END COVERS SHALLBE PROPERLY PACKED, PROTECTED, AND DE LIVERED TO THE DESIGNATED#DEWAWORKSHOP/LOCATION#AS INSTRUCTED.6.#WORK SCHEDULEO#THE WORK SHALL BE CARRIED OUT IN ACCORDANCE WITH#DEW AS WORK SCHEDULEAND INSTRUCTIONS.WARRANTY1.#THE WARRANTY PERIOD FOR THE COMPLETED MACHINING AND REFURBISHMENTWORKS SHALL BE#ONE (1) YEAR FROM THE DATE OF INSTALLATION OF THEPULLEY-SIDE BEARING END COVER ON THE COMPRESSOR.2.#IN THE EVENT OF ANY DAMAGE, DEFECT, OR FAILURE ATTRIBUTABLE TO THEWORK CARRIED OUT UNDER THIS CONTRACT DURING THE WARRANTY PERIOD, THECONTRACTOR SHALL ATTEND TO THE ISSUE AND CARRY OUT THE NECESSARY REPAIROR RECTIFICATION WORK WITHIN THE SHORTEST POSSIBLE TIME, AT#NOADDITIONAL COST TO DEWA.3.#THE CONTR ACTOR SHALL PROVIDE A#24-HOUR EMERGENCY CONTACT NUMBER D-ST( Machining of Ph-1 Service Air Compressor Crank Shaft Pulley-Side Bearing End Cover and Lube Oil Pump-Side Bearing housing as per therequired dimensions.)For technical quries contact [email protected] STANDARD TERMS & CONDITIONS 1) Prices should be DDP delivery duty paid at DEWA stores. 2) Quotation to be submitted only in local currency U.A.E Dirhams 3) DEWA Standard payment terms is 30 days credit from the date of acceptance of material 4) No DEWA staff or his or her relatives up to third degree should have ownership or partnership in your company, and your participation in DEWA tenders / RFQs should not constitute a Conflict or perceived Conflict of Interest. Supplier Registration: https://srm.dewa.gov.ae/irj/portal/anonymous/regis Tender Link : https://srm.dewa.gov.ae/sap/opu/odata/sap/ZSRM_RFX_REG_BID_SRV/AttachmentSet(2332602587)/$value