Tenders Are Invited For Acquisition Of Fixed Assets

Frame Slipway The Delivery Set Includes Installation And Connection. Platform Size 5200X2100mm. Load Capacity 3500 Kg.The Presence Of A Movable Support Allows You To Move The Slipway Around The Workshop. Using A Movable Support As A Platform Lifting Device. Does Not Require Electricity. All Operations Are Performed Using Compressed Air. Attaching Traction Towers Directly To The Frame At Any Point. Along The Entire Surface Of The Slipway There Are The Necessary Mounting Points For The Body Clamps. Two Carts For Rolling Up A Car With Damaged Wheels. Two Traction Towers With A Force Of 10 Tons Each. The Angle Of Application Of Force Is 360 Degrees. Contents: Platform – 1 Pc. Traction Tower With Chain And Hook – 2 Pcs. Pneumohydraulic Pump – 2 Pcs. Drive-In Ramps – 2 Pcs. Beam For Straightening The Roof – 1 Pc. Body Clamps – 4 Pcs. Rolling Cart – 2 Pcs. Support Support Posts – 2 Pcs. Chain Stop – 1 Pc. Set Of Clamps And Hooks. Technical Passport Operating Instructions Book Compliance With Technical Regulations/Standards Of The Republic Of Kazakhstan, The Delivery Set Includes Installation And Connection. 6 Operating Minimum Part Length 100 Mmminimum Part Width 60 Mmpanel Thickness From 10 To 55 Mmedge Width From 12 To 54 Mmedge Thickness From 0.5 To 5 Mmfeeding Speed 8-10-12 M/Mintotal Installed Power / Voltage 4.94 Kw / 380 V, 50 Hzair Pressure 6 Baroverall Dimensions B3150x1100x1350 Mmdesigned For Gluing Pvc, Abs, Melamine Edges Up To 5 Mm Thick On The Straight Ends Of Furniture Parts Made Of Chipboard, Mdf, Plywood. Heated Guide Plate - Dries And Heats The End Of The Part, Which Promotes Better Adhesion Of The Edge. Touchscreen Control Panel (Delta) - Simple And Intuitive Control Of Each Unit, Counter For The Number Of Parts And Edge Length.Motorized Lifting / Lowering Of The Pressure Beam - The Machine Is Adjusted To A Different Thickness Of Parts From The Control Panel.The Part Pre-Launch Protection System Will Prevent The Operator From Starting The Workpiece Ahead Of Time.Pre-Cutting And Edge Gluing Unit. Glues Evenly And Continuously. Automatic Control Of Glue Supply. Easy Adjustment For Different Edge Thicknesses. Special Spiral Design Of The Glue Tank.Trimming Knot. Infrared Sensors; Separate Trimming Of Front And Rear Overhangs. Two High Frequency Motors. 12’000 Rpmmilling Unit For Removing Overhangs. Separate Processing Of The Upper And Lower Parts. Two High Frequency Motors. 12’000 Rpmradius Scraping Unit With Carbide Knives, Corrects The “Wave” Effect, Removes Excess Gluethe Edge Polishing Unit, Driven By Two Motors, Finishes The Part.Operating Instructions Book, The Delivery Set Includes Installation And Connection. Length Of The Moving Table, Mm 3200Stroke Of The Moving Table, Mm 3200Width Of Movable Table, Mm 375Saw Angle 90° (Without Tilt)Largest Saw Diameter, Mm 305Cutting Height, Mm 70Diameter Of Cutting Blade, Mm 120Saw Spindle Diameter, Mm 30Scoring Blade Spindle Diameter, Mm 20Desk Dimensions, Mm 950 X 550Distance (Maximum) Between The Saw And The Side Base Ruler, Mm 1150Engine, Kw 5Scoring Device Motor, Kw 0.75Saw Speed, Rpm 5000Scoring Blade Speed, Rpm 8300Diameter Of The Chip Receiver Pipe Of The Saw Unit / Main Saw Guard, Mm 100 / 60Total Installed Power, Kw 5.75 Operating Instructions Book, The Delivery Set Includes Installation And Connection. Height, Mm1100length, Mm 1060Number Of Spindles, Pcs. 21Power, Kw 1.5Spindle Speed, Rpm 2800Working Area For The Machine, Mm3500 X 3500Desk Dimensions, Mm 890 X 625Distance Between Outer Spindles, Mm 640Distance Between Spindles, Mm 32Required Air Pressure, Bar6traverse Angle, °0 - 90Width, Mm 1050Pneumatic System Pressure, Bar6-8 Operating Instructions Book