Quotation Are Invited For Prodss Titanium Optical Dissolved Oxyge

Quotation are invited for Prodss Titanium Optical Dissolved Oxyge Delivery Date: 2027/01/29 Delivery To: Brandon Mark Wynne Scientific Services Delivery Address: 00 Waste Water Avenue Kewtown, Athlone Closing Date: 2026/09/16 Closing Time: 04:00 PM Description: 1 each x prodss titanium optical dissolved oxyge 4 each x prodss odo sensor caps Specification: * ProDSS ODO Titanium Optical Dissolved Oxygen Sensor Specifications Accuracy 0 to 200%: ±1% of reading or 1% saturation, whichever is greater 200 to 500%: ±8% of reading 0 to 20 mg/L: ±0.1 mg/L or 1% of reading, whichever is greater 20 to 50 mg/L: ±8% of reading Equipment used with ProDSS Handheld and cable assemblies Measurement Range 0 to 500%, 0 to 50 mg/L Resolution 0.01 mg/L and 0.1%, or 0.1 mg/L and 1% (user selectable) ProDSS ODO Sensor cap Specifications Replacement optical dissolved oxygen (ODO) sensor cap designed for use with the ProDSS ODO Optical Dissolved Oxygen Sensor . Sensor Type: Optical luminescent dissolved oxygen sensing technology. Compatibility: Specifically compatible with the ProDSS handheld system and the titanium ProDSS ODO smart sensor. Warranty: 1 year. Expected Service Life: Typically 15 to 18 months under normal operating conditions. Replacement Type: User-replaceable in the field without returning the sensor to the manufacturer. [ysi.com] Calibration Data: Each replacement cap is supplied with sensor cap coefficients/calibration data that must be entered or recognized during installation. Contact Brandon Mark Wynne Contact 021 444 9142 IMPORTANT: QUOTATION CONDITIONS: The quotation condition listed below are in addition to those contained in the CCT standard quotation conditions and must be fully complied with: Clause 3: General Obligations 3.6.1.1 For this quotation, purchase orders / works packages will be determined and created as follows: 3.6.1.1.1 Based on the total amount as reflected on the Price Schedule and to the supplier as awarded by the SCM delegated authority. GUIDELINE: Wherever reference is made to any Trademark, Name, Patent, Design, Type, Specific Origin or Producer, such reference shall be deemed to be accompanied by the words "or equivalent". CLAUSE - 2.14.1 & 2.15 Provide, on request by the CCT, any other material that has a bearing on the quotation offer, the suppliers commercial position (including joint venture agreements), preferencing arrangements, or samples of materials considered necessary by the CCT for the purpose of the evaluation of the quotation. If the Specifications require the supplier to provide samples/technical data sheets, these shall be provided strictly in accordance with the instructions set out in the Specification. If such samples /technical data sheets are not submitted as required in the bid documents or within any further time stipulated by the CCT in writing, then the bid concerned will be declared non-responsive. The Municipal Bidding Document 6.1 is attached, to be eligible for preference points bidders are required to submit a duly completed, current dated MBD 6.1 document with supporting documents with every RFQ submission, failure to submit will result in zero-point allocation. Please note that the MBD6.1 document is valid a year from date of signature. Failure to comply with the above will result in a zero (0) allocation for preference points. INSURANCE DOCUMENTS: Ensure that all required insurances such as your Public liability, Employers liability or COIDA and motor vehicle insurance are attached and that they are up to date. * ProDSS ODO Titanium Optical Dissolved Oxygen Sensor Specifications Accuracy 0 to 200%: ±1% of reading or 1% saturation, whichever is greater 200 to 500%: ±8% of reading 0 to 20 mg/L: ±0.1 mg/L or 1% of reading, whichever is greater 20 to 50 mg/L: ±8% of reading Equipment used with ProDSS Handheld and cable assemblies Measurement Range 0 to 500%, 0 to 50 mg/L Resolution 0.01 mg/L and 0.1%, or 0.1 mg/L and 1% (user selectable) ProDSS ODO Sensor cap Specifications Replacement optical dissolved oxygen (ODO) sensor cap designed for use with the ProDSS ODO Optical Dissolved Oxygen Sensor . Sensor Type: Optical luminescent dissolved oxygen sensing technology. Compatibility: Specifically compatible with the ProDSS handheld system and the titanium ProDSS ODO smart sensor. Warranty: 1 year. Expected Service Life: Typically 15 to 18 months under normal operating conditions. Replacement Type: User-replaceable in the field without returning the sensor to the manufacturer. [ysi.com] Calibration Data: Each replacement cap is supplied with sensor cap coefficients/calibration data that must be entered or recognized during installation. Contact Brandon Mark Wynne Contact 021 444 9142 Tender Link : https://web1.capetown.gov.za/web1/procurementportal/RFQ/Details/328869