Quotation Are Invited For Supply And Installation Of Metallic Grills

Quotation are invited for Supply and Installation of Metallic Grills at Mzuzu Fuel Depot and Completion of Minor Outstanding Works at Blantyre, Lilongwe and Chipoka Fuel Depot. A Provision of equipment and mobilisation Sum 1 B Metallic Grilles (500mm wide in 1metre lengths) Supply and install metallic grilles in 50mmx50mmX6mm thick 4.47kg/m steel angle iron frame and 50x6mm steel flat bars spaced at 30mm, apply red oxide primer and gloss black paint 1 MCC side metre 30 2 Front of stores (along road from dipping gantry to stores) metre 60 3 Along the road adjacent to TLF metre 60 4 Slop Tank side metre 25 5 Behind pump house metre 30 6 At slop tank area towards TLF bay metre 25 7 Interceptor side at TLF metre 15 8 Dipping gantry side metre 50 C Provision for Remove and straighten bent Metallic grills at the TLF bay Sum 1 D Supply and install new Matty roller door at product pump house fitting a door of 2015mm maintaining the existing specs of the door Each 1 E Provision for supply and installation of metallic bollard, 1.2m high above the ground, spaced 2.5 m apart and painting in chevron along water pipe opposite TLF, 25cm away from the pipe F Modification of slop tank access ladders to make uniform spacing of the steps and tread surfaces Rise: 230 mm 5 Going (tread depth): 250 mm Uniform rise and tread throughout Ladder angle:75 Degrees Lilongwe Depot A Provision for equipment and mobilisation Sum 1 B Modification of slop tank access ladders to make uniform spacing of the steps and tread surfaces Rise: 230 mm Going (tread depth): 250 mm Uniform rise and tread throughout Ladder angle:75 Degrees Sum 1 C Provision for supply and installation of metallic bollard, 1.2m high above the ground, spaced 2.5 m apart and painting in chevron along water pipe opposite TLF, 25cm away from the pipe m 100 BLANTYRE DEPOT A Provision of equipment and mobilisation Sum 1 B Provision of concrete humps and rumble strips 1. 50 mm in height, 500mm wide circular humps on two sides of the junction after the guard house. Position 10m from the Stop label Each 2 2. 70mm in height 6m long trapezoidal humps covering the span of the road. Painting chevron for visibility 20m before the boom barrier Each 1 3 50 mm in height, 500mm wide circular humps covering the span of the road. Painting chevron for visibility Each 2 6 I. One at 10m after barrier gate II. One at 10m before entrance gate III. One at 10m after entrance gate towards rail E Provision for installation of kerbs for closing the route to old emergency gate, painting in chevron sum 1 F Installation of signage 50m before barrier gate Each 1 Modification of slop tank access ladders to make uniform spacing of the steps and tread surfaces Rise: 250 mm Going (tread depth): 250 mm Uniform rise and tread throughout Ladder angle:75 Degrees Sum 1 Chipoka Depot A Provision for equipment and mobilisation B Modification of slop tank access ladders to make uniform spacing of the steps and tread surfaces Rise: 250 mm Going (tread depth): 250 mm Uniform rise and tread throughout Ladder angle:75 Degrees each 2 C Modification on the diesel tanks 1 and 2 stair and platform 1 Remove and dispose of the existing damaged checker plate stair treads from the diesel tank access stair. Each 15 7 Supply and install new 3 mm thick mild steel checker plate treads, each measuring 600 mm × 250 mm, bolted to the existing stair structure. Modify the existing stair arrangement by repositioning or installing the treads as necessary to achieve uniform rise and tread spacing of 250 mm throughout the stairway. 2 Remove the existing platform checker plate, including all associated bolts, nuts, and washers, taking care not to damage the supporting steelwork. Supply and install a new 3 mm thick mild steel checker plate, 500 mm wide and cut to match the existing platform dimensions. m 15 3 Supply, fabricate and install one vertical structural steel support to the inclined stair at mid-span. The support shall comprise a 100 × 100 × 6 mm SHS steel post (or approved equivalent) complete with a welded 250 × 250 × 16 mm base plate. Secure the base plate to the existing reinforced concrete slab using four M20 anchor bolt Tender Link : https://ppda.mw/storage/documents/opentenders/NOC30-%20Metallic%20Grilles%20&%20minor%20works.pdf