Request For Quotation Purchasing Construction Goods

Portland Cement. Characteristics. Strength Grade: M 500; Strength Class According To: Cem I 42.5N; Type Of Cement: Portland Cement Without Mineral Additives Or With Minimal Additives; Normal Hardening Speed: N (Normal Hardening); Color: Grey; Binder: Clinker + Gypsum. Technical Characteristics: Compressive Strength After 28 Days: ≥ 42.5 Mpa; Compliance With The Brand Is About 500 Kgf/Cm²; Beginning Of Setting: No Earlier Than 45 Minutes; End Of Setting: No More Than 10 Hours; Bulk Density: Not Less Than 1100–1300 Kg/M³; True Density: About 3100 Kg/M³; High Water Resistance And Frost Resistance Of Cement-Based Concrete; Average Heat Release During Hydration; Shrinkage Is Minimal. In One Pack: At Least 50 Kg., Metal Profile Post, Steel, Galvanized, Designed For Installation Of Sectional Fencing Made Of Welded 3D Mesh, For Outdoor Use. Characteristics. Profile Cross-Section: No Less Than 60 × 40 Mm; Height (Length): Not Less Than 2.5 M; Material: Structural Steel; Wall Thickness: Not Less Than 1.5 Mm; Coating: Galvanized / Galvanized With Polymer Coating; Installation Type: Concreting Or Flange Mounting; Coating Color: Green, Polymer Powder Coated; Purpose: For Fastening Sections Of Fencing, Gates And Light Gates., Fastening Bracket For 3D Panels. Characteristics. Pole Size: No Less Than 60×40 Mm; Mounting Hole Diameter: At Least 8–10 Mm; Bracket Width: At Least 20–40 Mm; Bracket Length: At Least 40–70 Mm; Material: Made From Galvanized Steel Sheet With A Thickness Of 1.2 To 2 Mm, Which Prevents Corrosion. Polymer Coating: For A Harmonious Look, The Part Is Coated With Powder Paint In The Color Of The Fence. Plastic Compensator (Liner): Repeats The Shape Of The Cell And Clamps The Rod (Diameter From 3 To 5 Mm). Complete Set, Per Mounting Unit: Mounting Bracket, At Least 1 Pc.; Bolt M8×40 At Least 1 Pc.; M8 Nut At Least 1 Pc.; Washer At Least 1–2 Pcs., Swing Gates Made Of 3D Welded Mesh. Characteristics. Gate Type: Double-Leaf Swing; Total Passage Width: Not Less Than 5000 Mm; Height: Not Less Than 2400 Mm; Infill: 3D Welded Panel; Wire Diameter: Not Less Than 4 Mm; Cell Size: No Less Than 50×200 Mm (Typical); Material: Galvanized Steel Wire. Low Carbon Steel, Zinc Coating Provides Protection Against Atmospheric Corrosion. The Thickness Of The Zinc Layer Is Usually From 40 To 100 Microns; Coating: Hot-Dip Galvanized Or Galvanized With Polymer Coating; Support Pillars: Profile Pipe No Less Than 80×80 Mm; Opening: Outward Or Inward; Opening Angle: Up To 180°; Locking Device: Hasp, Padlock Lugs Or Mortise Lock. Delivery Set: At Least 2 Gate Leaves (At Least 60*40*1.5 Mm); At Least 2 Support Pillars (At Least 80*80*2 Mm); Adjustable Hinges At Least 4 Pcs; Sash Retainer; Latch (Latch); Fasteners; Lugs For A Padlock Or Built-In Mortise Lock With Keys., Swing Gate For 3D Fencing. Characteristics. Opening Size, Width: Height: Not Less Than 2000 Mm; Width: Not Less Than 1000 Mm; Color: Green; Opening Type: Right Or Left; Opening Angle: Up To 180°; Frame And Pillar Material: Steel Profile Pipe; Frame Cross-Section: Not Less Than 40×40×1.5 Mm; Cross-Section Of Pillars: Not Less Than 60×60×1.5–2.0 Mm; Height Of Pillars: Not Less Than 3000 Mm (For Concreting); Filling: Welded 3D Panel With V-Shaped Bends Of Rigidity. The Wire Diameter Most Often Ranges From 3.0 To 5.0 Mm; Cell Size: No Less Than 50×200 Mm; Coating: Polymer Powder Coating (Ppc) Over Galvanized Steel. It Protects The Metal From Corrosion, Ultraviolet Radiation And Fading. Delivery Set: No Less Than A Gate Leaf; At Least 2 Support Pillars; Adjustable Hinges; Latch, Padlock Lugs Or Integral Mortise Lock With At Least 2 Handles And Keys., Quartz Sand (Or River Sand). Characteristics. Fractional Composition: Not Less Than 0.06–1.2 Mm; Origin: Natural Quartz Or River Sand; Grain Shape: Acute, Crushed Or Partially Rounded; Color: Light Yellow, White Or Grey; The Content Of Clay And Dust Particles Is Not More Than 1.0%; Free Of Clay Impurities In Lumps And Organic Impurities; Humidity Upon Delivery: No More Than 5%; Bulk Density: Not Less Than 1300–1500 Kg/M³; True Grain Density: No Less Than 2600–2650 Kg/M³; Mohs Hardness 7 (High Abrasion Resistance); Filtration Coefficient: Not Less Than 5 M/Day., Two-Component Polyurethane Adhesive For Lawn And Artificial Grass. Characteristics. Composition: Component A: Polyurethane Resin; Component B: Isocyanate Hardener; Does Not Contain Water Or Organic Solvents. Blend Color: Beige/Light Brown; Component Ratio: Approximately 9:1 By Weight; Viability Of The Mixture At +20°C: No More Than 30–60 Minutes; Primary Setting: At Least 6–12 Hours; Complete Curing: At Least 24–48 Hours; Consumption For Artificial Grass: Approximately 0.8–1.2 Kg/M²; Working Temperature Of Application: From +10°C To +30°C; Operating Temperature From −40°C To +120°C; Density Of Component A: About 1.5–1.7 G/Cm³; Density Of Component B: About 1.1–1.2 G/Cm³. Properties: High Elasticity, No Shrinkage, Moisture Resistance, Resistance To Weathering And Temperature Changes. The Kit Contains Two Components: Component A: Basic Paste (Polyurethane Resin With Fillers); Part B: Liquid Hardener (Isocyanate) In A Separate Small Bottle., Laminated Chipboard. Characteristics. Color Range: Neutral Light Gray Shade That Easily Combines With Both Bright Colors And Wood Decors.; Surface Type, Texture: Shagreen / Pe (Fine Grain); Base: Chipboard, Emission Class E1-E0.5; Thickness: No Less Than 16 Mm / 18 Mm; Sheet Format, Length: No Less Than 2800; Width: Not Less Than 2070 Mm; Sheet Area: Not Less Than 5.03 M²; Density: Usually Varies From 650 To 750 Kg/M³; Lamination On Both Sides; Variety1., Non-Woven Needle-Punched Material. Characteristics. Material Type: Non-Woven Needle-Punched Geotextile; Surface Density: No Less Than 200 G/M² (Weight Tolerance ≤ 8-10%); Thickness Of The Canvas: At Least 1.4 – 2.5 Mm (Measured Under A Load Of 2 Kpa); Breaking Load (Strength): No Less Than 5.0 – 7.0 Kn/M; Удлинение При Разрыве: В Пределах 50 – 140% (Обеспечивает Высокую Эластичность И Устойчивость К Разрывам); Punching Strength: Not Less Than 600 – 800 N; Filtration Coefficient: ~50 ± 15% M/Day (At A Pressure Of 2.0 Kpa); Размер Пор (Фильтрующая Способность): Не Более 130 Мкм (Эффективно Задерживает Частицы Грунта); Roll Size: No Less Than 2 × 50 M; Total Area Of ​​The Canvas Per Roll: Not Less Than 100 M²; Material (Composition): 100% Polyester Or Polypropylene; Color: Mix (A Mixture Of Polyester Fibers Of Various Shades), Portland Cement With Mineral Additives; Strength Class: Cem Ii/A-Sh 42.5N (Cem Ii: Portland Cement With Mineral Additives; /A-Sh: Granulated Blast Furnace Slag Is Used As An Additive In An Amount From 6% To 20% (Category A); Strength Class That Guarantees Withstanding A Compressive Load Of At Least 42.5 Mpa. N: Normally Hardening Cement That Gains Design Strength In A Standard Time (At Least 28 Days). Ss: Sulfate-Resistant Portland Cement). Strength Grade: Not Lower Than M500 (Capable Of Withstanding Loads Of Up To 500 Kg Per \(1\) Sq. Cm Of Finished Concrete); Color: Grey. One Pack Must Contain At Least 50 Kg., Universal Docking Strip. Characteristics. Product Type: Docking Strip; Purpose: Design And Protection Of Joints Of Facade Panels, Siding And Other Facing Materials; Decorative Closing Of Installation Gaps; Protection Of Joints From Moisture And Contamination. Width (Visible Part): Not Less Than 50 Mm; Height (Bend Depth): Not Less Than 18 Mm; Length: Not Less Than 3000 Mm; Metal Thickness: Most Often Not Less Than 0.5 Mm; Material: Galvanized Steel With A Protective And Decorative Polymer Coating (Polyester)., Internal Plug-In Plastic Plug For Profile Pipe. Characteristics. Shape: Rectangular; Fitting: In A Profile Pipe; Pipe Size: No Less Than 60×40 Mm; Pipe Wall Thickness: At Least 1.0–3.0 Mm; Height Of The Landing Part: Not Less Than 15–25 Mm; Height Of The Outer Cover: At Least 2–5 Mm; Total Height Of The Product: At Least 17–30 Mm; Material: Low Pressure Polyethylene (Hdpe) Or Polypropylene (Pp); Color: Black; Design: Top Cover With Rounded Corners; Elastic Spacer Ribs For Reliable Fixation Inside The Pipe; Impact Resistant Design., 3D Fencing Panel. Panel Size: Width: Not Less Than 2500 Mm; Height: Not Less Than 2030 Mm; Construction Type: Welded Sectional 3D Panel; The Thickness Of The Horizontal And Vertical Rods Is At Least 5.0 Mm, Providing High Strength, Resistance To Deformation And Protection From Vandalism; Material: Galvanized Steel Wire; Cell Size: No Less Than 50 × 200 Mm; Number Of Stiffening Ribs: At Least 4–5 Pieces, With A V-Shaped Bend Along The Height Of The Panel To Protect Against Deflection; Coating: Zinc And/Or Polymer Powder.