Ultrasonic Therapeutic Dual-Frequency Emitter (Or Equivalent). Purpose: Converting High-Frequency Electrical Vibrations Into Ultrasonic Mechanical Vibrations For Ultrasound Therapy And Phonophoresis Procedures. Multi-Frequency (Dual-Frequency) Nominal Operating Frequencies 0.88 Mhz And 2.64 Mhz (Allowed Deviation Of Frequency 0.88 Mhz ±0.009 Mhz, Frequency 2.64 Mhz ±0.03 Mhz) Nominal Effective Radiating Surface Area 4.0 Cm² Ultrasonic Vibration Generation Mode Supports Continuous And Pulsed Operating Modes (Depending On The Capabilities Of The Main Device) Range Values Of The Set Ultrasound Intensity At Least 5 Fixed Steps: 0.05; 0.2; 0.4; 0.7; 1.0 W/Cm² Maximum Output Power Of Ultrasonic Vibrations Not Less Than 4.0 W Design Features (Waterproof) The Emitter Must Have A Waterproof Design Up To The Control Mark On The Body (For Procedures In An Aquatic Environment). Scope Of Application General Physiotherapy And Cosmetology Compatibility Full Compatibility With Ultrasonic Therapy Devices Of The Uzt Series Of Dual-Frequency Modifications (For Example, Uzt-1.3.01F Or Equivalent). Registration: The Product Must Have A Valid Registration Certificate (Ra) From The Ministry Of Health For Medical Use. Safety: Compliance With The Class Of Protection Against Electric Shock - Ii, Type B (According To Gost R Iec 60601-1) Operating Conditions: Uninterrupted Operation In Intermittent And Short-Term Mode. Operating Temperature Range From +10°С To +35°С, Relative Humidity Up To 80%. Delivery Contents: Emitter With Built-In Connecting Cable - 6 Pcs., Battery Battery 12V 150 Mah /Hi-Mh 500 Mah 1.2 V For Heater Fabie - 4300 (10 Pcs Batteries In One Set), Battery Type: For For Aitecs 2016 Syringe Infusion Pump Nickel-Metal Hydride (Ni-Mh) Nominal Voltage: 7.2 V (V) Nominal Capacity: Not Less Than 2700 Mah (Mah) Design (Configuration): Battery Assembly Of 6 Aa Type Cells (In One Row, Serial Connection) Presence Of Board Control/Protection: Integrated Control Circuit Board With Installed Fuse (F1) And Interface Connector Connector Type: Pin Connector (Micro Connector, Pitch 1.25Mm / 2.0Mm, 2-Pin) On Flexible Leads Purpose: Backup/Autonomous Power Supply For Specialized Equipment, Electrode Mask (Manufactured As A Specialized Current Cable For Electrical Sleep). Suitable For The Eleskulap (Med Teco) Line Of Devices: Eleskulap-2, Eleskulap-02M, Eleskulap-03M, Eleskulap-05M, As Well As The Combined Device “Med Teco Afk”. 2 Independent Poles (Anode And Cathode). The Cable Has A Bifurcated Design (One Branch Goes To The Eye Electrodes, The Second To The Occipital Electrodes). Medical Elastic Rubber Yellow (Or Flesh-Colored). Has Perforated Holes Along The Entire Length For Manual Adjustment Of The Head Circumference. Reusable Metal Cup Electrodes (Mounted Directly Into Rubber Straps). There Are 4 Cups In Total (2 For The Eye Sockets, 2 For The Back Of The Head). Single Pole Banana Plugs Ø 2Mm (Some Older Revisions Used 4Mm Standard) With Colored Heat Shrink (Red/Black) To Maintain Polarity. About 1.5 – 2 Meters (Provides A Comfortable Distance For The Patient From The Device). Flexible Medical Polyvinyl Chloride (Pvc) With Copper Conductor Inside. Allows Repeated Disinfection By Wiping With A 3% Hydrogen Peroxide Solution With The Addition Of 0.5% Detergent Or Other Disinfectants Approved By The Ministry Of Health Of The Russian Federation., Feeder-Electrical Holder For Uhf 60 Designed To Hold And Fix Replaceable Capacitor Electrodes In A Given Position, As Well As To Transmit High-Frequency Energy From The Electronic Unit Of The Device To The Electrode. Designflexible, Articulated, Adjustable, In A Protective Insulating White Corrugated Plastic Shell. There Is A Conductive Cable (Feeder) Inside. Connection Elements – On One Side: Metal Plug (Bayonet/Cylindrical Connector) For Secure Connection Into The Socket On The Side Panel Of The Device. – On The Other Side: Rotating Joint With Screw Lock And Threaded/Receiving Hole For Clamping And Screwing On Replacement Electrodes. Compatible Electrode Diameters Provides Rigid Fixation For Standard 36Mm, 80Mm And 120Mm Diameter Disc Electrodes. Operating Frequency Designed To Operate At The Nominal Frequency Of The Device: 27.12 Mhz ± 0.163 Mhz. Throughput Power Must Withstand High-Frequency Load With Stepwise Adjustment Of The Device Output Power Up To 60 W Inclusive. Overall Dimensions (Approximately) Length Of The Electrode Holder Assembly: (720 X 30 X 45) Mm ± 10%. Safety And Quality Requirements The Product Must Be Made Of High-Quality Dielectric Materials That Are Resistant To Disinfection With Chemical Solutions Approved In Medical Practice. Ensuring Electrical Safety Of Patients And Staff From Burns From Hf Currents. “The Supplied Electrode Holder Must Correspond To The Modification Of The Customer’S Device (Internal Cable Routing). By Agreement With The Customer, It Is Required To Provide A Photo Or Drawing Of The Connectors To Confirm Compatibility Before Delivery.”
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
