Request For Quotation 03. Metal Gates. Horizontal, Metal Blinds. (Z.524)

03. Functional, Technical, Quality, Operational Characteristics: Roller Shutters Made Of Foam-Filled Profile. Profile Width Is At Least 45 Mm. Design With Overall Dimensions 1300×1900 Mm, White (Ral 9003) With A Tubular Electric Motor, With An Additional Emergency Manual Lifting Mechanism. The Blade Is Fixed In Side Guide Rails With A Seal For A Tight Fit And Smooth Movement. Control: Electric Drive With Emergency Opening. The Set Includes 2 Remote Controls. Certificate, 03. Metal Swing Gates (Double-Leaf). Overall Dimensions Of The Opening (W×H): 2500 × 2500 Mm. Frame Of The Doors: Made Of Rectangular Steel Profile With A Cross-Section Of At Least 60×40×2 Mm (According To Gost 32931). The Design Must Ensure Rigidity And Absence Of Deformation Under Its Own Weight. Filling Material: Sandwich Panels Filled With Polyisocyanurate Foam (Pir) Or Equivalent With Similar Thermal Insulation Properties. Complete Set And Fittings: Support Posts (Pillars): Steel Profile With A Cross-Section Of At Least 100×100×4 Mm (To Ensure Resistance To Wind Loads According To Class 1 According To Gost). Hinges: On Support Bearings, With A Diameter Of At Least 30 Mm - 3 Pcs. For Each Sash. Locking Devices: Lower Vertical Valves (Stoppers) - 2 Pcs. Central Locking Device For A Padlock With Metal Eyes No Less Than 4 Mm Thick. Handles: Metal Brackets On Both Sides. Anti-Corrosion Protection: Metal Surfaces Must Be Cleaned, Degreased And Primed. The Final Coating Is Polymer Powder Or Enamel Type Pf-115 In Two Layers, Color Ral7004. Gost 31174-2017. Certificate, 03. Functional, Technical, Quality, Performance Characteristics: Fire-Resistant Single-Leaf Sliding Gates With A Fire Resistance Rating Of At Least Ei60, Size 3000X3000 Mm. The Door Leaf Is Made Of Fire-Resistant Panels With Mineral Wool Filling And Is Equipped With A Bottom Brush Seal For Additional Insulation. Automation System With Industrial Electric Drive For Gates Weighing Up To 1300 Kg. Electromechanical Drive With A Work Intensity Of 70%, Equipped With A Gearbox In An “Oil Bath” For Operation At Temperatures From -40°C To +55°C. Built-In Control Unit With Radio Receiver, Protection Class Ip54 And Supports Integration With Fire Safety Systems For Automatic Closing Of The Shutter. The Delivery Set Includes Three Linear Meters Of Rack-8 Rack (30X8 Mm), A Pair Of Four-Channel Remote Controls Operating At A Frequency Of 433 Mhz And One Set Of Wired Safety Photocells. With The Ability To Integrate With A Fire Alarm System To Ensure Automatic Closure In The Event Of An Emergency. Certificate, 03. Lifting Sectional Doors With Wicket, Series Isd01. Overall Dimensions (W×H): 4000X3500 Mm. High Rise (The Guides Go Vertically Up Above The Opening Before Turning To The Ceiling). Fabric Material: - Sandwich Panels With A Thickness Of At Least 40 Mm Made Of Galvanized Steel Filled With Polyurethane Foam. Panel Structure With Anti-Finger Pinch Protection, Outer Side - “Stucco” (Orange Peel) Or Microwave. Torsion Mechanism With A Resource Of At Least 25,000 Cycles. Color (External) Ral 9002 (Light Grey/White Grey). The Presence Of A Mortise Gate With A Threshold (No More Than 100 Mm), A Closer And A Lock, Dimensions 900X2100 Mm. Shaft Drive (Axial) For Industrial Doors. Power Supply 220V. Protection Class Not Lower Than Ip54. Includes Control Unit And 2 Remote Controls. Photocells (Receiver And Transmitter) Are Installed In The Opening To Prevent Closure If There Is An Obstacle. Availability Of Devices For Protection Against Cable Breakage And Protection Against Spring Breakage (Shaft Blocking). A System Of Seals Around The Entire Perimeter Of The Opening, Gate And Between Panels. Gost 31174-2017. Certificate, 03. Metal Swing Gates (Double-Leaf). Overall Dimensions (W×H): 2000 × 2200 Mm. Frame Of The Doors: Made Of Rectangular Steel Profile With A Cross-Section Of At Least 60×40×2 Mm (According To Gost 32931). The Design Must Ensure Rigidity And Absence Of Deformation Under Its Own Weight. Filling Material: Sandwich Panels Filled With Polyisocyanurate Foam (Pir) Or Equivalent With Similar Thermal Insulation Properties. Complete Set And Fittings: Support Posts (Pillars): Steel Profile With A Cross-Section Of At Least 100×100×4 Mm (To Ensure Resistance To Wind Loads According To Class 1 According To Gost). Hinges: On Support Bearings, With A Diameter Of At Least 30 Mm - 3 Pcs. For Each Sash. Locking Devices: Lower Vertical Valves (Stoppers) - 2 Pcs. Central Locking Device For A Padlock With Metal Eyes No Less Than 4 Mm Thick. Handles: Metal Brackets On Both Sides. Anti-Corrosion Protection: All Metal Surfaces Must Be Cleaned, Degreased And Primed. The Final Coating Is Polymer Powder Or Enamel Type Pf-115 In Two Layers, Color Ral7004. Gost 31174-2017. Certificate