Request For Quotation Consumables For Fpv Components

Steel Corner (Hot-Rolled Steel Corner) 3 M Long. Designed For Equipping Sheds For Storing Drones. Steel Equal-Flange Corner No Less Than 40×40×3 Mm, Hot-Rolled, Steel St3 (Gost 8509-93), Length No Less Than 3 M, Weight No Less Than 1.85 Kg/M No Less Than 5.55 Kg, Material – Carbon Structural Steel, Shape – L-Shaped With Equal Flanges, Standard Dimensional Tolerances. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., A Set Of Heat-Shrinkable Tubes Of At Least 4 1/0.5 Mm, 522 Pieces Of Tubes (In Assortment): Diameter Of At Least 1.5–2 Mm - 500 Pcs. (Pieces Of 50–100 Mm), Diameter Of At Least 3–4 Mm – 400 Pcs. (Pieces), Diameter Of At Least 5–6 Mm - 300 Pcs. (Pieces), Diameter Of At Least 8–10 Mm - 200 Pcs. (Segments), Color Black/Red/Blue/Yellow (Assorted), Shrinkage Ratio 2:1, Intended For Insulating And Marking Wires And Connections. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Epoxy Resin No Less Than 5 Kg, Hardener (Included With The Resin Or Separately) No Less Than 2.5 Kg, Reinforcing Fabric (Fiberglass) No Less Than 10 M², Plastic Measuring Containers No Less Than 5 Pcs., Paint Brushes No Less Than 10 Pcs., Protective Gloves (Nitrile/Latex) No Less Than 10 Pairs. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Applied To A Base Of Oxford 210Den, It Is A Lightweight Waterproof, Windproof Fabric That Slightly Rustles And Resembles The Density Of Bologna. The Reverse Surface Has A Polymer Coating With A Width Of At Least 150 Centimeters And A Length Of At Least 50 M. Products Must Meet Or Be Higher Than The Standards Specified In The Technical Specifications. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Soldering Kit: Tin-Lead Solder 60/40 (Diameter 1.0 Mm) No Less Than 200 G, Soldering Flux (Gel) No Less Than 50 G, Rosin No Less Than 50 G, Braid For Removing Solder No Less Than 1 Pc. (Length 1.5 M), Replaceable Soldering Tips At Least 2 Pcs., Tip Cleaner (Heat-Resistant Sponge) At Least 1 Pc., Mounting Tweezers At Least 1 Pc., Soldering Holder (Mini-Third Hand Or Board Clamp) At Least 1 Pc. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Abs+Carbon Fibers. Printing Temperature: At Least 230-260 C. Table Temperature At Least 70-90 C, Printing Speed At Least 40-60 Mm/S. Shrinkage Low (Better Than Abs). Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Petg+Carbon Fibers. Printing Temperature: At Least 230-260 C. Table Temperature At Least 70-90 C, Printing Speed At Least 40-60 Mm/S. Shrinkage Low (Better Than Abs). Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Power Cable No Less Than 2×1.5 Mm² – 30 M, Power Cable No Less Than 2×0.75 Mm² – 10 M, Signal Cable No Less Than 4×0.5 Mm² – 12 M, Utp Cat5e Twisted Pair Cable No Less Than 10 M, Installation Wire No Less Than 0.5 Mm² – 15 M, Silicone Power Cable 14–16 Awg Not Less Than 10 M, Set Of Connectors And Terminals (Xt60, Jst.) - 1 Set. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., 0M X 0.15Mm X 8Mm Battery Spot Welding And Soldering Is A High Quality Material Designed For Joining Battery Cells In Batteries, Assembling Lithium Ion (Li-Ion), Lithium Polymer (Li-Po) And Other Battery Packs. Products Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Hot-Melt Adhesive Rods (Eva): Diameter 7 Mm, At Least 12 Pcs. (Length 100–200 Mm, Assorted), Diameter 11 Mm, At Least 8 Pcs. (Length 100–300 Mm, Assorted), Melting Point Not Less Than 150–200 °C. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Chipboard No Less Than 16 Mm 1 Pc Material: Laminated Chipboard Thickness: No Less Than 16 Mm Formaldehyde Emission Class: E1 (For Residential Premises) Surface Type: Smooth, Matte / Semi-Matte Dimensions: No Less Than 2750 × 1830 Mm 2800 × 2070 Mm (Depending On The Manufacturer) Thickness Tolerance: No Less Than 0.3 Mm. Goods Must Meet Or Exceed The Standards Specified In The Technical Specification. Final Acceptance Of The Work Results Is Carried Out By The Customer Only After Successful Acceptance, The Goods Acceptance Certificate Is Signed. If Deficiencies Are Identified In The Process, The Customer Has The Right Not To Sign The Report Until The Identified Defects Are Completely Eliminated., Material Pla+Carbon Fibers. Strength Is Higher Than That Of Regular Pla, Especially In Bending And Stretching. The Supplier Supplies Components (Spare Parts) In Accordance With The Technical Specifications Agreed With The Customer. All Supplied Components Are Subject To Prior Approval With The Customer Prior To Delivery.