Bids Are Invited For Acquisition And Installation Of Furniture (Tables And Chairs) To Service The Municipal Secretariat Of Tourism Sector In The Municipality Of Sao Mateus/Es.

Rectangular Table Pe Panel With Pedestal Auxiliary Table 03 Drawers, Top Made Of Mdp Sheet, With Selected Reforestation Wood Particles, Bonded And Consolidated With Synthetic And Thermo Resin Stabilized Under Pressure, 25Mm Thick, Coated, On Both Faces, With Melamine Thermopressed Film, Thick Minimum 0.2Mm. The Contour Of The Top Is Topped With A 2.5 Mm Pvc Edge, Hot Glued, With A Radius Of 2.5 Mm In Accordance With Abnt Standards. Side Panels Made Of Mdp Sheet, 25Mm Thick, Coated On Both Sides. The Contour Of The Panels Is Topped With A 0.45Mm Pvc Edge. Front Panel Made From 18Mm Thick Mdp Plate, On Both Sides. The Front Panel Is Headed On The Apparent Tops With 0.45Mm Pvc Edge. High-Impact Thermoplastic Polystyrene Spacers, Measuring 80X25x10mm, Used Between The Top And Side Panel To Help Pass Cabling. Fastening System (Assembly) Is Made Using A Zamac Metal Bushing With M6 Millimeter Thread With Zinc Finish, The Same Being Fully Impregnated Into The Parts And Minifix Zamac Screw With M6 Millimeter Thread, With Minifix Drum Assembly, Thus Forming A Set For Assembly And Disassembly Without Damaging The Product. Set Of Bushing And Leveling Shoe In Injected Polypropylene And Metal Rod With Adjustment Through 5/16 Thread, Applied To The Side Panels, Whose Function Is To Overcome Any Uneven Floors. Side Drawer With 02 Drawers And 01 Folder: Top Made Of 25Mm Thick Mdp Sheet, Coated On Both Faces With Melamine Thermo-Pressed Film, 2Mm. The Top And Header On All Tops With 1 Mm Pvc Edge Tape, Hot Glued. Body And Drawers In 15Mm Thick Mdp, Header On Exposed Tops With 0.45Mm Pvc Edge Tape. Fronts In 15 Mm Thick Mdp, Headboard On All Sides, Swivel Chair With Canvas Back And Armrest. Seat With Set Consisting Of A 12 Mm Thick Laminated Wood Structure With ¼ Claw Nuts, Made Of Carbon Steel And Coated Using The Zinc Electroplating Process, Fixed To The Mounting Points Of The Structure. One (01) Flexible Foam Cushion Based On Polyurethane (Pu) Is Attached To The Seat Structure, Ergonomic And Manufactured Using Chemical Systems Based On Polyol / Isocyanate Using The Pressure Injection Process. This Cushion Has A Controlled Density Of 45 To 50 Kg/M3, Variations In The Order Of +/-2 Kg/M3 May Occur. The Set Is Covered With Vinyl Laminate Using The Conventional Taping Process. Its Dimensions Revolve Around 500 Mm (Width) X 450 Mm (Depth) Featuring Rounded Corners At Its Ends. The Seat Also Has A Plastic Fairing Manufactured Using The Thermoplastic Injection Process In Polypropylene. The Seat Height Adjustment Allows It To Meet Minimum Measurements Of 420 Mm Up To A Maximum Height Of 530 Mm, With Small Variations Possible. To Mount The Armrest To The Seat, Two Hexagon Screws Are Used For Each Armrest. The Chair Is Also Offered With The Option Of Backrest Height Adjustment, Allowing The Lumbar Support To Be Adjusted To An Even Wider Range Of Body Types. The Mechanism Has Two Levers, Two Of Which Work By Turning, One Located On The Right Side, Which Controls The Activation Of The Gas Column, To Adjust The Height Of The Chair, And The Other Located On The Left.