Bids Are Invited For The Purpose Of This Bidding Process Is To Record Prices For Possible Future Acquisitions Of Materials And/Or Provision Of Specialized Services, Intended For The Implementation, Maintenance And Replacement Of Horizontal, Vertical And Safety Road Signs.

Supply And Installation Of Type Ii Monodirectional Retroreflective Stud, In Yellow Or White Color, Made Of Polyester Resin Or Synthetic Resin Of High Mechanical Resistance With Mineral Filler Dolomite, Equipped With A Retroreflective Lens With Anti-Abrasive Coating, In Accordance With Abnt Nbr 14636:2021. The Tack Must Have A Body With Dimensions Of Approximately 100 By 80 By 22 Millimeters, Within The Dimensional Tolerances Permitted By The Standard. Fixing Must Be Carried Out Using A 5/16 Inch By 2 Inch Zinc-Plated Metal Pin Or Screw, Guaranteeing Resistance Exceeding 15,000 Kgf. The Material Supplied Must Be Accompanied By A Conformity Report Issued By An Accredited Laboratory, Proving Full Compliance With The Current Standard., Supply And Installation Of Type Ii Bidirectional Retroreflective Tack, Supply And Installation Of Monodirectional Retroreflective Tack, Made Of Polyester Resin Or Synthetic Resin With High Mechanical Resistance, In Accordance With Abnt Nbr 15576:2015. The Tack Must Have A Rectangular Body With Domed Surfaces, Meeting The Normative Dimensions Established In Table 3 Of The Standard, With An Approximate Measurement Of 250 By 150 By 50 Millimeters Within The Permitted Tolerances. The Fastening System Must Include Two Metal Pins With A Diameter Of 12.7 ± 1.3 Millimeters, A Height Of 50 ± 5 Millimeters And A Minimum Spacing Of 120 Millimeters, Guaranteeing Resistance Greater Than 15,000 Kgf. Retroreflective Lenses Must Have A Minimum Length Of 100 Millimeters And A Minimum Width Of 15 Millimeters, With An Anti-Abrasive Coating. The Material Must Be Accompanied By A Conformity Report Issued By An Accredited Laboratory, Supply And Installation Of A Bidirectional Retroreflective Tack, Supply And Installation Of A Flexible Bollard Measuring 94 Cm In Height, With An Approximate Weight Of 2.5 Kilograms, A Cylindrical Body Measuring 10 Cm In Diameter And A Circular Base Measuring 28 Cm In Diameter. Joao Bobo Type Automatic Return System, Obtained By A Set Of Elastic Bands On The Attachable Base, Allowing Flexion And Return To Vertical Position After Impact. Fixing To The Floor Using 4 Anchor Screws Included. The Bollard Must Have Side Holes For The Passage Of Chains, Ropes Or Signaling Tapes, Enabling The Delimitation And/Or Isolation Of Areas. Product Made Of Polyethylene With Protection Against Uv Rays, Resistant To Adverse Weather Conditions. Available Colors: Black Body With Yellow Reflective Strips Or Orange Body With White Reflective Strips., 04/17/2026 - 17:34:08, 04/17/2026 - 17:34:09, 04/17/2026 - 17:34:10, Complete Removal Of Tactile Or Vertical Signaling Devices Fixed To The Floor, Including Tacks, Tacks, Reflective Caps Or Markers, With Removal Of The Element, Cleaning, Removal Of Waste, Recomposition Of The Floor And Adequate Disposal Of Materials, Including All Labor, Tools, Equipment And Necessary Inputs., Supply Of Plates For Vertical Signage Made Of Galvanized Steel Sheet By Immersion In Water. Warm, With Nominal Thickness Of 1.25 Millimeters, In Compliance With Abnt Nbr 11904:2015. The Plates Must Be Cut Without Burrs, With Rounded Corners, And Prepared To Receive A Retroreflective Film. The Main Face Must Receive A Type Ii Prismatic Retroreflective Film, In Accordance With Abnt Nbr 14644:2013, With A Minimum Guarantee Of Seven Years Regarding Durability, Photometric Performance And Resistance To