Tenders Are Invited For Renewal Of Hydraulic, Electrical And Control Installation Frisiabrêge In Franeker Specifications 25-34-Kb.

The Work To Be Carried Out In Relation To The Frisiabrêge Mainly Consists Of, But Is Not Limited To, The Manufacture, Delivery, Installation And Complete Operational Delivery Of: 1. Dismantling And Removing The Existing E&Ia Installation; 2. Dismantle And Dispose Of Existing Hu Set; 3. Replace Hu Set And Overhaul Complete Hydraulic Installation; 4. Cleaning And Preserving Designated Bridge Parts And Structures; 5. Replace Complete E&Ia Installation Including All Cabling; 6. Revised Closure Plan On The South Side Of The Bridge According To The New (Plot) Drawing; 7. Move Position Three (3) Barrier Boxes On The Southern Main Road Towards The Fall; 8. Six (6) Pieces Of Completely New Barriers Incl. Columns According To Nen6787. 9. Make All Six (6) Asb Cabinets In Type Nma-Bas 1; 10. New Barrier Barriers According To Nen6787 And No Longer Use Wokkel Marking; 11. Six (6) Eba Speakers To Be Installed In The New Asb Cabinets; 12. New Marine Radio Station Including Directional Antennas On The New Tilting Mast On The Basement Deck; 13. Replacing And Installing Weather Facilities On The Tilting Mast On The Basement Deck; 14. Completely New Mep Audio Equipment For 8 Zones (2 Pieces Pau); 15. Three (3) Horn Loudspeakers For Speaking/Listening To Road Traffic; 16. Two (2) Horn Loudspeakers For Speaking/Listening To Shipping Traffic; 17. One (1) Piece (Small) Horn Speaker For Speaking/Listening Cbk Bridge Cellar; 18. Maintain Both Registration Posts And Provide Each With New Speakers; 19. Install Two (2) New Reporting Buttons And Signage On Each Registration Post; 20. Maintain Existing Front Signals At Approximately 150M But Connect Them With New Cables; 21. Newly Coat All Six (6) Stop Signal Masts In Accordance With Nen3322 Black/White Checkered; 22. Move The Position Of Three (3) Stop Signal Masts On The Southern Main Road Towards The Fall; 23. All Stop Signal Masts Equipped With New 3-Aspect Led2 Signals Red-Yellow-Red; 24. Two (2) Parallel Road Stop Signal Masts Fitted With New Underlights; 25. Apply Six (6) New Boom Control Units (Bsu) For Asb In Cbk; 26. Apply Six (6) New Eba Boards For Asb In Cbk; 27. Replace All Shipping Signals Including Odvs On Existing (Tilting) Structures; 28. Execute Shipping Signals Svs And Odvs In Led2 According To Plot Drawing; 29. Power Supply Distributor Incl. Kwh Maintain With Fuses Of 3 * 250A+ N+Pe; 30. Supply And Install A Completely New Control Box (Cbk) Approx. 3.2 * 2.0 * 0.6M; 31. New Network Cabinet Pf For Remote Control Pf As Part Of The Cbk; 32. Maintain Existing Ups Cabinet For 19 Patch Panels At Existing Location; 33. Move Of (Long-Distance) 2U Patch Panel To The Ups Cabinet To Be Maintained; 34. Two (2) Pieces Of New Encoder Using Standard Software; 35. Replace Existing Encoders Compared To Current Transmissions Of Main Pivot Points; 36. New Hu Set Using Two (2) Pieces Controlling Sto Soft Starters; 37. New Hu Control Using 2 Control Units Based On Digital Control And Feedback; 38. Integrating Redundancy (Half Speed) Based On A Single Hu Set 41. Reusing All Existing Camera Masts; 42. Installing 6V Mm Fiber Optic Routes To 5 Existing Camera Masts; 45. Installing A Second Connection Box In A Cabinet With A Viewing Door Near The Basement Entrance; Plc And Head Station In Network Section According To Blueprint Pf; 47. Remote Control Entirely According To Typicals / Standard Software Pf V. 4.0; 48. Control Installation Completely Replaced By Fail-Safe Plc / Hmi Facilities; 49. Existing Cabling Via Existing Water And Road Crossings Entirely Replace; 52. Reuse Existing Cable Paths As Much As Possible After Removing Old Cables; 53. Move Patch Panel, 2He For 1 * 96V Sm Fiber Optics To Ups Cabinet 54. All Additional Required Excavation And Cable Work; 58. Documentation And Registration.